| Age | Commit message (Collapse) | Author |
|---|
|
Merge commit 752451f01c45 ("Merge branch 'i2c-embedded/for-next' of
git://git.pengutronix.de/git/wsa/linux") resulted in a build breakage
for OMAP
arch/arm/mach-omap2/i2c.c: In function 'omap_pm_set_max_mpu_wakeup_lat_compat':
arch/arm/mach-omap2/i2c.c:130:2: error: implicit declaration of function 'omap_pm_set_max_mpu_wakeup_lat'
make[1]: *** [arch/arm/mach-omap2/i2c.o] Error 1
Fix this by including the appropriate header file with the function
prototype.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
|
|
Pull ARM SoC fixes from Olof Johansson:
"This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really."
There was some concern about commit 68136b10 ("RM: sunxi: Change device
tree naming scheme for sunxi"), but Tony says:
"Looks like that's trivial to fix as needed, no need to rebuild the
branch to fix that AFAIK.
The fix can be done once Olof is available online again.
Linus, I suggest that you go ahead and pull this if there are no other
issues with this branch."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: sunxi: Change device tree naming scheme for sunxi
ARM: ux500: fix missing include
ARM: u300: delete custom pin hog code
ARM: davinci: fix build break due to missing include
ARM: exynos: Fix warning due to missing 'inline' in stub
ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
ARM: dts: mx27: Fix the AIPI bus for FEC
ARM: OMAP2+: common: remove use of vram
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
...
|
|
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
|
|
Pull battery update, part 2, from Anton Vorontsov:
"These are left overs that I didn't have time to review/apply before
the merge window opened. I didn't want to "spoil" the first pull
request with these late patches, so they were not included:
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be
probed. It was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling."
* tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6:
charger-manager: Fix bug when check dropped voltage after fullbatt event
charger-manager: Fix bug related to checking fully charged state of battery
ARM: OMAP: rx51: Register platform device for rx51_battery
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"Nothing all that exciting; a new module-from-fd syscall for those who
want to verify the source of the module (ChromeOS) and/or use standard
IMA on it or other security hooks."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Fix kbuild output when using default extra_certificates
MODSIGN: Avoid using .incbin in C source
modules: don't hand 0 to vmalloc.
module: Remove a extra null character at the top of module->strtab.
ASN.1: Use the ASN1_LONG_TAG and ASN1_INDEFINITE_LENGTH constants
ASN.1: Define indefinite length marker constant
moduleparam: use __UNIQUE_ID()
__UNIQUE_ID()
MODSIGN: Add modules_sign make target
powerpc: add finit_module syscall.
ima: support new kernel module syscall
add finit_module syscall to asm-generic
ARM: add finit_module syscall to ARM
security: introduce kernel_module_from_file hook
module: add flags arg to sys_finit_module()
module: add syscall to load module from fd
|
|
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
|
|
into fixes
* tag 'ep93xx-fixes-for-3.8' of git://github.com/RyanMallon/linux-ep93xx:
ARM: ep93xx: properly wait for UART FIFO to be empty
|
|
fixes
From Sascha Hauer:
ARM i.MX fixes for v3.8-rc
This fixes a compile failure on imx_v4_v5_defconfig and a regression
introduced with enabling the MIPI clocks on i.MX51. Also one rather
cosmetic fix for the i.MX27 dts file.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
ARM: dts: mx27: Fix the AIPI bus for FEC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
These patches fixes a build error caused by a merge
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.
* tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: common: remove use of vram
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
mfd: omap-usb-host: get rid of cpu_is_omap..() macros
ARM: OMAP: Remove debug-devices.c
ARM: OMAP2420: Fix ethernet support for OMAP2420 H4
OMAP2+: mux: Fixed gpio mux mode analysis
OMAP: board-files: fix i2c_bus for tfp410
ARM: OMAP2+: Fix sparse warnings in timer.c
ARM: AM335x: Fix warning in timer.c
ARM: OMAP2+: Fix realtime_counter_init warning in timer.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley per Tony Lindgrens request:
Fix some OMAP4 clock problems, and deal with some sparse warnings from
the OMAP CPUIdle code.
* tag 'omap-fixes-a-for-v3.8-window' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
|
|
rtc-omap driver is now capable of handling kicker mechanism, hence remove
kicker handling at platform level, instead provide proper device name so
that driver can handle kicker mechanism by itself
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Brings some 52xx updates. Also manually merged tools/perf/perf.h.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There is several different SoCs sharing the sun5i codename: A10s, A12
and A13. Since there is enough differences to not consider those the
same SoCs, change a bit the naming scheme to reflect this.
Moreover, some boards like the olinuxino come in A10s and A13 variants,
which also share the same SoC codename.
So change the naming scheme to reflect both the codename and the market
name of the SoCs used in the dtsi and in the board files
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit db298da2c31e1dcf7c9b7c9cef6217ad3449ebb7
"ARM: nomadik: move platform_data definition"
moved the Ux500-specific musb header from <mach/usb.h>
to <linux/platform_data/usb-musb-ux500.h>
However that makes some board code fail to compile
now:
CC arch/arm/mach-ux500/board-mop500.o
linux/arch/arm/mach-ux500/cpu-db8500.c: In function 'u8500_init_devices':
linux/arch/arm/mach-ux500/cpu-db8500.c:226:2: error: implicit declaration of function 'ux500_add_usb' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [arch/arm/mach-ux500/cpu-db8500.o] Error 1
make[3]: *** Waiting for unfinished jobs....
make[2]: *** [arch/arm/mach-ux500] Error 2
make[2]: *** Waiting for unfinished jobs....
So fix this up by adding the proper include file that
appears to have been brought in implicitly one or another
way in the past.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With recent changes in the kernel, the MMCI and PL011 UART
drivers will autonomously request their pins to be muxed in,
so this machine-specific pin hogging code is just interfering
with the proper mechanism and causing regressions in the v3.8
kernel. Delete it and the problems go away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into fixes
ARM: tegra: fixes for 3.8
This branch contains a few miscellaneous fixes that have shown up in the
last few weeks.
By Sivaram Nair (2) and Hiroshi Doyu (1)
via Stephen Warren
* tag 'tegra-for-3.8-fixes-for-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
amba: tegra-ahb: Fix warning w/o PM_SLEEP
ARM: tegra: fix comment in dsib clk set_parent
ARM: tegra: select correct parent clk for pll_p
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
arch/arm/mach-davinci/board-da850-evm.c: In function 'da850_evm_init':
arch/arm/mach-davinci/board-da850-evm.c:1516:2: error: implicit declaration of function 'sram_get_gen_pool' [-Werror=implicit-function-declaration]
arch/arm/mach-davinci/board-da850-evm.c:1516:31: warning: assignment makes pointer from integer without a cast [enabled by default]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
|
|
In file included from arch/arm/mach-exynos/clock-exynos5.c:29:0:
arch/arm/mach-exynos/common.h:28:12: warning: 'exynos_pm_late_initcall' defined but not used [-Wunused-function]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull DRM updates from Dave Airlie:
"This is the one and only next pull for 3.8, we had a regression we
found last week, so I was waiting for that to resolve itself, and I
ended up with some Intel fixes on top as well.
Highlights:
- new driver: nvidia tegra 20/30/hdmi support
- radeon: add support for previously unused DMA engines, more HDMI
regs, eviction speeds ups and fixes
- i915: HSW support enable, agp removal on GEN6, seqno wrapping
- exynos: IPP subsystem support (image post proc), HDMI
- nouveau: display class reworking, nv20->40 z compression
- ttm: start of locking fixes, rcu usage for lookups,
- core: documentation updates, docbook integration, monotonic clock
usage, move from connector to object properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (590 commits)
drm/exynos: add gsc ipp driver
drm/exynos: add rotator ipp driver
drm/exynos: add fimc ipp driver
drm/exynos: add iommu support for ipp
drm/exynos: add ipp subsystem
drm/exynos: support device tree for fimd
radeon: fix regression with eviction since evict caching changes
drm/radeon: add more pedantic checks in the CP DMA checker
drm/radeon: bump version for CS ioctl support for async DMA
drm/radeon: enable the async DMA rings in the CS ioctl
drm/radeon: add VM CS parser support for async DMA on cayman/TN/SI
drm/radeon/kms: add evergreen/cayman CS parser for async DMA (v2)
drm/radeon/kms: add 6xx/7xx CS parser for async DMA (v2)
drm/radeon: fix htile buffer size computation for command stream checker
drm/radeon: fix fence locking in the pageflip callback
drm/radeon: make indirect register access concurrency-safe
drm/radeon: add W|RREG32_IDX for MM_INDEX|DATA based mmio accesss
drm/exynos: support extended screen coordinate of fimd
drm/exynos: fix x, y coordinates for right bottom pixel
drm/exynos: fix fb offset calculation for plane
...
|
|
Move platform-mx2-emma to arch/arm/mach-imx/devices and fix the following build
error:
make[2]: *** No rule to make target `arch/arm/mach-imx/devices/platform-mx2-emma.o', needed by `arch/arm/mach-imx/devices/built-in.o'. Stop.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The MIPI/HSP clocks were recently turned on in the i.MX51 clock tree.
It turned out that the system does not work properly when the MIPI/HSP
clocks are enabled, but the IPU clock is disabled. This happens when
IPU support is disabled. In this case the IPU clock gets disabled when
the clock framework turns off unused clock in a late_initcall. This
is broken since:
| commit 9a2d4825a9368e018003a2732a61be063d178f67
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date: Tue Jun 5 13:53:32 2012 +0200
|
| ARM i.MX5: switch IPU clk support to devicetree bindings
|
| The i.MX5 clk support has platform based clock bindings for the
| IPU. IPU support is devicetree only, so move them over to devicetree
| based bindings. Also, enable MIPI clocks which do not have a device
| associated with, but still need to be enabled to do graphics on
| i.MX51.
This patch fixes this by setting some reserved bits in the CCM as recommended
in the reference manual.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
|
|
FEC controller is connected to AIPI2 bus.
Also fix the AIPI1 address range.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This is needed to make the battery monitor actually work on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
omap-for-v3.8/fixes-for-merge-window-v2
|
|
commit 966458f OMAP: remove vram allocator
Removed the OMAP specific vram allocator but OMAP2 common was
still trying to use it and this lead to the following build error:
CC arch/arm/mach-omap2/common.o
arch/arm/mach-omap2/common.c:19:23: fatal error: plat/vram.h: No such file or directory
compilation terminated.
make[1]: *** [arch/arm/mach-omap2/common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull fbdev changes from Tomi Valkeinen:
"OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming
common display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller"
* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
drivers/video: add support for the Solomon SSD1307 OLED Controller
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
...
Conflicts:
arch/arm/mach-davinci/devices-da8xx.c
arch/arm/plat-omap/common.c
drivers/media/platform/omap/omap_vout.c
|
|
|
|
Change the value of status to disabled to keep the consistent
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fix the following sparse warnings in the OMAP3/4 CPUIdle code:
arch/arm/mach-omap2/cpuidle34xx.c:272:1: warning: symbol 'omap3_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle34xx.c:274:23: warning: symbol 'omap3_idle_driver' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:164:1: warning: symbol 'omap4_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:166:23: warning: symbol 'omap4_idle_driver' was not declared. Should it be static?
Also fix the following checkpatch warnings:
WARNING: please, no space before tabs
#44: FILE: arch/arm/mach-omap2/cpuidle34xx.c:105:
+^I.name = ^I"omap3_idle",$
WARNING: please, no space before tabs
#45: FILE: arch/arm/mach-omap2/cpuidle34xx.c:106:
+^I.owner = ^ITHIS_MODULE,$
ERROR: code indent should use tabs where possible
#211: FILE: arch/arm/mach-omap2/cpuidle44xx.c:74:
+ /* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */$
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Booting OMAP4460 Pandaboard ES with a recent u-boot results in this
warning:
WARNING: at arch/arm/mach-omap2/dpll3xxx.c:427 omap3_noncore_dpll_enable+0xf4/0x110()
The OMAP4 DPLL parent clock names only listed the reference clocks,
not the bypass clocks. Fix by adding the bypass clocks to the DPLL
parent lists.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
The OMAP4 clock divider "div_iva_hs_clk" is listed in the clock data
as an OMAP HSDIVIDER, but it's actually a power-of-two divider. This
causes a warning during boot on an OMAP4460 Pandaboard-ES with a
recent u-boot:
WARNING: at arch/arm/mach-omap2/clkt_clksel.c:143 omap2_clksel_recalc+0xf4/0x12c()
clock: div_iva_hs_clk: could not find fieldval 0 for parent dpll_core_m5x2_ck
Fix by converting the data for this clock to a power-of-two divider.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
Commit d043d87 (ARM: OMAP2+: clockdomain: bypass clockdomain handling
when disabling unused clks) skips the decrementing of a clock-domains
use count if the clocks use count is zero. However, for OMAP4 devices
this is causing the EMU clock-domain to be stuck ON as the use count is
not getting decremented correctly.
The scenario that leads to this problem is described below ...
omap_hwmod_setup_all
--> _setup
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 1
--> _enable_clocks
--> clk_enable
--> trace_clk_div_div usecount = 1
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 2
--> _idle
--> _disable_clocks
--> clk_disable
--> trace_clk_div_div usecount = 0
--> clkdm_hwmod_disable
--> skips decrement of EMU clock domain usecount
because trace_clk_div_div is 0!
--> EMU clock domain usecount = 2
--> clkdm_hwmod_disable
--> EMU clock domain usecount = 1
Hence, due to the order that a clocks use count is decremented and the
clock domain is disabled, it is possible that the clock domain can have
a non-zero use count when the actual clock has a use count of 0.
Therefore, we should only bypass the clock-domain handling when both the
clock-domain and clock in the clock-domain have a use count of 0 and
warn when the clock-domain has a zero use count and the clock has a
non-zero use count.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
With the latest mainline u-boot bootloader (v2012.10), timers (5-8) in
the ABE power domain are failing to turn-on. The timers never come out
of the disabled state when setting the module-mode field to enable.
The problem was exposed when u-boot was updated to NOT configure and
lock the ABE DPLL on start-up. If the ABE DPLL is configured and locked
by u-boot the problem does not occur. However, if the ABE DPLL is in the
idle low-power bypass state and we attempt to enable a timer in the ABE
power domain, it remains stuck in the disabled state. It appears to be a
problem the timer interface clock as this comes from the ABE DPLL.
If we place the ABE DPLL in the MN-bypass state and not the idle
low-power state, then this problem is not seen.
This problem only appears to occur on OMAP4460 and not OMAP4430.
Workaround this problem by locking the ABE DPLL for OMAP4460 in the
kernel on boot. By locking the ABE DPLL, when clocks from the ABE DPLL
are not being requested the DPLL will transition into a low-power stop
mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can
be enabled or disabled in addition to the standard configurable
multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X
multiplier is accounted for by checking to see whether it is enabled or
not. However, when calculating a new rate we only check to see if the
rate can be achieved with the current setting for the 4X multiplier.
Enhance the round_rate() function for such DPLLs to see if the rate
can be achieved with the 4X multiplier if it cannot be achieved without
the 4X multiplier.
This change is necessary, because when using the 32kHz clock as the
source clock for the ABE DPLL, the default DPLL frequency for the ABE
DPLL cannot be achieved without enabling the 4X multiplier.
When using the 32kHz clock as the source clock for the ABE DPLL and
attempting to lock the DPLL to 98.304MHz (default frequency), it was
found that the DPLL would fail to lock if the low-power mode for the DPLL
was not enabled. From reviewing boot-loader settings that configure the
ABE DPLL it was found that the low-power mode is enabled when using the
32kHz clock source, however, the documentation for OMAP does not state
that this is a requirement. Therefore, introduce a new function for
OMAP4 devices to see if low-power mode can be enabled when calculating a
new rate to ensure the DPLL will lock.
New variables for the last calculated 4X multiplier and low-power
setting have been added to the dpll data structure as well as variables
defining the bit mask for enabling these features via the DPLL's
control_reg. It is possible that we could eliminate these bit masks from
the dpll data structure as these bit masks are not unique to OMAP4, if
it is preferred.
The function omap3_noncore_program_dpll() has been updated to avoid
passing the calculated values for the multiplier (M) and divider (N) as
these are stored in the clk structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Currently all OMAP4 non-core DPLLs use the same function table for
configuring DPLLs. For these DPLLs, the function
omap4_dpll_regm4xen_recalc() is used to recalculate the DPLL rate and
the function omap4_dpll_regm4xen_round_rate() is used to calculate the
closest rate to that requested. However, these omap4_dpll_regm4xen_xxx()
functions are only applicable to the ABE DPLL and not the other non-core
DPLLs. Therefore, add a new function table for non-core DPLLs that do
not include the 4X-multiplier (M4X).
Please note that using these omap4_dpll_regm4x_xxx() function works for
the non-M4X DPLLs today because we only check to see if the 4X
multiplier is enabled when calculating the rate. However, it is planned
that the dpll functions will be enhanced to enable the 4X multiplier as
necessary (in order to achieve the requested rate) and so calling these
functions for non-M4X dplls will no longer work.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit "ARM: dts: OMAP4: Update timer addresses" updated the device-tree
names of the OMAP4 timers 5-7 because the default address for the timers
was changed from the L3 address to the MPU private address. When booting
with device-tree, this introduces a regression when attempting to set
the parent clock of timers 5-7 to the sys_clk_div_ck. Therefore, update
the clock aliases for timer 5-7 to reflect the updated device-tree name
for the timers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply after the CCF conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
|
|
We need to move this file to allow ARM multiplatform configurations
to build for omap2+. This can now be done as this file now only
contains platform_data.
cc: Russell King <linux@arm.linux.org.uk>
cc: Alan Cox <alan@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Govindraj.R <govindraj.raja@ti.com>
cc: Kevin Hilman <khilman@ti.com>
cc: linux-serial@vger.kernel.org
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 0d9250c (ARM: dts: omap4-panda: Add pinmux configuration for
HDMI) added a new device-tree source file for Rev A4 of the OMAP4430
Panda board but it did not add this version to the makefile. Hence,
add this file to the makefile.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The system memory node for the OMAP2420 H4 was incorrectly defined as
start address followed by end address, instead of start address and
size. No noticable side-effects were observed but fix this for
correctness.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
"This branch contains device-tree updates for the SPEAr platform. They
had dependencies on earlier branches from this merge window, which is
why they were broken out in a separate branch."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
ARM: SPEAr1310: Fix AUXDATA for compact flash controller
ARM: SPEAr13xx: Remove fields not required for ssp controller
ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
ARM: SPEAr: DT: Update device nodes
ARM: SPEAr: DT: add uart state to fix warning
ARM: SPEAr: DT: Modify DT bindings for STMMAC
ARM: SPEAr: DT: Fix existing DT support
ARM: SPEAr: DT: Update partition info for MTD devices
ARM: SPEAr: DT: Update pinctrl list
ARM: SPEAr13xx: DT: Add spics gpio controller nodes
|
|
Pull ARM Soc updates, take 2, from Olof Johansson:
"This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that
we couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform."
Fix up conflicts mostly as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
sh: clkfwk: fixup unsed variable warning
Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
ARM: highbank: use common debug_ll_io_init
ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
ARM: shmobile: sh7372: remove fsidivx clock
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
|
|
Merging in the smp-on-socfpga branch into soc2 since the topics are similar
and it's a short branch in the first place.
* next/smp:
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.
The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP2420 H4 board was the only board using the
plat-omap/debug-devices.c code for configuring ethernet support. Now
that OMAP2420 H4 has been migrated to use the generic gpmc code for
configuring ethernet support, the debug-devices.c file is no longer
used and so remove it and its header file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Ethernet is not currently working on the OMAP2420 H4 board. In commit
f604931 (ARM: OMAP: abstract debug card setup (smc, leds)) the function
h4_init_smc91x() that initialised the ethernet controller was renamed to
h4_init_debug() but was never called when initialising the board.
Adding a call to h4_init_debug() fixes ethernet support, however,
instead of using the legacy H4 code migrate the H4 to use the
gpmc_smc91x_init() function instead and remove the legacy H4 code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP_MODE_GPIO() macro verified only OMAP_MUX_MODE4.
It is not correct for following platforms:
2430 - gpio mux mode 3
44xx - gpio mux mode 3
54xx - gpio mux mode 6
Patch reserves first 3 bits in partition flags for storing gpio mux
mode in same format as stored in control pad register.
Modified OMAP_MODE_GPIO() macro to handle all possible cases of gpio mux mode.
Modified omap_mux_init() flags of omap34xx to include OMAP_MUX_GPIO_IN_MODE4.
Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
