| Age | Commit message (Collapse) | Author |
|---|
|
If the TPA6130 is compiled as module the id and power_gpio values are
arbitrary at module probing time since the rx51_tpa6130a2_data was marked as
__initdata. Fix this by using __initdata_or_module. Then __initdata is
defined only if the kernel is built without CONFIG_MODULES and omitted
otherwise.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After commit ed919b0 "mmc: sdio: fix runtime PM anomalies by introducing
MMC_CAP_POWER_OFF_CARD" it is required to specify MMC_CAP_POWER_OFF_CARD
to have runtime PM support. As the wl1251 driver expects card to be
powered down when it's not used, wifi will no longer work after interface
is brought down at least once without functioning runtime PM.
Fix this by declaring MMC_CAP_POWER_OFF_CARD for MMC3.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds omap_reserve functionality to board-omap4panda.c.
Helps in the reserving boot time memory in SDRAM, used here for
framebuffer allocation.
This patch is in similar lines to commit id 71ee7dad9b6991, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tony@atomide.com: fixed to be before .map_io as pointed out by Russell King]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Register TWL6030 PWM, which is used as charging LED
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Register BH1780GLI Ambient light sensor, which is an I2C device
for 4430SDP board.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Make sure the LED is turned off at boot time, and configure the GPIO LED
device as active low.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
gpio_direction_output() has a value argument, there's no need to call
gpio_set_value() explicitly right after.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
No need to call this early from init_irq. Also recent changes
initialize GPIO now later, so calling gpio_request from init_irq
will make it fail.
While at it, also remove the unnecessary EXPORT_SYMBOL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 72f381ba056 (omap3: Remove VMMC2 regulator on IGEP v2)
removed an unused regulator entry, but left the second MMC channel
(used by the Libertas WLAN module) without link to power regulator.
This causes the SDIO module to fail being detected.
This patch adds the two regulators that actually feed the WLAN module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected. Details of the power supply
implementation were kindly provided by Enric Balletbo i Serra.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Tested on an IGEPv2 Rev-B.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Patch "OMAP2xxx: hwmod: add I2C hwmods for OMAP2420, 2430"
in linux-next as of 20101203 introduced the following build
warning - fix this by removing the stray i2c_dev_attr.
arch/arm/mach-omap2/omap_hwmod_2430_data.c:483: warning: 'i2c_dev_attr' defined but not used
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
To support tvout on rx51,added Intilization data,
tvout as display device and enabled venc through gpio
on rx51
Signed-off-by: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Upcoming ASoC core and tlv320aic3x changes makes possible to take b part of
TLV320AIC34 into use on RX51/N900. Prepare to this by adding virtual supplies
and platform data for b part of the codec.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove second tlv320aic3x.h inclusion that came along the commit f0fba2a
"ASoC: multi-component - ASoC Multi-Component Support".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is no MFD config option, MFD_SUPPORT should be selected instead.
This will prevent build errors when trying out different configurations.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
clk_get() return value should be checked with IS_ERR(). Furthermore,
clocks should be put and disabled properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix following compilation warning:
arch/arm/mach-omap1/pm_bus.c: In function 'omap1_pm_runtime_resume':
arch/arm/mach-omap1/pm_bus.c:51: warning: unused variable 'ret'
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Patch fix following compilation warning:
arch/arm/mach-omap1/board-htcherald.c:442:
warning: large integer implicitly truncated to unsigned type
Hopefully this is just a typo.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The naming convention for omap_device is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Remove the hs prefix that is implicit for every OMAP uarts.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Govindraj Raja <govindraj.raja@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit f2ce62312650 (OMAP: WDT: Split OMAP1 and OMAP2PLUS device
registration) removed omap_init_wdt and related structures from
plat-omap/devices.c. However a subsequent commit or merge
seems to have reintroduced these by accident. The caller of
omap_init_wdt was also removed by that commit, and this did
not get restored. So we have the following build warning now:
CC arch/arm/plat-omap/devices.o
arch/arm/plat-omap/devices.c:252: warning: 'omap_init_wdt' defined but not used
Fix this by removing this dead code.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
New assemblers need -march=armv7-a+sec on command line or
.arch_extension sec inline to enable use of the smc instruction.
This patch uses as-instr to check the latter to conditionally
enable the former in AFLAGS for files that use smc.
Checked on both old and new binutils to verify that it does
not break old versions.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch will kill following section mismatch warnings:
WARNING: vmlinux.o(.text+0x24a00): Section mismatch in reference from the function zoom_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function zoom_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because zoom_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x24bfc): Section mismatch in reference from the function cm_t35_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function cm_t35_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.data+0x1d3e0): Section mismatch in reference from the variable h4_config to the (unknown reference) .init.data:(unknown)
The variable h4_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1dc08): Section mismatch in reference from the variable sdp2430_config to the (unknown reference) .init.data:(unknown)
The variable sdp2430_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1e1d8): Section mismatch in reference from the variable apollon_config to the (unknown reference) .init.data:(unknown)
The variable apollon_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE so
users will not be baffled.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add comments and IDs for the following erratas:
- i540: MPU cannot exit from Standby,
- i478: Unexpected Cold-Reset is generated when device is coming
back from OFF mode
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Add minimal support for Nokia RM-680 board.
Tested with omap2plus_defconfig.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated to remove omap_gpio_init
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Introduce 97.6/195.2 MHz memory timing data. Based on patches by Eduardo
Valentin, Igor Dmitriev and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Cc: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
41.5 MHz SDRAM clock is not usable.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Actually check for errors: print an error log and return NULL.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use an array to make it easier to add new values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rename the current timings to indicate they're for 166 MHz. Based on
patches by Eduardo Valentin and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add a header file for Nokia SDRAM functions. Based on patches by Juha
Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rename the file and functions so that it can be reused by future Nokia
boards. Based on patches by Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We need to test for 24xx not 242x. Otherwise interrupts won't work.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2: PRCM: fix some SHIFT macros that were actually bitmasks
OMAP2+: PM/serial: fix console semaphore acquire during suspend
OMAP1: SRAM: fix size for OMAP1611 SoCs
arm: omap2: io: fix clk_get() error check
arm: plat-omap: counter_32k: use IS_ERR() instead of NULL check
omap: nand: remove hardware ECC as default
omap: zoom: wl1271 slot is MMC_CAP_POWER_OFF_CARD
omap: PM debug: fix wake-on-timer debugfs dependency
|
|
Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.
Cc: stable@kernel.org
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.
At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.
All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.
This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.
Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this. These could be added later if it
matters.
Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The current implementation of the v7_coherent_*_range function assumes
that the D and I cache lines have the same size, which is incorrect
architecturally. This patch adds the icache_line_size macro which reads
the CTR register. The main loop in v7_coherent_*_range is split in two
independent loops or the D and I caches. This also has the performance
advantage that the DSB is moved outside the main loop.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The current implementation of the dcache_line_size macro reads the L1
cache size from the CCSIDR register. This, however, is not guaranteed to
be the smallest cache line in the cache hierarchy. The patch changes to
the macro to use the more architecturally correct CTR register.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Please use omap1_defconfig instead, or search online
for a more optimized defconfig for your omap1 board.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The omap1_defconfig this should be eventually usable for booting
all omap1 machines. Generated based on:
$ grep ARCH_OMAP1=y arch/arm/configs/* | cut -d: -f1 | xargs cat | \
sort | uniq >> arch/arm/configs/omap1_defconfig
Then change few things manually, like use Nokia 770 CONFIG_CMDLINE
as it does not allow setting it in the bootloader.
Finally ran make savedefconfig on it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise multi-omap1 configurations will fail.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
This way we can use the generic omap SoC detection code instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
