| Age | Commit message (Collapse) | Author |
|---|
|
memory_start symbol is needed by kernel modules.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This will ensure that kernels built with no custom CPU settings will still boot
OK on hardware that has additional CPU hardware instructions etc.
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
It is generated with longer compatible list
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Asm code uses barrel-shifter instruction that's why we have
to protect cases when HW don't have it.
Reported-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This was intended to allow manual override of CPU settings copied automatically
to Kconfig.auto, however it's problematic for several reasons, but mostly:
* If the defconfig doesn't have ALLOW_EDIT_AUTO=y, then it's impossible for
that defconfig to iverride the values in the kernel source tree. This leads
to very strange errors where the kernel is compiled with the wrong CPUFLAGS.
Next patch in the series will back out the default in Kconfig.auto to baseline
settings, so a kernel built with no default values will at least boot on any
hardware, just not make use of additional CPU features.
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Two version are generated.
linux.bin.ub which is created from linux.bin file
and
simpleImage.<dts>.ub which is created from stripped simpleImage.<dts> file
Load address and entry point is for microblaze first instruction
which is CONFIG_KERNEL_BASE_ADDR variable.
There is possible for simpleImage format parse _start symbol too.
simpleImage.<dts> is still stripped elf file
I cleared simpleImage.<dts>.unstrip file because there are so big.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
After the signal frame is set up on the userspace stack, ptrace() should
be given an opportunity to single-step into the signal handler
FRV, Blackfin, mn10300 and UM. Worth to look at that patches.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
There is missing checking agains PVR but this is not important
for now. There are some missing checking too.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
We used cache_line as cache_line_lenght. For this reason
we did cache flushing 4 times longer than was necessary.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Till this patch reset always perform writen to 1.
Now we can use negative logic and perform reset write to 0.
It is opposite level than is currently read from that pin
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
I had to change message for gpio-reset because I always
not to see it. Prefix RESET is big and visible.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Saving is done in SAVE_STATE macros that's why another save discard
previous saved value.
This change has no effect to normal programs because they ends in any exception
and they are killed. On the other side has effect on debugging.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Configuring DEBUG_SLAB causes a noMMU kernel to die during initialization
with an invalid virtual address panic in kfree_debugcheck().
The panic is due to an improper definition of pfn_valid().
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This patch add support for dynamic function graph tracer.
There is one my expactation that I can do flush_icache after
all code modification. On microblaze is this safer than do
flush for every entry. For icache is used name flush but
correct should be invalidation - this will be fix in upcomming
new cache implementaion and WB support.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
For more information look at Documentation/trace folder.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
With dynamic function tracer, by default, _mcount is defined as an
"empty" function, it returns directly without any more action. When
enabling it in user-space, it will jump to a real tracing
function(ftrace_caller), and do the real job for us.
Differ from the static function tracer, dynamic function tracer provides
two functions ftrace_make_call()/ftrace_make_nop() to enable/disable the
tracing of some indicated kernel functions(set_ftrace_filter).
In the kernel version, there is only one "_mcount" string for every
kernel function, so, we just need to match this one in mcount_regex of
scripts/recordmcount.pl.
For more information please look at code and Documentation/trace folder.
Steven ACK that scripts/recordmcount.pl part.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Implement MCOUNT_TEST in asm code - it is faster than use
generic code
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
If -pg of gcc is enabled with CONFIG_FUNCTION_TRACER=y. a calling to
_mcount will be inserted into each kernel function. so, there is a
possibility to trace the kernel functions in _mcount.
This patch add the specific _mcount support for static function
tracing. by default, ftrace_trace_function is initialized as
ftrace_stub(an empty function), so, the default _mcount will introduce
very little overhead. after enabling ftrace in user-space, it will jump
to a real tracing function and do static function tracing for us.
Commit message from Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
There are just two major changes
Renamed local_irq functions to raw_local_irq in irq.c.
Added TRACE_IRQFLAGS_SUPPORT to Kconfig.debug.
Look at Documentation/irqflags-tracing.txt
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Microblaze needs to do lock_init very soon because MMU init calls lock functions.
Here is the explanation from Peter Zijlstra why we have to enable
__ARCH_WANTS_INTERRUPTS_ON_CTSW.
"So we schedule while holding rq->lock (for obvious reasons), but since
lockdep tracks held locks per tasks, we need to transfer the held state
from the prev to the next task. We do this by explicity calling
spin_release(&rq->lock) in context_switch() right before switch_to(),
and calling spin_acquire(&rq->lock) in
finish_task_switch()->finish_lock_switch().
Now, for some reason lockdep thinks that interrupts got enabled over the
context switch (git grep __ARCH_WANTS_INTERRUPTS_ON_CTSW arch/microblaze
doesn't seem to turn up anything).
Clearly trying to acquire the rq->lock with interrupts enabled is a bad
idea and lockdep warns you about this."
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
It is the same counter as we use as free running one.
I would like to use it for ftrace.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This is working implemetation but the problem is that
Microblaze misses frame pointer that's why is there
big loop which trace and show all addresses which are in text.
It shows addresses which are in registers, etc.
This is problem and this is the reason why all Microblaze
traces are wrong. There is an option to do hacks and trace
the kernel code but this is too complicated.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
It is important for ftrace irqsoff support
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
The problem was that free_initmem pass to free_initrd_mem got
bad aligned __init_begin symbol and free_initrd_mem don't care
about __init_end but take PAGE_SIZE instead.
Here is behavior in kernel bootlog.
ramdisk_execute_command from (init/main.c) was rewrite
Freeing unused kernel memory: 6224k freed
Failed to execute ��������������{���
Failed to execute ��������������{����. Attempting defaults...
Mounting proc:
Mounting var:
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
|
|
No idea if this platform actually uses cpufreq_get(), but it doesn't
have any cpufreq drivers. That's not to say it doesn't use cpufreq_get()
in its drivers. LH7a40x is unmaintained anyhow, and should probably
be killed off.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix:
arch/arm/mach-sa1100/generic.c:117: error: redefinition of 'cpufreq_get'
include/linux/cpufreq.h:299: error: previous definition of 'cpufreq_get' was here
cpufreq_get() is used on these platforms to tell drivers what the CPU
frequency is, and therefore the bus frequency - which is critical for
setting the PCMCIA and LCD timings. Adding ifdefs to these drivers to
select cpufreq_get() or some other interface adds confusion. Making
these drivers use some other interface for the normal paths and cpufreq
stuff for the cpufreq notifier is insane as well.
(Why x86 can't provide a version of cpufreq_get() which returns the
CPU frequency when CPUFREQ is disabled is beyond me, rather than
requiring a dummy zero-returning cpufreq_get(). Especially as they
do:
unsigned long khz = cpufreq_get(cpu);
if (!khz)
khz = tsc_khz;
In other words, if CPUFREQ is disabled, get it from tsc_khz - why
not provide a dummy cpufreq_get() which returns tsc_khz?)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The power scripts optimisation was mainly done by:
Tero Kristo <tero.kristo@nokia.com> and
Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
I'm only refactoring and testing it against the mainline kernel.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
|
|
Anders Grafström reports that footbridge fails to build after 1c4a4f4.
Fix this by adding the necessary definitions for __pfn_to_bus and
__bus_to_pfn.
Reported-by: Anders Grafström <anders.grafstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When the VFP notifier is called for flush_thread(), we may be
preemptible, meaning we might migrate to another CPU, which means
referencing the current CPU number without some form of locking is
invalid, and can cause data corruption.
For the most cases, this isn't a problem since atomic notifiers are run
under rcu lock, which for most configurations results in preemption
being disabled - except when the preemptable tree-based rcu
implementation is selected.
Let's make it safe anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The Arcom Zeus CF slot requires the same kind of support as the Viper.
To avoid code duplication, introduce a platform device that abstracts
the differences.
This also allows for the removal of the ugly export of viper_cf_rst().
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Interrupt vector 0xec has been doubly defined in irq_vectors.h
It seems arbitrary whether LOCAL_PENDING_VECTOR or
UV_BAU_MESSAGE is the higher number. As long as they are
unique. If they are not unique we'll hit a BUG in
alloc_system_vector().
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
LKML-Reference: <E1NJ9Pe-0004P7-0Q@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: GTWX5715 platform only has two PCI IRQ lines, not four.
IXP4xx: Introduce IXP4XX_GPIO_IRQ(n) macro and convert IXP4xx platform files.
IXP4xx: move Gemtek GTWX5715 platform macros to the platform code.
IXP4xx: Remove unused Motorola PrPMC1100 platform macros.
IXP4xx: move FSG platform macros to the platform code.
IXP4xx: move DSM G600 platform macros to the platform code.
IXP4xx: move NAS100D platform macros to the platform code.
IXP4xx: move NSLU2 platform macros to the platform code.
IXP4xx: move Coyote platform macros to the platform code.
IXP4xx: move AVILA platform macros to the platform code.
IXP4xx: move IXDP425 platform macros to the platform code.
IXP4xx: Extend PCI MMIO indirect address space to 1 GB.
IXP4xx: Fix compilation failure with CONFIG_IXP4XX_INDIRECT_PCI.
IXP4xx: Drop "__ixp4xx_" prefix from in/out/ioread/iowrite functions for clarity.
IXP4xx: Rename indirect MMIO primitives from __ixp4xx_* to __indirect_*.
IXP4xx: Ensure index is positive in irq_to_gpio() and npe_request().
ARM: fix insl() and outsl() endianness on IXP4xx architecture.
IXP4xx: Fix normally-disabled debugging text in drivers/net/arm/ixp4xx_eth.c.
IXP4xx: change the timer base frequency to 66.666000 MHz.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (75 commits)
omap3: Fix OMAP35XX_REV macros
omap: serial: fix non-empty uart fifo read abort
omap3: Zoom2/3: Update hsmmc board config params
omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
omap3: id code detection 3525 vs 3515
omap3: rx51: Use wl1251 in SPI mode 3
omap3: zoom2/3: make MMC slot work again
omap1: htcherald: Update defconfig to include mux support
omap1: LCD_DMA: Use some define rather than a hexadecimal
omap: header: remove unused data-type
omap: arch/arm/plat-omap/devices.c - sort alphabetically
omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
OMAP3: serial - allow platforms specify which UARTs to initialize
omap3: cm-t35: add mux initialization
OMAP4: Sync up omap4430 defconfig
OMAP4: Remove the secondary wait loop
OMAP4: AuxCoreBoot registers only accessible in secure mode
OMAP4: Fix SRAM base and size
OMAP4: Fix cpu detection
omap3: pandora: board file updates for .33
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix PCI hotplug with passthrough mode
x86/amd-iommu: Fix passthrough mode
x86: mmio-mod.c: Use pr_fmt
x86: kmmio.c: Add and use pr_fmt(fmt)
x86: i8254.c: Add pr_fmt(fmt)
x86: setup_percpu.c: Use pr_<level> and add pr_fmt(fmt)
x86: es7000_32.c: Use pr_<level> and add pr_fmt(fmt)
x86: Print DMI_BOARD_NAME as well as DMI_PRODUCT_NAME from __show_regs()
x86: Factor duplicated code out of __show_regs() into show_regs_common()
arch/x86/kernel/microcode*: Use pr_fmt() and remove duplicated KERN_ERR prefix
x86, mce: fix confusion between bank attributes and mce attributes
x86/mce: Set up timer unconditionally
x86: Fix bogus warning in apic_noop.apic_write()
x86: Fix typo in arch/x86/mm/kmmio.c
x86: ASUS P4S800 reboot=bios quirk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (57 commits)
x86, perf events: Check if we have APIC enabled
perf_event: Fix variable initialization in other codepaths
perf kmem: Fix unused argument build warning
perf symbols: perf_header__read_build_ids() offset'n'size should be u64
perf symbols: dsos__read_build_ids() should read both user and kernel buildids
perf tools: Align long options which have no short forms
perf kmem: Show usage if no option is specified
sched: Mark sched_clock() as notrace
perf sched: Add max delay time snapshot
perf tools: Correct size given to memset
perf_event: Fix perf_swevent_hrtimer() variable initialization
perf sched: Fix for getting task's execution time
tracing/kprobes: Fix field creation's bad error handling
perf_event: Cleanup for cpu_clock_perf_event_update()
perf_event: Allocate children's perf_event_ctxp at the right time
perf_event: Clean up __perf_event_init_context()
hw-breakpoints: Modify breakpoints without unregistering them
perf probe: Update perf-probe document
perf probe: Support --del option
trace-kprobe: Support delete probe syntax
...
|
|
* 'for-linus' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
HTC Dream: mmc compilation fixes
video: Allow selecting MSM framebuffer in Kconfig
Add arm msm maintainer entry
msm: Add memory map for HTC Dream
msm: add minimal board file for HTC Dream device
msm: make debugging UART (for DEBUG_LL) configurable
|
|
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
|
