| Age | Commit message (Collapse) | Author |
|---|
|
regulator API
commit 49a12877d2777cadcb838981c3c4f5a424aef310 upstream.
There is currently no facility in ACPI to express the hookup of voltage
regulators, the expectation is that the regulators that exist in the
system will be handled transparently by firmware if they need software
control at all. This means that if for some reason the regulator API is
enabled on such a system it should assume that any supplies that devices
need are provided by the system at all relevant times without any software
intervention.
Tell the regulator core to make this assumption by calling
regulator_has_full_constraints(). Do this as soon as we know we are using
ACPI so that the information is available to the regulator core as early
as possible. This will cause the regulator core to pretend that there is
an always on regulator supplying any supply that is requested but that has
not otherwise been mapped which is the behaviour expected on a system with
ACPI.
Should the ability to specify regulators be added in future revisions of
ACPI then once we have support for ACPI mappings in the kernel the same
assumptions will apply. It is also likely that systems will default to a
mode of operation which does not require any interpretation of these
mappings in order to be compatible with existing operating system releases
so it should remain safe to make these assumptions even if the mappings
exist but are not supported by the kernel.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f244d8b623dae7a7bc695b0336f67729b95a9736 upstream.
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* acpi-assorted:
ACPI / osl: Kill macro INVALID_TABLE().
earlycpio.c: Fix the confusing comment of find_cpio_data().
ACPI / x86: Print Hot-Pluggable Field in SRAT.
ACPI / thermal: Use THERMAL_TRIPS_NONE macro to replace number
ACPI / thermal: Remove unused macros in the driver/acpi/thermal.c
ACPI / thermal: Remove the unused lock of struct acpi_thermal
ACPI / osl: Fix osi_setup_entries[] __initdata attribute location
ACPI / numa: Fix __init attribute location in slit_valid()
ACPI / dock: Fix __init attribute location in find_dock_and_bay()
ACPI / Sleep: Fix incorrect placement of __initdata
ACPI / processor: Fix incorrect placement of __initdata
ACPI / EC: Fix incorrect placement of __initdata
ACPI / scan: Drop unnecessary label from acpi_create_platform_device()
ACPI: Move acpi_bus_get_device() from bus.c to scan.c
ACPI / scan: Allow platform device creation without any IO resources
ACPI: Cleanup sparse warning on acpi_os_initialize1()
platform / thinkpad: Remove deprecated hotkey_report_mode parameter
ACPI: Remove the old /proc/acpi/event interface
|
|
Move acpi_bus_get_device() from bus.c to scan.c which allows
acpi_bus_data_handler() to become static and clean up the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch cleans up the following sparse warning:
# make C=2 drivers/acpi/osl.o
...
drivers/acpi/osl.c:1775:20: warning: symbol 'acpi_os_initialize1' was not declared. Should it be static?
...
CC drivers/acpi/osl.o
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is quite some time that this one has been deprecated.
Get rid of it.
Should some really important user be overseen, it may be reverted and
the userspace program worked on first, but it is time to do something
to get rid of this old stuff...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are no users of the ACPI bus notifier call chain,
acpi_bus_notify_list, any more, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce helper function acpi_execute_simple_method() and use it in
a number of places to simplify code.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
These local variables are all initialized at their first use, so there's
no point in initializing them earlier.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Replace the combination of kmalloc() and memcpy() in acpi_run_osc()
with a single call to kmemdup().
[rjw: Changelog]
Signed-off-by: Andrei Epure <epure.andrei@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Move ACPI device power management functions from drivers/acpi/bus.c
to drivers/acpi/device_pm.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function returning string representations of ACPI device power
states, state_string((), is now static, because it is only used
internally in drivers/acpi/bus.c. However, it will be used outside
of that file going forward, so rename it to
acpi_power_state_string(), add a kerneldoc comment to it and add its
header to acpi_bus.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function used for retrieving ACPI device power states,
__acpi_bus_get_power(), is now static, because it is only used
internally in drivers/acpi/bus.c. However, it will be used
outside of that file going forward, so rename it to
acpi_device_get_power(), in analogy with acpi_device_set_power(),
add a kerneldoc comment to it and add its header to acpi_bus.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
During power transitions into D3cold from any shallower power states
we are supposed to transition the device into D3hot and remove power
from it afterward, but the current code in acpi_device_set_power()
doesn't work this way.
At the same time, though, we need to be careful enough to preserve
backwards compatibility for systems that don't distinguish between
D3hot and D3cold (e.g. designed before ACPI 4).
Modify acpi_device_set_power() so that it works in accordance with
the expectations in both cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
No power transitioning from D3 state up to a non-D0 state is allowed
so make acpi_device_set_power() fail and complain if such a transition
is attempted.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the caller of acpi_bus_set_power() already has a pointer to the
struct acpi_device object corresponding to the device in question, it
doesn't make sense for it to go through acpi_bus_get_device(), which
may be costly, because it involves acquiring the global ACPI
namespace mutex.
For this reason, export the function operating on struct acpi_device
objects used internally by acpi_bus_set_power(), so that it may be
called instead of acpi_bus_set_power() in the above case, and change
its name to acpi_device_set_power().
Additionally, introduce two inline wrappers for checking ACPI PM
capabilities of devices represented by struct acpi_device objects.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The _OSC method may exist in module level code,
so it must be called after ACPI_FULL_INITIALIZATION
On some new platforms with Zero-Power-Optical-Disk-Drive (ZPODD)
support, this fix is necessary to save power.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
|
|
It turns out that there are ACPI BIOSes defining device objects with
_PSx and without either _PSC or _PRx. For devices corresponding to
those ACPI objetcs __acpi_bus_get_power() returns ACPI_STATE_UNKNOWN
and their initial power states are regarded as unknown as a result.
If such a device is a parent of another power-manageable device, the
child cannot be put into a low-power state through ACPI, because
__acpi_bus_set_power() refuses to change power states of devices
whose parents' power states are unknown.
To work around this problem, observe that the ACPI power state of
a device cannot be higher-power (lower-number) than the power state
of its parent. Thus, if the device's _PSC method or the
configuration of its power resources indicates that the device is
in D0, the device's parent has to be in D0 as well. Consequently,
if the parent's power state is unknown when we've just learned that
its child's power state is D0, we can safely set the parent's
power.state field to ACPI_STATE_D0.
Tested-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
'cpuidle-coupled', 'cpuidle-tweaks', 'intel_idle-ivb', 'ost', 'red-hat-bz-772730', 'thermal', 'thermal-spear' and 'turbostat-v2' into release
|
|
When ACPI_HOTPLUG_OST is defined, set hotplug _OST support bit
OSC_SB_HOTPLUG_OST_SUPPORT to indicate that the OS supports hotplug
_OST by calling the platform-wide ACPI Operating System Capabilities
(_OSC).
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
After recent changes of the ACPI device power states definitions, if
power resources are not used for the device's power management, the
state returned by __acpi_bus_get_power() cannot exceed D3hot, because
the return values of _PSC are 0 through 3. However, if the _PR3
method is not present for the device and _PS3 returns 3, we have to
assume that the device is in D3cold, so the value returned by
__acpi_bus_get_power() in that case should be 4.
Similarly, acpi_power_get_inferred_state() should take the power
resources for the D3hot state into account in general, so that it
can return 3 if those resources are "on" or 4 (D3cold) otherwise.
Fix the the above two issues and make sure that if both _PSC and
_PR3 are present for the device, the power resources listed by _PR3
will be used to determine if the number 3 returned by _PSC is meant
to represent D3cold or D3hot.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
After recent changes of the ACPI device low-power states definitions
kernel messages in drivers/acpi/bus.c need to be updated so that they
include the correct names of the states in question (currently is
"D3" for D3hot and "D4" for D3cold, which is incorrect).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit 1cc0c998fdf2 ("ACPI: Fix D3hot v D3cold confusion") introduced a
bug in __acpi_bus_set_power() and changed the behavior of
acpi_pci_set_power_state() in such a way that it generally doesn't work
as expected if PCI_D3hot is passed to it as the second argument.
First off, if ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) is passed to
__acpi_bus_set_power() and the explicit_set flag is set for the D3cold
state, the function will try to execute AML method called "_PS4", which
doesn't exist.
Fix this by adding a check to ensure that the name of the AML method
to execute for transitions to ACPI_STATE_D3_COLD is correct in
__acpi_bus_set_power(). Also make sure that the explicit_set flag
for ACPI_STATE_D3_COLD will be set if _PS3 is present and modify
acpi_power_transition() to avoid accessing power resources for
ACPI_STATE_D3_COLD, because they don't exist.
Second, if PCI_D3hot is passed to acpi_pci_set_power_state() as the
target state, the function will request a transition to
ACPI_STATE_D3_HOT instead of ACPI_STATE_D3. However,
ACPI_STATE_D3_HOT is now only marked as supported if the _PR3 AML
method is defined for the given device, which is rare. This causes
problems to happen on systems where devices were successfully put
into ACPI D3 by pci_set_power_state(PCI_D3hot) which doesn't work
now. In particular, some unused graphics adapters are not turned
off as a result.
To fix this issue restore the old behavior of
acpi_pci_set_power_state(), which is to request a transition to
ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) if either PCI_D3hot or
PCI_D3cold is passed to it as the argument.
This approach is not ideal, because generally power should not
be removed from devices if PCI_D3hot is the target power state,
but since this behavior is relied on, we have no choice but to
restore it at the moment and spend more time on designing a
better solution in the future.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43228
Reported-by: rocko <rockorequin@hotmail.com>
Reported-by: Cristian Rodríguez <crrodriguez@opensuse.org>
Reported-and-tested-by: Peter <lekensteyn@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Drivers may wish to add entries to /sys/firmware/acpi, so export acpi_kobj
in order to let them do that.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ACPI_NO_HARDWARE_INIT is only used by acpi_early_init() and
acpi_bus_init() when calling acpi_enable_subsystem(), but
acpi_enable_subsystem() doesn't check that flag, so it can be
dropped.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
as GHES is optional...
When # CONFIG_ACPI_APEI_GHES is not set:
(.init.text+0x4c22): undefined reference to `ghes_disable'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
In APEI firmware first mode, hardware error is reported by hardware to
firmware firstly, then firmware reports the error to Linux in a GHES
error record via POLL/SCI/IRQ/NMI etc.
This may result in some issues if OS has no full APEI support. So
some firmware implementation will work in a back-compatible mode by
default. Where firmware will only notify OS in old-fashion, without
GHES record. For example, for a fatal hardware error, only NMI is
signaled, no GHES record.
To gain full APEI power on these machines, APEI bit in generic _OSC
call can be specified to tell firmware that Linux has full APEI
support. This patch adds the APEI bit support in generic _OSC call.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
_SxW returns an Integer containing the lowest D-state supported in state
Sx. If OSPM has not indicated that it supports _PR3, then the value “3”
corresponds to D3. If it has indicated _PR3 support, the value “3”
represents D3hot and the value “4” represents D3cold.
Linux does set _OSC._PR3, so we should fix it to expect that _SxW can
return 4.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The variable pm_flags is used to prevent APM from being enabled
along with ACPI, which would lead to problems. However, acpi_init()
is always called before apm_init() and after acpi_init() has
returned, it is known whether or not ACPI will be used. Namely, if
acpi_disabled is not set after acpi_init() has returned, this means
that ACPI is enabled. Thus, it is sufficient to check acpi_disabled
in apm_init() to prevent APM from being enabled in parallel with
ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
|
|
If direct references to pm_flags are removed from drivers/acpi/bus.c,
CONFIG_ACPI will not need to depend on CONFIG_PM any more. Make that
happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
|
|
Since acpi_bus_set_power() should not use __acpi_bus_get_power() to
update the device's device->power.state field before changing its
power state (this may cause device->power.state to be inconsistent
with the device power resources' reference counters), remove this
call from it. In consequence, the acpi_power_nocheck variable is not
necessary any more, so it can be dropped along with the DMI table
used for setting that variable for HP Pavilion 05.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There are no more users of acpi_bus_get_power(), so it can be
dropped. Moreover, it should be dropped, because it modifies
the device->power.state field of an ACPI device without updating
the reference counters of the device's power resources, which is
wrong.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use the new function acpi_bus_update_power() for manipulating power
resources used by ACPI fan devices, which allows them to be put into
the right state during initialization and resume. Consequently,
remove the flags.force_power_state field from struct acpi_device,
which is not necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The ACPI device driver used for handling power resources,
acpi_power_driver, creates a struct acpi_power_resource object for
each ACPI device representing a power resource. These objects are
then used when setting and reading the power states of devices using
the corresponding power resources. Unfortunately, acpi_power_driver
is registered after acpi_scan_init() that may add devices using the
power resources before acpi_power_driver has a chance to create
struct acpi_power_resource objects for them (specifically, the power
resources may be referred to during the scanning process through
acpi_bus_get_power() before they have been initialized).
As the first step towards fixing this issue, move the registration
of acpi_power_driver into acpi_scan_init() so that power resource
devices can be initialized by it as soon as they have been found in
the namespace.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add function acpi_bus_update_power() for reading the actual power
state of an ACPI device and updating its device->power.state field
in such a way that its power resources' reference counters will
remain consistent with that field.
For this purpose introduce __acpi_bus_set_power() setting the
power state of an ACPI device without updating its
device->power.state field and make acpi_bus_set_power() and
acpi_bus_update_power() use it (acpi_bus_set_power() retains the
current behavior for now).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add function acpi_bus_init_power() for getting the initial power
state of an ACPI device and reference counting its power resources
as appropriate.
Make acpi_bus_get_power_flags() use the new function instead of
acpi_bus_get_power() that updates device->power.state without
reference counting the device's power resources.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
It sometimes is necessary to get the power state of an ACPI device
without updating its device->power.state field, for example to
avoid inconsistencies between device->power.state and the reference
counters of the device's power resources. For this purpose introduce
__acpi_bus_get_power() that will return the given device's power
state via a pointer (instead of modifying device->power.state)
and make acpi_bus_get_power() use it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
acpi_power_get_inferred_state() should not update
device->power.state behind the back of its caller, so make it return
the state via a pointer instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ACPI table sysfs I/F is broken by commit
78f1699659963fff97975df44db6d5dbe7218e55
Author: Alex Chiang <achiang@hp.com>
Date: Sun Dec 20 12:19:09 2009 -0700
ACPI: processor: call _PDC early
because dynamic SSDT tables may be loaded in _PDC,
before installing the ACPI table handler.
As a result, the sysfs I/F of these dynamic tables are
located at /sys/firmware/acpi/tables instead of
/sys/firmware/acpi/tables/dynamic, which is not true.
Invoke acpi_sysfs_init() before acpi_early_processor_set_pdc(),
so that the table handler is installed before any dynamic tables loaded.
https://bugzilla.kernel.org/show_bug.cgi?id=21142
CC: Dennis Jansen <dennis.jansen@web.de>
CC: Alex Chiang <achiang@hp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
'bugzilla-14736', 'bugzilla-14679', 'bugzilla-16396', 'launchpad-613381' and 'misc' into release
|
|
Our list of Toshiba Satellite models that require this workaround
is growing -- so invoke the workaround for the entire product line.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Rmove deprecated ACPI procfs I/F, including
/proc/acpi/debug_layer
/proc/acpi/debug_level
/proc/acpi/info
/proc/acpi/dsdt
/proc/acpi/fadt
/proc/acpi/sleep
because the sysfs I/F is already available
and has been working well for years.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Introduce drivers/acpi/sysfs.c.
code for ACPI sysfs I/F, including
#ifdef ACPI_DEBUG
/sys/module/acpi/parameters/debug_layer
/sys/module/acpi/parameters/debug_level
/sys/module/acpi/parameters/trace_method_name
/sys/module/acpi/parameters/trace_debug_layer
/sys/module/acpi/parameters/trace_debug_level
/sys/module/acpi/parameters/trace_state
#endif
/sys/module/acpi/parameters/acpica_version
/sys/firmware/acpi/tables/
/sys/firmware/acpi/interrupts/
is moved to this file.
No function change in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Introduce drivers/acpi/debugfs.c.
Code for ACPI debugfs I/F,
i.e. /sys/kernel/debug/acpi/custom_method,
is moved to this file.
And make ACPI debugfs always built in,
even if CONFIG_ACPI_DEBUG is cleared.
BTW:this adds about 400bytes code to ACPI, when
CONFIG_ACPI_DEBUG is cleared.
[uaccess.h build fix from Andrew Morton <akpm@linux-foundation.org>]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove own implementation of hex_to_bin().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (22 commits)
ACPI: fix early DSDT dmi check warnings on ia64
ACPICA: Update version to 20100428.
ACPICA: Update/clarify some parameter names associated with acpi_handle
ACPICA: Rename acpi_ex_system_do_suspend->acpi_ex_system_do_sleep
ACPICA: Prevent possible allocation overrun during object copy
ACPICA: Split large file, evgpeblk
ACPICA: Add GPE support for dynamically loaded ACPI tables
ACPICA: Clarify/rename some root table descriptor fields
ACPICA: Update version to 20100331.
ACPICA: Minimize the differences between linux GPE code and ACPICA code base
ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT
ACPICA: Update DSDT copy/detection.
ACPICA: Add subsystem option to force copy of DSDT to local memory
ACPICA: Add detection of corrupted/replaced DSDT
ACPICA: Add write support for DataTable operation regions
ACPICA: Fix for acpi_reallocate_root_table for incorrect root table copy
ACPICA: Update comments/headers, no functional change
ACPICA: Update version to 20100304
ACPICA: Fix for possible fault in acpi_ex_release_mutex
ACPICA: Standardize integer output for ACPICA warnings/errors
...
|
|
WARNING: at drivers/firmware/dmi_scan.c:423 dmi_matches+0x70/0x160()
dmi check: not initialized yet.
This is caused by commit aa2110c
(ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT).
DMI is not initialized yet in acpi_early_init on ia64.
The DSDT DMI check table is x86 specific, so make it empty on other archs.
And this fixes the warnings on ia64.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This addresses: https://bugzilla.kernel.org/show_bug.cgi?id=14998
We copy some strings into "event" but we leave the space after the NULL
terminators uninitialized. Later in acpi_bus_receive_event() we copy
the whole struct to another buffer with memcpy(). If the new buffer is
stored on the stack, kmemcheck prints a warning about the unitialized
space after the NULL terminators.
It's true that the space is uninitialized, but it's harmless. The
buffer is only used in acpi_system_read_event() and we don't read past
the NULL terminators.
This patch changes the kmalloc() to kzalloc() so that we initialize the
memory and silence the kmemcheck warning.
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some BIOS on Toshiba machines corrupt the DSDT, so add a new
boot option acpi=copy_dsdt to workaround it.
Add warning message to ask users to use this option if corrupt DSDT detected.
Also build a DMI blacklist to check it and automatically copy DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
