| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver has both SPI and I2C pieces. The appropriate pieces are built based
on whether SPI and/or I2C is/are enabled. However, it was only checking if I2C
was built-in, never if it was built as a module. This patch checks for either
since building both this driver and I2C as modules is possible.
Signed-off-by: Daniel M. Weeks <dan@danweeks.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pullups are enabled when bits are set, not when cleared.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in gpio
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Add i2c bindings for the mcp230xx devices. This is quite a lot simpler
than the spi one as there's no funky sub addressing done (one struct
i2c_client per struct gpio_chip).
The mcp23s08_platform_data structure is reused for i2c, even though
only a single mcp23s08_chip_info structure is needed.
To use, simply fill out a platform_data structure and pass it in
i2c_board_info, E.G.:
static const struct mcp23s08_platform_data mcp23017_data = {
.chip[0] = {
.pullups = 0x00ff,
},
.base = 240,
};
static struct i2c_board_info __initdata i2c_devs[] = {
{ I2C_BOARD_INFO("mcp23017", 0x20),
.platform_data = &smartview_mcp23017_data, },
...
};
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Change spi member of struct mcp23s08 to be a ops-specific opaque data
pointer, and move spi specific knowledge out of mcp23s08_probe_one().
No functional change, but is needed to add i2c support.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
There's no in-tree users, and bus notifiers are more generic anyway.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Never accessed anywhere.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.
v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
