| Age | Commit message (Collapse) | Author |
|---|
|
The main/spare areas are on different addresses on later versions
of the controller, so make them configurable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Instead of having two switch/case with other operations
in between, use only one switch/case
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The NAND controller has some limitations how to access the
internal buffers. It only allows 32 bit accesses. The driver
used to work around this by having special alignment aware
copy routines.
We now copy the whole page to a buffer in memory and let the
access functions use this buffer. This simplifies the driver.
A bonnie++ test showed that this has no negative performance
impact on the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This factors the address cycle to a seperate function. This
becomes useful in a later patch where we can simplify the
command processing by making use of this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The oob layout was initialized several times. Instead, use
a smallpage layout by default and switch to a largepage
afterwards if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The original Freescale driver used to have eccoob descriptions like
this:
static struct nand_ecclayout nand_hw_eccoob_8 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 5}, {11, 5}}
};
static struct nand_ecclayout nand_hw_eccoob_16 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 6}, {12, 4}}
};
The former was used for 8bit flashes and the latter for 16bit flashes.
They honored the fact that the bad block marker on 8bit flashes is on byte 5
while on 16bit flashes it is on byte 11.
In the Kernel driver this was copied wrong and we ended up with two identical
descriptions.
Change it so that we have only one description which leaves byte 5 and byte
11 unspecified so that it won't be used by others.
Also, rename the descriptions to nand_hw_eccoob_smallpage and
nand_hw_eccoob_largepage so that it can't be confused with Nand chip bus
widths (what actually happened in this driver)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This reverts commit 71b7d0d90d536ae4e70929cc59a1a9f6ba457c6c.
The problem which that commit attempted to fix was a bootloader issue,
which had been misunderstood. The 'fix' causes lots of false bad blocks
for existing users with sane firmware.
Thanks to Mathieu Berland for diagnosing the problem coherently.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add a request_mem_region() before doing the ioremap(). Also, use the
resource_size macro instead of doing the end - start + 1 calc by hand.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The function mxcnd_remove is used only wrapped by __exit_p so define it
using __exit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vladimir Barinov <vova.barinov@gmail.com>
Cc: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Unused variable "eccpos" removed from atmel_nand driver.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Correct typo to use mask_ale from platform data when set to non-zero.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fixed following htmldocs warnings:
DOCPROC Documentation/DocBook/mtdnand.xml
Warning(drivers/mtd/nand/nand_base.c:769): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:785): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:824): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:947): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:996): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:1040): No description found for parameter 'page'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
|
|
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/mtd/mtdcore.c
Merged in order that I can apply the Nomadik nand/onenand support patches.
|
|
As with orion_nand in commit f33dabbe79fdf7a8568c65faa1db7794c87ac4d3
("register orion_nand using platform_driver_probe()"), avoid .init.text
problems by using platform_device_probe(). This isn't going to be
hotplugged anyway.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Using __nand_correct_data() helper function, this driver can read 512
byte (with 6 byte ECC) at a time. This results minor performance
improvement.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This driver may be reading 512 bytes at a times, but still calculates
256-byte sector ECC. So the nand_correct_data() is not appropriate
for this driver. Implement its ecc.correct function calling
__nand_correct_data() twice.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Split nand_correct_data() into two part, a pure calculation function
and a wrapper for mtd interface.
The tmio_nand driver can implement its ecc.correct function easily
using this __nand_correct_data helper.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fix ECC Correction bug where the byte offset location were double
fliped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the b1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byte_addr = (addressbits[b1] << 4) + addressbits[b0];
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Cc: stable@kernel.org
Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds DMA mode support for nand prefetch/post-write engine.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add w90p910 NAND driver for w90p910 evaluation board
based on w90p910,there is a K8F1G08 NAND on my board.
[dwmw2: depend on MTD_PARTITIONS]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Yeasah Pell <yeasah@comrex.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch allows i.MX27 to support 2KiB pagesize NAND flash.
We are using a 1.8V NAND flash which datasheet (unfortunately only
available under NDA) says :
Page size: x8: 2,112 bytes (2,048 + 64 bytes).
Without this patch, all sectors are marked as bad eraseblock.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by : Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds 4-bit ECC support for large page NAND chips using the new
ECC mode NAND_ECC_HW_OOB_FIRST. The platform data from board-dm355-evm
has been adjusted to use this mode.
The patches have been verified on DM355 device with 2KiB-page Micron
devices using mtd-tests and JFFS2. Error correction up to 4 bits has
also been verified using nandwrite/nanddump utilities.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2KiB) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
"ECC_HW_OOB_FIRST" name suggested by Thomas Gleixner
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
orion_nand_probe lives in .init.text, so using platform_driver_register to
register it is wrong because binding a device after the init memory is
discarded (e.g. via sysfs) results in an oops.
As requested by Nicolas Pitre platform_driver_probe is used instead of
moving the probe function to .devinit.text as proposed initially. This
saves some memory, but devices registered after the driver is probed are
not bound (probably there are none) and binding via sysfs isn't possible.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Joern Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (47 commits)
OMAP clock: use debugfs_remove_recursive() for rewinding
OMAP2/3/4 core: create omap_device layer
OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
OMAP2/3/4: create omap_hwmod layer
OMAP2/3 board-*.c files: read bootloader configuration earlier
OMAP2/3/4 PRCM: add module IDLEST wait code
OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
OMAP clock: associate MPU clocks with the mpu_clkdm
OMAP3 clock: Fixed processing of bootarg 'mpurate'
OMAP: SDRC: Add several new register definitions
OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
OMAP: PM: Added suspend target state control to debugfs for OMAP3
OMAP: PM debug: Add PRCM register dump support
OMAP: PM debug: make powerdomains use PM-debug counters
OMAP: PM: Add pm-debug counters
OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
OMAP: PM: Hook into PM counters
OMAP: PM counter infrastructure.
OMAP3: PM: fix lockdep warning caused by omap3_pm_init
...
|
|
|
|
'w90x900' into devel
|
|
This patch allows core driver to choose ECC block size in
sw ecc case.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
1. <linux/io.h> should be included not <asm/io.h>
2. add platform specific header <mach/ts72xx.h>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Correcting debug prints by removing function names from print messages
and using '__func__' macro instead.
Function names were wrong in few places.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Singed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Rename OMAP_MPUIO_BASE to OMAP1_MPUIO_BASE
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GCC 4.3.3 and 4.4.1 happily moves the dword load instruction out of the
loop in orion_nand_read_buf. This patch makes the instruction volatile
to avoid the issue. I've discussed this at gcc-help, refer to the thread
at
http://gcc.gnu.org/ml/gcc-help/2009-08/msg00187.html
The early clobber is added to avoid the destination registers and the
source register overlapping.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
arch/arm/mach-ep93xx/include/mach/hardware.h
1. Properly name the include files so that they are loaded
from the <mach/*> directory and not the local directory.
2. Remove including the ts72xx.h header. This header is not
generic to the ep93xx platform. It should only be included
by the ts72xx specific files that require it. The only
two users in the tree are arch/arm/mach-ep93xx/ts72xx.c
and drivers/mtd/nand/ts7250.c.
arch/arm/mach-ep93xx/include/mach/ts72xx.h
1. <linux/io.h> should already be included by any user of this
header. Doing the include here hides it from being needed
by the calling source file.
arch/arm/mach-ep93xx/core.c
1. Remove unnecessary headers. They were probably included
originally due to cut-and-paste from other files.
2. <linux/io.h> should be included not <mach/gpio.h>
arch/arm/mach-ep93xx/adsphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
2. Add platform specific header <mach/ts72xx.h>.
drivers/mtd/nand/ts7250.c
1. <linux/io.h> should be included not <asm/io.h>.
2. Add platform specific header <mach/ts72xx.h>.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We need to include jiffies.h manually in some cases, and the status
returned from omap_wait() was broken in two separate ways.
Also add cond_resched() to the loop.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
|
