Age | Commit message (Collapse) | Author |
|
commit f244d8b623dae7a7bc695b0336f67729b95a9736 upstream.
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f26ca1d699e8b54a50d9faf82327d3c2072aaedd upstream.
acpiphp_enumerate_slots() walks ACPI namenamespace under
a PCI host bridge with callback register_slot().
register_slot() evaluates _ADR for all the device objects
and emits a warning message for any error. Some platforms
have _HID device objects (such as HPET and IPMI), which
trigger unnecessary warning messages.
This patch avoids emitting a warning message when a target
device object does not have _ADR.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fc9bbf98fd66f879e628d8537ba7c240be2b58e upstream.
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c2332 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7cc5cf74544d97d7b69e2701595037474db1f96 upstream.
The pcie_portdrv .probe() method calls pci_enable_device() once, in
pcie_port_device_register(), but the .remove() method calls
pci_disable_device() twice, in pcie_port_device_remove() and in
pcie_portdrv_remove().
That causes a "disabling already-disabled device" warning when removing a
PCIe port device. This happens all the time when removing Thunderbolt
devices, but is also easy to reproduce with, e.g.,
"echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind"
This patch removes the disable from pcie_portdrv_remove().
[bhelgaas: changelog, tag for stable]
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 2dc4128 (ACPI / hotplug / PCI: Avoid doing too much for
spurious notifies) changed the enable_slot() to check return value of
pci_scan_slot() and if it is zero return early from the function. It
means that there were no new devices in this particular slot.
However, if a device appeared deeper in the hierarchy the code now
ignores it causing things like Thunderbolt chaining fail to recognize
new devices.
The problem with Alex Williamson's machine was solved with commit
a47d8c8 (ACPI / hotplug / PCI: Avoid parent bus rescans on spurious
device checks) and hence we should be able to restore the original
functionality that we always rescan on bus check notification.
On a device check notification we still check what acpiphp_rescan_slot()
returns and on zero bail out early.
Fixes: 2dc41281b1d1 (ACPI / hotplug / PCI: Avoid doing too much for spurious notifies)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The WARN_ON() in acpiphp_enumerate_slots() triggers unnecessarily for
devices whose bridges are going to be handled by native PCIe hotplug
(pciehp) and the simplest way to prevent that from happening is to
drop the WARN_ON().
References: https://bugzilla.kernel.org/show_bug.cgi?id=62831
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
One of the error code paths in acpiphp_enumerate_slots() is missing
a pci_dev_put(bridge->pci_dev) call, so add it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Ben Herrenschmidt found that commit 928bea964827 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.
The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.
Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.
Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.
That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 448bd85 (PCI/PM: add PCIe runtime D3cold support) added a
piece of code to pci_acpi_wake_dev() causing that function to behave
in a special way for devices in D3cold (so that their configuration
registers are not accessed before those devices are resumed).
However, it didn't take the clearing of the pme_poll flag into
account. That has to be done for all devices, even if they are in
D3cold, or pci_pme_list_scan() will not know that wakeup has been
signaled for the device and will poll its PME Status bit
unnecessarily.
Fix the problem by moving the clearing of the pme_poll flag in
pci_acpi_wake_dev() before the code introduced by commit 448bd85.
Reported-and-tested-by: David E. Box <david.e.box@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.6+ <stable@vger.kernel.org> # 3.6+
|
|
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"All of these commits are fixes that have emerged recently and some of
them fix bugs introduced during this merge window.
Specifics:
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting
breakage on a system that triggers device check notifications
during boot for non-existing devices. Although those
notifications are really spurious, we should be able to deal with
them nevertheless and that shouldn't introduce too much overhead.
Four commits to make that work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the
information expected by the driver. Fix from Mika Westerberg, for
stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice).
From Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one
that the BIOS expects us to choose, so this makes the lookup take
more criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with
cpufreq related to CPU hotplug which are addressed by a series of
fixes from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state
won't work correcty if cputime_t doesn't map directly to jiffies.
Fix from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency
problems in cpufreq related to the ordering of transitions, but
unfortunately it introduced several problems of its own, so I
decided to revert it now and address the original problems later
in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs
attributes over suspend/resume cycles introduced a possible NULL
pointer dereference that caused it to crash during the second
attempt to suspend. Three commits from Srivatsa S Bhat fix that
problem and a couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu"
* tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
cpufreq: Acquire the lock in cpufreq_policy_restore() for reading
cpufreq: Prevent problems in update_policy_cpu() if last_cpu == new_cpu
cpufreq: Restructure if/else block to avoid unintended behavior
cpufreq: Fix crash in cpufreq-stats during suspend/resume
intel_pstate: Add Haswell CPU models
Revert "cpufreq: make sure frequency transitions are serialized"
cpufreq: Use signed type for 'ret' variable, to store negative error values
cpufreq: Remove temporary fix for race between CPU hotplug and sysfs-writes
cpufreq: Synchronize the cpufreq store_*() routines with CPU hotplug
cpufreq: Invoke __cpufreq_remove_dev_finish() after releasing cpu_hotplug.lock
cpufreq: Split __cpufreq_remove_dev() into two parts
cpufreq: Fix wrong time unit conversion
cpufreq: serialize calls to __cpufreq_governor()
cpufreq: don't allow governor limits to be changed when it is disabled
ACPI / bind: Prefer device objects with _STA to those without it
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPICA: Fix for a Store->ArgX when ArgX contains a reference to a field.
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
...
|
|
* acpi-pci-hotplug:
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
|
|
In the current ACPIPHP notify handler we always go directly for a
rescan of the parent bus if we get a device check notification for
a device that is not a bridge. However, this obviously is
overzealous if nothing really changes, because this way we may rescan
the whole PCI hierarchy pretty much in vain.
That happens on Alex Williamson's machine whose ACPI tables contain
device objects that are supposed to coresspond to PCIe root ports,
but those ports aren't physically present (or at least they aren't
visible in the PCI config space to us). The BIOS generates multiple
device check notifies for those objects during boot and for each of
them we go straight for the parent bus rescan, but the parent bus is
the root bus in this particular case. In consequence, we rescan the
whole PCI bus from the top several times in a row, which is
completely unnecessary, increases boot time by 50% (after previous
fixes) and generates excess dmesg output from the PCI subsystem.
Fix the problem by checking if we can find anything new in the
slot corresponding to the device we've got a device check notify
for and doing nothig if that's not the case.
The spec (ACPI 5.0, Section 5.6.6) appears to mandate this behavior,
as it says:
Device Check. Used to notify OSPM that the device either appeared
or disappeared. If the device has appeared, OSPM will re-enumerate
from the parent. If the device has disappeared, OSPM will
invalidate the state of the device. OSPM may optimize out
re-enumeration.
Therefore, according to the spec, we are free to do nothing if
nothing changes.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60865
Reported-and-tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The spec suggests that we should use _OST to notify the platform
about the status of notifications it sends us, for example so that
it doesn't repeate a notification that has been handled already.
This turns out to help reduce the amount of diagnostic output from
the ACPIPHP subsystem and speed up boot on at least one system that
generates multiple device check notifies for PCIe devices on the root
bus during boot.
Reported-and-tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Sometimes we may get a spurious device check or bus check notify for
a hotplug device and in those cases we should avoid doing all of the
configuration work needed when something actually changes. To that
end, check the return value of pci_scan_slot() in enable_slot() and
bail out early if it is 0.
This turns out to help reduce the amount of diagnostic output from
the ACPIPHP subsystem and speed up boot on at least one system that
generates multiple device check notifies for PCIe devices on the root
bus during boot.
Reported-and-tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
|
|
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
|
|
In acpiphp_bus_add() we first remove device objects corresponding to
the given handle and the ACPI namespace branch below it, which are
then re-created by acpi_bus_scan(). This used to be done to clean
up after surprise removals, but now we do the cleanup through
trim_stale_devices() which checks if the devices in question are
actually gone before removing them, so the device hierarchy trimming
in acpiphp_bus_add() is not necessary any more and, moreover, it may
lead to problems if it removes device objects corresponding to
devices that are actually present.
For this reason, remove the leftover acpiphp_bus_trim() from
acpiphp_bus_add().
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
* tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (217 commits)
cpufreq: Don't use smp_processor_id() in preemptible context
cpuidle: coupled: fix race condition between pokes and safe state
cpuidle: coupled: abort idle if pokes are pending
cpuidle: coupled: disable interrupts after entering safe state
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
cpufreq: governor: Fix typos in comments
cpufreq: governors: Remove duplicate check of target freq in supported range
cpufreq: Fix timer/workqueue corruption due to double queueing
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
cpufreq: imx6q: Fix clock enable balance
ACPI: blacklist win8 OSI for buggy laptops
cpufreq: tegra: fix the wrong clock name
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
...
|
|
Add an arch specific attribute to recover a pci function from an
error state or config space blockage.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Convert s390' pci hotplug to be builtin only, with no module option.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
* pci/misc:
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
|
|
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
Error-handling code was manually removed from the associated calls to
platform_get_resource.
Adjust the comment at the third platform_get_resource_byname to make clear
why ioremap is not done at this point.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds wrappers for MMIO access to ELBI, PHY, and other
registers. No functional change.
[bhelgaas: changelog]
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
The "dbi_addr" argument to dw_pcie_readl_rc() and dw_pcie_writel_rc()
is redundant and misleading because we always have the "struct pcie_port"
and we always want to use the address from there.
This patch removes the argument and changes the callers to match.
No functional change.
[bhelgaas: changelog]
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
* pci/misc:
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
|
|
pcie_cap_has_devctl() does nothing, so remove it. Simplicity over
consistency in this case. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
Previously we allowed callers to access Slot Capabilities, Status, and
Control for Root Ports even if the Root Port did not implement a slot.
This seems dubious because the spec only requires these registers if a
slot is implemented.
It's true that even Root Ports without slots must have *space* for these
slot registers, because the Root Capabilities, Status, and Control
registers are after the slot registers in the capability. However,
for a v1 PCIe Capability, the *semantics* of the slot registers are
undefined unless a slot is implemented.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
Previously we relied on the PCIe r3.0, sec 7.8, spec language that says
"For Functions that do not implement the [Link, Slot, Root] registers,
these spaces must be hardwired to 0b," which means that for v2 PCIe
capabilities, we don't need to check the device type at all.
But it's simpler if we don't need to check the capability version at all,
and I think the spec is explicit enough about which registers are required
for which types that we can remove the version checks.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
Every PCIe device has a link, except Root Complex Integrated Endpoints
and Root Complex Event Collectors. Previously we didn't give access
to PCIe capability link-related registers for Upstream Ports, Downstream
Ports, and Bridges, so attempts to read PCI_EXP_LNKCTL incorrectly
returned zero. See PCIe spec r3.0, sec 7.8 and 1.3.2.3.
Reference: http://lkml.kernel.org/r/979A8436335E3744ADCD3A9F2A2B68A52AD136BE@SJEXCHMB10.corp.ad.broadcom.com
Reported-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
All other PCIe capability register fields include "PCI_EXP" + <reg-name> +
<field-name>. This renames PCI_EXP_OBFF_MASK, PCI_EXP_IDO_REQ_EN,
PCI_EXP_LTR_EN, and related fields using the same convention.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com> # for MFD driver
|
|
* acpi-assorted:
ACPI / osl: Kill macro INVALID_TABLE().
earlycpio.c: Fix the confusing comment of find_cpio_data().
ACPI / x86: Print Hot-Pluggable Field in SRAT.
ACPI / thermal: Use THERMAL_TRIPS_NONE macro to replace number
ACPI / thermal: Remove unused macros in the driver/acpi/thermal.c
ACPI / thermal: Remove the unused lock of struct acpi_thermal
ACPI / osl: Fix osi_setup_entries[] __initdata attribute location
ACPI / numa: Fix __init attribute location in slit_valid()
ACPI / dock: Fix __init attribute location in find_dock_and_bay()
ACPI / Sleep: Fix incorrect placement of __initdata
ACPI / processor: Fix incorrect placement of __initdata
ACPI / EC: Fix incorrect placement of __initdata
ACPI / scan: Drop unnecessary label from acpi_create_platform_device()
ACPI: Move acpi_bus_get_device() from bus.c to scan.c
ACPI / scan: Allow platform device creation without any IO resources
ACPI: Cleanup sparse warning on acpi_os_initialize1()
platform / thinkpad: Remove deprecated hotkey_report_mode parameter
ACPI: Remove the old /proc/acpi/event interface
|
|
* acpi-pci-hotplug: (34 commits)
ACPI / PM: Hold acpi_scan_lock over system PM transitions
ACPI / hotplug / PCI: Fix NULL pointer dereference in cleanup_bridge()
PCI / ACPI: Use dev_dbg() instead of dev_info() in acpi_pci_set_power_state()
ACPI / hotplug / PCI: Get rid of check_sub_bridges()
ACPI / hotplug / PCI: Clean up bridge_mutex usage
ACPI / hotplug / PCI: Redefine enable_device() and disable_device()
ACPI / hotplug / PCI: Sanitize acpiphp_get_(latch)|(adapter)_status()
ACPI / hotplug / PCI: Get rid of unused constants in acpiphp.h
ACPI / hotplug / PCI: Check for new devices on enabled slots
ACPI / hotplug / PCI: Allow slots without new devices to be rescanned
ACPI / hotplug / PCI: Do not check SLOT_ENABLED in enable_device()
ACPI / hotplug / PCI: Do not exectute _PS0 and _PS3 directly
ACPI / hotplug / PCI: Do not queue up event handling work items in vain
ACPI / hotplug / PCI: Consolidate slot disabling and ejecting
ACPI / hotplug / PCI: Drop redundant checks from check_hotplug_bridge()
ACPI / hotplug / PCI: Rework namespace scanning and trimming routines
ACPI / hotplug / PCI: Store parent in functions and bus in slots
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_bridge
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_func
ACPI / hotplug / PCI: Embed function struct into struct acpiphp_context
...
|
|
* acpi-cleanup: (21 commits)
ACPI / dock: fix error return code in dock_add()
ACPI / dock: Drop unnecessary local variable from dock_add()
ACPI / dock / PCI: Drop ACPI dock notifier chain
ACPI / dock: Do not check CONFIG_ACPI_DOCK_MODULE
ACPI / dock: Do not leak memory on falilures to add a dock station
ACPI: Drop ACPI bus notifier call chain
ACPI / dock: Rework the handling of notifications
ACPI / dock: Simplify dock_init_hotplug() and dock_release_hotplug()
ACPI / dock: Walk list in reverse order during removal of devices
ACPI / dock: Rework and simplify find_dock_devices()
ACPI / dock: Drop the hp_lock mutex from struct dock_station
ACPI: simplify acpiphp driver with new helper functions
ACPI: simplify dock driver with new helper functions
ACPI: Export acpi_(bay)|(dock)_match() from scan.c
ACPI: introduce two helper functions for _EJ0 and _LCK
ACPI: introduce helper function acpi_execute_simple_method()
ACPI: introduce helper function acpi_has_method()
ACPI / dock: simplify dock_create_acpi_device()
ACPI / dock: mark initialization functions with __init
ACPI / dock: drop redundant spin lock in dock station object
...
|
|
* pci/yijing-mps-v8:
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
PCI: Simplify pcie_bus_configure_settings() interface
PCI: Drop "PCI-E" prefix from Max Payload Size message
|
|
* pci/yinghai-assign-unassigned-v6:
PCI: Assign resources for hot-added host bridge more aggressively
PCI: Move resource reallocation code to non-__init
PCI: Delay enabling bridges until they're needed
PCI: Assign resources on a per-bus basis
PCI: Enable unassigned resource reallocation on per-bus basis
PCI: Turn on reallocation for unassigned resources with host bridge offset
PCI: Look for unassigned resources on per-bus basis
PCI: Drop temporary variable in pci_assign_unassigned_resources()
|
|
If a BIOS configures MPS incorrectly, devices may not work normally.
For example, if a bridge has MPS set larger than an endpoint below it,
the endpoint may discard packets.
To help diagnose this issue, print a warning if we find an endpoint
MPS setting different than that of the upstream bridge.
[bhelgaas: changelog, "bridge" temporary, warning text]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=60799
Reported-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jon Mason <jdmason@kudzu.us>
|
|
Correct minor wording issue in MPS peer-to-peer comment. Noticed by Don
Dutile.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We disable BARs while sizing them so we don't cause conflicts with other
devices (see 253d2e5498 and bbffe43524). But if device decoding is already
disabled before we size the BAR, we don't need to disable it again.
[bhelgaas: changelog, add PCI_COMMAND_DECODING_ENABLE for readability]
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Per f5f2b13129 ("msi: sanely support hardware level msi disabling"), we
want pci_msi_off() to work even if MSI support is not compiled into the
kernel, and there are existing callers that use it when CONFIG_PCI_MSI=n.
This adds a comment to that effect.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Platforms may want to provide architecture-specific functionality when
a PCI device is doing a hibernate transition. Add a weak symbol
pcibios_pm_ops that architectures can override to do so.
[bhelgaas: fold in return value checks from v2 patch]
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When booting with "pci=pcie_bus_safe", we previously limited the
fabric MPS to 128 when we found:
(1) A hotplug-capable Downstream Port ("dev->is_hotplug_bridge &&
pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT"), or
(2) A hotplug-capable Root Port with a slot that was either empty or
contained a multi-function device ("dev->is_hotplug_bridge &&
!list_is_singular(&dev->bus->devices)")
Part (1) is valid, but part (2) is not.
After a hot-add in the slot below a Root Port, we can reconfigure all
MPS values in the fabric below the Root Port because the new device is
the only thing below the Root Port and there are no active drivers.
Therefore, there's no reason to limit the MPS for Root Ports, no
matter what's in the slot.
Test info:
-+-[0000:40]-+-07.0-[0000:46]--+-00.0 Intel 82576 NIC
\-00.1 Intel 82576 NIC
0000:40:07.0 Root Port bridge to [bus 46] (MPS supported=256)
0000:46:00.0 Endpoint (MPS supported=512)
0000:46:00.1 Endpoint (MPS supported=512)
# echo 0 > /sys/bus/pci/slots/7/power
# echo 1 > /sys/bus/pci/slots/7/power
pcieport 0000:40:07.0: PCI-E Max Payload Size set to 256/ 256 (was 256)
pci 0000:46:00.0: PCI-E Max Payload Size set to 256/ 512 (was 128)
pci 0000:46:00.1: PCI-E Max Payload Size set to 256/ 512 (was 128)
Before this change, we set MPS to 128 for the Root Port and both NICs
because the slot contained a multi-function device and
dev->is_hotplug_bridge && !list_is_singular(&dev->bus->devices)
was true. After this change, we set it to 256.
[bhelgaas: changelog, comments, split out upstream bridge check]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jon Mason <jdmason@kudzu.us>
|
|
PCIe hotplug bridges are always either Root Ports or Downstream Ports. No
other device type can have a PCIe link leading downstream to a slot.
Root Ports don't have an upstream bridge, so "dev->is_hotplug_bridge &&
dev->bus->self" is true if and only if "dev" is a Downstream Port. That
means we can simplify this by looking at the type of "dev" itself, without
looking upstream at all.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After 59875ae489 ("PCI/core: Use PCI Express Capability accessors"),
pcie_get_mps() never returns an error, so don't bother to check for it.
No functional change.
[bhelgaas: changelog, fix pcie_get_mps() doc]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Based on a patch by Jon Mason (see URL below).
All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss". The "mpss" argument is redundant since we
can easily look it up internally. In addition, all callers check
"bus->self" for NULL, which we can also do internally.
This patch simplifies the interface and the callers. No functional change.
Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The conventional spelling is "PCIe", but I think even that is superfluous,
so remove the whole thing.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
After commit bbd34fc (ACPI / hotplug / PCI: Register all devices
under the given bridge) register_slot() is called for all PCI
devices under a given bridge that have corresponding objects in
the ACPI namespace, but it calls acpiphp_register_hotplug_slot()
only for devices satisfying specific criteria. Still,
cleanup_bridge() calls acpiphp_unregister_hotplug_slot() for all
objects created by register_slot(), although it should only call it
for the ones that acpiphp_register_hotplug_slot() has been called
for (successfully). This causes a NULL pointer to be dereferenced
by the acpiphp_unregister_hotplug_slot() executed by cleanup_bridge()
if the object it is called for has not been passed to
acpiphp_register_hotplug_slot().
To fix this problem, check if the 'slot' field of the object passed
to acpiphp_unregister_hotplug_slot() in cleanup_bridge() is not NULL,
which only is the case if acpiphp_register_hotplug_slot() has been
executed for that object. In addition to that, make register_slot()
reset the 'slot' field to NULL if acpiphp_register_hotplug_slot() has
failed for the given object to prevent stale pointers from being
used by acpiphp_unregister_hotplug_slot().
Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|