summaryrefslogtreecommitdiff
path: root/include/asm-avr32/arch-at32ap
AgeCommit message (Collapse)Author
2008-01-26[ARM] 4764/1: [AT91] AT91CAP9 core supportAndrew Victor
Add support for Atmel's AT91CAP9 Customizable Microcontroller family. <http://www.atmel.com/products/AT91CAP/Default.asp> Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-25[AVR32] Add support for AT32AP7001 and AT32AP7002Haavard Skinnemoen
These are derivatives of the AT32AP7000 chip, which means that most of the code stays the same. Rename a few files, functions, definitions and config symbols to reflect that they apply to all AP700x chips, and exclude some platform devices from chips where they aren't present. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-23[AVR32] Implement at32_add_device_cf()Haavard Skinnemoen
Implement at32_add_device_cf() which will add a platform_device for the at32_cf driver (not merged yet). Separate out most of the at32_add_device_ide() code and use it to implement at32_add_device_cf() as well. This changes the API in the following ways: * The board code must initialize data->cs to the chipselect ID to use before calling any of these functions. * The board code must use GPIO_PIN_NONE to indicate unused CF pins. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-23[AVR32] Implement more at32_add_device_foo() functionsHaavard Skinnemoen
Implement functions for adding platform devices for TWI, MCI, AC97C and ABDAC. They may need to be modified to cope with platform data, etc. when the corresponding drivers are ready to be merged, but such changes are much less likely to conflict than adding support for a whole new type of device. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-23[AVR32] Platform code for pata_at32Kristoffer Nyborg Gregertsen
This patch adds platform code for PATA devices on the AP7000. [hskinnemoen@atmel.com: board code left out for now since stk1000 doesn't support IDE out of the box] Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11[AVR32] SMC configuration in clock cyclesKristoffer Nyborg Gregertsen
This patch makes the SMC configuration take timings in clock cycles instead of nanoseconds. A function to calculate timings in clock cycles is added. This patch removes the rounding troubles of the previous SMC configuration method. [hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config] Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11[AVR32] Wire up USBA deviceHaavard Skinnemoen
Implement at32_add_device_usba() and use it to wire up the USBA device on ATSTK1000 and ATNGW100. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11[AVR32] add multidrive support for pio driverMatteo Vit
This patch add multidrive support for pio driver Signed-off-by: Matteo Vit - Dave S.r.l. <matteo.vit@dave.eu> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-07-18[AVR32] Add Atmel SSC driver platform device to AT32AP architectureHans-Christian Egtvedt
This patch adds register definitions, clocks and IRQs to the platform devices. Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-07-18[AVR32] Split SM device into PM, RTC, WDT and EICHaavard Skinnemoen
Split the SM platform device into separate platform devices for PM, RTC, WDT and EIC. This is more correct according to the documentation and allows us to simplify the code a little. Also turn the EIC driver into a real platform driver. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
2007-07-16macb: Use generic PHY layerfrederic RODO
Convert the macb driver to use the generic PHY layer in drivers/net/phy. Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-14[AVR32] gpio_*_cansleep() fixDavid Brownell
The AVR32 <asm/gpio.h> was missing the gpio_*_cansleep() calls, breaking compilation for some code using them. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-05-15[AVR32] Implement platform hooks for atmel_lcdfb driverHaavard Skinnemoen
This modifies and extends the existing lcdc platform code to support the new atmel_lcdfb driver. The ATSTK1000 board code is set up to use the on-board Samsung LTV350QV LCD panel. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-05-11[ARM] 4370/3: AT91: Support for Atmel AT91SAM9RL processors.Andrew Victor
Add support for Atmel's new AT91SAM9RL range of processors. Includes similar peripherals as other AT91SAM9 processors, but with a High-speed USB controller and various sizes of internal SRAM. Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-09Use common cpu_is_xxx() macros on AT91 and AVR32Haavard Skinnemoen
Several drivers shared between AT91 and AVR32 chips use cpu_is_xxx() to handle CPU-specific differences. Currently, such code needs to be inside #ifdef CONFIG_ARCH_AT91 because the macros don't exist on AVR32. By defining the same macros on both AT91 and AVR32, these #ifdefs can be eliminated. Since the macros will evaluate to a constant value for CPUs that aren't supported by the current architecture, any code that is only needed on AT91 will be optimized away on AVR32 and vice versa. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Acked-by: Andrew Victor <andrew@sanpeople.com> Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-04-27[AVR32] Make I/O access macros work with external devicesHaavard Skinnemoen
Fix the I/O access macros so that they work with externally connected devices accessed in little-endian mode over any bus width: * Use a set of macros to define I/O port- and memory operations borrowed from MIPS. * Allow subarchitecture to specify address- and data-mangling * Implement at32ap-specific port mangling (with build-time configurable bus width. Only one bus width at a time supported for now.) * Rewrite iowriteN and friends to use write[bwl] and friends (not the __raw counterparts.) This has been tested using pata_pcmcia to access a CompactFlash card connected to the EBI (16-bit bus width.) Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-27[AVR32] Change system timer from count-compare to Timer/Counter 0Hans-Christian Egtvedt
Due to limitation of the count-compare system timer (not able to count when CPU is in sleep), the system timer had to be changed to use a peripheral timer/counter. The old COUNT-COMPARE code is still present in time.c as weak functions. The new timer is added to the architecture directory. This patch sets up TC0 as system timer The new timer has been tested on AT32AP7000/ATSTK1000 at 100 Hz, 250 Hz, 300 Hz and 1000 Hz. For more details about the timer/counter see the datasheet for AT32AP700x available at http://www.atmel.com/dyn/products/product_card.asp?part_id=3903 Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-27[AVR32] Add nwait and tdf parameters to SMC configurationHans-Christian Egtvedt
Complete the SMC configuration code by adding nwait and tdf parameter. After this change, we support the same parameters as the hardware. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-03-17[PATCH] gpio_direction_output() needs an initial valueDavid Brownell
It's been pointed out that output GPIOs should have an initial value, to avoid signal glitching ... among other things, it can be some time before a driver is ready. This patch corrects that oversight, fixing - documentation - platforms supporting the GPIO interface - users of that call (just one for now, others are pending) There's only one user of this call for now since most platforms are still using non-generic GPIO setup code, which in most cases already couples the initial value with its "set output mode" request. Note that most platforms are clear about the hardware letting the output value be set before the pin direction is changed, but the s3c241x docs are vague on that topic ... so those chips might not avoid the glitches. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Andrew Victor <andrew@sanpeople.com> Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-19Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits) [ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports [ARM] 4140/1: AACI stability add ac97 timeout and retries [ARM] 4139/1: AACI record support [ARM] 4138/1: AACI: multiple channel support for IRQ handling [ARM] 4211/1: Provide a defconfig for ns9xxx [ARM] 4210/1: base for new machine type "NetSilicon NS9360" [ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM [ARM] 4221/1: S3C2443: DMA support [ARM] 4220/1: S3C24XX: DMA system initialised from sysdev [ARM] 4219/1: S3C2443: DMA source definitions [ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443 [ARM] 4217/1: S3C24XX: remove the dma channel show at startup [ARM] 4090/2: avoid clash between PXA and SA1111 defines [ARM] 4216/1: add .gitignore entries for ARM specific files [ARM] 4214/2: S3C2410: Add Armzone QT2410 [ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw [ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST [ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos [ARM] 4137/1: Add kexec support [ARM] 4201/1: SMP barriers pair needed for the secondary boot process ... Fix up conflict due to typedef removal in sound/arm/aaci.h
2007-02-16[AVR32] Use per-controller spi_board_info structuresHaavard Skinnemoen
Set up one spi_board_info array per controller and pass this to at32_add_device_spi so that it can set up any GPIO pins for chip selects based on this information. Extracted from a patch by David Brownell and adapted slightly. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-02-09[AVR32] Add PIOE device and reserve SDRAM pinsHaavard Skinnemoen
The PIOE device was left out before because it muxes SDRAM pins (and is therefore a bit dangerous to mess with) and because no existing drivers had any use for it. It is needed for CompactFlash, however, and now that we have a way to protect the SDRAM pins, it can be safely added. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-02-09[AVR32] Introduce at32_reserve_pin()Haavard Skinnemoen
at32_reserve_pin() can be used for reserving portmux pins without altering their configuration. Useful for e.g. SDRAM pins where we really don't want to change the bootloader-provided configuration. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-02-09[AVR32] GPIO API implementationHaavard Skinnemoen
Arch-neutral GPIO calls for AVR32. GPIO IRQ support written by David Brownell. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-02-08[ARM] 4151/1: AT91 / AVR32: Move at91_pdc.h to linux/atmel_pdc.hAndrew Victor
The Atmel AT91 and AVR32 processor architectures share many of the same peripherals. The PDC (Peripheral Data Controller) registers are also implemented within in a number of the on-chip peripherals (eg, USART, MMC, SPI, SSC, etc). In a attempt not to duplicate the register definitions in each peripheral, or in each architecture, the at91_pdc.h header in asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with linux/atmel_pdc.h. The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*, and the drivers updated accordingly. Original patch from Nicolas Ferre. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-02-08[ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directoriesAndrew Victor
Now that Linux includes support for the Atmel AT91SAM9260 and AT91SAM9261 processors in addition to the original Atmel AT91RM9200 (with support for more AT91 processors pending), the "mach-at91rm9200" and "arch-at91rm9200" directories should be renamed to indicate their more generic nature. The following git commands should be run BEFORE applying this patch: git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91 git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91 Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-12-12Merge branch 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32Linus Torvalds
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32: [AVR32] Add missing #include <linux/param.h> to delay.c [AVR32] Pass dev parameter to dma_cache_sync() [AVR32] Implement intc_get_pending() [AVR32] Don't include <asm/delay.h> [AVR32] Put the chip in "stop" mode when halting the system [AVR32] Set flow handler for external interrupts [AVR32] Remove unused file [AVR32] Remove mii_phy_addr and eth_addr from eth_platform_data [AVR32] Move ethernet tag parsing to board-specific code [AVR32] Add macb1 platform_device [AVR32] Portmux API update
2006-12-08[AVR32] Remove mii_phy_addr and eth_addr from eth_platform_dataHaavard Skinnemoen
The macb driver will probe for the PHY chip and read the mac address from the MACB registers, so we don't need them in eth_platform_data anymore. Since u-boot doesn't currently initialize the MACB registers with the mac addresses, the tag parsing code is kept but instead of sticking the information into eth_platform_data, it uses it to initialize the MACB registers (in case the boot loader didn't do it.) This code should be unnecessary at some point in the future. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-12-08[AVR32] Portmux API updateHaavard Skinnemoen
Rename portmux_set_func to at32_select_periph, add at32_select_gpio and add flags parameter to specify the initial state of the pins. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-11-30[ARM] 3954/1: AT91: Update drivers for new headersAndrew Victor
This patch updates the drivers (and other files) which include the hardware headers. This fixes the breakage introduced in patches 3950/1 and 3951/1 (those patches were getting big). The AVR32 architecture uses the same serial driver and had its own copy of at91rm9200_pdc.h. Renamed it to at91_pdc.h Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-04[PATCH] AVR32: Allow renumbering of serial devicesHaavard Skinnemoen
Allow the board to remap actual USART peripheral devices to serial devices by calling at32_map_usart(hw_id, serial_line). This ensures that even though ATSTK1002 uses USART1 as the first serial port, it will still have a ttyS0 device. This also adds a board-specific early setup hook and moves the at32_setup_serial_console() call there from the platform code. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] atmel_serial: Pass fixed register mappings through platform_dataHaavard Skinnemoen
In order to initialize the serial console early, the atmel_serial driver had to do a hack where it compared the physical address of the port with an address known to be permanently mapped, and used it as a virtual address. This got around the limitation that ioremap() isn't always available when the console is being initalized. This patch removes that hack and replaces it with a new "regs" field in struct atmel_uart_data that the board-specific code can initialize to a fixed virtual mapping for platform devices where this is possible. It also initializes the DBGU's regs field with the address the driver used to check against. On AVR32, the "regs" field is initialized from the physical base address when this it can be accessed through a permanently 1:1 mapped segment, i.e. the P4 segment. If regs is NULL, the console initialization is delayed until the "real" driver is up and running and ioremap() can be used. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: Public definitionsHaavard Skinnemoen
Rename the following public definitions: * AT91_NR_UART -> ATMEL_MAX_UART * struct at91_uart_data -> struct atmel_uart_data * at91_default_console_device -> atmel_default_console_device Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: at91rm9200_usart.hHaavard Skinnemoen
Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename it atmel_usart.h. Also delete AVR32's version of this file. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26[PATCH] AVR32 MTD: Static Memory Controller driverHaavard Skinnemoen
This patchset adds the necessary drivers and infrastructure to access the external flash on the ATSTK1000 board through the MTD subsystem. With this stuff in place, it will be possible to use a jffs2 filesystem stored in the external flash as a root filesystem. It might also be possible to update the boot loader if you drop the write protection of partition 0. As suggested by David Woodhouse, I reworked the patches to use the physmap driver instead of introducing a separate mapping driver for the ATSTK1000. I've also cleaned up the hsmc header by removing useless comments and converting spaces to tabs (my headerfile generator needs some work.) Unfortunately, I couldn't unlock the flash in fixup_use_atmel_lock because the erase regions hadn't been set up yet, so I had to do it from cfi_amdstd_setup instead. This patch: This adds a simple API for configuring the static memory controller along with an implementation for the Atmel HSMC. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26[PATCH] avr32 architectureHaavard Skinnemoen
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000 CPU and the AT32STK1000 development board. AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for cost-sensitive embedded applications, with particular emphasis on low power consumption and high code density. The AVR32 architecture is not binary compatible with earlier 8-bit AVR architectures. The AVR32 architecture, including the instruction set, is described by the AVR32 Architecture Manual, available from http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture. It features a 7-stage pipeline, 16KB instruction and data caches and a full Memory Management Unit. It also comes with a large set of integrated peripherals, many of which are shared with the AT91 ARM-based controllers from Atmel. Full data sheet is available from http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf while the CPU core implementation including caches and MMU is documented by the AVR32 AP Technical Reference, available from http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf Information about the AT32STK1000 development board can be found at http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918 including a BSP CD image with an earlier version of this patch, development tools (binaries and source/patches) and a root filesystem image suitable for booting from SD card. Alternatively, there's a preliminary "getting started" guide available at http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links to the sources and patches you will need in order to set up a cross-compiling environment for avr32-linux. This patch, as well as the other patches included with the BSP and the toolchain patches, is actively supported by Atmel Corporation. [dmccr@us.ibm.com: Fix more pxx_page macro locations] [bunk@stusta.de: fix `make defconfig'] Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Dave McCracken <dmccr@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>