| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
net/mac80211/ibss.c
|
|
brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.
This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"
Cc: stable@vger.kernel.org # 3.10
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to be able to (securely) keep connections alive after
the system was suspended for WoWLAN, we need some additional
APIs. We already have API (ieee80211_gtk_rekey_notify) to tell
wpa_supplicant about the new replay counter if GTK rekeying
was done by the device while the host was asleep, but that's
not sufficient.
If GTK rekeying wasn't done, we need to tell the host about
sequence counters for the GTK (and PTK regardless of rekeying)
that was used while asleep, add ieee80211_set_key_rx_seq() for
that.
If GTK rekeying was done, then we need to be able to disable
the old keys (with ieee80211_remove_key()) and allocate the
new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()).
If protocol offload (e.g. ARP) is implemented, then also the
TX sequence counter for the PTK must be updated, using the new
ieee80211_set_key_tx_seq() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/ethernet/broadcom/Kconfig
|
|
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wireshark already defines radiotap channel flags for 5 and 10 MHz, so
just use them in Linux radiotap too. Furthermore, add rx status flags to
allow drivers to report when they received data on 5 or 10 MHz channels.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
Almost everywhere tabs are used to indent continuation
lines, replace the few places that use spaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
Track the AP's beacon rate in the scan BSS data and in the
interface configuration to let the drivers know which rate
the AP is using. This information may be used by drivers,
in our case to let the firmware optimise beacon RX.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Some chips can tell us if received frame was
encoded with STBC or not. To make this information available
in user space we can use updated radiotap specification:
http://www.radiotap.org/defined-fields/MCS
This patch will set number of STBC encoded spatial streams (Nss).
The HAVE_STBC flag should be provided by driver.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make kerneldoc content match header file content, no functional
change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix unit documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Document rx vs tx status concurrency requirements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow rate control modules to pass a rate selection table to mac80211
and the driver. This allows drivers to fetch the most recent rate
selection from the sta pointer for already buffered frames. This allows
rate control to respond faster to sudden link changes and it is also a
step towards adding minstrel_ht support to drivers like iwlwifi.
When a driver sets IEEE80211_HW_SUPPORTS_RC_TABLE, mac80211 will not
fill info->control.rates with rates from the rate table (to preserve
explicit overrides by the rate control module). The driver then
explicitly calls ieee80211_get_tx_rates to merge overrides from
info->control.rates with defaults from the sta rate table.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some driver implementations need to know whether mandatory
admission control is required by the AP for some ACs. Add
a parameter to the TX queue parameters indicating this.
As there's currently no support for admission control in
mac80211's AP implementation, it's only ever set for the
client implementation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The rates[0] CTS and RTS flags are only set after rate control has been
called, so minstrel cannot use them to for setting the number of
retries. This patch adds two new flags to explicitly indicate RTS/CTS use.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the code always copies the configured MCS mask (even if it is
set to default), but only uses it if legacy rates were also masked out.
Fix this by adding a flag that tracks whether the configured MCS mask is
set to default or not.
Optimize the code further by storing a pointer to the configured rate
mask in txrc instead of using memcpy.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The number of VHT spatial streams (NSS) is found in:
- s8 ieee80211_tx_rate.rate.idx[6:4] (tx - filled by rate control)
- u8 ieee80211_rx_status.vht_nss (rx - filled by driver)
Tx discriminates valid rates indexes with the sign bit and encodes NSS
starting from 0 to 7 (note this matches some hw encodings e.g IWLMVM).
Rx does not have the same constraints, and encodes NSS starting from 1
to 8 (note this matches what wireshark expects in the radiotap header).
To handle ieee80211_tx_rate.rate.idx[6:4] ieee80211_rate_set_vht() and
ieee80211_rate_get_vht_nss() assume their nss parameter and return value
respectively runs from 0 to 7.
ATM, there are only 2 users of these: cfg.c:sta_set_rate_info_t() and
iwlwifi/mvm/tx.c:iwl_mvm_hwrate_to_tx_control(), but both assume nss
runs from 1 to 8.
This patch fixes this inconsistency by making ieee80211_rate_set_vht()
and ieee80211_rate_get_vht_nss() handle an nss running from 1 to 8.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers need SSID in AP and IBSS mode. AP SSID is provided
through BSS_CHANGED_SSID notification. There was no easy way to
do the same for IBSS. In IBSS mode SSID is known but was not
stored in BSS configuration. Extend the AP-mode functionality
to also work in IBSS mode.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mac80211 currently sets uAPSD parameters to have VO AC trigger-
and delivery-enabled, with maximum service period length.
Allow drivers to change these default settings since different
uAPSD client implementations may handle errors differently and
be able to recover from some errors.
Note: some APs may not function correctly if one or all ACs are
trigger- and delivery-enabled, see
http://thread.gmane.org/gmane.linux.kernel.wireless.general/93577.
We retested with this AP and later firmware doesn't have this
bug any more.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add P2P NoA settings for STA mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This basically reverts commit b207cdb07f3f01ec1adaac62e9d0cc918c60a81a.
Now is possible to use drv_{add,remove}_interface() and vif->debugfs_dir
to create/remove per interface debugfs files. Remove redundant
callbacks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There is need create driver own per interface debugfs files. This is
currently done by drv_{add,remove}_interface_debugfs() callbacks. But it
is possible that after we remove interface from the driver (i.e.
on suspend) we call drv_remove_interface_debugfs() function. Fixing this
problem will require to add call drv_{add,remove}_interface_debugfs()
anytime we create and remove interface in mac80211. So it's better to
add debugfs dir dentry to vif structure to allow to create/remove
custom debugfs driver files on drv_{add,remove}_interface().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices have multicast filter capability for each individual
virtual interface rather than just a global one. Add an interface
specific driver callback allowing such drivers to configure this.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The irqsafe version ieee80211_sta_eosp_irqsafe() exists, but
drivers must not mix calls to any irqsafe/non-irqsafe function.
Both ath9k and iwlwifi, the likely first users of this interface,
use non-irqsafe RX/TX/TX status so must also use a non-irqsafe
version of this function. Since no driver uses the _irqsafe()
version, remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement restricting peer VHT capabilities to the device's own
capabilities. This is useful when a single driver supports more
than one device and the devices have different capabilities
(often they will differ in the number of spatial streams), but
in particular is also necessary for VHT capability overrides to
work correctly -- otherwise it'd be possible to e.g. advertise,
due to overrides, that TX-STBC is not supported, but then still
use it to TX to the AP because it supports RX-STBC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no driver using this flag, so it seems
that all drivers support HW crypto with WMM or
don't support it at all. Remove the flag and
code setting it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For HT and VHT the current bandwidth can change,
add the function ieee80211_vif_change_bandwidth()
to take care of this. It returns a failure if the
new bandwidth isn't compatible with the existing
channel context, the caller has to handle that.
When it happens, also inform the driver that the
bandwidth changed for this virtual interface (no
drivers would actually care today though.)
Changing to/from HT/VHT isn't allowed though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Handle the operating mode notification action frame.
When the supported streams or the bandwidth change
let the driver and rate control algorithm know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With VHT, a station can change the number of spatial
streams it can receive on the fly, not unlike spatial
multiplexing in HT. Prepare for that by tracking the
maximum number of spatial streams it can receive when
the connection is established.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Scans currently work by stopping the netdev tx queues but leaving the
mac80211 queues active. This stops the flow of incoming packets while
still allowing mac80211 to transmit nullfunc and probe request frames to
facilitate scanning. However, the driver may try to wake the mac80211
queues while in this state, which will also wake the netdev queues.
To prevent this, add a new queue stop reason,
IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx
queues for off-channel operation. This prevents the netdev queues from
waking when a driver wakes the mac80211 queues.
This also stops all frames from being transmitted, even those meant to
be sent off-channel. Add a new tx control flag,
IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted
when the queues are stopped only for the off-channel stop reason. Update
all locations transmitting off-channel frames to use this flag.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The functions were added for some sort of Bluetooth
coexistence, but aren't used, so remove them again.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to be able to predict the next DTIM TBTT
in the driver, add the ability to use timing data
from beacons only with the new hardware flag
IEEE80211_HW_TIMING_BEACON_ONLY and the BSS info
value sync_dtim_count which is only valid if the
timing data came from a beacon. The data can only
come from a beacon, and if no beacon was received
before association it is updated later together
with the DTIM count notification.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add debugfs driver callbacks so drivers can add
debugfs entries for interfaces. Note that they
_must_ remove the entries again as add/remove in
the driver doesn't correspond to add/remove in
debugfs; the former is up/down while the latter
is netdev create/destroy.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
