diff options
| -rw-r--r-- | board/freescale/mx6sxsabresd/mx6sxsabresd.c | 84 | ||||
| -rw-r--r-- | include/configs/mx6sxsabresd.h | 13 |
2 files changed, 97 insertions, 0 deletions
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index ff4c88f..24d6a51 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -14,10 +14,14 @@ #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> #include <asm/io.h> +#include <asm/imx-common/mxc_i2c.h> #include <linux/sizes.h> #include <common.h> #include <fsl_esdhc.h> #include <mmc.h> +#include <i2c.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> DECLARE_GLOBAL_DATA_PTR; @@ -29,6 +33,11 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE) + int dram_init(void) { gd->ram_size = PHYS_SDRAM_SIZE; @@ -56,9 +65,77 @@ static void setup_iomux_uart(void) imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); } +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C1 for PMIC */ +struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC, + .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC, + .gp = IMX_GPIO_NR(1, 0), + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC, + .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC, + .gp = IMX_GPIO_NR(1, 1), + }, +}; + +static int pfuze_init(void) +{ + struct pmic *p; + int ret; + unsigned int reg; + + ret = power_pfuze100_init(I2C_PMIC); + if (ret) + return ret; + + p = pmic_get("PFUZE100_PMIC"); + ret = pmic_probe(p); + if (ret) + return ret; + + pmic_reg_read(p, PFUZE100_DEVICEID, ®); + printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + + /* Set SW1AB standby voltage to 0.975V */ + pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); + reg &= ~0x3f; + reg |= 0x1b; + pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); + + /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PUZE_100_SW1ABCONF, ®); + reg &= ~0xc0; + reg |= 0x40; + pmic_reg_write(p, PUZE_100_SW1ABCONF, reg); + + /* Set SW1C standby voltage to 0.975V */ + pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); + reg &= ~0x3f; + reg |= 0x1b; + pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); + + /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PFUZE100_SW1CCONF, ®); + reg &= ~0xc0; + reg |= 0x40; + pmic_reg_write(p, PFUZE100_SW1CCONF, reg); + + /* Enable power of VGEN5 3V3, needed for SD3 */ + pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); + reg &= ~0x1F; + reg |= 0x1F; + pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); + + return 0; +} + int board_early_init_f(void) { setup_iomux_uart(); + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + return 0; } @@ -87,6 +164,13 @@ int board_init(void) return 0; } +int board_late_init(void) +{ + pfuze_init(); + + return 0; +} + int checkboard(void) { puts("Board: MX6SX SABRE SDB\n"); diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h index 390286b..7967b5d 100644 --- a/include/configs/mx6sxsabresd.h +++ b/include/configs/mx6sxsabresd.h @@ -28,6 +28,7 @@ #define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M) #define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_LATE_INIT #define CONFIG_MXC_GPIO #define CONFIG_MXC_UART @@ -168,6 +169,18 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE100 +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 + /* FLASH and environment organization */ #define CONFIG_SYS_NO_FLASH |