diff options
Diffstat (limited to 'arch/powerpc/cpu/ppc4xx/cpu_init.c')
| -rw-r--r-- | arch/powerpc/cpu/ppc4xx/cpu_init.c | 541 |
1 files changed, 0 insertions, 541 deletions
diff --git a/arch/powerpc/cpu/ppc4xx/cpu_init.c b/arch/powerpc/cpu/ppc4xx/cpu_init.c deleted file mode 100644 index 4013a0c..0000000 --- a/arch/powerpc/cpu/ppc4xx/cpu_init.c +++ /dev/null @@ -1,541 +0,0 @@ -/* - * (C) Copyright 2000-2007 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <watchdog.h> -#include <asm/ppc4xx-emac.h> -#include <asm/processor.h> -#include <asm/ppc4xx-gpio.h> -#include <asm/ppc4xx.h> - -DECLARE_GLOBAL_DATA_PTR; - -#ifndef CONFIG_SYS_PLL_RECONFIG -#define CONFIG_SYS_PLL_RECONFIG 0 -#endif - -#if defined(CONFIG_440EPX) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) -static void reset_with_rli(void) -{ - u32 reg; - - /* - * Set reload inhibit so configuration will persist across - * processor resets - */ - mfcpr(CPR0_ICFG, reg); - reg |= CPR0_ICFG_RLI_MASK; - mtcpr(CPR0_ICFG, reg); - - /* Reset processor if configuration changed */ - __asm__ __volatile__ ("sync; isync"); - mtspr(SPRN_DBCR0, 0x20000000); -} -#endif - -void reconfigure_pll(u32 new_cpu_freq) -{ -#if defined(CONFIG_440EPX) - int reset_needed = 0; - u32 reg, temp; - u32 prbdv0, target_prbdv0, /* CLK_PRIMBD */ - fwdva, target_fwdva, fwdvb, target_fwdvb, /* CLK_PLLD */ - fbdv, target_fbdv, lfbdv, target_lfbdv, - perdv0, target_perdv0, /* CLK_PERD */ - spcid0, target_spcid0; /* CLK_SPCID */ - - /* Reconfigure clocks if necessary. - * See PPC440EPx User's Manual, sections 8.2 and 14 */ - if (new_cpu_freq == 667) { - target_prbdv0 = 2; - target_fwdva = 2; - target_fwdvb = 4; - target_fbdv = 20; - target_lfbdv = 1; - target_perdv0 = 4; - target_spcid0 = 4; - - mfcpr(CPR0_PRIMBD0, reg); - temp = (reg & PRBDV_MASK) >> 24; - prbdv0 = temp ? temp : 8; - if (prbdv0 != target_prbdv0) { - reg &= ~PRBDV_MASK; - reg |= ((target_prbdv0 == 8 ? 0 : target_prbdv0) << 24); - mtcpr(CPR0_PRIMBD0, reg); - reset_needed = 1; - } - - mfcpr(CPR0_PLLD, reg); - - temp = (reg & PLLD_FWDVA_MASK) >> 16; - fwdva = temp ? temp : 16; - - temp = (reg & PLLD_FWDVB_MASK) >> 8; - fwdvb = temp ? temp : 8; - - temp = (reg & PLLD_FBDV_MASK) >> 24; - fbdv = temp ? temp : 32; - - temp = (reg & PLLD_LFBDV_MASK); - lfbdv = temp ? temp : 64; - - if (fwdva != target_fwdva || fbdv != target_fbdv || lfbdv != target_lfbdv) { - reg &= ~(PLLD_FWDVA_MASK | PLLD_FWDVB_MASK | - PLLD_FBDV_MASK | PLLD_LFBDV_MASK); - reg |= ((target_fwdva == 16 ? 0 : target_fwdva) << 16) | - ((target_fwdvb == 8 ? 0 : target_fwdvb) << 8) | - ((target_fbdv == 32 ? 0 : target_fbdv) << 24) | - (target_lfbdv == 64 ? 0 : target_lfbdv); - mtcpr(CPR0_PLLD, reg); - reset_needed = 1; - } - - mfcpr(CPR0_PERD, reg); - perdv0 = (reg & CPR0_PERD_PERDV0_MASK) >> 24; - if (perdv0 != target_perdv0) { - reg &= ~CPR0_PERD_PERDV0_MASK; - reg |= (target_perdv0 << 24); - mtcpr(CPR0_PERD, reg); - reset_needed = 1; - } - - mfcpr(CPR0_SPCID, reg); - temp = (reg & CPR0_SPCID_SPCIDV0_MASK) >> 24; - spcid0 = temp ? temp : 4; - if (spcid0 != target_spcid0) { - reg &= ~CPR0_SPCID_SPCIDV0_MASK; - reg |= ((target_spcid0 == 4 ? 0 : target_spcid0) << 24); - mtcpr(CPR0_SPCID, reg); - reset_needed = 1; - } - } - - /* Get current value of FWDVA.*/ - mfcpr(CPR0_PLLD, reg); - temp = (reg & PLLD_FWDVA_MASK) >> 16; - - /* - * Check to see if FWDVA has been set to value of 1. if it has we must - * modify it. - */ - if (temp == 1) { - /* - * Load register that contains current boot strapping option. - */ - mfcpr(CPR0_ICFG, reg); - /* - * Strapping option bits (ICS) are already in correct position, - * only masking needed. - */ - reg &= CPR0_ICFG_ICS_MASK; - - if ((reg == BOOT_STRAP_OPTION_A) || (reg == BOOT_STRAP_OPTION_B) || - (reg == BOOT_STRAP_OPTION_D) || (reg == BOOT_STRAP_OPTION_E)) { - mfcpr(CPR0_PLLD, reg); - - /* Get current value of fbdv. */ - temp = (reg & PLLD_FBDV_MASK) >> 24; - fbdv = temp ? temp : 32; - - /* Get current value of lfbdv. */ - temp = (reg & PLLD_LFBDV_MASK); - lfbdv = temp ? temp : 64; - - /* - * Get current value of FWDVA. Assign current FWDVA to - * new FWDVB. - */ - mfcpr(CPR0_PLLD, reg); - target_fwdvb = (reg & PLLD_FWDVA_MASK) >> 16; - fwdvb = target_fwdvb ? target_fwdvb : 8; - - /* - * Get current value of FWDVB. Assign current FWDVB to - * new FWDVA. - */ - target_fwdva = (reg & PLLD_FWDVB_MASK) >> 8; - fwdva = target_fwdva ? target_fwdva : 16; - - /* - * Update CPR0_PLLD with switched FWDVA and FWDVB. - */ - reg &= ~(PLLD_FWDVA_MASK | PLLD_FWDVB_MASK | - PLLD_FBDV_MASK | PLLD_LFBDV_MASK); - reg |= ((fwdva == 16 ? 0 : fwdva) << 16) | - ((fwdvb == 8 ? 0 : fwdvb) << 8) | - ((fbdv == 32 ? 0 : fbdv) << 24) | - (lfbdv == 64 ? 0 : lfbdv); - mtcpr(CPR0_PLLD, reg); - - /* Acknowledge that a reset is required. */ - reset_needed = 1; - } - } - - /* Now reset the CPU if needed */ - if (reset_needed) - reset_with_rli(); -#endif - -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) - u32 reg; - - /* - * See "9.2.1.1 Booting with Option E" in the 460EX/GT - * users manual - */ - mfcpr(CPR0_PLLC, reg); - if ((reg & (CPR0_PLLC_RST | CPR0_PLLC_ENG)) == CPR0_PLLC_RST) { - /* - * Set engage bit - */ - reg = (reg & ~CPR0_PLLC_RST) | CPR0_PLLC_ENG; - mtcpr(CPR0_PLLC, reg); - - /* Now reset the CPU */ - reset_with_rli(); - } -#endif -} - -#ifdef CONFIG_SYS_4xx_CHIP_21_ERRATA -void -chip_21_errata(void) -{ - /* - * See rev 1.09 of the 405EX/405EXr errata. CHIP_21 says that - * sometimes reading the PVR and/or SDR0_ECID results in incorrect - * values. Since the rev-D chip uses the SDR0_ECID bits to control - * internal features, that means the second PCIe or ethernet of an EX - * variant could fail to work. Also, security features of both EX and - * EXr might be incorrectly disabled. - * - * The suggested workaround is as follows (covering rev-C and rev-D): - * - * 1.Read the PVR and SDR0_ECID3. - * - * 2.If the PVR matches an expected Revision C PVR value AND if - * SDR0_ECID3[12:15] is different from PVR[28:31], then processor is - * Revision C: continue executing the initialization code (no reset - * required). else go to step 3. - * - * 3.If the PVR matches an expected Revision D PVR value AND if - * SDR0_ECID3[10:11] matches its expected value, then continue - * executing initialization code, no reset required. else write - * DBCR0[RST] = 0b11 to generate a SysReset. - */ - - u32 pvr; - u32 pvr_28_31; - u32 ecid3; - u32 ecid3_10_11; - u32 ecid3_12_15; - - /* Step 1: */ - pvr = get_pvr(); - mfsdr(SDR0_ECID3, ecid3); - - /* Step 2: */ - pvr_28_31 = pvr & 0xf; - ecid3_10_11 = (ecid3 >> 20) & 0x3; - ecid3_12_15 = (ecid3 >> 16) & 0xf; - if ((pvr == CONFIG_405EX_CHIP21_PVR_REV_C) && - (pvr_28_31 != ecid3_12_15)) { - /* No reset required. */ - return; - } - - /* Step 3: */ - if ((pvr == CONFIG_405EX_CHIP21_PVR_REV_D) && - (ecid3_10_11 == CONFIG_405EX_CHIP21_ECID3_REV_D)) { - /* No reset required. */ - return; - } - - /* Reset required. */ - __asm__ __volatile__ ("sync; isync"); - mtspr(SPRN_DBCR0, 0x30000000); -} -#endif - -/* - * Breath some life into the CPU... - * - * Reconfigure PLL if necessary, - * set up the memory map, - * initialize a bunch of registers - */ -void -cpu_init_f (void) -{ -#if defined(CONFIG_WATCHDOG) || defined(CONFIG_440GX) || defined(CONFIG_460EX) - u32 val; -#endif - -#ifdef CONFIG_SYS_4xx_CHIP_21_ERRATA - chip_21_errata(); -#endif - - reconfigure_pll(CONFIG_SYS_PLL_RECONFIG); - -#if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && \ - !defined(CONFIG_SYS_4xx_GPIO_TABLE) - /* - * GPIO0 setup (select GPIO or alternate function) - */ -#if defined(CONFIG_SYS_GPIO0_OR) - out32(GPIO0_OR, CONFIG_SYS_GPIO0_OR); /* set initial state of output pins */ -#endif -#if defined(CONFIG_SYS_GPIO0_ODR) - out32(GPIO0_ODR, CONFIG_SYS_GPIO0_ODR); /* open-drain select */ -#endif - out32(GPIO0_OSRH, CONFIG_SYS_GPIO0_OSRH); /* output select */ - out32(GPIO0_OSRL, CONFIG_SYS_GPIO0_OSRL); - out32(GPIO0_ISR1H, CONFIG_SYS_GPIO0_ISR1H); /* input select */ - out32(GPIO0_ISR1L, CONFIG_SYS_GPIO0_ISR1L); - out32(GPIO0_TSRH, CONFIG_SYS_GPIO0_TSRH); /* three-state select */ - out32(GPIO0_TSRL, CONFIG_SYS_GPIO0_TSRL); -#if defined(CONFIG_SYS_GPIO0_ISR2H) - out32(GPIO0_ISR2H, CONFIG_SYS_GPIO0_ISR2H); - out32(GPIO0_ISR2L, CONFIG_SYS_GPIO0_ISR2L); -#endif -#if defined (CONFIG_SYS_GPIO0_TCR) - out32(GPIO0_TCR, CONFIG_SYS_GPIO0_TCR); /* enable output driver for outputs */ -#endif -#endif /* CONFIG_405EP ... && !CONFIG_SYS_4xx_GPIO_TABLE */ - -#if defined (CONFIG_405EP) - /* - * Set EMAC noise filter bits - */ - mtdcr(CPC0_EPCTL, CPC0_EPCTL_E0NFE | CPC0_EPCTL_E1NFE); -#endif /* CONFIG_405EP */ - -#if defined(CONFIG_SYS_4xx_GPIO_TABLE) - gpio_set_chip_configuration(); -#endif /* CONFIG_SYS_4xx_GPIO_TABLE */ - - /* - * External Bus Controller (EBC) Setup - */ -#if (defined(CONFIG_SYS_EBC_PB0AP) && defined(CONFIG_SYS_EBC_PB0CR)) -#if (defined(CONFIG_405GP) || \ - defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ - defined(CONFIG_405EX) || defined(CONFIG_405)) - /* - * Move the next instructions into icache, since these modify the flash - * we are running from! - */ - asm volatile(" bl 0f" ::: "lr"); - asm volatile("0: mflr 3" ::: "r3"); - asm volatile(" addi 4, 0, 14" ::: "r4"); - asm volatile(" mtctr 4" ::: "ctr"); - asm volatile("1: icbt 0, 3"); - asm volatile(" addi 3, 3, 32" ::: "r3"); - asm volatile(" bdnz 1b" ::: "ctr", "cr0"); - asm volatile(" addis 3, 0, 0x0" ::: "r3"); - asm volatile(" ori 3, 3, 0xA000" ::: "r3"); - asm volatile(" mtctr 3" ::: "ctr"); - asm volatile("2: bdnz 2b" ::: "ctr", "cr0"); -#endif - - mtebc(PB0AP, CONFIG_SYS_EBC_PB0AP); - mtebc(PB0CR, CONFIG_SYS_EBC_PB0CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB1AP) && defined(CONFIG_SYS_EBC_PB1CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 1)) - mtebc(PB1AP, CONFIG_SYS_EBC_PB1AP); - mtebc(PB1CR, CONFIG_SYS_EBC_PB1CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB2AP) && defined(CONFIG_SYS_EBC_PB2CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 2)) - mtebc(PB2AP, CONFIG_SYS_EBC_PB2AP); - mtebc(PB2CR, CONFIG_SYS_EBC_PB2CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB3AP) && defined(CONFIG_SYS_EBC_PB3CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 3)) - mtebc(PB3AP, CONFIG_SYS_EBC_PB3AP); - mtebc(PB3CR, CONFIG_SYS_EBC_PB3CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB4AP) && defined(CONFIG_SYS_EBC_PB4CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 4)) - mtebc(PB4AP, CONFIG_SYS_EBC_PB4AP); - mtebc(PB4CR, CONFIG_SYS_EBC_PB4CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB5AP) && defined(CONFIG_SYS_EBC_PB5CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 5)) - mtebc(PB5AP, CONFIG_SYS_EBC_PB5AP); - mtebc(PB5CR, CONFIG_SYS_EBC_PB5CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB6AP) && defined(CONFIG_SYS_EBC_PB6CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 6)) - mtebc(PB6AP, CONFIG_SYS_EBC_PB6AP); - mtebc(PB6CR, CONFIG_SYS_EBC_PB6CR); -#endif - -#if (defined(CONFIG_SYS_EBC_PB7AP) && defined(CONFIG_SYS_EBC_PB7CR) && !(CONFIG_SYS_INIT_DCACHE_CS == 7)) - mtebc(PB7AP, CONFIG_SYS_EBC_PB7AP); - mtebc(PB7CR, CONFIG_SYS_EBC_PB7CR); -#endif - -#if defined (CONFIG_SYS_EBC_CFG) - mtebc(EBC0_CFG, CONFIG_SYS_EBC_CFG); -#endif - -#if defined(CONFIG_WATCHDOG) - val = mfspr(SPRN_TCR); -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) - val |= 0xb8000000; /* generate system reset after 1.34 seconds */ -#elif defined(CONFIG_440EPX) - val |= 0xb0000000; /* generate system reset after 1.34 seconds */ -#else - val |= 0xf0000000; /* generate system reset after 2.684 seconds */ -#endif -#if defined(CONFIG_SYS_4xx_RESET_TYPE) - val &= ~0x30000000; /* clear WRC bits */ - val |= CONFIG_SYS_4xx_RESET_TYPE << 28; /* set board specific WRC type */ -#endif - mtspr(SPRN_TCR, val); - - val = mfspr(SPRN_TSR); - val |= 0x80000000; /* enable watchdog timer */ - mtspr(SPRN_TSR, val); - - reset_4xx_watchdog(); -#endif /* CONFIG_WATCHDOG */ - -#if defined(CONFIG_440GX) - /* Take the GX out of compatibility mode - * Travis Sawyer, 9 Mar 2004 - * NOTE: 440gx user manual inconsistency here - * Compatibility mode and Ethernet Clock select are not - * correct in the manual - */ - mfsdr(SDR0_MFR, val); - val &= ~0x10000000; - mtsdr(SDR0_MFR,val); -#endif /* CONFIG_440GX */ - -#if defined(CONFIG_460EX) - /* - * Set SDR0_AHB_CFG[A2P_INCR4] (bit 24) and - * clear SDR0_AHB_CFG[A2P_PROT2] (bit 25) for a new 460EX errata - * regarding concurrent use of AHB USB OTG, USB 2.0 host and SATA - */ - mfsdr(SDR0_AHB_CFG, val); - val |= 0x80; - val &= ~0x40; - mtsdr(SDR0_AHB_CFG, val); - mfsdr(SDR0_USB2HOST_CFG, val); - val &= ~0xf00; - val |= 0x400; - mtsdr(SDR0_USB2HOST_CFG, val); -#endif /* CONFIG_460EX */ - -#if defined(CONFIG_405EX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ - defined(CONFIG_460SX) - /* - * Set PLB4 arbiter (Segment 0 and 1) to 4 deep pipeline read - */ - mtdcr(PLB4A0_ACR, (mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_RDP_MASK) | - PLB4Ax_ACR_RDP_4DEEP); - mtdcr(PLB4A1_ACR, (mfdcr(PLB4A1_ACR) & ~PLB4Ax_ACR_RDP_MASK) | - PLB4Ax_ACR_RDP_4DEEP); -#endif /* CONFIG_440SP/SPE || CONFIG_460EX/GT || CONFIG_405EX */ -} - -/* - * initialize higher level parts of CPU like time base and timers - */ -int cpu_init_r (void) -{ -#if defined(CONFIG_405GP) - uint pvr = get_pvr(); - - /* - * Set edge conditioning circuitry on PPC405GPr - * for compatibility to existing PPC405GP designs. - */ - if ((pvr & 0xfffffff0) == (PVR_405GPR_RB & 0xfffffff0)) { - mtdcr(CPC0_ECR, 0x60606000); - } -#endif /* defined(CONFIG_405GP) */ - - return 0; -} - -#if defined(CONFIG_PCI) && \ - (defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ - defined(CONFIG_440GR) || defined(CONFIG_440GRX)) -/* - * 440EP(x)/GR(x) PCI async/sync clocking restriction: - * - * In asynchronous PCI mode, the synchronous PCI clock must meet - * certain requirements. The following equation describes the - * relationship that must be maintained between the asynchronous PCI - * clock and synchronous PCI clock. Select an appropriate PCI:PLB - * ratio to maintain the relationship: - * - * AsyncPCIClk - 1MHz <= SyncPCIclock <= (2 * AsyncPCIClk) - 1MHz - */ -static int ppc4xx_pci_sync_clock_ok(u32 sync, u32 async) -{ - if (((async - 1000000) > sync) || (sync > ((2 * async) - 1000000))) - return 0; - else - return 1; -} - -int ppc4xx_pci_sync_clock_config(u32 async) -{ - sys_info_t sys_info; - u32 sync; - int div; - u32 reg; - u32 spcid_val[] = { - CPR0_SPCID_SPCIDV0_DIV1, CPR0_SPCID_SPCIDV0_DIV2, - CPR0_SPCID_SPCIDV0_DIV3, CPR0_SPCID_SPCIDV0_DIV4 }; - - get_sys_info(&sys_info); - sync = sys_info.freqPCI; - - /* - * First check if the equation above is met - */ - if (!ppc4xx_pci_sync_clock_ok(sync, async)) { - /* - * Reconfigure PCI sync clock to meet the equation. - * Start with highest possible PCI sync frequency - * (divider 1). - */ - for (div = 1; div <= 4; div++) { - sync = sys_info.freqPLB / div; - if (ppc4xx_pci_sync_clock_ok(sync, async)) - break; - } - - if (div <= 4) { - mtcpr(CPR0_SPCID, spcid_val[div]); - - mfcpr(CPR0_ICFG, reg); - reg |= CPR0_ICFG_RLI_MASK; - mtcpr(CPR0_ICFG, reg); - - /* do chip reset */ - mtspr(SPRN_DBCR0, 0x20000000); - } else { - /* Impossible to configure the PCI sync clock */ - return -1; - } - } - - return 0; -} -#endif |