diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/k2hk_evm.h | 212 |
1 files changed, 212 insertions, 0 deletions
diff --git a/include/configs/k2hk_evm.h b/include/configs/k2hk_evm.h new file mode 100644 index 0000000..9d0ba24 --- /dev/null +++ b/include/configs/k2hk_evm.h @@ -0,0 +1,212 @@ +/* + * Configuration header file for TI's k2hk-evm + * + * (C) Copyright 2012-2014 + * Texas Instruments Incorporated, <www.ti.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_K2HK_EVM_H +#define __CONFIG_K2HK_EVM_H + +/* Platform type */ +#define CONFIG_SOC_K2HK +#define CONFIG_K2HK_EVM + +/* U-Boot Build Configuration */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 2nd stage loader */ +#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_SYS_THUMB_BUILD + +/* SoC Configuration */ +#define CONFIG_ARMV7 +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_SYS_ARCH_TIMER +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_TEXT_BASE 0x0c001000 +#define CONFIG_SPL_TARGET "u-boot-spi.gph" +#define CONFIG_SYS_DCACHE_OFF + +/* Memory Configuration */ +#define CONFIG_NR_DRAM_BANKS 2 +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_LPAE_SDRAM_BASE 0x800000000 +#define CONFIG_MAX_RAM_BANK_SIZE (2 << 30) /* 2GB */ +#define CONFIG_STACKSIZE (512 << 10) /* 512 KiB */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4 MiB */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \ + GENERATED_GBL_DATA_SIZE) + +/* SPL SPI Loader Configuration */ +#define CONFIG_SPL_TEXT_BASE 0x0c200000 +#define CONFIG_SPL_PAD_TO 65536 +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_PAD_TO - 8) +#define CONFIG_SPL_BSS_START_ADDR (CONFIG_SPL_TEXT_BASE + \ + CONFIG_SPL_MAX_SIZE) +#define CONFIG_SPL_BSS_MAX_SIZE (32 * 1024) +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE (32 * 1024) +#define CONFIG_SPL_STACK_SIZE (8 * 1024) +#define CONFIG_SPL_STACK (CONFIG_SYS_SPL_MALLOC_START + \ + CONFIG_SYS_SPL_MALLOC_SIZE + \ + CONFIG_SPL_STACK_SIZE - 4) +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_SPL_PAD_TO +#define CONFIG_SPL_FRAMEWORK + +/* UART Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_MEM32 +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM1 K2HK_UART0_BASE +#define CONFIG_SYS_NS16550_CLK clk_get_rate(K2HK_CLK1_6) +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* SPI Configuration */ +#define CONFIG_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE K2HK_SPI_BASE +#define CONFIG_SYS_SPI_CLK clk_get_rate(K2HK_LPSC_EMIF25_SPI) +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED + +/* I2C Configuration */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_DAVINCI +#define CONFIG_SYS_DAVINCI_I2C_SPEED 100000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */ +#define CONFIG_SYS_DAVINCI_I2C_SPEED1 100000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE1 0x10 /* SMBus host address */ +#define CONFIG_SYS_DAVINCI_I2C_SPEED2 100000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE2 0x10 /* SMBus host address */ +#define I2C_BUS_MAX 3 + +/* EEPROM definitions */ +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_ENV_EEPROM_IS_ON_I2C + +/* NAND Configuration */ +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_PAGE_2K + +#define CONFIG_SYS_NAND_LARGEPAGE +#define CONFIG_SYS_NAND_BASE_LIST { 0x30000000, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE +#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x100000 +#define CONFIG_MTD_PARTITIONS +#define CONFIG_MTD_DEVICE +#define CONFIG_RBTREE +#define CONFIG_LZO +#define MTDPARTS_DEFAULT "mtdparts=davinci_nand.0:" \ + "1024k(bootloader)ro,512k(params)ro," \ + "-(ubifs)" +/* U-Boot command configuration */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MTDPARTS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_CMD_SF +#define CONFIG_CMD_EEPROM + +/* U-Boot general configuration */ +#define CONFIG_SYS_PROMPT "K2HK EVM # " +#define CONFIG_SYS_CBSIZE 1024 +#define CONFIG_SYS_PBSIZE 2048 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +#define CONFIG_CMDLINE_EDITING +#define CONFIG_VERSION_VARIABLE +#define CONFIG_TIMESTAMP + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "boot=ramfs\0" \ + "tftp_root=/\0" \ + "nfs_root=/export\0" \ + "mem_lpae=1\0" \ + "mem_reserve=512M\0" \ + "addr_fdt=0x87000000\0" \ + "addr_kern=0x88000000\0" \ + "addr_mon=0x0c5f0000\0" \ + "addr_uboot=0x87000000\0" \ + "addr_fs=0x82000000\0" \ + "addr_ubi=0x82000000\0" \ + "fdt_high=0xffffffff\0" \ + "run_mon=mon_install ${addr_mon}\0" \ + "run_kern=bootm ${addr_kern} - ${addr_fdt}\0" \ + "init_ubi=run args_all args_ubi; " \ + "ubi part ubifs; ubifsmount boot\0" \ + "get_fdt_ubi=ubifsload ${addr_fdt} ${name_fdt}\0" \ + "get_kern_ubi=ubifsload ${addr_kern} ${name_kern}\0" \ + "get_mon_ubi=ubifsload ${addr_mon} ${name_mon}\0" \ + "burn_uboot=sf probe; sf erase 0 0x100000; " \ + "sf write ${addr_uboot} 0 ${filesize}\0" \ + "args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1\0" \ + "args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs " \ + "root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,2048\0" \ + "burn_ubi=nand erase.part ubifs; " \ + "nand write ${addr_ubi} ubifs ${filesize}\0" \ + "init_ramfs=run args_all args_ramfs get_fs_ramfs\0" \ + "args_ramfs=setenv bootargs ${bootargs} earlyprintk " \ + "rdinit=/sbin/init rw root=/dev/ram0 " \ + "initrd=0x802000000,9M\0" \ + "mtdparts=mtdparts=davinci_nand.0:" \ + "1024k(bootloader)ro,512k(params)ro,522752k(ubifs)\0" +#define CONFIG_BOOTCOMMAND \ + "run init_${boot} get_fdt_${boot} get_mon_${boot} " \ + "get_kern_${boot} run_mon run_kern" +#define CONFIG_BOOTARGS \ + +/* Linux interfacing */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_SYS_BARGSIZE 1024 +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x08000000) + +#define CONFIG_SUPPORT_RAW_INITRD + +/* we may include files below only after all above definitions */ +#include <asm/arch/hardware.h> +#include <asm/arch/clock.h> +#define CONFIG_SYS_HZ_CLOCK clk_get_rate(K2HK_CLK1_6) + +#endif /* __CONFIG_K2HK_EVM_H */ |