summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-08-08usb: hub: Change USB hub descriptor to match USB 3.0 hubsBin Meng
USB 3.0 hubs have a slightly different hub descriptor than USB 2.0 hubs, with a fixed (rather than variable length) size. Change the host controller drivers that access those last two fields (DeviceRemovable and PortPowerCtrlMask) to use the union. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-08-08usb: hub: Revise wLength for 'get port status' requestBin Meng
For accuracy, we should use 'sizeof(struct usb_port_status)' as the wLength for 'get port status' request, although it happens to be equal to 'sizeof(struct usb_hub_status)'. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-08-08usb: hub: Send correct wValue to get hub descriptor of a USB 3.0 hubBin Meng
Testing a USB 3.0 hub by connecting it to the xHCI port on Intel MinnowMax, when issuing 'get hub descriptor' to the hub, xHCI reports a transfer event TRB with a completion code 6 which means 'Stall Error'. In fact super speed USB hub descriptor type is 0x2a, not 0x29. Sending correct SETUP packet to the hub makes it not stall anymore. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-08-08usb: hub: Update handling connect status/change in usb_scan_port()Bin Meng
It was observed that on Intel MinnowMax board, when xHCI is enabled in the BayTrail SoC, with a USB 3.0 device connected to the bottom USB 3.0 port (mapped to xHCI root port #7), its PORTSC register is always 0x201203 (CCS = 1, CSC = 0). The root cause of such behavior is unknown yet. Connect status change bit is set on the same port with a USB 2.0 device (mapped to xHCI port #1, which is a different port on the root hub). With current logic in usb_scan_port(), the enumeration process will abort if it does not detect a connect status change on a hub port. However since a device connection status is correctly reported, the enumeration process can still continue. With this change, USB device connected to the bottom blue port on MinnowMax board can be enumerated under either SS or HS mode. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Dinh Nguyen <dinguyen@kernel.org>
2017-08-08usb: xhci: Add input slot context in xhci_set_configuration()Bin Meng
A valid input slot context for a 'configure endpoint' command requires the 'Context Entries' field to be initialized to the index of the last valid endpoint context that is defined by the target configuration. We set up the 'Context Entries' field, but we forget to include the input slot context in the input control context 'Add Context flags' bitmap. So xHC will simply ignore input slot context and continue using its own which contains old information of the device. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-08-08usb: xhci: Initialize scratchpad buffer array and scratchpad buffersBin Meng
The scratchpad buffer array is used to define the locations of statically allocated memory pages that are available for the private use of the xHC. The xHCI spec explicitly mentions that system software shall allocate the scratchpad buffers before placing the xHC in to Run mode (Run/Stop (R/S) = ‘1’), however U-Boot is missing this part. This causes xHC on Intel platform does not respond the very first 'enable slot' command that is given to xHC and the 'enable slot' command completion event TRB is never generated and xHC seems to hang forever. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-08-08usb: xhci: Correct command TRB 4th dword initializationBin Meng
In xhci_queue_command(), when the command is not 'reset endpoint', 'stop endpoint' or 'set TR dequeue pointer', endpoint ID should not be encoded in the TRB. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-08-08usb: xhci: Remove incorrect comments for struct xhci_container_ctxBin Meng
There is no member called 'dma' in struct xhci_container_ctx. Remove the comments that mentions it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2017-07-19configs: remove ls1043ardb_sdcard & ls2088ardb_qspi secure targetsPrabhakar Kushwaha
Build of ls1043ardb_sdcard & ls2088ardb_qspi secure targets showing compilation error so removing them for the time being till propper support has been applied. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2017-07-19drivers:net:fsl-mc: Update MC address calculationPrabhakar Kushwaha
Update MC address caluclation as per MC design requirement of address as least significant 512MB address of MC private allocated memory. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
2017-07-19board:ls2080ardb: Update execution of config_board_muxPrabhakar Kushwaha
config_board_mux() is dependent on 'hwconfig' env read value. For some bootloaders like QSPI, env is ready only after relocation. So delay execution of config_board_mux() to misc_init_r(). Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
2017-07-19 armv8: ls1046ardb: update core frequency to 1800MHZPrabhakar Kushwaha
Update the default core frequency to 1800MHZ for best performance under SD boot and eMMC boot. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
2017-07-19fsl/usb: enable errata-a010151 for ls2088a and ls2081aSantan Kumar
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
2017-07-19board/ls2080ardb: Disable SD-related GPIO programmingPrabhakar Kushwaha
LS2080ARDB/LS2088ARDB updated RevF boards do not have smart voltage translator, so no need to program GPIO for LS2088ARDB boards The GPIO programming is required only for LS2081ARDB. Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2017-07-19arm: ls1021atwr: Add distro secure boot supportPrabhakar Kushwaha
Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment. Disable fall back option to qspi boot in case of secure boot. Also enable "secureboot=y" flag in environment for ARM based platforms instead of bootcmd. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
2017-07-19arm64: ls1046ardb: Add distro boot supportPrabhakar Kushwaha
Tested on ls1046ardb with automatically boot Ubuntu from SD card or USB disk, if it fails to detect external storage disk, fall back to qspi boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
2017-07-19arm: ls1021atwr: Add distro boot supportPrabhakar Kushwaha
Include common config_distro_defaults.h and config_distro_bootcmd.h for u-boot enviroments to support distro boot which automatically scan boot.scr from storage devices(e.g. SD/USB/SATA/SCSI disk) and execute autoboot script. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Alison Wang <alison.wang@nxp.com>
2017-07-19armv8: ls1046a: move CONFIG_CMD_USB to defconfigPrabhakar Kushwaha
Move the macro to defconfig to take effect globally. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
2017-07-19usb: ums: support multiple controllers using controller_indexRajesh Bhagat
Adds a new field in fsg_common namely controller_index to support multiple controllers usb gadget support. Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2017-07-19usb: dwc3: Add helper functions to enable snooping and burst settingsRajat Srivastava
Adds helper functions to enable snooping and outstanding burst beat settings. Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2017-07-19armv7: Add workaround for USB erratum A-009007Suresh Gupta
USB3PHY Observing Intermittent Failure in Rx This patch is adding the erratum for LS1021. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
2017-07-19armv7: Add workaround for USB erratum A-008997Suresh Gupta
USB3 LFPS Peak-Peak Differential Output Voltage Adjustment This patch is adding the erratum for LS1021. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
2017-07-19armv7: Add workaround for USB erratum A-009798Suresh Gupta
USB High Speed Squelch Threshold Adjustment This patch is adding the erratum for LS1021. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
2017-07-19armv7: Add workaround for USB erratum A-009008Suresh Gupta
USB High Speed (HS) EYE Height Adjustment This patch is adding the erratum for LS1021. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
2017-07-18LS2080ARDB: Secure Boot defconfig for QSPI boot.Udit Agarwal
Add the secure boot defconfig for QSPI boot on LS2088ARDB platform. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
2017-07-18spi: fsl_qspi: Add 4bytes address supportSuresh Gupta
The QSPI support the direct 4bytes address command for flash read/write/erase. And the address can cover the whole QSPI memory space. signed-off-by: Yuan Yao <yao.yuan@nxp.com>
2017-07-18sf: add ADDR_4B for 4byte address supportSuresh Gupta
Some new flash don't support bar register but use 4bytes address to support exceed 16MB flash size. So add flash flag: ADDR_4B for some flash which support 4bytes address. Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
2017-07-18sf: Fix s25fs512s erase size and remove SECT_4K flagSuresh Gupta
As per data sheet, S25FS512S support Uniform sector option or erase size of 256 kbytes and Page Programming buffer of 256 or 512 Bytes. So, flag SECT_4K have no significance for this flash. Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
2017-07-10Prepare v2017.07Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-10km/common: remove unused function declarationsHolger Brunck
Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2017-07-10cmd, nand: fix broken output of "nand info"Lothar Waßmann
If the value of either "nand options" or "bbt options" has a zero in the most significant nibble, the '0x' prefix will be isolated from the value like shown below: |Device 0: nand0, sector size 128 KiB | Page size 2048 b | OOB size 64 b | Erase size 131072 b | subpagesize 2048 b | options 0x40000200 | bbt options 0x 60000 Change the format string to produce leading zeroes filling the gap. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
2017-07-10libfdt: Drop -FDT_ERR_TOODEEPSimon Glass
This error code has not been upstreamed and is not really needed since it is unlikely to be triggered. Drop it to maintain compatability with upstream. Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2017-07-10configs: Resync defconfigsTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-09MAINTAINERS: drop bcm283x/rpi maintainershipStephen Warren
It's been a while since I've touched U-Boot on the Raspberry Pi and other things have been taking my time. Drop my maintainership for this port. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2017-07-08powerpc, 8xx: Add support for MCR3000 board from CSSIChristophe Leroy
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000 and CMPC885 which are respectively based on MPC866 and MPC885 processors. This patch adds support for the first board. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08powerpc, 8xx: move Serial driver to drivers/serial/Christophe Leroy
At the same time, move to Kconfig Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08powerpc, 8xx: move SPI driver to drivers/spi/Christophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08powerpc, 8xx: move FEC Ethernet driver in drivers/netChristophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08powerpc, 8xx: Migrate to KconfigChristophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc, 8xx: Properly set CPM frequency in the device treeChristophe Leroy
For processors whose core runs at twice the bus frequency, the fallback frequency calculation in Linux provides a wrong result. Therefore, U-boot needs to pass the correct value. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc, 8xx: Handle checkpatch errors and some of the warnings/checksChristophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc, 8xx: Implement GLL2 ERRATAChristophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Acked-by: Wolfgang Denk <wd@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc, 8xx: Use IO accessors to access IO memoryChristophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc, 8xx: move specific reginfoChristophe Leroy
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc, 8xx: move immap.c in arch/powerpc/cpu/mpc8xx/Christophe Leroy
immap.c used to be common to several CPUs. It is now only linked to the 8xx, so this patch moves it into arch/powerpc/cpu/mpc8xx/ Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08powerpc: Partialy restore core of mpc8xxChristophe Leroy
CS Systemes d'Information (CSSI) manufactures 8xx boards for critical communication systems. Those boards have been running U-Boot since 2010 and will have to be maintained until at least 2027. commit 5b8e76c35ec312a3f73126bd1a2d2c0965b98a9f ("powerpc, 8xx: remove support for 8xx") orphaned those boards by removing support for the mpc8xx CPU. This commit partially restores support for the 8xx, with the following limitations: - Restores support for MPC866 and MPC885 only - Does not restore IDE, PCMCIA, I2C, USB - Does not restore examples - Does not restore POST - Does not restore Ethernet on SCC - Does not restore console on SCC - Does not restore bedbug and kgdb support As the 866 and 885 do not support the following features, they are not restored either: - VIDEO / LCD - RTC clock The CPM uCODE patch is not restored either, because: - 866 and 885 already have support for I2C and SPI relocation without a uCODE patch - relocation of SMC, I2C or SPI is only needed for using SCCs for Ethernet or QMC The dynamic setup/calculation of clocks is removed, we expect the target being use with the clock and PLPRCR register defined in the configuration. All the clock settings for 8xx prior to 866 is removed as well as we now only support 866 and 885. This code is mature and addresses mature boards. Therefore all code enclosed in '#if 0/#endif' and '#if XX_DEBUG/#endif' is unneeded. The following files are not restored by this patch: - arch/powerpc/cpu/mpc8xx/bedbug_860.c - arch/powerpc/cpu/mpc8xx/fec.h - arch/powerpc/cpu/mpc8xx/kgdb.S - arch/powerpc/cpu/mpc8xx/plprcr_write.S - arch/powerpc/cpu/mpc8xx/scc.c - arch/powerpc/cpu/mpc8xx/upatch.c - arch/powerpc/cpu/mpc8xx/video.c - arch/powerpc/include/asm/status_led.h - arch/powerpc/lib/ide.c - arch/powerpc/lib/ide.h - doc/README.MPC866 - drivers/pcmcia/mpc8xx_pcmcia.c - drivers/rtc/mpc8xx.c - drivers/usb/gadget/mpc8xx_udc.c - drivers/video/mpc8xx_lcd.c - examples/standalone/test_burst.c - examples/standalone/test_burst.h - examples/standalone/test_burst_lib.S - examples/standalone/timer.c - include/mpc823_lcd.h - include/usb/mpc8xx_udc.h - post/cpu/mpc8xx/Makefile - post/cpu/mpc8xx/cache.c - post/cpu/mpc8xx/cache_8xx.S - post/cpu/mpc8xx/ether.c - post/cpu/mpc8xx/spr.c - post/cpu/mpc8xx/uart.c - post/cpu/mpc8xx/usb.c - post/cpu/mpc8xx/watchdog.c Some of the restored files are not located in a proper location. In order to keep traceability of the changes, they will be moved to their correct location and moved to Kconfig in a followup patch. This patch also declares CSSI as point of contact for the update of the 8xx platform, as those boards are the only ones still being maintained on the 8xx area. A later patch will add those boards to the tree. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-07am335x: sl50: Enable CONFIG_AUTOBOOT_KEYEDEnric Balletbo i Serra
On startup the SL50 board halt at U-Boot prompt. Use CONFIG_AUTOBOOT_KEYED to enable autoboot for this board and define the <SPACE> key to get the U-Boot prompt. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2017-07-07board/BuR/brppt1: fix MMC bootHannes Schmelzer
since commit 'd5abcf94c7123167725fc22ace342f0d455093c1' - ti: boot: Register the MMC controllers in SPL in the same way as in u-boot MMC boot on brppt1 board is broken, with this commit we make our board working again. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2017-07-07wdt: Unify option of timeout valueAndy Shevchenko
There is no need to duplicate same option with different name. Kill HW_WATCHDOG_TIMEOUT_MS in favor of WATCHDOG_TIMEOUT_MSECS. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-07wdt: Fix spelling Resettting -> ResettingAndy Shevchenko
Fix spelling Resettting -> Resetting. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
generated by cgit v0.10.2 at 2024-11-16 02:58:32 (GMT)