summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-11-15armv7: ls1021atwr: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1046ardb: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1043ardb: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15cmd: mac: Update description of helpPrabhakar Kushwaha
Update help message for "mac" command to reflect correct descriptions and parameters. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15driver: net: fsl-mc: Use base 16 in simple_strtoulPrabhakar Kushwaha
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base in simple_strtoul. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add distro boot supportAshish Kumar
Distro boot support gives flexibility to run distro RFS like Ubuntu being deployed from SD card or SATA drive. If it fails to detect external storage, fall back to qspi/sd boot. Enable this by default in RDB's defconfig by selecting CONFIG_DISTRO_DEFAULTS Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Zhang Ying <zhangying@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088aqds: Add SD boot support for ls1088qdsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add SD boot support for ls1088Ashish Kumar
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088: Enable SATA for ls1088Ashish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14mtd: nand: fsl-ifc: fix support of multiple NAND devicesKurt Kanzenbach
Currently the chipselect used to identify the corresponding NAND chip is stored at the controller and only set during fsl_ifc_chip_init(). This way, only the last NAND chip is working, as the previous value of cs_nand gets overwritten. In order to solve this issue the chipselect is computed on demand by evaluating the bank variable. Thus, the correct chipselect for each NAND chip operation is used. Tested on hardware with two NAND chips connected to the IFC controller. Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Scott Wood <oss@buserror.net> [YS: reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14armv8: ls1088a: Move CONFIG_SPI_FLASH_SPANSION to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14drivers: net: ldpaa_eth: Correct error handler for qbman_swp_acquire()Ashish Kumar
The zero value returned from qbman_swp_acquire() is an error condition meaning no free buffer for allocation. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Kushwaha Prabhakar <prabhakar@freescale.com> [YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14Prepare v2017.11Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-12Revert "console: simplify puts()"Soeren Moch
This reverts commit c61d0009feb966e0e93254a8c435a1889085e6b8. A tbs2910 board user reported a very slow console frambuffer as regression in current u-boot. I could bisect this down to the above mentioned commit. This revert brings back the fast framebuffer console (one cache flush per string in puts(), not after each char). Reported-by: Uwe Scheffler <scheffler.u@web.de> Signed-off-by: Soeren Moch <smoch@web.de> Tested-by: Uwe Scheffler <scheffler.u@web.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-12board: sysam: stmark2: add missing environment locationAngelo Dureghello
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-11-12ARM: rmobile: Fix eMMC signal voltage on Salvator-X/XSMarek Vasut
The eMMC is 1V8 device only and the signaling is always 1V8, fix the DT for Salvator-X/XS to describe the hardware correctly. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-10Merge git://git.denx.de/u-boot-sunxiTom Rini
2017-11-10sunxi: SATA link timeout fixWerner Böllmann
After updating u-boot from v2016.01 to 2017.09, issue with "SATA link 0 timeout." on my Cubietruck board. mdelay milled after moving satapwr code to board. "sunxi: Turn satapwr on from board_init" (sha1: 9fbb0c3aa49f4604b0342cb527a6bd099f92eaeb) After adding the "mdelay(500);" line that was lost in the path the error is gone. Signed-off-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de> [Rebased and updated change and commit message] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-10net: sun8i_emac: Fix build for non-H3/H5 SoCsChen-Yu Tsai
Only the H3/H5 SoCs have an internal PHY and its related clock and reset controls. Use an #ifdef to guard the internal PHY control code block so it can be built for other SoCs, such as the A83T or A64. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-10Merge git://git.denx.de/u-boot-rockchipTom Rini
2017-11-10rockchip: configs: vyasa: Update falcon offsetsJagan Teki
Update the falcon offsets for args to 16MB and kernel to 17MB Since the below commit updated U-Boot proper location along with rockchip boot image offsets "spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip" (sha1: 8f4d62b403db45dfa8b1cadb9da9096c79b7df47) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-10rockchip: doc: Fix U-Boot proper location for falconJagan Teki
This patch fixed U-Boot proper location has been missed to update in bewlo commit "rockchip: doc: update U-Boot location info" (sha1: 73e6dbe855f357a8330cfd53ff3033303611c1ad) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-10rockchip: doc: update U-Boot location infoGoldschmidt Simon
The U-Boot location has been moved to block 16384. This is 8MB, not 4MB. Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-09Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2017-11-09Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2017-11-09imx7: Add include guards for include/asm/arch-mx7/sys_proto.h fileLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx5: Add include guards for include/asm/arch-mx5/sys_proto.h fileLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx6: Add include guards for include/asm/arch-mx6/sys_proto.h fileLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx:display5: Add support for LWN's DISPLAY5 boardLukasz Majewski
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCsLukasz Majewski
This commit provides generic function to set the RGMII/HSIC IO voltage level on iMX6 devices. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09board: imx6: marsboard: Remove doubled #include <asm/arch/sys_proto.h>Lukasz Majewski
The sys_proto.h file has been included earlier in this file. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09sunxi: restore PHYLIB for CONFIG_SUN4I_EMAC usersArtturi Alm
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h, likely missed in: commit 3146f0c017df ("Move PHYLIB to Kconfig") Signed-off-by: Artturi Alm <artturi.alm@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-09sunxi: fix CONFIG_SUNXI_EMAC referencesArtturi Alm
fixes CONFIG_SUNXI_EMAC references from drivers/net/Makefile and include/configs/sunxi-common.h likely forgotten in: commit abc3e4df59f5 ("sunxi: Convert SUNXI_EMAC to Kconfig") Signed-off-by: Artturi Alm <artturi.alm@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-07mmc: fsl_esdhc: Fix PIO timeoutBenoît Thébaudeau
The following error has been observed on i.MX25 with a high-speed SDSC card: Data Write Failed in PIO Mode. It was caused by the timeout set on PRSSTAT.BWEN, which was triggered because this bit takes 15 ms to be set after writing the first block to DATPORT with this card. Without this timeout, all the blocks are properly written. This timeout was implemented by decrementing a variable, so it was depending on the CPU frequency. Fix this issue by setting this timeout to a long enough absolute duration (500 ms). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-07i.MX6: engicam: Fix MAINTAINERS/READMEJagan Teki
- Update newly added include/configs file in MAINTAINERS - Update newly added defconfig file in README Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-07mx51: Select the ESDHC_A001 erratumFabio Estevam
When a high speed card is connected to mx51evk the following error is seen: U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200) CPU: Freescale i.MX51 rev3.0 at 800 MHz Reset cause: POR Board: MX51EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - read failed, using default environment In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0 => saveenv Saving Environment to MMC... Writing to MMC(0)... failed The root cause for the failure is the eSDHC-A001 erratum: "eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 0x4,0x8, and 0xC" that is listed on some PowerArchitecture chips: https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf Even though eSDHC-A001 is not documented on the i.MX51 errata document, I have confirmed with the NXP design team that this erratum does affect i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001 at SoC level. The i.MX51 ts4800 board already selects this option, but it is better to move this selection to the i.MX51 SoC level instead. Successfully tested with a high speed SD card on a mx51evk board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
2017-11-07mx25: Select the ESDHC_A001 erratumFabio Estevam
When a high speed card is connected to mx25 the following error is seen: U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200) CPU: Freescale i.MX25 rev1.2 at 399 MHz Reset cause: POR Board: MX25PDK I2C: ready DRAM: 64 MiB No arch specific invalidate_icache_all available! MMC: FSL_SDHC: 0 *** Warning - read failed, using default environment In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0 => saveenv Saving Environment to MMC... Writing to MMC(0)... failed , which prevents any usage of the SD card. The root cause for the failure is the eSDHC-A001 erratum: "eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 0x4,0x8, and 0xC" that is listed on some PowerArchitecture chips: https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf Even though eSDHC-A001 is not documented on the i.MX25 errata document, I have confirmed with the NXP design team that this erratum does affect i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001 at SoC level. Successfully tested with a high speed SD card on a mx25pdk board. Suggested-by: Benoît Thébaudeau <benoit@wsystem.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br> Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
2017-11-07mx25: Move MX25 selection to KconfigFabio Estevam
The motivation for moving MX25 selection to Kconfig is to be able to better handle MX25 specific errata, so that an errata option can be selected at SoC level instead of board level. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2017-11-07rockchip: remove SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR from defconfigKever Yang
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead of define a new one. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: doc: update U-Boot location infoKever Yang
Update rockchip U-Boot location to 0x4000/16384. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchipKever Yang
Rockchip use a 'loader2' partition for U-Boot, so u-boot.bin or u-boot.itb load by SPL need to locate at0x4000. Detail here: http://opensource.rock-chips.com/wiki_Boot_option Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: board: puma_rk3399: make env location selectable via KconfigKlaus Goger
The environment storage location is selectable via Kconfig. We support eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store the environment in the SPI-NOR additional to the default eMMC location. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399: change sd-card io voltage to 3.0VKlaus Goger
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399 platforms. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: dts: Use defines for pin names in rk3399-puma.dtsi and rk3368-lion.dtsKlaus Goger
pinctrl/rockchip.h provides defines that map pin numbers to pin names. Use them to make the dts more human readable. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399-puma: update USB configurationPhilipp Tomsich
This change updates the USB configuration for the RK3399-Q7 in the DTS: * fixes the OTG board configuration by enabling it ('okay') * improves the speed of 'usb start' by disabling the unused EHCI/OHCI controllers Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399-puma: update usbhub_enable regulatorPhilipp Tomsich
To correctly model the usbhub_enable regulator for U-Boot, we need to change the settings to: * the GPIO polarity is GPIO_ACTIVE_LOW * should be set to inactive (enable-active-low) when boot-on settings are applied * it can be changed at runtime (i.e. remove the always-on) Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399-puma: fix the modelling of BIOS_DISABLEPhilipp Tomsich
The fixed regulator for overriding BIOS_DISABLE had been modelling backwards (i.e. the GPIO polarity and the enable-active-low/high property had both been inverted), causing the 'regulator' command to always print/expect 'disabled'/'enabled' backwards. This fixes the mix-up and models it correctly: * the GPIO is low-active * the regulator should be enabled (enable-active-high) during boot-on initialisation Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07rockchip: config: use common CONFIG_ENV_SIZE for all SoCsKever Yang
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: config: sync the ENV offset from rockchip legacy U-BootKever Yang
Using the ENV offset from rockchip legacy U-Boot for all SoCs, the offset is 4MB-32KB Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: rock: remove CONFIG_ENV_OFFSETKever Yang
We use the same default ENV setting in rockchip_common.h for all SoC. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
generated by cgit v0.10.2 at 2024-09-28 08:06:30 (GMT)