| Age | Commit message (Collapse) | Author |
|---|
|
Switch to using zImage instead of uImage. and while at it, start using
bootz as default. While at it, get rid of BOOTIMAGE define and start
using Linux upstream dtb file names.
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Use the defaults defined in DEFAULT_LINUX_BOOT_ENV
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Try to maintain as much commonality by conditionally including stuff
in armv7_common as necessary and removing the common defines from
keystone2 header.
Note: as part of this change, all keystone2 platforms will now start
using the generic u-boot prompt instead of the custom prompt.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
rename the keystone2 common header into an keystone2 architecture
specific header which can then reuse the common ti_armv7 config headers.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
CONFIG_LINUX_BOOT_PARAM_ADDR is not a valid configuration option. Do
just like what the rest of the world does.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Commit bd2c4522c26d5 ("ti: armv7: enable EXT support in SPL (using
ti_armv7_common.h)") enabled thumb mode only for SPL builds, however,
All TI armv7 platforms do support thumb, and there is no reason why the
space savings cannot be exploited for u-boot as well.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.
Many of the options are architecture specific, however a lot are common
with v7 architecture. So, step 1 will be to move out OMAP specific stuff
from ti_armv7_common into a ti_armv7_omap.h header which is then used
by all the relevant architecture headers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
CONFIG_MUSB_HDC should be CONFIG_MUSB_HCD to have any effect.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
Gumstix is migrating from ext3 to ext4 file system.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
|
|
Mainline Linux kernel commit
338a6aaabc02fa63b70441dd0e1b70aea64673c6 (ARM: dts: Introduce
STM32F429 MCU) in arch/arm/boot/dts/stm32f429.dtsi
requires U-Boot to set system clock to 180 MHz.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
|
|
While most stm32f4 run at 168 MHz, stm32f429 can work till 180 MHz.
Add option to select 180 MHz through macro CONFIG_SYS_CLK_FREQ.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
|
|
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
|
|
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Fix up a few typos in documentation.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
|
|
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The config file for the siemens-am33x-common was using OMAP_I2C_STANDARD, which
is defined in a header that is not included in the config header. In most cases,
it was being included by the code using CONFIG_SYS_OMAP24_I2C_SPEED, but it
might not always be the case.
In particular, when introducing I2C SPL support in omap-common's boot-common.c,
the header is missing and including it breaks other devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
This cleans up the SPL boot devices for omap platforms and introduces support
for missing boot devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The symbolic link to SoC/CPU specific header directory is created
during the build, while it is only necessary for ARM, AVR32, SPARC,
x86, and some CPUs of PowerPC. For the other architectures, it just
results in a broken symbolic link.
Introduce CONFIG_CREATE_ARCH_SYMLINK to not create unneeded symbolic
links.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There are only two SoC-specific headers for this architecture:
- arch/nds32/include/asm/arch-ag101/ag101.h
- arch/nds32/include/asm/arch-ag102/ag102.h
Those two have different file names, so there is no advantage to
include them via symbolic linked directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
property
In case of enable CONFIG_OF_CONTROL and has a "model" property in the root node,
the board special "checkboard" will not be called.
Usually we show some useful version information in the function.
This patch enable call "checkboard" in any case.
It is not conflicting with showing "model" at the same time.
For example on LS2085AQDS:
Showing "model" only:
Model: Freescale Layerscape 2085a QDS Board
Showing "checkboard" only:
Board: LS2085E-QDS, Board Arch: V1, Board version: B, boot from vBank: 4
Showing both:
Model: Freescale Layerscape 2085a QDS Board
Board: LS2085E-QDS, Board Arch: V1, Board version: B, boot from vBank: 4
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The MCAST_TFTP support requires that network drivers has mcast functon
implemented. This commit adds dummy keystone2_eth_bcast_addr() to meet
the requirement. As far as the driver doesn't use ALE and doesn't filter
any incoming packets, the function is empty.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
When core A turning of core B, via tetris DPSC it places the core
B DPSC into transitional state. The core B has to execute wfi instruction
to move its DPSC to the OFF state. This patch add such instruction.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Only 2 frequencies are supported. The current driver implementation does
not always use the 2 last configured blink frequencies. This patch
fixes this problem. So that the last two entered frequencies are
active.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
Mainline kernel will be using this device name as well.
Signed-off-by: Kamil Lulko <rev13@wp.pl>
|
|
Prior to this commit, it was impossible to use relative path to
include Makefiles from the top level Makefile because the option
"--include-dir=$(srctree)" becomes effective when Make enters into
sub Makefiles.
To use relative path in any places, this commit moves the option
above the "sub-make" target.
This was imported from Linux (commit a436bb7b8063) and adjusted for
U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
$(always) is added to targets by scripts/Makefile.build.
Moreover, filechk does not need .*.cmd files.
Adding these two files to targets is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Update some build scripts to match Linux 4.1. Commit-based syncing
was done so as not to break U-Boot specific changes.
The previous big sync was from Linux 3.18-rc1 by commit 176d09827725
(kbuild: sync misc scripts with Linux 3.18-rc1).
The commits imported from Linux (some with adjustments) are:
[1] commit 9fb5e5372208973984a23ee6f5f025c05d364633
Author: Robert Richter <rrichter@cavium.com>
dts, kbuild: Factor out dtbs install rules to Makefile.dtbinst
[2] commit 371fdc77af44f4cb32475fd499e1d912ccc30890
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: collect shorthands into scripts/Kbuild.include
[3] commit a29b82326ed4eb5567b03c85b52c6891578d5a03
Author: Michal Marek <mmarek@suse.cz>
kbuild: Remove duplicate $(cmd) definition in Makefile.clean
[4] commit 1846dfbde3e8a53f3673dcb1c1b79fd9b3f8d40d
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: remove redundant -rR flag of hdr-inst
[5] commit 34948e0bbf98640fc1821751b01d2f0cd17d84d5
Author: Michal Marek <mmarek@suse.cz>
kbuild: Drop support for clean-rule
[6] commit a16c5f99a28c9945165c46da27fff8e6f26f8736
Author: Michal Marek <mmarek@suse.cz>
kbuild: Fix removal of the debian/ directory
[7] commit d0d38cd9e853db11e0242b3df4c9c3c4a663fbb4
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: use mixed-targets when two or more config targets are given
[8] commit dd33c03b18b3f2db791eb6a17c37d2de66e4de18
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: fix cc-ifversion macro
[9] commit 665d92e38f65d70796aad2b8e49e42e80815d4a4
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: do not add $(call ...) to invoke cc-version or cc-fullversion
[10] commit 6dcb4e5edf39e3b65a75ca76f087b2fdbee8a808
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: allow cc-ifversion to have the argument for false condition
[11] commit c0a80c0c27e5e65b180a25e6c4c2f7ef9e386cd3
Author: Heiko Carstens <heiko.carstens@de.ibm.com>
ftrace: allow architectures to specify ftrace compile options
[12] commit 0b24becc810dc3be6e3f94103a866f214c282394
Author: Andrey Ryabinin <a.ryabinin@samsung.com>
kasan: add kernel address sanitizer infrastructure
[13] commit 4218affdf57f938c04e3a916a9685ee27079f377
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
kbuild: remove warning about "make depend"
[14] commit 77479b38e2f58890eb221a0418357502a5b41cd6
Author: Nathan Rossi <nathan.rossi@xilinx.com>
kbuild: Create directory for target DTB
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Update the files under scripts/kconfig/ to match Linux 4.1.
Some Kconfig sources have diverged from those in the kernel,
so commit-base syncing was done not to lose U-Boot specific updates.
The commits cherry-picked from Linux are:
[1] commit be8af2d54a66911693eddc556e4f7a866670082b
Author: Bjørn Forsman <bjorn.forsman@gmail.com>
kconfig/lxdialog: get ncurses CFLAGS with pkg-config
[2] commit 3943f42c11896ce82ad3da132c8a5630313bdd0e
Author: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Replace mentions of "list_struct" to "list_head"
[3] commit e4e458b45c5861808674eebfea94cee2258bb2ea
Author: Arjun Sreedharan <arjun024@gmail.com>
calloc/xcalloc: Fix argument order
[4] commit 09950bc256e3628d275f90e016e6f5a039fbdcab
Author: Olof Johansson <olof@lixom.net>
merge_config.sh: Display usage if given too few arguments
[5] commit b6a2ab2cd4739a9573ed41677e53171987b8da34
Author: Colin Ian King <colin.king@canonical.com>
kconfig: use va_end to match corresponding va_start
[6] commit 70529b1a1784503169416df19ce3d68746401340
Author: Michal Marek <mmarek@suse.cz>
kconfig: Get rid of the P() macro in headers
[7] commit 463157444e377bf9b279101b1f16a94c4648c03a
Author: Michal Marek <mmarek@suse.cz>
kconfig: Remove dead code
[8] commit ad8d40cda3ad22ad9e8863d55a5c88f85c0173f0
Author: Michal Marek <mmarek@suse.cz>
kconfig: Remove unnecessary prototypes from headers
[9] commit de4619937229378e81f95e99c9866acc8e207d34
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
kbuild: mergeconfig: fix "jobserver unavailable" warning
[10] commit b9fe99c5b994c6ddc57780993966b18899526c0b
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
kbuild: mergeconfig: move an error check to merge_config.sh
[11] commit 371cfd4ff0611d8bc5d18bbb9cc6a2bc3d56cd3d
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
kbuild: mergeconfig: remove redundant $(objtree)
[12] commit 3a975b8cfcbe026b535f83bde9a3c009bae214f9
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
merge_config.sh: improve indentation
[13] commit bc8f8f5fc47cd02c2c5f3580dac2fe6695af1edd
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
merge_config.sh: rename MAKE to RUNMAKE
[14] commit 63a91033d52e64a22e571fe84924c0b7f21c280d
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
kbuild: add generic mergeconfig target, %.config
[15] commit 1cba0c305758c3c1786ecaceb03e142c95a4edc9
Author: Michal Marek <mmarek@suse.cz>
kconfig: Simplify Makefile
[16] commit 0a1f00a1c86421cc07cec87011c7cf4df68ee54b
Author: Michal Marek <mmarek@suse.cz>
kconfig: Do not print status messages in make -s mode
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Palmas power support is required for OMAP5 devices such as the OMAP5 uEVM, that
need to e.g. enable MMC power at SPL stage.
This is especially important when booting from a peripheral (such as USB, UART),
where the bootrom will not enable power for the MMC device that will hold the
main U-Boot.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Now that the device-model port of the musb mode makes it possible, enable
both the ehci and otg in host mode on boards where the musb is wired up in
host only mode, either via an usb-a receptacle or via an usb <-> sata
converter.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This allows using devices plugged into both ports of the tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
When we return an error the usb core will print an error-message, so in this
case do not print anything.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
|
|
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This way it can be re-checked on "usb reset".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At one point in time the utoo-p66 dts file in the kernel had a bogus
uart entry, and it seems like we synced with the kernel at just the wrong
moment.
This commit removes the bogus uart entry, which breaks booting the utoo-p66
when DM_SERIAL=y.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
|
