| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This patch moves some 4xx specific prototypes out of include common.h
to a ppc4xx specific header.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.
This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:
csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG
I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Since the current dflush() implementation is know to have some problems
(as seem on lwmon5 ECC init) this patch removes it completely and replaces
it by using clean_dcache_range().
Tested on Katmai with ECC DIMM.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Cleanup: Remove custom flash driver for 8 bit boot-eprom and replace it with
the FLASH_CFI_LEGACY et al. config options.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
- Fix some coding style violations.
- Use in/out_u16/32 where appropriate.
- Use register names from ppc405.h.
- Fix trace useage for Lauterbach.
- Remove obsolete generation HCU2.
- Renamed fixed_hcu4_sdram to init_ppc405_sdram.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
- Moved some common code to netstal/common/nm_bsp.c.
- sdram initialisation goes go netstal/common/fixed_sdram.c.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Added some routines used by all Netstal boards:
- nm_bsp.c: - nm_show_print and
- common_misc_init_r
- set_params_for_sw_install. Very specific code to handle our SW
installation procedure
- fixed_sdram.c: Common routines for HCU4 (and upcoming) MCU25 boards
to handle sdram initialization.
- nm.h: Common header
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
- Moved some common code to nestal/common/nm_bsp.c.
- Added support for the vxWorks EDR.
- Enable trace for Lauterbach, if present.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
platforms wishing to display RAM diagnostics in addition to size,
can do so, on one line, in their own board_add_ram_info()
implementation.
this consequently eliminates CONFIG_ADD_RAM_INFO.
Thanks to Stefan for the hint.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Minor cleanups to confirm to the u-boot coding style.
Some german expressions -> english.
HCU5 enforces a unique IP adress for a given slot in the rack.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Make ecc initialisation robust, as DDR2-ECC errors may be generated
while zeroing the RAM.
Return 16 bytes (a cacheline) less than the available memory, as the
board and/or PPC440EPx might have problems accessing the last bytes.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
