summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2018-02-08ls1088a: Moving CONFIG_FSL_QSPI to defconfigRajat Srivastava
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
2018-02-08EHCI: Fix endian access issue on EHCI intinalizationyinbo.zhu
This issue is exposed after commit 9000eddbase0d ("drivers/usb/ehci: Use platform-specific accessors"), the wrong endian way of EHCI controller programing will cause USB function down. Configs Affected: P2041-40-R2.0, P3041-R2.0, P4080-40-R3.0, P5040-21-R2.1, T1024-R1.0, T1040-42-20-22-R1.1, T2080-R1.1, T4240-4160-R2.0 Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
2018-01-29armv8: ls1088a: Move CONFIG_BOOTARGS and CONFIG_CMD_GREPENV to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
2018-01-29armv8: ls1088: Add qixis offsets for lbmap and rcw_srcAshish Kumar
This patch add value for rcw_src and lbmap if the seconday boot targets are ifc and emmc. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
2018-01-18ls1088a: Add VID support for QDS and RDB platformsRajesh Bhagat
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems. It reads the fusesr register and changes the VDD accordingly by adjusting the voltage via LTC3882 regulator. This patch also takes care of the special case of 0.9V VDD is present in fusesr register. In that case,it also changes the SERDES voltage by disabling the SERDES, changing the SVDD and then re-enabling SERDES. Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18board: common: vid: Add support for LTC3882 voltage regulator chipRajesh Bhagat
Restructures common driver to support LTC3882 voltage regulator chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-17configs: ls1012a: add pfe configuration for LS1012ACalvin Johnson
Add configurations for PFE. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Changes in v2: -Moved SYS_LS_PFE_FW_ADDR from pfe Kconfig to board Kconfigs -Add "pfe stop" to ls1012a rdb, frdm and 2g5rdb config files
2018-01-17board: freescale: ls1012ardb: enable network support on ls1012ardbCalvin Johnson
This patch enables ethernet support for ls1012ardb. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Changes in v2: -split from original patch "board: freescale: ls1012a: enable network support on ls1012a platforms" -fix RGMII TX-delay issue
2018-01-12board: ls1012a: LS1012A-2G5RDB board supportBhaskar Upadhaya
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
2018-01-12env: sf: Add support for env init for QSPI-NORAshish Kumar
ENV variables can now be used before relocation. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
2018-01-12armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088Ashish Kumar
IFC-NOR and QSPI-NOR pins are muxed on SoC,so they cannot be accessed simultaneously, but IFC-NOR can be accessed along with SD-BOOT. ls1088aqds_sdcard_ifc_defconfig: is defconfig for SD as boot source and IFC-NOR to be used as flash, this will be used to write IFC-NOR image on IFC flash. QSPI and DSPI cannot be accessed in this defconfig. IFC-NOR image is generated by ls1088aqds_defconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
2018-01-12LS2088ARDB: Correct NOR fall back option failureVinitha V Pillai
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10ls1088aqds: Enable IFC and QIXIS in SPL imageVinitha Pillai-B57223
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10ls1088ardb: Add SD Secure boot target supportVinitha V Pillai
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10armv8: ls1088a: Compile off DCACHE for SPL size reductionVinitha V Pillai
Enable CONFIG_SYS_DCACHE_OFF in case of SPL build as DCACHE is not being enabled in case of SPL image but was compiled in to add redundant code. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10Powerpc: T208xQDS: Modify the comment of the CONFIG_FSL_PCIE_RESET macroBao Xiaowei
Remove duplicate macro CONFIG_FSL_PCIE_RESET and update its comment. It enables PCIe reset to fix link width 2x - 4x. Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
2018-01-10armv8: ls1088a: SPL size reductionVinitha V Pillai
Using changes in this patch we were able to reduce approx 8k size of u-boot-spl.bin image. Following is breif description of changes to reduce SPL size: 1. Changes in board/freescale/ls1088a/Makefile to remove compilation of eth.c and cpld.c in case of SPL build. 2. Changes in board/freescale/ls1088a/ls1088a.c to keep board_early_init_f funcations in case of SPL build. 3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver specific macros due to which static data was being compiled in case of SPL build. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10arm64: ls1012ardb: Add distro secure boot supportVinitha Pillai-B57223
Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment. Enable fall back option to qspi boot in case of secure boot. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
2018-01-09arm64: layerscape: Move CONFIG_HAS_FSL_DR_USB to KconfigRan Wang
Rename to USB_EHCI_FSL, use Kconfig to select ehci accordingly. Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
2018-01-09Move SYS_DPAA_QBMAN to KconfigAhmed Mansour
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to add device tree fixups that allow deep sleep in Linux. The define was placed in header files included by a number of boards, but was not explicitly documented in any of the Kconfigs. A description was added to the drivers/networking menuconfig and default selection for current SOCs that have this part Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com> Series-version: 5 Series-changes: 4 - Add QBMan support in Kconfig auto select for B4420 and T4160 SOCs Series-changes: 5 - Add net device to T1024QDS_DDR4_defconfig to enable QBMan fixup - Remove QBMan define in kmp204x-common.h and rely on SOC auto select Cover-letter: arm: ppc: Share DPAA1 fixups between ARCHs - Support DPAA1 QBMan device tree fixups in a shared location for both arm and ppc architectures - cleanup a define from header files and add as Kconfig with auto selection based on SOC END Series-to: Joe Hershberger <joe.hershberger@ni.com> Series-to: York Sun <york.sun@nxp.com> Series-to: Roy Pledge <roy.pledge@nxp.com> Series-to: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2018-01-09drivers/misc: Share qbman init between archsAhmed Mansour
This patch adds changes necessary to move functionality present in PowerPC folders with ARM architectures that have DPAA1 QBMan hardware - Create new board/freescale/common/fsl_portals.c to house shared device tree fixups for DPAA1 devices with ARM and PowerPC cores - Add new header file to top includes directory to allow files in both architectures to grab the function prototypes - Port inhibit_portals() from PowerPC to ARM. This function is used in setup to disable interrupts on all QMan and BMan portals. It is needed because the interrupts are enabled by default for all portals including unused/uninitialised portals. When the kernel attempts to go to deep sleep the unused portals prevent it from doing so Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com> Series-changes: 2 - Add get_qman_freq() to replace get_sys_info() for readability - Correct the copyright year in new files - Replace !ARM with PPC to wall off PowerPC SOCs specific qman setup - Rename portals.c -> fsl_portals.c for clarity Series-changes: 3 - Add freescale old copyright in new file since it is a modified copy - Add ifdef QBMAN guard around get_qman_freq() - Return freq_qman instead of freq_systembus. More readable and robust - Add white space before return line in get_qman_freq() Series-changes: 4 - Update function name setup_portals() to setup_qbman_portals() in files that were missed the first time Series-changes: 5 - Include <fsl_qbman.h> to fix missing prototype in p1023rdb.c
2018-01-08arm64: ls1012a: Add sata distro boot supportYuantian Tang
Sata is equipped on ls1012a and can be a boot source. Add sata boot support as a option if available. Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
2018-01-08arm64: ls1046a: Add sata distro boot supportYuantian Tang
Sata is equipped on ls1046a and can be a boot source. Add sata boot support as a option if available. Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
2017-12-26boards: ls1046ardb: disable unavailable "ethernet" node in dtsPrabhakar Kushwaha
Linux device tree contains "ethernet" node for all possible interface supported by SoC i.e. LS1046A. It is not necessary for a SerDes protocol to support all possible interface. So disable unavailable "ethernet" node in device tree. Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address sequentially from environment variables Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1046aqds: Adjust IFC timing for NOR flashYork Sun
Increase setup, assertion and hold time related to chip-select signal. Additional delay is needed for the signal to propogate through FPGA. This adjustment slightly increase the read and write cycle but has no impact on burst read or write. Signed-off-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls2080a: Increase load image len for NAND bootYork Sun
Again the image size increases and the length needs to be adjusted. Signed-off-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1012ardb: add more board version informationYangbo Lu
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and detect it when u-boot starts up. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1012ardb: clean up definitions for I2C IO expandersYangbo Lu
This patch is to clean up definitions for I2C IO expanders. The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2. Fixed it in this patch. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26arm64: ls1012afrdm: Add distro boot supportRajesh Bhagat
Include common config_distro_defaults.h and config_distro_bootcmd.h for u-boot enviroments to support automatical distro boot which scan boot.scr from external storage devices(e.g. SD and USB) and execute autoboot script. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26arm64: ls1012ardb: Add distro boot supportRajesh Bhagat
Include common config_distro_defaults.h and config_distro_bootcmd.h for u-boot enviroments to support automatical distro boot which scan boot.scr from external storage devices(e.g. SD and USB) and execute autoboot script. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1088ardb: support force SDHC mode by hwconfigYangbo Lu
The BRDCFG5[SPISDHC] register field of Qixis device is used to control SPI and SDHC signal routing. 10 = Force SDHC Mode - SPI_CS[0] is routed to CPLD for SDHC_VS use. - SPI_CS[1] is unused. - SPI_CS[2:3] are routed to the TDMRiser slot. 11 = Force eMMC Mode - SPI_CS[0:3] are routed to the eMMC card. 0X = Auto Mode - If SDHC_CS_B=0 (SDHC card installed): Use SDHC mode described above. - Else SDHC_CS_B=1 (no SDHC card installed): Use eMMC mode described above. In default the hardware uses auto mode, but sometimes we need to use force SDHC mode to support SD card hotplug, or SD sleep waking up in kernel. This patch is to support force SDHC mode by hwconfig. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1088a: Add nand support for ls1088ardbAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26SECURE BOOT: Add fall back optionVinitha Pillai-B57223
Add fall back option, to boot from NOR/QSPI/SD for LS1043, LS1046, LS1021 in case of distro boot failure. For LS1046, add kernel validation in case of secure boot in sd_bootcmd and qspi_bootcmd. For LS1043 and LS1021, add kernel validation in case of secure boot in sd_bootcmd, qspi_bootcmdand nor_bootcmd. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: LS1088A_QSPI: SECURE_BOOT: Images validationUdit Agarwal
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC phase using esbc_validate command. Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment Add header address for PPA to be validated during ESBC phase for LS1088A platform based on LAyerscape Chasis 3. Moves sec_init prior to ppa_init as for validation of PPA sec must be initialised before the PPA is initialised. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1012a: Modify Kernel and Environment offsetBhaskar Upadhaya
Kernel is now located at 0x1000000 instead of 0xa00000 and envirorment variables are located at 3MB offset instead of 2MB in Flash. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26powerpc/p1_p2_rdb_pc: Fix endian access issue on EHCI intinalizationRan Wang
This issue is exposed after commit 9000eddbae0d ("drivers/usb/ehci: Use platform-specific accessors"), the wrong endianness of EHCI controller programing will cause USB function down. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26powerpc/T104xRDB: Fix endian access issue on EHCI intinalizationRan Wang
This issue is exposed after commit 9000eddbae0d ("drivers/usb/ehci: Use platform-specific accessors"), the wrong endianness of EHCI controller programing will cause USB function down. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls2080ardb: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv7: ls1021atwr: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1046ardb: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1043ardb: Add sd_bootcmd for distro fallback in case of sdbootShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add distro boot supportAshish Kumar
Distro boot support gives flexibility to run distro RFS like Ubuntu being deployed from SD card or SATA drive. If it fails to detect external storage, fall back to qspi/sd boot. Enable this by default in RDB's defconfig by selecting CONFIG_DISTRO_DEFAULTS Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Zhang Ying <zhangying@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088aqds: Add SD boot support for ls1088qdsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add SD boot support for ls1088Ashish Kumar
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088: Enable SATA for ls1088Ashish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14armv8: ls1088a: Move CONFIG_SPI_FLASH_SPANSION to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-10rockchip: configs: vyasa: Update falcon offsetsJagan Teki
Update the falcon offsets for args to 16MB and kernel to 17MB Since the below commit updated U-Boot proper location along with rockchip boot image offsets "spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip" (sha1: 8f4d62b403db45dfa8b1cadb9da9096c79b7df47) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-09Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2017-11-09Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2017-11-09imx:display5: Add support for LWN's DISPLAY5 boardLukasz Majewski
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
generated by cgit v0.10.2 at 2024-10-01 18:52:00 (GMT)