/* * Copyright 2017 NXP * Copyright 2015 Freescale Semiconductor * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __LS2_RDB_H #define __LS2_RDB_H #include "ls2080a_common.h" #undef CONFIG_CONS_INDEX #define CONFIG_CONS_INDEX 2 #ifdef CONFIG_FSL_QSPI #ifdef CONFIG_TARGET_LS2081ARDB #define CONFIG_QIXIS_I2C_ACCESS #endif #define CONFIG_SYS_I2C_EARLY_INIT #define CONFIG_DISPLAY_BOARDINFO_LATE #endif #define I2C_MUX_CH_VOL_MONITOR 0xa #define I2C_VOL_MONITOR_ADDR 0x38 #define CONFIG_VOL_MONITOR_IR36021_READ #define CONFIG_VOL_MONITOR_IR36021_SET #define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" #ifndef CONFIG_SPL_BUILD #define CONFIG_VID #endif /* step the IR regulator in 5mV increments */ #define IR_VDD_STEP_DOWN 5 #define IR_VDD_STEP_UP 5 /* The lowest and highest voltage allowed for LS2080ARDB */ #define VDD_MV_MIN 819 #define VDD_MV_MAX 1212 #ifndef __ASSEMBLY__ unsigned long get_board_sys_clk(void); #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() #define CONFIG_DDR_CLK_FREQ 133333333 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) #define CONFIG_DDR_SPD #define CONFIG_DDR_ECC #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER #define CONFIG_MEM_INIT_VALUE 0xdeadbeef #define SPD_EEPROM_ADDRESS1 0x51 #define SPD_EEPROM_ADDRESS2 0x52 #define SPD_EEPROM_ADDRESS3 0x53 #define SPD_EEPROM_ADDRESS4 0x54 #define SPD_EEPROM_ADDRESS5 0x55 #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ #define CONFIG_DIMM_SLOTS_PER_CTLR 2 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 #endif #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ /* SATA */ #define CONFIG_LIBATA #define CONFIG_SCSI_AHCI #define CONFIG_SCSI_AHCI_PLAT #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 #define CONFIG_SYS_SCSI_MAX_LUN 1 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ CONFIG_SYS_SCSI_MAX_LUN) #ifndef CONFIG_FSL_QSPI /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */ #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) #define CONFIG_SYS_NOR0_CSPR \ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ CSPR_PORT_SIZE_16 | \ CSPR_MSEL_NOR | \ CSPR_V) #define CONFIG_SYS_NOR0_CSPR_EARLY \ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ CSPR_PORT_SIZE_16 | \ CSPR_MSEL_NOR | \ CSPR_V) #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ FTIM0_NOR_TEADC(0x5) | \ FTIM0_NOR_TEAHC(0x5)) #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ FTIM1_NOR_TRAD_NOR(0x1a) |\ FTIM1_NOR_TSEQRAD_NOR(0x13)) #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ FTIM2_NOR_TCH(0x4) | \ FTIM2_NOR_TWPH(0x0E) | \ FTIM2_NOR_TWP(0x1c)) #define CONFIG_SYS_NOR_FTIM3 0x04000000 #define CONFIG_SYS_IFC_CCR 0x01000000 #ifdef CONFIG_MTD_NOR_FLASH #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ CONFIG_SYS_FLASH_BASE + 0x40000000} #endif #define CONFIG_NAND_FSL_IFC #define CONFIG_SYS_NAND_MAX_ECCPOS 256 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 #define CONFIG_SYS_NAND_CSPR_EXT (0x0) #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ | CSPR_MSEL_NAND /* MSEL = NAND */ \ | CSPR_V) #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ #define CONFIG_SYS_NAND_ONFI_DETECTION /* ONFI NAND Flash mode0 Timing Params */ #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ FTIM0_NAND_TWP(0x30) | \ FTIM0_NAND_TWCHT(0x0e) | \ FTIM0_NAND_TWH(0x14)) #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ FTIM1_NAND_TWBE(0xab) | \ FTIM1_NAND_TRR(0x1c) | \ FTIM1_NAND_TRP(0x30)) #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ FTIM2_NAND_TREH(0x14) | \ FTIM2_NAND_TWHRE(0x3c)) #define CONFIG_SYS_NAND_FTIM3 0x0 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) #define CONFIG_FSL_QIXIS /* use common QIXIS code */ #define QIXIS_LBMAP_SWITCH 0x06 #define QIXIS_LBMAP_MASK 0x0f #define QIXIS_LBMAP_SHIFT 0 #define QIXIS_LBMAP_DFLTBANK 0x00 #define QIXIS_LBMAP_ALTBANK 0x04 #define QIXIS_LBMAP_NAND 0x09 #define QIXIS_RST_CTL_RESET 0x31 #define QIXIS_RST_CTL_RESET_EN 0x30 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 #define QIXIS_RCW_SRC_NAND 0x119 #define QIXIS_RST_FORCE_MEM 0x01 #define CONFIG_SYS_CSPR3_EXT (0x0) #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ | CSPR_V) #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ | CSPR_V) #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) /* QIXIS Timing parameters for IFC CS3 */ #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ FTIM0_GPCM_TEADC(0x0e) | \ FTIM0_GPCM_TEAHC(0x0e)) #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ FTIM1_GPCM_TRAD(0x3f)) #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ FTIM2_GPCM_TCH(0xf) | \ FTIM2_GPCM_TWP(0x3E)) #define CONFIG_SYS_CS3_FTIM3 0x0 #if defined(CONFIG_SPL) && defined(CONFIG_NAND) #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 #define CONFIG_ENV_OFFSET (2048 * 1024) #define CONFIG_ENV_SECT_SIZE 0x20000 #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_SPL_PAD_TO 0x80000 #define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) #else #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) #define CONFIG_ENV_SECT_SIZE 0x20000 #define CONFIG_ENV_SIZE 0x2000 #endif /* Debug Server firmware */ #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL #endif #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 #ifdef CONFIG_TARGET_LS2081ARDB #define CONFIG_FSL_QIXIS /* use common QIXIS code */ #define QIXIS_QMAP_MASK 0x07 #define QIXIS_QMAP_SHIFT 5 #define QIXIS_LBMAP_DFLTBANK 0x00 #define QIXIS_LBMAP_QSPI 0x00 #define QIXIS_RCW_SRC_QSPI 0x62 #define QIXIS_LBMAP_ALTBANK 0x20 #define QIXIS_RST_CTL_RESET 0x31 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 #define QIXIS_LBMAP_MASK 0x0f #define QIXIS_RST_CTL_RESET_EN 0x30 #endif /* * I2C */ #ifdef CONFIG_TARGET_LS2081ARDB #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 #endif #define I2C_MUX_PCA_ADDR 0x75 #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ /* I2C bus multiplexer */ #define I2C_MUX_CH_DEFAULT 0x8 /* SPI */ #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI) #define CONFIG_SPI_FLASH #ifdef CONFIG_FSL_QSPI #define CONFIG_SPI_FLASH_STMICRO #endif #ifdef CONFIG_FSL_QSPI #ifdef CONFIG_TARGET_LS2081ARDB #define CONFIG_SPI_FLASH_STMICRO #else #define CONFIG_SPI_FLASH_SPANSION #endif #define FSL_QSPI_FLASH_SIZE SZ_64M /* 64MB */ #define FSL_QSPI_FLASH_NUM 2 #endif #endif /* * RTC configuration */ #define RTC #ifdef CONFIG_TARGET_LS2081ARDB #define CONFIG_RTC_PCF8563 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 #else #define CONFIG_RTC_DS3231 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 #endif /* EEPROM */ #define CONFIG_ID_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_SYS_EEPROM_BUS_NUM 0 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 #define CONFIG_FSL_MEMAC #ifdef CONFIG_PCI #define CONFIG_PCI_SCAN_SHOW #define CONFIG_CMD_PCI #endif /* MMC */ #ifdef CONFIG_MMC #define CONFIG_FSL_ESDHC #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 #endif #define CONFIG_MISC_INIT_R /* * USB */ #define CONFIG_HAS_FSL_XHCI_USB #define CONFIG_USB_XHCI_FSL #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #undef CONFIG_CMDLINE_EDITING #include #define BOOT_TARGET_DEVICES(func) \ func(USB, usb, 0) \ func(MMC, mmc, 0) \ func(SCSI, scsi, 0) \ func(DHCP, dhcp, na) #include /* Initial environment variables */ #undef CONFIG_EXTRA_ENV_SETTINGS #ifdef CONFIG_SECURE_BOOT #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:bank_intlv=auto\0" \ "scriptaddr=0x80800000\0" \ "kernel_addr_r=0x81000000\0" \ "pxefile_addr_r=0x81000000\0" \ "fdt_addr_r=0x88000000\0" \ "ramdisk_addr_r=0x89000000\0" \ "loadaddr=0x80100000\0" \ "kernel_addr=0x100000\0" \ "ramdisk_addr=0x800000\0" \ "ramdisk_size=0x2000000\0" \ "fdt_high=0xa0000000\0" \ "initrd_high=0xffffffffffffffff\0" \ "kernel_start=0x581000000\0" \ "kernel_load=0xa0000000\0" \ "kernel_size=0x2800000\0" \ "mcmemsize=0x40000000\0" \ "fdtfile=fsl-ls2080a-rdb.dtb\0" \ "mcinitcmd=esbc_validate 0x580700000;" \ "esbc_validate 0x580740000;" \ "fsl_mc start mc 0x580a00000" \ " 0x580e00000 \0" \ BOOTENV #else #ifdef CONFIG_QSPI_BOOT #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:bank_intlv=auto\0" \ "scriptaddr=0x80800000\0" \ "kernel_addr_r=0x81000000\0" \ "pxefile_addr_r=0x81000000\0" \ "fdt_addr_r=0x88000000\0" \ "ramdisk_addr_r=0x89000000\0" \ "loadaddr=0x80100000\0" \ "kernel_addr=0x100000\0" \ "ramdisk_size=0x2000000\0" \ "fdt_high=0xa0000000\0" \ "initrd_high=0xffffffffffffffff\0" \ "kernel_start=0x21000000\0" \ "mcmemsize=0x40000000\0" \ "mcinitcmd=fsl_mc start mc 0x20a00000" \ " 0x20e00000 \0" \ BOOTENV #else #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:bank_intlv=auto\0" \ "scriptaddr=0x80800000\0" \ "kernel_addr_r=0x81000000\0" \ "pxefile_addr_r=0x81000000\0" \ "fdt_addr_r=0x88000000\0" \ "ramdisk_addr_r=0x89000000\0" \ "loadaddr=0x80100000\0" \ "kernel_addr=0x100000\0" \ "ramdisk_addr=0x800000\0" \ "ramdisk_size=0x2000000\0" \ "fdt_high=0xa0000000\0" \ "initrd_high=0xffffffffffffffff\0" \ "kernel_start=0x581000000\0" \ "kernel_load=0xa0000000\0" \ "kernel_size=0x2800000\0" \ "mcmemsize=0x40000000\0" \ "fdtfile=fsl-ls2080a-rdb.dtb\0" \ "mcinitcmd=fsl_mc start mc 0x580a00000" \ " 0x580e00000 \0" \ BOOTENV #endif #endif #undef CONFIG_BOOTARGS #define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \ "earlycon=uart8250,mmio,0x21c0600 " \ "ramdisk_size=0x2000000 default_hugepagesz=2m" \ " hugepagesz=2m hugepages=256" #undef CONFIG_BOOTCOMMAND #ifdef CONFIG_QSPI_BOOT /* Try to boot an on-QSPI kernel first, then do normal distro boot */ #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x20d00000" \ " && bootm $kernel_start" \ " || run distro_bootcmd" #else /* Try to boot an on-NOR kernel first, then do normal distro boot */ #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580d00000" \ " && cp.b $kernel_start $kernel_load $kernel_size" \ " && bootm $kernel_load" \ " || run distro_bootcmd" #endif /* MAC/PHY configuration */ #ifdef CONFIG_FSL_MC_ENET #define CONFIG_PHYLIB_10G #define CONFIG_PHY_AQUANTIA #define CONFIG_PHY_CORTINA #define CONFIG_PHYLIB #define CONFIG_SYS_CORTINA_FW_IN_NOR #ifdef CONFIG_QSPI_BOOT #define CONFIG_CORTINA_FW_ADDR 0x20980000 #else #define CONFIG_CORTINA_FW_ADDR 0x580980000 #endif #define CONFIG_CORTINA_FW_LENGTH 0x40000 #define CORTINA_PHY_ADDR1 0x10 #define CORTINA_PHY_ADDR2 0x11 #define CORTINA_PHY_ADDR3 0x12 #define CORTINA_PHY_ADDR4 0x13 #define AQ_PHY_ADDR1 0x00 #define AQ_PHY_ADDR2 0x01 #define AQ_PHY_ADDR3 0x02 #define AQ_PHY_ADDR4 0x03 #define AQR405_IRQ_MASK 0x36 #define CONFIG_MII #define CONFIG_ETHPRIME "DPMAC1@xgmii" #define CONFIG_PHY_GIGE #define CONFIG_PHY_AQUANTIA #endif #include #endif /* __LS2_RDB_H */