1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
|
/*
* Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
*
* Based on Kirkwood support:
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <common.h>
#include <miiphy.h>
#include <netdev.h>
#include <command.h>
#include <i2c.h>
#include <asm/arch/cpu.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
#include <asm/arch/gpio.h>
#include "net2big_v2.h"
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
/* GPIO configuration */
kw_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
MPP3_SPI_MISO,
MPP6_SYSRST_OUTn,
MPP7_GPO, /* Request power-off */
MPP8_TW_SDA,
MPP9_TW_SCK,
MPP10_UART0_TXD,
MPP11_UART0_RXD,
MPP13_GPIO, /* Rear power switch (on|auto) */
MPP14_GPIO, /* USB fuse alarm */
MPP15_GPIO, /* Rear power switch (auto|off) */
MPP16_GPIO, /* SATA HDD1 power */
MPP17_GPIO, /* SATA HDD2 power */
MPP20_SATA1_ACTn,
MPP21_SATA0_ACTn,
MPP24_GPIO, /* USB mode select */
MPP26_GPIO, /* USB device vbus */
MPP28_GPIO, /* USB enable host vbus */
MPP29_GPIO, /* GPIO extension ALE */
MPP34_GPIO, /* Rear Push button 0=on 1=off */
MPP35_GPIO, /* Inhibit switch power-off */
MPP36_GPIO, /* SATA HDD1 presence */
MPP37_GPIO, /* SATA HDD2 presence */
MPP40_GPIO, /* eSATA presence */
MPP44_GPIO, /* GPIO extension (data 0) */
MPP45_GPIO, /* GPIO extension (data 1) */
MPP46_GPIO, /* GPIO extension (data 2) */
MPP47_GPIO, /* GPIO extension (addr 0) */
MPP48_GPIO, /* GPIO extension (addr 1) */
MPP49_GPIO, /* GPIO extension (addr 2) */
0
};
kirkwood_mpp_conf(kwmpp_config);
return 0;
}
int board_init(void)
{
/* Machine number */
gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
/* Boot parameters address */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
return 0;
}
int misc_init_r(void)
{
#ifdef CONFIG_CMD_I2C
if (!getenv("ethaddr")) {
ushort version;
uchar mac[6];
int ret;
/* I2C-0 for on-board EEPROM */
i2c_set_bus_num(0);
/* Check layout version for EEPROM data */
ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
(uchar *) &version, 2);
if (ret != 0) {
printf("Error: failed to read I2C EEPROM @%02x\n",
CONFIG_SYS_I2C_EEPROM_ADDR);
return ret;
}
version = be16_to_cpu(version);
if (version < 1 || version > 3) {
printf("Error: unknown version %d for EEPROM data\n",
version);
return -1;
}
/* Read Ethernet MAC address from EEPROM */
ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac, 6);
if (ret != 0) {
printf("Error: failed to read I2C EEPROM @%02x\n",
CONFIG_SYS_I2C_EEPROM_ADDR);
return ret;
}
eth_setenv_enetaddr("ethaddr", mac);
}
#endif /* CONFIG_CMD_I2C */
return 0;
}
void mv_phy_88e1116_init(char *name)
{
u16 reg;
u16 devadr;
if (miiphy_set_current_dev(name))
return;
/* command to read PHY dev address */
if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
printf("Err..(%s) could not read PHY dev address\n", __func__);
return;
}
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 4.7.2 of chip datasheet
*/
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
/* reset the phy */
if (miiphy_read(name, devadr, MII_BMCR, ®) != 0) {
printf("Err..(%s) PHY status read failed\n", __func__);
return;
}
if (miiphy_write(name, devadr, MII_BMCR, reg | 0x8000) != 0) {
printf("Err..(%s) PHY reset failed\n", __func__);
return;
}
debug("88E1116 Initialized on %s\n", name);
}
/* Configure and initialize PHY */
void reset_phy(void)
{
mv_phy_88e1116_init("egiga0");
}
/* Return GPIO push button status */
static int
do_read_push_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
}
U_BOOT_CMD(button, 1, 1, do_read_push_button,
"Return GPIO push button status 0=off 1=on", "");
|
