path: root/include/configs/simc-t10xx.h

/*
 * Copyright 2017 Scalys B.V.
 * 
 * SPDX-License-Identifier:     GPL-2.0+
 */

#ifndef __SIMC_T10XX_H
#define __SIMC_T10XX_H

#include "simc-t10x0.h"
#include <generated/autoconf.h>



#define CONFIG_MTD_UBI_WL_THRESHOLD	4096
#define CONFIG_MTD_UBI_BEB_LIMIT	20


#define MPC85XX_GPIO_NR(port, pin)     ((((port)-1)*32)+((pin)&31))

/*
 * SIMC-T10xx board configuration file
 */

#define CONFIG_SYS_NAND_BLOCK_SIZE      (256 * 1024)    /* MT29F8G08ABBCAH4*/

/*
 * System and DDR clock
 */
#define CONFIG_SYS_CLK_FREQ		100000000	/* 100 MHz */
#define CONFIG_DDR_CLK_FREQ		133333333	/* 133.33MHz */

#ifdef CONFIG_RAMBOOT_PBL



/* We have to specify all the PBL and RCW since they are used without being 
 * proccessed by the preprocessor */
#if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_NAND_FLASH_BOOT)
/* Secure boot from NAND flash */
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/scalys/simc-t10xx/simc-t10xx_nand_secure_pbi.cfg
#elif defined(CONFIG_SECURE_BOOT) && defined(CONFIG_NOR_FLASH_BOOT)
/* Secure boot from NOR flash */
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/scalys/simc-t10xx/simc-t10xx_nor_secure_pbi.cfg
#elif defined(CONFIG_NAND_FLASH_BOOT)
/* normal boot from NAND flash */
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/scalys/simc-t10xx/simc-t10xx_nand_pbi.cfg
#elif defined(CONFIG_NOR_FLASH_BOOT)
/* normal boot from NOR flash */
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/scalys/simc-t10xx/simc-t10xx_nor_pbi.cfg
#elif defined(CONFIG_SPI_FLASH_BOOT)
/* normal boot frop SPI flash */
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/scalys/simc-t10xx/simc-t10xx_spi_pbi.cfg
#elif defined(CONFIG_SDHC_FLASH_BOOT)
/* normal boot fro sdhc flash */
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/scalys/simc-t10xx/simc-t10xx_sdhc_pbi.cfg
#else
/* unknown configuration, this should not happen */
#error Invalid Boot configuration
#endif

/* Set the RCW config depending on the CPU type */
#if   ( defined(CONFIG_PPC_T1022) || defined(CONFIG_PPC_T1042)) && \
	defined(CONFIG_SECURE_BOOT) && defined(CONFIG_NAND_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x2_nand_secure_rcw.cfg
#elif ( defined(CONFIG_PPC_T1022) || defined(CONFIG_PPC_T1042)) && \
	defined(CONFIG_SECURE_BOOT) && defined(CONFIG_NOR_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x2_nor_secure_rcw.cfg
#elif ( defined(CONFIG_PPC_T1022) || defined(CONFIG_PPC_T1042)) && \
	defined(CONFIG_NAND_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x2_nand_rcw.cfg
#elif ( defined(CONFIG_PPC_T1022) || defined(CONFIG_PPC_T1042)) && \
	defined(CONFIG_NOR_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x2_nor_rcw.cfg
#elif ( defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1040)) && \
	defined(CONFIG_SECURE_BOOT) && defined(CONFIG_NAND_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x0_nand_secure_rcw.cfg
#elif ( defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1040)) && \
	defined(CONFIG_SECURE_BOOT) && defined(CONFIG_NOR_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x0_nor_secure_rcw.cfg
#elif ( defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1040)) && \
	defined(CONFIG_NAND_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x0_nand_rcw.cfg
#elif ( defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1040)) && \
	defined(CONFIG_NOR_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x0_nor_rcw.cfg
#elif ( defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1040)) && \
	defined(CONFIG_SPI_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x0_spi_rcw.cfg
#elif ( defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1040)) && \
	defined(CONFIG_SDHC_FLASH_BOOT)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t10x0_sdhc_rcw.cfg
#else
/* unknown configuration, this should not happen */
#error Invalid Boot configuration
#endif

#if 0
#if defined(CONFIG_PPC_T1022)
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t1022_rcw.cfg
#elif defined(CONFIG_PPC_T1040)
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t1040_nand_secure_rcw.cfg
#else
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t1040_nor_rcw.cfg
/*#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/scalys/simc-t10xx/simc-t1040_rcw.cfg*/
#endif
#endif
#endif 

#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT

#define CONFIG_SPL_I2C_SUPPORT

#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SYS_TEXT_BASE            0x30001000
#define CONFIG_SPL_TEXT_BASE            0xFFFD8000
#define CONFIG_SPL_PAD_TO               0x40000
#define CONFIG_SPL_MAX_SIZE             0x28000

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_SKIP_RELOCATE
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif /* CONFIG_SPL_BUILD */

#define RESET_VECTOR_OFFSET             0x27FFC
#define BOOT_PAGE_OFFSET                0x27000

#define CONFIG_SYS_MAX_FLASH_BANKS      1

#ifdef CONFIG_NAND_FLASH
#define CONFIG_SPL_NAND_SUPPORT

#define CONFIG_SYS_NAND_U_BOOT_SIZE	( (2048-256) *1024)
#define CONFIG_U_BOOT_HDR_SIZE		(16 << 10)


#define CONFIG_SYS_NAND_U_BOOT_DST      0x30000000
#define CONFIG_SYS_NAND_U_BOOT_START    0x30000000
#define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
#ifndef CONFIG_SDHC_FLASH_BOOT 
#define CONFIG_SYS_LDSCRIPT		"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#define CONFIG_SPL_NAND_BOOT
#endif
#endif /* CONFIG_NAND */

#ifdef CONFIG_SDHC_FLASH_BOOT
#define CONFIG_SDCARD
#endif

#ifdef CONFIG_SDCARD
#define	CONFIG_RESET_VECTOR_ADDRESS	0x30000FFC
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_MMC_MINIMAL
#define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST	(0x30000000)
#define CONFIG_SYS_MMC_U_BOOT_START	(0x30000000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
#define CONFIG_SYS_LDSCRIPT		"arch/powerpc/cpu/mpc85xx/u-boot.lds"
#ifndef CONFIG_SPL_BUILD
#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#define CONFIG_SPL_MMC_BOOT
#endif

#endif /* CONFIG_RAMBOOT_PBL */

/* High Level Configuration Options */
#include <asm/config_mpc85xx.h>
#define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
#define CONFIG_MP                       /* support multiple processors */


/* #define CONFIG_DEEP_SLEEP */ /* support deep sleep */
#define CONFIG_SILENT_CONSOLE

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
#endif /* CONFIG_RESET_VECTOR_ADDRESS */

#define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC              CONFIG_SYS_NUM_DDR_CTLRS
#define CONFIG_FSL_CAAM			/* Enable SEC/CAAM */

#define CONFIG_PCI_INDIRECT_BRIDGE

/* The number of available PCI controllers depends on the RCW */
#define CONFIG_PCIE1                    /* PCIE controler 1 */
#define CONFIG_PCIE2                    /* PCIE controler 2 */
#define CONFIG_PCIE3                    /* PCIE controler 3 */
#define CONFIG_PCIE4                    /* PCIE controler 4 */

#define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */

#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET               0x200000 /* Refer to mtdparts */
/* 
 *  CONFIG_ENV_IS_IN_{EEPROM|FLASH|DATAFLASH|ONENAND|SATA|SPI_FLASH|NVRAM|MMC|FAT|EXT4|REMOTE|UBI} or CONFIG_ENV_IS_NOWHERE
 */

#if 0
/* TODO: move env to boot source */
#if defined(CONFIG_SDCARD)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV          0
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_OFFSET               (512 * 0x800)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_OFFSET               0x200000 /* Refer to mtdparts */
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR                 (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_SECT_SIZE            0x20000 /* 128K (one sector) */
#endif /* CONFIG_SPIFLASH */
#endif 

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
#define CONFIG_BTB                      /* toggle branch predition */
#define CONFIG_DDR_ECC

#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE           0x0BADC0DE
#endif /* CONFIG_DDR_ECC */

#define CONFIG_ENABLE_36BIT_PHYS

#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP         64  /* number of TLB1 entries */

/* #define CONFIG_SYS_DRAM_TEST         Executes a memoty test at U-Boot start */
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START        0x00200000
#define CONFIG_SYS_MEMTEST_END          0x00400000
#define CONFIG_SYS_ALT_MEMTEST

#define CONFIG_PANIC_HANG               /* do not reset board on panic */

/*
 *  Config the L3 Cache as L3 SRAM
 */
#define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
#define CONFIG_SYS_L3_SIZE              256 << 10
/* TODO CLEANUP #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) */
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)


/*
 * For Secure Boot CONFIG_SYS_INIT_L3_ADDR will be redefined and hence
 * Physical address (CONFIG_SYS_INIT_L3_ADDR) and virtual address
 * (CONFIG_SYS_INIT_L3_VADDR) will be different.
 */
#define CONFIG_SYS_INIT_L3_VADDR	0xFFFC0000
#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_VADDR + 32 * 1024)


#endif /* CONFIG_RAMBOOT_PBL */
#define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE    (30 << 10)
#define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
#define CONFIG_SPL_RELOC_STACK_SIZE     (22 << 10)

#define CONFIG_SYS_DCSRBAR              0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull

/*
 * DDR Setup
 */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE

/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
#define CONFIG_DIMM_SLOTS_PER_CTLR      (2)
#define CONFIG_CHIP_SELECTS_PER_CTRL    (4)

#define CONFIG_SYS_DDR_RAW_TIMING

#define CONFIG_SYS_SDRAM_SIZE           8192    /* In MByte, for fixed parameter use */

/*
 * IFC Definitions
 */
#ifdef CONFIG_NOR_FLASH
#define CONFIG_SYS_FLASH_BASE           0xe8000000
#define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#endif

/* NAND Flash on IFC */
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE            0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)

#define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
#define CONFIG_SYS_NAND_CSPR            (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                                        | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
                                        | CSPR_MSEL_NAND    /* MSEL = NAND */ \
                                        | CSPR_V)

#define CONFIG_SYS_NAND_AMASK           IFC_AMASK(64*1024)

#define CONFIG_SYS_NAND_CSOR		(CSOR_NAND_ECC_ENC_EN |	/* ECC on encode */ \
					 CSOR_NAND_ECC_DEC_EN |	/* ECC on decode */ \
					 CSOR_NAND_ECC_MODE_4 |	/* 4-bit ECC */ \
					 CSOR_NAND_RAL_3 |	/* RAL = 3Byes */ \
					 CSOR_NAND_PGS_2K |	/* Page Size = 2K */ \
					 CSOR_NAND_SPRZ_128 |	/* Spare size = 128 */ \
					 CSOR_NAND_PB(64) |	/* Pages Per Block = 64 */ \
					 CSOR_NAND_BCTLD)	/* Buffer control disable */

#define CONFIG_SYS_NAND_ONFI_DETECTION

#define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
                                        FTIM0_NAND_TWP(0x18)   | \
                                        FTIM0_NAND_TWCHT(0x07) | \
                                        FTIM0_NAND_TWH(0x0a))
                                        
#define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
                                        FTIM1_NAND_TWBE(0x39)  | \
                                        FTIM1_NAND_TRR(0x0e)   | \
                                        FTIM1_NAND_TRP(0x18))
                                        
#define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
                                        FTIM2_NAND_TREH(0x0a) | \
                                        FTIM2_NAND_TWHRE(0x1e))
                                        
#define CONFIG_SYS_NAND_FTIM3           FTIM3_NAND_TWW(0xa)

#define CONFIG_SYS_NAND_DDR_LAW         11
#define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE      1
/*#define CONFIG_CMD_NAND*/


/* NOR configuation */
/*#define CONFIG_SYS_NO_FLASH*/
#define CONFIG_MTD
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_FLASH_CFI_MTD
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_CFI_WIDTH    FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_PROTECTION
/*#define CONFIG_SYS_NOR_BASE		(0xe8000000)
#define CONFIG_SYS_NOR_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NOR_BASE)
*/
#define CONFIG_SYS_FLASH_BASE           0xe8000000
#define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)


#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}


#define CONFIG_SYS_NOR_CSPR_EXT        (0xf)
#define CONFIG_SYS_NOR_CSPR            (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
					CSPR_PORT_SIZE_16 | \
					CSPR_MSEL_NOR | \
					CSPR_V)

#define CONFIG_SYS_NOR_AMASK           IFC_AMASK(32*1024*1024)

#define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_AVD_TGL_PGM_EN |	/* AVD Toggle Enable during Burst Program */ \
					 CSOR_NOR_ADM_SHIFT(7) |	/* Address Data Multiplexing Shift */ \
					 CSOR_NOR_TRHZ_80) |		/* Time for Read Enable High to Output High Impedance */ \
					 CSOR_NAND_BCTLD		/* Buffer control disable */


/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
				FTIM0_NOR_TEADC(0x5) | \
				FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
				FTIM1_NOR_TRAD_NOR(0x1A) |\
				FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
				FTIM2_NOR_TCH(0x4) | \
				FTIM2_NOR_TWPH(0x0E) | \
				FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3	0x0

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE         CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* start of monitor */
#endif

#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif

/*#define CONFIG_BOARD_EARLY_INIT_R*/
#define CONFIG_MISC_INIT_R

#define CONFIG_HWCONFIG

#define CONFIG_SPL_GPIO_SUPPORT

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR            0xfdd00000  /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH  0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW   0xfe0ec000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS       ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
                                            CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
                                            
#define CONFIG_SYS_INIT_RAM_SIZE            0x00004000

#define CONFIG_SYS_GBL_DATA_OFFSET          (CONFIG_SYS_INIT_RAM_SIZE - \
                                            GENERATED_GBL_DATA_SIZE)
                                            
#define CONFIG_SYS_INIT_SP_OFFSET           CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN              (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN               (32 * 1024 * 1024)

/* Serial Port */
#define CONFIG_CONS_INDEX                   1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE         1
#define CONFIG_SYS_NS16550_CLK              (get_bus_freq(0)/2)

#define CONFIG_SYS_BAUDRATE_TABLE           {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1             (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2             (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3             (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4             (CONFIG_SYS_CCSRBAR+0x11D600)
#define CONFIG_SERIAL_MULTI                 /* Enable both serial ports */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_CONSOLE_IS_IN_ENV        /* determine from environment */
#endif

/* Use the HUSH parser */
/*#define CONFIG_SYS_HUSH_PARSER*/
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "

/* pass open firmware flat tree */


/* new uImage format support */
#if 0
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE  /* enable fit_format_{error,warning}() */
#endif


/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL      /* Use FSL common I2C driver */
#define CONFIG_SYS_FSL_I2C_SPEED    400000  /* I2C speed in Hz */
#define CONFIG_SYS_FSL_I2C2_SPEED   400000
#define CONFIG_SYS_FSL_I2C3_SPEED   400000
#define CONFIG_SYS_FSL_I2C4_SPEED   400000
#define CONFIG_SYS_FSL_I2C_SLAVE    0x7F
#define CONFIG_SYS_FSL_I2C2_SLAVE   0x7F
#define CONFIG_SYS_FSL_I2C3_SLAVE   0x7F
#define CONFIG_SYS_FSL_I2C4_SLAVE   0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET   0x118000
#define CONFIG_SYS_FSL_I2C2_OFFSET  0x118100
#define CONFIG_SYS_FSL_I2C3_OFFSET  0x119000
#define CONFIG_SYS_FSL_I2C4_OFFSET  0x119100

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

#ifdef CONFIG_PCI
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#ifdef CONFIG_PCIE1
#define CONFIG_SYS_PCIE1_MEM_VIRT   0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS    0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS   0xc00000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE   0x10000000  /* 256M */
#define CONFIG_SYS_PCIE1_IO_VIRT    0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS     0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS    0xff8000000ull
#define CONFIG_SYS_PCIE1_IO_SIZE    0x00010000  /* 64k */
#endif

/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#ifdef CONFIG_PCIE2
#define CONFIG_SYS_PCIE2_MEM_VIRT   0x90000000
#define CONFIG_SYS_PCIE2_MEM_BUS    0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS   0xc10000000ull
#define CONFIG_SYS_PCIE2_MEM_SIZE   0x10000000  /* 256M */
#define CONFIG_SYS_PCIE2_IO_VIRT    0xf8010000
#define CONFIG_SYS_PCIE2_IO_BUS     0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS    0xff8010000ull
#define CONFIG_SYS_PCIE2_IO_SIZE    0x00010000  /* 64k */
#endif

/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#ifdef CONFIG_PCIE3
#define CONFIG_SYS_PCIE3_MEM_VIRT   0xa0000000
#define CONFIG_SYS_PCIE3_MEM_BUS    0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS   0xc20000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE   0x10000000  /* 256M */
#define CONFIG_SYS_PCIE3_IO_VIRT    0xf8020000
#define CONFIG_SYS_PCIE3_IO_BUS     0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS    0xff8020000ull
#define CONFIG_SYS_PCIE3_IO_SIZE    0x00010000  /* 64k */
#endif

/* controller 4, Base address 203000 */
#ifdef CONFIG_PCIE4
#define CONFIG_SYS_PCIE4_MEM_VIRT   0xb0000000
#define CONFIG_SYS_PCIE4_MEM_BUS    0xe0000000
#define CONFIG_SYS_PCIE4_MEM_PHYS   0xc30000000ull
#define CONFIG_SYS_PCIE4_MEM_SIZE   0x10000000  /* 256M */
#define CONFIG_SYS_PCIE4_IO_VIRT    0xf8030000
#define CONFIG_SYS_PCIE4_IO_BUS     0x00000000
#define CONFIG_SYS_PCIE4_IO_PHYS    0xff8030000ull
#define CONFIG_SYS_PCIE4_IO_SIZE    0x00010000  /* 64k */
#endif

#define CONFIG_E1000
#define CONFIG_E1000_SPI
#define CONFIG_CMD_E1000

#define CONFIG_PCI_SCAN_SHOW        /* show pci devices on startup */
/* #define CONFIG_DOS_PARTITION */
#endif  /* CONFIG_PCI */

/*
 * SATA 
 */
#define CONFIG_FSL_SATA_V2
#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA

#define CONFIG_SYS_SATA_MAX_DEVICE  2

#define CONFIG_SATA1
#define CONFIG_SYS_SATA1            CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS      FLAGS_DMA

#define CONFIG_SATA2
#define CONFIG_SYS_SATA2            CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS      FLAGS_DMA

#define CONFIG_LBA48
/* #define CONFIG_DOS_PARTITION */
#endif

#define CONFIG_SPI_FLASH_MTD

/*
 * USB
 */
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#if (__BYTE_ORDER__ == __ORDER_BIG_ENDIAN__)
#define CONFIG_EHCI_DESC_BIG_ENDIAN /* Endiannes fix for EHCI USB */
#endif
#endif

/*
 * SDHC
 */
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
/*#define CONFIG_CMD_MMC*/
/* #define CONFIG_GENERIC_MMC */
#define CONFIG_CMD_EXT2
/*#define CONFIG_CMD_FAT*/
/* #define CONFIG_DOS_PARTITION */
#endif

/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS     10
#define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08

#define CONFIG_SYS_QMAN_NUM_PORTALS     10
#define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
#define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
#define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08

#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME


#define CONFIG_QE
#define CONFIG_U_QE

/* Default address of microcode for the Linux Fman driver */
/* TODO: move FMAN/QE ucode to boot source */

#if defined(CONFIG_SDHC_FLASH_BOOT)
/* 
 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 */
/*#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
#define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
#define CONFIG_SYS_QE_FW_ADDR			(512 * 0x920)*/
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_FMAN_FW_ADDR		(0x240000)	/* Refer to mtdparts: fman_ucode */
#define CONFIG_SYS_QE_FW_ADDR		(0x280000)	/* Refer to mtdparts: qe_ucode */

#elif defined(CONFIG_NAND_FLASH_BOOT)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_FMAN_FW_ADDR		(0x240000)	/* Refer to mtdparts: fman_ucode */
#define CONFIG_SYS_QE_FW_ADDR		(0x280000)	/* Refer to mtdparts: qe_ucode */

#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR		0xe8240000	/* Refer to mtdparts: fman_ucode */
#define CONFIG_SYS_QE_FW_ADDR  		0xe8280000	/* Refer to mtdparts: qe_ucode */
/* __stringify(CONFIG_LOADADDR) */
#endif

#define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
#define CONFIG_SYS_FDT_PAD      (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */

#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
/*#define CONFIG_PHY_MARVELL*/
#endif

#ifdef CONFIG_FMAN_ENET
#define CONFIG_SYS_RGMII1_PHY_ADDR      0x00
#define CONFIG_SYS_RGMII2_PHY_ADDR      0x01

#define CONFIG_MII          /* MII PHY management */
#define CONFIG_ETHPRIME     "FM1@DTSEC4"
#define CONFIG_PHY_GIGE     /* Include GbE speed/duplex detection */
#endif

/*
 * Environment
 */
#define CONFIG_LOADS_ECHO               /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */

/*
 * Command line configuration.
 */
/*#define CONFIG_CMD_ERRATA*/
#define CONFIG_CMD_GREPENV
/*#define CONFIG_CMD_IRQ*/
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
/*#define CONFIG_CMD_REGINFO*/

#ifdef CONFIG_PCI
/*#define CONFIG_CMD_PCI*/
#endif

/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
/*#define CONFIG_CMD_HASH*/
#define CONFIG_SHA_HW_ACCEL
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
#define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR	1000000		/* default load address */
#define CONFIG_SYS_PROMPT	"=> "           /* Monitor Command Prompt */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE	512		/* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS	32		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20)  /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)  /* Increase max gunzip size */

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#endif

/*
 * Dynamic MTD Partition support with mtdparts
 */
/*#define CONFIG_CMD_MTDPARTS*/
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_NOR_FLASH

/*#define CONFIG_SYS_NO_FLASH*/


#ifdef CONFIG_SECURE_BOOT
#include <asm/fsl_secure_boot.h>
#define CONFIG_CMD_BLOB
#endif

#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
/* #define CONFIG_UBI_SILENCE_MSG */
#define CONFIG_RBTREE
#define CONFIG_LZO

/*
 * eSPI - Enhanced SPI
 */
#if defined(CONFIG_SPI_FLASH)
#define CONFIG_FSL_ESPI

#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SPI_FLASH_SPANSION

/*#define CONFIG_CMD_SF*/
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED	10000000
#define CONFIG_SF_DEFAULT_MODE	0
#endif

#define MTDIDS_DEFAULT \
	"nand0=fff800000.flash," \
	"nor0=fe8000000.nor"

#define MTDPART_DEFAULT_PARTITIONS \
	"2M@0x0(u-boot)," \
	"256k(env)," \
	"256k(fman_ucode)," \
	"256k(qe_ucode),"


#ifdef CONFIG_NAND_FLASH

#endif
#ifdef CONFIG_NOR_FLASH
	
#endif
#define MTDPARTS_DEFAULT    \
	"mtdparts=fff800000.flash:" \
		MTDPART_DEFAULT_PARTITIONS \
		"0x3fc80000(ubipart_nand)," \
		"1M@0x3ff00000(bbt)ro;" \
	"fe8000000.nor:" \
		MTDPART_DEFAULT_PARTITIONS \
		"-(ubipart_nor)"

#ifdef CONFIG_NOR_FLASH
#define NOR_ENV	\
	"update-uboot-nor-nw=" \
		"dhcp; tftp ${TFTP_PATH}/u-boot-with-spl-pbl.bin.nor;" \
		"if test $? = \"0\"; then " \
			"protect off 0xe8000000 0xe81fffff;" \
			"erase 0xe8000000 0xe81fffff;" \
			"cp.w ${loadaddr} 0xe8000000 ${filesize};" \
		"fi\0" \
	"update-uboot-nor-usb=" \
		"usb start;" \
		"fatload usb 0 ${loadaddr} u-boot-with-spl-pbl.bin.nor;" \
		"if test $? = \"0\"; then " \
			"protect off 0xe8000000 0xe81fffff;" \
			"erase 0xe8000000 0xe81fffff;" \
			"cp.w ${loadaddr} 0xe8000000 ${filesize};" \
		"fi\0" \
	\
	"update-fman-ucode-nor-usb=" \
		"usb start;" \
		"fatload usb 0 ${loadaddr} fsl_fman_ucode_t1040_r1.1_106_4_17.bin;" \
		"if test $? = \"0\"; then " \
			"protect off 0xe8240000 0xe827ffff;" \
			"erase 0xe8240000 0xe827ffff;" \
			"cp.w ${loadaddr} 0xe8240000 ${filesize};" \
		"fi\0" \
	"update-qe-ucode-nor-usb=" \
		"usb start;" \
		"fatload usb 0 ${loadaddr} iram_Type_A_T1040_r1.0.bin;" \
		"if test $? = \"0\"; then " \
			"protect off 0xe8280000 0xe82bffff;" \
			"erase 0xe8280000 0xe82bffff;" \
			"cp.w ${loadaddr} 0xe8280000 ${filesize};" \
		"fi\0" \
	"update-ubi-rootfs-nor="\
		"dhcp;" \
		"ubi part ubipart_nor;" \
		"if test $? = \"0\"; then " \
			"tftp ${TFTP_PATH}/ubi_rootfs_image.nor.ubifs;" \
			"if test $? = \"0\"; then " \
				"ubi write ${loadaddr} rootfs ${filesize};" \
			"fi;" \
		"fi;" \
		"\0" \
	\
	"ubiboot-nor=" \
		"ubi part ubipart_nor;" \
		"ubifsmount ubi0:rootfs;" \
		"ubifsload ${fitaddr} /boot/fitImage.itb;" \
		"run set_ubiboot_args_nor;" \
		"bootm ${fitaddr}#conf@1" \
		"\0" \
	\
	"set_ubiboot_args_nor=setenv bootargs ${bootargs} ${mtdparts} ubi.mtd=ubipart_nor ubi.fm_autoconvert=1 root=ubi0:rootfs rw rootfstype=ubifs \0"
#else
#define NOR_ENV
#endif

#ifdef CONFIG_NAND_FLASH
#define NAND_ENV \
    "update-uboot-nand-nw=" \
        "dhcp;" \
        "tftp ${TFTP_PATH}/u-boot-with-spl-pbl.bin.nand;" \
        "if test $? = \"0\"; then " \
            "nand erase.part u-boot;" \
            "nand write ${loadaddr} 0 ${filesize}; "\
        "fi\0" \
    "update-uboot-nand-usb=" \
        "usb start;" \
        "fatload usb 0 ${loadaddr} u-boot-with-spl-pbl.bin.nand;" \
        "nand erase.part u-boot;" \
        "nand write ${loadaddr} u-boot ${filesize};" \
        "\0" \
    \
    "update-fman-ucode-nand-usb=" \
        "usb start;" \
        "fatload usb 0 ${loadaddr} fsl_fman_ucode_t1040_r1.1_106_4_17.bin;" \
        "nand erase.part fman_ucode;" \
        "nand write ${loadaddr} fman_ucode ${filesize};" \
        "\0" \
    \
    "update-qe-ucode-nand-usb=" \
        "usb start;" \
        "fatload usb 0 ${loadaddr} iram_Type_A_T1040_r1.0.bin;" \
        "nand erase.part qe_ucode;" \
        "nand write ${loadaddr} qe_ucode ${filesize};" \
        "\0" \
    "update-ubi-rootfs-nand="\
        "dhcp;" \
        "ubi part ubipart_nand;" \
        "if test $? = \"0\"; then " \
            "tftp ${TFTP_PATH}/ubi_rootfs_image.nand.ubifs;" \
            "if test $? = \"0\"; then " \
                "ubi write ${loadaddr} rootfs ${filesize};" \
            "fi;" \
        "fi;" \
    "\0" \
    \
    "ubiboot-nand=" \
        "ubi part ubipart_nand;" \
        "ubifsmount ubi0:rootfs;" \
        "ubifsload ${fitaddr} /boot/fitImage.itb;" \
        "run set_ubiboot_args_nand;" \
        "bootm ${fitaddr}#conf@1" \
        "\0" \
    \
    "set_ubiboot_args_nand=setenv bootargs ${bootargs} ${mtdparts} ubi.mtd=ubipart_nand ubi.fm_autoconvert=1 root=ubi0:rootfs rw rootfstype=ubifs \0"
#else
#define NAND_ENV
#endif

#ifdef CONFIG_NAND_FLASH_BOOT
#define BOOTCMD "ubiboot-nand"
#elif defined(CONFIG_NOR_FLASH_BOOT)
#define BOOTCMD "ubiboot-nor"
#else
#define BOOTCMD ""
#endif

/* default location for tftp and bootm */
#define CONFIG_LOADADDR		1000000
#define CONFIG_BAUDRATE		115200


#define __USB_PHY_TYPE  utmi

#define CONFIG_EXTRA_ENV_SETTINGS \
    "hwconfig=" \
        "fsl_ddr:bank_intlv=null;"\
        "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
        "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
    \
    "l2switchaddr=02:00:00:ba:be:00\0" \
    "ethaddr=02:00:00:ba:be:01\0" \
    "eth1addr=02:00:00:ba:be:02\0" \
    "eth2addr=02:00:00:ba:be:03\0" \
    "eth3addr=02:00:00:ba:be:04\0" \
    "eth4addr=02:00:00:ba:be:05\0" \
    \
    "autoload=no\0" \
    "fitaddr="__stringify(CONFIG_LOADADDR)"\0" \
    "TFTP_PATH=\0" \
    \
    "mtdids=" MTDIDS_DEFAULT "\0" \
    "mtdparts=" MTDPARTS_DEFAULT "\0" \
    \
    NOR_ENV \
    NAND_ENV \
    \
    "setfans=i2c dev 0; i2c mw 0x2e 0x40 1;i2c mw 0x2e 0x7d 0x2;" \
        "i2c mw 0x2e 0x5c 0xe0;i2c mw 0x2e 0x5d 0xe0;i2c mw 0x2e 0x5e 0xe0;" \
        "i2c mw 0x2e 0x5f 0xc8;i2c mw 0x2e 0x60 0xc8;i2c mw 0x2e 0x61 0xc8;" \
        "i2c mw 0x2e 0x30 0x20;i2c mw 0x2e 0x31 0x20;i2c mw 0x2e 0x32 0x20;\0"\
    \
    "probe-spi-flash=sf probe 0; if test $? = \"0\"; then " \
	"setenv mtdids \"${mtdids}\",nor1=fe110000.spi;" \
	"setenv mtdparts \"${mtdparts};\"fe110000.spi:" MTDPART_DEFAULT_PARTITIONS "-(storage);"\
	";fi\0" \
    \
    "netboot=dhcp; tftp ${fitaddr} ${TFTP_PATH}/fitImage.itb; bootm ${fitaddr}#conf@1\0" \
    \
    "bootcmd=run setfans; run "BOOTCMD"\0" \
    \
    "bootargs_sata=rootfstype=ext3 root=/dev/sda1\0" \
    "bootargs=console=ttyS0,115200 rootwait panic=10\0" \

#endif	/* SIMC_T10XX_H */