Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (124 commits)
  sh: allow building for both r2d boards in same binary.
  sh: fix r2d board detection
  sh: Discard .exit.text/.exit.data at runtime.
  sh: Fix up some section alignments in linker script.
  sh: Fix SH-4 DMAC CHCR masking.
  sh: Rip out left-over nommu cond syscall cruft.
  sh: Make kgdb i-cache flushing less inept.
  sh: kgdb section mismatches and tidying.
  sh: cleanup struct irqaction initializers.
  sh: early_printk tidying.
  video: pvr2fb: Add TV (RGB) support to Dreamcast PVR driver.
  sh: Conditionalize gUSA support.
  sh: Follow gUSA preempt changes in __switch_to().
  sh: Tidy up gUSA preempt handling.
  sh: __copy_user() optimizations for small copies.
  sh: clkfwk: Support multi-level clock propagation.
  sh: Fix URAM start address on SH7785.
  sh: Use boot_cpu_data for CPU probe.
  sh: Support extended mode TLB on SH-X3.
  sh: Bump MAX_ACTIVE_REGIONS for SH7785.
  ...

1 files changed, 35 insertions, 4 deletions

diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index 053fca4..73440e2 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -4,6 +4,7 @@
  * SuperH on-chip serial module support.  (SCI with no FIFO / with FIFO)
  *
  *  Copyright (C) 2002 - 2006  Paul Mundt
+ *  Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
  *
  * based off of the old drivers/char/sh-sci.c by:
  *
@@ -301,6 +302,38 @@ static void sci_init_pins_scif(struct uart_port* port, unsigned int cflag)
 	}
 	sci_out(port, SCFCR, fcr_val);
 }
+#elif defined(CONFIG_CPU_SUBTYPE_SH7720)
+static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
+{
+	unsigned int fcr_val = 0;
+	unsigned short data;
+
+	if (cflag & CRTSCTS) {
+		/* enable RTS/CTS */
+		if (port->mapbase == 0xa4430000) { /* SCIF0 */
+			/* Clear PTCR bit 9-2; enable all scif pins but sck */
+			data = ctrl_inw(PORT_PTCR);
+			ctrl_outw((data & 0xfc03), PORT_PTCR);
+		} else if (port->mapbase == 0xa4438000) { /* SCIF1 */
+			/* Clear PVCR bit 9-2 */
+			data = ctrl_inw(PORT_PVCR);
+			ctrl_outw((data & 0xfc03), PORT_PVCR);
+		}
+		fcr_val |= SCFCR_MCE;
+	} else {
+		if (port->mapbase == 0xa4430000) { /* SCIF0 */
+			/* Clear PTCR bit 5-2; enable only tx and rx  */
+			data = ctrl_inw(PORT_PTCR);
+			ctrl_outw((data & 0xffc3), PORT_PTCR);
+		} else if (port->mapbase == 0xa4438000) { /* SCIF1 */
+			/* Clear PVCR bit 5-2 */
+			data = ctrl_inw(PORT_PVCR);
+			ctrl_outw((data & 0xffc3), PORT_PVCR);
+		}
+	}
+	sci_out(port, SCFCR, fcr_val);
+}
+
 #elif defined(CONFIG_CPU_SH3)
 /* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
@@ -1276,7 +1309,7 @@ static int __init sci_console_init(void)
 console_initcall(sci_console_init);
 #endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
 
-#ifdef CONFIG_SH_KGDB
+#ifdef CONFIG_SH_KGDB_CONSOLE
 /*
  * FIXME: Most of this can go away.. at the moment, we rely on
  * arch/sh/kernel/setup.c to do the command line parsing for kgdb, though
@@ -1334,9 +1367,7 @@ int __init kgdb_console_setup(struct console *co, char *options)
 
 	return uart_set_options(port, co, baud, parity, bits, flow);
 }
-#endif /* CONFIG_SH_KGDB */
 
-#ifdef CONFIG_SH_KGDB_CONSOLE
 static struct console kgdb_console = {
 	.name		= "ttySC",
 	.device		= uart_console_device,
@@ -1432,7 +1463,7 @@ static int __devinit sci_probe(struct platform_device *dev)
 
 #ifdef CONFIG_CPU_FREQ
 	cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
-	dev_info(&dev->dev, "sci: CPU frequency notifier registered\n");
+	dev_info(&dev->dev, "CPU frequency notifier registered\n");
 #endif
 
 #ifdef CONFIG_SH_STANDARD_BIOS