diff options
-rw-r--r-- | drivers/net/e1000e/e1000.h | 6 | ||||
-rw-r--r-- | drivers/net/e1000e/ich8lan.c | 216 | ||||
-rw-r--r-- | drivers/net/e1000e/phy.c | 191 |
3 files changed, 204 insertions, 209 deletions
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h index b9f9e78..cebbd90 100644 --- a/drivers/net/e1000e/e1000.h +++ b/drivers/net/e1000e/e1000.h @@ -590,6 +590,12 @@ extern s32 e1000_get_phy_info_82577(struct e1000_hw *hw); extern s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw); extern s32 e1000_get_cable_length_82577(struct e1000_hw *hw); +extern s32 e1000_check_polarity_m88(struct e1000_hw *hw); +extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw); +extern s32 e1000_check_polarity_ife(struct e1000_hw *hw); +extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw); +extern s32 e1000_check_polarity_igp(struct e1000_hw *hw); + static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw) { return hw->phy.ops.reset(hw); diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 6efb77f..7b33be9 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -195,7 +195,6 @@ union ich8_flash_protected_range { static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw); static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw); static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw); -static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw); static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank); static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, u8 byte); @@ -260,7 +259,6 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw) phy->addr = 1; phy->reset_delay_us = 100; - phy->ops.check_polarity = e1000_check_polarity_ife_ich8lan; phy->ops.read_reg = e1000_read_phy_reg_hv; phy->ops.read_reg_locked = e1000_read_phy_reg_hv_locked; phy->ops.set_d0_lplu_state = e1000_set_lplu_state_pchlan; @@ -275,13 +273,23 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw) e1000e_get_phy_id(hw); phy->type = e1000e_get_phy_type_from_id(phy->id); - if (phy->type == e1000_phy_82577) { + switch (phy->type) { + case e1000_phy_82577: phy->ops.check_polarity = e1000_check_polarity_82577; phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_82577; - phy->ops.get_cable_length = e1000_get_cable_length_82577; + phy->ops.get_cable_length = e1000_get_cable_length_82577; phy->ops.get_info = e1000_get_phy_info_82577; phy->ops.commit = e1000e_phy_sw_reset; + case e1000_phy_82578: + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_m88; + phy->ops.get_cable_length = e1000e_get_cable_length_m88; + phy->ops.get_info = e1000e_get_phy_info_m88; + break; + default: + ret_val = -E1000_ERR_PHY; + break; } return ret_val; @@ -336,12 +344,18 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; phy->ops.read_reg_locked = e1000e_read_phy_reg_igp_locked; phy->ops.write_reg_locked = e1000e_write_phy_reg_igp_locked; + phy->ops.get_info = e1000e_get_phy_info_igp; + phy->ops.check_polarity = e1000_check_polarity_igp; + phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_igp; break; case IFE_E_PHY_ID: case IFE_PLUS_E_PHY_ID: case IFE_C_E_PHY_ID: phy->type = e1000_phy_ife; phy->autoneg_mask = E1000_ALL_NOT_GIG; + phy->ops.get_info = e1000_get_phy_info_ife; + phy->ops.check_polarity = e1000_check_polarity_ife; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_ife; break; case BME1000_E_PHY_ID: phy->type = e1000_phy_bm; @@ -349,14 +363,15 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) phy->ops.read_reg = e1000e_read_phy_reg_bm; phy->ops.write_reg = e1000e_write_phy_reg_bm; phy->ops.commit = e1000e_phy_sw_reset; + phy->ops.get_info = e1000e_get_phy_info_m88; + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_m88; break; default: return -E1000_ERR_PHY; break; } - phy->ops.check_polarity = e1000_check_polarity_ife_ich8lan; - return 0; } @@ -740,77 +755,6 @@ static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw) } /** - * e1000_phy_force_speed_duplex_ich8lan - Force PHY speed & duplex - * @hw: pointer to the HW structure - * - * Forces the speed and duplex settings of the PHY. - * This is a function pointer entry point only called by - * PHY setup routines. - **/ -static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 data; - bool link; - - if (phy->type != e1000_phy_ife) { - ret_val = e1000e_phy_force_speed_duplex_igp(hw); - return ret_val; - } - - ret_val = e1e_rphy(hw, PHY_CONTROL, &data); - if (ret_val) - return ret_val; - - e1000e_phy_force_speed_duplex_setup(hw, &data); - - ret_val = e1e_wphy(hw, PHY_CONTROL, data); - if (ret_val) - return ret_val; - - /* Disable MDI-X support for 10/100 */ - ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); - if (ret_val) - return ret_val; - - data &= ~IFE_PMC_AUTO_MDIX; - data &= ~IFE_PMC_FORCE_MDIX; - - ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data); - if (ret_val) - return ret_val; - - e_dbg("IFE PMC: %X\n", data); - - udelay(1); - - if (phy->autoneg_wait_to_complete) { - e_dbg("Waiting for forced speed/duplex link on IFE phy.\n"); - - ret_val = e1000e_phy_has_link_generic(hw, - PHY_FORCE_LIMIT, - 100000, - &link); - if (ret_val) - return ret_val; - - if (!link) - e_dbg("Link taking longer than expected.\n"); - - /* Try once more */ - ret_val = e1000e_phy_has_link_generic(hw, - PHY_FORCE_LIMIT, - 100000, - &link); - if (ret_val) - return ret_val; - } - - return 0; -} - -/** * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration * @hw: pointer to the HW structure * @@ -1262,122 +1206,6 @@ out: } /** - * e1000_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states - * @hw: pointer to the HW structure - * - * Populates "phy" structure with various feature states. - * This function is only called by other family-specific - * routines. - **/ -static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 data; - bool link; - - ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); - if (ret_val) - return ret_val; - - if (!link) { - e_dbg("Phy info is only valid if link is up\n"); - return -E1000_ERR_CONFIG; - } - - ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data); - if (ret_val) - return ret_val; - phy->polarity_correction = (!(data & IFE_PSC_AUTO_POLARITY_DISABLE)); - - if (phy->polarity_correction) { - ret_val = phy->ops.check_polarity(hw); - if (ret_val) - return ret_val; - } else { - /* Polarity is forced */ - phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY) - ? e1000_rev_polarity_reversed - : e1000_rev_polarity_normal; - } - - ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); - if (ret_val) - return ret_val; - - phy->is_mdix = (data & IFE_PMC_MDIX_STATUS); - - /* The following parameters are undefined for 10/100 operation. */ - phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; - phy->local_rx = e1000_1000t_rx_status_undefined; - phy->remote_rx = e1000_1000t_rx_status_undefined; - - return 0; -} - -/** - * e1000_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info - * @hw: pointer to the HW structure - * - * Wrapper for calling the get_phy_info routines for the appropriate phy type. - * This is a function pointer entry point called by drivers - * or other shared routines. - **/ -static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw) -{ - switch (hw->phy.type) { - case e1000_phy_ife: - return e1000_get_phy_info_ife_ich8lan(hw); - break; - case e1000_phy_igp_3: - case e1000_phy_bm: - case e1000_phy_82578: - case e1000_phy_82577: - return e1000e_get_phy_info_igp(hw); - break; - default: - break; - } - - return -E1000_ERR_PHY_TYPE; -} - -/** - * e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY - * @hw: pointer to the HW structure - * - * Polarity is determined on the polarity reversal feature being enabled. - * This function is only called by other family-specific - * routines. - **/ -static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 phy_data, offset, mask; - - /* - * Polarity is determined based on the reversal feature being enabled. - */ - if (phy->polarity_correction) { - offset = IFE_PHY_EXTENDED_STATUS_CONTROL; - mask = IFE_PESC_POLARITY_REVERSED; - } else { - offset = IFE_PHY_SPECIAL_CONTROL; - mask = IFE_PSC_FORCE_POLARITY; - } - - ret_val = e1e_rphy(hw, offset, &phy_data); - - if (!ret_val) - phy->cable_polarity = (phy_data & mask) - ? e1000_rev_polarity_reversed - : e1000_rev_polarity_normal; - - return ret_val; -} - -/** * e1000_set_lplu_state_pchlan - Set Low Power Link Up state * @hw: pointer to the HW structure * @active: true to enable LPLU, false to disable @@ -3485,10 +3313,8 @@ static struct e1000_phy_operations ich8_phy_ops = { .acquire = e1000_acquire_swflag_ich8lan, .check_reset_block = e1000_check_reset_block_ich8lan, .commit = NULL, - .force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan, .get_cfg_done = e1000_get_cfg_done_ich8lan, .get_cable_length = e1000e_get_cable_length_igp_2, - .get_info = e1000_get_phy_info_ich8lan, .read_reg = e1000e_read_phy_reg_igp, .release = e1000_release_swflag_ich8lan, .reset = e1000_phy_hw_reset_ich8lan, diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c index 67a7188..55a2c0a 100644 --- a/drivers/net/e1000e/phy.c +++ b/drivers/net/e1000e/phy.c @@ -1322,17 +1322,22 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw) return ret_val; if (!link) { - /* - * We didn't get link. - * Reset the DSP and cross our fingers. - */ - ret_val = e1e_wphy(hw, M88E1000_PHY_PAGE_SELECT, - 0x001d); - if (ret_val) - return ret_val; - ret_val = e1000e_phy_reset_dsp(hw); - if (ret_val) - return ret_val; + if (hw->phy.type != e1000_phy_m88) { + e_dbg("Link taking longer than expected.\n"); + } else { + /* + * We didn't get link. + * Reset the DSP and cross our fingers. + */ + ret_val = e1e_wphy(hw, + M88E1000_PHY_PAGE_SELECT, + 0x001d); + if (ret_val) + return ret_val; + ret_val = e1000e_phy_reset_dsp(hw); + if (ret_val) + return ret_val; + } } /* Try once more */ @@ -1342,6 +1347,9 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw) return ret_val; } + if (hw->phy.type != e1000_phy_m88) + return 0; + ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); if (ret_val) return ret_val; @@ -1371,6 +1379,73 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw) } /** + * e1000_phy_force_speed_duplex_ife - Force PHY speed & duplex + * @hw: pointer to the HW structure + * + * Forces the speed and duplex settings of the PHY. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + ret_val = e1e_rphy(hw, PHY_CONTROL, &data); + if (ret_val) + goto out; + + e1000e_phy_force_speed_duplex_setup(hw, &data); + + ret_val = e1e_wphy(hw, PHY_CONTROL, data); + if (ret_val) + goto out; + + /* Disable MDI-X support for 10/100 */ + ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); + if (ret_val) + goto out; + + data &= ~IFE_PMC_AUTO_MDIX; + data &= ~IFE_PMC_FORCE_MDIX; + + ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data); + if (ret_val) + goto out; + + e_dbg("IFE PMC: %X\n", data); + + udelay(1); + + if (phy->autoneg_wait_to_complete) { + e_dbg("Waiting for forced speed/duplex link on IFE phy.\n"); + + ret_val = e1000e_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + + if (!link) + e_dbg("Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = e1000e_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** * e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex * @hw: pointer to the HW structure * @phy_ctrl: pointer to current value of PHY_CONTROL @@ -1557,7 +1632,7 @@ s32 e1000e_check_downshift(struct e1000_hw *hw) * * Polarity is determined based on the PHY specific status register. **/ -static s32 e1000_check_polarity_m88(struct e1000_hw *hw) +s32 e1000_check_polarity_m88(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val; @@ -1582,7 +1657,7 @@ static s32 e1000_check_polarity_m88(struct e1000_hw *hw) * Polarity is determined based on the PHY port status register, and the * current speed (since there is no polarity at 100Mbps). **/ -static s32 e1000_check_polarity_igp(struct e1000_hw *hw) +s32 e1000_check_polarity_igp(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val; @@ -1620,6 +1695,39 @@ static s32 e1000_check_polarity_igp(struct e1000_hw *hw) } /** + * e1000_check_polarity_ife - Check cable polarity for IFE PHY + * @hw: pointer to the HW structure + * + * Polarity is determined on the polarity reversal feature being enabled. + **/ +s32 e1000_check_polarity_ife(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, offset, mask; + + /* + * Polarity is determined based on the reversal feature being enabled. + */ + if (phy->polarity_correction) { + offset = IFE_PHY_EXTENDED_STATUS_CONTROL; + mask = IFE_PESC_POLARITY_REVERSED; + } else { + offset = IFE_PHY_SPECIAL_CONTROL; + mask = IFE_PSC_FORCE_POLARITY; + } + + ret_val = e1e_rphy(hw, offset, &phy_data); + + if (!ret_val) + phy->cable_polarity = (phy_data & mask) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** * e1000_wait_autoneg - Wait for auto-neg completion * @hw: pointer to the HW structure * @@ -1823,7 +1931,7 @@ s32 e1000e_get_phy_info_m88(struct e1000_hw *hw) u16 phy_data; bool link; - if (hw->phy.media_type != e1000_media_type_copper) { + if (phy->media_type != e1000_media_type_copper) { e_dbg("Phy info is only valid for copper media\n"); return -E1000_ERR_CONFIG; } @@ -1944,6 +2052,61 @@ s32 e1000e_get_phy_info_igp(struct e1000_hw *hw) } /** + * e1000_get_phy_info_ife - Retrieves various IFE PHY states + * @hw: pointer to the HW structure + * + * Populates "phy" structure with various feature states. + **/ +s32 e1000_get_phy_info_ife(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + e_dbg("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data); + if (ret_val) + goto out; + phy->polarity_correction = (data & IFE_PSC_AUTO_POLARITY_DISABLE) + ? false : true; + + if (phy->polarity_correction) { + ret_val = e1000_check_polarity_ife(hw); + if (ret_val) + goto out; + } else { + /* Polarity is forced */ + phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + } + + ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); + if (ret_val) + goto out; + + phy->is_mdix = (data & IFE_PMC_MDIX_STATUS) ? true : false; + + /* The following parameters are undefined for 10/100 operation. */ + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + +out: + return ret_val; +} + +/** * e1000e_phy_sw_reset - PHY software reset * @hw: pointer to the HW structure * |