diff options
| -rw-r--r-- | Documentation/IPMI.txt | 65 | ||||
| -rw-r--r-- | MAINTAINERS | 2 | ||||
| -rw-r--r-- | arch/arm/mach-prima2/include/mach/gpio.h | 13 | ||||
| -rw-r--r-- | drivers/Makefile | 4 | ||||
| -rw-r--r-- | drivers/acpi/Makefile | 5 | ||||
| -rw-r--r-- | drivers/char/Makefile | 1 | ||||
| -rw-r--r-- | drivers/char/ipmi/ipmi_msghandler.c | 2 | ||||
| -rw-r--r-- | drivers/char/ipmi/ipmi_si_intf.c | 36 | ||||
| -rw-r--r-- | drivers/pinctrl/pinctrl-bcm2835.c | 5 | ||||
| -rw-r--r-- | drivers/pinctrl/pinctrl-nomadik.c | 26 | ||||
| -rw-r--r-- | drivers/pinctrl/pinctrl-samsung.c | 10 | ||||
| -rw-r--r-- | drivers/pinctrl/pinctrl-sirf.c | 35 | ||||
| -rw-r--r-- | drivers/pinctrl/pinctrl-xway.c | 2 | ||||
| -rw-r--r-- | fs/proc/task_mmu.c | 7 | ||||
| -rw-r--r-- | mm/mempolicy.c | 5 |
15 files changed, 77 insertions, 141 deletions
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index b2bea15..16eb4c9 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -42,13 +42,7 @@ The driver interface depends on your hardware. If your system properly provides the SMBIOS info for IPMI, the driver will detect it and just work. If you have a board with a standard interface (These will generally be either "KCS", "SMIC", or "BT", consult your hardware -manual), choose the 'IPMI SI handler' option. A driver also exists -for direct I2C access to the IPMI management controller. Some boards -support this, but it is unknown if it will work on every board. For -this, choose 'IPMI SMBus handler', but be ready to try to do some -figuring to see if it will work on your system if the SMBIOS/APCI -information is wrong or not present. It is fairly safe to have both -these enabled and let the drivers auto-detect what is present. +manual), choose the 'IPMI SI handler' option. You should generally enable ACPI on your system, as systems with IPMI can have ACPI tables describing them. @@ -58,8 +52,7 @@ their job correctly, the IPMI controller should be automatically detected (via ACPI or SMBIOS tables) and should just work. Sadly, many boards do not have this information. The driver attempts standard defaults, but they may not work. If you fall into this -situation, you need to read the section below named 'The SI Driver' or -"The SMBus Driver" on how to hand-configure your system. +situation, you need to read the section below named 'The SI Driver'. IPMI defines a standard watchdog timer. You can enable this with the 'IPMI Watchdog Timer' config option. If you compile the driver into @@ -104,12 +97,7 @@ driver, each open file for this device ties in to the message handler as an IPMI user. ipmi_si - A driver for various system interfaces. This supports KCS, -SMIC, and BT interfaces. Unless you have an SMBus interface or your -own custom interface, you probably need to use this. - -ipmi_smb - A driver for accessing BMCs on the SMBus. It uses the -I2C kernel driver's SMBus interfaces to send and receive IPMI messages -over the SMBus. +SMIC, and BT interfaces. ipmi_watchdog - IPMI requires systems to have a very capable watchdog timer. This driver implements the standard Linux watchdog timer @@ -482,53 +470,6 @@ for specifying an interface. Note that when removing an interface, only the first three parameters (si type, address type, and address) are used for the comparison. Any options are ignored for removing. -The SMBus Driver ----------------- - -The SMBus driver allows up to 4 SMBus devices to be configured in the -system. By default, the driver will register any SMBus interfaces it finds -in the I2C address range of 0x20 to 0x4f on any adapter. You can change this -at module load time (for a module) with: - - modprobe ipmi_smb.o - addr=<adapter1>,<i2caddr1>[,<adapter2>,<i2caddr2>[,...]] - dbg=<flags1>,<flags2>... - [defaultprobe=1] [dbg_probe=1] - -The addresses are specified in pairs, the first is the adapter ID and the -second is the I2C address on that adapter. - -The debug flags are bit flags for each BMC found, they are: -IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8 - -Setting smb_defaultprobe to zero disabled the default probing of SMBus -interfaces at address range 0x20 to 0x4f. This means that only the -BMCs specified on the smb_addr line will be detected. - -Setting smb_dbg_probe to 1 will enable debugging of the probing and -detection process for BMCs on the SMBusses. - -Discovering the IPMI compliant BMC on the SMBus can cause devices -on the I2C bus to fail. The SMBus driver writes a "Get Device ID" IPMI -message as a block write to the I2C bus and waits for a response. -This action can be detrimental to some I2C devices. It is highly recommended -that the known I2c address be given to the SMBus driver in the smb_addr -parameter. The default address range will not be used when a smb_addr -parameter is provided. - -When compiled into the kernel, the addresses can be specified on the -kernel command line as: - - ipmb_smb.addr=<adapter1>,<i2caddr1>[,<adapter2>,<i2caddr2>[,...]] - ipmi_smb.dbg=<flags1>,<flags2>... - ipmi_smb.defaultprobe=0 ipmi_smb.dbg_probe=1 - -These are the same options as on the module command line. - -Note that you might need some I2C changes if CONFIG_IPMI_PANIC_EVENT -is enabled along with this, so the I2C driver knows to run to -completion during sending a panic event. - Other Pieces ------------ diff --git a/MAINTAINERS b/MAINTAINERS index e73060f..e39e9da 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4372,7 +4372,7 @@ F: Documentation/scsi/53c700.txt F: drivers/scsi/53c700* LED SUBSYSTEM -M: Bryan Wu <bryan.wu@canonical.com> +M: Bryan Wu <cooloney@gmail.com> M: Richard Purdie <rpurdie@rpsys.net> L: linux-leds@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds.git diff --git a/arch/arm/mach-prima2/include/mach/gpio.h b/arch/arm/mach-prima2/include/mach/gpio.h deleted file mode 100644 index 1904bb0..0000000 --- a/arch/arm/mach-prima2/include/mach/gpio.h +++ /dev/null @@ -1,13 +0,0 @@ -#ifndef __MACH_GPIO_H -#define __MACH_GPIO_H - -/* Pull up/down values */ -enum sirfsoc_gpio_pull { - SIRFSOC_GPIO_PULL_NONE, - SIRFSOC_GPIO_PULL_UP, - SIRFSOC_GPIO_PULL_DOWN, -}; - -void sirfsoc_gpio_set_pull(unsigned gpio, unsigned mode); - -#endif diff --git a/drivers/Makefile b/drivers/Makefile index 03da5b6..a16a8d0 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -17,6 +17,10 @@ obj-$(CONFIG_PARISC) += parisc/ obj-$(CONFIG_RAPIDIO) += rapidio/ obj-y += video/ obj-y += idle/ + +# IPMI must come before ACPI in order to provide IPMI opregion support +obj-$(CONFIG_IPMI_HANDLER) += char/ipmi/ + obj-$(CONFIG_ACPI) += acpi/ obj-$(CONFIG_SFI) += sfi/ # PnP must come after ACPI since it will eventually need to check if acpi diff --git a/drivers/acpi/Makefile b/drivers/acpi/Makefile index 47199e2..82422fe 100644 --- a/drivers/acpi/Makefile +++ b/drivers/acpi/Makefile @@ -47,6 +47,10 @@ acpi-y += video_detect.o endif # These are (potentially) separate modules + +# IPMI may be used by other drivers, so it has to initialise before them +obj-$(CONFIG_ACPI_IPMI) += acpi_ipmi.o + obj-$(CONFIG_ACPI_AC) += ac.o obj-$(CONFIG_ACPI_BUTTON) += button.o obj-$(CONFIG_ACPI_FAN) += fan.o @@ -70,6 +74,5 @@ processor-y += processor_idle.o processor_thermal.o processor-$(CONFIG_CPU_FREQ) += processor_perflib.o obj-$(CONFIG_ACPI_PROCESSOR_AGGREGATOR) += acpi_pad.o -obj-$(CONFIG_ACPI_IPMI) += acpi_ipmi.o obj-$(CONFIG_ACPI_APEI) += apei/ diff --git a/drivers/char/Makefile b/drivers/char/Makefile index d0b27a3..7ff1d0d 100644 --- a/drivers/char/Makefile +++ b/drivers/char/Makefile @@ -52,7 +52,6 @@ obj-$(CONFIG_TELCLOCK) += tlclk.o obj-$(CONFIG_MWAVE) += mwave/ obj-$(CONFIG_AGP) += agp/ obj-$(CONFIG_PCMCIA) += pcmcia/ -obj-$(CONFIG_IPMI_HANDLER) += ipmi/ obj-$(CONFIG_HANGCHECK_TIMER) += hangcheck-timer.o obj-$(CONFIG_TCG_TPM) += tpm/ diff --git a/drivers/char/ipmi/ipmi_msghandler.c b/drivers/char/ipmi/ipmi_msghandler.c index 2c29942..a0c84bb 100644 --- a/drivers/char/ipmi/ipmi_msghandler.c +++ b/drivers/char/ipmi/ipmi_msghandler.c @@ -1880,7 +1880,7 @@ int ipmi_request_supply_msgs(ipmi_user_t user, struct ipmi_recv_msg *supplied_recv, int priority) { - unsigned char saddr, lun; + unsigned char saddr = 0, lun = 0; int rv; if (!user) diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c index 83f85cf..32a6c7e 100644 --- a/drivers/char/ipmi/ipmi_si_intf.c +++ b/drivers/char/ipmi/ipmi_si_intf.c @@ -2424,6 +2424,38 @@ static void ipmi_pci_cleanup(struct smi_info *info) pci_disable_device(pdev); } +static int __devinit ipmi_pci_probe_regspacing(struct smi_info *info) +{ + if (info->si_type == SI_KCS) { + unsigned char status; + int regspacing; + + info->io.regsize = DEFAULT_REGSIZE; + info->io.regshift = 0; + info->io_size = 2; + info->handlers = &kcs_smi_handlers; + + /* detect 1, 4, 16byte spacing */ + for (regspacing = DEFAULT_REGSPACING; regspacing <= 16;) { + info->io.regspacing = regspacing; + if (info->io_setup(info)) { + dev_err(info->dev, + "Could not setup I/O space\n"); + return DEFAULT_REGSPACING; + } + /* write invalid cmd */ + info->io.outputb(&info->io, 1, 0x10); + /* read status back */ + status = info->io.inputb(&info->io, 1); + info->io_cleanup(info); + if (status) + return regspacing; + regspacing *= 4; + } + } + return DEFAULT_REGSPACING; +} + static int __devinit ipmi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { @@ -2476,8 +2508,8 @@ static int __devinit ipmi_pci_probe(struct pci_dev *pdev, } info->io.addr_data = pci_resource_start(pdev, 0); - info->io.regspacing = DEFAULT_REGSPACING; - info->io.regsize = DEFAULT_REGSPACING; + info->io.regspacing = ipmi_pci_probe_regspacing(info); + info->io.regsize = DEFAULT_REGSIZE; info->io.regshift = 0; info->irq = pdev->irq; diff --git a/drivers/pinctrl/pinctrl-bcm2835.c b/drivers/pinctrl/pinctrl-bcm2835.c index a4adee6..7e9be18 100644 --- a/drivers/pinctrl/pinctrl-bcm2835.c +++ b/drivers/pinctrl/pinctrl-bcm2835.c @@ -29,7 +29,6 @@ #include <linux/irq.h> #include <linux/irqdesc.h> #include <linux/irqdomain.h> -#include <linux/irq.h> #include <linux/module.h> #include <linux/of_address.h> #include <linux/of.h> @@ -960,7 +959,7 @@ static int __devinit bcm2835_pinctrl_probe(struct platform_device *pdev) return err; } - pc->base = devm_request_and_ioremap(&pdev->dev, &iomem); + pc->base = devm_request_and_ioremap(dev, &iomem); if (!pc->base) return -EADDRNOTAVAIL; @@ -1032,7 +1031,7 @@ static int __devinit bcm2835_pinctrl_probe(struct platform_device *pdev) pc->pctl_dev = pinctrl_register(&bcm2835_pinctrl_desc, dev, pc); if (!pc->pctl_dev) { gpiochip_remove(&pc->gpio_chip); - return PTR_ERR(pc->pctl_dev); + return -EINVAL; } pc->gpio_range = bcm2835_pinctrl_gpio_range; diff --git a/drivers/pinctrl/pinctrl-nomadik.c b/drivers/pinctrl/pinctrl-nomadik.c index fec9c30..01aea1c 100644 --- a/drivers/pinctrl/pinctrl-nomadik.c +++ b/drivers/pinctrl/pinctrl-nomadik.c @@ -30,7 +30,20 @@ #include <linux/pinctrl/pinconf.h> /* Since we request GPIOs from ourself */ #include <linux/pinctrl/consumer.h> +/* + * For the U8500 archs, use the PRCMU register interface, for the older + * Nomadik, provide some stubs. The functions using these will only be + * called on the U8500 series. + */ +#ifdef CONFIG_ARCH_U8500 #include <linux/mfd/dbx500-prcmu.h> +#else +static inline u32 prcmu_read(unsigned int reg) { + return 0; +} +static inline void prcmu_write(unsigned int reg, u32 value) {} +static inline void prcmu_write_masked(unsigned int reg, u32 mask, u32 value) {} +#endif #include <asm/mach/irq.h> @@ -1268,6 +1281,7 @@ static int __devinit nmk_gpio_probe(struct platform_device *dev) struct clk *clk; int secondary_irq; void __iomem *base; + int irq_start = -1; int irq; int ret; @@ -1371,19 +1385,11 @@ static int __devinit nmk_gpio_probe(struct platform_device *dev) platform_set_drvdata(dev, nmk_chip); - if (np) { - /* The DT case will just grab a set of IRQ numbers */ - nmk_chip->domain = irq_domain_add_linear(np, NMK_GPIO_PER_CHIP, - &nmk_gpio_irq_simple_ops, nmk_chip); - } else { - /* Non-DT legacy mode, use hardwired IRQ numbers */ - int irq_start; - + if (!np) irq_start = NOMADIK_GPIO_TO_IRQ(pdata->first_gpio); - nmk_chip->domain = irq_domain_add_simple(NULL, + nmk_chip->domain = irq_domain_add_simple(NULL, NMK_GPIO_PER_CHIP, irq_start, &nmk_gpio_irq_simple_ops, nmk_chip); - } if (!nmk_chip->domain) { dev_err(&dev->dev, "failed to create irqdomain\n"); ret = -ENOSYS; diff --git a/drivers/pinctrl/pinctrl-samsung.c b/drivers/pinctrl/pinctrl-samsung.c index dd108a9..861cd5f 100644 --- a/drivers/pinctrl/pinctrl-samsung.c +++ b/drivers/pinctrl/pinctrl-samsung.c @@ -513,7 +513,7 @@ static int samsung_gpio_direction_output(struct gpio_chip *gc, unsigned offset, * Parse the pin names listed in the 'samsung,pins' property and convert it * into a list of gpio numbers are create a pin group from it. */ -static int __init samsung_pinctrl_parse_dt_pins(struct platform_device *pdev, +static int __devinit samsung_pinctrl_parse_dt_pins(struct platform_device *pdev, struct device_node *cfg_np, struct pinctrl_desc *pctl, unsigned int **pin_list, unsigned int *npins) { @@ -560,7 +560,7 @@ static int __init samsung_pinctrl_parse_dt_pins(struct platform_device *pdev, * from device node of the pin-controller. A pin group is formed with all * the pins listed in the "samsung,pins" property. */ -static int __init samsung_pinctrl_parse_dt(struct platform_device *pdev, +static int __devinit samsung_pinctrl_parse_dt(struct platform_device *pdev, struct samsung_pinctrl_drv_data *drvdata) { struct device *dev = &pdev->dev; @@ -655,7 +655,7 @@ static int __init samsung_pinctrl_parse_dt(struct platform_device *pdev, } /* register the pinctrl interface with the pinctrl subsystem */ -static int __init samsung_pinctrl_register(struct platform_device *pdev, +static int __devinit samsung_pinctrl_register(struct platform_device *pdev, struct samsung_pinctrl_drv_data *drvdata) { struct pinctrl_desc *ctrldesc = &drvdata->pctl; @@ -729,7 +729,7 @@ static int __init samsung_pinctrl_register(struct platform_device *pdev, } /* register the gpiolib interface with the gpiolib subsystem */ -static int __init samsung_gpiolib_register(struct platform_device *pdev, +static int __devinit samsung_gpiolib_register(struct platform_device *pdev, struct samsung_pinctrl_drv_data *drvdata) { struct gpio_chip *gc; @@ -762,7 +762,7 @@ static int __init samsung_gpiolib_register(struct platform_device *pdev, } /* unregister the gpiolib interface with the gpiolib subsystem */ -static int __init samsung_gpiolib_unregister(struct platform_device *pdev, +static int __devinit samsung_gpiolib_unregister(struct platform_device *pdev, struct samsung_pinctrl_drv_data *drvdata) { int ret = gpiochip_remove(drvdata->gc); diff --git a/drivers/pinctrl/pinctrl-sirf.c b/drivers/pinctrl/pinctrl-sirf.c index 675497c..9ecacf3 100644 --- a/drivers/pinctrl/pinctrl-sirf.c +++ b/drivers/pinctrl/pinctrl-sirf.c @@ -1323,41 +1323,6 @@ static inline struct sirfsoc_gpio_bank *sirfsoc_gpio_to_bank(unsigned int gpio) return &sgpio_bank[gpio / SIRFSOC_GPIO_BANK_SIZE]; } -void sirfsoc_gpio_set_pull(unsigned gpio, unsigned mode) -{ - struct sirfsoc_gpio_bank *bank = sirfsoc_gpio_to_bank(gpio); - int idx = sirfsoc_gpio_to_offset(gpio); - u32 val, offset; - unsigned long flags; - - offset = SIRFSOC_GPIO_CTRL(bank->id, idx); - - spin_lock_irqsave(&sgpio_lock, flags); - - val = readl(bank->chip.regs + offset); - - switch (mode) { - case SIRFSOC_GPIO_PULL_NONE: - val &= ~SIRFSOC_GPIO_CTL_PULL_MASK; - break; - case SIRFSOC_GPIO_PULL_UP: - val |= SIRFSOC_GPIO_CTL_PULL_MASK; - val |= SIRFSOC_GPIO_CTL_PULL_HIGH; - break; - case SIRFSOC_GPIO_PULL_DOWN: - val |= SIRFSOC_GPIO_CTL_PULL_MASK; - val &= ~SIRFSOC_GPIO_CTL_PULL_HIGH; - break; - default: - break; - } - - writel(val, bank->chip.regs + offset); - - spin_unlock_irqrestore(&sgpio_lock, flags); -} -EXPORT_SYMBOL(sirfsoc_gpio_set_pull); - static inline struct sirfsoc_gpio_bank *sirfsoc_irqchip_to_bank(struct gpio_chip *chip) { return container_of(to_of_mm_gpio_chip(chip), struct sirfsoc_gpio_bank, chip); diff --git a/drivers/pinctrl/pinctrl-xway.c b/drivers/pinctrl/pinctrl-xway.c index f8d917d..b9bcaec 100644 --- a/drivers/pinctrl/pinctrl-xway.c +++ b/drivers/pinctrl/pinctrl-xway.c @@ -17,8 +17,6 @@ #include <linux/ioport.h> #include <linux/io.h> #include <linux/device.h> -#include <linux/module.h> -#include <linux/io.h> #include <linux/platform_device.h> #include "pinctrl-lantiq.h" diff --git a/fs/proc/task_mmu.c b/fs/proc/task_mmu.c index 79827ce..14df880 100644 --- a/fs/proc/task_mmu.c +++ b/fs/proc/task_mmu.c @@ -1158,6 +1158,7 @@ static int show_numa_map(struct seq_file *m, void *v, int is_pid) struct vm_area_struct *vma = v; struct numa_maps *md = &numa_priv->md; struct file *file = vma->vm_file; + struct task_struct *task = proc_priv->task; struct mm_struct *mm = vma->vm_mm; struct mm_walk walk = {}; struct mempolicy *pol; @@ -1177,9 +1178,11 @@ static int show_numa_map(struct seq_file *m, void *v, int is_pid) walk.private = md; walk.mm = mm; - pol = get_vma_policy(proc_priv->task, vma, vma->vm_start); + task_lock(task); + pol = get_vma_policy(task, vma, vma->vm_start); mpol_to_str(buffer, sizeof(buffer), pol, 0); mpol_cond_put(pol); + task_unlock(task); seq_printf(m, "%08lx %s", vma->vm_start, buffer); @@ -1189,7 +1192,7 @@ static int show_numa_map(struct seq_file *m, void *v, int is_pid) } else if (vma->vm_start <= mm->brk && vma->vm_end >= mm->start_brk) { seq_printf(m, " heap"); } else { - pid_t tid = vm_is_stack(proc_priv->task, vma, is_pid); + pid_t tid = vm_is_stack(task, vma, is_pid); if (tid != 0) { /* * Thread stack in /proc/PID/task/TID/maps or diff --git a/mm/mempolicy.c b/mm/mempolicy.c index 0b78fb9..d04a8a5 100644 --- a/mm/mempolicy.c +++ b/mm/mempolicy.c @@ -1536,9 +1536,8 @@ asmlinkage long compat_sys_mbind(compat_ulong_t start, compat_ulong_t len, * * Returns effective policy for a VMA at specified address. * Falls back to @task or system default policy, as necessary. - * Current or other task's task mempolicy and non-shared vma policies - * are protected by the task's mmap_sem, which must be held for read by - * the caller. + * Current or other task's task mempolicy and non-shared vma policies must be + * protected by task_lock(task) by the caller. * Shared policies [those marked as MPOL_F_SHARED] require an extra reference * count--added by the get_policy() vm_op, as appropriate--to protect against * freeing by another task. It is the caller's responsibility to free the |