diff options
Diffstat (limited to 'Documentation/devicetree')
15 files changed, 266 insertions, 205 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt index 723c205..d106146 100644 --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt +++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt @@ -7,7 +7,6 @@ Required properties: - interrupts: Should contain the IRQ line for the ADC - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this device - - atmel,adc-num-channels: Number of channels available in the ADC - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - atmel,adc-vref: Reference voltage in millivolts for the conversions @@ -24,6 +23,13 @@ Optional properties: resolution will be used. - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds + - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this + value is set, then adc driver will enable touch screen + support. + NOTE: when adc touch screen enabled, the adc hardware trigger will be + disabled. Since touch screen will occupied the trigger register. + - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It + make touch detect more precision. Optional trigger Nodes: - Required properties: diff --git a/Documentation/devicetree/bindings/iio/light/cm36651.txt b/Documentation/devicetree/bindings/iio/light/cm36651.txt new file mode 100644 index 0000000..c03e19d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/cm36651.txt @@ -0,0 +1,26 @@ +* Capella CM36651 I2C Proximity and Color Light sensor + +Required properties: +- compatible: must be "capella,cm36651" +- reg: the I2C address of the device +- interrupts: interrupt-specifier for the sole interrupt + generated by the device +- vled-supply: regulator for the IR LED. IR_LED is a part + of the cm36651 for proximity detection. + As covered in ../../regulator/regulator.txt + +Example: + + i2c_cm36651: i2c-gpio { + /* ... */ + + cm36651@18 { + compatible = "capella,cm36651"; + reg = <0x18>; + interrupt-parent = <&gpx0>; + interrupts = <2 0>; + vled-supply = <&ps_als_reg>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt new file mode 100644 index 0000000..9231c82 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt @@ -0,0 +1,21 @@ +* Sharp GP2AP020A00F I2C Proximity/ALS sensor + +The proximity detector sensor requires power supply +for its built-in led. It is also defined by this binding. + +Required properties: + + - compatible : should be "sharp,gp2ap020a00f" + - reg : the I2C slave address of the light sensor + - interrupts : interrupt specifier for the sole interrupt generated + by the device + - vled-supply : VLED power supply, as covered in ../regulator/regulator.txt + +Example: + +gp2ap020a00f@39 { + compatible = "sharp,gp2ap020a00f"; + reg = <0x39>; + interrupts = <2 0>; + vled-supply = <...>; +}; diff --git a/Documentation/devicetree/bindings/memory.txt b/Documentation/devicetree/bindings/memory.txt deleted file mode 100644 index eb24693..0000000 --- a/Documentation/devicetree/bindings/memory.txt +++ /dev/null @@ -1,168 +0,0 @@ -*** Memory binding *** - -The /memory node provides basic information about the address and size -of the physical memory. This node is usually filled or updated by the -bootloader, depending on the actual memory configuration of the given -hardware. - -The memory layout is described by the following node: - -/ { - #address-cells = <(n)>; - #size-cells = <(m)>; - memory { - device_type = "memory"; - reg = <(baseaddr1) (size1) - (baseaddr2) (size2) - ... - (baseaddrN) (sizeN)>; - }; - ... -}; - -A memory node follows the typical device tree rules for "reg" property: -n: number of cells used to store base address value -m: number of cells used to store size value -baseaddrX: defines a base address of the defined memory bank -sizeX: the size of the defined memory bank - - -More than one memory bank can be defined. - - -*** Reserved memory regions *** - -In /memory/reserved-memory node one can create child nodes describing -particular reserved (excluded from normal use) memory regions. Such -memory regions are usually designed for the special usage by various -device drivers. A good example are contiguous memory allocations or -memory sharing with other operating system on the same hardware board. -Those special memory regions might depend on the board configuration and -devices used on the target system. - -Parameters for each memory region can be encoded into the device tree -with the following convention: - -[(label):] (name) { - compatible = "linux,contiguous-memory-region", "reserved-memory-region"; - reg = <(address) (size)>; - (linux,default-contiguous-region); -}; - -compatible: one or more of: - - "linux,contiguous-memory-region" - enables binding of this - region to Contiguous Memory Allocator (special region for - contiguous memory allocations, shared with movable system - memory, Linux kernel-specific). - - "reserved-memory-region" - compatibility is defined, given - region is assigned for exclusive usage for by the respective - devices. - -reg: standard property defining the base address and size of - the memory region - -linux,default-contiguous-region: property indicating that the region - is the default region for all contiguous memory - allocations, Linux specific (optional) - -It is optional to specify the base address, so if one wants to use -autoconfiguration of the base address, '0' can be specified as a base -address in the 'reg' property. - -The /memory/reserved-memory node must contain the same #address-cells -and #size-cells value as the root node. - - -*** Device node's properties *** - -Once regions in the /memory/reserved-memory node have been defined, they -may be referenced by other device nodes. Bindings that wish to reference -memory regions should explicitly document their use of the following -property: - -memory-region = <&phandle_to_defined_region>; - -This property indicates that the device driver should use the memory -region pointed by the given phandle. - - -*** Example *** - -This example defines a memory consisting of 4 memory banks. 3 contiguous -regions are defined for Linux kernel, one default of all device drivers -(named contig_mem, placed at 0x72000000, 64MiB), one dedicated to the -framebuffer device (labelled display_mem, placed at 0x78000000, 8MiB) -and one for multimedia processing (labelled multimedia_mem, placed at -0x77000000, 64MiB). 'display_mem' region is then assigned to fb@12300000 -device for DMA memory allocations (Linux kernel drivers will use CMA is -available or dma-exclusive usage otherwise). 'multimedia_mem' is -assigned to scaler@12500000 and codec@12600000 devices for contiguous -memory allocations when CMA driver is enabled. - -The reason for creating a separate region for framebuffer device is to -match the framebuffer base address to the one configured by bootloader, -so once Linux kernel drivers starts no glitches on the displayed boot -logo appears. Scaller and codec drivers should share the memory -allocations. - -/ { - #address-cells = <1>; - #size-cells = <1>; - - /* ... */ - - memory { - reg = <0x40000000 0x10000000 - 0x50000000 0x10000000 - 0x60000000 0x10000000 - 0x70000000 0x10000000>; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - - /* - * global autoconfigured region for contiguous allocations - * (used only with Contiguous Memory Allocator) - */ - contig_region@0 { - compatible = "linux,contiguous-memory-region"; - reg = <0x0 0x4000000>; - linux,default-contiguous-region; - }; - - /* - * special region for framebuffer - */ - display_region: region@78000000 { - compatible = "linux,contiguous-memory-region", "reserved-memory-region"; - reg = <0x78000000 0x800000>; - }; - - /* - * special region for multimedia processing devices - */ - multimedia_region: region@77000000 { - compatible = "linux,contiguous-memory-region"; - reg = <0x77000000 0x4000000>; - }; - }; - }; - - /* ... */ - - fb0: fb@12300000 { - status = "okay"; - memory-region = <&display_region>; - }; - - scaler: scaler@12500000 { - status = "okay"; - memory-region = <&multimedia_region>; - }; - - codec: codec@12600000 { - status = "okay"; - memory-region = <&multimedia_region>; - }; -}; diff --git a/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt new file mode 100644 index 0000000..68ba372 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt @@ -0,0 +1,17 @@ +Allwinner sunxi-sid + +Required properties: +- compatible: "allwinner,sun4i-sid" or "allwinner,sun7i-a20-sid". +- reg: Should contain registers location and length + +Example for sun4i: + sid@01c23800 { + compatible = "allwinner,sun4i-sid"; + reg = <0x01c23800 0x10> + }; + +Example for sun7i: + sid@01c23800 { + compatible = "allwinner,sun7i-a20-sid"; + reg = <0x01c23800 0x200> + }; diff --git a/Documentation/devicetree/bindings/misc/ti,dac7512.txt b/Documentation/devicetree/bindings/misc/ti,dac7512.txt new file mode 100644 index 0000000..1db4593 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ti,dac7512.txt @@ -0,0 +1,20 @@ +TI DAC7512 DEVICETREE BINDINGS + +Required properties: + + - "compatible" Must be set to "ti,dac7512" + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + + +Example: + + spi_master { + dac7512: dac7512@0 { + compatible = "ti,dac7512"; + reg = <0>; /* CS0 */ + spi-max-frequency = <1000000>; + }; + }; + diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt new file mode 100644 index 0000000..8ae844f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -0,0 +1,66 @@ +This document explains only the device tree data binding. For general +information about PHY subsystem refer to Documentation/phy.txt + +PHY device node +=============== + +Required Properties: +#phy-cells: Number of cells in a PHY specifier; The meaning of all those + cells is defined by the binding for the phy node. The PHY + provider can use the values in cells to find the appropriate + PHY. + +For example: + +phys: phy { + compatible = "xxx"; + reg = <...>; + . + . + #phy-cells = <1>; + . + . +}; + +That node describes an IP block (PHY provider) that implements 2 different PHYs. +In order to differentiate between these 2 PHYs, an additonal specifier should be +given while trying to get a reference to it. + +PHY user node +============= + +Required Properties: +phys : the phandle for the PHY device (used by the PHY subsystem) +phy-names : the names of the PHY corresponding to the PHYs present in the + *phys* phandle + +Example 1: +usb1: usb_otg_ss@xxx { + compatible = "xxx"; + reg = <xxx>; + . + . + phys = <&usb2_phy>, <&usb3_phy>; + phy-names = "usb2phy", "usb3phy"; + . + . +}; + +This node represents a controller that uses two PHYs, one for usb2 and one for +usb3. + +Example 2: +usb2: usb_otg_ss@xxx { + compatible = "xxx"; + reg = <xxx>; + . + . + phys = <&phys 1>; + phy-names = "usbphy"; + . + . +}; + +This node represents a controller that uses one of the PHYs of the PHY provider +device defined previously. Note that the phy handle has an additional specifier +"1" to differentiate between the two PHYs. diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt new file mode 100644 index 0000000..c0fccaa --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -0,0 +1,22 @@ +Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY +------------------------------------------------- + +Required properties: +- compatible : should be "samsung,s5pv210-mipi-video-phy"; +- reg : offset and length of the MIPI DPHY register set; +- #phy-cells : from the generic phy bindings, must be 1; + +For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in +the PHY specifier identifies the PHY and its meaning is as follows: + 0 - MIPI CSIS 0, + 1 - MIPI DSIM 0, + 2 - MIPI CSIS 1, + 3 - MIPI DSIM 1. + +Samsung EXYNOS SoC series Display Port PHY +------------------------------------------------- + +Required properties: +- compatible : should be "samsung,exynos5250-dp-video-phy"; +- reg : offset and length of the Display Port PHY register set; +- #phy-cells : from the generic PHY bindings, must be 0; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt index 4688205..ee05dc3 100644 --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt @@ -1,7 +1,8 @@ * Freescale i.MX28 LRADC device driver Required properties: -- compatible: Should be "fsl,imx28-lradc" +- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc" + for i.MX28 SoC - reg: Address and length of the register set for the device - interrupts: Should contain the LRADC interrupts @@ -9,13 +10,38 @@ Optional properties: - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen to LRADC. Valid value is either 4 or 5. If this property is not present, then the touchscreen is - disabled. + disabled. 5 wires is valid for i.MX28 SoC only. +- fsl,ave-ctrl: number of samples per direction to calculate an average value. + Allowed value is 1 ... 31, default is 4 +- fsl,ave-delay: delay between consecutive samples. Allowed value is + 1 ... 2047. It is used if 'fsl,ave-ctrl' > 1, counts at + 2 kHz and its default is 2 (= 1 ms) +- fsl,settling: delay between plate switch to next sample. Allowed value is + 1 ... 2047. It counts at 2 kHz and its default is + 10 (= 5 ms) -Examples: +Example for i.MX23 SoC: + + lradc@80050000 { + compatible = "fsl,imx23-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <36 37 38 39 40 41 42 43 44>; + status = "okay"; + fsl,lradc-touchscreen-wires = <4>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; + +Example for i.MX28 SoC: lradc@80050000 { compatible = "fsl,imx28-lradc"; reg = <0x80050000 0x2000>; - interrupts = <10 14 15 16 17 18 19 - 20 21 22 23 24 25>; + interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; + status = "okay"; + fsl,lradc-touchscreen-wires = <5>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; }; diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt new file mode 100644 index 0000000..5ea26c6 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -0,0 +1,17 @@ +MSM SoC HSUSB controllers + +EHCI + +Required properties: +- compatible: Should contain "qcom,ehci-host" +- regs: offset and length of the register set in the memory map +- usb-phy: phandle for the PHY device + +Example EHCI controller device node: + + ehci: ehci@f9a55000 { + compatible = "qcom,ehci-host"; + reg = <0xf9a55000 0x400>; + usb-phy = <&usb_otg>; + }; + diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 9088ab0..090e5e2 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -3,9 +3,6 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" - ti,hwmods : must be "usb_otg_hs" - - ti,has-mailbox : to specify that omap uses an external mailbox - (in control module) to communicate with the musb core during device connect - and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - num-eps : Specifies the number of endpoints. This is also a @@ -19,6 +16,9 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply up to 100mA when operating in host mode. - usb-phy : the phandle for the PHY device + - phys : the phandle for the PHY device (used by generic PHY framework) + - phy-names : the names of the PHY corresponding to the PHYs present in the + *phy* phandle. Optional properties: - ctrl-module : phandle of the control module this glue uses to write to @@ -28,11 +28,12 @@ SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; ti,hwmods = "usb_otg_hs"; - ti,has-mailbox; multipoint = <1>; num-eps = <16>; ram-bits = <12>; ctrl-module = <&omap_control_usb>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; }; Board specific device node entry @@ -78,22 +79,22 @@ omap_dwc3 { OMAP CONTROL USB Required properties: - - compatible: Should be "ti,omap-control-usb" + - compatible: Should be one of + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register + e.g. USB2_PHY on OMAP5. + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control + e.g. USB3 PHY and SATA PHY on OMAP5. + "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on + DRA7 platform. - reg : Address and length of the register set for the device. It contains - the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" - depending upon omap4 or omap5. - - reg-names: The names of the register addresses corresponding to the registers - filled in "reg". - - ti,type: This is used to differentiate whether the control module has - usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to - notify events to the musb core and omap5 has usb3 phy power register to - power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 - phy power. + the address of "otghs_control" for control-phy-otghs or "power" register + for other types. + - reg-names: should be "otghs_control" control-phy-otghs and "power" for + other types. omap_control_usb: omap-control-usb@4a002300 { - compatible = "ti,omap-control-usb"; - reg = <0x4a002300 0x4>, - <0x4a00233c 0x4>; - reg-names = "control_dev_conf", "otghs_control"; - ti,type = <1>; + compatible = "ti,control-phy-otghs"; + reg = <0x4a00233c 0x4>; + reg-names = "otghs_control"; }; diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt index d7e2726..1bd37fa 100644 --- a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt +++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt @@ -15,7 +15,7 @@ Optional properties: - vcc-supply: phandle to the regulator that provides RESET to the PHY. -- reset-supply: phandle to the regulator that provides power to the PHY. +- reset-gpios: Should specify the GPIO for reset. Example: @@ -25,10 +25,9 @@ Example: clocks = <&osc 0>; clock-names = "main_clk"; vcc-supply = <&hsusb1_vcc_regulator>; - reset-supply = <&hsusb1_reset_regulator>; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; }; hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator and expects that clock to be configured to 19.2MHz by the NOP PHY driver. -hsusb1_vcc_regulator provides power to the PHY and hsusb1_reset_regulator -controls RESET. +hsusb1_vcc_regulator provides power to the PHY and GPIO 7 controls RESET. diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt index 61496f5..c0245c8 100644 --- a/Documentation/devicetree/bindings/usb/usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -5,6 +5,8 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" - reg : Address and length of the register set for the device. + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. Optional properties: - ctrl-module : phandle of the control module used by PHY driver to power on @@ -16,6 +18,7 @@ usb2phy@4a0ad080 { compatible = "ti,omap-usb2"; reg = <0x4a0ad080 0x58>; ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; }; OMAP USB3 PHY @@ -25,6 +28,8 @@ Required properties: - reg : Address and length of the register set for the device. - reg-names: The names of the register addresses corresponding to the registers filled in "reg". + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. Optional properties: - ctrl-module : phandle of the control module used by PHY driver to power on @@ -39,4 +44,5 @@ usb3phy@4a084400 { <0x4a084c00 0x40>; reg-names = "phy_rx", "phy_tx", "pll_ctrl"; ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2956800..04eab45 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -15,6 +15,7 @@ atmel Atmel Corporation avago Avago Technologies bosch Bosch Sensortec GmbH brcm Broadcom Corporation +capella Capella Microsystems, Inc cavium Cavium, Inc. chrp Common Hardware Reference Platform cirrus Cirrus Logic, Inc. diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt index 84f10c1..3289d76 100644 --- a/Documentation/devicetree/bindings/video/exynos_dp.txt +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -6,10 +6,10 @@ We use two nodes: -dptx-phy node(defined inside dp-controller node) For the DP-PHY initialization, we use the dptx-phy node. -Required properties for dptx-phy: - -reg: +Required properties for dptx-phy: deprecated, use phys and phy-names + -reg: deprecated Base address of DP PHY register. - -samsung,enable-mask: + -samsung,enable-mask: deprecated The bit-mask used to enable/disable DP PHY. For the Panel initialization, we read data from dp-controller node. @@ -27,6 +27,10 @@ Required properties for dp-controller: from common clock binding: Shall be "dp". -interrupt-parent: phandle to Interrupt combiner node. + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". -samsung,color-space: input video data format. COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 @@ -68,11 +72,8 @@ SOC specific portion: clocks = <&clock 342>; clock-names = "dp"; - dptx-phy { - reg = <0x10040720>; - samsung,enable-mask = <1>; - }; - + phys = <&dp_phy>; + phy-names = "dp"; }; Board Specific portion: |