diff options
Diffstat (limited to 'Documentation/devicetree')
32 files changed, 734 insertions, 37 deletions
diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt index e5f1301..fff10da 100644 --- a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt +++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt @@ -10,6 +10,14 @@ Recommended properties: services interrupts for this device. - ti,hwmods: Name of the hwmod associated to the LCDC +Optional properties: + - max-bandwidth: The maximum pixels per second that the memory + interface / lcd controller combination can sustain + - max-width: The maximum horizontal pixel width supported by + the lcd controller. + - max-pixelclock: The maximum pixel clock that can be supported + by the lcd controller in KHz. + Example: fb: fb@4830e000 { diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt new file mode 100644 index 0000000..491c97b --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -0,0 +1,44 @@ +* TI - TSC ADC (Touschscreen and analog digital converter) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: +- child "tsc" + ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen + support on the platform. + ti,x-plate-resistance: X plate resistance + ti,coordiante-readouts: The sequencer supports a total of 16 + programmable steps each step is used to + read a single coordinate. A single + readout is enough but multiple reads can + increase the quality. + A value of 5 means, 5 reads for X, 5 for + Y and 2 for Z (always). This utilises 12 + of the 16 software steps available. The + remaining 4 can be used by the ADC. + ti,wire-config: Different boards could have a different order for + connecting wires on touchscreen. We need to provide an + 8 bit number where in the 1st four bits represent the + analog lines and the next 4 bits represent positive/ + negative terminal on that input line. Notations to + represent the input lines and terminals resoectively + is as follows: + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + XP = 0, XN = 1, YP = 2, YN = 3. +- child "adc" + ti,adc-channels: List of analog inputs available for ADC. + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + +Example: + tscadc: tscadc@44e0d000 { + compatible = "ti,am3359-tscadc"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordiante-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; + } diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt new file mode 100644 index 0000000..e34c6cd --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -0,0 +1,70 @@ +* ARM System MMU Architecture Implementation + +ARM SoCs may contain an implementation of the ARM System Memory +Management Unit Architecture, which can be used to provide 1 or 2 stages +of address translation to bus masters external to the CPU. + +The SMMU may also raise interrupts in response to various fault +conditions. + +** System MMU required properties: + +- compatible : Should be one of: + + "arm,smmu-v1" + "arm,smmu-v2" + "arm,mmu-400" + "arm,mmu-500" + + depending on the particular implementation and/or the + version of the architecture implemented. + +- reg : Base address and size of the SMMU. + +- #global-interrupts : The number of global interrupts exposed by the + device. + +- interrupts : Interrupt list, with the first #global-irqs entries + corresponding to the global interrupts and any + following entries corresponding to context interrupts, + specified in order of their indexing by the SMMU. + + For SMMUv2 implementations, there must be exactly one + interrupt per context bank. In the case of a single, + combined interrupt, it must be listed multiple times. + +- mmu-masters : A list of phandles to device nodes representing bus + masters for which the SMMU can provide a translation + and their corresponding StreamIDs (see example below). + Each device node linked from this list must have a + "#stream-id-cells" property, indicating the number of + StreamIDs associated with it. + +** System MMU optional properties: + +- smmu-parent : When multiple SMMUs are chained together, this + property can be used to provide a phandle to the + parent SMMU (that is the next SMMU on the path going + from the mmu-masters towards memory) node for this + SMMU. + +Example: + + smmu { + compatible = "arm,smmu-v1"; + reg = <0xba5e0000 0x10000>; + #global-interrupts = <2>; + interrupts = <0 32 4>, + <0 33 4>, + <0 34 4>, /* This is the first context interrupt */ + <0 35 4>, + <0 36 4>, + <0 37 4>; + + /* + * Two DMA controllers, the first with two StreamIDs (0xd01d + * and 0xd01e) and the second with only one (0xd11c). + */ + mmu-masters = <&dma0 0xd01d 0xd01e>, + <&dma1 0xd11c>; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt new file mode 100644 index 0000000..23a3650 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8998.txt @@ -0,0 +1,119 @@ +* Maxim MAX8998, National/TI LP3974 multi-function device + +The Maxim MAX8998 is a multi-function device which includes voltage/current +regulators, real time clock, battery charging controller and several +other sub-blocks. It is interfaced using an I2C interface. Each sub-block +is addressed by the host system using different i2c slave address. + +PMIC sub-block +-------------- + +The PMIC sub-block contains a number of voltage and current regulators, +with controllable parameters and dynamic voltage scaling capability. +In addition, it includes a real time clock and battery charging controller +as well. It is accessible at I2C address 0x66. + +Required properties: +- compatible: Should be one of the following: + - "maxim,max8998" for Maxim MAX8998 + - "national,lp3974" or "ti,lp3974" for National/TI LP3974. +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from MAX8998 are routed to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for main interrupt. + - Second interrupt specifier is for power-on/-off interrupt. +- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used + for buck 1 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used + for buck 2 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from + the possible 4 options selectable by the dvs gpios. The value of this + property should be 0, 1, 2 or 3. If not specified or out of range, + a default value of 0 is taken. +- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from + the possible 2 options selectable by the dvs gpios. The value of this + property should be 0 or 1. If not specified or out of range, a default + value of 0 is taken. +- max8998,pmic-buck-voltage-lock: If present, disallows changing of + preprogrammed buck dvfs voltages. + +Additional properties required if max8998,pmic-buck1-dvs-gpios is defined: +- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts + for buck1 regulator that can be selected using dvs gpio. + +Additional properties required if max8998,pmic-buck2-dvs-gpio is defined: +- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts + for buck2 regulator that can be selected using dvs gpio. + +Regulators: All the regulators of MAX8998 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the MAX8998 PMIC block are supported. Note that +the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK +number as described in MAX8998 datasheet. + + - LDOn + - valid values for n are 2 to 17 + - Example: LDO2, LDO10, LDO17 + - BUCKn + - valid values for n are 1 to 4. + - Example: BUCK1, BUCK2, BUCK3, BUCK4 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details. + +Example: + + pmic@66 { + compatible = "maxim,max8998-pmic"; + reg = <0x66>; + interrupt-parent = <&wakeup_eint>; + interrupts = <4 0>, <3 0>; + + /* Buck 1 DVS settings */ + max8998,pmic-buck1-default-dvs-idx = <0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>; /* SET2 */ + max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1000000>, <950000>; + + /* Buck 2 DVS settings */ + max8998,pmic-buck2-default-dvs-idx = <0>; + max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */ + max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>; + + /* Regulators to instantiate */ + regulators { + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt new file mode 100644 index 0000000..8e15ec3 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -0,0 +1,28 @@ +Texas Instruments TWL family (twl4030) reset and power management module + +The power management module inside the TWL family provides several facilities +to control the power resources, including power scripts. For now, the +binding only supports the complete shutdown of the system after poweroff. + +Required properties: +- compatible : must be "ti,twl4030-power" + +Optional properties: +- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or + SLEEP-to-OFF transition when the system poweroffs. + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_power: power { + compatible = "ti,twl4030-power"; + ti,use_poweroff; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 85aada2..458b57f 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -28,6 +28,7 @@ Optional properties: - cap-mmc-highspeed: MMC high-speed timing is supported - cap-power-off-card: powering off the card is safe - cap-sdio-irq: enable SDIO IRQ signalling on this interface +- full-pwr-cycle: full power cycle of the card is supported *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt new file mode 100644 index 0000000..8a3d91d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -0,0 +1,23 @@ +* Rockchip specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsis dw mshc controller properties described +by synopsis-dw-mshc.txt and the properties used by the Rockchip specific +extensions to the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following + +Example: + + rkdwmmc0@12200000 { + compatible = "rockchip,rk2928-dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 1180d78..cdcebea 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt @@ -39,6 +39,19 @@ Required Properties: Optional properties: +* clocks: from common clock binding: handle to biu and ciu clocks for the + bus interface unit clock and the card interface unit clock. + +* clock-names: from common clock binding: Shall be "biu" and "ciu". + If the biu clock is missing we'll simply skip enabling it. If the + ciu clock is missing we'll just assume that the clock is running at + clock-frequency. It is an error to omit both the ciu clock and the + clock-frequency. + +* clock-frequency: should be the frequency (in Hz) of the ciu clock. If this + is specified and the ciu clock is specified then we'll try to set the ciu + clock to this at probe time. + * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the value specified by num-slots. If this property is not specified, the value @@ -55,6 +68,9 @@ Optional properties: * broken-cd: as documented in mmc core bindings. +* vmmc-supply: The phandle to the regulator to use for vmmc. If this is + specified we'll defer probe until we can find this regulator. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using @@ -67,6 +83,8 @@ board specific portions as listed below. dwmmc0@12200000 { compatible = "snps,dw-mshc"; + clocks = <&clock 351>, <&clock 132>; + clock-names = "biu", "ciu"; reg = <0x12200000 0x1000>; interrupts = <0 75 0>; #address-cells = <1>; @@ -74,11 +92,13 @@ board specific portions as listed below. }; dwmmc0@12200000 { + clock-frequency = <400000000>; num-slots = <1>; supports-highspeed; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; + vmmc-supply = <&buck8>; slot@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt new file mode 100644 index 0000000..b90bfcd --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -0,0 +1,22 @@ +* Allwinner EMAC ethernet controller + +Required properties: +- compatible: should be "allwinner,sun4i-emac". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: A phandle to a phy node defining the PHY address (as the reg + property, a single integer). +- clocks: A phandle to the reference clock for this device + +Optional properties: +- (local-)mac-address: mac address to be used by this driver + +Example: + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun4i-emac"; + reg = <0x01c0b000 0x1000>; + interrupts = <55>; + clocks = <&ahb_gates 17>; + phy = <&phy0>; +}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt new file mode 100644 index 0000000..00b9f9a --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -0,0 +1,26 @@ +* Allwinner A10 MDIO Ethernet Controller interface + +Required properties: +- compatible: should be "allwinner,sun4i-mdio". +- reg: address and length of the register set for the device. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Example at the SoC level: +mdio@01c0b080 { + compatible = "allwinner,sun4i-mdio"; + reg = <0x01c0b080 0x14>; + #address-cells = <1>; + #size-cells = <0>; +}; + +And at the board level: + +mdio@01c0b080 { + phy-supply = <®_emac_3v3>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt new file mode 100644 index 0000000..bcbc3f0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/arc_emac.txt @@ -0,0 +1,38 @@ +* Synopsys ARC EMAC 10/100 Ethernet driver (EMAC) + +Required properties: +- compatible: Should be "snps,arc-emac" +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- clock-frequency: CPU frequency. It is needed to calculate and set polling +period of EMAC. +- max-speed: Maximum supported data-rate in Mbit/s. In some HW configurations +bandwidth of external memory controller might be a limiting factor. That's why +it's required to specify which data-rate is supported on current SoC or FPGA. +For example if only 10 Mbit/s is supported (10BASE-T) set "10". If 100 Mbit/s is +supported (100BASE-TX) set "100". +- phy: PHY device attached to the EMAC via MDIO bus + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Optional properties: +- mac-address: 6 bytes, mac address + +Examples: + + ethernet@c0fc2000 { + compatible = "snps,arc-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + clock-frequency = <80000000>; + max-speed = <100>; + phy = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index 8ff324e..56d6cc3 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -16,6 +16,8 @@ Optional properties: - clock-frequency : The oscillator frequency driving the flexcan device +- xceiver-supply: Regulator that powers the CAN transceiver + Example: can@1c000 { diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 4f2ca6b..05d660e 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -28,6 +28,8 @@ Optional properties: Slave Properties: Required properties: - phy_id : Specifies slave phy id +- phy-mode : The interface between the SoC and the PHY (a string + that of_get_phy_mode() can understand) - mac-address : Specifies slave MAC address Optional properties: @@ -58,11 +60,13 @@ Examples: cpts_clock_shift = <29>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; @@ -84,11 +88,13 @@ Examples: cpts_clock_shift = <29>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt new file mode 100644 index 0000000..2d39c99 --- /dev/null +++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt @@ -0,0 +1,26 @@ +Davicom DM9000 Fast Ethernet controller + +Required properties: +- compatible = "davicom,dm9000"; +- reg : physical addresses and sizes of registers, must contain 2 entries: + first entry : address register, + second entry : data register. +- interrupt-parent : interrupt controller to which the device is connected +- interrupts : interrupt specifier specific to interrupt controller + +Optional properties: +- local-mac-address : A bytestring of 6 bytes specifying Ethernet MAC address + to use (from firmware or bootloader) +- davicom,no-eeprom : Configuration EEPROM is not available +- davicom,ext-phy : Use external PHY + +Example: + + ethernet@18000000 { + compatible = "davicom,dm9000"; + reg = <0x18000000 0x2 0x18000004 0x2>; + interrupt-parent = <&gpn>; + interrupts = <7 4>; + local-mac-address = [00 00 de ad be ef]; + davicom,no-eeprom; + }; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt new file mode 100644 index 0000000..a73b79f --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -0,0 +1,85 @@ +Marvell Orion/Discovery ethernet controller +============================================= + +The Marvell Discovery ethernet controller can be found on Marvell Orion SoCs +(Kirkwood, Dove, Orion5x, and Discovery Innovation) and as part of Marvell +Discovery system controller chips (mv64[345]60). + +The Discovery ethernet controller is described with two levels of nodes. The +first level describes the ethernet controller itself and the second level +describes up to 3 ethernet port nodes within that controller. The reason for +the multiple levels is that the port registers are interleaved within a single +set of controller registers. Each port node describes port-specific properties. + +Note: The above separation is only true for Discovery system controllers. +For Orion SoCs we stick to the separation, although there each controller has +only one port associated. Multiple ports are implemented as multiple single-port +controllers. As Kirkwood has some issues with proper initialization after reset, +an extra compatible string is added for it. + +* Ethernet controller node + +Required controller properties: + - #address-cells: shall be 1. + - #size-cells: shall be 0. + - compatible: shall be one of "marvell,orion-eth", "marvell,kirkwood-eth". + - reg: address and length of the controller registers. + +Optional controller properties: + - clocks: phandle reference to the controller clock. + - marvell,tx-checksum-limit: max tx packet size for hardware checksum. + +* Ethernet port node + +Required port properties: + - device_type: shall be "network". + - compatible: shall be one of "marvell,orion-eth-port", + "marvell,kirkwood-eth-port". + - reg: port number relative to ethernet controller, shall be 0, 1, or 2. + - interrupts: port interrupt. + - local-mac-address: 6 bytes MAC address. + +Optional port properties: + - marvell,tx-queue-size: size of the transmit ring buffer. + - marvell,tx-sram-addr: address of transmit descriptor buffer located in SRAM. + - marvell,tx-sram-size: size of transmit descriptor buffer located in SRAM. + - marvell,rx-queue-size: size of the receive ring buffer. + - marvell,rx-sram-addr: address of receive descriptor buffer located in SRAM. + - marvell,rx-sram-size: size of receive descriptor buffer located in SRAM. + +and + + - phy-handle: phandle reference to ethernet PHY. + +or + + - speed: port speed if no PHY connected. + - duplex: port mode if no PHY connected. + +* Node example: + +mdio-bus { + ... + ethphy: ethernet-phy@8 { + device_type = "ethernet-phy"; + ... + }; +}; + +eth: ethernet-controller@72000 { + compatible = "marvell,orion-eth"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72000 0x2000>; + clocks = <&gate_clk 2>; + marvell,tx-checksum-limit = <1600>; + + ethernet@0 { + device_type = "network"; + compatible = "marvell,orion-eth-port"; + reg = <0>; + interrupts = <29>; + phy-handle = <ðphy>; + local-mac-address = [00 00 00 00 00 00]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt new file mode 100644 index 0000000..11ace3c --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt @@ -0,0 +1,9 @@ +Micrel KS8851 Ethernet mac + +Required properties: +- compatible = "micrel,ks8851-ml" of parallel interface +- reg : 2 physical address and size of registers for data and command +- interrupts : interrupt connection + +Optional properties: +- local-mac-address : Ethernet mac address to use diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 060bbf0..261c563 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -12,6 +12,16 @@ Required properties: property - phy-mode: String, operation mode of the PHY interface. Supported values are: "mii", "rmii", "gmii", "rgmii". +- snps,phy-addr phy address to connect to. +- snps,reset-gpio gpio number for phy reset. +- snps,reset-active-low boolean flag to indicate if phy reset is active low. +- snps,reset-delays-us is triplet of delays + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. +- snps,pbl Programmable Burst Length +- snps,fixed-burst Program the DMA to use the fixed burst mode +- snps,mixed-burst Program the DMA to use the mixed burst mode Optional properties: - mac-address: 6 bytes, mac address diff --git a/Documentation/devicetree/bindings/net/via-velocity.txt b/Documentation/devicetree/bindings/net/via-velocity.txt new file mode 100644 index 0000000..b3db469 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-velocity.txt @@ -0,0 +1,20 @@ +* VIA Velocity 10/100/1000 Network Controller + +Required properties: +- compatible : Should be "via,velocity-vt6110" +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Optional properties: +- no-eeprom : PCI network cards use an external EEPROM to store data. Embedded + devices quite often set this data in uboot and do not provide an eeprom. + Specify this option if you have no external eeprom. + +Examples: + +eth0@d8004000 { + compatible = "via,velocity-vt6110"; + reg = <0xd8004000 0x400>; + interrupts = <10>; + no-eeprom; +}; diff --git a/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt new file mode 100644 index 0000000..2246bc5 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt @@ -0,0 +1,44 @@ +Binding for TI/National Semiconductor LP8727 Charger + +Required properties: +- compatible: "ti,lp8727" +- reg: I2C slave address 27h + +Optional properties: +- interrupt-parent: interrupt controller node (see interrupt binding[0]) +- interrupts: interrupt specifier (see interrupt binding[0]) +- debounce-ms: interrupt debounce time. (u32) + +AC and USB charging parameters +- charger-type: "ac" or "usb" (string) +- eoc-level: value of 'enum lp8727_eoc_level' (u8) +- charging-current: value of 'enum lp8727_ichg' (u8) + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example) + +lp8727@27 { + compatible = "ti,lp8727"; + reg = <0x27>; + + /* GPIO 134 is used for LP8728 interrupt pin */ + interrupt-parent = <&gpio5>; /* base = 128 */ + interrupts = <6 0x2>; /* offset = 6, falling edge type */ + + debounce-ms = <300>; + + /* AC charger: 5% EOC and 500mA charging current */ + ac { + charger-type = "ac"; + eoc-level = /bits/ 8 <0>; + charging-current = /bits/ 8 <4>; + }; + + /* USB charger: 10% EOC and 400mA charging current */ + usb { + charger-type = "usb"; + eoc-level = /bits/ 8 <1>; + charging-current = /bits/ 8 <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt new file mode 100644 index 0000000..1e3dfe7 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt @@ -0,0 +1,27 @@ +NXP PCA9685 16-channel 12-bit PWM LED controller +================================================ + +Required properties: + - compatible: "nxp,pca9685-pwm" + - #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + The index 16 is the ALLCALL channel, that sets all PWM channels at the same + time. + +Optional properties: + - invert (bool): boolean to enable inverted logic + - open-drain (bool): boolean to configure outputs with open-drain structure; + if omitted use totem-pole structure + +Example: + +For LEDs that are directly connected to the PCA, the following setting is +applicable: + +pca: pca@41 { + compatible = "nxp,pca9685-pwm"; + #pwm-cells = <2>; + reg = <0x41>; + invert; + open-drain; +}; diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt index 9e5e51d..5c186a7 100644 --- a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -1,6 +1,6 @@ * Maxim MAX8997 Voltage and Current Regulator -The Maxim MAX8997 is a multi-function device which includes volatage and +The Maxim MAX8997 is a multi-function device which includes voltage and current regulators, rtc, charger controller and other sub-blocks. It is interfaced to the host controller using a i2c interface. Each sub-block is addressed by the host system using different i2c slave address. This document diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt index a35ff99..d1660a9 100644 --- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -1,6 +1,6 @@ * Samsung S5M8767 Voltage and Current Regulator -The Samsung S5M8767 is a multi-function device which includes volatage and +The Samsung S5M8767 is a multi-function device which includes voltage and current regulators, rtc, charger controller and other sub-blocks. It is interfaced to the host controller using a i2c interface. Each sub-block is addressed by the host system using different i2c slave address. This document @@ -103,13 +103,13 @@ Example: s5m8767,pmic-buck-default-dvs-idx = <0>; - s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ - <&gpx0 1 1 0 0>, /* DVS2 */ - <&gpx0 2 1 0 0>; /* DVS3 */ + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ + <&gpx0 1 0>, /* DVS2 */ + <&gpx0 2 0>; /* DVS3 */ - s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ - <&gpx2 4 1 0 0>, /* SET2 */ - <&gpx2 5 1 0 0>; /* SET3 */ + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ + <&gpx2 4 0>, /* SET2 */ + <&gpx2 5 0>; /* SET3 */ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, <1250000>, <1200000>, diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 658749b..75b0c16 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -18,20 +18,20 @@ For twl6030 regulators/LDOs - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS -For twl6025 regulators/LDOs +For twl6032 regulators/LDOs - compatible: - - "ti,twl6025-ldo1" for LDO1 LDO - - "ti,twl6025-ldo2" for LDO2 LDO - - "ti,twl6025-ldo3" for LDO3 LDO - - "ti,twl6025-ldo4" for LDO4 LDO - - "ti,twl6025-ldo5" for LDO5 LDO - - "ti,twl6025-ldo6" for LDO6 LDO - - "ti,twl6025-ldo7" for LDO7 LDO - - "ti,twl6025-ldoln" for LDOLN LDO - - "ti,twl6025-ldousb" for LDOUSB LDO - - "ti,twl6025-smps3" for SMPS3 SMPS - - "ti,twl6025-smps4" for SMPS4 SMPS - - "ti,twl6025-vio" for VIO SMPS + - "ti,twl6032-ldo1" for LDO1 LDO + - "ti,twl6032-ldo2" for LDO2 LDO + - "ti,twl6032-ldo3" for LDO3 LDO + - "ti,twl6032-ldo4" for LDO4 LDO + - "ti,twl6032-ldo5" for LDO5 LDO + - "ti,twl6032-ldo6" for LDO6 LDO + - "ti,twl6032-ldo7" for LDO7 LDO + - "ti,twl6032-ldoln" for LDOLN LDO + - "ti,twl6032-ldousb" for LDOUSB LDO + - "ti,twl6032-smps3" for SMPS3 SMPS + - "ti,twl6032-smps4" for SMPS4 SMPS + - "ti,twl6032-vio" for VIO SMPS For twl4030 regulators/LDOs - compatible: - "ti,twl4030-vaux1" for VAUX1 LDO diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt index 36b9aed..0aee0ad 100644 --- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -8,7 +8,7 @@ TWL6030 USB COMPARATOR usb interrupt number that raises VBUS interrupts when the controller has to act as device - usb-supply : phandle to the regulator device tree node. It should be vusb - if it is twl6030 or ldousb if it is twl6025 subclass. + if it is twl6030 or ldousb if it is twl6032 subclass. twl6030-usb { compatible = "ti,twl6030-usb"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 948f615..d5a79ca 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -18,6 +18,7 @@ chrp Common Hardware Reference Platform cirrus Cirrus Logic, Inc. cortina Cortina Systems, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) +davicom DAVICOM Semiconductor, Inc. denx Denx Software Engineering emmicro EM Microelectronic epson Seiko Epson Corp. diff --git a/Documentation/devicetree/bindings/video/display-timing.txt b/Documentation/devicetree/bindings/video/display-timing.txt index 1500385..e1d4a0b 100644 --- a/Documentation/devicetree/bindings/video/display-timing.txt +++ b/Documentation/devicetree/bindings/video/display-timing.txt @@ -34,6 +34,7 @@ optional properties: - ignored = ignored - interlaced (bool): boolean to enable interlaced mode - doublescan (bool): boolean to enable doublescan mode + - doubleclk (bool): boolean to enable doubleclock mode All the optional properties that are not bool follow the following logic: <1>: high active diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 589edee..323983b 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt @@ -1,22 +1,23 @@ Device-Tree bindings for drm hdmi driver Required properties: -- compatible: value should be "samsung,exynos5-hdmi". +- compatible: value should be one among the following: + 1) "samsung,exynos5-hdmi" <DEPRECATED> + 2) "samsung,exynos4210-hdmi" + 3) "samsung,exynos4212-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. - hpd-gpio: following information about the hotplug gpio pin. a) phandle of the gpio controller node. b) pin number within the gpio controller. - c) pin function mode. - d) optional flags and pull up/down. - e) drive strength. + c) optional flags and pull up/down. Example: hdmi { - compatible = "samsung,exynos5-hdmi"; + compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x100000>; interrupts = <0 95 0>; - hpd-gpio = <&gpx3 7 0xf 1 3>; + hpd-gpio = <&gpx3 7 1>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt index fa166d9..41eee97 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt @@ -1,12 +1,15 @@ Device-Tree bindings for hdmiddc driver Required properties: -- compatible: value should be "samsung,exynos5-hdmiddc". +- compatible: value should be one of the following + 1) "samsung,exynos5-hdmiddc" <DEPRECATED> + 2) "samsung,exynos4210-hdmiddc" + - reg: I2C address of the hdmiddc device. Example: hdmiddc { - compatible = "samsung,exynos5-hdmiddc"; + compatible = "samsung,exynos4210-hdmiddc"; reg = <0x50>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt index 858f4f9..162f641 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt @@ -1,12 +1,15 @@ Device-Tree bindings for hdmiphy driver Required properties: -- compatible: value should be "samsung,exynos5-hdmiphy". +- compatible: value should be one of the following: + 1) "samsung,exynos5-hdmiphy" <DEPRECATED> + 2) "samsung,exynos4210-hdmiphy". + 3) "samsung,exynos4212-hdmiphy". - reg: I2C address of the hdmiphy device. Example: hdmiphy { - compatible = "samsung,exynos5-hdmiphy"; + compatible = "samsung,exynos4210-hdmiphy"; reg = <0x38>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt index 9b2ea03..3334b0a 100644 --- a/Documentation/devicetree/bindings/video/exynos_mixer.txt +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt @@ -1,7 +1,12 @@ Device-Tree bindings for mixer driver Required properties: -- compatible: value should be "samsung,exynos5-mixer". +- compatible: value should be one of the following: + 1) "samsung,exynos5-mixer" <DEPRECATED> + 2) "samsung,exynos4210-mixer" + 3) "samsung,exynos5250-mixer" + 4) "samsung,exynos5420-mixer" + - reg: physical base address of the mixer and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -9,7 +14,7 @@ Required properties: Example: mixer { - compatible = "samsung,exynos5-mixer"; + compatible = "samsung,exynos5250-mixer"; reg = <0x14450000 0x10000>; interrupts = <0 94 0>; }; diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt new file mode 100644 index 0000000..46da08d --- /dev/null +++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt @@ -0,0 +1,51 @@ +Freescale imx21 Framebuffer + +This framebuffer driver supports devices imx1, imx21, imx25, and imx27. + +Required properties: +- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21 +- reg : Should contain 1 register ranges(address and length) +- interrupts : One interrupt of the fb dev + +Required nodes: +- display: Phandle to a display node as described in + Documentation/devicetree/bindings/video/display-timing.txt + Additional, the display node has to define properties: + - bits-per-pixel: Bits per pixel + - fsl,pcr: LCDC PCR value + +Optional properties: +- fsl,dmacr: DMA Control Register value. This is optional. By default, the + register is not modified as recommended by the datasheet. +- fsl,lscr1: LCDC Sharp Configuration Register value. + +Example: + + imxfb: fb@10021000 { + compatible = "fsl,imx21-fb"; + interrupts = <61>; + reg = <0x10021000 0x1000>; + display = <&display0>; + }; + + ... + + display0: display0 { + model = "Primeview-PD050VL1"; + native-mode = <&timing_disp0>; + bits-per-pixel = <16>; + fsl,pcr = <0xf0c88080>; /* non-standard but required */ + display-timings { + timing_disp0: 640x480 { + hactive = <640>; + vactive = <480>; + hback-porch = <112>; + hfront-porch = <36>; + hsync-len = <32>; + vback-porch = <33>; + vfront-porch = <33>; + vsync-len = <2>; + clock-frequency = <25000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt index 3d0060c..7a12542 100644 --- a/Documentation/devicetree/bindings/video/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -1,13 +1,17 @@ * Solomon SSD1307 Framebuffer Driver Required properties: - - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for - now is i2c. + - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for + now is i2c, and the supported chips are ssd1306 and ssd1307. - reg: Should contain address of the controller on the I2C bus. Most likely 0x3c or 0x3d - pwm: Should contain the pwm to use according to the OF device tree PWM - specification [0] + specification [0]. Only required for the ssd1307. - reset-gpios: Should contain the GPIO used to reset the OLED display + - solomon,height: Height in pixel of the screen driven by the controller + - solomon,width: Width in pixel of the screen driven by the controller + - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is + mapped to. Optional properties: - reset-active-low: Is the reset gpio is active on physical low? |