diff options
Diffstat (limited to 'Documentation/sysctl/net.txt')
-rw-r--r-- | Documentation/sysctl/net.txt | 49 |
1 files changed, 43 insertions, 6 deletions
diff --git a/Documentation/sysctl/net.txt b/Documentation/sysctl/net.txt index 98335b7..d69e14c 100644 --- a/Documentation/sysctl/net.txt +++ b/Documentation/sysctl/net.txt @@ -1,4 +1,4 @@ -Documentation for /proc/sys/net/* kernel version 2.4.0-test11-pre4 +Documentation for /proc/sys/net/* (c) 1999 Terrehon Bowden <terrehon@pacbell.net> Bodo Bauer <bb@ricochet.net> (c) 2000 Jorge Nerin <comandante@zaralinux.com> @@ -9,10 +9,10 @@ For general info and legal blurb, please look in README. ============================================================== This file contains the documentation for the sysctl files in -/proc/sys/net and is valid for Linux kernel version 2.4.0-test11-pre4. +/proc/sys/net The interface to the networking parts of the kernel is located in -/proc/sys/net. The following table shows all possible subdirectories.You may +/proc/sys/net. The following table shows all possible subdirectories. You may see only some of them, depending on your kernel's configuration. @@ -26,7 +26,7 @@ Table : Subdirectories in /proc/sys/net ipv4 IP version 4 x25 X.25 protocol ipx IPX token-ring IBM token ring bridge Bridging decnet DEC net - ipv6 IP version 6 + ipv6 IP version 6 tipc TIPC .............................................................................. 1. /proc/sys/net/core - Network core options @@ -50,6 +50,29 @@ The maximum number of packets that kernel can handle on a NAPI interrupt, it's a Per-CPU variable. Default: 64 +low_latency_read +---------------- +Low latency busy poll timeout for socket reads. (needs CONFIG_NET_LL_RX_POLL) +Approximate time in us to busy loop waiting for packets on the device queue. +This sets the default value of the SO_LL socket option. +Can be set or overridden per socket by setting socket option SO_LL, which is +the preferred method of enabling. +If you need to enable the feature globally via sysctl, a value of 50 is recommended. +Will increase power usage. +Default: 0 (off) + +low_latency_poll +---------------- +Low latency busy poll timeout for poll and select. (needs CONFIG_NET_LL_RX_POLL) +Approximate time in us to busy loop waiting for events. +Recommended value depends on the number of sockets you poll on. +For several sockets 50, for several hundreds 100. +For more than that you probably want to use epoll. +Note that only sockets with SO_LL set will be busy polled, so you want to either +selectively set SO_LL on those sockets or set sysctl.net.low_latency_read globally. +Will increase power usage. +Default: 0 (off) + rmem_default ------------ @@ -93,8 +116,7 @@ netdev_budget Maximum number of packets taken from all interfaces in one polling cycle (NAPI poll). In one polling cycle interfaces which are registered to polling are -probed in a round-robin manner. The limit of packets in one such probe can be -set per-device via sysfs class/net/<device>/weight . +probed in a round-robin manner. netdev_max_backlog ------------------ @@ -201,3 +223,18 @@ IPX. The /proc/net/ipx_route table holds a list of IPX routes. For each route it gives the destination network, the router node (or Directly) and the network address of the router (or Connected) for internal networks. + +6. TIPC +------------------------------------------------------- + +The TIPC protocol now has a tunable for the receive memory, similar to the +tcp_rmem - i.e. a vector of 3 INTEGERs: (min, default, max) + + # cat /proc/sys/net/tipc/tipc_rmem + 4252725 34021800 68043600 + # + +The max value is set to CONN_OVERLOAD_LIMIT, and the default and min values +are scaled (shifted) versions of that same value. Note that the min value +is not at this point in time used in any meaningful way, but the triplet is +preserved in order to be consistent with things like tcp_rmem. |