diff options
Diffstat (limited to 'Documentation')
99 files changed, 1530 insertions, 456 deletions
diff --git a/Documentation/ABI/testing/sysfs-block-rssd b/Documentation/ABI/testing/sysfs-block-rssd index 679ce35..beef30c 100644 --- a/Documentation/ABI/testing/sysfs-block-rssd +++ b/Documentation/ABI/testing/sysfs-block-rssd @@ -1,26 +1,5 @@ -What: /sys/block/rssd*/registers -Date: March 2012 -KernelVersion: 3.3 -Contact: Asai Thambi S P <asamymuthupa@micron.com> -Description: This is a read-only file. Dumps below driver information and - hardware registers. - - S ACTive - - Command Issue - - Completed - - PORT IRQ STAT - - HOST IRQ STAT - - Allocated - - Commands in Q - What: /sys/block/rssd*/status Date: April 2012 KernelVersion: 3.4 Contact: Asai Thambi S P <asamymuthupa@micron.com> Description: This is a read-only file. Indicates the status of the device. - -What: /sys/block/rssd*/flags -Date: May 2012 -KernelVersion: 3.5 -Contact: Asai Thambi S P <asamymuthupa@micron.com> -Description: This is a read-only file. Dumps the flags in port and driver - data structure diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 5bc8a47..cfedf63 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -219,6 +219,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_scale What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_scale What: /sys/bus/iio/devices/iio:deviceX/in_voltage_scale What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_scale +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale What: /sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_scale @@ -273,6 +274,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale_available What: /sys/.../iio:deviceX/in_voltageX_scale_available What: /sys/.../iio:deviceX/in_voltage-voltage_scale_available What: /sys/.../iio:deviceX/out_voltageX_scale_available +What: /sys/.../iio:deviceX/out_altvoltageX_scale_available What: /sys/.../iio:deviceX/in_capacitance_scale_available KernelVersion: 2.635 Contact: linux-iio@vger.kernel.org @@ -298,14 +300,19 @@ Description: gives the 3dB frequency of the filter in Hz. What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_raw KernelVersion: 2.6.37 Contact: linux-iio@vger.kernel.org Description: Raw (unscaled, no bias etc.) output voltage for channel Y. The number must always be specified and unique if the output corresponds to a single channel. + While DAC like devices typically use out_voltage, + a continuous frequency generating device, such as + a DDS or PLL should use out_altvoltage. What: /sys/bus/iio/devices/iio:deviceX/out_voltageY&Z_raw +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY&Z_raw KernelVersion: 2.6.37 Contact: linux-iio@vger.kernel.org Description: @@ -316,6 +323,8 @@ Description: What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown_mode What: /sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown_mode +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown_mode +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown_mode KernelVersion: 2.6.38 Contact: linux-iio@vger.kernel.org Description: @@ -330,6 +339,8 @@ Description: What: /sys/.../iio:deviceX/out_votlageY_powerdown_mode_available What: /sys/.../iio:deviceX/out_voltage_powerdown_mode_available +What: /sys/.../iio:deviceX/out_altvotlageY_powerdown_mode_available +What: /sys/.../iio:deviceX/out_altvoltage_powerdown_mode_available KernelVersion: 2.6.38 Contact: linux-iio@vger.kernel.org Description: @@ -338,6 +349,8 @@ Description: What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown What: /sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown KernelVersion: 2.6.38 Contact: linux-iio@vger.kernel.org Description: @@ -346,6 +359,24 @@ Description: normal operation. Y may be suppressed if all outputs are controlled together. +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Output frequency for channel Y in Hz. The number must always be + specified and unique if the output corresponds to a single + channel. + +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_phase +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Phase in radians of one frequency/clock output Y + (out_altvoltageY) relative to another frequency/clock output + (out_altvoltageZ) of the device X. The number must always be + specified and unique if the output corresponds to a single + channel. + What: /sys/bus/iio/devices/iio:deviceX/events KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org diff --git a/Documentation/ABI/testing/sysfs-class-mtd b/Documentation/ABI/testing/sysfs-class-mtd index db1ad7e..938ef71 100644 --- a/Documentation/ABI/testing/sysfs-class-mtd +++ b/Documentation/ABI/testing/sysfs-class-mtd @@ -142,13 +142,14 @@ KernelVersion: 3.4 Contact: linux-mtd@lists.infradead.org Description: This allows the user to examine and adjust the criteria by which - mtd returns -EUCLEAN from mtd_read(). If the maximum number of - bit errors that were corrected on any single region comprising - an ecc step (as reported by the driver) equals or exceeds this - value, -EUCLEAN is returned. Otherwise, absent an error, 0 is - returned. Higher layers (e.g., UBI) use this return code as an - indication that an erase block may be degrading and should be - scrutinized as a candidate for being marked as bad. + mtd returns -EUCLEAN from mtd_read() and mtd_read_oob(). If the + maximum number of bit errors that were corrected on any single + region comprising an ecc step (as reported by the driver) equals + or exceeds this value, -EUCLEAN is returned. Otherwise, absent + an error, 0 is returned. Higher layers (e.g., UBI) use this + return code as an indication that an erase block may be + degrading and should be scrutinized as a candidate for being + marked as bad. The initial value may be specified by the flash device driver. If not, then the default value is ecc_strength. @@ -167,7 +168,7 @@ Description: block degradation, but high enough to avoid the consequences of a persistent return value of -EUCLEAN on devices where sticky bitflips occur. Note that if bitflip_threshold exceeds - ecc_strength, -EUCLEAN is never returned by mtd_read(). + ecc_strength, -EUCLEAN is never returned by the read operations. Conversely, if bitflip_threshold is zero, -EUCLEAN is always returned, absent a hard error. diff --git a/Documentation/ABI/testing/sysfs-power b/Documentation/ABI/testing/sysfs-power index 31725ff..2177726 100644 --- a/Documentation/ABI/testing/sysfs-power +++ b/Documentation/ABI/testing/sysfs-power @@ -231,3 +231,16 @@ Description: Reads from this file return a string consisting of the names of wakeup sources created with the help of /sys/power/wake_lock that are inactive at the moment, separated with spaces. + +What: /sys/power/pm_print_times +Date: May 2012 +Contact: Sameer Nanda <snanda@chromium.org> +Description: + The /sys/power/pm_print_times file allows user space to + control whether the time taken by devices to suspend and + resume is printed. These prints are useful for hunting down + devices that take too long to suspend or resume. + + Writing a "1" enables this printing while writing a "0" + disables it. The default value is "0". Reading from this file + will display the current value. diff --git a/Documentation/DocBook/80211.tmpl b/Documentation/DocBook/80211.tmpl index f3e214f..42e7f03 100644 --- a/Documentation/DocBook/80211.tmpl +++ b/Documentation/DocBook/80211.tmpl @@ -404,7 +404,6 @@ !Finclude/net/mac80211.h ieee80211_get_tkip_p1k !Finclude/net/mac80211.h ieee80211_get_tkip_p1k_iv !Finclude/net/mac80211.h ieee80211_get_tkip_p2k -!Finclude/net/mac80211.h ieee80211_key_removed </chapter> <chapter id="powersave"> diff --git a/Documentation/DocBook/media/v4l/controls.xml b/Documentation/DocBook/media/v4l/controls.xml index 676bc46..cda0dfb 100644 --- a/Documentation/DocBook/media/v4l/controls.xml +++ b/Documentation/DocBook/media/v4l/controls.xml @@ -3988,7 +3988,7 @@ interface and may change in the future.</para> from RGB to Y'CbCr color space. </entry> </row> - <row id = "v4l2-jpeg-chroma-subsampling"> + <row> <entrytbl spanname="descr" cols="2"> <tbody valign="top"> <row> diff --git a/Documentation/DocBook/media/v4l/pixfmt.xml b/Documentation/DocBook/media/v4l/pixfmt.xml index f5ac15e..e58934c 100644 --- a/Documentation/DocBook/media/v4l/pixfmt.xml +++ b/Documentation/DocBook/media/v4l/pixfmt.xml @@ -986,13 +986,13 @@ http://www.thedirks.org/winnov/</ulink></para></entry> <row id="V4L2-PIX-FMT-Y4"> <entry><constant>V4L2_PIX_FMT_Y4</constant></entry> <entry>'Y04 '</entry> - <entry>Old 4-bit greyscale format. Only the least significant 4 bits of each byte are used, + <entry>Old 4-bit greyscale format. Only the most significant 4 bits of each byte are used, the other bits are set to 0.</entry> </row> <row id="V4L2-PIX-FMT-Y6"> <entry><constant>V4L2_PIX_FMT_Y6</constant></entry> <entry>'Y06 '</entry> - <entry>Old 6-bit greyscale format. Only the least significant 6 bits of each byte are used, + <entry>Old 6-bit greyscale format. Only the most significant 6 bits of each byte are used, the other bits are set to 0.</entry> </row> </tbody> diff --git a/Documentation/DocBook/media/v4l/v4l2.xml b/Documentation/DocBook/media/v4l/v4l2.xml index 015c561..008c2d7 100644 --- a/Documentation/DocBook/media/v4l/v4l2.xml +++ b/Documentation/DocBook/media/v4l/v4l2.xml @@ -560,6 +560,7 @@ and discussions on the V4L mailing list.</revremark> &sub-g-tuner; &sub-log-status; &sub-overlay; + &sub-prepare-buf; &sub-qbuf; &sub-querybuf; &sub-querycap; @@ -567,7 +568,6 @@ and discussions on the V4L mailing list.</revremark> &sub-query-dv-preset; &sub-query-dv-timings; &sub-querystd; - &sub-prepare-buf; &sub-reqbufs; &sub-s-hw-freq-seek; &sub-streamon; diff --git a/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml b/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml index 765549f..a2474ec 100644 --- a/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml +++ b/Documentation/DocBook/media/v4l/vidioc-create-bufs.xml @@ -108,10 +108,9 @@ information.</para> /></entry> </row> <row> - <entry>__u32</entry> + <entry>struct v4l2_format</entry> <entry><structfield>format</structfield></entry> - <entry>Filled in by the application, preserved by the driver. - See <xref linkend="v4l2-format" />.</entry> + <entry>Filled in by the application, preserved by the driver.</entry> </row> <row> <entry>__u32</entry> diff --git a/Documentation/DocBook/media/v4l/vidioc-dqevent.xml b/Documentation/DocBook/media/v4l/vidioc-dqevent.xml index e8714aa..98a856f 100644 --- a/Documentation/DocBook/media/v4l/vidioc-dqevent.xml +++ b/Documentation/DocBook/media/v4l/vidioc-dqevent.xml @@ -89,7 +89,7 @@ <row> <entry></entry> <entry>&v4l2-event-frame-sync;</entry> - <entry><structfield>frame</structfield></entry> + <entry><structfield>frame_sync</structfield></entry> <entry>Event data for event V4L2_EVENT_FRAME_SYNC.</entry> </row> <row> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml b/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml index e3d5afcd..0a4b90f 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml @@ -284,13 +284,6 @@ These controls are described in <xref processing controls. These controls are described in <xref linkend="image-process-controls" />.</entry> </row> - <row> - <entry><constant>V4L2_CTRL_CLASS_JPEG</constant></entry> - <entry>0x9d0000</entry> - <entry>The class containing JPEG compression controls. -These controls are described in <xref - linkend="jpeg-controls" />.</entry> - </row> </tbody> </tgroup> </table> diff --git a/Documentation/RCU/checklist.txt b/Documentation/RCU/checklist.txt index 5c8d749..fc103d7 100644 --- a/Documentation/RCU/checklist.txt +++ b/Documentation/RCU/checklist.txt @@ -162,9 +162,9 @@ over a rather long period of time, but improvements are always welcome! when publicizing a pointer to a structure that can be traversed by an RCU read-side critical section. -5. If call_rcu(), or a related primitive such as call_rcu_bh() or - call_rcu_sched(), is used, the callback function must be - written to be called from softirq context. In particular, +5. If call_rcu(), or a related primitive such as call_rcu_bh(), + call_rcu_sched(), or call_srcu() is used, the callback function + must be written to be called from softirq context. In particular, it cannot block. 6. Since synchronize_rcu() can block, it cannot be called from @@ -202,11 +202,12 @@ over a rather long period of time, but improvements are always welcome! updater uses call_rcu_sched() or synchronize_sched(), then the corresponding readers must disable preemption, possibly by calling rcu_read_lock_sched() and rcu_read_unlock_sched(). - If the updater uses synchronize_srcu(), the the corresponding - readers must use srcu_read_lock() and srcu_read_unlock(), - and with the same srcu_struct. The rules for the expedited - primitives are the same as for their non-expedited counterparts. - Mixing things up will result in confusion and broken kernels. + If the updater uses synchronize_srcu() or call_srcu(), + the the corresponding readers must use srcu_read_lock() and + srcu_read_unlock(), and with the same srcu_struct. The rules for + the expedited primitives are the same as for their non-expedited + counterparts. Mixing things up will result in confusion and + broken kernels. One exception to this rule: rcu_read_lock() and rcu_read_unlock() may be substituted for rcu_read_lock_bh() and rcu_read_unlock_bh() @@ -333,14 +334,14 @@ over a rather long period of time, but improvements are always welcome! victim CPU from ever going offline.) 14. SRCU (srcu_read_lock(), srcu_read_unlock(), srcu_dereference(), - synchronize_srcu(), and synchronize_srcu_expedited()) may only - be invoked from process context. Unlike other forms of RCU, it - -is- permissible to block in an SRCU read-side critical section - (demarked by srcu_read_lock() and srcu_read_unlock()), hence the - "SRCU": "sleepable RCU". Please note that if you don't need - to sleep in read-side critical sections, you should be using - RCU rather than SRCU, because RCU is almost always faster and - easier to use than is SRCU. + synchronize_srcu(), synchronize_srcu_expedited(), and call_srcu()) + may only be invoked from process context. Unlike other forms of + RCU, it -is- permissible to block in an SRCU read-side critical + section (demarked by srcu_read_lock() and srcu_read_unlock()), + hence the "SRCU": "sleepable RCU". Please note that if you + don't need to sleep in read-side critical sections, you should be + using RCU rather than SRCU, because RCU is almost always faster + and easier to use than is SRCU. If you need to enter your read-side critical section in a hardirq or exception handler, and then exit that same read-side @@ -353,8 +354,8 @@ over a rather long period of time, but improvements are always welcome! cleanup_srcu_struct(). These are passed a "struct srcu_struct" that defines the scope of a given SRCU domain. Once initialized, the srcu_struct is passed to srcu_read_lock(), srcu_read_unlock() - synchronize_srcu(), and synchronize_srcu_expedited(). A given - synchronize_srcu() waits only for SRCU read-side critical + synchronize_srcu(), synchronize_srcu_expedited(), and call_srcu(). + A given synchronize_srcu() waits only for SRCU read-side critical sections governed by srcu_read_lock() and srcu_read_unlock() calls that have been passed the same srcu_struct. This property is what makes sleeping read-side critical sections tolerable -- @@ -374,7 +375,7 @@ over a rather long period of time, but improvements are always welcome! requiring SRCU's read-side deadlock immunity or low read-side realtime latency. - Note that, rcu_assign_pointer() relates to SRCU just as they do + Note that, rcu_assign_pointer() relates to SRCU just as it does to other forms of RCU. 15. The whole point of call_rcu(), synchronize_rcu(), and friends diff --git a/Documentation/RCU/rcubarrier.txt b/Documentation/RCU/rcubarrier.txt index e439a0e..38428c1 100644 --- a/Documentation/RCU/rcubarrier.txt +++ b/Documentation/RCU/rcubarrier.txt @@ -79,8 +79,6 @@ complete. Pseudo-code using rcu_barrier() is as follows: 2. Execute rcu_barrier(). 3. Allow the module to be unloaded. -Quick Quiz #1: Why is there no srcu_barrier()? - The rcutorture module makes use of rcu_barrier in its exit function as follows: @@ -162,7 +160,7 @@ for any pre-existing callbacks to complete. Then lines 55-62 print status and do operation-specific cleanup, and then return, permitting the module-unload operation to be completed. -Quick Quiz #2: Is there any other situation where rcu_barrier() might +Quick Quiz #1: Is there any other situation where rcu_barrier() might be required? Your module might have additional complications. For example, if your @@ -242,7 +240,7 @@ reaches zero, as follows: 4 complete(&rcu_barrier_completion); 5 } -Quick Quiz #3: What happens if CPU 0's rcu_barrier_func() executes +Quick Quiz #2: What happens if CPU 0's rcu_barrier_func() executes immediately (thus incrementing rcu_barrier_cpu_count to the value one), but the other CPU's rcu_barrier_func() invocations are delayed for a full grace period? Couldn't this result in @@ -259,12 +257,7 @@ so that your module may be safely unloaded. Answers to Quick Quizzes -Quick Quiz #1: Why is there no srcu_barrier()? - -Answer: Since there is no call_srcu(), there can be no outstanding SRCU - callbacks. Therefore, there is no need to wait for them. - -Quick Quiz #2: Is there any other situation where rcu_barrier() might +Quick Quiz #1: Is there any other situation where rcu_barrier() might be required? Answer: Interestingly enough, rcu_barrier() was not originally @@ -278,7 +271,7 @@ Answer: Interestingly enough, rcu_barrier() was not originally implementing rcutorture, and found that rcu_barrier() solves this problem as well. -Quick Quiz #3: What happens if CPU 0's rcu_barrier_func() executes +Quick Quiz #2: What happens if CPU 0's rcu_barrier_func() executes immediately (thus incrementing rcu_barrier_cpu_count to the value one), but the other CPU's rcu_barrier_func() invocations are delayed for a full grace period? Couldn't this result in diff --git a/Documentation/RCU/torture.txt b/Documentation/RCU/torture.txt index 4ddf391..7dce8a1 100644 --- a/Documentation/RCU/torture.txt +++ b/Documentation/RCU/torture.txt @@ -174,11 +174,20 @@ torture_type The type of RCU to test, with string values as follows: and synchronize_rcu_bh_expedited(). "srcu": srcu_read_lock(), srcu_read_unlock() and + call_srcu(). + + "srcu_sync": srcu_read_lock(), srcu_read_unlock() and synchronize_srcu(). "srcu_expedited": srcu_read_lock(), srcu_read_unlock() and synchronize_srcu_expedited(). + "srcu_raw": srcu_read_lock_raw(), srcu_read_unlock_raw(), + and call_srcu(). + + "srcu_raw_sync": srcu_read_lock_raw(), srcu_read_unlock_raw(), + and synchronize_srcu(). + "sched": preempt_disable(), preempt_enable(), and call_rcu_sched(). diff --git a/Documentation/RCU/whatisRCU.txt b/Documentation/RCU/whatisRCU.txt index 6bbe8dc..69ee188 100644 --- a/Documentation/RCU/whatisRCU.txt +++ b/Documentation/RCU/whatisRCU.txt @@ -833,9 +833,9 @@ sched: Critical sections Grace period Barrier SRCU: Critical sections Grace period Barrier - srcu_read_lock synchronize_srcu N/A - srcu_read_unlock synchronize_srcu_expedited - srcu_read_lock_raw + srcu_read_lock synchronize_srcu srcu_barrier + srcu_read_unlock call_srcu + srcu_read_lock_raw synchronize_srcu_expedited srcu_read_unlock_raw srcu_dereference diff --git a/Documentation/arm/SPEAr/overview.txt b/Documentation/arm/SPEAr/overview.txt index 57aae77..65610bf 100644 --- a/Documentation/arm/SPEAr/overview.txt +++ b/Documentation/arm/SPEAr/overview.txt @@ -60,4 +60,4 @@ Introduction Document Author --------------- - Viresh Kumar <viresh.kumar@st.com>, (c) 2010-2012 ST Microelectronics + Viresh Kumar <viresh.linux@gmail.com>, (c) 2010-2012 ST Microelectronics diff --git a/Documentation/connector/cn_test.c b/Documentation/connector/cn_test.c index 7764594..adcca03 100644 --- a/Documentation/connector/cn_test.c +++ b/Documentation/connector/cn_test.c @@ -69,9 +69,13 @@ static int cn_test_want_notify(void) return -ENOMEM; } - nlh = NLMSG_PUT(skb, 0, 0x123, NLMSG_DONE, size - sizeof(*nlh)); + nlh = nlmsg_put(skb, 0, 0x123, NLMSG_DONE, size - sizeof(*nlh), 0); + if (!nlh) { + kfree_skb(skb); + return -EMSGSIZE; + } - msg = (struct cn_msg *)NLMSG_DATA(nlh); + msg = nlmsg_data(nlh); memset(msg, 0, size0); @@ -117,11 +121,6 @@ static int cn_test_want_notify(void) pr_info("request was sent: group=0x%x\n", ctl->group); return 0; - -nlmsg_failure: - pr_err("failed to send %u.%u\n", msg->seq, msg->ack); - kfree_skb(skb); - return -EINVAL; } #endif diff --git a/Documentation/device-mapper/verity.txt b/Documentation/device-mapper/verity.txt index 32e4879..9884681 100644 --- a/Documentation/device-mapper/verity.txt +++ b/Documentation/device-mapper/verity.txt @@ -7,39 +7,39 @@ This target is read-only. Construction Parameters ======================= - <version> <dev> <hash_dev> <hash_start> + <version> <dev> <hash_dev> <data_block_size> <hash_block_size> <num_data_blocks> <hash_start_block> <algorithm> <digest> <salt> <version> - This is the version number of the on-disk format. + This is the type of the on-disk hash format. 0 is the original format used in the Chromium OS. - The salt is appended when hashing, digests are stored continuously and - the rest of the block is padded with zeros. + The salt is appended when hashing, digests are stored continuously and + the rest of the block is padded with zeros. 1 is the current format that should be used for new devices. - The salt is prepended when hashing and each digest is - padded with zeros to the power of two. + The salt is prepended when hashing and each digest is + padded with zeros to the power of two. <dev> - This is the device containing the data the integrity of which needs to be + This is the device containing data, the integrity of which needs to be checked. It may be specified as a path, like /dev/sdaX, or a device number, <major>:<minor>. <hash_dev> - This is the device that that supplies the hash tree data. It may be + This is the device that supplies the hash tree data. It may be specified similarly to the device path and may be the same device. If the - same device is used, the hash_start should be outside of the dm-verity - configured device size. + same device is used, the hash_start should be outside the configured + dm-verity device. <data_block_size> - The block size on a data device. Each block corresponds to one digest on - the hash device. + The block size on a data device in bytes. + Each block corresponds to one digest on the hash device. <hash_block_size> - The size of a hash block. + The size of a hash block in bytes. <num_data_blocks> The number of data blocks on the data device. Additional blocks are @@ -65,7 +65,7 @@ Construction Parameters Theory of operation =================== -dm-verity is meant to be setup as part of a verified boot path. This +dm-verity is meant to be set up as part of a verified boot path. This may be anything ranging from a boot using tboot or trustedgrub to just booting from a known-good device (like a USB drive or CD). @@ -73,20 +73,20 @@ When a dm-verity device is configured, it is expected that the caller has been authenticated in some way (cryptographic signatures, etc). After instantiation, all hashes will be verified on-demand during disk access. If they cannot be verified up to the root node of the -tree, the root hash, then the I/O will fail. This should identify +tree, the root hash, then the I/O will fail. This should detect tampering with any data on the device and the hash data. Cryptographic hashes are used to assert the integrity of the device on a -per-block basis. This allows for a lightweight hash computation on first read -into the page cache. Block hashes are stored linearly-aligned to the nearest -block the size of a page. +per-block basis. This allows for a lightweight hash computation on first read +into the page cache. Block hashes are stored linearly, aligned to the nearest +block size. Hash Tree --------- Each node in the tree is a cryptographic hash. If it is a leaf node, the hash -is of some block data on disk. If it is an intermediary node, then the hash is -of a number of child nodes. +of some data block on disk is calculated. If it is an intermediary node, +the hash of a number of child nodes is calculated. Each entry in the tree is a collection of neighboring nodes that fit in one block. The number is determined based on block_size and the size of the @@ -110,63 +110,23 @@ alg = sha256, num_blocks = 32768, block_size = 4096 On-disk format ============== -Below is the recommended on-disk format. The verity kernel code does not -read the on-disk header. It only reads the hash blocks which directly -follow the header. It is expected that a user-space tool will verify the -integrity of the verity_header and then call dmsetup with the correct -parameters. Alternatively, the header can be omitted and the dmsetup -parameters can be passed via the kernel command-line in a rooted chain -of trust where the command-line is verified. +The verity kernel code does not read the verity metadata on-disk header. +It only reads the hash blocks which directly follow the header. +It is expected that a user-space tool will verify the integrity of the +verity header. -The on-disk format is especially useful in cases where the hash blocks -are on a separate partition. The magic number allows easy identification -of the partition contents. Alternatively, the hash blocks can be stored -in the same partition as the data to be verified. In such a configuration -the filesystem on the partition would be sized a little smaller than -the full-partition, leaving room for the hash blocks. - -struct superblock { - uint8_t signature[8] - "verity\0\0"; - - uint8_t version; - 1 - current format - - uint8_t data_block_bits; - log2(data block size) - - uint8_t hash_block_bits; - log2(hash block size) - - uint8_t pad1[1]; - zero padding - - uint16_t salt_size; - big-endian salt size - - uint8_t pad2[2]; - zero padding - - uint32_t data_blocks_hi; - big-endian high 32 bits of the 64-bit number of data blocks - - uint32_t data_blocks_lo; - big-endian low 32 bits of the 64-bit number of data blocks - - uint8_t algorithm[16]; - cryptographic algorithm - - uint8_t salt[384]; - salt (the salt size is specified above) - - uint8_t pad3[88]; - zero padding to 512-byte boundary -} +Alternatively, the header can be omitted and the dmsetup parameters can +be passed via the kernel command-line in a rooted chain of trust where +the command-line is verified. Directly following the header (and with sector number padded to the next hash block boundary) are the hash blocks which are stored a depth at a time (starting from the root), sorted in order of increasing index. +The full specification of kernel parameters and on-disk metadata format +is available at the cryptsetup project's wiki page + http://code.google.com/p/cryptsetup/wiki/DMVerity + Status ====== V (for Valid) is returned if every check performed so far was valid. @@ -174,21 +134,22 @@ If any check failed, C (for Corruption) is returned. Example ======= - -Setup a device: - dmsetup create vroot --table \ - "0 2097152 "\ - "verity 1 /dev/sda1 /dev/sda2 4096 4096 2097152 1 "\ +Set up a device: + # dmsetup create vroot --readonly --table \ + "0 2097152 verity 1 /dev/sda1 /dev/sda2 4096 4096 262144 1 sha256 "\ "4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076 "\ "1234000000000000000000000000000000000000000000000000000000000000" A command line tool veritysetup is available to compute or verify -the hash tree or activate the kernel driver. This is available from -the LVM2 upstream repository and may be supplied as a package called -device-mapper-verity-tools: - git://sources.redhat.com/git/lvm2 - http://sourceware.org/git/?p=lvm2.git - http://sourceware.org/cgi-bin/cvsweb.cgi/LVM2/verity?cvsroot=lvm2 - -veritysetup -a vroot /dev/sda1 /dev/sda2 \ - 4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076 +the hash tree or activate the kernel device. This is available from +the cryptsetup upstream repository http://code.google.com/p/cryptsetup/ +(as a libcryptsetup extension). + +Create hash on the device: + # veritysetup format /dev/sda1 /dev/sda2 + ... + Root hash: 4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076 + +Activate the device: + # veritysetup create vroot /dev/sda1 /dev/sda2 \ + 4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076 diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt new file mode 100644 index 0000000..70c0dc5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt @@ -0,0 +1,23 @@ +Marvell Armada 370 and Armada XP Interrupt Controller +----------------------------------------------------- + +Required properties: +- compatible: Should be "marvell,mpic" +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt-cells: The number of cells to define the interrupts. Should be 1. + The cell is the IRQ number +- reg: Should contain PMIC registers location and length. First pair + for the main interrupt registers, second pair for the per-CPU + interrupt registers + +Example: + + mpic: interrupt-controller@d0020000 { + compatible = "marvell,mpic"; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + interrupt-controller; + reg = <0xd0020000 0x1000>, + <0xd0021000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt new file mode 100644 index 0000000..8b6ea22 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt @@ -0,0 +1,11 @@ +Marvell Armada 370 and Armada XP Global Timers +---------------------------------------------- + +Required properties: +- compatible: Should be "marvell,armada-370-xp-timer" +- interrupts: Should contain the list of Global Timer interrupts +- reg: Should contain the base address of the Global Timer registers + +Optional properties: +- marvell,timer-25Mhz: Tells whether the Global timer supports the 25 + Mhz fixed mode (available on Armada XP and not on Armada 370) diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp.txt b/Documentation/devicetree/bindings/arm/armada-370-xp.txt new file mode 100644 index 0000000..c6ed90e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-370-xp.txt @@ -0,0 +1,24 @@ +Marvell Armada 370 and Armada XP Platforms Device Tree Bindings +--------------------------------------------------------------- + +Boards with a SoC of the Marvell Armada 370 and Armada XP families +shall have the following property: + +Required root node property: + +compatible: must contain "marvell,armada-370-xp" + +In addition, boards using the Marvell Armada 370 SoC shall have the +following property: + +Required root node property: + +compatible: must contain "marvell,armada370" + +In addition, boards using the Marvell Armada XP SoC shall have the +following property: + +Required root node property: + +compatible: must contain "marvell,armadaxp" + diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt index aabca4f..19078bf 100644 --- a/Documentation/devicetree/bindings/arm/atmel-aic.txt +++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt @@ -4,7 +4,7 @@ Required properties: - compatible: Should be "atmel,<chip>-aic" - interrupt-controller: Identifies the node as an interrupt controller. - interrupt-parent: For single AIC system, it is an empty property. -- #interrupt-cells: The number of cells to define the interrupts. It sould be 2. +- #interrupt-cells: The number of cells to define the interrupts. It sould be 3. The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet). The second cell is used to specify flags: bits[3:0] trigger type and level flags: @@ -14,7 +14,10 @@ Required properties: 8 = active low level-sensitive. Valid combinations are 1, 2, 3, 4, 8. Default flag for internal sources should be set to 4 (active high). + The third cell is used to specify the irq priority from 0 (lowest) to 7 + (highest). - reg: Should contain AIC registers location and length +- atmel,external-irqs: u32 array of external irqs. Examples: /* @@ -24,7 +27,7 @@ Examples: compatible = "atmel,at91rm9200-aic"; interrupt-controller; interrupt-parent; - #interrupt-cells = <2>; + #interrupt-cells = <3>; reg = <0xfffff000 0x200>; }; @@ -34,5 +37,5 @@ Examples: dma: dma-controller@ffffec00 { compatible = "atmel,at91sam9g45-dma"; reg = <0xffffec00 0x200>; - interrupts = <21 4>; + interrupts = <21 4 5>; }; diff --git a/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt new file mode 100644 index 0000000..597e8a0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt @@ -0,0 +1,27 @@ +* TI Common Platform Interrupt Controller + +Common Platform Interrupt Controller (cp_intc) is used on +OMAP-L1x SoCs and can support several configurable number +of interrupts. + +Main node required properties: + +- compatible : should be: + "ti,cp-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. + + The cell contains the interrupt number in the range [0-128]. +- ti,intc-size: Number of interrupts handled by the interrupt controller. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller@1 { + compatible = "ti,cp-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <101>; + reg = <0xfffee000 0x2000>; + }; diff --git a/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt b/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt new file mode 100644 index 0000000..081c6a7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt @@ -0,0 +1,17 @@ +MVEBU System Controller +----------------------- +MVEBU (Marvell SOCs: Armada 370/XP, Dove, mv78xx0, Kirkwood, Orion5x) + +Required properties: + +- compatible: one of: + - "marvell,orion-system-controller" + - "marvell,armada-370-xp-system-controller" +- reg: Should contain system controller registers location and length. + +Example: + + system-controller@d0018200 { + compatible = "marvell,armada-370-xp-system-controller"; + reg = <0xd0018200 0x500>; + }; diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt new file mode 100644 index 0000000..007fb5c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/olimex.txt @@ -0,0 +1,6 @@ +Olimex i.MX Platforms Device Tree Bindings +------------------------------------------ + +i.MX23 Olinuxino Low Cost Board +Required root node properties: + - compatible = "olimex,imx23-olinuxino", "fsl,imx23"; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index e78e8bc..ccdd0e5 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -47,3 +47,9 @@ Boards: - AM335X EVM : Software Developement Board for AM335x compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" + +- AM335X Bone : Low cost community board + compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" + +- OMAP5 EVM : Evaluation Module + compatible = "ti,omap5-evm", "ti,omap5" diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-emc.txt index 09335f8..4c33b29 100644 --- a/Documentation/devicetree/bindings/arm/tegra/emc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-emc.txt @@ -15,7 +15,7 @@ Child device nodes describe the memory settings for different configurations and Example: - emc@7000f400 { + memory-controller@7000f400 { #address-cells = < 1 >; #size-cells = < 0 >; compatible = "nvidia,tegra20-emc"; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt index c25a0a5..866d934 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt @@ -8,7 +8,7 @@ Required properties: - interrupts : Should contain MC General interrupt. Example: - mc { + memory-controller@0x7000f000 { compatible = "nvidia,tegra20-mc"; reg = <0x7000f000 0x024 0x7000f03c 0x3c4>; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt index e47e73f..bdf1a61 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt @@ -8,7 +8,7 @@ Required properties: - interrupts : Should contain MC General interrupt. Example: - mc { + memory-controller { compatible = "nvidia,tegra30-mc"; reg = <0x7000f000 0x010 0x7000f03c 0x1b4 diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt new file mode 100644 index 0000000..b41e5e52 --- /dev/null +++ b/Documentation/devicetree/bindings/fb/mxsfb.txt @@ -0,0 +1,19 @@ +* Freescale MXS LCD Interface (LCDIF) + +Required properties: +- compatible: Should be "fsl,<chip>-lcdif". Supported chips include + imx23 and imx28. +- reg: Address and length of the register set for lcdif +- interrupts: Should contain lcdif interrupts + +Optional properties: +- panel-enable-gpios : Should specify the gpio for panel enable + +Examples: + +lcdif@80030000 { + compatible = "fsl,imx28-lcdif"; + reg = <0x80030000 2000>; + interrupts = <38 86>; + panel-enable-gpios = <&gpio3 30 0>; +}; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt index 4363ae4..4f39297 100644 --- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -8,8 +8,16 @@ Required properties: by low 16 pins and the second one is for high 16 pins. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. Example: @@ -19,4 +27,6 @@ gpio0: gpio@73f84000 { interrupts = <50 51>; gpio-controller; #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt index 0c35673..1e677a4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt @@ -13,8 +13,9 @@ Required properties for GPIO node: - interrupts : Should be the port interrupt shared by all 32 pins. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low - interrupt-controller: Marks the device node as an interrupt controller. - #interrupt-cells : Should be 2. The first cell is the GPIO number. The second cell bits[3:0] is used to specify trigger type and level flags: diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt index ee87467..8315ac7 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt @@ -26,6 +26,6 @@ Example: #gpio-cells = <2>; gpio-controller; interrupt-controller; - supports-sleepmode; + st,supports-sleepmode; gpio-bank = <1>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt index 023c952..023c952 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt new file mode 100644 index 0000000..ae8af16 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt @@ -0,0 +1,93 @@ +Pinctrl-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses pin multiplexing to +route the I2C signals, and represents the pin multiplexing configuration +using the pinctrl device tree bindings. + + +-----+ +-----+ + | dev | | dev | + +------------------------+ +-----+ +-----+ + | SoC | | | + | /----|------+--------+ + | +---+ +------+ | child bus A, on first set of pins + | |I2C|---|Pinmux| | + | +---+ +------+ | child bus B, on second set of pins + | \----|------+--------+--------+ + | | | | | + +------------------------+ +-----+ +-----+ +-----+ + | dev | | dev | | dev | + +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-pinctrl +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. + +Also required are: + +* Standard pinctrl properties that specify the pin mux state for each child + bus. See ../pinctrl/pinctrl-bindings.txt. + +* Standard I2C mux properties. See mux.txt in this directory. + +* I2C child bus nodes. See mux.txt in this directory. + +For each named state defined in the pinctrl-names property, an I2C child bus +will be created. I2C child bus numbers are assigned based on the index into +the pinctrl-names property. + +The only exception is that no bus will be created for a state named "idle". If +such a state is defined, it must be the last entry in pinctrl-names. For +example: + + pinctrl-names = "ddc", "pta", "idle" -> ddc = bus 0, pta = bus 1 + pinctrl-names = "ddc", "idle", "pta" -> Invalid ("idle" not last) + pinctrl-names = "idle", "ddc", "pta" -> Invalid ("idle" not last) + +Whenever an access is made to a device on a child bus, the relevant pinctrl +state will be programmed into hardware. + +If an idle state is defined, whenever an access is not being made to a device +on a child bus, the idle pinctrl state will be programmed into hardware. + +If an idle state is not defined, the most recently used pinctrl state will be +left programmed into hardware whenever no access is being made of a device on +a child bus. + +Example: + + i2cmux { + compatible = "i2c-mux-pinctrl"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&i2c1>; + + pinctrl-names = "ddc", "pta", "idle"; + pinctrl-0 = <&state_i2cmux_ddc>; + pinctrl-1 = <&state_i2cmux_pta>; + pinctrl-2 = <&state_i2cmux_idle>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom { + compatible = "eeprom"; + reg = <0x50>; + }; + }; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom { + compatible = "eeprom"; + reg = <0x50>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/input/fsl-mma8450.txt b/Documentation/devicetree/bindings/input/fsl-mma8450.txt index a00c94c..0b96e57 100644 --- a/Documentation/devicetree/bindings/input/fsl-mma8450.txt +++ b/Documentation/devicetree/bindings/input/fsl-mma8450.txt @@ -2,6 +2,7 @@ Required properties: - compatible : "fsl,mma8450". +- reg: the I2C address of MMA8450 Example: diff --git a/Documentation/devicetree/bindings/input/tegra-kbc.txt b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt index 72683be..72683be 100644 --- a/Documentation/devicetree/bindings/input/tegra-kbc.txt +++ b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index 19f6af4..baf0798 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -46,8 +46,8 @@ Examples: ecspi@70010000 { /* ECSPI1 */ fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ - <&gpio3 25 0>; /* GPIO4_25 */ + cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ + <&gpio4 25 0>; /* GPIO4_25 */ status = "okay"; pmic: mc13892@0 { diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index 645f5ea..d2802d4 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -17,18 +17,46 @@ Required properties: device need to be present. The definition for each of these nodes is defined using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. - The valid names for regulators are: + The valid regulator-compatible values are: tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, vaux2, vaux33, vmmc tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8 +- xxx-supply: Input voltage supply regulator. + These entries are require if regulators are enabled for a device. Missing of these + properties can cause the regulator registration fails. + If some of input supply is powered through battery or always-on supply then + also it is require to have these parameters with proper node handle of always + on power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + Optional properties: - ti,vmbch-threshold: (tps65911) main battery charged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) - ti,vmbch2-threshold: (tps65911) main battery discharged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL + in TPS6591X datasheet) - ti,en-gpio-sleep: enable sleep control for gpios There should be 9 entries here, one for each gpio. @@ -56,74 +84,110 @@ Example: ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <...>; + vcc4-supply = <...>; + vcc5-supply = <...>; + vcc6-supply = <...>; + vcc7-supply = <...>; + vccio-supply = <...>; + regulators { - vdd1_reg: vdd1 { + #address-cells = <1>; + #size-cells = <0>; + + vdd1_reg: regulator@0 { + regulator-compatible = "vdd1"; + reg = <0>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vdd2_reg: vdd2 { + vdd2_reg: regulator@1 { + regulator-compatible = "vdd2"; + reg = <1>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <4>; }; - vddctrl_reg: vddctrl { + vddctrl_reg: regulator@2 { + regulator-compatible = "vddctrl"; + reg = <2>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1400000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vio_reg: vio { + vio_reg: regulator@3 { + regulator-compatible = "vio"; + reg = <3>; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + regulator-compatible = "ldo1"; + reg = <4>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + regulator-compatible = "ldo2"; + reg = <5>; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; ti,regulator-ext-sleep-control = <0>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + regulator-compatible = "ldo3"; + reg = <6>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + regulator-compatible = "ldo4"; + reg = <7>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; ti,regulator-ext-sleep-control = <0>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + regulator-compatible = "ldo5"; + reg = <8>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + regulator-compatible = "ldo6"; + reg = <9>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; ti,regulator-ext-sleep-control = <0>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + regulator-compatible = "ldo7"; + reg = <10>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + regulator-compatible = "ldo8"; + reg = <11>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index 0d93b4b..bd9be0b 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -3,21 +3,22 @@ The Enhanced Secure Digital Host Controller provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc driver. + Required properties: - - compatible : should be - "fsl,<chip>-esdhc", "fsl,esdhc" - - reg : should contain eSDHC registers location and length. - - interrupts : should contain eSDHC interrupt. - interrupt-parent : interrupt source phandle. - clock-frequency : specifies eSDHC base clock frequency. - - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; New devices should use - the generic "wp-inverted" property. - - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. New devices should use the - generic "bus-width = <1>" property. - - sdhci,auto-cmd12: (optional) specifies that a controller can - only handle auto CMD12. + +Optional properties: + - sdhci,wp-inverted : specifies that eSDHC controller reports + inverted write-protect state; New devices should use the generic + "wp-inverted" property. + - sdhci,1-bit-only : specifies that a controller can only handle + 1-bit data transfers. New devices should use the generic + "bus-width = <1>" property. + - sdhci,auto-cmd12: specifies that a controller can only handle auto + CMD12. Example: diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index c7e404b..70cd49b 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -3,17 +3,15 @@ The Enhanced Secure Digital Host Controller on Freescale i.MX family provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc-imx driver. + Required properties: - compatible : Should be "fsl,<chip>-esdhc" -- reg : Should contain eSDHC registers location and length -- interrupts : Should contain eSDHC interrupt Optional properties: -- non-removable : Indicate the card is wired to host permanently - fsl,cd-internal : Indicate to use controller internal card detection - fsl,wp-internal : Indicate to use controller internal write protection -- cd-gpios : Specify GPIOs for card detection -- wp-gpios : Specify GPIOs for write protection Examples: @@ -29,6 +27,6 @@ esdhc@70008000 { compatible = "fsl,imx51-esdhc"; reg = <0x70008000 0x4000>; interrupts = <2>; - cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */ - wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */ + cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */ }; diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt index d64aea5..0e5e2ec 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -1,8 +1,9 @@ MMC/SD/SDIO slot directly connected to a SPI bus +This file documents differences between the core properties described +by mmc.txt and the properties used by the mmc_spi driver. + Required properties: -- compatible : should be "mmc-spi-slot". -- reg : should specify SPI address (chip-select number). - spi-max-frequency : maximum frequency for this device (Hz). - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). @@ -11,8 +12,7 @@ Required properties: Optional properties: - gpios : may specify GPIOs in this order: Card-Detect GPIO, Write-Protect GPIO. Note that this does not follow the - binding from mmc.txt, for historic reasons. -- interrupts : the interrupt of a card detect interrupt. + binding from mmc.txt, for historical reasons. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 6e70dcd..8a6811f 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -2,13 +2,17 @@ These properties are common to multiple MMC host controllers. Any host that requires the respective functionality should implement them using these definitions. +Interpreted by the OF core: +- reg: Registers location and length. +- interrupts: Interrupts used by the MMC controller. + Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> Optional properties: -- cd-gpios : Specify GPIOs for card detection, see gpio binding -- wp-gpios : Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the wp gpio line is inverted +- cd-gpios: Specify GPIOs for card detection, see gpio binding +- wp-gpios: Specify GPIOs for write protection, see gpio binding +- cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 14a81d5..2b584ca 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -1,19 +1,15 @@ * ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1 -The ARM PrimeCell MMCI PL180 and PL181 provides and interface for +The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. +This file documents differences between the core properties described +by mmc.txt and the properties used by the mmci driver. + Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- reg : contains pl18x registers and length. -- interrupts : contains the device IRQ(s). - arm,primecell-periphid : contains the PrimeCell Peripheral ID. Optional properties: -- wp-gpios : contains any write protect (ro) gpios -- cd-gpios : contains any card detection gpios -- cd-inverted : indicates whether the cd gpio is inverted -- max-frequency : contains the maximum operating frequency -- bus-width : number of data lines, can be <1>, <4>, or <8> - mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable - mmc-cap-sd-highspeed : indicates whether SD is high speed capable diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt index 14d870a..54949f6 100644 --- a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt @@ -3,16 +3,14 @@ The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller to support MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties in mmc.txt +and the properties used by the mxsmmc driver. + Required properties: - compatible: Should be "fsl,<chip>-mmc". The supported chips include imx23 and imx28. -- reg: Should contain registers location and length - interrupts: Should contain ERROR and DMA interrupts - fsl,ssp-dma-channel: APBH DMA channel for the SSP -- bus-width: Number of data lines, can be <1>, <4>, or <8> - -Optional properties: -- wp-gpios: Specify GPIOs for write protection Examples: diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index f77c303..c6d7b11 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -3,15 +3,13 @@ This controller on Tegra family SoCs provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-tegra driver. + Required properties: - compatible : Should be "nvidia,<chip>-sdhci" -- reg : Should contain SD/MMC registers location and length -- interrupts : Should contain SD/MMC interrupt -- bus-width : Number of data lines, can be <1>, <4>, or <8> Optional properties: -- cd-gpios : Specify GPIOs for card detection -- wp-gpios : Specify GPIOs for write protection - power-gpios : Specify GPIOs for power control Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt new file mode 100644 index 0000000..dbe98a3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt @@ -0,0 +1,21 @@ +* Marvell sdhci-pxa v2/v3 controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +Required properties: +- compatible: Should be "mrvl,pxav2-mmc" or "mrvl,pxav3-mmc". + +Optional properties: +- mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning. + +Example: + +sdhci@d4280800 { + compatible = "mrvl,pxav3-mmc"; + reg = <0xd4280800 0x800>; + bus-width = <8>; + interrupts = <27>; + non-removable; + mrvl,clk-delay-cycles = <31>; +}; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 8a53958..be76a23 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -3,21 +3,20 @@ The Highspeed MMC Host Controller on TI OMAP family provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap_hsmmc driver. + Required properties: - compatible: Should be "ti,omap2-hsmmc", for OMAP2 controllers Should be "ti,omap3-hsmmc", for OMAP3 controllers Should be "ti,omap4-hsmmc", for OMAP4 controllers - ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 -- reg : should contain hsmmc registers location and length Optional properties: ti,dual-volt: boolean, supports dual voltage cards <supply-name>-supply: phandle to the regulator device tree node "supply-name" examples are "vmmc", "vmmc_aux" etc -bus-width: Number of data lines, default assumed is 1 if the property is missing. -cd-gpios: GPIOs for card detection -wp-gpios: GPIOs for write protection ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence diff --git a/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt new file mode 100644 index 0000000..7c86d5e --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt @@ -0,0 +1,29 @@ +The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs. They +have these bindings in addition to the standard PHY bindings. + +Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and + "ethernet-phy-ieee802.3-c45" + +Optional Properties: + +- broadcom,c45-reg-init : one of more sets of 4 cells. The first cell + is the MDIO Manageable Device (MMD) address, the second a register + address within the MMD, the third cell contains a mask to be ANDed + with the existing register value, and the fourth cell is ORed with + he result to yield the new register value. If the third cell has a + value of zero, no read of the existing value is performed. + +Example: + + ethernet-phy@5 { + reg = <5>; + compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45"; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + /* + * Set PMD Digital Control Register for + * GPIO[1] Tx/Rx + * GPIO[0] R64 Sync Acquired + */ + broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>; + }; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index f31b686..8ff324e 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -11,6 +11,9 @@ Required properties: - reg : Offset and length of the register set for this device - interrupts : Interrupt tuple for this device + +Optional properties: + - clock-frequency : The oscillator frequency driving the flexcan device Example: diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt new file mode 100644 index 0000000..48b259e --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -0,0 +1,41 @@ +* Texas Instruments Davinci EMAC + +This file provides information, what the device node +for the davinci_emac interface contains. + +Required properties: +- compatible: "ti,davinci-dm6467-emac"; +- reg: Offset and length of the register set for the device +- ti,davinci-ctrl-reg-offset: offset to control register +- ti,davinci-ctrl-mod-reg-offset: offset to control module register +- ti,davinci-ctrl-ram-offset: offset to control module ram +- ti,davinci-ctrl-ram-size: size of control module ram +- ti,davinci-rmii-en: use RMII +- ti,davinci-no-bd-ram: has the emac controller BD RAM +- phy-handle: Contains a phandle to an Ethernet PHY. + if not, davinci_emac driver defaults to 100/FULL +- interrupts: interrupt mapping for the davinci emac interrupts sources: + 4 sources: <Receive Threshold Interrupt + Receive Interrupt + Transmit Interrupt + Miscellaneous Interrupt> + +Optional properties: +- local-mac-address : 6 bytes, mac address + +Example (enbw_cmc board): + eth0: emac@1e20000 { + compatible = "ti,davinci-dm6467-emac"; + reg = <0x220000 0x4000>; + ti,davinci-ctrl-reg-offset = <0x3000>; + ti,davinci-ctrl-mod-reg-offset = <0x2000>; + ti,davinci-ctrl-ram-offset = <0>; + ti,davinci-ctrl-ram-size = <0x2000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <33 + 34 + 35 + 36 + >; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 7ab9e1a..d536392 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -7,10 +7,14 @@ Required properties: - phy-mode : String, operation mode of the PHY interface. Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii", "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii". -- phy-reset-gpios : Should specify the gpio for phy reset Optional properties: - local-mac-address : 6 bytes, mac address +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. Example: @@ -19,6 +23,6 @@ ethernet@83fec000 { reg = <0x83fec000 0x4000>; interrupts = <87>; phy-mode = "mii"; - phy-reset-gpios = <&gpio1 14 0>; /* GPIO2_14 */ + phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ local-mac-address = [00 04 9F 01 1B B9]; }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index bb8c742..7cd18fb 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -14,10 +14,20 @@ Required properties: - linux,phandle : phandle for this node; likely referenced by an ethernet controller node. +Optional Properties: + +- compatible: Compatible list, may contain + "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for + PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 + specifications. If neither of these are specified, the default is to + assume clause 22. The compatible list may also contain other + elements. + Example: ethernet-phy@0 { - linux,phandle = <2452000> + compatible = "ethernet-phy-ieee802.3-c22"; + linux,phandle = <2452000>; interrupt-parent = <40000>; interrupts = <35 1>; reg = <0>; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 1f62623..060bbf0 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -1,7 +1,8 @@ * STMicroelectronics 10/100/1000 Ethernet driver (GMAC) Required properties: -- compatible: Should be "st,spear600-gmac" +- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac" + For backwards compatibility: "st,spear600-gmac" is also supported. - reg: Address and length of the register set for the device - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device diff --git a/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt index 5aeee53..5aeee53 100644 --- a/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt +++ b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt index 82b43f9..a4119f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt @@ -1626,3 +1626,5 @@ MX6Q_PAD_SD2_DAT3__PCIE_CTRL_MUX_11 1587 MX6Q_PAD_SD2_DAT3__GPIO_1_12 1588 MX6Q_PAD_SD2_DAT3__SJC_DONE 1589 MX6Q_PAD_SD2_DAT3__ANATOP_TESTO_3 1590 +MX6Q_PAD_ENET_RX_ER__ANATOP_USBOTG_ID 1591 +MX6Q_PAD_GPIO_1__ANATOP_USBOTG_ID 1592 diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt index 2f5b6b1..4fae41d 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -10,6 +10,7 @@ Optional properties: If this property is missing, the default assumed is Active low. - gpio-open-drain: GPIO is open drain type. If this property is missing then default assumption is false. +-vin-supply: Input supply name. Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -29,4 +30,5 @@ Example: enable-active-high; regulator-boot-on; gpio-open-drain; + vin-supply = <&parent_reg>; }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 5b7a408..66ece3f 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -10,6 +10,11 @@ Optional properties: - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator - <name>-supply: phandle to the parent supply/regulator node +- regulator-ramp-delay: ramp delay for regulator(in uV/uS) +- regulator-compatible: If a regulator chip contains multiple + regulators, and if the chip's binding contains a child node that + describes each regulator, then this property indicates which regulator + this child node is intended to configure. Example: diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt new file mode 100644 index 0000000..0487e96 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -0,0 +1,91 @@ +TPS65217 family of regulators + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-3] and ldo[1-4] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + compatible = "ti,tps65217"; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-compatible = "dcdc1"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + regulator-compatible = "dcdc2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + regulator-compatible = "dcdc3"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index 0fcabaa..d156e1b 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -6,8 +6,17 @@ Required properties: - interrupts: the interrupt outputs of the controller - #gpio-cells: number of cells to describe a GPIO - gpio-controller: mark the device as a GPIO controller -- regulators: list of regulators provided by this controller, must be named - after their hardware counterparts: sm[0-2], ldo[0-9] and ldo_rtc +- regulators: list of regulators provided by this controller, must have + property "regulator-compatible" to match their hardware counterparts: + sm[0-2], ldo[0-9] and ldo_rtc +- sm0-supply: The input supply for the SM0. +- sm1-supply: The input supply for the SM1. +- sm2-supply: The input supply for the SM2. +- vinldo01-supply: The input supply for the LDO1 and LDO2 +- vinldo23-supply: The input supply for the LDO2 and LDO3 +- vinldo4-supply: The input supply for the LDO4 +- vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8 +- vinldo9-supply: The input supply for the LDO9 Each regulator is defined using the standard binding for regulators. @@ -21,75 +30,113 @@ Example: #gpio-cells = <2>; gpio-controller; + sm0-supply = <&some_reg>; + sm1-supply = <&some_reg>; + sm2-supply = <&some_reg>; + vinldo01-supply = <...>; + vinldo23-supply = <...>; + vinldo4-supply = <...>; + vinldo678-supply = <...>; + vinldo9-supply = <...>; + regulators { - sm0_reg: sm0 { + #address-cells = <1>; + #size-cells = <0>; + + sm0_reg: regulator@0 { + reg = <0>; + regulator-compatible = "sm0"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm1_reg: sm1 { + sm1_reg: regulator@1 { + reg = <1>; + regulator-compatible = "sm1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm2_reg: sm2 { + sm2_reg: regulator@2 { + reg = <2>; + regulator-compatible = "sm2"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <4550000>; regulator-boot-on; regulator-always-on; }; - ldo0_reg: ldo0 { + ldo0_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo0"; regulator-name = "PCIE CLK"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo2"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo3"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + reg = <7>; + regulator-compatible = "ldo4"; regulator-min-microvolt = <1700000>; regulator-max-microvolt = <2475000>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + reg = <8>; + regulator-compatible = "ldo5"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + reg = <9>; + regulator-compatible = "ldo6"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + reg = <10>; + regulator-compatible = "ldo7"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + reg = <11>; + regulator-compatible = "ldo8"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo9_reg: ldo9 { + ldo9_reg: regulator@12 { + reg = <12>; + regulator-compatible = "ldo9"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 0c3395d..658749b 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -15,7 +15,6 @@ For twl6030 regulators/LDOs - "ti,twl6030-vusb" for VUSB LDO - "ti,twl6030-v1v8" for V1V8 LDO - "ti,twl6030-v2v1" for V2V1 LDO - - "ti,twl6030-clk32kg" for CLK32KG RESOURCE - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS diff --git a/Documentation/devicetree/bindings/rtc/dw-apb.txt b/Documentation/devicetree/bindings/rtc/dw-apb.txt new file mode 100644 index 0000000..93e2b0f --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/dw-apb.txt @@ -0,0 +1,25 @@ +* Designware APB timer + +Required properties: +- compatible: "snps,dw-apb-timer-sp" or "snps,dw-apb-timer-osc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: IRQ line for the timer. +- clock-frequency: The frequency in HZ of the timer. +- clock-freq: For backwards compatibility with picoxcell + +Example: + + timer1: timer@ffc09000 { + compatible = "snps,dw-apb-timer-sp"; + interrupts = <0 168 4>; + clock-frequency = <200000000>; + reg = <0xffc09000 0x1000>; + }; + + timer2: timer@ffd00000 { + compatible = "snps,dw-apb-timer-osc"; + interrupts = <0 169 4>; + clock-frequency = <200000000>; + reg = <0xffd00000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt b/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt new file mode 100644 index 0000000..b800070 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt @@ -0,0 +1,16 @@ +* STMP3xxx/i.MX28 Time Clock controller + +Required properties: +- compatible: should be one of the following. + * "fsl,stmp3xxx-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + +rtc@80056000 { + compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc"; + reg = <0x80056000 2000>; + interrupts = <29>; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt index b77a97c..b77a97c 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-trimslice.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt index 04b14cf..04b14cf 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-trimslice.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-wm8753.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt index c4dd39c..c4dd39c 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-wm8753.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt index d5b0da8..d5b0da8 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt diff --git a/Documentation/devicetree/bindings/sound/tegra20-das.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt index 6de3a7e..6de3a7e 100644 --- a/Documentation/devicetree/bindings/sound/tegra20-das.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt diff --git a/Documentation/devicetree/bindings/sound/tegra20-i2s.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt index 0df2b5c..0df2b5c 100644 --- a/Documentation/devicetree/bindings/sound/tegra20-i2s.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 9841057..4256a6d 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -17,6 +17,6 @@ ecspi@70010000 { reg = <0x70010000 0x4000>; interrupts = <36>; fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ - <&gpio3 25 0>; /* GPIO4_25 */ + cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ + <&gpio3 25 0>; /* GPIO3_25 */ }; diff --git a/Documentation/devicetree/bindings/spi/spi_nvidia.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-spi.txt index 6b9e518..6b9e518 100644 --- a/Documentation/devicetree/bindings/spi/spi_nvidia.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-spi.txt diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt new file mode 100644 index 0000000..a15ffed --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -0,0 +1,116 @@ +* Samsung SPI Controller + +The Samsung SPI controller is used to interface with various devices such as flash +and display controllers using the SPI communication interface. + +Required SoC Specific Properties: + +- compatible: should be one of the following. + - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms + - samsung,s3c6410-spi: for s3c6410 platforms + - samsung,s5p6440-spi: for s5p6440 and s5p6450 platforms + - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms + - samsung,exynos4210-spi: for exynos4 and exynos5 platforms + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. + +[PRELIMINARY: the dma channel allocation will change once there are +official DMA bindings] + +- tx-dma-channel: The dma channel specifier for tx operations. The format of + the dma specifier depends on the dma controller. + +- rx-dma-channel: The dma channel specifier for rx operations. The format of + the dma specifier depends on the dma controller. + +Required Board Specific Properties: + +- #address-cells: should be 1. +- #size-cells: should be 0. +- gpios: The gpio specifier for clock, mosi and miso interface lines (in the + order specified). The format of the gpio specifier depends on the gpio + controller. + +Optional Board Specific Properties: + +- samsung,spi-src-clk: If the spi controller includes a internal clock mux to + select the clock source for the spi bus clock, this property can be used to + indicate the clock to be used for driving the spi bus clock. If not specified, + the clock number 0 is used as default. + +- num-cs: Specifies the number of chip select lines supported. If + not specified, the default number of chip select lines is set to 1. + +SPI Controller specific data in SPI slave nodes: + +- The spi slave nodes should provide the following information which is required + by the spi controller. + + - cs-gpio: A gpio specifier that specifies the gpio line used as + the slave select line by the spi controller. The format of the gpio + specifier depends on the gpio controller. + + - samsung,spi-feedback-delay: The sampling phase shift to be applied on the + miso line (to account for any lag in the miso line). The following are the + valid values. + + - 0: No phase shift. + - 1: 90 degree phase shift sampling. + - 2: 180 degree phase shift sampling. + - 3: 270 degree phase shift sampling. + +Aliases: + +- All the SPI controller nodes should be represented in the aliases node using + the following format 'spi{n}' where n is a unique number for the alias. + + +Example: + +- SoC Specific Portion: + + spi_0: spi@12d20000 { + compatible = "samsung,exynos4210-spi"; + reg = <0x12d20000 0x100>; + interrupts = <0 66 0>; + tx-dma-channel = <&pdma0 5>; + rx-dma-channel = <&pdma0 4>; + }; + +- Board Specific Portion: + + spi_0: spi@12d20000 { + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpa2 4 2 3 0>, + <&gpa2 6 2 3 0>, + <&gpa2 7 2 3 0>; + + w25q80bw@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "w25x80"; + reg = <0>; + spi-max-frequency = <10000>; + + controller-data { + cs-gpio = <&gpa2 5 1 0 3>; + samsung,spi-feedback-delay = <0>; + }; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "Kernel"; + reg = <0x40000 0xc0000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt new file mode 100644 index 0000000..2ee903f --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -0,0 +1,27 @@ +* Freescale MXS Application UART (AUART) + +Required properties: +- compatible : Should be "fsl,<soc>-auart". The supported SoCs include + imx23 and imx28. +- reg : Address and length of the register set for the device +- interrupts : Should contain the auart interrupt numbers + +Example: +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112 70 71>; +}; + +Note: Each auart port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + serial0 = &auart0; + serial1 = &auart1; + serial2 = &auart2; + serial3 = &auart3; + serial4 = &auart4; +}; diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index e9b005d..e9b005d 100644 --- a/Documentation/devicetree/bindings/usb/tegra-usb.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 6eab917..db4d3af 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -3,6 +3,7 @@ Device tree binding vendor prefix registry. Keep list in alphabetical order. This isn't an exhaustive list, but you should add new prefixes to it before using them to avoid name-space collisions. +ad Avionic Design GmbH adi Analog Devices, Inc. amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) diff --git a/Documentation/devicetree/bindings/watchdog/omap-wdt.txt b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt new file mode 100644 index 0000000..c227970 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt @@ -0,0 +1,14 @@ +TI Watchdog Timer (WDT) Controller for OMAP + +Required properties: +compatible: +- "ti,omap3-wdt" for OMAP3 +- "ti,omap4-wdt" for OMAP4 +- ti,hwmods: Name of the hwmod associated to the WDT + +Examples: + +wdt2: wdt@4a314000 { + compatible = "ti,omap4-wdt", "ti,omap3-wdt"; + ti,hwmods = "wd_timer2"; +}; diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 56000b3..61d1a89 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -249,15 +249,6 @@ Who: Ravikiran Thirumalai <kiran@scalex86.org> --------------------------- -What: Code that is now under CONFIG_WIRELESS_EXT_SYSFS - (in net/core/net-sysfs.c) -When: 3.5 -Why: Over 1K .text/.data size reduction, data is available in other - ways (ioctls) -Who: Johannes Berg <johannes@sipsolutions.net> - ---------------------------- - What: sysfs ui for changing p4-clockmod parameters When: September 2009 Why: See commits 129f8ae9b1b5be94517da76009ea956e89104ce8 and @@ -414,21 +405,6 @@ Who: Jean Delvare <khali@linux-fr.org> ---------------------------- -What: xt_connlimit rev 0 -When: 2012 -Who: Jan Engelhardt <jengelh@medozas.de> -Files: net/netfilter/xt_connlimit.c - ----------------------------- - -What: ipt_addrtype match include file -When: 2012 -Why: superseded by xt_addrtype -Who: Florian Westphal <fw@strlen.de> -Files: include/linux/netfilter_ipv4/ipt_addrtype.h - ----------------------------- - What: i2c_driver.attach_adapter i2c_driver.detach_adapter When: September 2011 @@ -449,6 +425,19 @@ Who: Hans Verkuil <hans.verkuil@cisco.com> ---------------------------- +What: CONFIG_CFG80211_WEXT +When: as soon as distributions ship new wireless tools, ie. wpa_supplicant 1.0 + and NetworkManager/connman/etc. that are able to use nl80211 +Why: Wireless extensions are deprecated, and userland tools are moving to + using nl80211. New drivers are no longer using wireless extensions, + and while there might still be old drivers, both new drivers and new + userland no longer needs them and they can't be used for an feature + developed in the past couple of years. As such, compatibility with + wireless extensions in new drivers will be removed. +Who: Johannes Berg <johannes@sipsolutions.net> + +---------------------------- + What: g_file_storage driver When: 3.8 Why: This driver has been superseded by g_mass_storage. @@ -589,6 +578,13 @@ Why: Remount currently allows changing bound subsystems and ---------------------------- +What: xt_recent rev 0 +When: 2013 +Who: Pablo Neira Ayuso <pablo@netfilter.org> +Files: net/netfilter/xt_recent.c + +---------------------------- + What: KVM debugfs statistics When: 2013 Why: KVM tracepoints provide mostly equivalent information in a much more diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index 8e2da1e..e0cce2a 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -9,7 +9,7 @@ be able to use diff(1). --------------------------- dentry_operations -------------------------- prototypes: - int (*d_revalidate)(struct dentry *, struct nameidata *); + int (*d_revalidate)(struct dentry *, unsigned int); int (*d_hash)(const struct dentry *, const struct inode *, struct qstr *); int (*d_compare)(const struct dentry *, const struct inode *, @@ -37,9 +37,8 @@ d_manage: no no yes (ref-walk) maybe --------------------------- inode_operations --------------------------- prototypes: - int (*create) (struct inode *,struct dentry *,umode_t, struct nameidata *); - struct dentry * (*lookup) (struct inode *,struct dentry *, struct nameid -ata *); + int (*create) (struct inode *,struct dentry *,umode_t, bool); + struct dentry * (*lookup) (struct inode *,struct dentry *, unsigned int); int (*link) (struct dentry *,struct inode *,struct dentry *); int (*unlink) (struct inode *,struct dentry *); int (*symlink) (struct inode *,struct dentry *,const char *); @@ -62,6 +61,9 @@ ata *); int (*removexattr) (struct dentry *, const char *); int (*fiemap)(struct inode *, struct fiemap_extent_info *, u64 start, u64 len); void (*update_time)(struct inode *, struct timespec *, int); + int (*atomic_open)(struct inode *, struct dentry *, + struct file *, unsigned open_flag, + umode_t create_mode, int *opened); locking rules: all may block @@ -89,6 +91,7 @@ listxattr: no removexattr: yes fiemap: no update_time: no +atomic_open: yes Additionally, ->rmdir(), ->unlink() and ->rename() have ->i_mutex on victim. diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting index 8c91d10..2bef2b3 100644 --- a/Documentation/filesystems/porting +++ b/Documentation/filesystems/porting @@ -355,12 +355,10 @@ protects *all* the dcache state of a given dentry. via rcu-walk path walk (basically, if the file can have had a path name in the vfs namespace). - i_dentry and i_rcu share storage in a union, and the vfs expects -i_dentry to be reinitialized before it is freed, so an: - - INIT_LIST_HEAD(&inode->i_dentry); - -must be done in the RCU callback. + Even though i_dentry and i_rcu share storage in a union, we will +initialize the former in inode_init_always(), so just leave it alone in +the callback. It used to be necessary to clean it there, but not anymore +(starting at 3.2). -- [recommended] @@ -433,3 +431,14 @@ release it yourself. d_alloc_root() is gone, along with a lot of bugs caused by code misusing it. Replacement: d_make_root(inode). The difference is, d_make_root() drops the reference to inode if dentry allocation fails. + +-- +[mandatory] + The witch is dead! Well, 2/3 of it, anyway. ->d_revalidate() and +->lookup() do *not* take struct nameidata anymore; just the flags. +-- +[mandatory] + ->create() doesn't take struct nameidata *; unlike the previous +two, it gets "is it an O_EXCL or equivalent?" boolean argument. Note that +local filesystems can ignore tha argument - they are guaranteed that the +object doesn't exist. It's remote/distributed ones that might care... diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index efd23f4..aa754e0 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -341,8 +341,8 @@ This describes how the VFS can manipulate an inode in your filesystem. As of kernel 2.6.22, the following members are defined: struct inode_operations { - int (*create) (struct inode *,struct dentry *, umode_t, struct nameidata *); - struct dentry * (*lookup) (struct inode *,struct dentry *, struct nameidata *); + int (*create) (struct inode *,struct dentry *, umode_t, bool); + struct dentry * (*lookup) (struct inode *,struct dentry *, unsigned int); int (*link) (struct dentry *,struct inode *,struct dentry *); int (*unlink) (struct inode *,struct dentry *); int (*symlink) (struct inode *,struct dentry *,const char *); @@ -364,6 +364,9 @@ struct inode_operations { ssize_t (*listxattr) (struct dentry *, char *, size_t); int (*removexattr) (struct dentry *, const char *); void (*update_time)(struct inode *, struct timespec *, int); + int (*atomic_open)(struct inode *, struct dentry *, + struct file *, unsigned open_flag, + umode_t create_mode, int *opened); }; Again, all methods are called without any locks being held, unless @@ -476,6 +479,14 @@ otherwise noted. an inode. If this is not defined the VFS will update the inode itself and call mark_inode_dirty_sync. + atomic_open: called on the last component of an open. Using this optional + method the filesystem can look up, possibly create and open the file in + one atomic operation. If it cannot perform this (e.g. the file type + turned out to be wrong) it may signal this by returning 1 instead of + usual 0 or -ve . This method is only called if the last + component is negative or needs lookup. Cached positive dentries are + still handled by f_op->open(). + The Address Space Object ======================== @@ -891,7 +902,7 @@ the VFS uses a default. As of kernel 2.6.22, the following members are defined: struct dentry_operations { - int (*d_revalidate)(struct dentry *, struct nameidata *); + int (*d_revalidate)(struct dentry *, unsigned int); int (*d_hash)(const struct dentry *, const struct inode *, struct qstr *); int (*d_compare)(const struct dentry *, const struct inode *, @@ -910,11 +921,11 @@ struct dentry_operations { dcache. Most filesystems leave this as NULL, because all their dentries in the dcache are valid - d_revalidate may be called in rcu-walk mode (nd->flags & LOOKUP_RCU). + d_revalidate may be called in rcu-walk mode (flags & LOOKUP_RCU). If in rcu-walk mode, the filesystem must revalidate the dentry without blocking or storing to the dentry, d_parent and d_inode should not be - used without care (because they can go NULL), instead nd->inode should - be used. + used without care (because they can change and, in d_inode case, even + become NULL under us). If a situation is encountered that rcu-walk cannot handle, return -ECHILD and it will be called again in ref-walk mode. diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp index 84d46c0..c86b50c 100644 --- a/Documentation/hwmon/coretemp +++ b/Documentation/hwmon/coretemp @@ -6,7 +6,9 @@ Supported chips: Prefix: 'coretemp' CPUID: family 0x6, models 0xe (Pentium M DC), 0xf (Core 2 DC 65nm), 0x16 (Core 2 SC 65nm), 0x17 (Penryn 45nm), - 0x1a (Nehalem), 0x1c (Atom), 0x1e (Lynnfield) + 0x1a (Nehalem), 0x1c (Atom), 0x1e (Lynnfield), + 0x26 (Tunnel Creek Atom), 0x27 (Medfield Atom), + 0x36 (Cedar Trail Atom) Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual Volume 3A: System Programming Guide http://softwarecommunity.intel.com/Wiki/Mobility/720.htm @@ -52,6 +54,17 @@ Some information comes from ark.intel.com Process Processor TjMax(C) +22nm Core i5/i7 Processors + i7 3920XM, 3820QM, 3720QM, 3667U, 3520M 105 + i5 3427U, 3360M/3320M 105 + i7 3770/3770K 105 + i5 3570/3570K, 3550, 3470/3450 105 + i7 3770S 103 + i5 3570S/3550S, 3475S/3470S/3450S 103 + i7 3770T 94 + i5 3570T 94 + i5 3470T 91 + 32nm Core i3/i5/i7 Processors i7 660UM/640/620, 640LM/620, 620M, 610E 105 i5 540UM/520/430, 540M/520/450/430 105 @@ -65,6 +78,11 @@ Process Processor TjMax(C) U3400 105 P4505/P4500 90 +32nm Atom Processors + Z2460 90 + D2700/2550/2500 100 + N2850/2800/2650/2600 100 + 45nm Xeon Processors 5400 Quad-Core X5492, X5482, X5472, X5470, X5460, X5450 85 E5472, E5462, E5450/40/30/20/10/05 85 @@ -85,6 +103,8 @@ Process Processor TjMax(C) N475/470/455/450 100 N280/270 90 330/230 125 + E680/660/640/620 90 + E680T/660T/640T/620T 110 45nm Core2 Processors Solo ULV SU3500/3300 100 diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt index 506c739..13f1aa0 100644 --- a/Documentation/kdump/kdump.txt +++ b/Documentation/kdump/kdump.txt @@ -86,7 +86,7 @@ There is also a gitweb interface available at http://www.kernel.org/git/?p=utils/kernel/kexec/kexec-tools.git More information about kexec-tools can be found at -http://www.kernel.org/pub/linux/utils/kernel/kexec/README.html +http://horms.net/projects/kexec/ 3) Unpack the tarball with the tar command, as follows: diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index a92c5eb..12783fa 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2367,6 +2367,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted. Set maximum number of finished RCU callbacks to process in one batch. + rcutree.fanout_leaf= [KNL,BOOT] + Increase the number of CPUs assigned to each + leaf rcu_node structure. Useful for very large + systems. + rcutree.qhimark= [KNL,BOOT] Set threshold of queued RCU callbacks over which batch limiting is disabled. diff --git a/Documentation/networking/batman-adv.txt b/Documentation/networking/batman-adv.txt index 75a5923..8f3ae4a 100644 --- a/Documentation/networking/batman-adv.txt +++ b/Documentation/networking/batman-adv.txt @@ -211,6 +211,11 @@ The debug output can be changed at runtime using the file will enable debug messages for when routes change. +Counters for different types of packets entering and leaving the +batman-adv module are available through ethtool: + +# ethtool --statistics bat0 + BATCTL ------ diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index bfea8a3..6b1c711 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -1210,7 +1210,7 @@ options, you may wish to use the "max_bonds" module parameter, documented above. To create multiple bonding devices with differing options, it is -preferrable to use bonding parameters exported by sysfs, documented in the +preferable to use bonding parameters exported by sysfs, documented in the section below. For versions of bonding without sysfs support, the only means to @@ -1950,7 +1950,7 @@ access to fail over to. Additionally, the bonding load balance modes support link monitoring of their members, so if individual links fail, the load will be rebalanced across the remaining devices. - See Section 13, "Configuring Bonding for Maximum Throughput" + See Section 12, "Configuring Bonding for Maximum Throughput" for information on configuring bonding with one peer device. 11.2 High Availability in a Multiple Switch Topology @@ -2620,7 +2620,7 @@ be found at: https://lists.sourceforge.net/lists/listinfo/bonding-devel - Discussions regarding the developpement of the bonding driver take place + Discussions regarding the development of the bonding driver take place on the main Linux network mailing list, hosted at vger.kernel.org. The list address is: diff --git a/Documentation/networking/bridge.txt b/Documentation/networking/bridge.txt index a7ba5e4..a27cb62 100644 --- a/Documentation/networking/bridge.txt +++ b/Documentation/networking/bridge.txt @@ -1,7 +1,14 @@ In order to use the Ethernet bridging functionality, you'll need the -userspace tools. These programs and documentation are available -at http://www.linuxfoundation.org/en/Net:Bridge. The download page is -http://prdownloads.sourceforge.net/bridge. +userspace tools. + +Documentation for Linux bridging is on: + http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge + +The bridge-utilities are maintained at: + git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/bridge-utils.git + +Additionally, the iproute2 utilities can be used to configure +bridge devices. If you still have questions, don't hesitate to post to the mailing list (more info https://lists.linux-foundation.org/mailman/listinfo/bridge). diff --git a/Documentation/networking/caif/Linux-CAIF.txt b/Documentation/networking/caif/Linux-CAIF.txt index e52fd62..0aa4bd3 100644 --- a/Documentation/networking/caif/Linux-CAIF.txt +++ b/Documentation/networking/caif/Linux-CAIF.txt @@ -19,60 +19,36 @@ and host. Currently, UART and Loopback are available for Linux. Architecture: ------------ The implementation of CAIF is divided into: -* CAIF Socket Layer, Kernel API, and Net Device. +* CAIF Socket Layer and GPRS IP Interface. * CAIF Core Protocol Implementation * CAIF Link Layer, implemented as NET devices. RTNL ! - ! +------+ +------+ +------+ - ! +------+! +------+! +------+! - ! ! Sock !! !Kernel!! ! Net !! - ! ! API !+ ! API !+ ! Dev !+ <- CAIF Client APIs - ! +------+ +------! +------+ - ! ! ! ! - ! +----------!----------+ - ! +------+ <- CAIF Protocol Implementation - +-------> ! CAIF ! - ! Core ! - +------+ - +--------!--------+ - ! ! - +------+ +-----+ - ! ! ! TTY ! <- Link Layer (Net Devices) - +------+ +-----+ - - -Using the Kernel API ----------------------- -The Kernel API is used for accessing CAIF channels from the -kernel. -The user of the API has to implement two callbacks for receive -and control. -The receive callback gives a CAIF packet as a SKB. The control -callback will -notify of channel initialization complete, and flow-on/flow- -off. - - - struct caif_device caif_dev = { - .caif_config = { - .name = "MYDEV" - .type = CAIF_CHTY_AT - } - .receive_cb = my_receive, - .control_cb = my_control, - }; - caif_add_device(&caif_dev); - caif_transmit(&caif_dev, skb); - -See the caif_kernel.h for details about the CAIF kernel API. + ! +------+ +------+ + ! +------+! +------+! + ! ! IP !! !Socket!! + +-------> !interf!+ ! API !+ <- CAIF Client APIs + ! +------+ +------! + ! ! ! + ! +-----------+ + ! ! + ! +------+ <- CAIF Core Protocol + ! ! CAIF ! + ! ! Core ! + ! +------+ + ! +----------!---------+ + ! ! ! ! + ! +------+ +-----+ +------+ + +--> ! HSI ! ! TTY ! ! USB ! <- Link Layer (Net Devices) + +------+ +-----+ +------+ + I M P L E M E N T A T I O N =========================== -=========================== + CAIF Core Protocol Layer ========================================= @@ -88,17 +64,13 @@ The Core CAIF implementation contains: - Simple implementation of CAIF. - Layered architecture (a la Streams), each layer in the CAIF specification is implemented in a separate c-file. - - Clients must implement PHY layer to access physical HW - with receive and transmit functions. - Clients must call configuration function to add PHY layer. - Clients must implement CAIF layer to consume/produce CAIF payload with receive and transmit functions. - Clients must call configuration function to add and connect the Client layer. - When receiving / transmitting CAIF Packets (cfpkt), ownership is passed - to the called function (except for framing layers' receive functions - or if a transmit function returns an error, in which case the caller - must free the packet). + to the called function (except for framing layers' receive function) Layered Architecture -------------------- @@ -109,11 +81,6 @@ Implementation. The support functions include: CAIF Packet has functions for creating, destroying and adding content and for adding/extracting header and trailers to protocol packets. - - CFLST CAIF list implementation. - - - CFGLUE CAIF Glue. Contains OS Specifics, such as memory - allocation, endianness, etc. - The CAIF Protocol implementation contains: - CFCNFG CAIF Configuration layer. Configures the CAIF Protocol @@ -128,7 +95,7 @@ The CAIF Protocol implementation contains: control and remote shutdown requests. - CFVEI CAIF VEI layer. Handles CAIF AT Channels on VEI (Virtual - External Interface). This layer encodes/decodes VEI frames. + External Interface). This layer encodes/decodes VEI frames. - CFDGML CAIF Datagram layer. Handles CAIF Datagram layer (IP traffic), encodes/decodes Datagram frames. @@ -170,7 +137,7 @@ The CAIF Protocol implementation contains: +---------+ +---------+ ! ! +---------+ +---------+ - | | | Serial | + | | | Serial | | | | CFSERL | +---------+ +---------+ @@ -186,24 +153,20 @@ In this layered approach the following "rules" apply. layer->dn->transmit(layer->dn, packet); -Linux Driver Implementation +CAIF Socket and IP interface =========================== -Linux GPRS Net Device and CAIF socket are implemented on top of the -CAIF Core protocol. The Net device and CAIF socket have an instance of +The IP interface and CAIF socket API are implemented on top of the +CAIF Core protocol. The IP Interface and CAIF socket have an instance of 'struct cflayer', just like the CAIF Core protocol stack. Net device and Socket implement the 'receive()' function defined by 'struct cflayer', just like the rest of the CAIF stack. In this way, transmit and receive of packets is handled as by the rest of the layers: the 'dn->transmit()' function is called in order to transmit data. -The layer on top of the CAIF Core implementation is -sometimes referred to as the "Client layer". - - Configuration of Link Layer --------------------------- -The Link Layer is implemented as Linux net devices (struct net_device). +The Link Layer is implemented as Linux network devices (struct net_device). Payload handling and registration is done using standard Linux mechanisms. The CAIF Protocol relies on a loss-less link layer without implementing diff --git a/Documentation/networking/can.txt b/Documentation/networking/can.txt index ac29539..820f553 100644 --- a/Documentation/networking/can.txt +++ b/Documentation/networking/can.txt @@ -22,7 +22,8 @@ This file contains 4.1.2 RAW socket option CAN_RAW_ERR_FILTER 4.1.3 RAW socket option CAN_RAW_LOOPBACK 4.1.4 RAW socket option CAN_RAW_RECV_OWN_MSGS - 4.1.5 RAW socket returned message flags + 4.1.5 RAW socket option CAN_RAW_FD_FRAMES + 4.1.6 RAW socket returned message flags 4.2 Broadcast Manager protocol sockets (SOCK_DGRAM) 4.3 connected transport protocols (SOCK_SEQPACKET) 4.4 unconnected transport protocols (SOCK_DGRAM) @@ -41,7 +42,8 @@ This file contains 6.5.1 Netlink interface to set/get devices properties 6.5.2 Setting the CAN bit-timing 6.5.3 Starting and stopping the CAN network device - 6.6 supported CAN hardware + 6.6 CAN FD (flexible data rate) driver support + 6.7 supported CAN hardware 7 Socket CAN resources @@ -232,16 +234,16 @@ solution for a couple of reasons: arbitration problems and error frames caused by the different ECUs. The occurrence of detected errors are important for diagnosis and have to be logged together with the exact timestamp. For this - reason the CAN interface driver can generate so called Error Frames - that can optionally be passed to the user application in the same - way as other CAN frames. Whenever an error on the physical layer + reason the CAN interface driver can generate so called Error Message + Frames that can optionally be passed to the user application in the + same way as other CAN frames. Whenever an error on the physical layer or the MAC layer is detected (e.g. by the CAN controller) the driver - creates an appropriate error frame. Error frames can be requested by - the user application using the common CAN filter mechanisms. Inside - this filter definition the (interested) type of errors may be - selected. The reception of error frames is disabled by default. - The format of the CAN error frame is briefly described in the Linux - header file "include/linux/can/error.h". + creates an appropriate error message frame. Error messages frames can + be requested by the user application using the common CAN filter + mechanisms. Inside this filter definition the (interested) type of + errors may be selected. The reception of error messages is disabled + by default. The format of the CAN error message frame is briefly + described in the Linux header file "include/linux/can/error.h". 4. How to use Socket CAN ------------------------ @@ -273,7 +275,7 @@ solution for a couple of reasons: struct can_frame { canid_t can_id; /* 32 bit CAN_ID + EFF/RTR/ERR flags */ - __u8 can_dlc; /* data length code: 0 .. 8 */ + __u8 can_dlc; /* frame payload length in byte (0 .. 8) */ __u8 data[8] __attribute__((aligned(8))); }; @@ -375,6 +377,51 @@ solution for a couple of reasons: nbytes = sendto(s, &frame, sizeof(struct can_frame), 0, (struct sockaddr*)&addr, sizeof(addr)); + Remark about CAN FD (flexible data rate) support: + + Generally the handling of CAN FD is very similar to the formerly described + examples. The new CAN FD capable CAN controllers support two different + bitrates for the arbitration phase and the payload phase of the CAN FD frame + and up to 64 bytes of payload. This extended payload length breaks all the + kernel interfaces (ABI) which heavily rely on the CAN frame with fixed eight + bytes of payload (struct can_frame) like the CAN_RAW socket. Therefore e.g. + the CAN_RAW socket supports a new socket option CAN_RAW_FD_FRAMES that + switches the socket into a mode that allows the handling of CAN FD frames + and (legacy) CAN frames simultaneously (see section 4.1.5). + + The struct canfd_frame is defined in include/linux/can.h: + + struct canfd_frame { + canid_t can_id; /* 32 bit CAN_ID + EFF/RTR/ERR flags */ + __u8 len; /* frame payload length in byte (0 .. 64) */ + __u8 flags; /* additional flags for CAN FD */ + __u8 __res0; /* reserved / padding */ + __u8 __res1; /* reserved / padding */ + __u8 data[64] __attribute__((aligned(8))); + }; + + The struct canfd_frame and the existing struct can_frame have the can_id, + the payload length and the payload data at the same offset inside their + structures. This allows to handle the different structures very similar. + When the content of a struct can_frame is copied into a struct canfd_frame + all structure elements can be used as-is - only the data[] becomes extended. + + When introducing the struct canfd_frame it turned out that the data length + code (DLC) of the struct can_frame was used as a length information as the + length and the DLC has a 1:1 mapping in the range of 0 .. 8. To preserve + the easy handling of the length information the canfd_frame.len element + contains a plain length value from 0 .. 64. So both canfd_frame.len and + can_frame.can_dlc are equal and contain a length information and no DLC. + For details about the distinction of CAN and CAN FD capable devices and + the mapping to the bus-relevant data length code (DLC), see chapter 6.6. + + The length of the two CAN(FD) frame structures define the maximum transfer + unit (MTU) of the CAN(FD) network interface and skbuff data length. Two + definitions are specified for CAN specific MTUs in include/linux/can.h : + + #define CAN_MTU (sizeof(struct can_frame)) == 16 => 'legacy' CAN frame + #define CANFD_MTU (sizeof(struct canfd_frame)) == 72 => CAN FD frame + 4.1 RAW protocol sockets with can_filters (SOCK_RAW) Using CAN_RAW sockets is extensively comparable to the commonly @@ -383,7 +430,7 @@ solution for a couple of reasons: defaults are set at RAW socket binding time: - The filters are set to exactly one filter receiving everything - - The socket only receives valid data frames (=> no error frames) + - The socket only receives valid data frames (=> no error message frames) - The loopback of sent CAN frames is enabled (see chapter 3.2) - The socket does not receive its own sent frames (in loopback mode) @@ -434,7 +481,7 @@ solution for a couple of reasons: 4.1.2 RAW socket option CAN_RAW_ERR_FILTER As described in chapter 3.4 the CAN interface driver can generate so - called Error Frames that can optionally be passed to the user + called Error Message Frames that can optionally be passed to the user application in the same way as other CAN frames. The possible errors are divided into different error classes that may be filtered using the appropriate error mask. To register for every possible @@ -472,7 +519,69 @@ solution for a couple of reasons: setsockopt(s, SOL_CAN_RAW, CAN_RAW_RECV_OWN_MSGS, &recv_own_msgs, sizeof(recv_own_msgs)); - 4.1.5 RAW socket returned message flags + 4.1.5 RAW socket option CAN_RAW_FD_FRAMES + + CAN FD support in CAN_RAW sockets can be enabled with a new socket option + CAN_RAW_FD_FRAMES which is off by default. When the new socket option is + not supported by the CAN_RAW socket (e.g. on older kernels), switching the + CAN_RAW_FD_FRAMES option returns the error -ENOPROTOOPT. + + Once CAN_RAW_FD_FRAMES is enabled the application can send both CAN frames + and CAN FD frames. OTOH the application has to handle CAN and CAN FD frames + when reading from the socket. + + CAN_RAW_FD_FRAMES enabled: CAN_MTU and CANFD_MTU are allowed + CAN_RAW_FD_FRAMES disabled: only CAN_MTU is allowed (default) + + Example: + [ remember: CANFD_MTU == sizeof(struct canfd_frame) ] + + struct canfd_frame cfd; + + nbytes = read(s, &cfd, CANFD_MTU); + + if (nbytes == CANFD_MTU) { + printf("got CAN FD frame with length %d\n", cfd.len); + /* cfd.flags contains valid data */ + } else if (nbytes == CAN_MTU) { + printf("got legacy CAN frame with length %d\n", cfd.len); + /* cfd.flags is undefined */ + } else { + fprintf(stderr, "read: invalid CAN(FD) frame\n"); + return 1; + } + + /* the content can be handled independently from the received MTU size */ + + printf("can_id: %X data length: %d data: ", cfd.can_id, cfd.len); + for (i = 0; i < cfd.len; i++) + printf("%02X ", cfd.data[i]); + + When reading with size CANFD_MTU only returns CAN_MTU bytes that have + been received from the socket a legacy CAN frame has been read into the + provided CAN FD structure. Note that the canfd_frame.flags data field is + not specified in the struct can_frame and therefore it is only valid in + CANFD_MTU sized CAN FD frames. + + As long as the payload length is <=8 the received CAN frames from CAN FD + capable CAN devices can be received and read by legacy sockets too. When + user-generated CAN FD frames have a payload length <=8 these can be send + by legacy CAN network interfaces too. Sending CAN FD frames with payload + length > 8 to a legacy CAN network interface returns an -EMSGSIZE error. + + Implementation hint for new CAN applications: + + To build a CAN FD aware application use struct canfd_frame as basic CAN + data structure for CAN_RAW based applications. When the application is + executed on an older Linux kernel and switching the CAN_RAW_FD_FRAMES + socket option returns an error: No problem. You'll get legacy CAN frames + or CAN FD frames and can process them the same way. + + When sending to CAN devices make sure that the device is capable to handle + CAN FD frames by checking if the device maximum transfer unit is CANFD_MTU. + The CAN device MTU can be retrieved e.g. with a SIOCGIFMTU ioctl() syscall. + + 4.1.6 RAW socket returned message flags When using recvmsg() call, the msg->msg_flags may contain following flags: @@ -527,7 +636,7 @@ solution for a couple of reasons: rcvlist_all - list for unfiltered entries (no filter operations) rcvlist_eff - list for single extended frame (EFF) entries - rcvlist_err - list for error frames masks + rcvlist_err - list for error message frames masks rcvlist_fil - list for mask/value filters rcvlist_inv - list for mask/value filters (inverse semantic) rcvlist_sff - list for single standard frame (SFF) entries @@ -573,10 +682,13 @@ solution for a couple of reasons: dev->type = ARPHRD_CAN; /* the netdevice hardware type */ dev->flags = IFF_NOARP; /* CAN has no arp */ - dev->mtu = sizeof(struct can_frame); + dev->mtu = CAN_MTU; /* sizeof(struct can_frame) -> legacy CAN interface */ - The struct can_frame is the payload of each socket buffer in the - protocol family PF_CAN. + or alternative, when the controller supports CAN with flexible data rate: + dev->mtu = CANFD_MTU; /* sizeof(struct canfd_frame) -> CAN FD interface */ + + The struct can_frame or struct canfd_frame is the payload of each socket + buffer (skbuff) in the protocol family PF_CAN. 6.2 local loopback of sent frames @@ -784,15 +896,41 @@ solution for a couple of reasons: $ ip link set canX type can restart-ms 100 Alternatively, the application may realize the "bus-off" condition - by monitoring CAN error frames and do a restart when appropriate with - the command: + by monitoring CAN error message frames and do a restart when + appropriate with the command: $ ip link set canX type can restart - Note that a restart will also create a CAN error frame (see also - chapter 3.4). + Note that a restart will also create a CAN error message frame (see + also chapter 3.4). + + 6.6 CAN FD (flexible data rate) driver support + + CAN FD capable CAN controllers support two different bitrates for the + arbitration phase and the payload phase of the CAN FD frame. Therefore a + second bittiming has to be specified in order to enable the CAN FD bitrate. + + Additionally CAN FD capable CAN controllers support up to 64 bytes of + payload. The representation of this length in can_frame.can_dlc and + canfd_frame.len for userspace applications and inside the Linux network + layer is a plain value from 0 .. 64 instead of the CAN 'data length code'. + The data length code was a 1:1 mapping to the payload length in the legacy + CAN frames anyway. The payload length to the bus-relevant DLC mapping is + only performed inside the CAN drivers, preferably with the helper + functions can_dlc2len() and can_len2dlc(). + + The CAN netdevice driver capabilities can be distinguished by the network + devices maximum transfer unit (MTU): + + MTU = 16 (CAN_MTU) => sizeof(struct can_frame) => 'legacy' CAN device + MTU = 72 (CANFD_MTU) => sizeof(struct canfd_frame) => CAN FD capable device + + The CAN device MTU can be retrieved e.g. with a SIOCGIFMTU ioctl() syscall. + N.B. CAN FD capable devices can also handle and send legacy CAN frames. + + FIXME: Add details about the CAN FD controller configuration when available. - 6.6 Supported CAN hardware + 6.7 Supported CAN hardware Please check the "Kconfig" file in "drivers/net/can" to get an actual list of the support CAN hardware. On the Socket CAN project website diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 6f896b9..406a522 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -468,6 +468,19 @@ tcp_syncookies - BOOLEAN SYN flood warnings in logs not being really flooded, your server is seriously misconfigured. +tcp_fastopen - INTEGER + Enable TCP Fast Open feature (draft-ietf-tcpm-fastopen) to send data + in the opening SYN packet. To use this feature, the client application + must not use connect(). Instead, it should use sendmsg() or sendto() + with MSG_FASTOPEN flag which performs a TCP handshake automatically. + + The values (bitmap) are: + 1: Enables sending data in the opening SYN on the client + 5: Enables sending data in the opening SYN on the client regardless + of cookie availability. + + Default: 0 + tcp_syn_retries - INTEGER Number of times initial SYNs for an active TCP connection attempt will be retransmitted. Should not be higher than 255. Default value @@ -551,6 +564,25 @@ tcp_thin_dupack - BOOLEAN Documentation/networking/tcp-thin.txt Default: 0 +tcp_limit_output_bytes - INTEGER + Controls TCP Small Queue limit per tcp socket. + TCP bulk sender tends to increase packets in flight until it + gets losses notifications. With SNDBUF autotuning, this can + result in a large amount of packets queued in qdisc/device + on the local machine, hurting latency of other flows, for + typical pfifo_fast qdiscs. + tcp_limit_output_bytes limits the number of bytes on qdisc + or device to reduce artificial RTT/cwnd and reduce bufferbloat. + Note: For GSO/TSO enabled flows, we try to have at least two + packets in flight. Reducing tcp_limit_output_bytes might also + reduce the size of individual GSO packet (64KB being the max) + Default: 131072 + +tcp_challenge_ack_limit - INTEGER + Limits number of Challenge ACK sent per second, as recommended + in RFC 5961 (Improving TCP's Robustness to Blind In-Window Attacks) + Default: 100 + UDP variables: udp_mem - vector of 3 INTEGERs: min, pressure, max @@ -857,9 +889,19 @@ accept_source_route - BOOLEAN FALSE (host) accept_local - BOOLEAN - Accept packets with local source addresses. In combination with - suitable routing, this can be used to direct packets between two - local interfaces over the wire and have them accepted properly. + Accept packets with local source addresses. In combination + with suitable routing, this can be used to direct packets + between two local interfaces over the wire and have them + accepted properly. + + rp_filter must be set to a non-zero value in order for + accept_local to have an effect. + + default FALSE + +route_localnet - BOOLEAN + Do not consider loopback addresses as martian source or destination + while routing. This enables the use of 127/8 for local routing purposes. default FALSE rp_filter - INTEGER @@ -1398,6 +1440,20 @@ path_max_retrans - INTEGER Default: 5 +pf_retrans - INTEGER + The number of retransmissions that will be attempted on a given path + before traffic is redirected to an alternate transport (should one + exist). Note this is distinct from path_max_retrans, as a path that + passes the pf_retrans threshold can still be used. Its only + deprioritized when a transmission path is selected by the stack. This + setting is primarily used to enable fast failover mechanisms without + having to reduce path_max_retrans to a very low value. See: + http://www.ietf.org/id/draft-nishida-tsvwg-sctp-failover-05.txt + for details. Note also that a value of pf_retrans > path_max_retrans + disables this feature + + Default: 0 + rto_initial - INTEGER The initial round trip timeout value in milliseconds that will be used in calculating round trip times. This is the initial time interval diff --git a/Documentation/networking/openvswitch.txt b/Documentation/networking/openvswitch.txt index b8a048b..8fa2dd1 100644 --- a/Documentation/networking/openvswitch.txt +++ b/Documentation/networking/openvswitch.txt @@ -118,7 +118,7 @@ essentially like this, ignoring metadata: Naively, to add VLAN support, it makes sense to add a new "vlan" flow key attribute to contain the VLAN tag, then continue to decode the encapsulated headers beyond the VLAN tag using the existing field -definitions. With this change, an TCP packet in VLAN 10 would have a +definitions. With this change, a TCP packet in VLAN 10 would have a flow key much like this: eth(...), vlan(vid=10, pcp=0), eth_type(0x0800), ip(proto=6, ...), tcp(...) diff --git a/Documentation/networking/s2io.txt b/Documentation/networking/s2io.txt index 4be0c03..d2a9f43 100644 --- a/Documentation/networking/s2io.txt +++ b/Documentation/networking/s2io.txt @@ -136,16 +136,6 @@ For more information, please review the AMD8131 errata at http://vip.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/ 26310_AMD-8131_HyperTransport_PCI-X_Tunnel_Revision_Guide_rev_3_18.pdf -6. Available Downloads -Neterion "s2io" driver in Red Hat and Suse 2.6-based distributions is kept up -to date, also the latest "s2io" code (including support for 2.4 kernels) is -available via "Support" link on the Neterion site: http://www.neterion.com. - -For Xframe User Guide (Programming manual), visit ftp site ns1.s2io.com, -user: linuxdocs password: HALdocs - -7. Support +6. Support For further support please contact either your 10GbE Xframe NIC vendor (IBM, -HP, SGI etc.) or click on the "Support" link on the Neterion site: -http://www.neterion.com. - +HP, SGI etc.) diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt index ab1e8d7..c676b9c 100644 --- a/Documentation/networking/stmmac.txt +++ b/Documentation/networking/stmmac.txt @@ -10,8 +10,8 @@ Currently this network device driver is for all STM embedded MAC/GMAC (i.e. 7xxx/5xxx SoCs), SPEAr (arm), Loongson1B (mips) and XLINX XC2V3000 FF1152AMT0221 D1215994A VIRTEX FPGA board. -DWC Ether MAC 10/100/1000 Universal version 3.60a (and older) and DWC Ether MAC 10/100 -Universal version 4.0 have been used for developing this driver. +DWC Ether MAC 10/100/1000 Universal version 3.60a (and older) and DWC Ether +MAC 10/100 Universal version 4.0 have been used for developing this driver. This driver supports both the platform bus and PCI. @@ -54,27 +54,27 @@ net_device structure enabling the scatter/gather feature. When one or more packets are received, an interrupt happens. The interrupts are not queued so the driver has to scan all the descriptors in the ring during the receive process. -This is based on NAPI so the interrupt handler signals only if there is work to be -done, and it exits. +This is based on NAPI so the interrupt handler signals only if there is work +to be done, and it exits. Then the poll method will be scheduled at some future point. The incoming packets are stored, by the DMA, in a list of pre-allocated socket buffers in order to avoid the memcpy (Zero-copy). 4.3) Timer-Driver Interrupt -Instead of having the device that asynchronously notifies the frame receptions, the -driver configures a timer to generate an interrupt at regular intervals. -Based on the granularity of the timer, the frames that are received by the device -will experience different levels of latency. Some NICs have dedicated timer -device to perform this task. STMMAC can use either the RTC device or the TMU -channel 2 on STLinux platforms. +Instead of having the device that asynchronously notifies the frame receptions, +the driver configures a timer to generate an interrupt at regular intervals. +Based on the granularity of the timer, the frames that are received by the +device will experience different levels of latency. Some NICs have dedicated +timer device to perform this task. STMMAC can use either the RTC device or the +TMU channel 2 on STLinux platforms. The timers frequency can be passed to the driver as parameter; when change it, take care of both hardware capability and network stability/performance impact. -Several performance tests on STM platforms showed this optimisation allows to spare -the CPU while having the maximum throughput. +Several performance tests on STM platforms showed this optimisation allows to +spare the CPU while having the maximum throughput. 4.4) WOL -Wake up on Lan feature through Magic and Unicast frames are supported for the GMAC -core. +Wake up on Lan feature through Magic and Unicast frames are supported for the +GMAC core. 4.5) DMA descriptors Driver handles both normal and enhanced descriptors. The latter has been only @@ -106,7 +106,8 @@ Several driver's information can be passed through the platform These are included in the include/linux/stmmac.h header file and detailed below as well: - struct plat_stmmacenet_data { +struct plat_stmmacenet_data { + char *phy_bus_name; int bus_id; int phy_addr; int interface; @@ -124,19 +125,24 @@ and detailed below as well: void (*bus_setup)(void __iomem *ioaddr); int (*init)(struct platform_device *pdev); void (*exit)(struct platform_device *pdev); + void *custom_cfg; + void *custom_data; void *bsp_priv; }; Where: + o phy_bus_name: phy bus name to attach to the stmmac. o bus_id: bus identifier. o phy_addr: the physical address can be passed from the platform. If it is set to -1 the driver will automatically detect it at run-time by probing all the 32 addresses. o interface: PHY device's interface. o mdio_bus_data: specific platform fields for the MDIO bus. - o pbl: the Programmable Burst Length is maximum number of beats to + o dma_cfg: internal DMA parameters + o pbl: the Programmable Burst Length is maximum number of beats to be transferred in one DMA transaction. GMAC also enables the 4xPBL by default. + o fixed_burst/mixed_burst/burst_len o clk_csr: fixed CSR Clock range selection. o has_gmac: uses the GMAC core. o enh_desc: if sets the MAC will use the enhanced descriptor structure. @@ -160,8 +166,9 @@ Where: this is sometime necessary on some platforms (e.g. ST boxes) where the HW needs to have set some PIO lines or system cfg registers. - o custom_cfg: this is a custom configuration that can be passed while - initialising the resources. + o custom_cfg/custom_data: this is a custom configuration that can be passed + while initialising the resources. + o bsp_priv: another private poiter. For MDIO bus The we have: @@ -180,7 +187,6 @@ Where: o irqs: list of IRQs, one per PHY. o probed_phy_irq: if irqs is NULL, use this for probed PHY. - For DMA engine we have the following internal fields that should be tuned according to the HW capabilities. @@ -251,9 +257,11 @@ reset procedure etc). o Makefile o stmmac_main.c: main network device driver; o stmmac_mdio.c: mdio functions; + o stmmac_pci: PCI driver; + o stmmac_platform.c: platform driver o stmmac_ethtool.c: ethtool support; o stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts - Only tested on ST40 platforms based. + (only tested on ST40 platforms based); o stmmac.h: private driver structure; o common.h: common definitions and VFTs; o descs.h: descriptor structure definitions; @@ -263,9 +271,11 @@ reset procedure etc). o dwmac100_core: MAC 100 core and dma code; o dwmac100_dma.c: dma funtions for the MAC chip; o dwmac1000.h: specific header file for the MAC; - o dwmac_lib.c: generic DMA functions shared among chips - o enh_desc.c: functions for handling enhanced descriptors - o norm_desc.c: functions for handling normal descriptors + o dwmac_lib.c: generic DMA functions shared among chips; + o enh_desc.c: functions for handling enhanced descriptors; + o norm_desc.c: functions for handling normal descriptors; + o chain_mode.c/ring_mode.c:: functions to manage RING/CHAINED modes; + o mmc_core.c/mmc.h: Management MAC Counters; 5) Debug Information @@ -298,7 +308,27 @@ All these are only useful during the developing stage and should never enabled inside the code for general usage. In fact, these can generate an huge amount of debug messages. -6) TODO: +6) Energy Efficient Ethernet + +Energy Efficient Ethernet(EEE) enables IEEE 802.3 MAC sublayer along +with a family of Physical layer to operate in the Low power Idle(LPI) +mode. The EEE mode supports the IEEE 802.3 MAC operation at 100Mbps, +1000Mbps & 10Gbps. + +The LPI mode allows power saving by switching off parts of the +communication device functionality when there is no data to be +transmitted & received. The system on both the side of the link can +disable some functionalities & save power during the period of low-link +utilization. The MAC controls whether the system should enter or exit +the LPI mode & communicate this to PHY. + +As soon as the interface is opened, the driver verifies if the EEE can +be supported. This is done by looking at both the DMA HW capability +register and the PHY devices MCD registers. +To enter in Tx LPI mode the driver needs to have a software timer +that enable and disable the LPI mode when there is nothing to be +transmitted. + +7) TODO: o XGMAC is not supported. - o Add the EEE - Energy Efficient Ethernet o Add the PTP - precision time protocol diff --git a/Documentation/networking/vxge.txt b/Documentation/networking/vxge.txt index d2e2997..bb76c66 100644 --- a/Documentation/networking/vxge.txt +++ b/Documentation/networking/vxge.txt @@ -91,10 +91,3 @@ v) addr_learn_en virtualization environment. Valid range: 0,1 (disabled, enabled respectively) Default: 0 - -4) Troubleshooting: -------------------- - -To resolve an issue with the source code or X3100 series adapter, please collect -the statistics, register dumps using ethool, relevant logs and email them to -support@neterion.com. diff --git a/Documentation/nfc/nfc-hci.txt b/Documentation/nfc/nfc-hci.txt index 320f933..89a339c 100644 --- a/Documentation/nfc/nfc-hci.txt +++ b/Documentation/nfc/nfc-hci.txt @@ -178,3 +178,36 @@ ANY_GET_PARAMETER to the reader A gate to get information on the target that was discovered). Typically, such an event will be propagated to NFC Core from MSGRXWQ context. + +Error management +---------------- + +Errors that occur synchronously with the execution of an NFC Core request are +simply returned as the execution result of the request. These are easy. + +Errors that occur asynchronously (e.g. in a background protocol handling thread) +must be reported such that upper layers don't stay ignorant that something +went wrong below and know that expected events will probably never happen. +Handling of these errors is done as follows: + +- driver (pn544) fails to deliver an incoming frame: it stores the error such +that any subsequent call to the driver will result in this error. Then it calls +the standard nfc_shdlc_recv_frame() with a NULL argument to report the problem +above. shdlc stores a EREMOTEIO sticky status, which will trigger SMW to +report above in turn. + +- SMW is basically a background thread to handle incoming and outgoing shdlc +frames. This thread will also check the shdlc sticky status and report to HCI +when it discovers it is not able to run anymore because of an unrecoverable +error that happened within shdlc or below. If the problem occurs during shdlc +connection, the error is reported through the connect completion. + +- HCI: if an internal HCI error happens (frame is lost), or HCI is reported an +error from a lower layer, HCI will either complete the currently executing +command with that error, or notify NFC Core directly if no command is executing. + +- NFC Core: when NFC Core is notified of an error from below and polling is +active, it will send a tag discovered event with an empty tag list to the user +space to let it know that the poll operation will never be able to detect a tag. +If polling is not active and the error was sticky, lower levels will return it +at next invocation. diff --git a/Documentation/power/devices.txt b/Documentation/power/devices.txt index 872815c..504dfe4 100644 --- a/Documentation/power/devices.txt +++ b/Documentation/power/devices.txt @@ -583,9 +583,10 @@ for the given device during all power transitions, instead of the respective subsystem-level callbacks. Specifically, if a device's pm_domain pointer is not NULL, the ->suspend() callback from the object pointed to by it will be executed instead of its subsystem's (e.g. bus type's) ->suspend() callback and -anlogously for all of the remaining callbacks. In other words, power management -domain callbacks, if defined for the given device, always take precedence over -the callbacks provided by the device's subsystem (e.g. bus type). +analogously for all of the remaining callbacks. In other words, power +management domain callbacks, if defined for the given device, always take +precedence over the callbacks provided by the device's subsystem (e.g. bus +type). The support for device power management domains is only relevant to platforms needing to use the same device driver power management callbacks in many @@ -598,7 +599,7 @@ it into account in any way. Device Low Power (suspend) States --------------------------------- Device low-power states aren't standard. One device might only handle -"on" and "off, while another might support a dozen different versions of +"on" and "off", while another might support a dozen different versions of "on" (how many engines are active?), plus a state that gets back to "on" faster than from a full "off". diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt index ac190cf..92341b8 100644 --- a/Documentation/power/swsusp.txt +++ b/Documentation/power/swsusp.txt @@ -33,6 +33,11 @@ echo shutdown > /sys/power/disk; echo disk > /sys/power/state echo platform > /sys/power/disk; echo disk > /sys/power/state +. If you would like to write hibernation image to swap and then suspend +to RAM (provided your platform supports it), you can try + +echo suspend > /sys/power/disk; echo disk > /sys/power/state + . If you have SATA disks, you'll need recent kernels with SATA suspend support. For suspend and resume to work, make sure your disk drivers are built into kernel -- not modules. [There's way to make diff --git a/Documentation/prctl/no_new_privs.txt b/Documentation/prctl/no_new_privs.txt new file mode 100644 index 0000000..f7be84f --- /dev/null +++ b/Documentation/prctl/no_new_privs.txt @@ -0,0 +1,57 @@ +The execve system call can grant a newly-started program privileges that +its parent did not have. The most obvious examples are setuid/setgid +programs and file capabilities. To prevent the parent program from +gaining these privileges as well, the kernel and user code must be +careful to prevent the parent from doing anything that could subvert the +child. For example: + + - The dynamic loader handles LD_* environment variables differently if + a program is setuid. + + - chroot is disallowed to unprivileged processes, since it would allow + /etc/passwd to be replaced from the point of view of a process that + inherited chroot. + + - The exec code has special handling for ptrace. + +These are all ad-hoc fixes. The no_new_privs bit (since Linux 3.5) is a +new, generic mechanism to make it safe for a process to modify its +execution environment in a manner that persists across execve. Any task +can set no_new_privs. Once the bit is set, it is inherited across fork, +clone, and execve and cannot be unset. With no_new_privs set, execve +promises not to grant the privilege to do anything that could not have +been done without the execve call. For example, the setuid and setgid +bits will no longer change the uid or gid; file capabilities will not +add to the permitted set, and LSMs will not relax constraints after +execve. + +To set no_new_privs, use prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0). + +Be careful, though: LSMs might also not tighten constraints on exec +in no_new_privs mode. (This means that setting up a general-purpose +service launcher to set no_new_privs before execing daemons may +interfere with LSM-based sandboxing.) + +Note that no_new_privs does not prevent privilege changes that do not +involve execve. An appropriately privileged task can still call +setuid(2) and receive SCM_RIGHTS datagrams. + +There are two main use cases for no_new_privs so far: + + - Filters installed for the seccomp mode 2 sandbox persist across + execve and can change the behavior of newly-executed programs. + Unprivileged users are therefore only allowed to install such filters + if no_new_privs is set. + + - By itself, no_new_privs can be used to reduce the attack surface + available to an unprivileged user. If everything running with a + given uid has no_new_privs set, then that uid will be unable to + escalate its privileges by directly attacking setuid, setgid, and + fcap-using binaries; it will need to compromise something without the + no_new_privs bit set first. + +In the future, other potentially dangerous kernel features could become +available to unprivileged tasks if no_new_privs is set. In principle, +several options to unshare(2) and clone(2) would be safe when +no_new_privs is set, and no_new_privs + chroot is considerable less +dangerous than chroot by itself. diff --git a/Documentation/stable_kernel_rules.txt b/Documentation/stable_kernel_rules.txt index f0ab5cf..4a7b54b 100644 --- a/Documentation/stable_kernel_rules.txt +++ b/Documentation/stable_kernel_rules.txt @@ -12,6 +12,12 @@ Rules on what kind of patches are accepted, and which ones are not, into the marked CONFIG_BROKEN), an oops, a hang, data corruption, a real security issue, or some "oh, that's not good" issue. In short, something critical. + - Serious issues as reported by a user of a distribution kernel may also + be considered if they fix a notable performance or interactivity issue. + As these fixes are not as obvious and have a higher risk of a subtle + regression they should only be submitted by a distribution kernel + maintainer and include an addendum linking to a bugzilla entry if it + exists and additional information on the user-visible impact. - New device IDs and quirks are also accepted. - No "theoretical race condition" issues, unless an explanation of how the race can be exploited is also provided. diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 310fe50..bf33aaa 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -1930,8 +1930,23 @@ The "pte_enc" field provides a value that can OR'ed into the hash PTE's RPN field (ie, it needs to be shifted left by 12 to OR it into the hash PTE second double word). +4.75 KVM_IRQFD -4.75 KVM_PPC_ALLOCATE_HTAB +Capability: KVM_CAP_IRQFD +Architectures: x86 +Type: vm ioctl +Parameters: struct kvm_irqfd (in) +Returns: 0 on success, -1 on error + +Allows setting an eventfd to directly trigger a guest interrupt. +kvm_irqfd.fd specifies the file descriptor to use as the eventfd and +kvm_irqfd.gsi specifies the irqchip pin toggled by this event. When +an event is tiggered on the eventfd, an interrupt is injected into +the guest using the specified gsi pin. The irqfd is removed using +the KVM_IRQFD_FLAG_DEASSIGN flag, specifying both kvm_irqfd.fd +and kvm_irqfd.gsi. + +4.76 KVM_PPC_ALLOCATE_HTAB Capability: KVM_CAP_PPC_ALLOC_HTAB Architectures: powerpc |