diff options
Diffstat (limited to 'arch/arm/mach-at91')
73 files changed, 1343 insertions, 961 deletions
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 45db05d..19505c0 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -9,15 +9,6 @@ config HAVE_AT91_DBGU0 config HAVE_AT91_DBGU1 bool -config HAVE_AT91_USART3 - bool - -config HAVE_AT91_USART4 - bool - -config HAVE_AT91_USART5 - bool - config AT91_SAM9_ALT_RESET bool default !ARCH_AT91X40 @@ -26,87 +17,129 @@ config AT91_SAM9G45_RESET bool default !ARCH_AT91X40 +config SOC_AT91SAM9 + bool + select GENERIC_CLOCKEVENTS + select CPU_ARM926T + menu "Atmel AT91 System-on-Chip" -choice - prompt "Atmel AT91 Processor" +comment "Atmel AT91 Processor" -config ARCH_AT91RM9200 +config SOC_AT91SAM9 + bool + select CPU_ARM926T + select AT91_SAM9_TIME + select AT91_SAM9_SMC + +config SOC_AT91RM9200 bool "AT91RM9200" select CPU_ARM920T select GENERIC_CLOCKEVENTS select HAVE_AT91_DBGU0 - select HAVE_AT91_USART3 -config ARCH_AT91SAM9260 - bool "AT91SAM9260 or AT91SAM9XE" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS +config SOC_AT91SAM9260 + bool "AT91SAM9260, AT91SAM9XE or AT91SAM9G20" + select SOC_AT91SAM9 select HAVE_AT91_DBGU0 - select HAVE_AT91_USART3 - select HAVE_AT91_USART4 - select HAVE_AT91_USART5 select HAVE_NET_MACB + help + Select this if you are using one of Atmel's AT91SAM9260, AT91SAM9XE + or AT91SAM9G20 SoC. -config ARCH_AT91SAM9261 - bool "AT91SAM9261" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS - select HAVE_FB_ATMEL - select HAVE_AT91_DBGU0 - -config ARCH_AT91SAM9G10 - bool "AT91SAM9G10" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS +config SOC_AT91SAM9261 + bool "AT91SAM9261 or AT91SAM9G10" + select SOC_AT91SAM9 select HAVE_AT91_DBGU0 select HAVE_FB_ATMEL + help + Select this if you are using one of Atmel's AT91SAM9261 or AT91SAM9G10 SoC. -config ARCH_AT91SAM9263 +config SOC_AT91SAM9263 bool "AT91SAM9263" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS + select SOC_AT91SAM9 + select HAVE_AT91_DBGU1 select HAVE_FB_ATMEL select HAVE_NET_MACB - select HAVE_AT91_DBGU1 -config ARCH_AT91SAM9RL +config SOC_AT91SAM9RL bool "AT91SAM9RL" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS - select HAVE_AT91_USART3 - select HAVE_FB_ATMEL - select HAVE_AT91_DBGU0 - -config ARCH_AT91SAM9G20 - bool "AT91SAM9G20" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS + select SOC_AT91SAM9 select HAVE_AT91_DBGU0 - select HAVE_AT91_USART3 - select HAVE_AT91_USART4 - select HAVE_AT91_USART5 - select HAVE_NET_MACB + select HAVE_FB_ATMEL -config ARCH_AT91SAM9G45 - bool "AT91SAM9G45" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS - select HAVE_AT91_USART3 +config SOC_AT91SAM9G45 + bool "AT91SAM9G45 or AT91SAM9M10 families" + select SOC_AT91SAM9 + select HAVE_AT91_DBGU1 select HAVE_FB_ATMEL select HAVE_NET_MACB - select HAVE_AT91_DBGU1 + help + Select this if you are using one of Atmel's AT91SAM9G45 family SoC. + This support covers AT91SAM9G45, AT91SAM9G46, AT91SAM9M10 and AT91SAM9M11. -config ARCH_AT91SAM9X5 +config SOC_AT91SAM9X5 bool "AT91SAM9x5 family" - select CPU_ARM926T - select GENERIC_CLOCKEVENTS + select SOC_AT91SAM9 + select HAVE_AT91_DBGU0 select HAVE_FB_ATMEL select HAVE_NET_MACB + help + Select this if you are using one of Atmel's AT91SAM9x5 family SoC. + This means that your SAM9 name finishes with a '5' (except if it is + AT91SAM9G45!). + This support covers AT91SAM9G15, AT91SAM9G25, AT91SAM9X25, AT91SAM9G35 + and AT91SAM9X35. + +config SOC_AT91SAM9N12 + bool "AT91SAM9N12 family" + select SOC_AT91SAM9 select HAVE_AT91_DBGU0 + select HAVE_FB_ATMEL + help + Select this if you are using Atmel's AT91SAM9N12 SoC. + +choice + prompt "Atmel AT91 Processor Devices for non DT boards" + +config ARCH_AT91_NONE + bool "None" + +config ARCH_AT91RM9200 + bool "AT91RM9200" + select SOC_AT91RM9200 + +config ARCH_AT91SAM9260 + bool "AT91SAM9260 or AT91SAM9XE" + select SOC_AT91SAM9260 + +config ARCH_AT91SAM9261 + bool "AT91SAM9261" + select SOC_AT91SAM9261 + +config ARCH_AT91SAM9G10 + bool "AT91SAM9G10" + select SOC_AT91SAM9261 + +config ARCH_AT91SAM9263 + bool "AT91SAM9263" + select SOC_AT91SAM9263 + +config ARCH_AT91SAM9RL + bool "AT91SAM9RL" + select SOC_AT91SAM9RL + +config ARCH_AT91SAM9G20 + bool "AT91SAM9G20" + select SOC_AT91SAM9260 + +config ARCH_AT91SAM9G45 + bool "AT91SAM9G45" + select SOC_AT91SAM9G45 config ARCH_AT91X40 bool "AT91x40" + depends on !MMU select ARCH_USES_GETTIMEOFFSET endchoice @@ -364,6 +397,7 @@ config MACH_AT91SAM9G20EK_2MMC Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and onwards. + <http://www.atmel.com/tools/SAM9G20-EK.aspx> config MACH_CPU9G20 bool "Eukrea CPU9G20 board" @@ -433,9 +467,10 @@ comment "AT91SAM9G45 Board Type" config MACH_AT91SAM9M10G45EK bool "Atmel AT91SAM9M10G45-EK Evaluation Kits" help - Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit. - "ES" at the end of the name means that this board is an - Engineering Sample. + Select this if you are using Atmel's AT91SAM9M10G45-EK Evaluation Kit. + Those boards can be populated with any SoC of AT91SAM9G45 or AT91SAM9M10 + families: AT91SAM9G45, AT91SAM9G46, AT91SAM9M10 and AT91SAM9M11. + <http://www.atmel.com/tools/SAM9M10-G45-EK.aspx> endif @@ -515,41 +550,6 @@ config AT91_TIMER_HZ system clock (of at least several MHz), rounding is less of a problem so it can be safer to use a decimal values like 100. -choice - prompt "Select a UART for early kernel messages" - -config AT91_EARLY_DBGU0 - bool "DBGU on rm9200, 9260/9g20, 9261/9g10 and 9rl" - depends on HAVE_AT91_DBGU0 - -config AT91_EARLY_DBGU1 - bool "DBGU on 9263 and 9g45" - depends on HAVE_AT91_DBGU1 - -config AT91_EARLY_USART0 - bool "USART0" - -config AT91_EARLY_USART1 - bool "USART1" - -config AT91_EARLY_USART2 - bool "USART2" - depends on ! ARCH_AT91X40 - -config AT91_EARLY_USART3 - bool "USART3" - depends on HAVE_AT91_USART3 - -config AT91_EARLY_USART4 - bool "USART4" - depends on HAVE_AT91_USART4 - -config AT91_EARLY_USART5 - bool "USART5" - depends on HAVE_AT91_USART5 - -endchoice - endmenu endif diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 8512e53..3bb7a51 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -10,17 +10,26 @@ obj- := obj-$(CONFIG_AT91_PMC_UNIT) += clock.o obj-$(CONFIG_AT91_SAM9_ALT_RESET) += at91sam9_alt_reset.o obj-$(CONFIG_AT91_SAM9G45_RESET) += at91sam9g45_reset.o +obj-$(CONFIG_SOC_AT91SAM9) += at91sam926x_time.o sam9_smc.o # CPU-specific support -obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devices.o -obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9G10) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o -obj-$(CONFIG_ARCH_AT91SAM9X5) += at91sam9x5.o at91sam926x_time.o sam9_smc.o +obj-$(CONFIG_SOC_AT91RM9200) += at91rm9200.o at91rm9200_time.o +obj-$(CONFIG_SOC_AT91SAM9260) += at91sam9260.o +obj-$(CONFIG_SOC_AT91SAM9261) += at91sam9261.o +obj-$(CONFIG_SOC_AT91SAM9263) += at91sam9263.o +obj-$(CONFIG_SOC_AT91SAM9G45) += at91sam9g45.o +obj-$(CONFIG_SOC_AT91SAM9N12) += at91sam9n12.o +obj-$(CONFIG_SOC_AT91SAM9X5) += at91sam9x5.o +obj-$(CONFIG_SOC_AT91SAM9RL) += at91sam9rl.o + +obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200_devices.o +obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260_devices.o +obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261_devices.o +obj-$(CONFIG_ARCH_AT91SAM9G10) += at91sam9261_devices.o +obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263_devices.o +obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl_devices.o +obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260_devices.o +obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45_devices.o obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o # AT91RM9200 board-specific support diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot index 0da66ca..9e84fe4 100644 --- a/arch/arm/mach-at91/Makefile.boot +++ b/arch/arm/mach-at91/Makefile.boot @@ -14,9 +14,23 @@ initrd_phys-y := 0x20410000 endif # Keep dtb files sorted alphabetically for each SoC +# sam9260 +dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9260.dtb +# sam9263 +dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9263ek.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9263.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9263.dtb # sam9g20 +dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9g20ek.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9g20ek_2mmc.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += kizbox.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9g20.dtb dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9g20.dtb # sam9g45 dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9m10g45ek.dtb +# sam9n12 +dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9n12ek.dtb # sam9x5 dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9g25ek.dtb diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c index 364c193..2691768 100644 --- a/arch/arm/mach-at91/at91rm9200.c +++ b/arch/arm/mach-at91/at91rm9200.c @@ -26,15 +26,6 @@ #include "clock.h" #include "sam9_smc.h" -static struct map_desc at91rm9200_io_desc[] __initdata = { - { - .virtual = AT91_VA_BASE_EMAC, - .pfn = __phys_to_pfn(AT91RM9200_BASE_EMAC), - .length = SZ_16K, - .type = MT_DEVICE, - }, -}; - /* -------------------------------------------------------------------- * Clocks * -------------------------------------------------------------------- */ @@ -258,18 +249,6 @@ static void __init at91rm9200_register_clocks(void) clk_register(&pck3); } -static struct clk_lookup console_clock_lookup; - -void __init at91rm9200_set_console_clock(int id) -{ - if (id >= ARRAY_SIZE(usart_clocks_lookups)) - return; - - console_clock_lookup.con_id = "usart"; - console_clock_lookup.clk = usart_clocks_lookups[id].clk; - clkdev_add(&console_clock_lookup); -} - /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ @@ -315,7 +294,6 @@ static void __init at91rm9200_map_io(void) { /* Map peripherals */ at91_init_sram(0, AT91RM9200_SRAM_BASE, AT91RM9200_SRAM_SIZE); - iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); } static void __init at91rm9200_ioremap_registers(void) diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 05774e5..e6b7d05 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -140,8 +140,8 @@ static struct macb_platform_data eth_data; static struct resource eth_resources[] = { [0] = { - .start = AT91_VA_BASE_EMAC, - .end = AT91_VA_BASE_EMAC + SZ_16K - 1, + .start = AT91RM9200_BASE_EMAC, + .end = AT91RM9200_BASE_EMAC + SZ_16K - 1, .flags = IORESOURCE_MEM, }, [1] = { @@ -1152,14 +1152,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) at91_uarts[portnr] = pdev; } -void __init at91_set_serial_console(unsigned portnr) -{ - if (portnr < ATMEL_MAX_UART) { - atmel_default_console_device = at91_uarts[portnr]; - at91rm9200_set_console_clock(at91_uarts[portnr]->id); - } -} - void __init at91_add_device_serial(void) { int i; @@ -1168,13 +1160,9 @@ void __init at91_add_device_serial(void) if (at91_uarts[i]) platform_device_register(at91_uarts[i]); } - - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); } #else void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -void __init at91_set_serial_console(unsigned portnr) {} void __init at91_add_device_serial(void) {} #endif diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index 46f7742..2b1e438 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -55,6 +55,13 @@ static struct clk adc_clk = { .pmc_mask = 1 << AT91SAM9260_ID_ADC, .type = CLK_TYPE_PERIPHERAL, }; + +static struct clk adc_op_clk = { + .name = "adc_op_clk", + .type = CLK_TYPE_PERIPHERAL, + .rate_hz = 5000000, +}; + static struct clk usart0_clk = { .name = "usart0_clk", .pmc_mask = 1 << AT91SAM9260_ID_US0, @@ -166,6 +173,7 @@ static struct clk *periph_clocks[] __initdata = { &pioB_clk, &pioC_clk, &adc_clk, + &adc_op_clk, &usart0_clk, &usart1_clk, &usart2_clk, @@ -268,18 +276,6 @@ static void __init at91sam9260_register_clocks(void) clk_register(&pck1); } -static struct clk_lookup console_clock_lookup; - -void __init at91sam9260_set_console_clock(int id) -{ - if (id >= ARRAY_SIZE(usart_clocks_lookups)) - return; - - console_clock_lookup.con_id = "usart"; - console_clock_lookup.clk = usart_clocks_lookups[id].clk; - clkdev_add(&console_clock_lookup); -} - /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 5652dde..0ded951 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -17,12 +17,15 @@ #include <linux/platform_device.h> #include <linux/i2c-gpio.h> +#include <linux/platform_data/at91_adc.h> + #include <mach/board.h> #include <mach/cpu.h> #include <mach/at91sam9260.h> #include <mach/at91sam9260_matrix.h> #include <mach/at91_matrix.h> #include <mach/at91sam9_smc.h> +#include <mach/at91_adc.h> #include "generic.h" @@ -702,25 +705,8 @@ static struct platform_device at91sam9260_tcb1_device = { .num_resources = ARRAY_SIZE(tcb1_resources), }; -#if defined(CONFIG_OF) -static struct of_device_id tcb_ids[] = { - { .compatible = "atmel,at91rm9200-tcb" }, - { /*sentinel*/ } -}; -#endif - static void __init at91_add_device_tc(void) { -#if defined(CONFIG_OF) - struct device_node *np; - - np = of_find_matching_node(NULL, tcb_ids); - if (np) { - of_node_put(np); - return; - } -#endif - platform_device_register(&at91sam9260_tcb0_device); platform_device_register(&at91sam9260_tcb1_device); } @@ -1229,14 +1215,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) at91_uarts[portnr] = pdev; } -void __init at91_set_serial_console(unsigned portnr) -{ - if (portnr < ATMEL_MAX_UART) { - atmel_default_console_device = at91_uarts[portnr]; - at91sam9260_set_console_clock(at91_uarts[portnr]->id); - } -} - void __init at91_add_device_serial(void) { int i; @@ -1245,13 +1223,9 @@ void __init at91_add_device_serial(void) if (at91_uarts[i]) platform_device_register(at91_uarts[i]); } - - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); } #else void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -void __init at91_set_serial_console(unsigned portnr) {} void __init at91_add_device_serial(void) {} #endif @@ -1369,6 +1343,93 @@ void __init at91_add_device_cf(struct at91_cf_data *data) void __init at91_add_device_cf(struct at91_cf_data * data) {} #endif +/* -------------------------------------------------------------------- + * ADCs + * -------------------------------------------------------------------- */ + +#if IS_ENABLED(CONFIG_AT91_ADC) +static struct at91_adc_data adc_data; + +static struct resource adc_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_ADC, + .end = AT91SAM9260_BASE_ADC + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_ADC, + .end = AT91SAM9260_ID_ADC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91_adc_device = { + .name = "at91_adc", + .id = -1, + .dev = { + .platform_data = &adc_data, + }, + .resource = adc_resources, + .num_resources = ARRAY_SIZE(adc_resources), +}; + +static struct at91_adc_trigger at91_adc_triggers[] = { + [0] = { + .name = "timer-counter-0", + .value = AT91_ADC_TRGSEL_TC0 | AT91_ADC_TRGEN, + }, + [1] = { + .name = "timer-counter-1", + .value = AT91_ADC_TRGSEL_TC1 | AT91_ADC_TRGEN, + }, + [2] = { + .name = "timer-counter-2", + .value = AT91_ADC_TRGSEL_TC2 | AT91_ADC_TRGEN, + }, + [3] = { + .name = "external", + .value = AT91_ADC_TRGSEL_EXTERNAL | AT91_ADC_TRGEN, + .is_external = true, + }, +}; + +static struct at91_adc_reg_desc at91_adc_register_g20 = { + .channel_base = AT91_ADC_CHR(0), + .drdy_mask = AT91_ADC_DRDY, + .status_register = AT91_ADC_SR, + .trigger_register = AT91_ADC_MR, +}; + +void __init at91_add_device_adc(struct at91_adc_data *data) +{ + if (!data) + return; + + if (test_bit(0, &data->channels_used)) + at91_set_A_periph(AT91_PIN_PC0, 0); + if (test_bit(1, &data->channels_used)) + at91_set_A_periph(AT91_PIN_PC1, 0); + if (test_bit(2, &data->channels_used)) + at91_set_A_periph(AT91_PIN_PC2, 0); + if (test_bit(3, &data->channels_used)) + at91_set_A_periph(AT91_PIN_PC3, 0); + + if (data->use_external_triggers) + at91_set_A_periph(AT91_PIN_PA22, 0); + + data->num_channels = 4; + data->startup_time = 10; + data->registers = &at91_adc_register_g20; + data->trigger_number = 4; + data->trigger_list = at91_adc_triggers; + + adc_data = *data; + platform_device_register(&at91_adc_device); +} +#else +void __init at91_add_device_adc(struct at91_adc_data *data) {} +#endif + /* -------------------------------------------------------------------- */ /* * These devices are always present and don't need any board-specific @@ -1376,6 +1437,9 @@ void __init at91_add_device_cf(struct at91_cf_data * data) {} */ static int __init at91_add_standard_devices(void) { + if (of_have_populated_dt()) + return 0; + at91_add_device_rtt(); at91_add_device_watchdog(); at91_add_device_tc(); diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 7de81e6..c77d503 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -239,18 +239,6 @@ static void __init at91sam9261_register_clocks(void) clk_register(&hck1); } -static struct clk_lookup console_clock_lookup; - -void __init at91sam9261_set_console_clock(int id) -{ - if (id >= ARRAY_SIZE(usart_clocks_lookups)) - return; - - console_clock_lookup.con_id = "usart"; - console_clock_lookup.clk = usart_clocks_lookups[id].clk; - clkdev_add(&console_clock_lookup); -} - /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 4db961a..9295e90 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -1051,14 +1051,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) at91_uarts[portnr] = pdev; } -void __init at91_set_serial_console(unsigned portnr) -{ - if (portnr < ATMEL_MAX_UART) { - atmel_default_console_device = at91_uarts[portnr]; - at91sam9261_set_console_clock(at91_uarts[portnr]->id); - } -} - void __init at91_add_device_serial(void) { int i; @@ -1067,13 +1059,9 @@ void __init at91_add_device_serial(void) if (at91_uarts[i]) platform_device_register(at91_uarts[i]); } - - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); } #else void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -void __init at91_set_serial_console(unsigned portnr) {} void __init at91_add_device_serial(void) {} #endif diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index ef301be..ed91c7e 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -199,6 +199,16 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_ID("pioC", &pioCDE_clk), CLKDEV_CON_ID("pioD", &pioCDE_clk), CLKDEV_CON_ID("pioE", &pioCDE_clk), + /* more usart lookup table for DT entries */ + CLKDEV_CON_DEV_ID("usart", "ffffee00.serial", &mck), + CLKDEV_CON_DEV_ID("usart", "fff8c000.serial", &usart0_clk), + CLKDEV_CON_DEV_ID("usart", "fff90000.serial", &usart1_clk), + CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk), + /* more tc lookup table for DT entries */ + CLKDEV_CON_DEV_ID("t0_clk", "fff7c000.timer", &tcb_clk), + CLKDEV_CON_DEV_ID("hclk", "a00000.ohci", &ohci_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk), + CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -255,18 +265,6 @@ static void __init at91sam9263_register_clocks(void) clk_register(&pck3); } -static struct clk_lookup console_clock_lookup; - -void __init at91sam9263_set_console_clock(int id) -{ - if (id >= ARRAY_SIZE(usart_clocks_lookups)) - return; - - console_clock_lookup.con_id = "usart"; - console_clock_lookup.clk = usart_clocks_lookups[id].clk; - clkdev_add(&console_clock_lookup); -} - /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index fe99206..175e000 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -953,8 +953,25 @@ static struct platform_device at91sam9263_tcb_device = { .num_resources = ARRAY_SIZE(tcb_resources), }; +#if defined(CONFIG_OF) +static struct of_device_id tcb_ids[] = { + { .compatible = "atmel,at91rm9200-tcb" }, + { /*sentinel*/ } +}; +#endif + static void __init at91_add_device_tc(void) { +#if defined(CONFIG_OF) + struct device_node *np; + + np = of_find_matching_node(NULL, tcb_ids); + if (np) { + of_node_put(np); + return; + } +#endif + platform_device_register(&at91sam9263_tcb_device); } #else @@ -1461,14 +1478,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) at91_uarts[portnr] = pdev; } -void __init at91_set_serial_console(unsigned portnr) -{ - if (portnr < ATMEL_MAX_UART) { - atmel_default_console_device = at91_uarts[portnr]; - at91sam9263_set_console_clock(at91_uarts[portnr]->id); - } -} - void __init at91_add_device_serial(void) { int i; @@ -1477,13 +1486,9 @@ void __init at91_add_device_serial(void) if (at91_uarts[i]) platform_device_register(at91_uarts[i]); } - - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); } #else void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -void __init at91_set_serial_console(unsigned portnr) {} void __init at91_add_device_serial(void) {} #endif @@ -1495,6 +1500,9 @@ void __init at91_add_device_serial(void) {} */ static int __init at91_add_standard_devices(void) { + if (of_have_populated_dt()) + return 0; + at91_add_device_rtt(); at91_add_device_watchdog(); at91_add_device_tc(); diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c index d222f83..4792682 100644 --- a/arch/arm/mach-at91/at91sam9g45.c +++ b/arch/arm/mach-at91/at91sam9g45.c @@ -176,6 +176,12 @@ static struct clk vdec_clk = { .type = CLK_TYPE_PERIPHERAL, }; +static struct clk adc_op_clk = { + .name = "adc_op_clk", + .type = CLK_TYPE_PERIPHERAL, + .rate_hz = 13200000, +}; + static struct clk *periph_clocks[] __initdata = { &pioA_clk, &pioB_clk, @@ -204,6 +210,7 @@ static struct clk *periph_clocks[] __initdata = { &isi_clk, &udphs_clk, &mmc1_clk, + &adc_op_clk, // irq0 }; @@ -242,6 +249,8 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_ID("pioC", &pioC_clk), CLKDEV_CON_ID("pioD", &pioDE_clk), CLKDEV_CON_ID("pioE", &pioDE_clk), + /* Fake adc clock */ + CLKDEV_CON_ID("adc_clk", &tsc_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -288,18 +297,6 @@ static void __init at91sam9g45_register_clocks(void) clk_register(&pck1); } -static struct clk_lookup console_clock_lookup; - -void __init at91sam9g45_set_console_clock(int id) -{ - if (id >= ARRAY_SIZE(usart_clocks_lookups)) - return; - - console_clock_lookup.con_id = "usart"; - console_clock_lookup.clk = usart_clocks_lookups[id].clk; - clkdev_add(&console_clock_lookup); -} - /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c index 6b008ae..f674724 100644 --- a/arch/arm/mach-at91/at91sam9g45_devices.c +++ b/arch/arm/mach-at91/at91sam9g45_devices.c @@ -19,9 +19,12 @@ #include <linux/i2c-gpio.h> #include <linux/atmel-mci.h> +#include <linux/platform_data/at91_adc.h> + #include <linux/fb.h> #include <video/atmel_lcdc.h> +#include <mach/at91_adc.h> #include <mach/board.h> #include <mach/at91sam9g45.h> #include <mach/at91sam9g45_matrix.h> @@ -69,15 +72,7 @@ static struct platform_device at_hdmac_device = { void __init at91_add_device_hdmac(void) { -#if defined(CONFIG_OF) - struct device_node *of_node = - of_find_node_by_name(NULL, "dma-controller"); - - if (of_node) - of_node_put(of_node); - else -#endif - platform_device_register(&at_hdmac_device); + platform_device_register(&at_hdmac_device); } #else void __init at91_add_device_hdmac(void) {} @@ -1094,25 +1089,8 @@ static struct platform_device at91sam9g45_tcb1_device = { .num_resources = ARRAY_SIZE(tcb1_resources), }; -#if defined(CONFIG_OF) -static struct of_device_id tcb_ids[] = { - { .compatible = "atmel,at91rm9200-tcb" }, - { /*sentinel*/ } -}; -#endif - static void __init at91_add_device_tc(void) { -#if defined(CONFIG_OF) - struct device_node *np; - - np = of_find_matching_node(NULL, tcb_ids); - if (np) { - of_node_put(np); - return; - } -#endif - platform_device_register(&at91sam9g45_tcb0_device); platform_device_register(&at91sam9g45_tcb1_device); } @@ -1207,6 +1185,104 @@ void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data) {} /* -------------------------------------------------------------------- + * ADC + * -------------------------------------------------------------------- */ + +#if IS_ENABLED(CONFIG_AT91_ADC) +static struct at91_adc_data adc_data; + +static struct resource adc_resources[] = { + [0] = { + .start = AT91SAM9G45_BASE_TSC, + .end = AT91SAM9G45_BASE_TSC + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9G45_ID_TSC, + .end = AT91SAM9G45_ID_TSC, + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device at91_adc_device = { + .name = "at91_adc", + .id = -1, + .dev = { + .platform_data = &adc_data, + }, + .resource = adc_resources, + .num_resources = ARRAY_SIZE(adc_resources), +}; + +static struct at91_adc_trigger at91_adc_triggers[] = { + [0] = { + .name = "external-rising", + .value = 1, + .is_external = true, + }, + [1] = { + .name = "external-falling", + .value = 2, + .is_external = true, + }, + [2] = { + .name = "external-any", + .value = 3, + .is_external = true, + }, + [3] = { + .name = "continuous", + .value = 6, + .is_external = false, + }, +}; + +static struct at91_adc_reg_desc at91_adc_register_g45 = { + .channel_base = AT91_ADC_CHR(0), + .drdy_mask = AT91_ADC_DRDY, + .status_register = AT91_ADC_SR, + .trigger_register = 0x08, +}; + +void __init at91_add_device_adc(struct at91_adc_data *data) +{ + if (!data) + return; + + if (test_bit(0, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD20, 0); + if (test_bit(1, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD21, 0); + if (test_bit(2, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD22, 0); + if (test_bit(3, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD23, 0); + if (test_bit(4, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD24, 0); + if (test_bit(5, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD25, 0); + if (test_bit(6, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD26, 0); + if (test_bit(7, &data->channels_used)) + at91_set_gpio_input(AT91_PIN_PD27, 0); + + if (data->use_external_triggers) + at91_set_A_periph(AT91_PIN_PD28, 0); + + data->num_channels = 8; + data->startup_time = 40; + data->registers = &at91_adc_register_g45; + data->trigger_number = 4; + data->trigger_list = at91_adc_triggers; + + adc_data = *data; + platform_device_register(&at91_adc_device); +} +#else +void __init at91_add_device_adc(struct at91_adc_data *data) {} +#endif + +/* -------------------------------------------------------------------- * RTT * -------------------------------------------------------------------- */ @@ -1741,14 +1817,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) at91_uarts[portnr] = pdev; } -void __init at91_set_serial_console(unsigned portnr) -{ - if (portnr < ATMEL_MAX_UART) { - atmel_default_console_device = at91_uarts[portnr]; - at91sam9g45_set_console_clock(at91_uarts[portnr]->id); - } -} - void __init at91_add_device_serial(void) { int i; @@ -1757,13 +1825,9 @@ void __init at91_add_device_serial(void) if (at91_uarts[i]) platform_device_register(at91_uarts[i]); } - - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); } #else void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -void __init at91_set_serial_console(unsigned portnr) {} void __init at91_add_device_serial(void) {} #endif @@ -1775,6 +1839,9 @@ void __init at91_add_device_serial(void) {} */ static int __init at91_add_standard_devices(void) { + if (of_have_populated_dt()) + return 0; + at91_add_device_hdmac(); at91_add_device_rtc(); at91_add_device_rtt(); diff --git a/arch/arm/mach-at91/at91sam9n12.c b/arch/arm/mach-at91/at91sam9n12.c new file mode 100644 index 0000000..0849466 --- /dev/null +++ b/arch/arm/mach-at91/at91sam9n12.c @@ -0,0 +1,233 @@ +/* + * SoC specific setup code for the AT91SAM9N12 + * + * Copyright (C) 2012 Atmel Corporation. + * + * Licensed under GPLv2 or later. + */ + +#include <linux/module.h> +#include <linux/dma-mapping.h> + +#include <asm/irq.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <mach/at91sam9n12.h> +#include <mach/at91_pmc.h> +#include <mach/cpu.h> +#include <mach/board.h> + +#include "soc.h" +#include "generic.h" +#include "clock.h" +#include "sam9_smc.h" + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk pioAB_clk = { + .name = "pioAB_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_PIOAB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioCD_clk = { + .name = "pioCD_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_PIOCD, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_USART0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_USART1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_USART2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart3_clk = { + .name = "usart3_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_USART3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi0_clk = { + .name = "twi0_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_TWI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi1_clk = { + .name = "twi1_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_TWI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi0_clk = { + .name = "spi0_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_SPI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi1_clk = { + .name = "spi1_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_SPI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk uart0_clk = { + .name = "uart0_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_UART0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk uart1_clk = { + .name = "uart1_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_UART1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tcb_clk = { + .name = "tcb_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_TCB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pwm_clk = { + .name = "pwm_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_PWM, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk adc_clk = { + .name = "adc_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_ADC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk dma_clk = { + .name = "dma_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_DMA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk uhp_clk = { + .name = "uhp", + .pmc_mask = 1 << AT91SAM9N12_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk udp_clk = { + .name = "udp_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk lcdc_clk = { + .name = "lcdc_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_LCDC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ssc_clk = { + .name = "ssc_clk", + .pmc_mask = 1 << AT91SAM9N12_ID_SSC, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioAB_clk, + &pioCD_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &usart3_clk, + &twi0_clk, + &twi1_clk, + &mmc_clk, + &spi0_clk, + &spi1_clk, + &lcdc_clk, + &uart0_clk, + &uart1_clk, + &tcb_clk, + &pwm_clk, + &adc_clk, + &dma_clk, + &uhp_clk, + &udp_clk, + &ssc_clk, +}; + +static struct clk_lookup periph_clocks_lookups[] = { + /* lookup table for DT entries */ + CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck), + CLKDEV_CON_DEV_ID("usart", "f801c000.serial", &usart0_clk), + CLKDEV_CON_DEV_ID("usart", "f8020000.serial", &usart1_clk), + CLKDEV_CON_DEV_ID("usart", "f8024000.serial", &usart2_clk), + CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk), + CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb_clk), + CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb_clk), + CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk), + CLKDEV_CON_ID("pioA", &pioAB_clk), + CLKDEV_CON_ID("pioB", &pioAB_clk), + CLKDEV_CON_ID("pioC", &pioCD_clk), + CLKDEV_CON_ID("pioD", &pioCD_clk), + /* additional fake clock for macb_hclk */ + CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &uhp_clk), + CLKDEV_CON_DEV_ID("ohci_clk", "500000.ohci", &uhp_clk), +}; + +/* + * The two programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; + +static void __init at91sam9n12_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + clk_register(&pck0); + clk_register(&pck1); + + clkdev_add_table(periph_clocks_lookups, + ARRAY_SIZE(periph_clocks_lookups)); + +} + +/* -------------------------------------------------------------------- + * AT91SAM9N12 processor initialization + * -------------------------------------------------------------------- */ + +static void __init at91sam9n12_map_io(void) +{ + at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE); +} + +void __init at91sam9n12_initialize(void) +{ + at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0); + + /* Register GPIO subsystem (using DT) */ + at91_gpio_init(NULL, 0); +} + +struct at91_init_soc __initdata at91sam9n12_soc = { + .map_io = at91sam9n12_map_io, + .register_clocks = at91sam9n12_register_clocks, + .init = at91sam9n12_initialize, +}; diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c index d9f2774..e420085 100644 --- a/arch/arm/mach-at91/at91sam9rl.c +++ b/arch/arm/mach-at91/at91sam9rl.c @@ -232,18 +232,6 @@ static void __init at91sam9rl_register_clocks(void) clk_register(&pck1); } -static struct clk_lookup console_clock_lookup; - -void __init at91sam9rl_set_console_clock(int id) -{ - if (id >= ARRAY_SIZE(usart_clocks_lookups)) - return; - - console_clock_lookup.con_id = "usart"; - console_clock_lookup.clk = usart_clocks_lookups[id].clk; - clkdev_add(&console_clock_lookup); -} - /* -------------------------------------------------------------------- * GPIO * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index fe4ae22..9c0b148 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -1192,14 +1192,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) at91_uarts[portnr] = pdev; } -void __init at91_set_serial_console(unsigned portnr) -{ - if (portnr < ATMEL_MAX_UART) { - atmel_default_console_device = at91_uarts[portnr]; - at91sam9rl_set_console_clock(at91_uarts[portnr]->id); - } -} - void __init at91_add_device_serial(void) { int i; @@ -1208,13 +1200,9 @@ void __init at91_add_device_serial(void) if (at91_uarts[i]) platform_device_register(at91_uarts[i]); } - - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); } #else void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -void __init at91_set_serial_console(unsigned portnr) {} void __init at91_add_device_serial(void) {} #endif diff --git a/arch/arm/mach-at91/at91sam9x5.c b/arch/arm/mach-at91/at91sam9x5.c index 13c8cae..1b144b4 100644 --- a/arch/arm/mach-at91/at91sam9x5.c +++ b/arch/arm/mach-at91/at91sam9x5.c @@ -120,6 +120,11 @@ static struct clk adc_clk = { .pmc_mask = 1 << AT91SAM9X5_ID_ADC, .type = CLK_TYPE_PERIPHERAL, }; +static struct clk adc_op_clk = { + .name = "adc_op_clk", + .type = CLK_TYPE_PERIPHERAL, + .rate_hz = 5000000, +}; static struct clk dma0_clk = { .name = "dma0_clk", .pmc_mask = 1 << AT91SAM9X5_ID_DMA0, @@ -205,6 +210,7 @@ static struct clk *periph_clocks[] __initdata = { &tcb0_clk, &pwm_clk, &adc_clk, + &adc_op_clk, &dma0_clk, &dma1_clk, &uhphs_clk, diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c index 2628384..271f994 100644 --- a/arch/arm/mach-at91/board-1arm.c +++ b/arch/arm/mach-at91/board-1arm.c @@ -47,20 +47,6 @@ static void __init onearm_init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata onearm_eth_data = { @@ -82,6 +68,16 @@ static struct at91_udc_data __initdata onearm_udc_data = { static void __init onearm_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&onearm_eth_data); diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 161efba..b7d8aa7 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -52,22 +52,6 @@ static void __init afeb9260_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -183,6 +167,18 @@ static struct at91_cf_data afeb9260_cf_data = { static void __init afeb9260_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&afeb9260_usbh_data); diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c index c6d44ee..29d3ef0 100644 --- a/arch/arm/mach-at91/board-cam60.c +++ b/arch/arm/mach-at91/board-cam60.c @@ -49,12 +49,6 @@ static void __init cam60_init_early(void) { /* Initialize processor: 10 MHz crystal */ at91_initialize(10000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -175,6 +169,8 @@ static void __init cam60_add_device_nand(void) static void __init cam60_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* SPI */ at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices)); diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index 59d9cf9..44328a6 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -44,17 +44,6 @@ static void __init carmeva_init_early(void) { /* Initialize processor: 20.000 MHz crystal */ at91_initialize(20000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata carmeva_eth_data = { @@ -139,6 +128,13 @@ static struct gpio_led carmeva_leds[] = { static void __init carmeva_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&carmeva_eth_data); diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 5f3680e..69951ec 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -52,34 +52,6 @@ static void __init cpu9krea_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | - ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART3 on ttyS4. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, 0); - - /* USART4 on ttyS5. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -352,6 +324,30 @@ static void __init cpu9krea_board_init(void) /* NOR */ cpu9krea_add_device_nor(); /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART3 on ttyS4. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, 0); + + /* USART4 on ttyS5. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&cpu9krea_usbh_data); diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index e094cc8..895cf2d 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -59,28 +59,6 @@ static void __init cpuat91_init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | - ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART2 on ttyS3 (Rx, Tx) */ - at91_register_uart(AT91RM9200_ID_US2, 3, 0); - - /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata cpuat91_eth_data = { @@ -161,6 +139,24 @@ static struct platform_device *platform_devices[] __initdata = { static void __init cpuat91_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART2 on ttyS3 (Rx, Tx) */ + at91_register_uart(AT91RM9200_ID_US2, 3, 0); + + /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS | + ATMEL_UART_RTS); at91_add_device_serial(); /* LEDs. */ at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds)); diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index 1a1547b..cd81336 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -47,15 +47,6 @@ static void __init csb337_init_early(void) { /* Initialize processor: 3.6864 MHz crystal */ at91_initialize(3686400); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); - - /* DBGU on ttyS0 */ - at91_register_uart(0, 0, 0); - - /* make console=ttyS0 the default */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata csb337_eth_data = { @@ -228,7 +219,11 @@ static struct gpio_led csb_leds[] = { static void __init csb337_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); /* Serial */ + /* DBGU on ttyS0 */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&csb337_eth_data); diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index f650bf3..7c8b05a 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -44,12 +44,6 @@ static void __init csb637_init_early(void) { /* Initialize processor: 3.6864 MHz crystal */ at91_initialize(3686400); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* make console=ttyS0 (ie, DBGU) the default */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata csb637_eth_data = { @@ -118,6 +112,8 @@ static void __init csb637_board_init(void) /* LED(s) */ at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds)); /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&csb637_eth_data); diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c index c18d4d3..a1fce05 100644 --- a/arch/arm/mach-at91/board-dt.c +++ b/arch/arm/mach-at91/board-dt.c @@ -1,10 +1,6 @@ /* * Setup code for AT91SAM Evaluation Kits with Device Tree support * - * Covers: * AT91SAM9G45-EKES board - * * AT91SAM9M10-EKES board - * * AT91SAM9M10G45-EK board - * * Copyright (C) 2011 Atmel, * 2011 Nicolas Ferre <nicolas.ferre@atmel.com> * @@ -49,9 +45,7 @@ static void __init at91_dt_device_init(void) } static const char *at91_dt_board_compat[] __initdata = { - "atmel,at91sam9m10g45ek", - "atmel,at91sam9x5ek", - "calao,usb-a9g20", + "atmel,at91sam9", NULL }; diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index d302ca3..bd10172 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -44,20 +44,6 @@ static void __init eb9200_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART2 on ttyS2. (Rx, Tx) - IRDA */ - at91_register_uart(AT91RM9200_ID_US2, 2, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata eb9200_eth_data = { @@ -101,6 +87,16 @@ static struct i2c_board_info __initdata eb9200_i2c_devices[] = { static void __init eb9200_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART2 on ttyS2. (Rx, Tx) - IRDA */ + at91_register_uart(AT91RM9200_ID_US2, 2, 0); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&eb9200_eth_data); diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 69966ce..89cc372 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -50,18 +50,6 @@ static void __init ecb_at91init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata ecb_at91eth_data = { @@ -151,7 +139,15 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = { static void __init ecb_at91board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx & Tx only) */ + at91_register_uart(AT91RM9200_ID_US0, 1, 0); at91_add_device_serial(); /* Ethernet */ diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c index f23aabe..558546c 100644 --- a/arch/arm/mach-at91/board-eco920.c +++ b/arch/arm/mach-at91/board-eco920.c @@ -37,15 +37,6 @@ static void __init eco920_init_early(void) at91rm9200_set_type(ARCH_REVISON_9200_PQFP); at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); - - /* DBGU on ttyS0. (Rx & Tx only */ - at91_register_uart(0, 0, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata eco920_eth_data = { @@ -103,6 +94,10 @@ static struct spi_board_info eco920_spi_devices[] = { static void __init eco920_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); + /* DBGU on ttyS0. (Rx & Tx only */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); at91_add_device_eth(&eco920_eth_data); at91_add_device_usbh(&eco920_usbh_data); diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c index 1815152..47658f7 100644 --- a/arch/arm/mach-at91/board-flexibity.c +++ b/arch/arm/mach-at91/board-flexibity.c @@ -41,12 +41,6 @@ static void __init flexibity_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* USB Host port */ @@ -143,6 +137,8 @@ static struct gpio_led flexibity_leds[] = { static void __init flexibity_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&flexibity_usbh_data); diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index caf017f..33411e6 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -61,44 +61,6 @@ static void __init foxg20_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS - | ATMEL_UART_RTS - | ATMEL_UART_DTR - | ATMEL_UART_DSR - | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, 0); - - /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); - - /* Set the internal pull-up resistor on DRXD */ - at91_set_A_periph(AT91_PIN_PB14, 1); - } /* @@ -241,6 +203,39 @@ static struct i2c_board_info __initdata foxg20_i2c_devices[] = { static void __init foxg20_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS + | ATMEL_UART_RTS + | ATMEL_UART_DTR + | ATMEL_UART_DSR + | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); + + /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); + + /* Set the internal pull-up resistor on DRXD */ + at91_set_A_periph(AT91_PIN_PB14, 1); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&foxg20_usbh_data); diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c index 230e719..3e0dfa6 100644 --- a/arch/arm/mach-at91/board-gsia18s.c +++ b/arch/arm/mach-at91/board-gsia18s.c @@ -41,38 +41,6 @@ static void __init gsia18s_init_early(void) { stamp9g20_init_early(); - - /* - * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI). - * Used for Internal Analog Modem. - */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS | - ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - /* - * USART1 on ttyS2 (Rx, Tx, CTS, RTS). - * Used for GPS or WiFi or Data stream. - */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); - /* - * USART2 on ttyS3 (Rx, Tx, CTS, RTS). - * Used for External Modem. - */ - at91_register_uart(AT91SAM9260_ID_US2, 3, - ATMEL_UART_CTS | ATMEL_UART_RTS); - /* - * USART3 on ttyS4 (Rx, Tx, RTS). - * Used for RS-485. - */ - at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS); - - /* - * USART4 on ttyS5 (Rx, Tx). - * Used for TRX433 Radio Module. - */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); } /* @@ -558,6 +526,37 @@ static int __init gsia18s_power_off_init(void) static void __init gsia18s_board_init(void) { + /* + * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI). + * Used for Internal Analog Modem. + */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS | ATMEL_UART_RTS | + ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + /* + * USART1 on ttyS2 (Rx, Tx, CTS, RTS). + * Used for GPS or WiFi or Data stream. + */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS | ATMEL_UART_RTS); + /* + * USART2 on ttyS3 (Rx, Tx, CTS, RTS). + * Used for External Modem. + */ + at91_register_uart(AT91SAM9260_ID_US2, 3, + ATMEL_UART_CTS | ATMEL_UART_RTS); + /* + * USART3 on ttyS4 (Rx, Tx, RTS). + * Used for RS-485. + */ + at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS); + + /* + * USART4 on ttyS5 (Rx, Tx). + * Used for TRX433 Radio Module. + */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_udc(&udc_data); diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c index efde1b2..f260657 100644 --- a/arch/arm/mach-at91/board-kafa.c +++ b/arch/arm/mach-at91/board-kafa.c @@ -47,18 +47,6 @@ static void __init kafa_init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Set up the LEDs */ - at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata kafa_eth_data = { @@ -79,7 +67,15 @@ static struct at91_udc_data __initdata kafa_udc_data = { static void __init kafa_board_init(void) { + /* Set up the LEDs */ + at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&kafa_eth_data); diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index 59b92aa..ba39db5 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -50,24 +50,6 @@ static void __init kb9202_init_early(void) /* Initialize processor: 10 MHz crystal */ at91_initialize(10000000); - - /* Set up the LEDs */ - at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); - - /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ - at91_register_uart(AT91RM9200_ID_US1, 2, 0); - - /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ - at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata kb9202_eth_data = { @@ -115,7 +97,21 @@ static struct atmel_nand_data __initdata kb9202_nand_data = { static void __init kb9202_board_init(void) { + /* Set up the LEDs */ + at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx & Tx only) */ + at91_register_uart(AT91RM9200_ID_US0, 1, 0); + + /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ + at91_register_uart(AT91RM9200_ID_US1, 2, 0); + + /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&kb9202_eth_data); diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index 57d5f6a..d2f4cc1 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -55,15 +55,6 @@ static void __init neocore926_init_early(void) { /* Initialize processor: 20 MHz crystal */ at91_initialize(20000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -341,6 +332,11 @@ static struct ac97c_platform_data neocore926_ac97_data = { static void __init neocore926_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c index b4a12fc..7fe6383 100644 --- a/arch/arm/mach-at91/board-pcontrol-g20.c +++ b/arch/arm/mach-at91/board-pcontrol-g20.c @@ -40,17 +40,6 @@ static void __init pcontrol_g20_init_early(void) { stamp9g20_init_early(); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ - at91_register_uart(AT91SAM9260_ID_US4, 3, 0); } static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { @@ -199,6 +188,16 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = { static void __init pcontrol_g20_board_init(void) { + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ + at91_register_uart(AT91SAM9260_ID_US4, 3, 0); stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_eth(&macb_data); diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 59e35dd..b45c0a5 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -48,17 +48,6 @@ static void __init picotux200_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata picotux200_eth_data = { @@ -106,6 +95,13 @@ static struct platform_device picotux200_flash = { static void __init picotux200_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&picotux200_eth_data); diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index b6ed5ed..0c61bf0 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -52,24 +52,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.000 MHz crystal */ at91_initialize(12000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS1 (ie, USART0) */ - at91_set_serial_console(1); - } /* @@ -235,6 +217,19 @@ static struct gpio_led ek_leds[] = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index 01332aa..afd7a47 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -50,20 +50,6 @@ static void __init dk_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata dk_eth_data = { @@ -190,7 +176,17 @@ static struct gpio_led dk_leds[] = { static void __init dk_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&dk_eth_data); diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index b2e4fe2..2b15b8a 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -50,20 +50,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static struct macb_platform_data __initdata ek_eth_data = { @@ -161,7 +147,17 @@ static struct gpio_led ek_leds[] = { static void __init ek_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&ek_eth_data); diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c index af0750f..24ab9be 100644 --- a/arch/arm/mach-at91/board-rsi-ews.c +++ b/arch/arm/mach-at91/board-rsi-ews.c @@ -35,26 +35,6 @@ static void __init rsi_ews_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9); - - /* DBGU on ttyS0. (Rx & Tx only) */ - /* This one is for debugging */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - /* Dialin/-out modem interface */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART3 on ttyS4. (Rx, Tx, RTS) */ - /* RS485 communication */ - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -204,7 +184,23 @@ static struct platform_device rsiews_nor_flash = { */ static void __init rsi_ews_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + /* This one is for debugging */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + /* Dialin/-out modem interface */ + at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART3 on ttyS4. (Rx, Tx, RTS) */ + /* RS485 communication */ + at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS); at91_add_device_serial(); at91_set_gpio_output(AT91_PIN_PA21, 0); /* Ethernet */ diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index e8b116b..cdd21f2 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -48,23 +48,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -184,7 +167,20 @@ static struct at91_mmc_data __initdata ek_mmc_data = { static void __init ek_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index d5aec55..7b3c391 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -54,20 +54,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -320,6 +306,16 @@ static void __init ek_add_device_buttons(void) {} static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 065fed3..2736453 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -58,15 +58,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -577,7 +568,12 @@ static struct gpio_led ek_leds[] = { static void __init ek_board_init(void) { + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 2ffe50f..983cb98 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -57,15 +57,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 16.367 MHz crystal */ at91_initialize(16367660); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -412,6 +403,11 @@ static struct at91_can_data ek_can_data = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 8923ec9..6860d34 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -32,6 +32,8 @@ #include <linux/regulator/fixed.h> #include <linux/regulator/consumer.h> +#include <linux/platform_data/at91_adc.h> + #include <mach/hardware.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -65,20 +67,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -318,6 +306,16 @@ static void __init ek_add_device_buttons(void) static void __init ek_add_device_buttons(void) {} #endif +/* + * ADCs + */ + +static struct at91_adc_data ek_adc_data = { + .channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3), + .use_external_triggers = true, + .vref = 3300, +}; + #if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { REGULATOR_SUPPLY("AVDD", "0-001b"), @@ -372,6 +370,16 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); @@ -393,6 +401,8 @@ static void __init ek_board_init(void) ek_add_device_gpio_leds(); /* Push Buttons */ ek_add_device_buttons(); + /* ADCs */ + at91_add_device_adc(&ek_adc_data); /* PCK0 provides MCLK to the WM8731 */ at91_set_B_periph(AT91_PIN_PC1, 0); /* SSC (for WM8731) */ diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index c88e908..63163dc 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -27,6 +27,8 @@ #include <linux/atmel-mci.h> #include <linux/delay.h> +#include <linux/platform_data/at91_adc.h> + #include <mach/hardware.h> #include <video/atmel_lcdc.h> #include <media/soc_camera.h> @@ -53,16 +55,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.000 MHz crystal */ at91_initialize(12000000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 not connected on the -EK board */ - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -315,6 +307,14 @@ static struct at91_tsadcc_data ek_tsadcc_data = { .ts_sample_hold_time = 0x0a, }; +/* + * ADCs + */ +static struct at91_adc_data ek_adc_data = { + .channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7), + .use_external_triggers = true, + .vref = 3300, +}; /* * GPIO Buttons @@ -457,6 +457,12 @@ static struct platform_device *devices[] __initdata = { static void __init ek_board_init(void) { /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 not connected on the -EK board */ + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB HS Host */ at91_add_device_usbh_ohci(&ek_usbh_hs_data); @@ -480,6 +486,8 @@ static void __init ek_board_init(void) at91_add_device_lcdc(&ek_lcdc_data); /* Touch Screen */ at91_add_device_tsadcc(&ek_tsadcc_data); + /* ADC */ + at91_add_device_adc(&ek_adc_data); /* Push Buttons */ ek_add_device_buttons(); /* AC97 */ diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index b109ce2..be3239f 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -42,15 +42,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.000 MHz crystal */ at91_initialize(12000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -296,6 +287,11 @@ static void __init ek_add_device_buttons(void) {} static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB HS */ at91_add_device_usba(&ek_usba_udc_data); diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c index ebc9d01..9d446f1 100644 --- a/arch/arm/mach-at91/board-snapper9260.c +++ b/arch/arm/mach-at91/board-snapper9260.c @@ -43,16 +43,6 @@ static void __init snapper9260_init_early(void) { at91_initialize(18432000); - - /* Debug on ttyS0 */ - at91_register_uart(0, 0, 0); - at91_set_serial_console(0); - - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS); - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); - at91_register_uart(AT91SAM9260_ID_US2, 3, 0); } static struct at91_usbh_data __initdata snapper9260_usbh_data = { @@ -168,6 +158,14 @@ static void __init snapper9260_board_init(void) snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31); i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1); + /* Debug on ttyS0 */ + at91_register_uart(0, 0, 0); + + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS | ATMEL_UART_RTS); + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS | ATMEL_UART_RTS); + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); at91_add_device_serial(); at91_add_device_usbh(&snapper9260_usbh_data); at91_add_device_udc(&snapper9260_udc_data); diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 7640049..ee86f9d 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -36,44 +36,6 @@ void __init stamp9g20_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init stamp9g20evb_init_early(void) -{ - stamp9g20_init_early(); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); -} - -static void __init portuxg20_init_early(void) -{ - stamp9g20_init_early(); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx, Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx, Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); } /* @@ -254,6 +216,8 @@ void add_w1(void) void __init stamp9g20_board_init(void) { /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* NAND */ add_device_nand(); @@ -269,6 +233,22 @@ void __init stamp9g20_board_init(void) static void __init portuxg20_board_init(void) { + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx, Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx, Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); stamp9g20_board_init(); /* USB Host */ at91_add_device_usbh(&usbh_data); @@ -286,6 +266,10 @@ static void __init portuxg20_board_init(void) static void __init stamp9g20evb_board_init(void) { + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); stamp9g20_board_init(); /* USB Host */ at91_add_device_usbh(&usbh_data); @@ -303,7 +287,7 @@ MACHINE_START(PORTUXG20, "taskit PortuxG20") /* Maintainer: taskit GmbH */ .timer = &at91sam926x_timer, .map_io = at91_map_io, - .init_early = portuxg20_init_early, + .init_early = stamp9g20_init_early, .init_irq = at91_init_irq_default, .init_machine = portuxg20_board_init, MACHINE_END @@ -312,7 +296,7 @@ MACHINE_START(STAMP9G20, "taskit Stamp9G20") /* Maintainer: taskit GmbH */ .timer = &at91sam926x_timer, .map_io = at91_map_io, - .init_early = stamp9g20evb_init_early, + .init_early = stamp9g20_init_early, .init_irq = at91_init_irq_default, .init_machine = stamp9g20evb_board_init, MACHINE_END diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index b7483a3..95393fc 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -53,12 +53,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.00 MHz crystal */ at91_initialize(12000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -178,6 +172,10 @@ static struct mtd_partition __initdata ek_nand_partition[] = { .offset = MTDPART_OFS_NXTBLK, .size = SZ_128K, }, { + .name = "oftree", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_128K, + }, { .name = "kernel", .offset = MTDPART_OFS_NXTBLK, .size = 4 * SZ_1M, @@ -325,6 +323,8 @@ static void __init ek_add_device_leds(void) static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index 38dd279..d56665e 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -58,26 +58,6 @@ static void __init yl9200_init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */ - at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART0 on ttyS2. (Rx & Tx only to JP3) */ - at91_register_uart(AT91RM9200_ID_US0, 2, 0); - - /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ - at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -560,7 +540,23 @@ void __init yl9200_add_device_video(void) {} static void __init yl9200_board_init(void) { + /* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */ + at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17); + /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART0 on ttyS2. (Rx & Tx only to JP3) */ + at91_register_uart(AT91RM9200_ID_US0, 2, 0); + + /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&yl9200_eth_data); diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index 6b69282..de2ec6b 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -58,13 +58,15 @@ EXPORT_SYMBOL_GPL(at91_pmc_base); #define cpu_has_800M_plla() ( cpu_is_at91sam9g20() \ || cpu_is_at91sam9g45() \ - || cpu_is_at91sam9x5()) + || cpu_is_at91sam9x5() \ + || cpu_is_at91sam9n12()) #define cpu_has_300M_plla() (cpu_is_at91sam9g10()) #define cpu_has_pllb() (!(cpu_is_at91sam9rl() \ || cpu_is_at91sam9g45() \ - || cpu_is_at91sam9x5())) + || cpu_is_at91sam9x5() \ + || cpu_is_at91sam9n12())) #define cpu_has_upll() (cpu_is_at91sam9g45() \ || cpu_is_at91sam9x5()) @@ -78,12 +80,15 @@ EXPORT_SYMBOL_GPL(at91_pmc_base); || cpu_is_at91sam9x5())) #define cpu_has_plladiv2() (cpu_is_at91sam9g45() \ - || cpu_is_at91sam9x5()) + || cpu_is_at91sam9x5() \ + || cpu_is_at91sam9n12()) #define cpu_has_mdiv3() (cpu_is_at91sam9g45() \ - || cpu_is_at91sam9x5()) + || cpu_is_at91sam9x5() \ + || cpu_is_at91sam9n12()) -#define cpu_has_alt_prescaler() (cpu_is_at91sam9x5()) +#define cpu_has_alt_prescaler() (cpu_is_at91sam9x5() \ + || cpu_is_at91sam9n12()) static LIST_HEAD(clocks); static DEFINE_SPINLOCK(clk_lock); diff --git a/arch/arm/mach-at91/cpuidle.c b/arch/arm/mach-at91/cpuidle.c index ece1f9a..0c63815 100644 --- a/arch/arm/mach-at91/cpuidle.c +++ b/arch/arm/mach-at91/cpuidle.c @@ -21,6 +21,7 @@ #include <linux/export.h> #include <asm/proc-fns.h> #include <asm/cpuidle.h> +#include <mach/cpu.h> #include "pm.h" @@ -33,7 +34,12 @@ static int at91_enter_idle(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index) { - at91_standby(); + if (cpu_is_at91rm9200()) + at91rm9200_standby(); + else if (cpu_is_at91sam9g45()) + at91sam9g45_standby(); + else + at91sam9_standby(); return index; } diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index dd9b346..0a60bf8 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -40,17 +40,6 @@ extern struct sys_timer at91sam926x_timer; extern struct sys_timer at91x40_timer; /* Clocks */ -/* - * function to specify the clock of the default console. As we do not - * use the device/driver bus, the dev_name is not intialize. So we need - * to link the clock to a specific con_id only "usart" - */ -extern void __init at91rm9200_set_console_clock(int id); -extern void __init at91sam9260_set_console_clock(int id); -extern void __init at91sam9261_set_console_clock(int id); -extern void __init at91sam9263_set_console_clock(int id); -extern void __init at91sam9rl_set_console_clock(int id); -extern void __init at91sam9g45_set_console_clock(int id); #ifdef CONFIG_AT91_PMC_UNIT extern int __init at91_clock_init(unsigned long main_clock); extern int __init at91_dt_clock_init(void); diff --git a/arch/arm/mach-at91/include/mach/at91rm9200.h b/arch/arm/mach-at91/include/mach/at91rm9200.h index 603e6aa..e67317c 100644 --- a/arch/arm/mach-at91/include/mach/at91rm9200.h +++ b/arch/arm/mach-at91/include/mach/at91rm9200.h @@ -88,11 +88,6 @@ #define AT91RM9200_BASE_RTC 0xfffffe00 /* Real-Time Clock */ #define AT91RM9200_BASE_MC 0xffffff00 /* Memory Controllers */ -#define AT91_USART0 AT91RM9200_BASE_US0 -#define AT91_USART1 AT91RM9200_BASE_US1 -#define AT91_USART2 AT91RM9200_BASE_US2 -#define AT91_USART3 AT91RM9200_BASE_US3 - /* * Internal Memory. */ diff --git a/arch/arm/mach-at91/include/mach/at91sam9260.h b/arch/arm/mach-at91/include/mach/at91sam9260.h index 08ae9af..416c7b6 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9260.h +++ b/arch/arm/mach-at91/include/mach/at91sam9260.h @@ -95,13 +95,6 @@ #define AT91SAM9260_BASE_WDT 0xfffffd40 #define AT91SAM9260_BASE_GPBR 0xfffffd50 -#define AT91_USART0 AT91SAM9260_BASE_US0 -#define AT91_USART1 AT91SAM9260_BASE_US1 -#define AT91_USART2 AT91SAM9260_BASE_US2 -#define AT91_USART3 AT91SAM9260_BASE_US3 -#define AT91_USART4 AT91SAM9260_BASE_US4 -#define AT91_USART5 AT91SAM9260_BASE_US5 - /* * Internal Memory. diff --git a/arch/arm/mach-at91/include/mach/at91sam9261.h b/arch/arm/mach-at91/include/mach/at91sam9261.h index 44fbdc1..a041406 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9261.h +++ b/arch/arm/mach-at91/include/mach/at91sam9261.h @@ -79,10 +79,6 @@ #define AT91SAM9261_BASE_WDT 0xfffffd40 #define AT91SAM9261_BASE_GPBR 0xfffffd50 -#define AT91_USART0 AT91SAM9261_BASE_US0 -#define AT91_USART1 AT91SAM9261_BASE_US1 -#define AT91_USART2 AT91SAM9261_BASE_US2 - /* * Internal Memory. diff --git a/arch/arm/mach-at91/include/mach/at91sam9263.h b/arch/arm/mach-at91/include/mach/at91sam9263.h index d96cbb2..d201029 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9263.h +++ b/arch/arm/mach-at91/include/mach/at91sam9263.h @@ -95,10 +95,6 @@ #define AT91SAM9263_BASE_RTT1 0xfffffd50 #define AT91SAM9263_BASE_GPBR 0xfffffd60 -#define AT91_USART0 AT91SAM9263_BASE_US0 -#define AT91_USART1 AT91SAM9263_BASE_US1 -#define AT91_USART2 AT91SAM9263_BASE_US2 - #define AT91_SMC AT91_SMC0 /* diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h index d052abc..3a4da24 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9g45.h +++ b/arch/arm/mach-at91/include/mach/at91sam9g45.h @@ -106,11 +106,6 @@ #define AT91SAM9G45_BASE_RTC 0xfffffdb0 #define AT91SAM9G45_BASE_GPBR 0xfffffd60 -#define AT91_USART0 AT91SAM9G45_BASE_US0 -#define AT91_USART1 AT91SAM9G45_BASE_US1 -#define AT91_USART2 AT91SAM9G45_BASE_US2 -#define AT91_USART3 AT91SAM9G45_BASE_US3 - /* * Internal Memory. */ diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12.h b/arch/arm/mach-at91/include/mach/at91sam9n12.h new file mode 100644 index 0000000..d374b87 --- /dev/null +++ b/arch/arm/mach-at91/include/mach/at91sam9n12.h @@ -0,0 +1,60 @@ +/* + * SoC specific header file for the AT91SAM9N12 + * + * Copyright (C) 2012 Atmel Corporation + * + * Common definitions, based on AT91SAM9N12 SoC datasheet + * + * Licensed under GPLv2 or later + */ + +#ifndef _AT91SAM9N12_H_ +#define _AT91SAM9N12_H_ + +/* + * Peripheral identifiers/interrupts. + */ +#define AT91SAM9N12_ID_PIOAB 2 /* Parallel I/O Controller A and B */ +#define AT91SAM9N12_ID_PIOCD 3 /* Parallel I/O Controller C and D */ +#define AT91SAM9N12_ID_FUSE 4 /* FUSE Controller */ +#define AT91SAM9N12_ID_USART0 5 /* USART 0 */ +#define AT91SAM9N12_ID_USART1 6 /* USART 1 */ +#define AT91SAM9N12_ID_USART2 7 /* USART 2 */ +#define AT91SAM9N12_ID_USART3 8 /* USART 3 */ +#define AT91SAM9N12_ID_TWI0 9 /* Two-Wire Interface 0 */ +#define AT91SAM9N12_ID_TWI1 10 /* Two-Wire Interface 1 */ +#define AT91SAM9N12_ID_MCI 12 /* High Speed Multimedia Card Interface */ +#define AT91SAM9N12_ID_SPI0 13 /* Serial Peripheral Interface 0 */ +#define AT91SAM9N12_ID_SPI1 14 /* Serial Peripheral Interface 1 */ +#define AT91SAM9N12_ID_UART0 15 /* UART 0 */ +#define AT91SAM9N12_ID_UART1 16 /* UART 1 */ +#define AT91SAM9N12_ID_TCB 17 /* Timer Counter 0, 1, 2, 3, 4 and 5 */ +#define AT91SAM9N12_ID_PWM 18 /* Pulse Width Modulation Controller */ +#define AT91SAM9N12_ID_ADC 19 /* ADC Controller */ +#define AT91SAM9N12_ID_DMA 20 /* DMA Controller */ +#define AT91SAM9N12_ID_UHP 22 /* USB Host High Speed */ +#define AT91SAM9N12_ID_UDP 23 /* USB Device High Speed */ +#define AT91SAM9N12_ID_LCDC 25 /* LCD Controller */ +#define AT91SAM9N12_ID_ISI 25 /* Image Sensor Interface */ +#define AT91SAM9N12_ID_SSC 28 /* Synchronous Serial Controller */ +#define AT91SAM9N12_ID_TRNG 30 /* TRNG */ +#define AT91SAM9N12_ID_IRQ0 31 /* Advanced Interrupt Controller */ + +/* + * User Peripheral physical base addresses. + */ +#define AT91SAM9N12_BASE_USART0 0xf801c000 +#define AT91SAM9N12_BASE_USART1 0xf8020000 +#define AT91SAM9N12_BASE_USART2 0xf8024000 +#define AT91SAM9N12_BASE_USART3 0xf8028000 + +/* + * Internal Memory. + */ +#define AT91SAM9N12_SRAM_BASE 0x00300000 /* Internal SRAM base address */ +#define AT91SAM9N12_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */ + +#define AT91SAM9N12_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91SAM9N12_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ + +#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h new file mode 100644 index 0000000..40060cd --- /dev/null +++ b/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h @@ -0,0 +1,53 @@ +/* + * Matrix-centric header file for the AT91SAM9N12 + * + * Copyright (C) 2012 Atmel Corporation. + * + * Only EBI related registers. + * Write Protect register definitions may be useful. + * + * Licensed under GPLv2 or later. + */ + +#ifndef _AT91SAM9N12_MATRIX_H_ +#define _AT91SAM9N12_MATRIX_H_ + +#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x118) /* EBI Chip Select Assignment Register */ +#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ +#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) +#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1) +#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */ +#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3) +#define AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH (1 << 3) +#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ +#define AT91_MATRIX_EBI_DBPU_ON (0 << 8) +#define AT91_MATRIX_EBI_DBPU_OFF (1 << 8) +#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */ +#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16) +#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16) +#define AT91_MATRIX_EBI_EBI_IOSR (1 << 17) /* EBI I/O slew rate selection */ +#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED (0 << 17) +#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL (1 << 17) +#define AT91_MATRIX_EBI_DDR_IOSR (1 << 18) /* DDR2 dedicated port I/O slew rate selection */ +#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18) +#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18) +#define AT91_MATRIX_NFD0_SELECT (1 << 24) /* NAND Flash Data Bus Selection */ +#define AT91_MATRIX_NFD0_ON_D0 (0 << 24) +#define AT91_MATRIX_NFD0_ON_D16 (1 << 24) +#define AT91_MATRIX_DDR_MP_EN (1 << 25) /* DDR Multi-port Enable */ +#define AT91_MATRIX_MP_OFF (0 << 25) +#define AT91_MATRIX_MP_ON (1 << 25) + +#define AT91_MATRIX_WPMR (AT91_MATRIX + 0x1E4) /* Write Protect Mode Register */ +#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */ +#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0) +#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0) +#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */ + +#define AT91_MATRIX_WPSR (AT91_MATRIX + 0x1E8) /* Write Protect Status Register */ +#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */ +#define AT91_MATRIX_WPSR_NO_WPV (0 << 0) +#define AT91_MATRIX_WPSR_WPV (1 << 0) +#define AT91_MATRIX_WPSR_WPVSRC (0xFFFF << 8) /* Write Protect Violation Source */ + +#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl.h b/arch/arm/mach-at91/include/mach/at91sam9rl.h index e0073eb..a15db56 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9rl.h +++ b/arch/arm/mach-at91/include/mach/at91sam9rl.h @@ -89,11 +89,6 @@ #define AT91SAM9RL_BASE_GPBR 0xfffffd60 #define AT91SAM9RL_BASE_RTC 0xfffffe00 -#define AT91_USART0 AT91SAM9RL_BASE_US0 -#define AT91_USART1 AT91SAM9RL_BASE_US1 -#define AT91_USART2 AT91SAM9RL_BASE_US2 -#define AT91_USART3 AT91SAM9RL_BASE_US3 - /* * Internal Memory. diff --git a/arch/arm/mach-at91/include/mach/at91sam9x5.h b/arch/arm/mach-at91/include/mach/at91sam9x5.h index 88e43d5..c75ee19 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9x5.h +++ b/arch/arm/mach-at91/include/mach/at91sam9x5.h @@ -55,14 +55,6 @@ #define AT91SAM9X5_BASE_USART2 0xf8024000 /* - * Base addresses for early serial code (uncompress.h) - */ -#define AT91_DBGU AT91_BASE_DBGU0 -#define AT91_USART0 AT91SAM9X5_BASE_USART0 -#define AT91_USART1 AT91SAM9X5_BASE_USART1 -#define AT91_USART2 AT91SAM9X5_BASE_USART2 - -/* * Internal Memory. */ #define AT91SAM9X5_SRAM_BASE 0x00300000 /* Internal SRAM base address */ diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h index 49a8211..369afc2 100644 --- a/arch/arm/mach-at91/include/mach/board.h +++ b/arch/arm/mach-at91/include/mach/board.h @@ -121,7 +121,6 @@ extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_de #define ATMEL_UART_RI 0x20 extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins); -extern void __init at91_set_serial_console(unsigned portnr); extern struct platform_device *atmel_default_console_device; diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h index 0118c33..b6504c1 100644 --- a/arch/arm/mach-at91/include/mach/cpu.h +++ b/arch/arm/mach-at91/include/mach/cpu.h @@ -25,6 +25,7 @@ #define ARCH_ID_AT91SAM9G45MRL 0x819b05a2 /* aka 9G45-ES2 & non ES lots */ #define ARCH_ID_AT91SAM9G45ES 0x819b05a1 /* 9G45-ES (Engineering Sample) */ #define ARCH_ID_AT91SAM9X5 0x819a05a0 +#define ARCH_ID_AT91SAM9N12 0x819a07a0 #define ARCH_ID_AT91SAM9XE128 0x329973a0 #define ARCH_ID_AT91SAM9XE256 0x329a93a0 @@ -54,6 +55,7 @@ #define ARCH_REVISON_9200_BGA (0 << 0) #define ARCH_REVISON_9200_PQFP (1 << 0) +#ifndef __ASSEMBLY__ enum at91_soc_type { /* 920T */ AT91_SOC_RM9200, @@ -70,6 +72,9 @@ enum at91_soc_type { /* SAM9X5 */ AT91_SOC_SAM9X5, + /* SAM9N12 */ + AT91_SOC_SAM9N12, + /* Unknown type */ AT91_SOC_NONE }; @@ -106,7 +111,7 @@ static inline int at91_soc_is_detected(void) return at91_soc_initdata.type != AT91_SOC_NONE; } -#ifdef CONFIG_ARCH_AT91RM9200 +#ifdef CONFIG_SOC_AT91RM9200 #define cpu_is_at91rm9200() (at91_soc_initdata.type == AT91_SOC_RM9200) #define cpu_is_at91rm9200_bga() (at91_soc_initdata.subtype == AT91_SOC_RM9200_BGA) #define cpu_is_at91rm9200_pqfp() (at91_soc_initdata.subtype == AT91_SOC_RM9200_PQFP) @@ -116,45 +121,37 @@ static inline int at91_soc_is_detected(void) #define cpu_is_at91rm9200_pqfp() (0) #endif -#ifdef CONFIG_ARCH_AT91SAM9260 +#ifdef CONFIG_SOC_AT91SAM9260 #define cpu_is_at91sam9xe() (at91_soc_initdata.subtype == AT91_SOC_SAM9XE) #define cpu_is_at91sam9260() (at91_soc_initdata.type == AT91_SOC_SAM9260) +#define cpu_is_at91sam9g20() (at91_soc_initdata.type == AT91_SOC_SAM9G20) #else #define cpu_is_at91sam9xe() (0) #define cpu_is_at91sam9260() (0) -#endif - -#ifdef CONFIG_ARCH_AT91SAM9G20 -#define cpu_is_at91sam9g20() (at91_soc_initdata.type == AT91_SOC_SAM9G20) -#else #define cpu_is_at91sam9g20() (0) #endif -#ifdef CONFIG_ARCH_AT91SAM9261 +#ifdef CONFIG_SOC_AT91SAM9261 #define cpu_is_at91sam9261() (at91_soc_initdata.type == AT91_SOC_SAM9261) -#else -#define cpu_is_at91sam9261() (0) -#endif - -#ifdef CONFIG_ARCH_AT91SAM9G10 #define cpu_is_at91sam9g10() (at91_soc_initdata.type == AT91_SOC_SAM9G10) #else +#define cpu_is_at91sam9261() (0) #define cpu_is_at91sam9g10() (0) #endif -#ifdef CONFIG_ARCH_AT91SAM9263 +#ifdef CONFIG_SOC_AT91SAM9263 #define cpu_is_at91sam9263() (at91_soc_initdata.type == AT91_SOC_SAM9263) #else #define cpu_is_at91sam9263() (0) #endif -#ifdef CONFIG_ARCH_AT91SAM9RL +#ifdef CONFIG_SOC_AT91SAM9RL #define cpu_is_at91sam9rl() (at91_soc_initdata.type == AT91_SOC_SAM9RL) #else #define cpu_is_at91sam9rl() (0) #endif -#ifdef CONFIG_ARCH_AT91SAM9G45 +#ifdef CONFIG_SOC_AT91SAM9G45 #define cpu_is_at91sam9g45() (at91_soc_initdata.type == AT91_SOC_SAM9G45) #define cpu_is_at91sam9g45es() (at91_soc_initdata.subtype == AT91_SOC_SAM9G45ES) #define cpu_is_at91sam9m10() (at91_soc_initdata.subtype == AT91_SOC_SAM9M10) @@ -168,7 +165,7 @@ static inline int at91_soc_is_detected(void) #define cpu_is_at91sam9m11() (0) #endif -#ifdef CONFIG_ARCH_AT91SAM9X5 +#ifdef CONFIG_SOC_AT91SAM9X5 #define cpu_is_at91sam9x5() (at91_soc_initdata.type == AT91_SOC_SAM9X5) #define cpu_is_at91sam9g15() (at91_soc_initdata.subtype == AT91_SOC_SAM9G15) #define cpu_is_at91sam9g35() (at91_soc_initdata.subtype == AT91_SOC_SAM9G35) @@ -184,10 +181,17 @@ static inline int at91_soc_is_detected(void) #define cpu_is_at91sam9x25() (0) #endif +#ifdef CONFIG_SOC_AT91SAM9N12 +#define cpu_is_at91sam9n12() (at91_soc_initdata.type == AT91_SOC_SAM9N12) +#else +#define cpu_is_at91sam9n12() (0) +#endif + /* * Since this is ARM, we will never run on any AVR32 CPU. But these * definitions may reduce clutter in common drivers. */ #define cpu_is_at32ap7000() (0) +#endif /* __ASSEMBLY__ */ #endif /* __MACH_CPU_H__ */ diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h index e9e29a6..09242b6 100644 --- a/arch/arm/mach-at91/include/mach/hardware.h +++ b/arch/arm/mach-at91/include/mach/hardware.h @@ -22,27 +22,18 @@ /* 9263, 9g45 */ #define AT91_BASE_DBGU1 0xffffee00 -#if defined(CONFIG_ARCH_AT91RM9200) +#if defined(CONFIG_ARCH_AT91X40) +#include <mach/at91x40.h> +#else #include <mach/at91rm9200.h> -#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #include <mach/at91sam9260.h> -#elif defined(CONFIG_ARCH_AT91SAM9261) || defined(CONFIG_ARCH_AT91SAM9G10) #include <mach/at91sam9261.h> -#elif defined(CONFIG_ARCH_AT91SAM9263) #include <mach/at91sam9263.h> -#elif defined(CONFIG_ARCH_AT91SAM9RL) #include <mach/at91sam9rl.h> -#elif defined(CONFIG_ARCH_AT91SAM9G45) #include <mach/at91sam9g45.h> -#elif defined(CONFIG_ARCH_AT91SAM9X5) #include <mach/at91sam9x5.h> -#elif defined(CONFIG_ARCH_AT91X40) -#include <mach/at91x40.h> -#else -#error "Unsupported AT91 processor" -#endif +#include <mach/at91sam9n12.h> -#if !defined(CONFIG_ARCH_AT91X40) /* * On all at91 except rm9200 and x40 have the System Controller starts * at address 0xffffc000 and has a size of 16KiB. @@ -94,7 +85,6 @@ * Virtual to Physical Address mapping for IO devices. */ #define AT91_VA_BASE_SYS AT91_IO_P2V(AT91_BASE_SYS) -#define AT91_VA_BASE_EMAC AT91_IO_P2V(AT91RM9200_BASE_EMAC) /* Internal SRAM is mapped below the IO devices */ #define AT91_SRAM_MAX SZ_1M diff --git a/arch/arm/mach-at91/include/mach/uncompress.h b/arch/arm/mach-at91/include/mach/uncompress.h index 4218647..6f6118d 100644 --- a/arch/arm/mach-at91/include/mach/uncompress.h +++ b/arch/arm/mach-at91/include/mach/uncompress.h @@ -1,7 +1,8 @@ /* * arch/arm/mach-at91/include/mach/uncompress.h * - * Copyright (C) 2003 SAN People + * Copyright (C) 2003 SAN People + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -25,22 +26,147 @@ #include <linux/atmel_serial.h> #include <mach/hardware.h> -#if defined(CONFIG_AT91_EARLY_DBGU0) -#define UART_OFFSET AT91_BASE_DBGU0 -#elif defined(CONFIG_AT91_EARLY_DBGU1) -#define UART_OFFSET AT91_BASE_DBGU1 -#elif defined(CONFIG_AT91_EARLY_USART0) -#define UART_OFFSET AT91_USART0 -#elif defined(CONFIG_AT91_EARLY_USART1) -#define UART_OFFSET AT91_USART1 -#elif defined(CONFIG_AT91_EARLY_USART2) -#define UART_OFFSET AT91_USART2 -#elif defined(CONFIG_AT91_EARLY_USART3) -#define UART_OFFSET AT91_USART3 -#elif defined(CONFIG_AT91_EARLY_USART4) -#define UART_OFFSET AT91_USART4 -#elif defined(CONFIG_AT91_EARLY_USART5) -#define UART_OFFSET AT91_USART5 +#include <mach/at91_dbgu.h> +#include <mach/cpu.h> + +void __iomem *at91_uart; + +#if !defined(CONFIG_ARCH_AT91X40) +static const u32 uarts_rm9200[] = { + AT91_BASE_DBGU0, + AT91RM9200_BASE_US0, + AT91RM9200_BASE_US1, + AT91RM9200_BASE_US2, + AT91RM9200_BASE_US3, + 0, +}; + +static const u32 uarts_sam9260[] = { + AT91_BASE_DBGU0, + AT91SAM9260_BASE_US0, + AT91SAM9260_BASE_US1, + AT91SAM9260_BASE_US2, + AT91SAM9260_BASE_US3, + AT91SAM9260_BASE_US4, + AT91SAM9260_BASE_US5, + 0, +}; + +static const u32 uarts_sam9261[] = { + AT91_BASE_DBGU0, + AT91SAM9261_BASE_US0, + AT91SAM9261_BASE_US1, + AT91SAM9261_BASE_US2, + 0, +}; + +static const u32 uarts_sam9263[] = { + AT91_BASE_DBGU1, + AT91SAM9263_BASE_US0, + AT91SAM9263_BASE_US1, + AT91SAM9263_BASE_US2, + 0, +}; + +static const u32 uarts_sam9g45[] = { + AT91_BASE_DBGU1, + AT91SAM9G45_BASE_US0, + AT91SAM9G45_BASE_US1, + AT91SAM9G45_BASE_US2, + AT91SAM9G45_BASE_US3, + 0, +}; + +static const u32 uarts_sam9rl[] = { + AT91_BASE_DBGU0, + AT91SAM9RL_BASE_US0, + AT91SAM9RL_BASE_US1, + AT91SAM9RL_BASE_US2, + AT91SAM9RL_BASE_US3, + 0, +}; + +static const u32 uarts_sam9x5[] = { + AT91_BASE_DBGU0, + AT91SAM9X5_BASE_USART0, + AT91SAM9X5_BASE_USART1, + AT91SAM9X5_BASE_USART2, + 0, +}; + +static inline const u32* decomp_soc_detect(u32 dbgu_base) +{ + u32 cidr, socid; + + cidr = __raw_readl(dbgu_base + AT91_DBGU_CIDR); + socid = cidr & ~AT91_CIDR_VERSION; + + switch (socid) { + case ARCH_ID_AT91RM9200: + return uarts_rm9200; + + case ARCH_ID_AT91SAM9G20: + case ARCH_ID_AT91SAM9260: + return uarts_sam9260; + + case ARCH_ID_AT91SAM9261: + return uarts_sam9261; + + case ARCH_ID_AT91SAM9263: + return uarts_sam9263; + + case ARCH_ID_AT91SAM9G45: + return uarts_sam9g45; + + case ARCH_ID_AT91SAM9RL64: + return uarts_sam9rl; + + case ARCH_ID_AT91SAM9X5: + return uarts_sam9x5; + } + + /* at91sam9g10 */ + if ((cidr & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) { + return uarts_sam9261; + } + /* at91sam9xe */ + else if ((cidr & AT91_CIDR_ARCH) == ARCH_FAMILY_AT91SAM9XE) { + return uarts_sam9260; + } + + return NULL; +} + +static inline void arch_decomp_setup(void) +{ + int i = 0; + const u32* usarts; + + usarts = decomp_soc_detect(AT91_BASE_DBGU0); + + if (!usarts) + usarts = decomp_soc_detect(AT91_BASE_DBGU1); + if (!usarts) { + at91_uart = NULL; + return; + } + + do { + /* physical address */ + at91_uart = (void __iomem *)usarts[i]; + + if (__raw_readl(at91_uart + ATMEL_US_BRGR)) + return; + i++; + } while (usarts[i]); + + at91_uart = NULL; +} +#else +static inline void arch_decomp_setup(void) +{ + at91_uart = NULL; +} #endif /* @@ -52,28 +178,24 @@ */ static void putc(int c) { -#ifdef UART_OFFSET - void __iomem *sys = (void __iomem *) UART_OFFSET; /* physical address */ + if (!at91_uart) + return; - while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXRDY)) + while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXRDY)) barrier(); - __raw_writel(c, sys + ATMEL_US_THR); -#endif + __raw_writel(c, at91_uart + ATMEL_US_THR); } static inline void flush(void) { -#ifdef UART_OFFSET - void __iomem *sys = (void __iomem *) UART_OFFSET; /* physical address */ + if (!at91_uart) + return; /* wait for transmission to complete */ - while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXEMPTY)) + while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXEMPTY)) barrier(); -#endif } -#define arch_decomp_setup() - #define arch_decomp_wdog() #endif diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index f630250..1bfaad6 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -261,7 +261,12 @@ static int at91_pm_enter(suspend_state_t state) * For ARM 926 based chips, this requirement is weaker * as at91sam9 can access a RAM in self-refresh mode. */ - at91_standby(); + if (cpu_is_at91rm9200()) + at91rm9200_standby(); + else if (cpu_is_at91sam9g45()) + at91sam9g45_standby(); + else + at91sam9_standby(); break; case PM_SUSPEND_ON: @@ -307,10 +312,9 @@ static int __init at91_pm_init(void) pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : "")); -#ifdef CONFIG_ARCH_AT91RM9200 /* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */ - at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0); -#endif + if (cpu_is_at91rm9200()) + at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0); suspend_set_ops(&at91_pm_ops); diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h index 89f56f3..38f467c 100644 --- a/arch/arm/mach-at91/pm.h +++ b/arch/arm/mach-at91/pm.h @@ -12,7 +12,6 @@ #define __ARCH_ARM_MACH_AT91_PM #include <mach/at91_ramc.h> -#ifdef CONFIG_ARCH_AT91RM9200 #include <mach/at91rm9200_sdramc.h> /* @@ -43,10 +42,6 @@ static inline void at91rm9200_standby(void) "r" (lpr)); } -#define at91_standby at91rm9200_standby - -#elif defined(CONFIG_ARCH_AT91SAM9G45) - /* We manage both DDRAM/SDRAM controllers, we need more than one value to * remember. */ @@ -75,11 +70,7 @@ static inline void at91sam9g45_standby(void) at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1); } -#define at91_standby at91sam9g45_standby - -#else - -#ifdef CONFIG_ARCH_AT91SAM9263 +#ifdef CONFIG_SOC_AT91SAM9263 /* * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use; * handle those cases both here and in the Suspend-To-RAM support. @@ -102,8 +93,4 @@ static inline void at91sam9_standby(void) at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr); } -#define at91_standby at91sam9_standby - -#endif - #endif diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S index db54521..098c28d 100644 --- a/arch/arm/mach-at91/pm_slowclock.S +++ b/arch/arm/mach-at91/pm_slowclock.S @@ -18,7 +18,7 @@ #include <mach/at91_ramc.h> -#ifdef CONFIG_ARCH_AT91SAM9263 +#ifdef CONFIG_SOC_AT91SAM9263 /* * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use; * handle those cases both here and in the Suspend-To-RAM support. diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index f44a2e7..944bffb 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -143,6 +143,11 @@ static void __init soc_detect(u32 dbgu_base) at91_soc_initdata.type = AT91_SOC_SAM9X5; at91_boot_soc = at91sam9x5_soc; break; + + case ARCH_ID_AT91SAM9N12: + at91_soc_initdata.type = AT91_SOC_SAM9N12; + at91_boot_soc = at91sam9n12_soc; + break; } /* at91sam9g10 */ @@ -210,6 +215,7 @@ static const char *soc_name[] = { [AT91_SOC_SAM9G45] = "at91sam9g45", [AT91_SOC_SAM9RL] = "at91sam9rl", [AT91_SOC_SAM9X5] = "at91sam9x5", + [AT91_SOC_SAM9N12] = "at91sam9n12", [AT91_SOC_NONE] = "Unknown" }; diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h index 5db4aa4..a9cfeb1 100644 --- a/arch/arm/mach-at91/soc.h +++ b/arch/arm/mach-at91/soc.h @@ -20,36 +20,41 @@ extern struct at91_init_soc at91sam9263_soc; extern struct at91_init_soc at91sam9g45_soc; extern struct at91_init_soc at91sam9rl_soc; extern struct at91_init_soc at91sam9x5_soc; +extern struct at91_init_soc at91sam9n12_soc; static inline int at91_soc_is_enabled(void) { return at91_boot_soc.init != NULL; } -#if !defined(CONFIG_ARCH_AT91RM9200) +#if !defined(CONFIG_SOC_AT91RM9200) #define at91rm9200_soc at91_boot_soc #endif -#if !(defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)) +#if !defined(CONFIG_SOC_AT91SAM9260) #define at91sam9260_soc at91_boot_soc #endif -#if !(defined(CONFIG_ARCH_AT91SAM9261) || defined(CONFIG_ARCH_AT91SAM9G10)) +#if !defined(CONFIG_SOC_AT91SAM9261) #define at91sam9261_soc at91_boot_soc #endif -#if !defined(CONFIG_ARCH_AT91SAM9263) +#if !defined(CONFIG_SOC_AT91SAM9263) #define at91sam9263_soc at91_boot_soc #endif -#if !defined(CONFIG_ARCH_AT91SAM9G45) +#if !defined(CONFIG_SOC_AT91SAM9G45) #define at91sam9g45_soc at91_boot_soc #endif -#if !defined(CONFIG_ARCH_AT91SAM9RL) +#if !defined(CONFIG_SOC_AT91SAM9RL) #define at91sam9rl_soc at91_boot_soc #endif -#if !defined(CONFIG_ARCH_AT91SAM9X5) +#if !defined(CONFIG_SOC_AT91SAM9X5) #define at91sam9x5_soc at91_boot_soc #endif + +#if !defined(CONFIG_SOC_AT91SAM9N12) +#define at91sam9n12_soc at91_boot_soc +#endif |