diff options
Diffstat (limited to 'arch/arm/mach-sa1100/assabet.c')
-rw-r--r-- | arch/arm/mach-sa1100/assabet.c | 185 |
1 files changed, 127 insertions, 58 deletions
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c index b5955ad..e708a93 100644 --- a/arch/arm/mach-sa1100/assabet.c +++ b/arch/arm/mach-sa1100/assabet.c @@ -21,6 +21,8 @@ #include <linux/delay.h> #include <linux/mm.h> +#include <video/sa1100fb.h> + #include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/irq.h> @@ -41,13 +43,13 @@ #include "generic.h" #define ASSABET_BCR_DB1110 \ - (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \ + (ASSABET_BCR_SPK_OFF | \ ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \ ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \ ASSABET_BCR_IRDA_MD0) #define ASSABET_BCR_DB1111 \ - (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \ + (ASSABET_BCR_SPK_OFF | \ ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \ ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \ ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \ @@ -77,34 +79,6 @@ static void assabet_ucb1x00_reset(enum ucb1x00_reset state) } -static void assabet_backlight_power(int on) -{ -#ifndef ASSABET_PAL_VIDEO - if (on) - ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON); - else -#endif - ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON); -} - -/* - * Turn on/off the backlight. When turning the backlight on, - * we wait 500us after turning it on so we don't cause the - * supplies to droop when we enable the LCD controller (and - * cause a hard reset.) - */ -static void assabet_lcd_power(int on) -{ -#ifndef ASSABET_PAL_VIDEO - if (on) { - ASSABET_BCR_set(ASSABET_BCR_LCD_ON); - udelay(500); - } else -#endif - ASSABET_BCR_clear(ASSABET_BCR_LCD_ON); -} - - /* * Assabet flash support code. */ @@ -160,15 +134,8 @@ static struct flash_platform_data assabet_flash_data = { }; static struct resource assabet_flash_resources[] = { - { - .start = SA1100_CS0_PHYS, - .end = SA1100_CS0_PHYS + SZ_32M - 1, - .flags = IORESOURCE_MEM, - }, { - .start = SA1100_CS1_PHYS, - .end = SA1100_CS1_PHYS + SZ_32M - 1, - .flags = IORESOURCE_MEM, - } + DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M), + DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M), }; @@ -218,13 +185,115 @@ static struct mcp_plat_data assabet_mcp_data = { .codec_pdata = &assabet_ucb1x00_data, }; +static void assabet_lcd_set_visual(u32 visual) +{ + u_int is_true_color = visual == FB_VISUAL_TRUECOLOR; + + if (machine_is_assabet()) { +#if 1 // phase 4 or newer Assabet's + if (is_true_color) + ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB); + else + ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB); +#else + // older Assabet's + if (is_true_color) + ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB); + else + ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB); +#endif + } +} + +#ifndef ASSABET_PAL_VIDEO +static void assabet_lcd_backlight_power(int on) +{ + if (on) + ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON); + else + ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON); +} + +/* + * Turn on/off the backlight. When turning the backlight on, we wait + * 500us after turning it on so we don't cause the supplies to droop + * when we enable the LCD controller (and cause a hard reset.) + */ +static void assabet_lcd_power(int on) +{ + if (on) { + ASSABET_BCR_set(ASSABET_BCR_LCD_ON); + udelay(500); + } else + ASSABET_BCR_clear(ASSABET_BCR_LCD_ON); +} + +/* + * The assabet uses a sharp LQ039Q2DS54 LCD module. It is actually + * takes an RGB666 signal, but we provide it with an RGB565 signal + * instead (def_rgb_16). + */ +static struct sa1100fb_mach_info lq039q2ds54_info = { + .pixclock = 171521, .bpp = 16, + .xres = 320, .yres = 240, + + .hsync_len = 5, .vsync_len = 1, + .left_margin = 61, .upper_margin = 3, + .right_margin = 9, .lower_margin = 0, + + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + + .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act, + .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2), + + .backlight_power = assabet_lcd_backlight_power, + .lcd_power = assabet_lcd_power, + .set_visual = assabet_lcd_set_visual, +}; +#else +static void assabet_pal_backlight_power(int on) +{ + ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON); +} + +static void assabet_pal_power(int on) +{ + ASSABET_BCR_clear(ASSABET_BCR_LCD_ON); +} + +static struct sa1100fb_mach_info pal_info = { + .pixclock = 67797, .bpp = 16, + .xres = 640, .yres = 512, + + .hsync_len = 64, .vsync_len = 6, + .left_margin = 125, .upper_margin = 70, + .right_margin = 115, .lower_margin = 36, + + .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act, + .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512), + + .backlight_power = assabet_pal_backlight_power, + .lcd_power = assabet_pal_power, + .set_visual = assabet_lcd_set_visual, +}; +#endif + +#ifdef CONFIG_ASSABET_NEPONSET +static struct resource neponset_resources[] = { + DEFINE_RES_MEM(0x10000000, 0x08000000), + DEFINE_RES_MEM(0x18000000, 0x04000000), + DEFINE_RES_MEM(0x40000000, SZ_8K), + DEFINE_RES_IRQ(IRQ_GPIO25), +}; +#endif + static void __init assabet_init(void) { /* * Ensure that the power supply is in "high power" mode. */ - GPDR |= GPIO_GPIO16; GPSR = GPIO_GPIO16; + GPDR |= GPIO_GPIO16; /* * Ensure that these pins are set as outputs and are driving @@ -232,8 +301,16 @@ static void __init assabet_init(void) * the WS latch in the CPLD, and we don't float causing * excessive power drain. --rmk */ - GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; + GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; + + /* + * Also set GPIO27 as an output; this is used to clock UART3 + * via the FPGA and as otherwise has no pullups or pulldowns, + * so stop it floating. + */ + GPCR = GPIO_GPIO27; + GPDR |= GPIO_GPIO27; /* * Set up registers for sleep mode. @@ -247,9 +324,6 @@ static void __init assabet_init(void) sa11x0_ppc_configure_mcp(); - sa1100fb_lcd_power = assabet_lcd_power; - sa1100fb_backlight_power = assabet_backlight_power; - if (machine_has_neponset()) { /* * Angel sets this, but other bootloaders may not. @@ -262,9 +336,17 @@ static void __init assabet_init(void) #ifndef CONFIG_ASSABET_NEPONSET printk( "Warning: Neponset detected but full support " "hasn't been configured in the kernel\n" ); +#else + platform_device_register_simple("neponset", 0, + neponset_resources, ARRAY_SIZE(neponset_resources)); #endif } +#ifndef ASSABET_PAL_VIDEO + sa11x0_register_lcd(&lq039q2ds54_info); +#else + sa11x0_register_lcd(&pal_video); +#endif sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources, ARRAY_SIZE(assabet_flash_resources)); sa11x0_register_irda(&assabet_irda_data); @@ -428,21 +510,8 @@ static void __init assabet_map_io(void) */ Ser1SDCR0 |= SDCR0_SUS; - if (machine_has_neponset()) { -#ifdef CONFIG_ASSABET_NEPONSET - extern void neponset_map_io(void); - - /* - * We map Neponset registers even if it isn't present since - * many drivers will try to probe their stuff (and fail). - * This is still more friendly than a kernel paging request - * crash. - */ - neponset_map_io(); -#endif - } else { + if (!machine_has_neponset()) sa1100_register_uart_fns(&assabet_port_fns); - } /* * When Neponset is attached, the first UART should be |