diff options
Diffstat (limited to 'drivers/net/ethernet/i825xx/lib82596.c')
| -rw-r--r-- | drivers/net/ethernet/i825xx/lib82596.c | 1412 |
1 files changed, 1412 insertions, 0 deletions
diff --git a/drivers/net/ethernet/i825xx/lib82596.c b/drivers/net/ethernet/i825xx/lib82596.c new file mode 100644 index 0000000..9e04289 --- /dev/null +++ b/drivers/net/ethernet/i825xx/lib82596.c @@ -0,0 +1,1412 @@ +/* lasi_82596.c -- driver for the intel 82596 ethernet controller, as + munged into HPPA boxen . + + This driver is based upon 82596.c, original credits are below... + but there were too many hoops which HP wants jumped through to + keep this code in there in a sane manner. + + 3 primary sources of the mess -- + 1) hppa needs *lots* of cacheline flushing to keep this kind of + MMIO running. + + 2) The 82596 needs to see all of its pointers as their physical + address. Thus virt_to_bus/bus_to_virt are *everywhere*. + + 3) The implementation HP is using seems to be significantly pickier + about when and how the command and RX units are started. some + command ordering was changed. + + Examination of the mach driver leads one to believe that there + might be a saner way to pull this off... anyone who feels like a + full rewrite can be my guest. + + Split 02/13/2000 Sam Creasey (sammy@oh.verio.com) + + 02/01/2000 Initial modifications for parisc by Helge Deller (deller@gmx.de) + 03/02/2000 changes for better/correct(?) cache-flushing (deller) +*/ + +/* 82596.c: A generic 82596 ethernet driver for linux. */ +/* + Based on Apricot.c + Written 1994 by Mark Evans. + This driver is for the Apricot 82596 bus-master interface + + Modularised 12/94 Mark Evans + + + Modified to support the 82596 ethernet chips on 680x0 VME boards. + by Richard Hirst <richard@sleepie.demon.co.uk> + Renamed to be 82596.c + + 980825: Changed to receive directly in to sk_buffs which are + allocated at open() time. Eliminates copy on incoming frames + (small ones are still copied). Shared data now held in a + non-cached page, so we can run on 68060 in copyback mode. + + TBD: + * look at deferring rx frames rather than discarding (as per tulip) + * handle tx ring full as per tulip + * performance test to tune rx_copybreak + + Most of my modifications relate to the braindead big-endian + implementation by Intel. When the i596 is operating in + 'big-endian' mode, it thinks a 32 bit value of 0x12345678 + should be stored as 0x56781234. This is a real pain, when + you have linked lists which are shared by the 680x0 and the + i596. + + Driver skeleton + Written 1993 by Donald Becker. + Copyright 1993 United States Government as represented by the Director, + National Security Agency. This software may only be used and distributed + according to the terms of the GNU General Public License as modified by SRC, + incorporated herein by reference. + + The author may be reached as becker@scyld.com, or C/O + Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 + + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/bitops.h> +#include <linux/dma-mapping.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/gfp.h> + +/* DEBUG flags + */ + +#define DEB_INIT 0x0001 +#define DEB_PROBE 0x0002 +#define DEB_SERIOUS 0x0004 +#define DEB_ERRORS 0x0008 +#define DEB_MULTI 0x0010 +#define DEB_TDR 0x0020 +#define DEB_OPEN 0x0040 +#define DEB_RESET 0x0080 +#define DEB_ADDCMD 0x0100 +#define DEB_STATUS 0x0200 +#define DEB_STARTTX 0x0400 +#define DEB_RXADDR 0x0800 +#define DEB_TXADDR 0x1000 +#define DEB_RXFRAME 0x2000 +#define DEB_INTS 0x4000 +#define DEB_STRUCT 0x8000 +#define DEB_ANY 0xffff + + +#define DEB(x, y) if (i596_debug & (x)) { y; } + + +/* + * The MPU_PORT command allows direct access to the 82596. With PORT access + * the following commands are available (p5-18). The 32-bit port command + * must be word-swapped with the most significant word written first. + * This only applies to VME boards. + */ +#define PORT_RESET 0x00 /* reset 82596 */ +#define PORT_SELFTEST 0x01 /* selftest */ +#define PORT_ALTSCP 0x02 /* alternate SCB address */ +#define PORT_ALTDUMP 0x03 /* Alternate DUMP address */ + +static int i596_debug = (DEB_SERIOUS|DEB_PROBE); + +/* Copy frames shorter than rx_copybreak, otherwise pass on up in + * a full sized sk_buff. Value of 100 stolen from tulip.c (!alpha). + */ +static int rx_copybreak = 100; + +#define PKT_BUF_SZ 1536 +#define MAX_MC_CNT 64 + +#define ISCP_BUSY 0x0001 + +#define I596_NULL ((u32)0xffffffff) + +#define CMD_EOL 0x8000 /* The last command of the list, stop. */ +#define CMD_SUSP 0x4000 /* Suspend after doing cmd. */ +#define CMD_INTR 0x2000 /* Interrupt after doing cmd. */ + +#define CMD_FLEX 0x0008 /* Enable flexible memory model */ + +enum commands { + CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3, + CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7 +}; + +#define STAT_C 0x8000 /* Set to 0 after execution */ +#define STAT_B 0x4000 /* Command being executed */ +#define STAT_OK 0x2000 /* Command executed ok */ +#define STAT_A 0x1000 /* Command aborted */ + +#define CUC_START 0x0100 +#define CUC_RESUME 0x0200 +#define CUC_SUSPEND 0x0300 +#define CUC_ABORT 0x0400 +#define RX_START 0x0010 +#define RX_RESUME 0x0020 +#define RX_SUSPEND 0x0030 +#define RX_ABORT 0x0040 + +#define TX_TIMEOUT (HZ/20) + + +struct i596_reg { + unsigned short porthi; + unsigned short portlo; + u32 ca; +}; + +#define EOF 0x8000 +#define SIZE_MASK 0x3fff + +struct i596_tbd { + unsigned short size; + unsigned short pad; + u32 next; + u32 data; + u32 cache_pad[5]; /* Total 32 bytes... */ +}; + +/* The command structure has two 'next' pointers; v_next is the address of + * the next command as seen by the CPU, b_next is the address of the next + * command as seen by the 82596. The b_next pointer, as used by the 82596 + * always references the status field of the next command, rather than the + * v_next field, because the 82596 is unaware of v_next. It may seem more + * logical to put v_next at the end of the structure, but we cannot do that + * because the 82596 expects other fields to be there, depending on command + * type. + */ + +struct i596_cmd { + struct i596_cmd *v_next; /* Address from CPUs viewpoint */ + unsigned short status; + unsigned short command; + u32 b_next; /* Address from i596 viewpoint */ +}; + +struct tx_cmd { + struct i596_cmd cmd; + u32 tbd; + unsigned short size; + unsigned short pad; + struct sk_buff *skb; /* So we can free it after tx */ + dma_addr_t dma_addr; +#ifdef __LP64__ + u32 cache_pad[6]; /* Total 64 bytes... */ +#else + u32 cache_pad[1]; /* Total 32 bytes... */ +#endif +}; + +struct tdr_cmd { + struct i596_cmd cmd; + unsigned short status; + unsigned short pad; +}; + +struct mc_cmd { + struct i596_cmd cmd; + short mc_cnt; + char mc_addrs[MAX_MC_CNT*6]; +}; + +struct sa_cmd { + struct i596_cmd cmd; + char eth_addr[8]; +}; + +struct cf_cmd { + struct i596_cmd cmd; + char i596_config[16]; +}; + +struct i596_rfd { + unsigned short stat; + unsigned short cmd; + u32 b_next; /* Address from i596 viewpoint */ + u32 rbd; + unsigned short count; + unsigned short size; + struct i596_rfd *v_next; /* Address from CPUs viewpoint */ + struct i596_rfd *v_prev; +#ifndef __LP64__ + u32 cache_pad[2]; /* Total 32 bytes... */ +#endif +}; + +struct i596_rbd { + /* hardware data */ + unsigned short count; + unsigned short zero1; + u32 b_next; + u32 b_data; /* Address from i596 viewpoint */ + unsigned short size; + unsigned short zero2; + /* driver data */ + struct sk_buff *skb; + struct i596_rbd *v_next; + u32 b_addr; /* This rbd addr from i596 view */ + unsigned char *v_data; /* Address from CPUs viewpoint */ + /* Total 32 bytes... */ +#ifdef __LP64__ + u32 cache_pad[4]; +#endif +}; + +/* These values as chosen so struct i596_dma fits in one page... */ + +#define TX_RING_SIZE 32 +#define RX_RING_SIZE 16 + +struct i596_scb { + unsigned short status; + unsigned short command; + u32 cmd; + u32 rfd; + u32 crc_err; + u32 align_err; + u32 resource_err; + u32 over_err; + u32 rcvdt_err; + u32 short_err; + unsigned short t_on; + unsigned short t_off; +}; + +struct i596_iscp { + u32 stat; + u32 scb; +}; + +struct i596_scp { + u32 sysbus; + u32 pad; + u32 iscp; +}; + +struct i596_dma { + struct i596_scp scp __attribute__((aligned(32))); + volatile struct i596_iscp iscp __attribute__((aligned(32))); + volatile struct i596_scb scb __attribute__((aligned(32))); + struct sa_cmd sa_cmd __attribute__((aligned(32))); + struct cf_cmd cf_cmd __attribute__((aligned(32))); + struct tdr_cmd tdr_cmd __attribute__((aligned(32))); + struct mc_cmd mc_cmd __attribute__((aligned(32))); + struct i596_rfd rfds[RX_RING_SIZE] __attribute__((aligned(32))); + struct i596_rbd rbds[RX_RING_SIZE] __attribute__((aligned(32))); + struct tx_cmd tx_cmds[TX_RING_SIZE] __attribute__((aligned(32))); + struct i596_tbd tbds[TX_RING_SIZE] __attribute__((aligned(32))); +}; + +struct i596_private { + struct i596_dma *dma; + u32 stat; + int last_restart; + struct i596_rfd *rfd_head; + struct i596_rbd *rbd_head; + struct i596_cmd *cmd_tail; + struct i596_cmd *cmd_head; + int cmd_backlog; + u32 last_cmd; + int next_tx_cmd; + int options; + spinlock_t lock; /* serialize access to chip */ + dma_addr_t dma_addr; + void __iomem *mpu_port; + void __iomem *ca; +}; + +static const char init_setup[] = +{ + 0x8E, /* length, prefetch on */ + 0xC8, /* fifo to 8, monitor off */ + 0x80, /* don't save bad frames */ + 0x2E, /* No source address insertion, 8 byte preamble */ + 0x00, /* priority and backoff defaults */ + 0x60, /* interframe spacing */ + 0x00, /* slot time LSB */ + 0xf2, /* slot time and retries */ + 0x00, /* promiscuous mode */ + 0x00, /* collision detect */ + 0x40, /* minimum frame length */ + 0xff, + 0x00, + 0x7f /* *multi IA */ }; + +static int i596_open(struct net_device *dev); +static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev); +static irqreturn_t i596_interrupt(int irq, void *dev_id); +static int i596_close(struct net_device *dev); +static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd); +static void i596_tx_timeout (struct net_device *dev); +static void print_eth(unsigned char *buf, char *str); +static void set_multicast_list(struct net_device *dev); +static inline void ca(struct net_device *dev); +static void mpu_port(struct net_device *dev, int c, dma_addr_t x); + +static int rx_ring_size = RX_RING_SIZE; +static int ticks_limit = 100; +static int max_cmd_backlog = TX_RING_SIZE-1; + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void i596_poll_controller(struct net_device *dev); +#endif + + +static inline int wait_istat(struct net_device *dev, struct i596_dma *dma, int delcnt, char *str) +{ + DMA_INV(dev, &(dma->iscp), sizeof(struct i596_iscp)); + while (--delcnt && dma->iscp.stat) { + udelay(10); + DMA_INV(dev, &(dma->iscp), sizeof(struct i596_iscp)); + } + if (!delcnt) { + printk(KERN_ERR "%s: %s, iscp.stat %04x, didn't clear\n", + dev->name, str, SWAP16(dma->iscp.stat)); + return -1; + } else + return 0; +} + + +static inline int wait_cmd(struct net_device *dev, struct i596_dma *dma, int delcnt, char *str) +{ + DMA_INV(dev, &(dma->scb), sizeof(struct i596_scb)); + while (--delcnt && dma->scb.command) { + udelay(10); + DMA_INV(dev, &(dma->scb), sizeof(struct i596_scb)); + } + if (!delcnt) { + printk(KERN_ERR "%s: %s, status %4.4x, cmd %4.4x.\n", + dev->name, str, + SWAP16(dma->scb.status), + SWAP16(dma->scb.command)); + return -1; + } else + return 0; +} + + +static void i596_display_data(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + struct i596_cmd *cmd; + struct i596_rfd *rfd; + struct i596_rbd *rbd; + + printk(KERN_DEBUG "lp and scp at %p, .sysbus = %08x, .iscp = %08x\n", + &dma->scp, dma->scp.sysbus, SWAP32(dma->scp.iscp)); + printk(KERN_DEBUG "iscp at %p, iscp.stat = %08x, .scb = %08x\n", + &dma->iscp, SWAP32(dma->iscp.stat), SWAP32(dma->iscp.scb)); + printk(KERN_DEBUG "scb at %p, scb.status = %04x, .command = %04x," + " .cmd = %08x, .rfd = %08x\n", + &dma->scb, SWAP16(dma->scb.status), SWAP16(dma->scb.command), + SWAP16(dma->scb.cmd), SWAP32(dma->scb.rfd)); + printk(KERN_DEBUG " errors: crc %x, align %x, resource %x," + " over %x, rcvdt %x, short %x\n", + SWAP32(dma->scb.crc_err), SWAP32(dma->scb.align_err), + SWAP32(dma->scb.resource_err), SWAP32(dma->scb.over_err), + SWAP32(dma->scb.rcvdt_err), SWAP32(dma->scb.short_err)); + cmd = lp->cmd_head; + while (cmd != NULL) { + printk(KERN_DEBUG + "cmd at %p, .status = %04x, .command = %04x," + " .b_next = %08x\n", + cmd, SWAP16(cmd->status), SWAP16(cmd->command), + SWAP32(cmd->b_next)); + cmd = cmd->v_next; + } + rfd = lp->rfd_head; + printk(KERN_DEBUG "rfd_head = %p\n", rfd); + do { + printk(KERN_DEBUG + " %p .stat %04x, .cmd %04x, b_next %08x, rbd %08x," + " count %04x\n", + rfd, SWAP16(rfd->stat), SWAP16(rfd->cmd), + SWAP32(rfd->b_next), SWAP32(rfd->rbd), + SWAP16(rfd->count)); + rfd = rfd->v_next; + } while (rfd != lp->rfd_head); + rbd = lp->rbd_head; + printk(KERN_DEBUG "rbd_head = %p\n", rbd); + do { + printk(KERN_DEBUG + " %p .count %04x, b_next %08x, b_data %08x," + " size %04x\n", + rbd, SWAP16(rbd->count), SWAP32(rbd->b_next), + SWAP32(rbd->b_data), SWAP16(rbd->size)); + rbd = rbd->v_next; + } while (rbd != lp->rbd_head); + DMA_INV(dev, dma, sizeof(struct i596_dma)); +} + + +#define virt_to_dma(lp, v) ((lp)->dma_addr + (dma_addr_t)((unsigned long)(v)-(unsigned long)((lp)->dma))) + +static inline int init_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int i; + struct i596_rfd *rfd; + struct i596_rbd *rbd; + + /* First build the Receive Buffer Descriptor List */ + + for (i = 0, rbd = dma->rbds; i < rx_ring_size; i++, rbd++) { + dma_addr_t dma_addr; + struct sk_buff *skb; + + skb = netdev_alloc_skb_ip_align(dev, PKT_BUF_SZ); + if (skb == NULL) + return -1; + dma_addr = dma_map_single(dev->dev.parent, skb->data, + PKT_BUF_SZ, DMA_FROM_DEVICE); + rbd->v_next = rbd+1; + rbd->b_next = SWAP32(virt_to_dma(lp, rbd+1)); + rbd->b_addr = SWAP32(virt_to_dma(lp, rbd)); + rbd->skb = skb; + rbd->v_data = skb->data; + rbd->b_data = SWAP32(dma_addr); + rbd->size = SWAP16(PKT_BUF_SZ); + } + lp->rbd_head = dma->rbds; + rbd = dma->rbds + rx_ring_size - 1; + rbd->v_next = dma->rbds; + rbd->b_next = SWAP32(virt_to_dma(lp, dma->rbds)); + + /* Now build the Receive Frame Descriptor List */ + + for (i = 0, rfd = dma->rfds; i < rx_ring_size; i++, rfd++) { + rfd->rbd = I596_NULL; + rfd->v_next = rfd+1; + rfd->v_prev = rfd-1; + rfd->b_next = SWAP32(virt_to_dma(lp, rfd+1)); + rfd->cmd = SWAP16(CMD_FLEX); + } + lp->rfd_head = dma->rfds; + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + rfd = dma->rfds; + rfd->rbd = SWAP32(virt_to_dma(lp, lp->rbd_head)); + rfd->v_prev = dma->rfds + rx_ring_size - 1; + rfd = dma->rfds + rx_ring_size - 1; + rfd->v_next = dma->rfds; + rfd->b_next = SWAP32(virt_to_dma(lp, dma->rfds)); + rfd->cmd = SWAP16(CMD_EOL|CMD_FLEX); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); + return 0; +} + +static inline void remove_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_rbd *rbd; + int i; + + for (i = 0, rbd = lp->dma->rbds; i < rx_ring_size; i++, rbd++) { + if (rbd->skb == NULL) + break; + dma_unmap_single(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + dev_kfree_skb(rbd->skb); + } +} + + +static void rebuild_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int i; + + /* Ensure rx frame/buffer descriptors are tidy */ + + for (i = 0; i < rx_ring_size; i++) { + dma->rfds[i].rbd = I596_NULL; + dma->rfds[i].cmd = SWAP16(CMD_FLEX); + } + dma->rfds[rx_ring_size-1].cmd = SWAP16(CMD_EOL|CMD_FLEX); + lp->rfd_head = dma->rfds; + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + lp->rbd_head = dma->rbds; + dma->rfds[0].rbd = SWAP32(virt_to_dma(lp, dma->rbds)); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); +} + + +static int init_i596_mem(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + unsigned long flags; + + mpu_port(dev, PORT_RESET, 0); + udelay(100); /* Wait 100us - seems to help */ + + /* change the scp address */ + + lp->last_cmd = jiffies; + + dma->scp.sysbus = SYSBUS; + dma->scp.iscp = SWAP32(virt_to_dma(lp, &(dma->iscp))); + dma->iscp.scb = SWAP32(virt_to_dma(lp, &(dma->scb))); + dma->iscp.stat = SWAP32(ISCP_BUSY); + lp->cmd_backlog = 0; + + lp->cmd_head = NULL; + dma->scb.cmd = I596_NULL; + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: starting i82596.\n", dev->name)); + + DMA_WBACK(dev, &(dma->scp), sizeof(struct i596_scp)); + DMA_WBACK(dev, &(dma->iscp), sizeof(struct i596_iscp)); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + mpu_port(dev, PORT_ALTSCP, virt_to_dma(lp, &dma->scp)); + ca(dev); + if (wait_istat(dev, dma, 1000, "initialization timed out")) + goto failed; + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: i82596 initialization successful\n", + dev->name)); + + if (request_irq(dev->irq, i596_interrupt, 0, "i82596", dev)) { + printk(KERN_ERR "%s: IRQ %d not free\n", dev->name, dev->irq); + goto failed; + } + + /* Ensure rx frame/buffer descriptors are tidy */ + rebuild_rx_bufs(dev); + + dma->scb.command = 0; + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: queuing CmdConfigure\n", dev->name)); + memcpy(dma->cf_cmd.i596_config, init_setup, 14); + dma->cf_cmd.cmd.command = SWAP16(CmdConfigure); + DMA_WBACK(dev, &(dma->cf_cmd), sizeof(struct cf_cmd)); + i596_add_cmd(dev, &dma->cf_cmd.cmd); + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: queuing CmdSASetup\n", dev->name)); + memcpy(dma->sa_cmd.eth_addr, dev->dev_addr, 6); + dma->sa_cmd.cmd.command = SWAP16(CmdSASetup); + DMA_WBACK(dev, &(dma->sa_cmd), sizeof(struct sa_cmd)); + i596_add_cmd(dev, &dma->sa_cmd.cmd); + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: queuing CmdTDR\n", dev->name)); + dma->tdr_cmd.cmd.command = SWAP16(CmdTDR); + DMA_WBACK(dev, &(dma->tdr_cmd), sizeof(struct tdr_cmd)); + i596_add_cmd(dev, &dma->tdr_cmd.cmd); + + spin_lock_irqsave (&lp->lock, flags); + + if (wait_cmd(dev, dma, 1000, "timed out waiting to issue RX_START")) { + spin_unlock_irqrestore (&lp->lock, flags); + goto failed_free_irq; + } + DEB(DEB_INIT, printk(KERN_DEBUG "%s: Issuing RX_START\n", dev->name)); + dma->scb.command = SWAP16(RX_START); + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + ca(dev); + + spin_unlock_irqrestore (&lp->lock, flags); + if (wait_cmd(dev, dma, 1000, "RX_START not processed")) + goto failed_free_irq; + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: Receive unit started OK\n", dev->name)); + return 0; + +failed_free_irq: + free_irq(dev->irq, dev); +failed: + printk(KERN_ERR "%s: Failed to initialise 82596\n", dev->name); + mpu_port(dev, PORT_RESET, 0); + return -1; +} + + +static inline int i596_rx(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_rfd *rfd; + struct i596_rbd *rbd; + int frames = 0; + + DEB(DEB_RXFRAME, printk(KERN_DEBUG + "i596_rx(), rfd_head %p, rbd_head %p\n", + lp->rfd_head, lp->rbd_head)); + + + rfd = lp->rfd_head; /* Ref next frame to check */ + + DMA_INV(dev, rfd, sizeof(struct i596_rfd)); + while (rfd->stat & SWAP16(STAT_C)) { /* Loop while complete frames */ + if (rfd->rbd == I596_NULL) + rbd = NULL; + else if (rfd->rbd == lp->rbd_head->b_addr) { + rbd = lp->rbd_head; + DMA_INV(dev, rbd, sizeof(struct i596_rbd)); + } else { + printk(KERN_ERR "%s: rbd chain broken!\n", dev->name); + /* XXX Now what? */ + rbd = NULL; + } + DEB(DEB_RXFRAME, printk(KERN_DEBUG + " rfd %p, rfd.rbd %08x, rfd.stat %04x\n", + rfd, rfd->rbd, rfd->stat)); + + if (rbd != NULL && (rfd->stat & SWAP16(STAT_OK))) { + /* a good frame */ + int pkt_len = SWAP16(rbd->count) & 0x3fff; + struct sk_buff *skb = rbd->skb; + int rx_in_place = 0; + + DEB(DEB_RXADDR, print_eth(rbd->v_data, "received")); + frames++; + + /* Check if the packet is long enough to just accept + * without copying to a properly sized skbuff. + */ + + if (pkt_len > rx_copybreak) { + struct sk_buff *newskb; + dma_addr_t dma_addr; + + dma_unmap_single(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + /* Get fresh skbuff to replace filled one. */ + newskb = netdev_alloc_skb_ip_align(dev, + PKT_BUF_SZ); + if (newskb == NULL) { + skb = NULL; /* drop pkt */ + goto memory_squeeze; + } + + /* Pass up the skb already on the Rx ring. */ + skb_put(skb, pkt_len); + rx_in_place = 1; + rbd->skb = newskb; + dma_addr = dma_map_single(dev->dev.parent, + newskb->data, + PKT_BUF_SZ, + DMA_FROM_DEVICE); + rbd->v_data = newskb->data; + rbd->b_data = SWAP32(dma_addr); + DMA_WBACK_INV(dev, rbd, sizeof(struct i596_rbd)); + } else + skb = netdev_alloc_skb_ip_align(dev, pkt_len); +memory_squeeze: + if (skb == NULL) { + /* XXX tulip.c can defer packets here!! */ + printk(KERN_ERR + "%s: i596_rx Memory squeeze, dropping packet.\n", + dev->name); + dev->stats.rx_dropped++; + } else { + if (!rx_in_place) { + /* 16 byte align the data fields */ + dma_sync_single_for_cpu(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + memcpy(skb_put(skb, pkt_len), rbd->v_data, pkt_len); + dma_sync_single_for_device(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + } + skb->len = pkt_len; + skb->protocol = eth_type_trans(skb, dev); + netif_rx(skb); + dev->stats.rx_packets++; + dev->stats.rx_bytes += pkt_len; + } + } else { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: Error, rfd.stat = 0x%04x\n", + dev->name, rfd->stat)); + dev->stats.rx_errors++; + if (rfd->stat & SWAP16(0x0100)) + dev->stats.collisions++; + if (rfd->stat & SWAP16(0x8000)) + dev->stats.rx_length_errors++; + if (rfd->stat & SWAP16(0x0001)) + dev->stats.rx_over_errors++; + if (rfd->stat & SWAP16(0x0002)) + dev->stats.rx_fifo_errors++; + if (rfd->stat & SWAP16(0x0004)) + dev->stats.rx_frame_errors++; + if (rfd->stat & SWAP16(0x0008)) + dev->stats.rx_crc_errors++; + if (rfd->stat & SWAP16(0x0010)) + dev->stats.rx_length_errors++; + } + + /* Clear the buffer descriptor count and EOF + F flags */ + + if (rbd != NULL && (rbd->count & SWAP16(0x4000))) { + rbd->count = 0; + lp->rbd_head = rbd->v_next; + DMA_WBACK_INV(dev, rbd, sizeof(struct i596_rbd)); + } + + /* Tidy the frame descriptor, marking it as end of list */ + + rfd->rbd = I596_NULL; + rfd->stat = 0; + rfd->cmd = SWAP16(CMD_EOL|CMD_FLEX); + rfd->count = 0; + + /* Update record of next frame descriptor to process */ + + lp->dma->scb.rfd = rfd->b_next; + lp->rfd_head = rfd->v_next; + DMA_WBACK_INV(dev, rfd, sizeof(struct i596_rfd)); + + /* Remove end-of-list from old end descriptor */ + + rfd->v_prev->cmd = SWAP16(CMD_FLEX); + DMA_WBACK_INV(dev, rfd->v_prev, sizeof(struct i596_rfd)); + rfd = lp->rfd_head; + DMA_INV(dev, rfd, sizeof(struct i596_rfd)); + } + + DEB(DEB_RXFRAME, printk(KERN_DEBUG "frames %d\n", frames)); + + return 0; +} + + +static inline void i596_cleanup_cmd(struct net_device *dev, struct i596_private *lp) +{ + struct i596_cmd *ptr; + + while (lp->cmd_head != NULL) { + ptr = lp->cmd_head; + lp->cmd_head = ptr->v_next; + lp->cmd_backlog--; + + switch (SWAP16(ptr->command) & 0x7) { + case CmdTx: + { + struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; + struct sk_buff *skb = tx_cmd->skb; + dma_unmap_single(dev->dev.parent, + tx_cmd->dma_addr, + skb->len, DMA_TO_DEVICE); + + dev_kfree_skb(skb); + + dev->stats.tx_errors++; + dev->stats.tx_aborted_errors++; + + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + tx_cmd->cmd.command = 0; /* Mark as free */ + break; + } + default: + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + } + DMA_WBACK_INV(dev, ptr, sizeof(struct i596_cmd)); + } + + wait_cmd(dev, lp->dma, 100, "i596_cleanup_cmd timed out"); + lp->dma->scb.cmd = I596_NULL; + DMA_WBACK(dev, &(lp->dma->scb), sizeof(struct i596_scb)); +} + + +static inline void i596_reset(struct net_device *dev, struct i596_private *lp) +{ + unsigned long flags; + + DEB(DEB_RESET, printk(KERN_DEBUG "i596_reset\n")); + + spin_lock_irqsave (&lp->lock, flags); + + wait_cmd(dev, lp->dma, 100, "i596_reset timed out"); + + netif_stop_queue(dev); + + /* FIXME: this command might cause an lpmc */ + lp->dma->scb.command = SWAP16(CUC_ABORT | RX_ABORT); + DMA_WBACK(dev, &(lp->dma->scb), sizeof(struct i596_scb)); + ca(dev); + + /* wait for shutdown */ + wait_cmd(dev, lp->dma, 1000, "i596_reset 2 timed out"); + spin_unlock_irqrestore (&lp->lock, flags); + + i596_cleanup_cmd(dev, lp); + i596_rx(dev); + + netif_start_queue(dev); + init_i596_mem(dev); +} + + +static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + unsigned long flags; + + DEB(DEB_ADDCMD, printk(KERN_DEBUG "i596_add_cmd cmd_head %p\n", + lp->cmd_head)); + + cmd->status = 0; + cmd->command |= SWAP16(CMD_EOL | CMD_INTR); + cmd->v_next = NULL; + cmd->b_next = I596_NULL; + DMA_WBACK(dev, cmd, sizeof(struct i596_cmd)); + + spin_lock_irqsave (&lp->lock, flags); + + if (lp->cmd_head != NULL) { + lp->cmd_tail->v_next = cmd; + lp->cmd_tail->b_next = SWAP32(virt_to_dma(lp, &cmd->status)); + DMA_WBACK(dev, lp->cmd_tail, sizeof(struct i596_cmd)); + } else { + lp->cmd_head = cmd; + wait_cmd(dev, dma, 100, "i596_add_cmd timed out"); + dma->scb.cmd = SWAP32(virt_to_dma(lp, &cmd->status)); + dma->scb.command = SWAP16(CUC_START); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + ca(dev); + } + lp->cmd_tail = cmd; + lp->cmd_backlog++; + + spin_unlock_irqrestore (&lp->lock, flags); + + if (lp->cmd_backlog > max_cmd_backlog) { + unsigned long tickssofar = jiffies - lp->last_cmd; + + if (tickssofar < ticks_limit) + return; + + printk(KERN_ERR + "%s: command unit timed out, status resetting.\n", + dev->name); +#if 1 + i596_reset(dev, lp); +#endif + } +} + +static int i596_open(struct net_device *dev) +{ + DEB(DEB_OPEN, printk(KERN_DEBUG + "%s: i596_open() irq %d.\n", dev->name, dev->irq)); + + if (init_rx_bufs(dev)) { + printk(KERN_ERR "%s: Failed to init rx bufs\n", dev->name); + return -EAGAIN; + } + if (init_i596_mem(dev)) { + printk(KERN_ERR "%s: Failed to init memory\n", dev->name); + goto out_remove_rx_bufs; + } + netif_start_queue(dev); + + return 0; + +out_remove_rx_bufs: + remove_rx_bufs(dev); + return -EAGAIN; +} + +static void i596_tx_timeout (struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + + /* Transmitter timeout, serious problems. */ + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: transmit timed out, status resetting.\n", + dev->name)); + + dev->stats.tx_errors++; + + /* Try to restart the adaptor */ + if (lp->last_restart == dev->stats.tx_packets) { + DEB(DEB_ERRORS, printk(KERN_DEBUG "Resetting board.\n")); + /* Shutdown and restart */ + i596_reset (dev, lp); + } else { + /* Issue a channel attention signal */ + DEB(DEB_ERRORS, printk(KERN_DEBUG "Kicking board.\n")); + lp->dma->scb.command = SWAP16(CUC_START | RX_START); + DMA_WBACK_INV(dev, &(lp->dma->scb), sizeof(struct i596_scb)); + ca (dev); + lp->last_restart = dev->stats.tx_packets; + } + + dev->trans_start = jiffies; /* prevent tx timeout */ + netif_wake_queue (dev); +} + + +static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct tx_cmd *tx_cmd; + struct i596_tbd *tbd; + short length = skb->len; + + DEB(DEB_STARTTX, printk(KERN_DEBUG + "%s: i596_start_xmit(%x,%p) called\n", + dev->name, skb->len, skb->data)); + + if (length < ETH_ZLEN) { + if (skb_padto(skb, ETH_ZLEN)) + return NETDEV_TX_OK; + length = ETH_ZLEN; + } + + netif_stop_queue(dev); + + tx_cmd = lp->dma->tx_cmds + lp->next_tx_cmd; + tbd = lp->dma->tbds + lp->next_tx_cmd; + + if (tx_cmd->cmd.command) { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: xmit ring full, dropping packet.\n", + dev->name)); + dev->stats.tx_dropped++; + + dev_kfree_skb(skb); + } else { + if (++lp->next_tx_cmd == TX_RING_SIZE) + lp->next_tx_cmd = 0; + tx_cmd->tbd = SWAP32(virt_to_dma(lp, tbd)); + tbd->next = I596_NULL; + + tx_cmd->cmd.command = SWAP16(CMD_FLEX | CmdTx); + tx_cmd->skb = skb; + + tx_cmd->pad = 0; + tx_cmd->size = 0; + tbd->pad = 0; + tbd->size = SWAP16(EOF | length); + + tx_cmd->dma_addr = dma_map_single(dev->dev.parent, skb->data, + skb->len, DMA_TO_DEVICE); + tbd->data = SWAP32(tx_cmd->dma_addr); + + DEB(DEB_TXADDR, print_eth(skb->data, "tx-queued")); + DMA_WBACK_INV(dev, tx_cmd, sizeof(struct tx_cmd)); + DMA_WBACK_INV(dev, tbd, sizeof(struct i596_tbd)); + i596_add_cmd(dev, &tx_cmd->cmd); + + dev->stats.tx_packets++; + dev->stats.tx_bytes += length; + } + + netif_start_queue(dev); + + return NETDEV_TX_OK; +} + +static void print_eth(unsigned char *add, char *str) +{ + printk(KERN_DEBUG "i596 0x%p, %pM --> %pM %02X%02X, %s\n", + add, add + 6, add, add[12], add[13], str); +} +static const struct net_device_ops i596_netdev_ops = { + .ndo_open = i596_open, + .ndo_stop = i596_close, + .ndo_start_xmit = i596_start_xmit, + .ndo_set_multicast_list = set_multicast_list, + .ndo_tx_timeout = i596_tx_timeout, + .ndo_change_mtu = eth_change_mtu, + .ndo_validate_addr = eth_validate_addr, + .ndo_set_mac_address = eth_mac_addr, +#ifdef CONFIG_NET_POLL_CONTROLLER + .ndo_poll_controller = i596_poll_controller, +#endif +}; + +static int __devinit i82596_probe(struct net_device *dev) +{ + int i; + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma; + + /* This lot is ensure things have been cache line aligned. */ + BUILD_BUG_ON(sizeof(struct i596_rfd) != 32); + BUILD_BUG_ON(sizeof(struct i596_rbd) & 31); + BUILD_BUG_ON(sizeof(struct tx_cmd) & 31); + BUILD_BUG_ON(sizeof(struct i596_tbd) != 32); +#ifndef __LP64__ + BUILD_BUG_ON(sizeof(struct i596_dma) > 4096); +#endif + + if (!dev->base_addr || !dev->irq) + return -ENODEV; + + dma = (struct i596_dma *) DMA_ALLOC(dev->dev.parent, + sizeof(struct i596_dma), &lp->dma_addr, GFP_KERNEL); + if (!dma) { + printk(KERN_ERR "%s: Couldn't get shared memory\n", __FILE__); + return -ENOMEM; + } + + dev->netdev_ops = &i596_netdev_ops; + dev->watchdog_timeo = TX_TIMEOUT; + + memset(dma, 0, sizeof(struct i596_dma)); + lp->dma = dma; + + dma->scb.command = 0; + dma->scb.cmd = I596_NULL; + dma->scb.rfd = I596_NULL; + spin_lock_init(&lp->lock); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); + + i = register_netdev(dev); + if (i) { + DMA_FREE(dev->dev.parent, sizeof(struct i596_dma), + (void *)dma, lp->dma_addr); + return i; + } + + DEB(DEB_PROBE, printk(KERN_INFO "%s: 82596 at %#3lx, %pM IRQ %d.\n", + dev->name, dev->base_addr, dev->dev_addr, + dev->irq)); + DEB(DEB_INIT, printk(KERN_INFO + "%s: dma at 0x%p (%d bytes), lp->scb at 0x%p\n", + dev->name, dma, (int)sizeof(struct i596_dma), + &dma->scb)); + + return 0; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void i596_poll_controller(struct net_device *dev) +{ + disable_irq(dev->irq); + i596_interrupt(dev->irq, dev); + enable_irq(dev->irq); +} +#endif + +static irqreturn_t i596_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct i596_private *lp; + struct i596_dma *dma; + unsigned short status, ack_cmd = 0; + + lp = netdev_priv(dev); + dma = lp->dma; + + spin_lock (&lp->lock); + + wait_cmd(dev, dma, 100, "i596 interrupt, timeout"); + status = SWAP16(dma->scb.status); + + DEB(DEB_INTS, printk(KERN_DEBUG + "%s: i596 interrupt, IRQ %d, status %4.4x.\n", + dev->name, dev->irq, status)); + + ack_cmd = status & 0xf000; + + if (!ack_cmd) { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: interrupt with no events\n", + dev->name)); + spin_unlock (&lp->lock); + return IRQ_NONE; + } + + if ((status & 0x8000) || (status & 0x2000)) { + struct i596_cmd *ptr; + + if ((status & 0x8000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt completed command.\n", + dev->name)); + if ((status & 0x2000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt command unit inactive %x.\n", + dev->name, status & 0x0700)); + + while (lp->cmd_head != NULL) { + DMA_INV(dev, lp->cmd_head, sizeof(struct i596_cmd)); + if (!(lp->cmd_head->status & SWAP16(STAT_C))) + break; + + ptr = lp->cmd_head; + + DEB(DEB_STATUS, + printk(KERN_DEBUG + "cmd_head->status = %04x, ->command = %04x\n", + SWAP16(lp->cmd_head->status), + SWAP16(lp->cmd_head->command))); + lp->cmd_head = ptr->v_next; + lp->cmd_backlog--; + + switch (SWAP16(ptr->command) & 0x7) { + case CmdTx: + { + struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; + struct sk_buff *skb = tx_cmd->skb; + + if (ptr->status & SWAP16(STAT_OK)) { + DEB(DEB_TXADDR, + print_eth(skb->data, "tx-done")); + } else { + dev->stats.tx_errors++; + if (ptr->status & SWAP16(0x0020)) + dev->stats.collisions++; + if (!(ptr->status & SWAP16(0x0040))) + dev->stats.tx_heartbeat_errors++; + if (ptr->status & SWAP16(0x0400)) + dev->stats.tx_carrier_errors++; + if (ptr->status & SWAP16(0x0800)) + dev->stats.collisions++; + if (ptr->status & SWAP16(0x1000)) + dev->stats.tx_aborted_errors++; + } + dma_unmap_single(dev->dev.parent, + tx_cmd->dma_addr, + skb->len, DMA_TO_DEVICE); + dev_kfree_skb_irq(skb); + + tx_cmd->cmd.command = 0; /* Mark free */ + break; + } + case CmdTDR: + { + unsigned short status = SWAP16(((struct tdr_cmd *)ptr)->status); + + if (status & 0x8000) { + DEB(DEB_ANY, + printk(KERN_DEBUG "%s: link ok.\n", + dev->name)); + } else { + if (status & 0x4000) + printk(KERN_ERR + "%s: Transceiver problem.\n", + dev->name); + if (status & 0x2000) + printk(KERN_ERR + "%s: Termination problem.\n", + dev->name); + if (status & 0x1000) + printk(KERN_ERR + "%s: Short circuit.\n", + dev->name); + + DEB(DEB_TDR, + printk(KERN_DEBUG "%s: Time %d.\n", + dev->name, status & 0x07ff)); + } + break; + } + case CmdConfigure: + /* + * Zap command so set_multicast_list() know + * it is free + */ + ptr->command = 0; + break; + } + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + DMA_WBACK(dev, ptr, sizeof(struct i596_cmd)); + lp->last_cmd = jiffies; + } + + /* This mess is arranging that only the last of any outstanding + * commands has the interrupt bit set. Should probably really + * only add to the cmd queue when the CU is stopped. + */ + ptr = lp->cmd_head; + while ((ptr != NULL) && (ptr != lp->cmd_tail)) { + struct i596_cmd *prev = ptr; + + ptr->command &= SWAP16(0x1fff); + ptr = ptr->v_next; + DMA_WBACK_INV(dev, prev, sizeof(struct i596_cmd)); + } + + if (lp->cmd_head != NULL) + ack_cmd |= CUC_START; + dma->scb.cmd = SWAP32(virt_to_dma(lp, &lp->cmd_head->status)); + DMA_WBACK_INV(dev, &dma->scb, sizeof(struct i596_scb)); + } + if ((status & 0x1000) || (status & 0x4000)) { + if ((status & 0x4000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt received a frame.\n", + dev->name)); + i596_rx(dev); + /* Only RX_START if stopped - RGH 07-07-96 */ + if (status & 0x1000) { + if (netif_running(dev)) { + DEB(DEB_ERRORS, + printk(KERN_DEBUG + "%s: i596 interrupt receive unit inactive, status 0x%x\n", + dev->name, status)); + ack_cmd |= RX_START; + dev->stats.rx_errors++; + dev->stats.rx_fifo_errors++; + rebuild_rx_bufs(dev); + } + } + } + wait_cmd(dev, dma, 100, "i596 interrupt, timeout"); + dma->scb.command = SWAP16(ack_cmd); + DMA_WBACK(dev, &dma->scb, sizeof(struct i596_scb)); + + /* DANGER: I suspect that some kind of interrupt + acknowledgement aside from acking the 82596 might be needed + here... but it's running acceptably without */ + + ca(dev); + + wait_cmd(dev, dma, 100, "i596 interrupt, exit timeout"); + DEB(DEB_INTS, printk(KERN_DEBUG "%s: exiting interrupt.\n", dev->name)); + + spin_unlock (&lp->lock); + return IRQ_HANDLED; +} + +static int i596_close(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + unsigned long flags; + + netif_stop_queue(dev); + + DEB(DEB_INIT, + printk(KERN_DEBUG + "%s: Shutting down ethercard, status was %4.4x.\n", + dev->name, SWAP16(lp->dma->scb.status))); + + spin_lock_irqsave(&lp->lock, flags); + + wait_cmd(dev, lp->dma, 100, "close1 timed out"); + lp->dma->scb.command = SWAP16(CUC_ABORT | RX_ABORT); + DMA_WBACK(dev, &lp->dma->scb, sizeof(struct i596_scb)); + + ca(dev); + + wait_cmd(dev, lp->dma, 100, "close2 timed out"); + spin_unlock_irqrestore(&lp->lock, flags); + DEB(DEB_STRUCT, i596_display_data(dev)); + i596_cleanup_cmd(dev, lp); + + free_irq(dev->irq, dev); + remove_rx_bufs(dev); + + return 0; +} + +/* + * Set or clear the multicast filter for this adaptor. + */ + +static void set_multicast_list(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int config = 0, cnt; + + DEB(DEB_MULTI, + printk(KERN_DEBUG + "%s: set multicast list, %d entries, promisc %s, allmulti %s\n", + dev->name, netdev_mc_count(dev), + dev->flags & IFF_PROMISC ? "ON" : "OFF", + dev->flags & IFF_ALLMULTI ? "ON" : "OFF")); + + if ((dev->flags & IFF_PROMISC) && + !(dma->cf_cmd.i596_config[8] & 0x01)) { + dma->cf_cmd.i596_config[8] |= 0x01; + config = 1; + } + if (!(dev->flags & IFF_PROMISC) && + (dma->cf_cmd.i596_config[8] & 0x01)) { + dma->cf_cmd.i596_config[8] &= ~0x01; + config = 1; + } + if ((dev->flags & IFF_ALLMULTI) && + (dma->cf_cmd.i596_config[11] & 0x20)) { + dma->cf_cmd.i596_config[11] &= ~0x20; + config = 1; + } + if (!(dev->flags & IFF_ALLMULTI) && + !(dma->cf_cmd.i596_config[11] & 0x20)) { + dma->cf_cmd.i596_config[11] |= 0x20; + config = 1; + } + if (config) { + if (dma->cf_cmd.cmd.command) + printk(KERN_INFO + "%s: config change request already queued\n", + dev->name); + else { + dma->cf_cmd.cmd.command = SWAP16(CmdConfigure); + DMA_WBACK_INV(dev, &dma->cf_cmd, sizeof(struct cf_cmd)); + i596_add_cmd(dev, &dma->cf_cmd.cmd); + } + } + + cnt = netdev_mc_count(dev); + if (cnt > MAX_MC_CNT) { + cnt = MAX_MC_CNT; + printk(KERN_NOTICE "%s: Only %d multicast addresses supported", + dev->name, cnt); + } + + if (!netdev_mc_empty(dev)) { + struct netdev_hw_addr *ha; + unsigned char *cp; + struct mc_cmd *cmd; + + cmd = &dma->mc_cmd; + cmd->cmd.command = SWAP16(CmdMulticastList); + cmd->mc_cnt = SWAP16(netdev_mc_count(dev) * 6); + cp = cmd->mc_addrs; + netdev_for_each_mc_addr(ha, dev) { + if (!cnt--) + break; + memcpy(cp, ha->addr, 6); + if (i596_debug > 1) + DEB(DEB_MULTI, + printk(KERN_DEBUG + "%s: Adding address %pM\n", + dev->name, cp)); + cp += 6; + } + DMA_WBACK_INV(dev, &dma->mc_cmd, sizeof(struct mc_cmd)); + i596_add_cmd(dev, &cmd->cmd); + } +} |