diff options
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_phy.c')
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_phy.c | 95 |
1 files changed, 32 insertions, 63 deletions
diff --git a/drivers/net/ixgbe/ixgbe_phy.c b/drivers/net/ixgbe/ixgbe_phy.c index 2543c32..6d385ea 100644 --- a/drivers/net/ixgbe/ixgbe_phy.c +++ b/drivers/net/ixgbe/ixgbe_phy.c @@ -44,7 +44,6 @@ static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl); static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data); static bool ixgbe_get_i2c_data(u32 *i2cctl); static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw); -static bool ixgbe_validate_phy_addr(struct ixgbe_hw *hw, u32 phy_addr); static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id); static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw); @@ -61,8 +60,7 @@ s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw) if (hw->phy.type == ixgbe_phy_unknown) { for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) { - if (ixgbe_validate_phy_addr(hw, phy_addr)) { - hw->phy.addr = phy_addr; + if (mdio45_probe(&hw->phy.mdio, phy_addr) == 0) { ixgbe_get_phy_id(hw); hw->phy.type = ixgbe_get_phy_type_from_id(hw->phy.id); @@ -78,26 +76,6 @@ s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw) } /** - * ixgbe_validate_phy_addr - Determines phy address is valid - * @hw: pointer to hardware structure - * - **/ -static bool ixgbe_validate_phy_addr(struct ixgbe_hw *hw, u32 phy_addr) -{ - u16 phy_id = 0; - bool valid = false; - - hw->phy.addr = phy_addr; - hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_HIGH, - IXGBE_MDIO_PMA_PMD_DEV_TYPE, &phy_id); - - if (phy_id != 0xFFFF && phy_id != 0x0) - valid = true; - - return valid; -} - -/** * ixgbe_get_phy_id - Get the phy type * @hw: pointer to hardware structure * @@ -108,14 +86,12 @@ static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw) u16 phy_id_high = 0; u16 phy_id_low = 0; - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_HIGH, - IXGBE_MDIO_PMA_PMD_DEV_TYPE, + status = hw->phy.ops.read_reg(hw, MDIO_DEVID1, MDIO_MMD_PMAPMD, &phy_id_high); if (status == 0) { hw->phy.id = (u32)(phy_id_high << 16); - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_LOW, - IXGBE_MDIO_PMA_PMD_DEV_TYPE, + status = hw->phy.ops.read_reg(hw, MDIO_DEVID2, MDIO_MMD_PMAPMD, &phy_id_low); hw->phy.id |= (u32)(phy_id_low & IXGBE_PHY_REVISION_MASK); hw->phy.revision = (u32)(phy_id_low & ~IXGBE_PHY_REVISION_MASK); @@ -160,9 +136,8 @@ s32 ixgbe_reset_phy_generic(struct ixgbe_hw *hw) * Perform soft PHY reset to the PHY_XS. * This will cause a soft reset to the PHY */ - return hw->phy.ops.write_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL, - IXGBE_MDIO_PHY_XS_DEV_TYPE, - IXGBE_MDIO_PHY_XS_RESET); + return hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, + MDIO_CTRL1_RESET); } /** @@ -192,7 +167,7 @@ s32 ixgbe_read_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr, /* Setup and write the address cycle command */ command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | - (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) | + (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) | (IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND)); IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); @@ -223,7 +198,8 @@ s32 ixgbe_read_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr, */ command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | - (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) | + (hw->phy.mdio.prtad << + IXGBE_MSCA_PHY_ADDR_SHIFT) | (IXGBE_MSCA_READ | IXGBE_MSCA_MDI_COMMAND)); IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); @@ -292,7 +268,7 @@ s32 ixgbe_write_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr, /* Setup and write the address cycle command */ command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | - (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) | + (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) | (IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND)); IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); @@ -323,7 +299,8 @@ s32 ixgbe_write_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr, */ command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | - (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) | + (hw->phy.mdio.prtad << + IXGBE_MSCA_PHY_ADDR_SHIFT) | (IXGBE_MSCA_WRITE | IXGBE_MSCA_MDI_COMMAND)); IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); @@ -365,7 +342,7 @@ s32 ixgbe_setup_phy_link_generic(struct ixgbe_hw *hw) s32 status = IXGBE_NOT_IMPLEMENTED; u32 time_out; u32 max_time_out = 10; - u16 autoneg_reg = IXGBE_MII_AUTONEG_REG; + u16 autoneg_reg; /* * Set advertisement settings in PHY based on autoneg_advertised @@ -373,36 +350,31 @@ s32 ixgbe_setup_phy_link_generic(struct ixgbe_hw *hw) * tnx devices cannot be "forced" to a autoneg 10G and fail. But can * for a 1G. */ - hw->phy.ops.read_reg(hw, IXGBE_MII_SPEED_SELECTION_REG, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg); + hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, &autoneg_reg); if (hw->phy.autoneg_advertised == IXGBE_LINK_SPEED_1GB_FULL) - autoneg_reg &= 0xEFFF; /* 0 in bit 12 is 1G operation */ + autoneg_reg &= ~MDIO_AN_10GBT_CTRL_ADV10G; else - autoneg_reg |= 0x1000; /* 1 in bit 12 is 10G/1G operation */ + autoneg_reg |= MDIO_AN_10GBT_CTRL_ADV10G; - hw->phy.ops.write_reg(hw, IXGBE_MII_SPEED_SELECTION_REG, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg); + hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, autoneg_reg); /* Restart PHY autonegotiation and wait for completion */ - hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg); + hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_AN, &autoneg_reg); - autoneg_reg |= IXGBE_MII_RESTART; + autoneg_reg |= MDIO_AN_CTRL1_RESTART; - hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg); + hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_AN, autoneg_reg); /* Wait for autonegotiation to finish */ for (time_out = 0; time_out < max_time_out; time_out++) { udelay(10); /* Restart PHY autonegotiation and wait for completion */ - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, + status = hw->phy.ops.read_reg(hw, MDIO_STAT1, MDIO_MMD_AN, &autoneg_reg); - autoneg_reg &= IXGBE_MII_AUTONEG_COMPLETE; - if (autoneg_reg == IXGBE_MII_AUTONEG_COMPLETE) { + autoneg_reg &= MDIO_AN_STAT1_COMPLETE; + if (autoneg_reg == MDIO_AN_STAT1_COMPLETE) { status = 0; break; } @@ -457,23 +429,21 @@ s32 ixgbe_reset_phy_nl(struct ixgbe_hw *hw) s32 ret_val = 0; u32 i; - hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL, - IXGBE_MDIO_PHY_XS_DEV_TYPE, &phy_data); + hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, &phy_data); /* reset the PHY and poll for completion */ - hw->phy.ops.write_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL, - IXGBE_MDIO_PHY_XS_DEV_TYPE, - (phy_data | IXGBE_MDIO_PHY_XS_RESET)); + hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, + (phy_data | MDIO_CTRL1_RESET)); for (i = 0; i < 100; i++) { - hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL, - IXGBE_MDIO_PHY_XS_DEV_TYPE, &phy_data); - if ((phy_data & IXGBE_MDIO_PHY_XS_RESET) == 0) + hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, + &phy_data); + if ((phy_data & MDIO_CTRL1_RESET) == 0) break; msleep(10); } - if ((phy_data & IXGBE_MDIO_PHY_XS_RESET) != 0) { + if ((phy_data & MDIO_CTRL1_RESET) != 0) { hw_dbg(hw, "PHY reset did not complete.\n"); ret_val = IXGBE_ERR_PHY; goto out; @@ -509,7 +479,7 @@ s32 ixgbe_reset_phy_nl(struct ixgbe_hw *hw) for (i = 0; i < edata; i++) { hw->eeprom.ops.read(hw, data_offset, &eword); hw->phy.ops.write_reg(hw, phy_offset, - IXGBE_TWINAX_DEV, eword); + MDIO_MMD_PMAPMD, eword); hw_dbg(hw, "Wrote %4.4x to %4.4x\n", eword, phy_offset); data_offset++; @@ -1302,7 +1272,7 @@ s32 ixgbe_check_phy_link_tnx(struct ixgbe_hw *hw, ixgbe_link_speed *speed, udelay(10); status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_VENDOR_SPECIFIC_1_STATUS, - IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, + MDIO_MMD_VEND1, &phy_data); phy_link = phy_data & IXGBE_MDIO_VENDOR_SPECIFIC_1_LINK_STATUS; @@ -1330,8 +1300,7 @@ s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw, { s32 status = 0; - status = hw->phy.ops.read_reg(hw, TNX_FW_REV, - IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, + status = hw->phy.ops.read_reg(hw, TNX_FW_REV, MDIO_MMD_VEND1, firmware_version); return status; |