diff options
Diffstat (limited to 'drivers/net/wireless')
104 files changed, 7596 insertions, 28910 deletions
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig index 85f8bf4..56dd665 100644 --- a/drivers/net/wireless/Kconfig +++ b/drivers/net/wireless/Kconfig @@ -16,118 +16,9 @@ menuconfig WLAN if WLAN -menuconfig WLAN_PRE80211 - bool "Wireless LAN (pre-802.11)" - depends on NETDEVICES - ---help--- - Say Y if you have any pre-802.11 wireless LAN hardware. - - This option does not affect the kernel build, it only - lets you choose drivers. - -config STRIP - tristate "STRIP (Metricom starmode radio IP)" - depends on INET && WLAN_PRE80211 - select WIRELESS_EXT - ---help--- - Say Y if you have a Metricom radio and intend to use Starmode Radio - IP. STRIP is a radio protocol developed for the MosquitoNet project - to send Internet traffic using Metricom radios. Metricom radios are - small, battery powered, 100kbit/sec packet radio transceivers, about - the size and weight of a cellular telephone. (You may also have heard - them called "Metricom modems" but we avoid the term "modem" because - it misleads many people into thinking that you can plug a Metricom - modem into a phone line and use it as a modem.) - - You can use STRIP on any Linux machine with a serial port, although - it is obviously most useful for people with laptop computers. If you - think you might get a Metricom radio in the future, there is no harm - in saying Y to STRIP now, except that it makes the kernel a bit - bigger. - - To compile this as a module, choose M here: the module will be - called strip. - -config ARLAN - tristate "Aironet Arlan 655 & IC2200 DS support" - depends on ISA && !64BIT && WLAN_PRE80211 - select WIRELESS_EXT - ---help--- - Aironet makes Arlan, a class of wireless LAN adapters. These use the - www.Telxon.com chip, which is also used on several similar cards. - This driver is tested on the 655 and IC2200 series cards. Look at - <http://www.ylenurme.ee/~elmer/655/> for the latest information. - - The driver is built as two modules, arlan and arlan-proc. The latter - is the /proc interface and is not needed most of time. - - On some computers the card ends up in non-valid state after some - time. Use a ping-reset script to clear it. - -config WAVELAN - tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support" - depends on ISA && WLAN_PRE80211 - select WIRELESS_EXT - select WEXT_SPY - select WEXT_PRIV - ---help--- - The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is - a Radio LAN (wireless Ethernet-like Local Area Network) using the - radio frequencies 900 MHz and 2.4 GHz. - - If you want to use an ISA WaveLAN card under Linux, say Y and read - the Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. Some more specific - information is contained in - <file:Documentation/networking/wavelan.txt> and in the source code - <file:drivers/net/wireless/wavelan.p.h>. - - You will also need the wireless tools package available from - <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>. - Please read the man pages contained therein. - - To compile this driver as a module, choose M here: the module will be - called wavelan. - -config PCMCIA_WAVELAN - tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support" - depends on PCMCIA && WLAN_PRE80211 - select WIRELESS_EXT - select WEXT_SPY - select WEXT_PRIV - help - Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA - (PC-card) wireless Ethernet networking card to your computer. This - driver is for the non-IEEE-802.11 Wavelan cards. - - To compile this driver as a module, choose M here: the module will be - called wavelan_cs. If unsure, say N. - -config PCMCIA_NETWAVE - tristate "Xircom Netwave AirSurfer Pcmcia wireless support" - depends on PCMCIA && WLAN_PRE80211 - select WIRELESS_EXT - select WEXT_PRIV - help - Say Y here if you intend to attach this type of PCMCIA (PC-card) - wireless Ethernet networking card to your computer. - - To compile this driver as a module, choose M here: the module will be - called netwave_cs. If unsure, say N. - - -menuconfig WLAN_80211 - bool "Wireless LAN (IEEE 802.11)" - depends on NETDEVICES - ---help--- - Say Y if you have any 802.11 wireless LAN hardware. - - This option does not affect the kernel build, it only - lets you choose drivers. - config PCMCIA_RAYCS tristate "Aviator/Raytheon 2.4GHz wireless support" - depends on PCMCIA && WLAN_80211 + depends on PCMCIA select WIRELESS_EXT select WEXT_SPY select WEXT_PRIV @@ -142,7 +33,7 @@ config PCMCIA_RAYCS config LIBERTAS_THINFIRM tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware" - depends on WLAN_80211 && MAC80211 + depends on MAC80211 select FW_LOADER ---help--- A library for Marvell Libertas 8xxx devices using thinfirm. @@ -155,7 +46,7 @@ config LIBERTAS_THINFIRM_USB config AIRO tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards" - depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN) + depends on ISA_DMA_API && (PCI || BROKEN) select WIRELESS_EXT select CRYPTO select WEXT_SPY @@ -175,7 +66,7 @@ config AIRO config ATMEL tristate "Atmel at76c50x chipset 802.11b support" - depends on (PCI || PCMCIA) && WLAN_80211 + depends on (PCI || PCMCIA) select WIRELESS_EXT select WEXT_PRIV select FW_LOADER @@ -210,7 +101,7 @@ config PCMCIA_ATMEL config AT76C50X_USB tristate "Atmel at76c503/at76c505/at76c505a USB cards" - depends on MAC80211 && WLAN_80211 && USB + depends on MAC80211 && USB select FW_LOADER ---help--- Enable support for USB Wireless devices using Atmel at76c503, @@ -218,8 +109,9 @@ config AT76C50X_USB config AIRO_CS tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards" - depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211 + depends on PCMCIA && (BROKEN || !M32R) select WIRELESS_EXT + select WEXT_SPY select CRYPTO select CRYPTO_AES ---help--- @@ -238,7 +130,7 @@ config AIRO_CS config PCMCIA_WL3501 tristate "Planet WL3501 PCMCIA cards" - depends on EXPERIMENTAL && PCMCIA && WLAN_80211 + depends on EXPERIMENTAL && PCMCIA select WIRELESS_EXT select WEXT_SPY help @@ -248,7 +140,7 @@ config PCMCIA_WL3501 config PRISM54 tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus (DEPRECATED)' - depends on PCI && EXPERIMENTAL && WLAN_80211 + depends on PCI && EXPERIMENTAL select WIRELESS_EXT select WEXT_SPY select WEXT_PRIV @@ -272,7 +164,7 @@ config PRISM54 config USB_ZD1201 tristate "USB ZD1201 based Wireless device support" - depends on USB && WLAN_80211 + depends on USB select WIRELESS_EXT select WEXT_PRIV select FW_LOADER @@ -291,7 +183,7 @@ config USB_ZD1201 config USB_NET_RNDIS_WLAN tristate "Wireless RNDIS USB support" - depends on USB && WLAN_80211 && EXPERIMENTAL + depends on USB && EXPERIMENTAL depends on CFG80211 select USB_USBNET select USB_NET_CDCETHER @@ -319,7 +211,7 @@ config USB_NET_RNDIS_WLAN config RTL8180 tristate "Realtek 8180/8185 PCI support" - depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL + depends on MAC80211 && PCI && EXPERIMENTAL select EEPROM_93CX6 ---help--- This is a driver for RTL8180 and RTL8185 based cards. @@ -375,7 +267,7 @@ config RTL8180 config RTL8187 tristate "Realtek 8187 and 8187B USB support" - depends on MAC80211 && USB && WLAN_80211 + depends on MAC80211 && USB select EEPROM_93CX6 ---help--- This is a driver for RTL8187 and RTL8187B based cards. @@ -404,7 +296,7 @@ config RTL8187_LEDS config ADM8211 tristate "ADMtek ADM8211 support" - depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL + depends on MAC80211 && PCI && EXPERIMENTAL select CRC32 select EEPROM_93CX6 ---help--- @@ -431,7 +323,7 @@ config ADM8211 config MAC80211_HWSIM tristate "Simulated radio testing tool for mac80211" - depends on MAC80211 && WLAN_80211 + depends on MAC80211 ---help--- This driver is a developer testing tool that can be used to test IEEE 802.11 networking stack (mac80211) functionality. This is not @@ -444,7 +336,7 @@ config MAC80211_HWSIM config MWL8K tristate "Marvell 88W8xxx PCI/PCIe Wireless support" - depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL + depends on MAC80211 && PCI && EXPERIMENTAL ---help--- This driver supports Marvell TOPDOG 802.11 wireless cards. diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile index 7a4647e..5d4ce4d 100644 --- a/drivers/net/wireless/Makefile +++ b/drivers/net/wireless/Makefile @@ -5,16 +5,6 @@ obj-$(CONFIG_IPW2100) += ipw2x00/ obj-$(CONFIG_IPW2200) += ipw2x00/ -obj-$(CONFIG_STRIP) += strip.o -obj-$(CONFIG_ARLAN) += arlan.o - -arlan-objs := arlan-main.o arlan-proc.o - -# Obsolete cards -obj-$(CONFIG_WAVELAN) += wavelan.o -obj-$(CONFIG_PCMCIA_NETWAVE) += netwave_cs.o -obj-$(CONFIG_PCMCIA_WAVELAN) += wavelan_cs.o - obj-$(CONFIG_HERMES) += orinoco/ obj-$(CONFIG_AIRO) += airo.o diff --git a/drivers/net/wireless/arlan-main.c b/drivers/net/wireless/arlan-main.c deleted file mode 100644 index 921a082..0000000 --- a/drivers/net/wireless/arlan-main.c +++ /dev/null @@ -1,1887 +0,0 @@ -/* - * Copyright (C) 1997 Cullen Jennings - * Copyright (C) 1998 Elmer Joandiu, elmer@ylenurme.ee - * GNU General Public License applies - * This module provides support for the Arlan 655 card made by Aironet - */ - -#include "arlan.h" - -#if BITS_PER_LONG != 32 -# error FIXME: this driver requires a 32-bit platform -#endif - -static const char *arlan_version = "C.Jennigs 97 & Elmer.Joandi@ut.ee Oct'98, http://www.ylenurme.ee/~elmer/655/"; - -struct net_device *arlan_device[MAX_ARLANS]; - -static int SID = SIDUNKNOWN; -static int radioNodeId = radioNodeIdUNKNOWN; -static char encryptionKey[12] = {'a', 'b', 'c', 'd', 'e', 'f', 'g', 'h'}; -int arlan_debug = debugUNKNOWN; -static int spreadingCode = spreadingCodeUNKNOWN; -static int channelNumber = channelNumberUNKNOWN; -static int channelSet = channelSetUNKNOWN; -static int systemId = systemIdUNKNOWN; -static int registrationMode = registrationModeUNKNOWN; -static int keyStart; -static int tx_delay_ms; -static int retries = 5; -static int tx_queue_len = 1; -static int arlan_EEPROM_bad; - -#ifdef ARLAN_DEBUGGING - -static int testMemory = testMemoryUNKNOWN; -static int irq = irqUNKNOWN; -static int txScrambled = 1; -static int mdebug; - -module_param(irq, int, 0); -module_param(mdebug, int, 0); -module_param(testMemory, int, 0); -module_param(txScrambled, int, 0); -MODULE_PARM_DESC(irq, "(unused)"); -MODULE_PARM_DESC(testMemory, "(unused)"); -MODULE_PARM_DESC(mdebug, "Arlan multicast debugging (0-1)"); -#endif - -module_param_named(debug, arlan_debug, int, 0); -module_param(spreadingCode, int, 0); -module_param(channelNumber, int, 0); -module_param(channelSet, int, 0); -module_param(systemId, int, 0); -module_param(registrationMode, int, 0); -module_param(radioNodeId, int, 0); -module_param(SID, int, 0); -module_param(keyStart, int, 0); -module_param(tx_delay_ms, int, 0); -module_param(retries, int, 0); -module_param(tx_queue_len, int, 0); -module_param_named(EEPROM_bad, arlan_EEPROM_bad, int, 0); -MODULE_PARM_DESC(debug, "Arlan debug enable (0-1)"); -MODULE_PARM_DESC(retries, "Arlan maximum packet retransmisions"); -#ifdef ARLAN_ENTRY_EXIT_DEBUGGING -static int arlan_entry_debug; -static int arlan_exit_debug; -static int arlan_entry_and_exit_debug; -module_param_named(entry_debug, arlan_entry_debug, int, 0); -module_param_named(exit_debug, arlan_exit_debug, int, 0); -module_param_named(entry_and_exit_debug, arlan_entry_and_exit_debug, int, 0); -MODULE_PARM_DESC(entry_debug, "Arlan driver function entry debugging"); -MODULE_PARM_DESC(exit_debug, "Arlan driver function exit debugging"); -MODULE_PARM_DESC(entry_and_exit_debug, "Arlan driver function entry and exit debugging"); -#endif - -struct arlan_conf_stru arlan_conf[MAX_ARLANS]; -static int arlans_found; - -static int arlan_open(struct net_device *dev); -static netdev_tx_t arlan_tx(struct sk_buff *skb, struct net_device *dev); -static irqreturn_t arlan_interrupt(int irq, void *dev_id); -static int arlan_close(struct net_device *dev); -static struct net_device_stats * - arlan_statistics (struct net_device *dev); -static void arlan_set_multicast (struct net_device *dev); -static int arlan_hw_tx (struct net_device* dev, char *buf, int length ); -static int arlan_hw_config (struct net_device * dev); -static void arlan_tx_done_interrupt (struct net_device * dev, int status); -static void arlan_rx_interrupt (struct net_device * dev, u_char rxStatus, u_short, u_short); -static void arlan_process_interrupt (struct net_device * dev); -static void arlan_tx_timeout (struct net_device *dev); - -static inline long us2ticks(int us) -{ - return us * (1000000 / HZ); -} - - -#ifdef ARLAN_ENTRY_EXIT_DEBUGGING -#define ARLAN_DEBUG_ENTRY(name) \ - {\ - struct timeval timev;\ - do_gettimeofday(&timev);\ - if (arlan_entry_debug || arlan_entry_and_exit_debug)\ - printk("--->>>" name " %ld " "\n",((long int) timev.tv_sec * 1000000 + timev.tv_usec));\ - } -#define ARLAN_DEBUG_EXIT(name) \ - {\ - struct timeval timev;\ - do_gettimeofday(&timev);\ - if (arlan_exit_debug || arlan_entry_and_exit_debug)\ - printk("<<<---" name " %ld " "\n",((long int) timev.tv_sec * 1000000 + timev.tv_usec) );\ - } -#else -#define ARLAN_DEBUG_ENTRY(name) -#define ARLAN_DEBUG_EXIT(name) -#endif - - -#define arlan_interrupt_ack(dev)\ - clearClearInterrupt(dev);\ - setClearInterrupt(dev); - -static inline int arlan_drop_tx(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - dev->stats.tx_errors++; - if (priv->Conf->tx_delay_ms) - { - priv->tx_done_delayed = jiffies + priv->Conf->tx_delay_ms * HZ / 1000 + 1; - } - else - { - priv->waiting_command_mask &= ~ARLAN_COMMAND_TX; - TXHEAD(dev).offset = 0; - TXTAIL(dev).offset = 0; - priv->txLast = 0; - priv->bad = 0; - if (!priv->under_reset && !priv->under_config) - netif_wake_queue (dev); - } - return 1; -} - - -int arlan_command(struct net_device *dev, int command_p) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - struct arlan_conf_stru *conf = priv->Conf; - int udelayed = 0; - int i = 0; - unsigned long flags; - - ARLAN_DEBUG_ENTRY("arlan_command"); - - if (priv->card_polling_interval) - priv->card_polling_interval = 1; - - if (arlan_debug & ARLAN_DEBUG_CHAIN_LOCKS) - printk(KERN_DEBUG "arlan_command, %lx commandByte %x waiting %lx incoming %x \n", - jiffies, READSHMB(arlan->commandByte), - priv->waiting_command_mask, command_p); - - priv->waiting_command_mask |= command_p; - - if (priv->waiting_command_mask & ARLAN_COMMAND_RESET) - if (time_after(jiffies, priv->lastReset + 5 * HZ)) - priv->waiting_command_mask &= ~ARLAN_COMMAND_RESET; - - if (priv->waiting_command_mask & ARLAN_COMMAND_INT_ACK) - { - arlan_interrupt_ack(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_INT_ACK; - } - if (priv->waiting_command_mask & ARLAN_COMMAND_INT_ENABLE) - { - setInterruptEnable(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_INT_ENABLE; - } - - /* Card access serializing lock */ - spin_lock_irqsave(&priv->lock, flags); - - /* Check cards status and waiting */ - - if (priv->waiting_command_mask & (ARLAN_COMMAND_LONG_WAIT_NOW | ARLAN_COMMAND_WAIT_NOW)) - { - while (priv->waiting_command_mask & (ARLAN_COMMAND_LONG_WAIT_NOW | ARLAN_COMMAND_WAIT_NOW)) - { - if (READSHMB(arlan->resetFlag) || - READSHMB(arlan->commandByte)) /* || - (readControlRegister(dev) & ARLAN_ACCESS)) - */ - udelay(40); - else - priv->waiting_command_mask &= ~(ARLAN_COMMAND_LONG_WAIT_NOW | ARLAN_COMMAND_WAIT_NOW); - - udelayed++; - - if (priv->waiting_command_mask & ARLAN_COMMAND_LONG_WAIT_NOW) - { - if (udelayed * 40 > 1000000) - { - printk(KERN_ERR "%s long wait too long \n", dev->name); - priv->waiting_command_mask |= ARLAN_COMMAND_RESET; - break; - } - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_WAIT_NOW) - { - if (udelayed * 40 > 1000) - { - printk(KERN_ERR "%s short wait too long \n", dev->name); - goto bad_end; - } - } - } - } - else - { - i = 0; - while ((READSHMB(arlan->resetFlag) || - READSHMB(arlan->commandByte)) && - conf->pre_Command_Wait > (i++) * 10) - udelay(10); - - - if ((READSHMB(arlan->resetFlag) || - READSHMB(arlan->commandByte)) && - !(priv->waiting_command_mask & ARLAN_COMMAND_RESET)) - { - goto card_busy_end; - } - } - if (priv->waiting_command_mask & ARLAN_COMMAND_RESET) - priv->under_reset = 1; - if (priv->waiting_command_mask & ARLAN_COMMAND_CONF) - priv->under_config = 1; - - /* Issuing command */ - arlan_lock_card_access(dev); - if (priv->waiting_command_mask & ARLAN_COMMAND_POWERUP) - { - // if (readControlRegister(dev) & (ARLAN_ACCESS && ARLAN_POWER)) - setPowerOn(dev); - arlan_interrupt_lancpu(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_POWERUP; - priv->waiting_command_mask |= ARLAN_COMMAND_RESET; - priv->card_polling_interval = HZ / 10; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_ACTIVATE) - { - WRITESHMB(arlan->commandByte, ARLAN_COM_ACTIVATE); - arlan_interrupt_lancpu(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_ACTIVATE; - priv->card_polling_interval = HZ / 10; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_RX_ABORT) - { - if (priv->rx_command_given) - { - WRITESHMB(arlan->commandByte, ARLAN_COM_RX_ABORT); - arlan_interrupt_lancpu(dev); - priv->rx_command_given = 0; - } - priv->waiting_command_mask &= ~ARLAN_COMMAND_RX_ABORT; - priv->card_polling_interval = 1; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_TX_ABORT) - { - if (priv->tx_command_given) - { - WRITESHMB(arlan->commandByte, ARLAN_COM_TX_ABORT); - arlan_interrupt_lancpu(dev); - priv->tx_command_given = 0; - } - priv->waiting_command_mask &= ~ARLAN_COMMAND_TX_ABORT; - priv->card_polling_interval = 1; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_RESET) - { - priv->under_reset=1; - netif_stop_queue (dev); - - arlan_drop_tx(dev); - if (priv->tx_command_given || priv->rx_command_given) - { - printk(KERN_ERR "%s: Reset under tx or rx command \n", dev->name); - } - netif_stop_queue (dev); - if (arlan_debug & ARLAN_DEBUG_RESET) - printk(KERN_ERR "%s: Doing chip reset\n", dev->name); - priv->lastReset = jiffies; - WRITESHM(arlan->commandByte, 0, u_char); - /* hold card in reset state */ - setHardwareReset(dev); - /* set reset flag and then release reset */ - WRITESHM(arlan->resetFlag, 0xff, u_char); - clearChannelAttention(dev); - clearHardwareReset(dev); - priv->card_polling_interval = HZ / 4; - priv->waiting_command_mask &= ~ARLAN_COMMAND_RESET; - priv->waiting_command_mask |= ARLAN_COMMAND_INT_RACK; -// priv->waiting_command_mask |= ARLAN_COMMAND_INT_RENABLE; -// priv->waiting_command_mask |= ARLAN_COMMAND_RX; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_INT_RACK) - { - clearHardwareReset(dev); - clearClearInterrupt(dev); - setClearInterrupt(dev); - setInterruptEnable(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_INT_RACK; - priv->waiting_command_mask |= ARLAN_COMMAND_CONF; - priv->under_config = 1; - priv->under_reset = 0; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_INT_RENABLE) - { - setInterruptEnable(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_INT_RENABLE; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_CONF) - { - if (priv->tx_command_given || priv->rx_command_given) - { - printk(KERN_ERR "%s: Reset under tx or rx command \n", dev->name); - } - arlan_drop_tx(dev); - setInterruptEnable(dev); - arlan_hw_config(dev); - arlan_interrupt_lancpu(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_CONF; - priv->card_polling_interval = HZ / 10; -// priv->waiting_command_mask |= ARLAN_COMMAND_INT_RACK; -// priv->waiting_command_mask |= ARLAN_COMMAND_INT_ENABLE; - priv->waiting_command_mask |= ARLAN_COMMAND_CONF_WAIT; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_CONF_WAIT) - { - if (READSHMB(arlan->configuredStatusFlag) != 0 && - READSHMB(arlan->diagnosticInfo) == 0xff) - { - priv->waiting_command_mask &= ~ARLAN_COMMAND_CONF_WAIT; - priv->waiting_command_mask |= ARLAN_COMMAND_RX; - priv->waiting_command_mask |= ARLAN_COMMAND_TBUSY_CLEAR; - priv->card_polling_interval = HZ / 10; - priv->tx_command_given = 0; - priv->under_config = 0; - } - else - { - priv->card_polling_interval = 1; - if (arlan_debug & ARLAN_DEBUG_TIMING) - printk(KERN_ERR "configure delayed \n"); - } - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_RX) - { - if (!registrationBad(dev)) - { - setInterruptEnable(dev); - memset_io(arlan->commandParameter, 0, 0xf); - WRITESHMB(arlan->commandByte, ARLAN_COM_INT | ARLAN_COM_RX_ENABLE); - WRITESHMB(arlan->commandParameter[0], conf->rxParameter); - arlan_interrupt_lancpu(dev); - priv->rx_command_given = 0; // mnjah, bad - priv->waiting_command_mask &= ~ARLAN_COMMAND_RX; - priv->card_polling_interval = 1; - } - else - priv->card_polling_interval = 2; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_TBUSY_CLEAR) - { - if ( !registrationBad(dev) && - (netif_queue_stopped(dev) || !netif_running(dev)) ) - { - priv->waiting_command_mask &= ~ARLAN_COMMAND_TBUSY_CLEAR; - netif_wake_queue (dev); - } - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_TX) - { - if (!test_and_set_bit(0, (void *) &priv->tx_command_given)) - { - if (time_after(jiffies, - priv->tx_last_sent + us2ticks(conf->rx_tweak1)) - || time_before(jiffies, - priv->last_rx_int_ack_time + us2ticks(conf->rx_tweak2))) - { - setInterruptEnable(dev); - memset_io(arlan->commandParameter, 0, 0xf); - WRITESHMB(arlan->commandByte, ARLAN_COM_TX_ENABLE | ARLAN_COM_INT); - memcpy_toio(arlan->commandParameter, &TXLAST(dev), 14); -// for ( i=1 ; i < 15 ; i++) printk("%02x:",READSHMB(arlan->commandParameter[i])); - priv->tx_last_sent = jiffies; - arlan_interrupt_lancpu(dev); - priv->tx_command_given = 1; - priv->waiting_command_mask &= ~ARLAN_COMMAND_TX; - priv->card_polling_interval = 1; - } - else - { - priv->tx_command_given = 0; - priv->card_polling_interval = 1; - } - } - else if (arlan_debug & ARLAN_DEBUG_CHAIN_LOCKS) - printk(KERN_ERR "tx command when tx chain locked \n"); - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_NOOPINT) - { - { - WRITESHMB(arlan->commandByte, ARLAN_COM_NOP | ARLAN_COM_INT); - } - arlan_interrupt_lancpu(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_NOOPINT; - priv->card_polling_interval = HZ / 3; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_NOOP) - { - WRITESHMB(arlan->commandByte, ARLAN_COM_NOP); - arlan_interrupt_lancpu(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_NOOP; - priv->card_polling_interval = HZ / 3; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_SLOW_POLL) - { - WRITESHMB(arlan->commandByte, ARLAN_COM_GOTO_SLOW_POLL); - arlan_interrupt_lancpu(dev); - priv->waiting_command_mask &= ~ARLAN_COMMAND_SLOW_POLL; - priv->card_polling_interval = HZ / 3; - } - else if (priv->waiting_command_mask & ARLAN_COMMAND_POWERDOWN) - { - setPowerOff(dev); - if (arlan_debug & ARLAN_DEBUG_CARD_STATE) - printk(KERN_WARNING "%s: Arlan Going Standby\n", dev->name); - priv->waiting_command_mask &= ~ARLAN_COMMAND_POWERDOWN; - priv->card_polling_interval = 3 * HZ; - } - arlan_unlock_card_access(dev); - for (i = 0; READSHMB(arlan->commandByte) && i < 20; i++) - udelay(10); - if (READSHMB(arlan->commandByte)) - if (arlan_debug & ARLAN_DEBUG_CARD_STATE) - printk(KERN_ERR "card busy leaving command %lx\n", priv->waiting_command_mask); - - spin_unlock_irqrestore(&priv->lock, flags); - ARLAN_DEBUG_EXIT("arlan_command"); - priv->last_command_buff_free_time = jiffies; - return 0; - -card_busy_end: - if (time_after(jiffies, priv->last_command_buff_free_time + HZ)) - priv->waiting_command_mask |= ARLAN_COMMAND_CLEAN_AND_RESET; - - if (arlan_debug & ARLAN_DEBUG_CARD_STATE) - printk(KERN_ERR "%s arlan_command card busy end \n", dev->name); - spin_unlock_irqrestore(&priv->lock, flags); - ARLAN_DEBUG_EXIT("arlan_command"); - return 1; - -bad_end: - printk(KERN_ERR "%s arlan_command bad end \n", dev->name); - - spin_unlock_irqrestore(&priv->lock, flags); - ARLAN_DEBUG_EXIT("arlan_command"); - - return -1; -} - -static inline void arlan_command_process(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - int times = 0; - while (priv->waiting_command_mask && times < 8) - { - if (priv->waiting_command_mask) - { - if (arlan_command(dev, 0)) - break; - times++; - } - /* if long command, we won't repeat trying */ ; - if (priv->card_polling_interval > 1) - break; - times++; - } -} - - -static inline void arlan_retransmit_now(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - - ARLAN_DEBUG_ENTRY("arlan_retransmit_now"); - if (TXLAST(dev).offset == 0) - { - if (TXHEAD(dev).offset) - { - priv->txLast = 0; - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) printk(KERN_DEBUG "TX buff switch to head \n"); - - } - else if (TXTAIL(dev).offset) - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) printk(KERN_DEBUG "TX buff switch to tail \n"); - priv->txLast = 1; - } - else - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) printk(KERN_ERR "ReTransmit buff empty"); - netif_wake_queue (dev); - return; - - } - arlan_command(dev, ARLAN_COMMAND_TX); - - priv->Conf->driverRetransmissions++; - priv->retransmissions++; - - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) printk("Retransmit %d bytes \n", TXLAST(dev).length); - - ARLAN_DEBUG_EXIT("arlan_retransmit_now"); -} - - - -static void arlan_registration_timer(unsigned long data) -{ - struct net_device *dev = (struct net_device *) data; - struct arlan_private *priv = netdev_priv(dev); - int bh_mark_needed = 0; - int next_tick = 1; - long lostTime = ((long)jiffies - (long)priv->registrationLastSeen) - * (1000/HZ); - - if (registrationBad(dev)) - { - priv->registrationLostCount++; - if (lostTime > 7000 && lostTime < 7200) - { - printk(KERN_NOTICE "%s registration Lost \n", dev->name); - } - if (lostTime / priv->reRegisterExp > 2000) - arlan_command(dev, ARLAN_COMMAND_CLEAN_AND_CONF); - if (lostTime / (priv->reRegisterExp) > 3500) - arlan_command(dev, ARLAN_COMMAND_CLEAN_AND_RESET); - if (priv->reRegisterExp < 400) - priv->reRegisterExp += 2; - if (lostTime > 7200) - { - next_tick = HZ; - arlan_command(dev, ARLAN_COMMAND_CLEAN_AND_RESET); - } - } - else - { - if (priv->Conf->registrationMode && lostTime > 10000 && - priv->registrationLostCount) - { - printk(KERN_NOTICE "%s registration is back after %ld milliseconds\n", - dev->name, lostTime); - } - priv->registrationLastSeen = jiffies; - priv->registrationLostCount = 0; - priv->reRegisterExp = 1; - if (!netif_running(dev) ) - netif_wake_queue(dev); - if (time_after(priv->tx_last_sent,priv->tx_last_cleared) && - time_after(jiffies, priv->tx_last_sent * 5*HZ) ){ - arlan_command(dev, ARLAN_COMMAND_CLEAN_AND_RESET); - priv->tx_last_cleared = jiffies; - } - } - - - if (!registrationBad(dev) && priv->ReTransmitRequested) - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk(KERN_ERR "Retransmit from timer \n"); - priv->ReTransmitRequested = 0; - arlan_retransmit_now(dev); - } - if (!registrationBad(dev) && - time_after(jiffies, priv->tx_done_delayed) && - priv->tx_done_delayed != 0) - { - TXLAST(dev).offset = 0; - if (priv->txLast) - priv->txLast = 0; - else if (TXTAIL(dev).offset) - priv->txLast = 1; - if (TXLAST(dev).offset) - { - arlan_retransmit_now(dev); - dev->trans_start = jiffies; - } - if (!(TXHEAD(dev).offset && TXTAIL(dev).offset)) - { - netif_wake_queue (dev); - } - priv->tx_done_delayed = 0; - bh_mark_needed = 1; - } - if (bh_mark_needed) - { - netif_wake_queue (dev); - } - arlan_process_interrupt(dev); - - if (next_tick < priv->card_polling_interval) - next_tick = priv->card_polling_interval; - - priv->timer.expires = jiffies + next_tick; - - add_timer(&priv->timer); -} - - -#ifdef ARLAN_DEBUGGING - -static void arlan_print_registers(struct net_device *dev, int line) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem *arlan = priv->card; - - u_char hostcpuLock, lancpuLock, controlRegister, cntrlRegImage, - txStatus, rxStatus, interruptInProgress, commandByte; - - - ARLAN_DEBUG_ENTRY("arlan_print_registers"); - READSHM(interruptInProgress, arlan->interruptInProgress, u_char); - READSHM(hostcpuLock, arlan->hostcpuLock, u_char); - READSHM(lancpuLock, arlan->lancpuLock, u_char); - READSHM(controlRegister, arlan->controlRegister, u_char); - READSHM(cntrlRegImage, arlan->cntrlRegImage, u_char); - READSHM(txStatus, arlan->txStatus, u_char); - READSHM(rxStatus, arlan->rxStatus, u_char); - READSHM(commandByte, arlan->commandByte, u_char); - - printk(KERN_WARNING "line %04d IP %02x HL %02x LL %02x CB %02x CR %02x CRI %02x TX %02x RX %02x\n", - line, interruptInProgress, hostcpuLock, lancpuLock, commandByte, - controlRegister, cntrlRegImage, txStatus, rxStatus); - - ARLAN_DEBUG_EXIT("arlan_print_registers"); -} -#endif - - -static int arlan_hw_tx(struct net_device *dev, char *buf, int length) -{ - int i; - - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - struct arlan_conf_stru *conf = priv->Conf; - - int tailStarts = 0x800; - int headEnds = 0x0; - - - ARLAN_DEBUG_ENTRY("arlan_hw_tx"); - if (TXHEAD(dev).offset) - headEnds = (((TXHEAD(dev).offset + TXHEAD(dev).length - offsetof(struct arlan_shmem, txBuffer)) / 64) + 1) * 64; - if (TXTAIL(dev).offset) - tailStarts = 0x800 - (((TXTAIL(dev).offset - offsetof(struct arlan_shmem, txBuffer)) / 64) + 2) * 64; - - - if (!TXHEAD(dev).offset && length < tailStarts) - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk(KERN_ERR "TXHEAD insert, tailStart %d\n", tailStarts); - - TXHEAD(dev).offset = - offsetof(struct arlan_shmem, txBuffer); - TXHEAD(dev).length = length - ARLAN_FAKE_HDR_LEN; - for (i = 0; i < 6; i++) - TXHEAD(dev).dest[i] = buf[i]; - TXHEAD(dev).clear = conf->txClear; - TXHEAD(dev).retries = conf->txRetries; /* 0 is use default */ - TXHEAD(dev).routing = conf->txRouting; - TXHEAD(dev).scrambled = conf->txScrambled; - memcpy_toio((char __iomem *)arlan + TXHEAD(dev).offset, buf + ARLAN_FAKE_HDR_LEN, TXHEAD(dev).length); - } - else if (!TXTAIL(dev).offset && length < (0x800 - headEnds)) - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk(KERN_ERR "TXTAIL insert, headEnd %d\n", headEnds); - - TXTAIL(dev).offset = - offsetof(struct arlan_shmem, txBuffer) + 0x800 - (length / 64 + 2) * 64; - TXTAIL(dev).length = length - ARLAN_FAKE_HDR_LEN; - for (i = 0; i < 6; i++) - TXTAIL(dev).dest[i] = buf[i]; - TXTAIL(dev).clear = conf->txClear; - TXTAIL(dev).retries = conf->txRetries; - TXTAIL(dev).routing = conf->txRouting; - TXTAIL(dev).scrambled = conf->txScrambled; - memcpy_toio(((char __iomem *)arlan + TXTAIL(dev).offset), buf + ARLAN_FAKE_HDR_LEN, TXTAIL(dev).length); - } - else - { - netif_stop_queue (dev); - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk(KERN_ERR "TX TAIL & HEAD full, return, tailStart %d headEnd %d\n", tailStarts, headEnds); - return -1; - } - priv->out_bytes += length; - priv->out_bytes10 += length; - if (conf->measure_rate < 1) - conf->measure_rate = 1; - if (time_after(jiffies, priv->out_time + conf->measure_rate * HZ)) - { - conf->out_speed = priv->out_bytes / conf->measure_rate; - priv->out_bytes = 0; - priv->out_time = jiffies; - } - if (time_after(jiffies, priv->out_time10 + conf->measure_rate * 10*HZ)) - { - conf->out_speed10 = priv->out_bytes10 / (10 * conf->measure_rate); - priv->out_bytes10 = 0; - priv->out_time10 = jiffies; - } - if (TXHEAD(dev).offset && TXTAIL(dev).offset) - { - netif_stop_queue (dev); - return 0; - } - else - netif_start_queue (dev); - - - IFDEBUG(ARLAN_DEBUG_HEADER_DUMP) - printk(KERN_WARNING "%s Transmit t %2x:%2x:%2x:%2x:%2x:%2x f %2x:%2x:%2x:%2x:%2x:%2x \n", dev->name, - (unsigned char) buf[0], (unsigned char) buf[1], (unsigned char) buf[2], (unsigned char) buf[3], - (unsigned char) buf[4], (unsigned char) buf[5], (unsigned char) buf[6], (unsigned char) buf[7], - (unsigned char) buf[8], (unsigned char) buf[9], (unsigned char) buf[10], (unsigned char) buf[11]); - - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) printk(KERN_ERR "TX command prepare for buffer %d\n", priv->txLast); - - arlan_command(dev, ARLAN_COMMAND_TX); - - priv->tx_last_sent = jiffies; - - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) printk("%s TX Qued %d bytes \n", dev->name, length); - - ARLAN_DEBUG_EXIT("arlan_hw_tx"); - - return 0; -} - - -static int arlan_hw_config(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - struct arlan_conf_stru *conf = priv->Conf; - - ARLAN_DEBUG_ENTRY("arlan_hw_config"); - - printk(KERN_NOTICE "%s arlan configure called \n", dev->name); - if (arlan_EEPROM_bad) - printk(KERN_NOTICE "arlan configure with eeprom bad option \n"); - - - WRITESHM(arlan->spreadingCode, conf->spreadingCode, u_char); - WRITESHM(arlan->channelSet, conf->channelSet, u_char); - - if (arlan_EEPROM_bad) - WRITESHM(arlan->defaultChannelSet, conf->channelSet, u_char); - - WRITESHM(arlan->channelNumber, conf->channelNumber, u_char); - - WRITESHM(arlan->scramblingDisable, conf->scramblingDisable, u_char); - WRITESHM(arlan->txAttenuation, conf->txAttenuation, u_char); - - WRITESHM(arlan->systemId, conf->systemId, u_int); - - WRITESHM(arlan->maxRetries, conf->maxRetries, u_char); - WRITESHM(arlan->receiveMode, conf->receiveMode, u_char); - WRITESHM(arlan->priority, conf->priority, u_char); - WRITESHM(arlan->rootOrRepeater, conf->rootOrRepeater, u_char); - WRITESHM(arlan->SID, conf->SID, u_int); - - WRITESHM(arlan->registrationMode, conf->registrationMode, u_char); - - WRITESHM(arlan->registrationFill, conf->registrationFill, u_char); - WRITESHM(arlan->localTalkAddress, conf->localTalkAddress, u_char); - WRITESHM(arlan->codeFormat, conf->codeFormat, u_char); - WRITESHM(arlan->numChannels, conf->numChannels, u_char); - WRITESHM(arlan->channel1, conf->channel1, u_char); - WRITESHM(arlan->channel2, conf->channel2, u_char); - WRITESHM(arlan->channel3, conf->channel3, u_char); - WRITESHM(arlan->channel4, conf->channel4, u_char); - WRITESHM(arlan->radioNodeId, conf->radioNodeId, u_short); - WRITESHM(arlan->SID, conf->SID, u_int); - WRITESHM(arlan->waitTime, conf->waitTime, u_short); - WRITESHM(arlan->lParameter, conf->lParameter, u_short); - memcpy_toio(&(arlan->_15), &(conf->_15), 3); - WRITESHM(arlan->_15, conf->_15, u_short); - WRITESHM(arlan->headerSize, conf->headerSize, u_short); - if (arlan_EEPROM_bad) - WRITESHM(arlan->hardwareType, conf->hardwareType, u_char); - WRITESHM(arlan->radioType, conf->radioType, u_char); - if (arlan_EEPROM_bad) - WRITESHM(arlan->radioModule, conf->radioType, u_char); - - memcpy_toio(arlan->encryptionKey + keyStart, encryptionKey, 8); - memcpy_toio(arlan->name, conf->siteName, 16); - - WRITESHMB(arlan->commandByte, ARLAN_COM_INT | ARLAN_COM_CONF); /* do configure */ - memset_io(arlan->commandParameter, 0, 0xf); /* 0xf */ - memset_io(arlan->commandParameter + 1, 0, 2); - if (conf->writeEEPROM) - { - memset_io(arlan->commandParameter, conf->writeEEPROM, 1); -// conf->writeEEPROM=0; - } - if (conf->registrationMode && conf->registrationInterrupts) - memset_io(arlan->commandParameter + 3, 1, 1); - else - memset_io(arlan->commandParameter + 3, 0, 1); - - priv->irq_test_done = 0; - - if (conf->tx_queue_len) - dev->tx_queue_len = conf->tx_queue_len; - udelay(100); - - ARLAN_DEBUG_EXIT("arlan_hw_config"); - return 0; -} - - -static int arlan_read_card_configuration(struct net_device *dev) -{ - u_char tlx415; - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - struct arlan_conf_stru *conf = priv->Conf; - - ARLAN_DEBUG_ENTRY("arlan_read_card_configuration"); - - if (radioNodeId == radioNodeIdUNKNOWN) - { - READSHM(conf->radioNodeId, arlan->radioNodeId, u_short); - } - else - conf->radioNodeId = radioNodeId; - - if (SID == SIDUNKNOWN) - { - READSHM(conf->SID, arlan->SID, u_int); - } - else conf->SID = SID; - - if (spreadingCode == spreadingCodeUNKNOWN) - { - READSHM(conf->spreadingCode, arlan->spreadingCode, u_char); - } - else - conf->spreadingCode = spreadingCode; - - if (channelSet == channelSetUNKNOWN) - { - READSHM(conf->channelSet, arlan->channelSet, u_char); - } - else conf->channelSet = channelSet; - - if (channelNumber == channelNumberUNKNOWN) - { - READSHM(conf->channelNumber, arlan->channelNumber, u_char); - } - else conf->channelNumber = channelNumber; - - READSHM(conf->scramblingDisable, arlan->scramblingDisable, u_char); - READSHM(conf->txAttenuation, arlan->txAttenuation, u_char); - - if (systemId == systemIdUNKNOWN) - { - READSHM(conf->systemId, arlan->systemId, u_int); - } - else conf->systemId = systemId; - - READSHM(conf->maxDatagramSize, arlan->maxDatagramSize, u_short); - READSHM(conf->maxFrameSize, arlan->maxFrameSize, u_short); - READSHM(conf->maxRetries, arlan->maxRetries, u_char); - READSHM(conf->receiveMode, arlan->receiveMode, u_char); - READSHM(conf->priority, arlan->priority, u_char); - READSHM(conf->rootOrRepeater, arlan->rootOrRepeater, u_char); - - if (SID == SIDUNKNOWN) - { - READSHM(conf->SID, arlan->SID, u_int); - } - else conf->SID = SID; - - if (registrationMode == registrationModeUNKNOWN) - { - READSHM(conf->registrationMode, arlan->registrationMode, u_char); - } - else conf->registrationMode = registrationMode; - - READSHM(conf->registrationFill, arlan->registrationFill, u_char); - READSHM(conf->localTalkAddress, arlan->localTalkAddress, u_char); - READSHM(conf->codeFormat, arlan->codeFormat, u_char); - READSHM(conf->numChannels, arlan->numChannels, u_char); - READSHM(conf->channel1, arlan->channel1, u_char); - READSHM(conf->channel2, arlan->channel2, u_char); - READSHM(conf->channel3, arlan->channel3, u_char); - READSHM(conf->channel4, arlan->channel4, u_char); - READSHM(conf->waitTime, arlan->waitTime, u_short); - READSHM(conf->lParameter, arlan->lParameter, u_short); - READSHM(conf->_15, arlan->_15, u_short); - READSHM(conf->headerSize, arlan->headerSize, u_short); - READSHM(conf->hardwareType, arlan->hardwareType, u_char); - READSHM(conf->radioType, arlan->radioModule, u_char); - - if (conf->radioType == 0) - conf->radioType = 0xc; - - WRITESHM(arlan->configStatus, 0xA5, u_char); - READSHM(tlx415, arlan->configStatus, u_char); - - if (tlx415 != 0xA5) - printk(KERN_INFO "%s tlx415 chip \n", dev->name); - - conf->txClear = 0; - conf->txRetries = 1; - conf->txRouting = 1; - conf->txScrambled = 0; - conf->rxParameter = 1; - conf->txTimeoutMs = 4000; - conf->waitCardTimeout = 100000; - conf->receiveMode = ARLAN_RCV_CLEAN; - memcpy_fromio(conf->siteName, arlan->name, 16); - conf->siteName[16] = '\0'; - conf->retries = retries; - conf->tx_delay_ms = tx_delay_ms; - conf->ReTransmitPacketMaxSize = 200; - conf->waitReTransmitPacketMaxSize = 200; - conf->txAckTimeoutMs = 900; - conf->fastReTransCount = 3; - - ARLAN_DEBUG_EXIT("arlan_read_card_configuration"); - - return 0; -} - - -static int lastFoundAt = 0xbe000; - - -/* - * This is the real probe routine. Linux has a history of friendly device - * probes on the ISA bus. A good device probes avoids doing writes, and - * verifies that the correct device exists and functions. - */ -#define ARLAN_SHMEM_SIZE 0x2000 -static int __init arlan_check_fingerprint(unsigned long memaddr) -{ - static const char probeText[] = "TELESYSTEM SLW INC. ARLAN \0"; - volatile struct arlan_shmem __iomem *arlan = (struct arlan_shmem *) memaddr; - unsigned long paddr = virt_to_phys((void *) memaddr); - char tempBuf[49]; - - ARLAN_DEBUG_ENTRY("arlan_check_fingerprint"); - - if (!request_mem_region(paddr, ARLAN_SHMEM_SIZE, "arlan")) { - // printk(KERN_WARNING "arlan: memory region %lx excluded from probing \n",paddr); - return -ENODEV; - } - - memcpy_fromio(tempBuf, arlan->textRegion, 29); - tempBuf[30] = 0; - - /* check for card at this address */ - if (0 != strncmp(tempBuf, probeText, 29)){ - release_mem_region(paddr, ARLAN_SHMEM_SIZE); - return -ENODEV; - } - -// printk(KERN_INFO "arlan found at 0x%x \n",memaddr); - ARLAN_DEBUG_EXIT("arlan_check_fingerprint"); - - return 0; -} - -static int arlan_change_mtu(struct net_device *dev, int new_mtu) -{ - struct arlan_private *priv = netdev_priv(dev); - struct arlan_conf_stru *conf = priv->Conf; - - ARLAN_DEBUG_ENTRY("arlan_change_mtu"); - if (new_mtu > 2032) - return -EINVAL; - dev->mtu = new_mtu; - if (new_mtu < 256) - new_mtu = 256; /* cards book suggests 1600 */ - conf->maxDatagramSize = new_mtu; - conf->maxFrameSize = new_mtu + 48; - - arlan_command(dev, ARLAN_COMMAND_CLEAN_AND_CONF); - printk(KERN_NOTICE "%s mtu changed to %d \n", dev->name, new_mtu); - - ARLAN_DEBUG_EXIT("arlan_change_mtu"); - - return 0; -} - -static int arlan_mac_addr(struct net_device *dev, void *p) -{ - struct sockaddr *addr = p; - - - ARLAN_DEBUG_ENTRY("arlan_mac_addr"); - return -EINVAL; - - if (netif_running(dev)) - return -EBUSY; - memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); - - ARLAN_DEBUG_EXIT("arlan_mac_addr"); - return 0; -} - -static const struct net_device_ops arlan_netdev_ops = { - .ndo_open = arlan_open, - .ndo_stop = arlan_close, - .ndo_start_xmit = arlan_tx, - .ndo_get_stats = arlan_statistics, - .ndo_set_multicast_list = arlan_set_multicast, - .ndo_change_mtu = arlan_change_mtu, - .ndo_set_mac_address = arlan_mac_addr, - .ndo_tx_timeout = arlan_tx_timeout, - .ndo_validate_addr = eth_validate_addr, -}; - -static int __init arlan_setup_device(struct net_device *dev, int num) -{ - struct arlan_private *ap = netdev_priv(dev); - int err; - - ARLAN_DEBUG_ENTRY("arlan_setup_device"); - - ap->conf = (struct arlan_shmem *)(ap+1); - - dev->tx_queue_len = tx_queue_len; - dev->netdev_ops = &arlan_netdev_ops; - dev->watchdog_timeo = 3*HZ; - - ap->irq_test_done = 0; - ap->Conf = &arlan_conf[num]; - - ap->Conf->pre_Command_Wait = 40; - ap->Conf->rx_tweak1 = 30; - ap->Conf->rx_tweak2 = 0; - - - err = register_netdev(dev); - if (err) { - release_mem_region(virt_to_phys((void *) dev->mem_start), - ARLAN_SHMEM_SIZE); - free_netdev(dev); - return err; - } - arlan_device[num] = dev; - ARLAN_DEBUG_EXIT("arlan_setup_device"); - return 0; -} - -static int __init arlan_probe_here(struct net_device *dev, - unsigned long memaddr) -{ - struct arlan_private *ap = netdev_priv(dev); - - ARLAN_DEBUG_ENTRY("arlan_probe_here"); - - if (arlan_check_fingerprint(memaddr)) - return -ENODEV; - - printk(KERN_NOTICE "%s: Arlan found at %llx, \n ", dev->name, - (u64) virt_to_phys((void*)memaddr)); - - ap->card = (void *) memaddr; - dev->mem_start = memaddr; - dev->mem_end = memaddr + ARLAN_SHMEM_SIZE-1; - - if (dev->irq < 2) - { - READSHM(dev->irq, ap->card->irqLevel, u_char); - } else if (dev->irq == 2) - dev->irq = 9; - - arlan_read_card_configuration(dev); - - ARLAN_DEBUG_EXIT("arlan_probe_here"); - return 0; -} - - -static int arlan_open(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - int ret = 0; - - ARLAN_DEBUG_ENTRY("arlan_open"); - - ret = request_irq(dev->irq, &arlan_interrupt, 0, dev->name, dev); - if (ret) - { - printk(KERN_ERR "%s: unable to get IRQ %d .\n", - dev->name, dev->irq); - return ret; - } - - - priv->bad = 0; - priv->lastReset = 0; - priv->reset = 0; - memcpy_fromio(dev->dev_addr, arlan->lanCardNodeId, 6); - memset(dev->broadcast, 0xff, 6); - dev->tx_queue_len = tx_queue_len; - priv->interrupt_processing_active = 0; - spin_lock_init(&priv->lock); - - netif_start_queue (dev); - - priv->registrationLostCount = 0; - priv->registrationLastSeen = jiffies; - priv->txLast = 0; - priv->tx_command_given = 0; - priv->rx_command_given = 0; - - priv->reRegisterExp = 1; - priv->tx_last_sent = jiffies - 1; - priv->tx_last_cleared = jiffies; - priv->Conf->writeEEPROM = 0; - priv->Conf->registrationInterrupts = 1; - - init_timer(&priv->timer); - priv->timer.expires = jiffies + HZ / 10; - priv->timer.data = (unsigned long) dev; - priv->timer.function = &arlan_registration_timer; /* timer handler */ - - arlan_command(dev, ARLAN_COMMAND_POWERUP | ARLAN_COMMAND_LONG_WAIT_NOW); - mdelay(200); - add_timer(&priv->timer); - - ARLAN_DEBUG_EXIT("arlan_open"); - return 0; -} - - -static void arlan_tx_timeout (struct net_device *dev) -{ - printk(KERN_ERR "%s: arlan transmit timed out, kernel decided\n", dev->name); - /* Try to restart the adaptor. */ - arlan_command(dev, ARLAN_COMMAND_CLEAN_AND_RESET); - // dev->trans_start = jiffies; - // netif_start_queue (dev); -} - - -static netdev_tx_t arlan_tx(struct sk_buff *skb, struct net_device *dev) -{ - short length; - unsigned char *buf; - - ARLAN_DEBUG_ENTRY("arlan_tx"); - - length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN; - buf = skb->data; - - if (length + 0x12 > 0x800) { - printk(KERN_ERR "TX RING overflow \n"); - netif_stop_queue (dev); - } - - if (arlan_hw_tx(dev, buf, length) == -1) - goto bad_end; - - dev->trans_start = jiffies; - - dev_kfree_skb(skb); - - arlan_process_interrupt(dev); - ARLAN_DEBUG_EXIT("arlan_tx"); - return NETDEV_TX_OK; - -bad_end: - arlan_process_interrupt(dev); - netif_stop_queue (dev); - ARLAN_DEBUG_EXIT("arlan_tx"); - return NETDEV_TX_BUSY; -} - - -static inline int DoNotReTransmitCrap(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - if (TXLAST(dev).length < priv->Conf->ReTransmitPacketMaxSize) - return 1; - return 0; - -} - -static inline int DoNotWaitReTransmitCrap(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - if (TXLAST(dev).length < priv->Conf->waitReTransmitPacketMaxSize) - return 1; - return 0; -} - -static inline void arlan_queue_retransmit(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - ARLAN_DEBUG_ENTRY("arlan_queue_retransmit"); - - if (DoNotWaitReTransmitCrap(dev)) - { - arlan_drop_tx(dev); - } else - priv->ReTransmitRequested++; - - ARLAN_DEBUG_EXIT("arlan_queue_retransmit"); -} - -static inline void RetryOrFail(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - ARLAN_DEBUG_ENTRY("RetryOrFail"); - - if (priv->retransmissions > priv->Conf->retries || - DoNotReTransmitCrap(dev)) - { - arlan_drop_tx(dev); - } - else if (priv->bad <= priv->Conf->fastReTransCount) - { - arlan_retransmit_now(dev); - } - else arlan_queue_retransmit(dev); - - ARLAN_DEBUG_EXIT("RetryOrFail"); -} - - -static void arlan_tx_done_interrupt(struct net_device *dev, int status) -{ - struct arlan_private *priv = netdev_priv(dev); - - ARLAN_DEBUG_ENTRY("arlan_tx_done_interrupt"); - - priv->tx_last_cleared = jiffies; - priv->tx_command_given = 0; - switch (status) - { - case 1: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit OK\n"); - dev->stats.tx_packets++; - priv->bad = 0; - priv->reset = 0; - priv->retransmissions = 0; - if (priv->Conf->tx_delay_ms) - { - priv->tx_done_delayed = jiffies + (priv->Conf->tx_delay_ms * HZ) / 1000 + 1; - } - else - { - TXLAST(dev).offset = 0; - if (priv->txLast) - priv->txLast = 0; - else if (TXTAIL(dev).offset) - priv->txLast = 1; - if (TXLAST(dev).offset) - { - arlan_retransmit_now(dev); - dev->trans_start = jiffies; - } - if (!TXHEAD(dev).offset || !TXTAIL(dev).offset) - { - netif_wake_queue (dev); - } - } - } - break; - - case 2: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit timed out\n"); - priv->bad += 1; - //arlan_queue_retransmit(dev); - RetryOrFail(dev); - } - break; - - case 3: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit max retries\n"); - priv->bad += 1; - priv->reset = 0; - //arlan_queue_retransmit(dev); - RetryOrFail(dev); - } - break; - - case 4: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit aborted\n"); - priv->bad += 1; - arlan_queue_retransmit(dev); - //RetryOrFail(dev); - } - break; - - case 5: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit not registered\n"); - priv->bad += 1; - //debug=101; - arlan_queue_retransmit(dev); - } - break; - - case 6: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit destination full\n"); - priv->bad += 1; - priv->reset = 0; - //arlan_drop_tx(dev); - arlan_queue_retransmit(dev); - } - break; - - case 7: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit unknown ack\n"); - priv->bad += 1; - priv->reset = 0; - arlan_queue_retransmit(dev); - } - break; - - case 8: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit dest mail box full\n"); - priv->bad += 1; - priv->reset = 0; - //arlan_drop_tx(dev); - arlan_queue_retransmit(dev); - } - break; - - case 9: - { - IFDEBUG(ARLAN_DEBUG_TX_CHAIN) - printk("arlan intr: transmit root dest not reg.\n"); - priv->bad += 1; - priv->reset = 1; - //arlan_drop_tx(dev); - arlan_queue_retransmit(dev); - } - break; - - default: - { - printk(KERN_ERR "arlan intr: transmit status unknown\n"); - priv->bad += 1; - priv->reset = 1; - arlan_drop_tx(dev); - } - } - - ARLAN_DEBUG_EXIT("arlan_tx_done_interrupt"); -} - - -static void arlan_rx_interrupt(struct net_device *dev, u_char rxStatus, u_short rxOffset, u_short pkt_len) -{ - char *skbtmp; - int i = 0; - - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - struct arlan_conf_stru *conf = priv->Conf; - - - ARLAN_DEBUG_ENTRY("arlan_rx_interrupt"); - // by spec, not WRITESHMB(arlan->rxStatus,0x00); - // prohibited here arlan_command(dev, ARLAN_COMMAND_RX); - - if (pkt_len < 10 || pkt_len > 2048) - { - printk(KERN_WARNING "%s: got too short or long packet, len %d \n", dev->name, pkt_len); - return; - } - if (rxOffset + pkt_len > 0x2000) - { - printk("%s: got too long packet, len %d offset %x\n", dev->name, pkt_len, rxOffset); - return; - } - priv->in_bytes += pkt_len; - priv->in_bytes10 += pkt_len; - if (conf->measure_rate < 1) - conf->measure_rate = 1; - if (time_after(jiffies, priv->in_time + conf->measure_rate * HZ)) - { - conf->in_speed = priv->in_bytes / conf->measure_rate; - priv->in_bytes = 0; - priv->in_time = jiffies; - } - if (time_after(jiffies, priv->in_time10 + conf->measure_rate * 10*HZ)) - { - conf->in_speed10 = priv->in_bytes10 / (10 * conf->measure_rate); - priv->in_bytes10 = 0; - priv->in_time10 = jiffies; - } - DEBUGSHM(1, "arlan rcv pkt rxStatus= %d ", arlan->rxStatus, u_char); - switch (rxStatus) - { - case 1: - case 2: - case 3: - { - /* Malloc up new buffer. */ - struct sk_buff *skb; - - DEBUGSHM(50, "arlan recv pkt offs=%d\n", arlan->rxOffset, u_short); - DEBUGSHM(1, "arlan rxFrmType = %d \n", arlan->rxFrmType, u_char); - DEBUGSHM(1, KERN_INFO "arlan rx scrambled = %d \n", arlan->scrambled, u_char); - - /* here we do multicast filtering to avoid slow 8-bit memcopy */ -#ifdef ARLAN_MULTICAST - if (!(dev->flags & IFF_ALLMULTI) && - !(dev->flags & IFF_PROMISC) && - dev->mc_list) - { - char hw_dst_addr[6]; - struct dev_mc_list *dmi = dev->mc_list; - int i; - - memcpy_fromio(hw_dst_addr, arlan->ultimateDestAddress, 6); - if (hw_dst_addr[0] == 0x01) - { - if (mdebug) - if (hw_dst_addr[1] == 0x00) - printk(KERN_ERR "%s mcast 0x0100 \n", dev->name); - else if (hw_dst_addr[1] == 0x40) - printk(KERN_ERR "%s m/bcast 0x0140 \n", dev->name); - while (dmi) - { - if (dmi->dmi_addrlen == 6) { - if (arlan_debug & ARLAN_DEBUG_HEADER_DUMP) - printk(KERN_ERR "%s mcl %pM\n", - dev->name, dmi->dmi_addr); - for (i = 0; i < 6; i++) - if (dmi->dmi_addr[i] != hw_dst_addr[i]) - break; - if (i == 6) - break; - } else - printk(KERN_ERR "%s: invalid multicast address length given.\n", dev->name); - dmi = dmi->next; - } - /* we reach here if multicast filtering is on and packet - * is multicast and not for receive */ - goto end_of_interrupt; - } - } -#endif // ARLAN_MULTICAST - /* multicast filtering ends here */ - pkt_len += ARLAN_FAKE_HDR_LEN; - - skb = dev_alloc_skb(pkt_len + 4); - if (skb == NULL) - { - printk(KERN_ERR "%s: Memory squeeze, dropping packet.\n", dev->name); - dev->stats.rx_dropped++; - break; - } - skb_reserve(skb, 2); - skbtmp = skb_put(skb, pkt_len); - - memcpy_fromio(skbtmp + ARLAN_FAKE_HDR_LEN, ((char __iomem *) arlan) + rxOffset, pkt_len - ARLAN_FAKE_HDR_LEN); - memcpy_fromio(skbtmp, arlan->ultimateDestAddress, 6); - memcpy_fromio(skbtmp + 6, arlan->rxSrc, 6); - WRITESHMB(arlan->rxStatus, 0x00); - arlan_command(dev, ARLAN_COMMAND_RX); - - IFDEBUG(ARLAN_DEBUG_HEADER_DUMP) - { - char immedDestAddress[6]; - char immedSrcAddress[6]; - memcpy_fromio(immedDestAddress, arlan->immedDestAddress, 6); - memcpy_fromio(immedSrcAddress, arlan->immedSrcAddress, 6); - - printk(KERN_WARNING "%s t %pM f %pM imd %pM ims %pM\n", - dev->name, skbtmp, - &skbtmp[6], - immedDestAddress, - immedSrcAddress); - } - skb->protocol = eth_type_trans(skb, dev); - IFDEBUG(ARLAN_DEBUG_HEADER_DUMP) - if (skb->protocol != 0x608 && skb->protocol != 0x8) - { - for (i = 0; i <= 22; i++) - printk("%02x:", (u_char) skbtmp[i + 12]); - printk(KERN_ERR "\n"); - printk(KERN_WARNING "arlan kernel pkt type trans %x \n", skb->protocol); - } - netif_rx(skb); - dev->stats.rx_packets++; - dev->stats.rx_bytes += pkt_len; - } - break; - - default: - printk(KERN_ERR "arlan intr: received unknown status\n"); - dev->stats.rx_crc_errors++; - break; - } - ARLAN_DEBUG_EXIT("arlan_rx_interrupt"); -} - -static void arlan_process_interrupt(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - u_char rxStatus = READSHMB(arlan->rxStatus); - u_char txStatus = READSHMB(arlan->txStatus); - u_short rxOffset = READSHMS(arlan->rxOffset); - u_short pkt_len = READSHMS(arlan->rxLength); - int interrupt_count = 0; - - ARLAN_DEBUG_ENTRY("arlan_process_interrupt"); - - if (test_and_set_bit(0, (void *) &priv->interrupt_processing_active)) - { - if (arlan_debug & ARLAN_DEBUG_CHAIN_LOCKS) - printk(KERN_ERR "interrupt chain reentering \n"); - goto end_int_process; - } - while ((rxStatus || txStatus || priv->interrupt_ack_requested) - && (interrupt_count < 5)) - { - if (rxStatus) - priv->last_rx_int_ack_time = jiffies; - - arlan_command(dev, ARLAN_COMMAND_INT_ACK); - arlan_command(dev, ARLAN_COMMAND_INT_ENABLE); - - IFDEBUG(ARLAN_DEBUG_INTERRUPT) - printk(KERN_ERR "%s: got IRQ rx %x tx %x comm %x rxOff %x rxLen %x \n", - dev->name, rxStatus, txStatus, READSHMB(arlan->commandByte), - rxOffset, pkt_len); - - if (rxStatus == 0 && txStatus == 0) - { - if (priv->irq_test_done) - { - if (!registrationBad(dev)) - IFDEBUG(ARLAN_DEBUG_INTERRUPT) printk(KERN_ERR "%s unknown interrupt(nop? regLost ?) reason tx %d rx %d ", - dev->name, txStatus, rxStatus); - } else { - IFDEBUG(ARLAN_DEBUG_INTERRUPT) - printk(KERN_INFO "%s irq $%d test OK \n", dev->name, dev->irq); - - } - priv->interrupt_ack_requested = 0; - goto ends; - } - if (txStatus != 0) - { - WRITESHMB(arlan->txStatus, 0x00); - arlan_tx_done_interrupt(dev, txStatus); - goto ends; - } - if (rxStatus == 1 || rxStatus == 2) - { /* a packet waiting */ - arlan_rx_interrupt(dev, rxStatus, rxOffset, pkt_len); - goto ends; - } - if (rxStatus > 2 && rxStatus < 0xff) - { - WRITESHMB(arlan->rxStatus, 0x00); - printk(KERN_ERR "%s unknown rxStatus reason tx %d rx %d ", - dev->name, txStatus, rxStatus); - goto ends; - } - if (rxStatus == 0xff) - { - WRITESHMB(arlan->rxStatus, 0x00); - arlan_command(dev, ARLAN_COMMAND_RX); - if (registrationBad(dev)) - netif_device_detach(dev); - if (!registrationBad(dev)) - { - priv->registrationLastSeen = jiffies; - if (!netif_queue_stopped(dev) && !priv->under_reset && !priv->under_config) - netif_wake_queue (dev); - } - goto ends; - } -ends: - - arlan_command_process(dev); - - rxStatus = READSHMB(arlan->rxStatus); - txStatus = READSHMB(arlan->txStatus); - rxOffset = READSHMS(arlan->rxOffset); - pkt_len = READSHMS(arlan->rxLength); - - - priv->irq_test_done = 1; - - interrupt_count++; - } - priv->interrupt_processing_active = 0; - -end_int_process: - arlan_command_process(dev); - - ARLAN_DEBUG_EXIT("arlan_process_interrupt"); - return; -} - -static irqreturn_t arlan_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - u_char rxStatus = READSHMB(arlan->rxStatus); - u_char txStatus = READSHMB(arlan->txStatus); - - ARLAN_DEBUG_ENTRY("arlan_interrupt"); - - - if (!rxStatus && !txStatus) - priv->interrupt_ack_requested++; - - arlan_process_interrupt(dev); - - priv->irq_test_done = 1; - - ARLAN_DEBUG_EXIT("arlan_interrupt"); - return IRQ_HANDLED; - -} - - -static int arlan_close(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - - ARLAN_DEBUG_ENTRY("arlan_close"); - - del_timer_sync(&priv->timer); - - arlan_command(dev, ARLAN_COMMAND_POWERDOWN); - - IFDEBUG(ARLAN_DEBUG_STARTUP) - printk(KERN_NOTICE "%s: Closing device\n", dev->name); - - netif_stop_queue(dev); - free_irq(dev->irq, dev); - - ARLAN_DEBUG_EXIT("arlan_close"); - return 0; -} - -#ifdef ARLAN_DEBUGGING -static long alignLong(volatile u_char * ptr) -{ - long ret; - memcpy_fromio(&ret, (void *) ptr, 4); - return ret; -} -#endif - -/* - * Get the current statistics. - * This may be called with the card open or closed. - */ - -static struct net_device_stats *arlan_statistics(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - - - ARLAN_DEBUG_ENTRY("arlan_statistics"); - - /* Update the statistics from the device registers. */ - - READSHM(dev->stats.collisions, arlan->numReTransmissions, u_int); - READSHM(dev->stats.rx_crc_errors, arlan->numCRCErrors, u_int); - READSHM(dev->stats.rx_dropped, arlan->numFramesDiscarded, u_int); - READSHM(dev->stats.rx_fifo_errors, arlan->numRXBufferOverflows, u_int); - READSHM(dev->stats.rx_frame_errors, arlan->numReceiveFramesLost, u_int); - READSHM(dev->stats.rx_over_errors, arlan->numRXOverruns, u_int); - READSHM(dev->stats.rx_packets, arlan->numDatagramsReceived, u_int); - READSHM(dev->stats.tx_aborted_errors, arlan->numAbortErrors, u_int); - READSHM(dev->stats.tx_carrier_errors, arlan->numStatusTimeouts, u_int); - READSHM(dev->stats.tx_dropped, arlan->numDatagramsDiscarded, u_int); - READSHM(dev->stats.tx_fifo_errors, arlan->numTXUnderruns, u_int); - READSHM(dev->stats.tx_packets, arlan->numDatagramsTransmitted, u_int); - READSHM(dev->stats.tx_window_errors, arlan->numHoldOffs, u_int); - - ARLAN_DEBUG_EXIT("arlan_statistics"); - - return &dev->stats; -} - - -static void arlan_set_multicast(struct net_device *dev) -{ - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - struct arlan_conf_stru *conf = priv->Conf; - int board_conf_needed = 0; - - - ARLAN_DEBUG_ENTRY("arlan_set_multicast"); - - if (dev->flags & IFF_PROMISC) - { - unsigned char recMode; - READSHM(recMode, arlan->receiveMode, u_char); - conf->receiveMode = (ARLAN_RCV_PROMISC | ARLAN_RCV_CONTROL); - if (conf->receiveMode != recMode) - board_conf_needed = 1; - } - else - { - /* turn off promiscuous mode */ - unsigned char recMode; - READSHM(recMode, arlan->receiveMode, u_char); - conf->receiveMode = ARLAN_RCV_CLEAN | ARLAN_RCV_CONTROL; - if (conf->receiveMode != recMode) - board_conf_needed = 1; - } - if (board_conf_needed) - arlan_command(dev, ARLAN_COMMAND_CONF); - - ARLAN_DEBUG_EXIT("arlan_set_multicast"); -} - - -struct net_device * __init arlan_probe(int unit) -{ - struct net_device *dev; - int err; - int m; - - ARLAN_DEBUG_ENTRY("arlan_probe"); - - if (arlans_found == MAX_ARLANS) - return ERR_PTR(-ENODEV); - - /* - * Reserve space for local data and a copy of the shared memory - * that is used by the /proc interface. - */ - dev = alloc_etherdev(sizeof(struct arlan_private) - + sizeof(struct arlan_shmem)); - if (!dev) - return ERR_PTR(-ENOMEM); - - if (unit >= 0) { - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - if (dev->mem_start) { - if (arlan_probe_here(dev, dev->mem_start) == 0) - goto found; - goto not_found; - } - - } - - - for (m = (int)phys_to_virt(lastFoundAt) + ARLAN_SHMEM_SIZE; - m <= (int)phys_to_virt(0xDE000); - m += ARLAN_SHMEM_SIZE) - { - if (arlan_probe_here(dev, m) == 0) - { - lastFoundAt = (int)virt_to_phys((void*)m); - goto found; - } - } - - if (lastFoundAt == 0xbe000) - printk(KERN_ERR "arlan: No Arlan devices found \n"); - - not_found: - free_netdev(dev); - return ERR_PTR(-ENODEV); - - found: - err = arlan_setup_device(dev, arlans_found); - if (err) - dev = ERR_PTR(err); - else if (!arlans_found++) - printk(KERN_INFO "Arlan driver %s\n", arlan_version); - - return dev; -} - -#ifdef MODULE -int __init init_module(void) -{ - int i = 0; - - ARLAN_DEBUG_ENTRY("init_module"); - - if (channelSet != channelSetUNKNOWN || channelNumber != channelNumberUNKNOWN || systemId != systemIdUNKNOWN) - return -EINVAL; - - for (i = 0; i < MAX_ARLANS; i++) { - struct net_device *dev = arlan_probe(i); - - if (IS_ERR(dev)) - return PTR_ERR(dev); - } - init_arlan_proc(); - printk(KERN_INFO "Arlan driver %s\n", arlan_version); - ARLAN_DEBUG_EXIT("init_module"); - return 0; -} - - -void __exit cleanup_module(void) -{ - int i = 0; - struct net_device *dev; - - ARLAN_DEBUG_ENTRY("cleanup_module"); - - IFDEBUG(ARLAN_DEBUG_SHUTDOWN) - printk(KERN_INFO "arlan: unloading module\n"); - - cleanup_arlan_proc(); - - for (i = 0; i < MAX_ARLANS; i++) - { - dev = arlan_device[i]; - if (dev) { - arlan_command(dev, ARLAN_COMMAND_POWERDOWN ); - - unregister_netdev(dev); - release_mem_region(virt_to_phys((void *) dev->mem_start), - ARLAN_SHMEM_SIZE); - free_netdev(dev); - arlan_device[i] = NULL; - } - } - - ARLAN_DEBUG_EXIT("cleanup_module"); -} - - -#endif -MODULE_LICENSE("GPL"); diff --git a/drivers/net/wireless/arlan-proc.c b/drivers/net/wireless/arlan-proc.c deleted file mode 100644 index a8b6896..0000000 --- a/drivers/net/wireless/arlan-proc.c +++ /dev/null @@ -1,1253 +0,0 @@ -#include "arlan.h" - -#include <linux/sysctl.h> - -#ifdef CONFIG_PROC_FS - -/* void enableReceive(struct net_device* dev); -*/ - - - -#define ARLAN_STR_SIZE 0x2ff0 -#define DEV_ARLAN_INFO 1 -#define DEV_ARLAN 1 -#define SARLG(type,var) {\ - pos += sprintf(arlan_drive_info+pos, "%s\t=\t0x%x\n", #var, READSHMB(priva->card->var)); \ - } - -#define SARLBN(type,var,nn) {\ - pos += sprintf(arlan_drive_info+pos, "%s\t=\t0x",#var);\ - for (i=0; i < nn; i++ ) pos += sprintf(arlan_drive_info+pos, "%02x",READSHMB(priva->card->var[i]));\ - pos += sprintf(arlan_drive_info+pos, "\n"); \ - } - -#define SARLBNpln(type,var,nn) {\ - for (i=0; i < nn; i++ ) pos += sprintf(arlan_drive_info+pos, "%02x",READSHMB(priva->card->var[i]));\ - } - -#define SARLSTR(var,nn) {\ - char tmpStr[400];\ - int tmpLn = nn;\ - if (nn > 399 ) tmpLn = 399; \ - memcpy(tmpStr,(char *) priva->conf->var,tmpLn);\ - tmpStr[tmpLn] = 0; \ - pos += sprintf(arlan_drive_info+pos, "%s\t=\t%s \n",#var,priva->conf->var);\ - } - -#define SARLUC(var) SARLG(u_char, var) -#define SARLUCN(var,nn) SARLBN(u_char,var, nn) -#define SARLUS(var) SARLG(u_short, var) -#define SARLUSN(var,nn) SARLBN(u_short,var, nn) -#define SARLUI(var) SARLG(u_int, var) - -#define SARLUSA(var) {\ - u_short tmpVar;\ - memcpy(&tmpVar, (short *) priva->conf->var,2); \ - pos += sprintf(arlan_drive_info+pos, "%s\t=\t0x%x\n",#var, tmpVar);\ -} - -#define SARLUIA(var) {\ - u_int tmpVar;\ - memcpy(&tmpVar, (int* )priva->conf->var,4); \ - pos += sprintf(arlan_drive_info+pos, "%s\t=\t0x%x\n",#var, tmpVar);\ -} - - -static const char *arlan_diagnostic_info_string(struct net_device *dev) -{ - - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - u_char diagnosticInfo; - - READSHM(diagnosticInfo, arlan->diagnosticInfo, u_char); - - switch (diagnosticInfo) - { - case 0xFF: - return "Diagnostic info is OK"; - case 0xFE: - return "ERROR EPROM Checksum error "; - case 0xFD: - return "ERROR Local Ram Test Failed "; - case 0xFC: - return "ERROR SCC failure "; - case 0xFB: - return "ERROR BackBone failure "; - case 0xFA: - return "ERROR transceiver not found "; - case 0xF9: - return "ERROR no more address space "; - case 0xF8: - return "ERROR Checksum error "; - case 0xF7: - return "ERROR Missing SS Code"; - case 0xF6: - return "ERROR Invalid config format"; - case 0xF5: - return "ERROR Reserved errorcode F5"; - case 0xF4: - return "ERROR Invalid spreading code/channel number"; - case 0xF3: - return "ERROR Load Code Error"; - case 0xF2: - return "ERROR Reserver errorcode F2 "; - case 0xF1: - return "ERROR Invalid command receivec by LAN card "; - case 0xF0: - return "ERROR Invalid parameter found in command "; - case 0xEF: - return "ERROR On-chip timer failure "; - case 0xEE: - return "ERROR T410 timer failure "; - case 0xED: - return "ERROR Too Many TxEnable commands "; - case 0xEC: - return "ERROR EEPROM error on radio module "; - default: - return "ERROR unknown Diagnostic info reply code "; - } -} - -static const char *arlan_hardware_type_string(struct net_device *dev) -{ - u_char hardwareType; - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - - READSHM(hardwareType, arlan->hardwareType, u_char); - switch (hardwareType) - { - case 0x00: - return "type A450"; - case 0x01: - return "type A650 "; - case 0x04: - return "type TMA coproc"; - case 0x0D: - return "type A650E "; - case 0x18: - return "type TMA coproc Australian"; - case 0x19: - return "type A650A "; - case 0x26: - return "type TMA coproc European"; - case 0x2E: - return "type A655 "; - case 0x2F: - return "type A655A "; - case 0x30: - return "type A655E "; - case 0x0B: - return "type A670 "; - case 0x0C: - return "type A670E "; - case 0x2D: - return "type A670A "; - case 0x0F: - return "type A411T"; - case 0x16: - return "type A411TA"; - case 0x1B: - return "type A440T"; - case 0x1C: - return "type A412T"; - case 0x1E: - return "type A412TA"; - case 0x22: - return "type A411TE"; - case 0x24: - return "type A412TE"; - case 0x27: - return "type A671T "; - case 0x29: - return "type A671TA "; - case 0x2B: - return "type A671TE "; - case 0x31: - return "type A415T "; - case 0x33: - return "type A415TA "; - case 0x35: - return "type A415TE "; - case 0x37: - return "type A672"; - case 0x39: - return "type A672A "; - case 0x3B: - return "type A672T"; - case 0x6B: - return "type IC2200"; - default: - return "type A672T"; - } -} -#ifdef ARLAN_DEBUGGING -static void arlan_print_diagnostic_info(struct net_device *dev) -{ - int i; - u_char diagnosticInfo; - u_short diagnosticOffset; - u_char hardwareType; - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - - // ARLAN_DEBUG_ENTRY("arlan_print_diagnostic_info"); - - if (READSHMB(arlan->configuredStatusFlag) == 0) - printk("Arlan: Card NOT configured\n"); - else - printk("Arlan: Card is configured\n"); - - READSHM(diagnosticInfo, arlan->diagnosticInfo, u_char); - READSHM(diagnosticOffset, arlan->diagnosticOffset, u_short); - - printk(KERN_INFO "%s\n", arlan_diagnostic_info_string(dev)); - - if (diagnosticInfo != 0xff) - printk("%s arlan: Diagnostic Offset %d \n", dev->name, diagnosticOffset); - - printk("arlan: LAN CODE ID = "); - for (i = 0; i < 6; i++) - DEBUGSHM(1, "%03d:", arlan->lanCardNodeId[i], u_char); - printk("\n"); - - printk("arlan: Arlan BroadCast address = "); - for (i = 0; i < 6; i++) - DEBUGSHM(1, "%03d:", arlan->broadcastAddress[i], u_char); - printk("\n"); - - READSHM(hardwareType, arlan->hardwareType, u_char); - printk(KERN_INFO "%s\n", arlan_hardware_type_string(dev)); - - - DEBUGSHM(1, "arlan: channelNumber=%d\n", arlan->channelNumber, u_char); - DEBUGSHM(1, "arlan: channelSet=%d\n", arlan->channelSet, u_char); - DEBUGSHM(1, "arlan: spreadingCode=%d\n", arlan->spreadingCode, u_char); - DEBUGSHM(1, "arlan: radioNodeId=%d\n", arlan->radioNodeId, u_short); - DEBUGSHM(1, "arlan: SID =%d\n", arlan->SID, u_short); - DEBUGSHM(1, "arlan: rxOffset=%d\n", arlan->rxOffset, u_short); - - DEBUGSHM(1, "arlan: registration mode is %d\n", arlan->registrationMode, u_char); - - printk("arlan: name= "); - IFDEBUG(1) - - for (i = 0; i < 16; i++) - { - char c; - READSHM(c, arlan->name[i], char); - if (c) - printk("%c", c); - } - printk("\n"); - -// ARLAN_DEBUG_EXIT("arlan_print_diagnostic_info"); - -} - - -/****************************** TEST MEMORY **************/ - -static int arlan_hw_test_memory(struct net_device *dev) -{ - u_char *ptr; - int i; - int memlen = sizeof(struct arlan_shmem) - 0xF; /* avoid control register */ - volatile char *arlan_mem = (char *) (dev->mem_start); - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - char pattern; - - ptr = NULL; - - /* hold card in reset state */ - setHardwareReset(dev); - - /* test memory */ - pattern = 0; - for (i = 0; i < memlen; i++) - WRITESHM(arlan_mem[i], ((u_char) pattern++), u_char); - - pattern = 0; - for (i = 0; i < memlen; i++) - { - char res; - READSHM(res, arlan_mem[i], char); - if (res != pattern++) - { - printk(KERN_ERR "Arlan driver memory test 1 failed \n"); - return -1; - } - } - - pattern = 0; - for (i = 0; i < memlen; i++) - WRITESHM(arlan_mem[i], ~(pattern++), char); - - pattern = 0; - for (i = 0; i < memlen; i++) - { - char res; - READSHM(res, arlan_mem[i], char); - if (res != ~(pattern++)) - { - printk(KERN_ERR "Arlan driver memory test 2 failed \n"); - return -1; - } - } - - /* zero memory */ - for (i = 0; i < memlen; i++) - WRITESHM(arlan_mem[i], 0x00, char); - - IFDEBUG(1) printk(KERN_INFO "Arlan: memory tests ok\n"); - - /* set reset flag and then release reset */ - WRITESHM(arlan->resetFlag, 0xff, u_char); - - clearChannelAttention(dev); - clearHardwareReset(dev); - - /* wait for reset flag to become zero, we'll wait for two seconds */ - if (arlan_command(dev, ARLAN_COMMAND_LONG_WAIT_NOW)) - { - printk(KERN_ERR "%s arlan: failed to come back from memory test\n", dev->name); - return -1; - } - return 0; -} - -static int arlan_setup_card_by_book(struct net_device *dev) -{ - u_char irqLevel, configuredStatusFlag; - struct arlan_private *priv = netdev_priv(dev); - volatile struct arlan_shmem __iomem *arlan = priv->card; - -// ARLAN_DEBUG_ENTRY("arlan_setup_card"); - - READSHM(configuredStatusFlag, arlan->configuredStatusFlag, u_char); - - IFDEBUG(10) - if (configuredStatusFlag != 0) - IFDEBUG(10) printk("arlan: CARD IS CONFIGURED\n"); - else - IFDEBUG(10) printk("arlan: card is NOT configured\n"); - - if (testMemory || (READSHMB(arlan->diagnosticInfo) != 0xff)) - if (arlan_hw_test_memory(dev)) - return -1; - - DEBUGSHM(4, "arlan configuredStatus = %d \n", arlan->configuredStatusFlag, u_char); - DEBUGSHM(4, "arlan driver diagnostic: 0x%2x\n", arlan->diagnosticInfo, u_char); - - /* issue nop command - no interrupt */ - arlan_command(dev, ARLAN_COMMAND_NOOP); - if (arlan_command(dev, ARLAN_COMMAND_WAIT_NOW) != 0) - return -1; - - IFDEBUG(50) printk("1st Noop successfully executed !!\n"); - - /* try to turn on the arlan interrupts */ - clearClearInterrupt(dev); - setClearInterrupt(dev); - setInterruptEnable(dev); - - /* issue nop command - with interrupt */ - - arlan_command(dev, ARLAN_COMMAND_NOOPINT); - if (arlan_command(dev, ARLAN_COMMAND_WAIT_NOW) != 0) - return -1; - - - IFDEBUG(50) printk("2nd Noop successfully executed !!\n"); - - READSHM(irqLevel, arlan->irqLevel, u_char) - - if (irqLevel != dev->irq) - { - IFDEBUG(1) printk(KERN_WARNING "arlan dip switches set irq to %d\n", irqLevel); - printk(KERN_WARNING "device driver irq set to %d - does not match\n", dev->irq); - dev->irq = irqLevel; - } - else - IFDEBUG(2) printk("irq level is OK\n"); - - - IFDEBUG(3) arlan_print_diagnostic_info(dev); - - arlan_command(dev, ARLAN_COMMAND_CONF); - - READSHM(configuredStatusFlag, arlan->configuredStatusFlag, u_char); - if (configuredStatusFlag == 0) - { - printk(KERN_WARNING "arlan configure failed\n"); - return -1; - } - arlan_command(dev, ARLAN_COMMAND_LONG_WAIT_NOW); - arlan_command(dev, ARLAN_COMMAND_RX); - arlan_command(dev, ARLAN_COMMAND_LONG_WAIT_NOW); - printk(KERN_NOTICE "%s: arlan driver version %s loaded\n", - dev->name, arlan_version); - -// ARLAN_DEBUG_EXIT("arlan_setup_card"); - - return 0; /* no errors */ -} -#endif - -#ifdef ARLAN_PROC_INTERFACE -#ifdef ARLAN_PROC_SHM_DUMP - -static char arlan_drive_info[ARLAN_STR_SIZE] = "A655\n\0"; - -static int arlan_sysctl_info(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int i; - int retv, pos, devnum; - struct arlan_private *priva = NULL; - struct net_device *dev; - pos = 0; - if (write) - { - printk("wrirte: "); - for (i = 0; i < 100; i++) - printk("adi %x \n", arlan_drive_info[i]); - } - if (ctl->procname == NULL || arlan_drive_info == NULL) - { - printk(KERN_WARNING " procname is NULL in sysctl_table or arlan_drive_info is NULL \n at arlan module\n "); - return -1; - } - devnum = ctl->procname[5] - '0'; - if (devnum < 0 || devnum > MAX_ARLANS - 1) - { - printk(KERN_WARNING "too strange devnum in procfs parse\n "); - return -1; - } - else if (arlan_device[devnum] == NULL) - { - if (ctl->procname) - pos += sprintf(arlan_drive_info + pos, "\t%s\n\n", ctl->procname); - pos += sprintf(arlan_drive_info + pos, "No device found here \n"); - goto final; - } - else - priva = netdev_priv(arlan_device[devnum]); - - if (priva == NULL) - { - printk(KERN_WARNING " Could not find the device private in arlan procsys, bad\n "); - return -1; - } - dev = arlan_device[devnum]; - - memcpy_fromio(priva->conf, priva->card, sizeof(struct arlan_shmem)); - - pos = sprintf(arlan_drive_info, "Arlan info \n"); - /* Header Signature */ - SARLSTR(textRegion, 48); - SARLUC(resetFlag); - pos += sprintf(arlan_drive_info + pos, "diagnosticInfo\t=\t%s \n", arlan_diagnostic_info_string(dev)); - SARLUC(diagnosticInfo); - SARLUS(diagnosticOffset); - SARLUCN(_1, 12); - SARLUCN(lanCardNodeId, 6); - SARLUCN(broadcastAddress, 6); - pos += sprintf(arlan_drive_info + pos, "hardwareType =\t %s \n", arlan_hardware_type_string(dev)); - SARLUC(hardwareType); - SARLUC(majorHardwareVersion); - SARLUC(minorHardwareVersion); - SARLUC(radioModule); - SARLUC(defaultChannelSet); - SARLUCN(_2, 47); - - /* Control/Status Block - 0x0080 */ - SARLUC(interruptInProgress); - SARLUC(cntrlRegImage); - - SARLUCN(_3, 14); - SARLUC(commandByte); - SARLUCN(commandParameter, 15); - - /* Receive Status - 0x00a0 */ - SARLUC(rxStatus); - SARLUC(rxFrmType); - SARLUS(rxOffset); - SARLUS(rxLength); - SARLUCN(rxSrc, 6); - SARLUC(rxBroadcastFlag); - SARLUC(rxQuality); - SARLUC(scrambled); - SARLUCN(_4, 1); - - /* Transmit Status - 0x00b0 */ - SARLUC(txStatus); - SARLUC(txAckQuality); - SARLUC(numRetries); - SARLUCN(_5, 14); - SARLUCN(registeredRouter, 6); - SARLUCN(backboneRouter, 6); - SARLUC(registrationStatus); - SARLUC(configuredStatusFlag); - SARLUCN(_6, 1); - SARLUCN(ultimateDestAddress, 6); - SARLUCN(immedDestAddress, 6); - SARLUCN(immedSrcAddress, 6); - SARLUS(rxSequenceNumber); - SARLUC(assignedLocaltalkAddress); - SARLUCN(_7, 27); - - /* System Parameter Block */ - - /* - Driver Parameters (Novell Specific) */ - - SARLUS(txTimeout); - SARLUS(transportTime); - SARLUCN(_8, 4); - - /* - Configuration Parameters */ - SARLUC(irqLevel); - SARLUC(spreadingCode); - SARLUC(channelSet); - SARLUC(channelNumber); - SARLUS(radioNodeId); - SARLUCN(_9, 2); - SARLUC(scramblingDisable); - SARLUC(radioType); - SARLUS(routerId); - SARLUCN(_10, 9); - SARLUC(txAttenuation); - SARLUIA(systemId); - SARLUS(globalChecksum); - SARLUCN(_11, 4); - SARLUS(maxDatagramSize); - SARLUS(maxFrameSize); - SARLUC(maxRetries); - SARLUC(receiveMode); - SARLUC(priority); - SARLUC(rootOrRepeater); - SARLUCN(specifiedRouter, 6); - SARLUS(fastPollPeriod); - SARLUC(pollDecay); - SARLUSA(fastPollDelay); - SARLUC(arlThreshold); - SARLUC(arlDecay); - SARLUCN(_12, 1); - SARLUS(specRouterTimeout); - SARLUCN(_13, 5); - - /* Scrambled Area */ - SARLUIA(SID); - SARLUCN(encryptionKey, 12); - SARLUIA(_14); - SARLUSA(waitTime); - SARLUSA(lParameter); - SARLUCN(_15, 3); - SARLUS(headerSize); - SARLUS(sectionChecksum); - - SARLUC(registrationMode); - SARLUC(registrationFill); - SARLUS(pollPeriod); - SARLUS(refreshPeriod); - SARLSTR(name, 16); - SARLUCN(NID, 6); - SARLUC(localTalkAddress); - SARLUC(codeFormat); - SARLUC(numChannels); - SARLUC(channel1); - SARLUC(channel2); - SARLUC(channel3); - SARLUC(channel4); - SARLUCN(SSCode, 59); - -/* SARLUCN( _16, 0x140); - */ - /* Statistics Block - 0x0300 */ - SARLUC(hostcpuLock); - SARLUC(lancpuLock); - SARLUCN(resetTime, 18); - SARLUIA(numDatagramsTransmitted); - SARLUIA(numReTransmissions); - SARLUIA(numFramesDiscarded); - SARLUIA(numDatagramsReceived); - SARLUIA(numDuplicateReceivedFrames); - SARLUIA(numDatagramsDiscarded); - SARLUS(maxNumReTransmitDatagram); - SARLUS(maxNumReTransmitFrames); - SARLUS(maxNumConsecutiveDuplicateFrames); - /* misaligned here so we have to go to characters */ - SARLUIA(numBytesTransmitted); - SARLUIA(numBytesReceived); - SARLUIA(numCRCErrors); - SARLUIA(numLengthErrors); - SARLUIA(numAbortErrors); - SARLUIA(numTXUnderruns); - SARLUIA(numRXOverruns); - SARLUIA(numHoldOffs); - SARLUIA(numFramesTransmitted); - SARLUIA(numFramesReceived); - SARLUIA(numReceiveFramesLost); - SARLUIA(numRXBufferOverflows); - SARLUIA(numFramesDiscardedAddrMismatch); - SARLUIA(numFramesDiscardedSIDMismatch); - SARLUIA(numPollsTransmistted); - SARLUIA(numPollAcknowledges); - SARLUIA(numStatusTimeouts); - SARLUIA(numNACKReceived); - SARLUS(auxCmd); - SARLUCN(dumpPtr, 4); - SARLUC(dumpVal); - SARLUC(wireTest); - - /* next 4 seems too long for procfs, over single page ? - SARLUCN( _17, 0x86); - SARLUCN( txBuffer, 0x800); - SARLUCN( rxBuffer, 0x800); - SARLUCN( _18, 0x0bff); - */ - - pos += sprintf(arlan_drive_info + pos, "rxRing\t=\t0x"); - for (i = 0; i < 0x50; i++) - pos += sprintf(arlan_drive_info + pos, "%02x", ((char *) priva->conf)[priva->conf->rxOffset + i]); - pos += sprintf(arlan_drive_info + pos, "\n"); - - SARLUC(configStatus); - SARLUC(_22); - SARLUC(progIOCtrl); - SARLUC(shareMBase); - SARLUC(controlRegister); - - pos += sprintf(arlan_drive_info + pos, " total %d chars\n", pos); - if (ctl) - if (ctl->procname) - pos += sprintf(arlan_drive_info + pos, " driver name : %s\n", ctl->procname); -final: - *lenp = pos; - - if (!write) - retv = proc_dostring(ctl, write, buffer, lenp, ppos); - else - { - *lenp = 0; - return -1; - } - return retv; -} - - -static int arlan_sysctl_info161719(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int i; - int retv, pos, devnum; - struct arlan_private *priva = NULL; - - pos = 0; - devnum = ctl->procname[5] - '0'; - if (arlan_device[devnum] == NULL) - { - pos += sprintf(arlan_drive_info + pos, "No device found here \n"); - goto final; - } - else - priva = netdev_priv(arlan_device[devnum]); - if (priva == NULL) - { - printk(KERN_WARNING " Could not find the device private in arlan procsys, bad\n "); - return -1; - } - memcpy_fromio(priva->conf, priva->card, sizeof(struct arlan_shmem)); - SARLUCN(_16, 0xC0); - SARLUCN(_17, 0x6A); - SARLUCN(_18, 14); - SARLUCN(_19, 0x86); - SARLUCN(_21, 0x3fd); - -final: - *lenp = pos; - retv = proc_dostring(ctl, write, buffer, lenp, ppos); - return retv; -} - -static int arlan_sysctl_infotxRing(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int i; - int retv, pos, devnum; - struct arlan_private *priva = NULL; - - pos = 0; - devnum = ctl->procname[5] - '0'; - if (arlan_device[devnum] == NULL) - { - pos += sprintf(arlan_drive_info + pos, "No device found here \n"); - goto final; - } - else - priva = netdev_priv(arlan_device[devnum]); - if (priva == NULL) - { - printk(KERN_WARNING " Could not find the device private in arlan procsys, bad\n "); - return -1; - } - memcpy_fromio(priva->conf, priva->card, sizeof(struct arlan_shmem)); - SARLBNpln(u_char, txBuffer, 0x800); -final: - *lenp = pos; - retv = proc_dostring(ctl, write, buffer, lenp, ppos); - return retv; -} - -static int arlan_sysctl_inforxRing(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int i; - int retv, pos, devnum; - struct arlan_private *priva = NULL; - - pos = 0; - devnum = ctl->procname[5] - '0'; - if (arlan_device[devnum] == NULL) - { - pos += sprintf(arlan_drive_info + pos, "No device found here \n"); - goto final; - } else - priva = netdev_priv(arlan_device[devnum]); - if (priva == NULL) - { - printk(KERN_WARNING " Could not find the device private in arlan procsys, bad\n "); - return -1; - } - memcpy_fromio(priva->conf, priva->card, sizeof(struct arlan_shmem)); - SARLBNpln(u_char, rxBuffer, 0x800); -final: - *lenp = pos; - retv = proc_dostring(ctl, write, buffer, lenp, ppos); - return retv; -} - -static int arlan_sysctl_info18(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int i; - int retv, pos, devnum; - struct arlan_private *priva = NULL; - - pos = 0; - devnum = ctl->procname[5] - '0'; - if (arlan_device[devnum] == NULL) - { - pos += sprintf(arlan_drive_info + pos, "No device found here \n"); - goto final; - } - else - priva = netdev_priv(arlan_device[devnum]); - if (priva == NULL) - { - printk(KERN_WARNING " Could not find the device private in arlan procsys, bad\n "); - return -1; - } - memcpy_fromio(priva->conf, priva->card, sizeof(struct arlan_shmem)); - SARLBNpln(u_char, _18, 0x800); - -final: - *lenp = pos; - retv = proc_dostring(ctl, write, buffer, lenp, ppos); - return retv; -} - - -#endif /* #ifdef ARLAN_PROC_SHM_DUMP */ - - -static char conf_reset_result[200]; - -static int arlan_configure(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int pos = 0; - int devnum = ctl->procname[6] - '0'; - struct arlan_private *priv; - - if (devnum < 0 || devnum > MAX_ARLANS - 1) - { - printk(KERN_WARNING "too strange devnum in procfs parse\n "); - return -1; - } - else if (arlan_device[devnum] != NULL) - { - priv = netdev_priv(arlan_device[devnum]); - - arlan_command(arlan_device[devnum], ARLAN_COMMAND_CLEAN_AND_CONF); - } - else - return -1; - - *lenp = pos; - return proc_dostring(ctl, write, buffer, lenp, ppos); -} - -static int arlan_sysctl_reset(ctl_table * ctl, int write, - void __user *buffer, size_t * lenp, loff_t *ppos) -{ - int pos = 0; - int devnum = ctl->procname[5] - '0'; - struct arlan_private *priv; - - if (devnum < 0 || devnum > MAX_ARLANS - 1) - { - printk(KERN_WARNING "too strange devnum in procfs parse\n "); - return -1; - } - else if (arlan_device[devnum] != NULL) - { - priv = netdev_priv(arlan_device[devnum]); - arlan_command(arlan_device[devnum], ARLAN_COMMAND_CLEAN_AND_RESET); - - } else - return -1; - *lenp = pos + 3; - return proc_dostring(ctl, write, buffer, lenp, ppos); -} - - -/* Place files in /proc/sys/dev/arlan */ -#define CTBLN(num,card,nam) \ - { .ctl_name = num,\ - .procname = #nam,\ - .data = &(arlan_conf[card].nam),\ - .maxlen = sizeof(int), .mode = 0600, .proc_handler = &proc_dointvec} -#ifdef ARLAN_DEBUGGING - -#define ARLAN_PROC_DEBUG_ENTRIES \ - { .ctl_name = 48, .procname = "entry_exit_debug",\ - .data = &arlan_entry_and_exit_debug,\ - .maxlen = sizeof(int), .mode = 0600, .proc_handler = &proc_dointvec},\ - { .ctl_name = 49, .procname = "debug", .data = &arlan_debug,\ - .maxlen = sizeof(int), .mode = 0600, .proc_handler = &proc_dointvec}, -#else -#define ARLAN_PROC_DEBUG_ENTRIES -#endif - -#define ARLAN_SYSCTL_TABLE_TOTAL(cardNo)\ - CTBLN(1,cardNo,spreadingCode),\ - CTBLN(2,cardNo, channelNumber),\ - CTBLN(3,cardNo, scramblingDisable),\ - CTBLN(4,cardNo, txAttenuation),\ - CTBLN(5,cardNo, systemId), \ - CTBLN(6,cardNo, maxDatagramSize),\ - CTBLN(7,cardNo, maxFrameSize),\ - CTBLN(8,cardNo, maxRetries),\ - CTBLN(9,cardNo, receiveMode),\ - CTBLN(10,cardNo, priority),\ - CTBLN(11,cardNo, rootOrRepeater),\ - CTBLN(12,cardNo, SID),\ - CTBLN(13,cardNo, registrationMode),\ - CTBLN(14,cardNo, registrationFill),\ - CTBLN(15,cardNo, localTalkAddress),\ - CTBLN(16,cardNo, codeFormat),\ - CTBLN(17,cardNo, numChannels),\ - CTBLN(18,cardNo, channel1),\ - CTBLN(19,cardNo, channel2),\ - CTBLN(20,cardNo, channel3),\ - CTBLN(21,cardNo, channel4),\ - CTBLN(22,cardNo, txClear),\ - CTBLN(23,cardNo, txRetries),\ - CTBLN(24,cardNo, txRouting),\ - CTBLN(25,cardNo, txScrambled),\ - CTBLN(26,cardNo, rxParameter),\ - CTBLN(27,cardNo, txTimeoutMs),\ - CTBLN(28,cardNo, waitCardTimeout),\ - CTBLN(29,cardNo, channelSet), \ - {.ctl_name = 30, .procname = "name",\ - .data = arlan_conf[cardNo].siteName,\ - .maxlen = 16, .mode = 0600, .proc_handler = &proc_dostring},\ - CTBLN(31,cardNo,waitTime),\ - CTBLN(32,cardNo,lParameter),\ - CTBLN(33,cardNo,_15),\ - CTBLN(34,cardNo,headerSize),\ - CTBLN(36,cardNo,tx_delay_ms),\ - CTBLN(37,cardNo,retries),\ - CTBLN(38,cardNo,ReTransmitPacketMaxSize),\ - CTBLN(39,cardNo,waitReTransmitPacketMaxSize),\ - CTBLN(40,cardNo,fastReTransCount),\ - CTBLN(41,cardNo,driverRetransmissions),\ - CTBLN(42,cardNo,txAckTimeoutMs),\ - CTBLN(43,cardNo,registrationInterrupts),\ - CTBLN(44,cardNo,hardwareType),\ - CTBLN(45,cardNo,radioType),\ - CTBLN(46,cardNo,writeEEPROM),\ - CTBLN(47,cardNo,writeRadioType),\ - ARLAN_PROC_DEBUG_ENTRIES\ - CTBLN(50,cardNo,in_speed),\ - CTBLN(51,cardNo,out_speed),\ - CTBLN(52,cardNo,in_speed10),\ - CTBLN(53,cardNo,out_speed10),\ - CTBLN(54,cardNo,in_speed_max),\ - CTBLN(55,cardNo,out_speed_max),\ - CTBLN(56,cardNo,measure_rate),\ - CTBLN(57,cardNo,pre_Command_Wait),\ - CTBLN(58,cardNo,rx_tweak1),\ - CTBLN(59,cardNo,rx_tweak2),\ - CTBLN(60,cardNo,tx_queue_len),\ - - - -static ctl_table arlan_conf_table0[] = -{ - ARLAN_SYSCTL_TABLE_TOTAL(0) - -#ifdef ARLAN_PROC_SHM_DUMP - { - .ctl_name = 150, - .procname = "arlan0-txRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_infotxRing, - }, - { - .ctl_name = 151, - .procname = "arlan0-rxRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_inforxRing, - }, - { - .ctl_name = 152, - .procname = "arlan0-18", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info18, - }, - { - .ctl_name = 153, - .procname = "arlan0-ring", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info161719, - }, - { - .ctl_name = 154, - .procname = "arlan0-shm-cpy", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info, - }, -#endif - { - .ctl_name = 155, - .procname = "config0", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_configure - }, - { - .ctl_name = 156, - .procname = "reset0", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_sysctl_reset, - }, - { .ctl_name = 0 } -}; - -static ctl_table arlan_conf_table1[] = -{ - - ARLAN_SYSCTL_TABLE_TOTAL(1) - -#ifdef ARLAN_PROC_SHM_DUMP - { - .ctl_name = 150, - .procname = "arlan1-txRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_infotxRing, - }, - { - .ctl_name = 151, - .procname = "arlan1-rxRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_inforxRing, - }, - { - .ctl_name = 152, - .procname = "arlan1-18", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info18, - }, - { - .ctl_name = 153, - .procname = "arlan1-ring", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info161719, - }, - { - .ctl_name = 154, - .procname = "arlan1-shm-cpy", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info, - }, -#endif - { - .ctl_name = 155, - .procname = "config1", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_configure, - }, - { - .ctl_name = 156, - .procname = "reset1", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_sysctl_reset, - }, - { .ctl_name = 0 } -}; - -static ctl_table arlan_conf_table2[] = -{ - - ARLAN_SYSCTL_TABLE_TOTAL(2) - -#ifdef ARLAN_PROC_SHM_DUMP - { - .ctl_name = 150, - .procname = "arlan2-txRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_infotxRing, - }, - { - .ctl_name = 151, - .procname = "arlan2-rxRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_inforxRing, - }, - { - .ctl_name = 152, - .procname = "arlan2-18", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info18, - }, - { - .ctl_name = 153, - .procname = "arlan2-ring", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info161719, - }, - { - .ctl_name = 154, - .procname = "arlan2-shm-cpy", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info, - }, -#endif - { - .ctl_name = 155, - .procname = "config2", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_configure, - }, - { - .ctl_name = 156, - .procname = "reset2", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_sysctl_reset, - }, - { .ctl_name = 0 } -}; - -static ctl_table arlan_conf_table3[] = -{ - - ARLAN_SYSCTL_TABLE_TOTAL(3) - -#ifdef ARLAN_PROC_SHM_DUMP - { - .ctl_name = 150, - .procname = "arlan3-txRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_infotxRing, - }, - { - .ctl_name = 151, - .procname = "arlan3-rxRing", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_inforxRing, - }, - { - .ctl_name = 152, - .procname = "arlan3-18", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info18, - }, - { - .ctl_name = 153, - .procname = "arlan3-ring", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info161719, - }, - { - .ctl_name = 154, - .procname = "arlan3-shm-cpy", - .data = &arlan_drive_info, - .maxlen = ARLAN_STR_SIZE, - .mode = 0400, - .proc_handler = &arlan_sysctl_info, - }, -#endif - { - .ctl_name = 155, - .procname = "config3", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_configure, - }, - { - .ctl_name = 156, - .procname = "reset3", - .data = &conf_reset_result, - .maxlen = 100, - .mode = 0400, - .proc_handler = &arlan_sysctl_reset, - }, - { .ctl_name = 0 } -}; - - - -static ctl_table arlan_table[] = -{ - { - .ctl_name = 0, - .procname = "arlan0", - .maxlen = 0, - .mode = 0600, - .child = arlan_conf_table0, - }, - { - .ctl_name = 0, - .procname = "arlan1", - .maxlen = 0, - .mode = 0600, - .child = arlan_conf_table1, - }, - { - .ctl_name = 0, - .procname = "arlan2", - .maxlen = 0, - .mode = 0600, - .child = arlan_conf_table2, - }, - { - .ctl_name = 0, - .procname = "arlan3", - .maxlen = 0, - .mode = 0600, - .child = arlan_conf_table3, - }, - { .ctl_name = 0 } -}; - -#else - -static ctl_table arlan_table[MAX_ARLANS + 1] = -{ - { .ctl_name = 0 } -}; -#endif - - -// static int mmtu = 1234; - -static ctl_table arlan_root_table[] = -{ - { - .ctl_name = CTL_ARLAN, - .procname = "arlan", - .maxlen = 0, - .mode = 0555, - .child = arlan_table, - }, - { .ctl_name = 0 } -}; - -/* Make sure that /proc/sys/dev is there */ -//static ctl_table arlan_device_root_table[] = -//{ -// {CTL_DEV, "dev", NULL, 0, 0555, arlan_root_table}, -// {0} -//}; - - -static struct ctl_table_header *arlan_device_sysctl_header; - -int __init init_arlan_proc(void) -{ - - int i = 0; - if (arlan_device_sysctl_header) - return 0; - for (i = 0; i < MAX_ARLANS && arlan_device[i]; i++) - arlan_table[i].ctl_name = i + 1; - arlan_device_sysctl_header = register_sysctl_table(arlan_root_table); - if (!arlan_device_sysctl_header) - return -1; - - return 0; - -} - -void __exit cleanup_arlan_proc(void) -{ - unregister_sysctl_table(arlan_device_sysctl_header); - arlan_device_sysctl_header = NULL; - -} -#endif diff --git a/drivers/net/wireless/arlan.h b/drivers/net/wireless/arlan.h deleted file mode 100644 index fb3ad51..0000000 --- a/drivers/net/wireless/arlan.h +++ /dev/null @@ -1,539 +0,0 @@ -/* - * Copyright (C) 1997 Cullen Jennings - * Copyright (C) 1998 Elmer.Joandi@ut.ee, +37-255-13500 - * GNU General Public License applies - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/skbuff.h> -#include <linux/if_ether.h> /* For the statistics structure. */ -#include <linux/if_arp.h> /* For ARPHRD_ETHER */ -#include <linux/ptrace.h> -#include <linux/ioport.h> -#include <linux/in.h> -#include <linux/slab.h> -#include <linux/string.h> -#include <linux/timer.h> - -#include <linux/init.h> -#include <linux/bitops.h> -#include <asm/system.h> -#include <asm/io.h> -#include <linux/errno.h> -#include <linux/delay.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> - - -//#define ARLAN_DEBUGGING 1 - -#define ARLAN_PROC_INTERFACE -#define MAX_ARLANS 4 /* not more than 4 ! */ -#define ARLAN_PROC_SHM_DUMP /* shows all card registers, makes driver way larger */ - -#define ARLAN_MAX_MULTICAST_ADDRS 16 -#define ARLAN_RCV_CLEAN 0 -#define ARLAN_RCV_PROMISC 1 -#define ARLAN_RCV_CONTROL 2 - -#ifdef CONFIG_PROC_FS -extern int init_arlan_proc(void); -extern void cleanup_arlan_proc(void); -#else -#define init_arlan_proc() ({ 0; }) -#define cleanup_arlan_proc() do { } while (0) -#endif - -extern struct net_device *arlan_device[MAX_ARLANS]; -extern int arlan_debug; -extern int arlan_entry_debug; -extern int arlan_exit_debug; -extern int testMemory; -extern int arlan_command(struct net_device * dev, int command); - -#define SIDUNKNOWN -1 -#define radioNodeIdUNKNOWN -1 -#define irqUNKNOWN 0 -#define debugUNKNOWN 0 -#define testMemoryUNKNOWN 1 -#define spreadingCodeUNKNOWN 0 -#define channelNumberUNKNOWN 0 -#define channelSetUNKNOWN 0 -#define systemIdUNKNOWN -1 -#define registrationModeUNKNOWN -1 - - -#define IFDEBUG( L ) if ( (L) & arlan_debug ) -#define ARLAN_FAKE_HDR_LEN 12 - -#ifdef ARLAN_DEBUGGING - #define DEBUG 1 - #define ARLAN_ENTRY_EXIT_DEBUGGING 1 - #define ARLAN_DEBUG(a,b) printk(KERN_DEBUG a, b) -#else - #define ARLAN_DEBUG(a,b) -#endif - -#define ARLAN_SHMEM_SIZE 0x2000 - -struct arlan_shmem -{ - /* Header Signature */ - volatile char textRegion[48]; - volatile u_char resetFlag; - volatile u_char diagnosticInfo; - volatile u_short diagnosticOffset; - volatile u_char _1[12]; - volatile u_char lanCardNodeId[6]; - volatile u_char broadcastAddress[6]; - volatile u_char hardwareType; - volatile u_char majorHardwareVersion; - volatile u_char minorHardwareVersion; - volatile u_char radioModule;// shows EEPROM, can be overridden at 0x111 - volatile u_char defaultChannelSet; // shows EEProm, can be overriiden at 0x10A - volatile u_char _2[47]; - - /* Control/Status Block - 0x0080 */ - volatile u_char interruptInProgress; /* not used by lancpu */ - volatile u_char cntrlRegImage; /* not used by lancpu */ - volatile u_char _3[13]; - volatile u_char dumpByte; - volatile u_char commandByte; /* non-zero = active */ - volatile u_char commandParameter[15]; - - /* Receive Status - 0x00a0 */ - volatile u_char rxStatus; /* 1- data, 2-control, 0xff - registr change */ - volatile u_char rxFrmType; - volatile u_short rxOffset; - volatile u_short rxLength; - volatile u_char rxSrc[6]; - volatile u_char rxBroadcastFlag; - volatile u_char rxQuality; - volatile u_char scrambled; - volatile u_char _4[1]; - - /* Transmit Status - 0x00b0 */ - volatile u_char txStatus; - volatile u_char txAckQuality; - volatile u_char numRetries; - volatile u_char _5[14]; - volatile u_char registeredRouter[6]; - volatile u_char backboneRouter[6]; - volatile u_char registrationStatus; - volatile u_char configuredStatusFlag; - volatile u_char _6[1]; - volatile u_char ultimateDestAddress[6]; - volatile u_char immedDestAddress[6]; - volatile u_char immedSrcAddress[6]; - volatile u_short rxSequenceNumber; - volatile u_char assignedLocaltalkAddress; - volatile u_char _7[27]; - - /* System Parameter Block */ - - /* - Driver Parameters (Novell Specific) */ - - volatile u_short txTimeout; - volatile u_short transportTime; - volatile u_char _8[4]; - - /* - Configuration Parameters */ - volatile u_char irqLevel; - volatile u_char spreadingCode; - volatile u_char channelSet; - volatile u_char channelNumber; - volatile u_short radioNodeId; - volatile u_char _9[2]; - volatile u_char scramblingDisable; - volatile u_char radioType; - volatile u_short routerId; - volatile u_char _10[9]; - volatile u_char txAttenuation; - volatile u_char systemId[4]; - volatile u_short globalChecksum; - volatile u_char _11[4]; - volatile u_short maxDatagramSize; - volatile u_short maxFrameSize; - volatile u_char maxRetries; - volatile u_char receiveMode; - volatile u_char priority; - volatile u_char rootOrRepeater; - volatile u_char specifiedRouter[6]; - volatile u_short fastPollPeriod; - volatile u_char pollDecay; - volatile u_char fastPollDelay[2]; - volatile u_char arlThreshold; - volatile u_char arlDecay; - volatile u_char _12[1]; - volatile u_short specRouterTimeout; - volatile u_char _13[5]; - - /* Scrambled Area */ - volatile u_char SID[4]; - volatile u_char encryptionKey[12]; - volatile u_char _14[2]; - volatile u_char waitTime[2]; - volatile u_char lParameter[2]; - volatile u_char _15[3]; - volatile u_short headerSize; - volatile u_short sectionChecksum; - - volatile u_char registrationMode; - volatile u_char registrationFill; - volatile u_short pollPeriod; - volatile u_short refreshPeriod; - volatile u_char name[16]; - volatile u_char NID[6]; - volatile u_char localTalkAddress; - volatile u_char codeFormat; - volatile u_char numChannels; - volatile u_char channel1; - volatile u_char channel2; - volatile u_char channel3; - volatile u_char channel4; - volatile u_char SSCode[59]; - - volatile u_char _16[0xC0]; - volatile u_short auxCmd; - volatile u_char dumpPtr[4]; - volatile u_char dumpVal; - volatile u_char _17[0x6A]; - volatile u_char wireTest; - volatile u_char _18[14]; - - /* Statistics Block - 0x0300 */ - volatile u_char hostcpuLock; - volatile u_char lancpuLock; - volatile u_char resetTime[18]; - - volatile u_char numDatagramsTransmitted[4]; - volatile u_char numReTransmissions[4]; - volatile u_char numFramesDiscarded[4]; - volatile u_char numDatagramsReceived[4]; - volatile u_char numDuplicateReceivedFrames[4]; - volatile u_char numDatagramsDiscarded[4]; - - volatile u_short maxNumReTransmitDatagram; - volatile u_short maxNumReTransmitFrames; - volatile u_short maxNumConsecutiveDuplicateFrames; - /* misaligned here so we have to go to characters */ - - volatile u_char numBytesTransmitted[4]; - volatile u_char numBytesReceived[4]; - volatile u_char numCRCErrors[4]; - volatile u_char numLengthErrors[4]; - volatile u_char numAbortErrors[4]; - volatile u_char numTXUnderruns[4]; - volatile u_char numRXOverruns[4]; - volatile u_char numHoldOffs[4]; - volatile u_char numFramesTransmitted[4]; - volatile u_char numFramesReceived[4]; - volatile u_char numReceiveFramesLost[4]; - volatile u_char numRXBufferOverflows[4]; - volatile u_char numFramesDiscardedAddrMismatch[4]; - volatile u_char numFramesDiscardedSIDMismatch[4]; - volatile u_char numPollsTransmistted[4]; - volatile u_char numPollAcknowledges[4]; - volatile u_char numStatusTimeouts[4]; - volatile u_char numNACKReceived[4]; - - volatile u_char _19[0x86]; - - volatile u_char txBuffer[0x800]; - volatile u_char rxBuffer[0x800]; - - volatile u_char _20[0x800]; - volatile u_char _21[0x3fb]; - volatile u_char configStatus; - volatile u_char _22; - volatile u_char progIOCtrl; - volatile u_char shareMBase; - volatile u_char controlRegister; -}; - -struct arlan_conf_stru { - int spreadingCode; - int channelSet; - int channelNumber; - int scramblingDisable; - int txAttenuation; - int systemId; - int maxDatagramSize; - int maxFrameSize; - int maxRetries; - int receiveMode; - int priority; - int rootOrRepeater; - int SID; - int radioNodeId; - int registrationMode; - int registrationFill; - int localTalkAddress; - int codeFormat; - int numChannels; - int channel1; - int channel2; - int channel3; - int channel4; - int txClear; - int txRetries; - int txRouting; - int txScrambled; - int rxParameter; - int txTimeoutMs; - int txAckTimeoutMs; - int waitCardTimeout; - int waitTime; - int lParameter; - int _15; - int headerSize; - int retries; - int tx_delay_ms; - int waitReTransmitPacketMaxSize; - int ReTransmitPacketMaxSize; - int fastReTransCount; - int driverRetransmissions; - int registrationInterrupts; - int hardwareType; - int radioType; - int writeRadioType; - int writeEEPROM; - char siteName[17]; - int measure_rate; - int in_speed; - int out_speed; - int in_speed10; - int out_speed10; - int in_speed_max; - int out_speed_max; - int pre_Command_Wait; - int rx_tweak1; - int rx_tweak2; - int tx_queue_len; -}; - -extern struct arlan_conf_stru arlan_conf[MAX_ARLANS]; - -struct TxParam -{ - volatile short offset; - volatile short length; - volatile u_char dest[6]; - volatile unsigned char clear; - volatile unsigned char retries; - volatile unsigned char routing; - volatile unsigned char scrambled; -}; - -#define TX_RING_SIZE 2 -/* Information that need to be kept for each board. */ -struct arlan_private { - struct arlan_shmem __iomem * card; - struct arlan_shmem * conf; - - struct arlan_conf_stru * Conf; - int bad; - int reset; - unsigned long lastReset; - struct timer_list timer; - struct timer_list tx_delay_timer; - struct timer_list tx_retry_timer; - struct timer_list rx_check_timer; - - int registrationLostCount; - int reRegisterExp; - int irq_test_done; - - struct TxParam txRing[TX_RING_SIZE]; - char reTransmitBuff[0x800]; - int txLast; - unsigned ReTransmitRequested; - unsigned long tx_done_delayed; - unsigned long registrationLastSeen; - - unsigned long tx_last_sent; - unsigned long tx_last_cleared; - unsigned long retransmissions; - unsigned long interrupt_ack_requested; - spinlock_t lock; - unsigned long waiting_command_mask; - unsigned long card_polling_interval; - unsigned long last_command_buff_free_time; - - int under_reset; - int under_config; - int rx_command_given; - int tx_command_given; - unsigned long interrupt_processing_active; - unsigned long last_rx_int_ack_time; - unsigned long in_bytes; - unsigned long out_bytes; - unsigned long in_time; - unsigned long out_time; - unsigned long in_time10; - unsigned long out_time10; - unsigned long in_bytes10; - unsigned long out_bytes10; - int init_etherdev_alloc; -}; - - - -#define ARLAN_CLEAR 0x00 -#define ARLAN_RESET 0x01 -#define ARLAN_CHANNEL_ATTENTION 0x02 -#define ARLAN_INTERRUPT_ENABLE 0x04 -#define ARLAN_CLEAR_INTERRUPT 0x08 -#define ARLAN_POWER 0x40 -#define ARLAN_ACCESS 0x80 - -#define ARLAN_COM_CONF 0x01 -#define ARLAN_COM_RX_ENABLE 0x03 -#define ARLAN_COM_RX_ABORT 0x04 -#define ARLAN_COM_TX_ENABLE 0x05 -#define ARLAN_COM_TX_ABORT 0x06 -#define ARLAN_COM_NOP 0x07 -#define ARLAN_COM_STANDBY 0x08 -#define ARLAN_COM_ACTIVATE 0x09 -#define ARLAN_COM_GOTO_SLOW_POLL 0x0a -#define ARLAN_COM_INT 0x80 - - -#define TXLAST(dev) (((struct arlan_private *)netdev_priv(dev))->txRing[((struct arlan_private *)netdev_priv(dev))->txLast]) -#define TXHEAD(dev) (((struct arlan_private *)netdev_priv(dev))->txRing[0]) -#define TXTAIL(dev) (((struct arlan_private *)netdev_priv(dev))->txRing[1]) - -#define TXBuffStart(dev) offsetof(struct arlan_shmem, txBuffer) -#define TXBuffEnd(dev) offsetof(struct arlan_shmem, xxBuffer) - -#define READSHM(to,from,atype) {\ - atype tmp;\ - memcpy_fromio(&(tmp),&(from),sizeof(atype));\ - to = tmp;\ - } - -#define READSHMEM(from,atype)\ - atype from; \ - READSHM(from, arlan->from, atype); - -#define WRITESHM(to,from,atype) \ - { atype tmpSHM = from;\ - memcpy_toio(&(to),&tmpSHM,sizeof(atype));\ - } - -#define DEBUGSHM(levelSHM,stringSHM,stuff,atype) \ - { atype tmpSHM; \ - memcpy_fromio(&tmpSHM,&(stuff),sizeof(atype));\ - IFDEBUG(levelSHM) printk(stringSHM,tmpSHM);\ - } - -#define WRITESHMB(to, val) \ - writeb(val,&(to)) -#define READSHMB(to) \ - readb(&(to)) -#define WRITESHMS(to, val) \ - writew(val,&(to)) -#define READSHMS(to) \ - readw(&(to)) -#define WRITESHMI(to, val) \ - writel(val,&(to)) -#define READSHMI(to) \ - readl(&(to)) - - - - - -#define registrationBad(dev)\ - ( ( READSHMB(((struct arlan_private *)netdev_priv(dev))->card->registrationMode) > 0) && \ - ( READSHMB(((struct arlan_private *)netdev_priv(dev))->card->registrationStatus) == 0) ) - - -#define readControlRegister(dev)\ - READSHMB(((struct arlan_private *)netdev_priv(dev))->card->cntrlRegImage) - -#define writeControlRegister(dev, v){\ - WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->cntrlRegImage ,((v) &0xF) );\ - WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->controlRegister ,(v) );} - - -#define arlan_interrupt_lancpu(dev) {\ - int cr; \ - \ - cr = readControlRegister(dev);\ - if (cr & ARLAN_CHANNEL_ATTENTION){ \ - writeControlRegister(dev, (cr & ~ARLAN_CHANNEL_ATTENTION));\ - }else \ - writeControlRegister(dev, (cr | ARLAN_CHANNEL_ATTENTION));\ -} - -#define clearChannelAttention(dev){ \ - writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_CHANNEL_ATTENTION);} -#define setHardwareReset(dev) {\ - writeControlRegister(dev,readControlRegister(dev) | ARLAN_RESET);} -#define clearHardwareReset(dev) {\ - writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_RESET);} -#define setInterruptEnable(dev){\ - writeControlRegister(dev,readControlRegister(dev) | ARLAN_INTERRUPT_ENABLE) ;} -#define clearInterruptEnable(dev){\ - writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_INTERRUPT_ENABLE) ;} -#define setClearInterrupt(dev){\ - writeControlRegister(dev,readControlRegister(dev) | ARLAN_CLEAR_INTERRUPT) ;} -#define clearClearInterrupt(dev){\ - writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_CLEAR_INTERRUPT);} -#define setPowerOff(dev){\ - writeControlRegister(dev,readControlRegister(dev) | (ARLAN_POWER && ARLAN_ACCESS));\ - writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_ACCESS);} -#define setPowerOn(dev){\ - writeControlRegister(dev,readControlRegister(dev) & ~(ARLAN_POWER)); } -#define arlan_lock_card_access(dev){\ - writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_ACCESS);} -#define arlan_unlock_card_access(dev){\ - writeControlRegister(dev,readControlRegister(dev) | ARLAN_ACCESS ); } - - - - -#define ARLAN_COMMAND_RX 0x000001 -#define ARLAN_COMMAND_NOOP 0x000002 -#define ARLAN_COMMAND_NOOPINT 0x000004 -#define ARLAN_COMMAND_TX 0x000008 -#define ARLAN_COMMAND_CONF 0x000010 -#define ARLAN_COMMAND_RESET 0x000020 -#define ARLAN_COMMAND_TX_ABORT 0x000040 -#define ARLAN_COMMAND_RX_ABORT 0x000080 -#define ARLAN_COMMAND_POWERDOWN 0x000100 -#define ARLAN_COMMAND_POWERUP 0x000200 -#define ARLAN_COMMAND_SLOW_POLL 0x000400 -#define ARLAN_COMMAND_ACTIVATE 0x000800 -#define ARLAN_COMMAND_INT_ACK 0x001000 -#define ARLAN_COMMAND_INT_ENABLE 0x002000 -#define ARLAN_COMMAND_WAIT_NOW 0x004000 -#define ARLAN_COMMAND_LONG_WAIT_NOW 0x008000 -#define ARLAN_COMMAND_STANDBY 0x010000 -#define ARLAN_COMMAND_INT_RACK 0x020000 -#define ARLAN_COMMAND_INT_RENABLE 0x040000 -#define ARLAN_COMMAND_CONF_WAIT 0x080000 -#define ARLAN_COMMAND_TBUSY_CLEAR 0x100000 -#define ARLAN_COMMAND_CLEAN_AND_CONF (ARLAN_COMMAND_TX_ABORT\ - | ARLAN_COMMAND_RX_ABORT\ - | ARLAN_COMMAND_CONF) -#define ARLAN_COMMAND_CLEAN_AND_RESET (ARLAN_COMMAND_TX_ABORT\ - | ARLAN_COMMAND_RX_ABORT\ - | ARLAN_COMMAND_RESET) - - - -#define ARLAN_DEBUG_CHAIN_LOCKS 0x00001 -#define ARLAN_DEBUG_RESET 0x00002 -#define ARLAN_DEBUG_TIMING 0x00004 -#define ARLAN_DEBUG_CARD_STATE 0x00008 -#define ARLAN_DEBUG_TX_CHAIN 0x00010 -#define ARLAN_DEBUG_MULTICAST 0x00020 -#define ARLAN_DEBUG_HEADER_DUMP 0x00040 -#define ARLAN_DEBUG_INTERRUPT 0x00080 -#define ARLAN_DEBUG_STARTUP 0x00100 -#define ARLAN_DEBUG_SHUTDOWN 0x00200 - diff --git a/drivers/net/wireless/ath/Kconfig b/drivers/net/wireless/ath/Kconfig index 6ce86cb..4e7a7fd 100644 --- a/drivers/net/wireless/ath/Kconfig +++ b/drivers/net/wireless/ath/Kconfig @@ -1,6 +1,5 @@ menuconfig ATH_COMMON tristate "Atheros Wireless Cards" - depends on WLAN_80211 depends on CFG80211 ---help--- This will enable the support for the Atheros wireless drivers. diff --git a/drivers/net/wireless/ath/ar9170/Kconfig b/drivers/net/wireless/ath/ar9170/Kconfig index 05918f1..d7a4799 100644 --- a/drivers/net/wireless/ath/ar9170/Kconfig +++ b/drivers/net/wireless/ath/ar9170/Kconfig @@ -1,6 +1,6 @@ config AR9170_USB tristate "Atheros AR9170 802.11n USB support" - depends on USB && MAC80211 && WLAN_80211 + depends on USB && MAC80211 select FW_LOADER help This is a driver for the Atheros "otus" 802.11n USB devices. diff --git a/drivers/net/wireless/ath/ath5k/Kconfig b/drivers/net/wireless/ath/ath5k/Kconfig index 06d0066..eb83b7b 100644 --- a/drivers/net/wireless/ath/ath5k/Kconfig +++ b/drivers/net/wireless/ath/ath5k/Kconfig @@ -1,6 +1,6 @@ config ATH5K tristate "Atheros 5xxx wireless cards support" - depends on PCI && MAC80211 && WLAN_80211 + depends on PCI && MAC80211 select MAC80211_LEDS select LEDS_CLASS select NEW_LEDS diff --git a/drivers/net/wireless/ath/ath5k/led.c b/drivers/net/wireless/ath/ath5k/led.c index b767c3b..7ce98bd 100644 --- a/drivers/net/wireless/ath/ath5k/led.c +++ b/drivers/net/wireless/ath/ath5k/led.c @@ -59,6 +59,8 @@ static const struct pci_device_id ath5k_led_devices[] = { { ATH_SDEVICE(PCI_VENDOR_ID_COMPAQ, PCI_ANY_ID), ATH_LED(1, 1) }, /* Acer Aspire One A150 (maximlevitsky@gmail.com) */ { ATH_SDEVICE(PCI_VENDOR_ID_FOXCONN, 0xe008), ATH_LED(3, 0) }, + /* Acer Aspire One AO531h AO751h (keng-yu.lin@canonical.com) */ + { ATH_SDEVICE(PCI_VENDOR_ID_FOXCONN, 0xe00d), ATH_LED(3, 0) }, /* Acer Ferrari 5000 (russ.dill@gmail.com) */ { ATH_SDEVICE(PCI_VENDOR_ID_AMBIT, 0x0422), ATH_LED(1, 1) }, /* E-machines E510 (tuliom@gmail.com) */ diff --git a/drivers/net/wireless/ath/ath9k/Kconfig b/drivers/net/wireless/ath/ath9k/Kconfig index 99ce066..b735fb3 100644 --- a/drivers/net/wireless/ath/ath9k/Kconfig +++ b/drivers/net/wireless/ath/ath9k/Kconfig @@ -3,7 +3,7 @@ config ATH9K_HW config ATH9K tristate "Atheros 802.11n wireless cards support" - depends on PCI && MAC80211 && WLAN_80211 + depends on PCI && MAC80211 select ATH9K_HW select MAC80211_LEDS select LEDS_CLASS diff --git a/drivers/net/wireless/ath/ath9k/ahb.c b/drivers/net/wireless/ath/ath9k/ahb.c index 25531f2..329e6bc 100644 --- a/drivers/net/wireless/ath/ath9k/ahb.c +++ b/drivers/net/wireless/ath/ath9k/ahb.c @@ -69,6 +69,7 @@ static int ath_ahb_probe(struct platform_device *pdev) int irq; int ret = 0; struct ath_hw *ah; + char hw_name[64]; if (!pdev->dev.platform_data) { dev_err(&pdev->dev, "no platform data specified\n"); @@ -133,14 +134,11 @@ static int ath_ahb_probe(struct platform_device *pdev) } ah = sc->sc_ah; + ath9k_hw_name(ah, hw_name, sizeof(hw_name)); printk(KERN_INFO - "%s: Atheros AR%s MAC/BB Rev:%x, " - "AR%s RF Rev:%x, mem=0x%lx, irq=%d\n", + "%s: %s mem=0x%lx, irq=%d\n", wiphy_name(hw->wiphy), - ath_mac_bb_name(ah->hw_version.macVersion), - ah->hw_version.macRev, - ath_rf_name((ah->hw_version.analog5GhzRev & AR_RADIO_SREV_MAJOR)), - ah->hw_version.phyRev, + hw_name, (unsigned long)mem, irq); return 0; diff --git a/drivers/net/wireless/ath/ath9k/calib.c b/drivers/net/wireless/ath/ath9k/calib.c index 551f880..238a574 100644 --- a/drivers/net/wireless/ath/ath9k/calib.c +++ b/drivers/net/wireless/ath/ath9k/calib.c @@ -877,7 +877,7 @@ static void ath9k_hw_9271_pa_cal(struct ath_hw *ah, bool is_reset) REG_RMW_FIELD(ah, AR9285_AN_RF2G6, AR9271_AN_RF2G6_OFFS, 0); /* find off_6_1; */ - for (i = 6; i >= 0; i--) { + for (i = 6; i > 0; i--) { regVal = REG_READ(ah, 0x7834); regVal |= (1 << (20 + i)); REG_WRITE(ah, 0x7834, regVal); diff --git a/drivers/net/wireless/ath/ath9k/eeprom_4k.c b/drivers/net/wireless/ath/ath9k/eeprom_4k.c index 58167d8..68db166 100644 --- a/drivers/net/wireless/ath/ath9k/eeprom_4k.c +++ b/drivers/net/wireless/ath/ath9k/eeprom_4k.c @@ -1112,6 +1112,10 @@ static void ath9k_hw_4k_set_board_values(struct ath_hw *ah, REG_RMW_FIELD(ah, AR_PHY_RF_CTL3, AR_PHY_TX_END_TO_A2_RX_ON, pModal->txEndToRxOn); + + if (AR_SREV_9271_10(ah)) + REG_RMW_FIELD(ah, AR_PHY_RF_CTL3, AR_PHY_TX_END_TO_A2_RX_ON, + pModal->txEndToRxOn); REG_RMW_FIELD(ah, AR_PHY_CCA, AR9280_PHY_CCA_THRESH62, pModal->thresh62); REG_RMW_FIELD(ah, AR_PHY_EXT_CCA0, AR_PHY_EXT_CCA0_THRESH62, diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c index cab17c6..111ff04 100644 --- a/drivers/net/wireless/ath/ath9k/hw.c +++ b/drivers/net/wireless/ath/ath9k/hw.c @@ -30,8 +30,6 @@ static void ath9k_hw_set_regs(struct ath_hw *ah, struct ath9k_channel *chan); static u32 ath9k_hw_ini_fixup(struct ath_hw *ah, struct ar5416_eeprom_def *pEepData, u32 reg, u32 value); -static void ath9k_hw_9280_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan); -static void ath9k_hw_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan); MODULE_AUTHOR("Atheros Communications"); MODULE_DESCRIPTION("Support for Atheros 802.11n wireless LAN cards."); @@ -454,21 +452,6 @@ static void ath9k_hw_init_defaults(struct ath_hw *ah) ah->power_mode = ATH9K_PM_UNDEFINED; } -static int ath9k_hw_rfattach(struct ath_hw *ah) -{ - bool rfStatus = false; - int ecode = 0; - - rfStatus = ath9k_hw_init_rf(ah, &ecode); - if (!rfStatus) { - ath_print(ath9k_hw_common(ah), ATH_DBG_FATAL, - "RF setup failed, status: %u\n", ecode); - return ecode; - } - - return 0; -} - static int ath9k_hw_rf_claim(struct ath_hw *ah) { u32 val; @@ -585,9 +568,15 @@ static int ath9k_hw_post_init(struct ath_hw *ah) ah->eep_ops->get_eeprom_ver(ah), ah->eep_ops->get_eeprom_rev(ah)); - ecode = ath9k_hw_rfattach(ah); - if (ecode != 0) - return ecode; + if (!AR_SREV_9280_10_OR_LATER(ah)) { + ecode = ath9k_hw_rf_alloc_ext_banks(ah); + if (ecode) { + ath_print(ath9k_hw_common(ah), ATH_DBG_FATAL, + "Failed allocating banks for " + "external radio\n"); + return ecode; + } + } if (!AR_SREV_9100(ah)) { ath9k_hw_ani_setup(ah); @@ -662,10 +651,13 @@ static void ath9k_hw_init_cal_settings(struct ath_hw *ah) static void ath9k_hw_init_mode_regs(struct ath_hw *ah) { if (AR_SREV_9271(ah)) { - INIT_INI_ARRAY(&ah->iniModes, ar9271Modes_9271_1_0, - ARRAY_SIZE(ar9271Modes_9271_1_0), 6); - INIT_INI_ARRAY(&ah->iniCommon, ar9271Common_9271_1_0, - ARRAY_SIZE(ar9271Common_9271_1_0), 2); + INIT_INI_ARRAY(&ah->iniModes, ar9271Modes_9271, + ARRAY_SIZE(ar9271Modes_9271), 6); + INIT_INI_ARRAY(&ah->iniCommon, ar9271Common_9271, + ARRAY_SIZE(ar9271Common_9271), 2); + INIT_INI_ARRAY(&ah->iniModes_9271_1_0_only, + ar9271Modes_9271_1_0_only, + ARRAY_SIZE(ar9271Modes_9271_1_0_only), 6); return; } @@ -957,8 +949,14 @@ int ath9k_hw_init(struct ath_hw *ah) ath9k_hw_init_cal_settings(ah); ah->ani_function = ATH9K_ANI_ALL; - if (AR_SREV_9280_10_OR_LATER(ah)) + if (AR_SREV_9280_10_OR_LATER(ah)) { ah->ani_function &= ~ATH9K_ANI_NOISE_IMMUNITY_LEVEL; + ah->ath9k_hw_rf_set_freq = &ath9k_hw_ar9280_set_channel; + ah->ath9k_hw_spur_mitigate_freq = &ath9k_hw_9280_spur_mitigate; + } else { + ah->ath9k_hw_rf_set_freq = &ath9k_hw_set_channel; + ah->ath9k_hw_spur_mitigate_freq = &ath9k_hw_spur_mitigate; + } ath9k_hw_init_mode_regs(ah); @@ -1037,6 +1035,22 @@ static void ath9k_hw_init_qos(struct ath_hw *ah) REG_WRITE(ah, AR_TXOP_12_15, 0xFFFFFFFF); } +static void ath9k_hw_change_target_baud(struct ath_hw *ah, u32 freq, u32 baud) +{ + u32 lcr; + u32 baud_divider = freq * 1000 * 1000 / 16 / baud; + + lcr = REG_READ(ah , 0x5100c); + lcr |= 0x80; + + REG_WRITE(ah, 0x5100c, lcr); + REG_WRITE(ah, 0x51004, (baud_divider >> 8)); + REG_WRITE(ah, 0x51000, (baud_divider & 0xff)); + + lcr &= ~0x80; + REG_WRITE(ah, 0x5100c, lcr); +} + static void ath9k_hw_init_pll(struct ath_hw *ah, struct ath9k_channel *chan) { @@ -1100,6 +1114,26 @@ static void ath9k_hw_init_pll(struct ath_hw *ah, } REG_WRITE(ah, AR_RTC_PLL_CONTROL, pll); + /* Switch the core clock for ar9271 to 117Mhz */ + if (AR_SREV_9271(ah)) { + if ((pll == 0x142c) || (pll == 0x2850) ) { + udelay(500); + /* set CLKOBS to output AHB clock */ + REG_WRITE(ah, 0x7020, 0xe); + /* + * 0x304: 117Mhz, ahb_ratio: 1x1 + * 0x306: 40Mhz, ahb_ratio: 1x1 + */ + REG_WRITE(ah, 0x50040, 0x304); + /* + * makes adjustments for the baud dividor to keep the + * targetted baud rate based on the used core clock. + */ + ath9k_hw_change_target_baud(ah, AR9271_CORE_CLOCK, + AR9271_TARGET_BAUD_RATE); + } + } + udelay(RTC_PLL_SETTLE_DELAY); REG_WRITE(ah, AR_RTC_SLEEP_CLK, AR_RTC_FORCE_DERIVED_CLK); @@ -1252,7 +1286,8 @@ void ath9k_hw_detach(struct ath_hw *ah) ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP); free_hw: - ath9k_hw_rf_free(ah); + if (!AR_SREV_9280_10_OR_LATER(ah)) + ath9k_hw_rf_free_ext_banks(ah); kfree(ah); ah = NULL; } @@ -1274,7 +1309,8 @@ static void ath9k_hw_override_ini(struct ath_hw *ah, * AR9271 1.1 */ if (AR_SREV_9271_10(ah)) { - val = REG_READ(ah, AR_PHY_SPECTRAL_SCAN) | AR_PHY_SPECTRAL_SCAN_ENABLE; + val = REG_READ(ah, AR_PHY_SPECTRAL_SCAN) | + AR_PHY_SPECTRAL_SCAN_ENABLE; REG_WRITE(ah, AR_PHY_SPECTRAL_SCAN, val); } else if (AR_SREV_9271_11(ah)) @@ -1489,7 +1525,11 @@ static int ath9k_hw_process_ini(struct ath_hw *ah, DO_DELAY(regWrites); } - ath9k_hw_write_regs(ah, modesIndex, freqIndex, regWrites); + ath9k_hw_write_regs(ah, freqIndex, regWrites); + + if (AR_SREV_9271_10(ah)) + REG_WRITE_ARRAY(&ah->iniModes_9271_1_0_only, + modesIndex, regWrites); if (AR_SREV_9280_20(ah) && IS_CHAN_A_5MHZ_SPACED(chan)) { REG_WRITE_ARRAY(&ah->iniModesAdditional, modesIndex, @@ -1832,6 +1872,7 @@ static bool ath9k_hw_channel_change(struct ath_hw *ah, struct ath_common *common = ath9k_hw_common(ah); struct ieee80211_channel *channel = chan->chan; u32 synthDelay, qnum; + int r; for (qnum = 0; qnum < AR_NUM_QCU; qnum++) { if (ath9k_hw_numtxpending(ah, qnum)) { @@ -1852,14 +1893,11 @@ static bool ath9k_hw_channel_change(struct ath_hw *ah, ath9k_hw_set_regs(ah, chan); - if (AR_SREV_9280_10_OR_LATER(ah)) { - ath9k_hw_ar9280_set_channel(ah, chan); - } else { - if (!(ath9k_hw_set_channel(ah, chan))) { - ath_print(common, ATH_DBG_FATAL, - "Failed to set channel\n"); - return false; - } + r = ah->ath9k_hw_rf_set_freq(ah, chan); + if (r) { + ath_print(common, ATH_DBG_FATAL, + "Failed to set channel\n"); + return false; } ah->eep_ops->set_txpower(ah, chan, @@ -1882,10 +1920,7 @@ static bool ath9k_hw_channel_change(struct ath_hw *ah, if (IS_CHAN_OFDM(chan) || IS_CHAN_HT(chan)) ath9k_hw_set_delta_slope(ah, chan); - if (AR_SREV_9280_10_OR_LATER(ah)) - ath9k_hw_9280_spur_mitigate(ah, chan); - else - ath9k_hw_spur_mitigate(ah, chan); + ah->ath9k_hw_spur_mitigate_freq(ah, chan); if (!chan->oneTimeCalsDone) chan->oneTimeCalsDone = true; @@ -1893,457 +1928,6 @@ static bool ath9k_hw_channel_change(struct ath_hw *ah, return true; } -static void ath9k_hw_9280_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan) -{ - int bb_spur = AR_NO_SPUR; - int freq; - int bin, cur_bin; - int bb_spur_off, spur_subchannel_sd; - int spur_freq_sd; - int spur_delta_phase; - int denominator; - int upper, lower, cur_vit_mask; - int tmp, newVal; - int i; - int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8, - AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60 - }; - int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10, - AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60 - }; - int inc[4] = { 0, 100, 0, 0 }; - struct chan_centers centers; - - int8_t mask_m[123]; - int8_t mask_p[123]; - int8_t mask_amt; - int tmp_mask; - int cur_bb_spur; - bool is2GHz = IS_CHAN_2GHZ(chan); - - memset(&mask_m, 0, sizeof(int8_t) * 123); - memset(&mask_p, 0, sizeof(int8_t) * 123); - - ath9k_hw_get_channel_centers(ah, chan, ¢ers); - freq = centers.synth_center; - - ah->config.spurmode = SPUR_ENABLE_EEPROM; - for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) { - cur_bb_spur = ah->eep_ops->get_spur_channel(ah, i, is2GHz); - - if (is2GHz) - cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_2GHZ; - else - cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_5GHZ; - - if (AR_NO_SPUR == cur_bb_spur) - break; - cur_bb_spur = cur_bb_spur - freq; - - if (IS_CHAN_HT40(chan)) { - if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT40) && - (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT40)) { - bb_spur = cur_bb_spur; - break; - } - } else if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT20) && - (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT20)) { - bb_spur = cur_bb_spur; - break; - } - } - - if (AR_NO_SPUR == bb_spur) { - REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, - AR_PHY_FORCE_CLKEN_CCK_MRC_MUX); - return; - } else { - REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, - AR_PHY_FORCE_CLKEN_CCK_MRC_MUX); - } - - bin = bb_spur * 320; - - tmp = REG_READ(ah, AR_PHY_TIMING_CTRL4(0)); - - newVal = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI | - AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER | - AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK | - AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK); - REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0), newVal); - - newVal = (AR_PHY_SPUR_REG_MASK_RATE_CNTL | - AR_PHY_SPUR_REG_ENABLE_MASK_PPM | - AR_PHY_SPUR_REG_MASK_RATE_SELECT | - AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI | - SM(SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH)); - REG_WRITE(ah, AR_PHY_SPUR_REG, newVal); - - if (IS_CHAN_HT40(chan)) { - if (bb_spur < 0) { - spur_subchannel_sd = 1; - bb_spur_off = bb_spur + 10; - } else { - spur_subchannel_sd = 0; - bb_spur_off = bb_spur - 10; - } - } else { - spur_subchannel_sd = 0; - bb_spur_off = bb_spur; - } - - if (IS_CHAN_HT40(chan)) - spur_delta_phase = - ((bb_spur * 262144) / - 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE; - else - spur_delta_phase = - ((bb_spur * 524288) / - 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE; - - denominator = IS_CHAN_2GHZ(chan) ? 44 : 40; - spur_freq_sd = ((bb_spur_off * 2048) / denominator) & 0x3ff; - - newVal = (AR_PHY_TIMING11_USE_SPUR_IN_AGC | - SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) | - SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE)); - REG_WRITE(ah, AR_PHY_TIMING11, newVal); - - newVal = spur_subchannel_sd << AR_PHY_SFCORR_SPUR_SUBCHNL_SD_S; - REG_WRITE(ah, AR_PHY_SFCORR_EXT, newVal); - - cur_bin = -6000; - upper = bin + 100; - lower = bin - 100; - - for (i = 0; i < 4; i++) { - int pilot_mask = 0; - int chan_mask = 0; - int bp = 0; - for (bp = 0; bp < 30; bp++) { - if ((cur_bin > lower) && (cur_bin < upper)) { - pilot_mask = pilot_mask | 0x1 << bp; - chan_mask = chan_mask | 0x1 << bp; - } - cur_bin += 100; - } - cur_bin += inc[i]; - REG_WRITE(ah, pilot_mask_reg[i], pilot_mask); - REG_WRITE(ah, chan_mask_reg[i], chan_mask); - } - - cur_vit_mask = 6100; - upper = bin + 120; - lower = bin - 120; - - for (i = 0; i < 123; i++) { - if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) { - - /* workaround for gcc bug #37014 */ - volatile int tmp_v = abs(cur_vit_mask - bin); - - if (tmp_v < 75) - mask_amt = 1; - else - mask_amt = 0; - if (cur_vit_mask < 0) - mask_m[abs(cur_vit_mask / 100)] = mask_amt; - else - mask_p[cur_vit_mask / 100] = mask_amt; - } - cur_vit_mask -= 100; - } - - tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28) - | (mask_m[48] << 26) | (mask_m[49] << 24) - | (mask_m[50] << 22) | (mask_m[51] << 20) - | (mask_m[52] << 18) | (mask_m[53] << 16) - | (mask_m[54] << 14) | (mask_m[55] << 12) - | (mask_m[56] << 10) | (mask_m[57] << 8) - | (mask_m[58] << 6) | (mask_m[59] << 4) - | (mask_m[60] << 2) | (mask_m[61] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask); - REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask); - - tmp_mask = (mask_m[31] << 28) - | (mask_m[32] << 26) | (mask_m[33] << 24) - | (mask_m[34] << 22) | (mask_m[35] << 20) - | (mask_m[36] << 18) | (mask_m[37] << 16) - | (mask_m[48] << 14) | (mask_m[39] << 12) - | (mask_m[40] << 10) | (mask_m[41] << 8) - | (mask_m[42] << 6) | (mask_m[43] << 4) - | (mask_m[44] << 2) | (mask_m[45] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask); - - tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28) - | (mask_m[18] << 26) | (mask_m[18] << 24) - | (mask_m[20] << 22) | (mask_m[20] << 20) - | (mask_m[22] << 18) | (mask_m[22] << 16) - | (mask_m[24] << 14) | (mask_m[24] << 12) - | (mask_m[25] << 10) | (mask_m[26] << 8) - | (mask_m[27] << 6) | (mask_m[28] << 4) - | (mask_m[29] << 2) | (mask_m[30] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask); - - tmp_mask = (mask_m[0] << 30) | (mask_m[1] << 28) - | (mask_m[2] << 26) | (mask_m[3] << 24) - | (mask_m[4] << 22) | (mask_m[5] << 20) - | (mask_m[6] << 18) | (mask_m[7] << 16) - | (mask_m[8] << 14) | (mask_m[9] << 12) - | (mask_m[10] << 10) | (mask_m[11] << 8) - | (mask_m[12] << 6) | (mask_m[13] << 4) - | (mask_m[14] << 2) | (mask_m[15] << 0); - REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask); - - tmp_mask = (mask_p[15] << 28) - | (mask_p[14] << 26) | (mask_p[13] << 24) - | (mask_p[12] << 22) | (mask_p[11] << 20) - | (mask_p[10] << 18) | (mask_p[9] << 16) - | (mask_p[8] << 14) | (mask_p[7] << 12) - | (mask_p[6] << 10) | (mask_p[5] << 8) - | (mask_p[4] << 6) | (mask_p[3] << 4) - | (mask_p[2] << 2) | (mask_p[1] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask); - - tmp_mask = (mask_p[30] << 28) - | (mask_p[29] << 26) | (mask_p[28] << 24) - | (mask_p[27] << 22) | (mask_p[26] << 20) - | (mask_p[25] << 18) | (mask_p[24] << 16) - | (mask_p[23] << 14) | (mask_p[22] << 12) - | (mask_p[21] << 10) | (mask_p[20] << 8) - | (mask_p[19] << 6) | (mask_p[18] << 4) - | (mask_p[17] << 2) | (mask_p[16] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask); - - tmp_mask = (mask_p[45] << 28) - | (mask_p[44] << 26) | (mask_p[43] << 24) - | (mask_p[42] << 22) | (mask_p[41] << 20) - | (mask_p[40] << 18) | (mask_p[39] << 16) - | (mask_p[38] << 14) | (mask_p[37] << 12) - | (mask_p[36] << 10) | (mask_p[35] << 8) - | (mask_p[34] << 6) | (mask_p[33] << 4) - | (mask_p[32] << 2) | (mask_p[31] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask); - - tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28) - | (mask_p[59] << 26) | (mask_p[58] << 24) - | (mask_p[57] << 22) | (mask_p[56] << 20) - | (mask_p[55] << 18) | (mask_p[54] << 16) - | (mask_p[53] << 14) | (mask_p[52] << 12) - | (mask_p[51] << 10) | (mask_p[50] << 8) - | (mask_p[49] << 6) | (mask_p[48] << 4) - | (mask_p[47] << 2) | (mask_p[46] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask); -} - -static void ath9k_hw_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan) -{ - int bb_spur = AR_NO_SPUR; - int bin, cur_bin; - int spur_freq_sd; - int spur_delta_phase; - int denominator; - int upper, lower, cur_vit_mask; - int tmp, new; - int i; - int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8, - AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60 - }; - int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10, - AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60 - }; - int inc[4] = { 0, 100, 0, 0 }; - - int8_t mask_m[123]; - int8_t mask_p[123]; - int8_t mask_amt; - int tmp_mask; - int cur_bb_spur; - bool is2GHz = IS_CHAN_2GHZ(chan); - - memset(&mask_m, 0, sizeof(int8_t) * 123); - memset(&mask_p, 0, sizeof(int8_t) * 123); - - for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) { - cur_bb_spur = ah->eep_ops->get_spur_channel(ah, i, is2GHz); - if (AR_NO_SPUR == cur_bb_spur) - break; - cur_bb_spur = cur_bb_spur - (chan->channel * 10); - if ((cur_bb_spur > -95) && (cur_bb_spur < 95)) { - bb_spur = cur_bb_spur; - break; - } - } - - if (AR_NO_SPUR == bb_spur) - return; - - bin = bb_spur * 32; - - tmp = REG_READ(ah, AR_PHY_TIMING_CTRL4(0)); - new = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI | - AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER | - AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK | - AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK); - - REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0), new); - - new = (AR_PHY_SPUR_REG_MASK_RATE_CNTL | - AR_PHY_SPUR_REG_ENABLE_MASK_PPM | - AR_PHY_SPUR_REG_MASK_RATE_SELECT | - AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI | - SM(SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH)); - REG_WRITE(ah, AR_PHY_SPUR_REG, new); - - spur_delta_phase = ((bb_spur * 524288) / 100) & - AR_PHY_TIMING11_SPUR_DELTA_PHASE; - - denominator = IS_CHAN_2GHZ(chan) ? 440 : 400; - spur_freq_sd = ((bb_spur * 2048) / denominator) & 0x3ff; - - new = (AR_PHY_TIMING11_USE_SPUR_IN_AGC | - SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) | - SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE)); - REG_WRITE(ah, AR_PHY_TIMING11, new); - - cur_bin = -6000; - upper = bin + 100; - lower = bin - 100; - - for (i = 0; i < 4; i++) { - int pilot_mask = 0; - int chan_mask = 0; - int bp = 0; - for (bp = 0; bp < 30; bp++) { - if ((cur_bin > lower) && (cur_bin < upper)) { - pilot_mask = pilot_mask | 0x1 << bp; - chan_mask = chan_mask | 0x1 << bp; - } - cur_bin += 100; - } - cur_bin += inc[i]; - REG_WRITE(ah, pilot_mask_reg[i], pilot_mask); - REG_WRITE(ah, chan_mask_reg[i], chan_mask); - } - - cur_vit_mask = 6100; - upper = bin + 120; - lower = bin - 120; - - for (i = 0; i < 123; i++) { - if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) { - - /* workaround for gcc bug #37014 */ - volatile int tmp_v = abs(cur_vit_mask - bin); - - if (tmp_v < 75) - mask_amt = 1; - else - mask_amt = 0; - if (cur_vit_mask < 0) - mask_m[abs(cur_vit_mask / 100)] = mask_amt; - else - mask_p[cur_vit_mask / 100] = mask_amt; - } - cur_vit_mask -= 100; - } - - tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28) - | (mask_m[48] << 26) | (mask_m[49] << 24) - | (mask_m[50] << 22) | (mask_m[51] << 20) - | (mask_m[52] << 18) | (mask_m[53] << 16) - | (mask_m[54] << 14) | (mask_m[55] << 12) - | (mask_m[56] << 10) | (mask_m[57] << 8) - | (mask_m[58] << 6) | (mask_m[59] << 4) - | (mask_m[60] << 2) | (mask_m[61] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask); - REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask); - - tmp_mask = (mask_m[31] << 28) - | (mask_m[32] << 26) | (mask_m[33] << 24) - | (mask_m[34] << 22) | (mask_m[35] << 20) - | (mask_m[36] << 18) | (mask_m[37] << 16) - | (mask_m[48] << 14) | (mask_m[39] << 12) - | (mask_m[40] << 10) | (mask_m[41] << 8) - | (mask_m[42] << 6) | (mask_m[43] << 4) - | (mask_m[44] << 2) | (mask_m[45] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask); - - tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28) - | (mask_m[18] << 26) | (mask_m[18] << 24) - | (mask_m[20] << 22) | (mask_m[20] << 20) - | (mask_m[22] << 18) | (mask_m[22] << 16) - | (mask_m[24] << 14) | (mask_m[24] << 12) - | (mask_m[25] << 10) | (mask_m[26] << 8) - | (mask_m[27] << 6) | (mask_m[28] << 4) - | (mask_m[29] << 2) | (mask_m[30] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask); - - tmp_mask = (mask_m[0] << 30) | (mask_m[1] << 28) - | (mask_m[2] << 26) | (mask_m[3] << 24) - | (mask_m[4] << 22) | (mask_m[5] << 20) - | (mask_m[6] << 18) | (mask_m[7] << 16) - | (mask_m[8] << 14) | (mask_m[9] << 12) - | (mask_m[10] << 10) | (mask_m[11] << 8) - | (mask_m[12] << 6) | (mask_m[13] << 4) - | (mask_m[14] << 2) | (mask_m[15] << 0); - REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask); - - tmp_mask = (mask_p[15] << 28) - | (mask_p[14] << 26) | (mask_p[13] << 24) - | (mask_p[12] << 22) | (mask_p[11] << 20) - | (mask_p[10] << 18) | (mask_p[9] << 16) - | (mask_p[8] << 14) | (mask_p[7] << 12) - | (mask_p[6] << 10) | (mask_p[5] << 8) - | (mask_p[4] << 6) | (mask_p[3] << 4) - | (mask_p[2] << 2) | (mask_p[1] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask); - - tmp_mask = (mask_p[30] << 28) - | (mask_p[29] << 26) | (mask_p[28] << 24) - | (mask_p[27] << 22) | (mask_p[26] << 20) - | (mask_p[25] << 18) | (mask_p[24] << 16) - | (mask_p[23] << 14) | (mask_p[22] << 12) - | (mask_p[21] << 10) | (mask_p[20] << 8) - | (mask_p[19] << 6) | (mask_p[18] << 4) - | (mask_p[17] << 2) | (mask_p[16] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask); - - tmp_mask = (mask_p[45] << 28) - | (mask_p[44] << 26) | (mask_p[43] << 24) - | (mask_p[42] << 22) | (mask_p[41] << 20) - | (mask_p[40] << 18) | (mask_p[39] << 16) - | (mask_p[38] << 14) | (mask_p[37] << 12) - | (mask_p[36] << 10) | (mask_p[35] << 8) - | (mask_p[34] << 6) | (mask_p[33] << 4) - | (mask_p[32] << 2) | (mask_p[31] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask); - - tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28) - | (mask_p[59] << 26) | (mask_p[58] << 24) - | (mask_p[57] << 22) | (mask_p[56] << 20) - | (mask_p[55] << 18) | (mask_p[54] << 16) - | (mask_p[53] << 14) | (mask_p[52] << 12) - | (mask_p[51] << 10) | (mask_p[50] << 8) - | (mask_p[49] << 6) | (mask_p[48] << 4) - | (mask_p[47] << 2) | (mask_p[46] << 0); - REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask); - REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask); -} - static void ath9k_enable_rfkill(struct ath_hw *ah) { REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL, @@ -2469,14 +2053,11 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, if (IS_CHAN_OFDM(chan) || IS_CHAN_HT(chan)) ath9k_hw_set_delta_slope(ah, chan); - if (AR_SREV_9280_10_OR_LATER(ah)) - ath9k_hw_9280_spur_mitigate(ah, chan); - else - ath9k_hw_spur_mitigate(ah, chan); - + ah->ath9k_hw_spur_mitigate_freq(ah, chan); ah->eep_ops->set_board_values(ah, chan); - ath9k_hw_decrease_chain_power(ah, chan); + if (AR_SREV_5416(ah)) + ath9k_hw_decrease_chain_power(ah, chan); REG_WRITE(ah, AR_STA_ID0, get_unaligned_le32(common->macaddr)); REG_WRITE(ah, AR_STA_ID1, get_unaligned_le16(common->macaddr + 4) @@ -2497,11 +2078,9 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, REG_WRITE(ah, AR_RSSI_THR, INIT_RSSI_THR); - if (AR_SREV_9280_10_OR_LATER(ah)) - ath9k_hw_ar9280_set_channel(ah, chan); - else - if (!(ath9k_hw_set_channel(ah, chan))) - return -EIO; + r = ah->ath9k_hw_rf_set_freq(ah, chan); + if (r) + return r; for (i = 0; i < AR_NUM_DCU; i++) REG_WRITE(ah, AR_DQCUMASK(i), 1 << i); @@ -4350,3 +3929,89 @@ void ath_gen_timer_isr(struct ath_hw *ah) } } EXPORT_SYMBOL(ath_gen_timer_isr); + +static struct { + u32 version; + const char * name; +} ath_mac_bb_names[] = { + /* Devices with external radios */ + { AR_SREV_VERSION_5416_PCI, "5416" }, + { AR_SREV_VERSION_5416_PCIE, "5418" }, + { AR_SREV_VERSION_9100, "9100" }, + { AR_SREV_VERSION_9160, "9160" }, + /* Single-chip solutions */ + { AR_SREV_VERSION_9280, "9280" }, + { AR_SREV_VERSION_9285, "9285" }, + { AR_SREV_VERSION_9287, "9287" }, + { AR_SREV_VERSION_9271, "9271" }, +}; + +/* For devices with external radios */ +static struct { + u16 version; + const char * name; +} ath_rf_names[] = { + { 0, "5133" }, + { AR_RAD5133_SREV_MAJOR, "5133" }, + { AR_RAD5122_SREV_MAJOR, "5122" }, + { AR_RAD2133_SREV_MAJOR, "2133" }, + { AR_RAD2122_SREV_MAJOR, "2122" } +}; + +/* + * Return the MAC/BB name. "????" is returned if the MAC/BB is unknown. + */ +static const char *ath9k_hw_mac_bb_name(u32 mac_bb_version) +{ + int i; + + for (i=0; i<ARRAY_SIZE(ath_mac_bb_names); i++) { + if (ath_mac_bb_names[i].version == mac_bb_version) { + return ath_mac_bb_names[i].name; + } + } + + return "????"; +} + +/* + * Return the RF name. "????" is returned if the RF is unknown. + * Used for devices with external radios. + */ +static const char *ath9k_hw_rf_name(u16 rf_version) +{ + int i; + + for (i=0; i<ARRAY_SIZE(ath_rf_names); i++) { + if (ath_rf_names[i].version == rf_version) { + return ath_rf_names[i].name; + } + } + + return "????"; +} + +void ath9k_hw_name(struct ath_hw *ah, char *hw_name, size_t len) +{ + int used; + + /* chipsets >= AR9280 are single-chip */ + if (AR_SREV_9280_10_OR_LATER(ah)) { + used = snprintf(hw_name, len, + "Atheros AR%s Rev:%x", + ath9k_hw_mac_bb_name(ah->hw_version.macVersion), + ah->hw_version.macRev); + } + else { + used = snprintf(hw_name, len, + "Atheros AR%s MAC/BB Rev:%x AR%s RF Rev:%x", + ath9k_hw_mac_bb_name(ah->hw_version.macVersion), + ah->hw_version.macRev, + ath9k_hw_rf_name((ah->hw_version.analog5GhzRev & + AR_RADIO_SREV_MAJOR)), + ah->hw_version.phyRev); + } + + hw_name[used] = '\0'; +} +EXPORT_SYMBOL(ath9k_hw_name); diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h index cdaec52..c7b0c4d 100644 --- a/drivers/net/wireless/ath/ath9k/hw.h +++ b/drivers/net/wireless/ath/ath9k/hw.h @@ -148,6 +148,15 @@ enum wireless_mode { ATH9K_MODE_MAX, }; +/** + * ath9k_ant_setting - transmit antenna settings + * + * Configures the antenna setting to use for transmit. + * + * @ATH9K_ANT_VARIABLE: this means transmit on all active antennas + * @ATH9K_ANT_FIXED_A: this means transmit on the first antenna only + * @ATH9K_ANT_FIXED_B: this means transmit on the second antenna only + */ enum ath9k_ant_setting { ATH9K_ANT_VARIABLE = 0, ATH9K_ANT_FIXED_A, @@ -539,7 +548,14 @@ struct ath_hw { DONT_USE_32KHZ, } enable_32kHz_clock; - /* RF */ + /* Callback for radio frequency change */ + int (*ath9k_hw_rf_set_freq)(struct ath_hw *ah, struct ath9k_channel *chan); + + /* Callback for baseband spur frequency */ + void (*ath9k_hw_spur_mitigate_freq)(struct ath_hw *ah, + struct ath9k_channel *chan); + + /* Used to program the radio on non single-chip devices */ u32 *analogBank0Data; u32 *analogBank1Data; u32 *analogBank2Data; @@ -596,6 +612,7 @@ struct ath_hw { struct ar5416IniArray iniModesAdditional; struct ar5416IniArray iniModesRxGain; struct ar5416IniArray iniModesTxGain; + struct ar5416IniArray iniModes_9271_1_0_only; struct ar5416IniArray iniCckfirNormal; struct ar5416IniArray iniCckfirJapan2484; @@ -618,7 +635,6 @@ static inline struct ath_regulatory *ath9k_hw_regulatory(struct ath_hw *ah) const char *ath9k_hw_probe(u16 vendorid, u16 devid); void ath9k_hw_detach(struct ath_hw *ah); int ath9k_hw_init(struct ath_hw *ah); -void ath9k_hw_rf_free(struct ath_hw *ah); int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, bool bChannelChange); void ath9k_hw_fill_cap_info(struct ath_hw *ah); @@ -704,6 +720,8 @@ void ath_gen_timer_free(struct ath_hw *ah, struct ath_gen_timer *timer); void ath_gen_timer_isr(struct ath_hw *hw); u32 ath9k_hw_gettsf32(struct ath_hw *ah); +void ath9k_hw_name(struct ath_hw *ah, char *hw_name, size_t len); + #define ATH_PCIE_CAP_LINK_CTRL 0x70 #define ATH_PCIE_CAP_LINK_L0S 1 #define ATH_PCIE_CAP_LINK_L1 2 diff --git a/drivers/net/wireless/ath/ath9k/initvals.h b/drivers/net/wireless/ath/ath9k/initvals.h index 3ee6658..8a3bf3a 100644 --- a/drivers/net/wireless/ath/ath9k/initvals.h +++ b/drivers/net/wireless/ath/ath9k/initvals.h @@ -6379,8 +6379,8 @@ static const u_int32_t ar9287PciePhy_clkreq_off_L1_9287_1_1[][2] = { }; -/* AR9271 initialization values automaticaly created: 03/23/09 */ -static const u_int32_t ar9271Modes_9271_1_0[][6] = { +/* AR9271 initialization values automaticaly created: 06/04/09 */ +static const u_int32_t ar9271Modes_9271[][6] = { { 0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160, 0x000001e0 }, { 0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c, 0x000001e0 }, { 0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38, 0x00001180 }, @@ -6390,8 +6390,8 @@ static const u_int32_t ar9271Modes_9271_1_0[][6] = { { 0x00008318, 0x00003e80, 0x00007d00, 0x00006880, 0x00003440, 0x00006880 }, { 0x00009804, 0x00000300, 0x000003c4, 0x000003c4, 0x00000300, 0x00000303 }, { 0x00009820, 0x02020200, 0x02020200, 0x02020200, 0x02020200, 0x02020200 }, - { 0x00009824, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e }, - { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 }, + { 0x00009824, 0x01000e0e, 0x01000e0e, 0x01000e0e, 0x01000e0e, 0x01000e0e }, + { 0x00009828, 0x3a020001, 0x3a020001, 0x3a020001, 0x3a020001, 0x3a020001 }, { 0x00009834, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e }, { 0x00009838, 0x00000007, 0x00000007, 0x00000007, 0x00000007, 0x00000007 }, { 0x00009840, 0x206a012e, 0x206a012e, 0x206a012e, 0x206a012e, 0x206a012e }, @@ -6405,6 +6405,7 @@ static const u_int32_t ar9271Modes_9271_1_0[][6] = { { 0x00009864, 0x0000fe00, 0x0000fe00, 0x0001ce00, 0x0001ce00, 0x0001ce00 }, { 0x00009868, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0 }, { 0x0000986c, 0x06903081, 0x06903081, 0x06903881, 0x06903881, 0x06903881 }, + { 0x00009910, 0x30002310, 0x30002310, 0x30002310, 0x30002310, 0x30002310 }, { 0x00009914, 0x000007d0, 0x00000fa0, 0x00001130, 0x00000898, 0x000007d0 }, { 0x00009918, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b, 0x00000016 }, { 0x00009924, 0xd00a8007, 0xd00a8007, 0xd00a800d, 0xd00a800d, 0xd00a800d }, @@ -6415,7 +6416,7 @@ static const u_int32_t ar9271Modes_9271_1_0[][6] = { { 0x000099bc, 0x00000600, 0x00000600, 0x00000c00, 0x00000c00, 0x00000c00 }, { 0x000099c0, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4 }, { 0x000099c4, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77 }, - { 0x000099c8, 0x6af65329, 0x6af65329, 0x6af65329, 0x6af65329, 0x6af65329 }, + { 0x000099c8, 0x6af6532f, 0x6af6532f, 0x6af6532f, 0x6af6532f, 0x6af6532f }, { 0x000099cc, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8 }, { 0x000099d0, 0x00046384, 0x00046384, 0x00046384, 0x00046384, 0x00046384 }, { 0x000099d4, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 }, @@ -6704,7 +6705,7 @@ static const u_int32_t ar9271Modes_9271_1_0[][6] = { { 0x0000a358, 0x7999aa02, 0x7999aa02, 0x7999aa0e, 0x7999aa0e, 0x7999aa0e }, }; -static const u_int32_t ar9271Common_9271_1_0[][2] = { +static const u_int32_t ar9271Common_9271[][2] = { { 0x0000000c, 0x00000000 }, { 0x00000030, 0x00020045 }, { 0x00000034, 0x00000005 }, @@ -6800,7 +6801,7 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x0000803c, 0x00000000 }, { 0x00008048, 0x00000000 }, { 0x00008054, 0x00000000 }, - { 0x00008058, 0x02000000 }, + { 0x00008058, 0x00000000 }, { 0x0000805c, 0x000fc78f }, { 0x00008060, 0x0000000f }, { 0x00008064, 0x00000000 }, @@ -6831,7 +6832,7 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x00008110, 0x00000168 }, { 0x00008118, 0x000100aa }, { 0x0000811c, 0x00003210 }, - { 0x00008120, 0x08f04814 }, + { 0x00008120, 0x08f04810 }, { 0x00008124, 0x00000000 }, { 0x00008128, 0x00000000 }, { 0x0000812c, 0x00000000 }, @@ -6878,7 +6879,7 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x00008258, 0x00000000 }, { 0x0000825c, 0x400000ff }, { 0x00008260, 0x00080922 }, - { 0x00008264, 0xa8a00010 }, + { 0x00008264, 0x88a00010 }, { 0x00008270, 0x00000000 }, { 0x00008274, 0x40000000 }, { 0x00008278, 0x003e4180 }, @@ -6910,7 +6911,7 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x00007814, 0x924934a8 }, { 0x0000781c, 0x00000000 }, { 0x00007820, 0x00000c04 }, - { 0x00007824, 0x00d86bff }, + { 0x00007824, 0x00d8abff }, { 0x00007828, 0x66964300 }, { 0x0000782c, 0x8db6d961 }, { 0x00007830, 0x8db6d96c }, @@ -6944,7 +6945,6 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x00009904, 0x00000000 }, { 0x00009908, 0x00000000 }, { 0x0000990c, 0x00000000 }, - { 0x00009910, 0x30002310 }, { 0x0000991c, 0x10000fff }, { 0x00009920, 0x04900000 }, { 0x00009928, 0x00000001 }, @@ -6958,7 +6958,7 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x00009954, 0x5f3ca3de }, { 0x00009958, 0x0108ecff }, { 0x00009968, 0x000003ce }, - { 0x00009970, 0x192bb515 }, + { 0x00009970, 0x192bb514 }, { 0x00009974, 0x00000000 }, { 0x00009978, 0x00000001 }, { 0x0000997c, 0x00000000 }, @@ -7045,3 +7045,8 @@ static const u_int32_t ar9271Common_9271_1_0[][2] = { { 0x0000d380, 0x7f3c7bba }, { 0x0000d384, 0xf3307ff0 }, }; + +static const u_int32_t ar9271Modes_9271_1_0_only[][6] = { + { 0x00009910, 0x30002311, 0x30002311, 0x30002311, 0x30002311, 0x30002311 }, + { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 }, +}; diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 69cf702..9fefc51 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -3191,64 +3191,6 @@ struct ieee80211_ops ath9k_ops = { .rfkill_poll = ath9k_rfkill_poll_state, }; -static struct { - u32 version; - const char * name; -} ath_mac_bb_names[] = { - { AR_SREV_VERSION_5416_PCI, "5416" }, - { AR_SREV_VERSION_5416_PCIE, "5418" }, - { AR_SREV_VERSION_9100, "9100" }, - { AR_SREV_VERSION_9160, "9160" }, - { AR_SREV_VERSION_9280, "9280" }, - { AR_SREV_VERSION_9285, "9285" }, - { AR_SREV_VERSION_9287, "9287" } -}; - -static struct { - u16 version; - const char * name; -} ath_rf_names[] = { - { 0, "5133" }, - { AR_RAD5133_SREV_MAJOR, "5133" }, - { AR_RAD5122_SREV_MAJOR, "5122" }, - { AR_RAD2133_SREV_MAJOR, "2133" }, - { AR_RAD2122_SREV_MAJOR, "2122" } -}; - -/* - * Return the MAC/BB name. "????" is returned if the MAC/BB is unknown. - */ -const char * -ath_mac_bb_name(u32 mac_bb_version) -{ - int i; - - for (i=0; i<ARRAY_SIZE(ath_mac_bb_names); i++) { - if (ath_mac_bb_names[i].version == mac_bb_version) { - return ath_mac_bb_names[i].name; - } - } - - return "????"; -} - -/* - * Return the RF name. "????" is returned if the RF is unknown. - */ -const char * -ath_rf_name(u16 rf_version) -{ - int i; - - for (i=0; i<ARRAY_SIZE(ath_rf_names); i++) { - if (ath_rf_names[i].version == rf_version) { - return ath_rf_names[i].name; - } - } - - return "????"; -} - static int __init ath9k_init(void) { int error; diff --git a/drivers/net/wireless/ath/ath9k/pci.c b/drivers/net/wireless/ath/ath9k/pci.c index 63059b6..5321f73 100644 --- a/drivers/net/wireless/ath/ath9k/pci.c +++ b/drivers/net/wireless/ath/ath9k/pci.c @@ -114,6 +114,7 @@ static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) u32 val; int ret = 0; struct ath_hw *ah; + char hw_name[64]; if (pci_enable_device(pdev)) return -EIO; @@ -218,14 +219,11 @@ static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) sc->irq = pdev->irq; ah = sc->sc_ah; + ath9k_hw_name(ah, hw_name, sizeof(hw_name)); printk(KERN_INFO - "%s: Atheros AR%s MAC/BB Rev:%x " - "AR%s RF Rev:%x: mem=0x%lx, irq=%d\n", + "%s: %s mem=0x%lx, irq=%d\n", wiphy_name(hw->wiphy), - ath_mac_bb_name(ah->hw_version.macVersion), - ah->hw_version.macRev, - ath_rf_name((ah->hw_version.analog5GhzRev & AR_RADIO_SREV_MAJOR)), - ah->hw_version.phyRev, + hw_name, (unsigned long)mem, pdev->irq); return 0; diff --git a/drivers/net/wireless/ath/ath9k/phy.c b/drivers/net/wireless/ath/ath9k/phy.c index 72a17c4..13ab4d7 100644 --- a/drivers/net/wireless/ath/ath9k/phy.c +++ b/drivers/net/wireless/ath/ath9k/phy.c @@ -14,91 +14,70 @@ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ +/** + * DOC: Programming Atheros 802.11n analog front end radios + * + * AR5416 MAC based PCI devices and AR518 MAC based PCI-Express + * devices have either an external AR2133 analog front end radio for single + * band 2.4 GHz communication or an AR5133 analog front end radio for dual + * band 2.4 GHz / 5 GHz communication. + * + * All devices after the AR5416 and AR5418 family starting with the AR9280 + * have their analog front radios, MAC/BB and host PCIe/USB interface embedded + * into a single-chip and require less programming. + * + * The following single-chips exist with a respective embedded radio: + * + * AR9280 - 11n dual-band 2x2 MIMO for PCIe + * AR9281 - 11n single-band 1x2 MIMO for PCIe + * AR9285 - 11n single-band 1x1 for PCIe + * AR9287 - 11n single-band 2x2 MIMO for PCIe + * + * AR9220 - 11n dual-band 2x2 MIMO for PCI + * AR9223 - 11n single-band 2x2 MIMO for PCI + * + * AR9287 - 11n single-band 1x1 MIMO for USB + */ + #include "hw.h" -void -ath9k_hw_write_regs(struct ath_hw *ah, u32 modesIndex, u32 freqIndex, - int regWrites) +/** + * ath9k_hw_write_regs - ?? + * + * @ah: atheros hardware structure + * @freqIndex: + * @regWrites: + * + * Used for both the chipsets with an external AR2133/AR5133 radios and + * single-chip devices. + */ +void ath9k_hw_write_regs(struct ath_hw *ah, u32 freqIndex, int regWrites) { REG_WRITE_ARRAY(&ah->iniBB_RfGain, freqIndex, regWrites); } -bool -ath9k_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan) -{ - struct ath_common *common = ath9k_hw_common(ah); - u32 channelSel = 0; - u32 bModeSynth = 0; - u32 aModeRefSel = 0; - u32 reg32 = 0; - u16 freq; - struct chan_centers centers; - - ath9k_hw_get_channel_centers(ah, chan, ¢ers); - freq = centers.synth_center; - - if (freq < 4800) { - u32 txctl; - - if (((freq - 2192) % 5) == 0) { - channelSel = ((freq - 672) * 2 - 3040) / 10; - bModeSynth = 0; - } else if (((freq - 2224) % 5) == 0) { - channelSel = ((freq - 704) * 2 - 3040) / 10; - bModeSynth = 1; - } else { - ath_print(common, ATH_DBG_FATAL, - "Invalid channel %u MHz\n", freq); - return false; - } - - channelSel = (channelSel << 2) & 0xff; - channelSel = ath9k_hw_reverse_bits(channelSel, 8); - - txctl = REG_READ(ah, AR_PHY_CCK_TX_CTRL); - if (freq == 2484) { - - REG_WRITE(ah, AR_PHY_CCK_TX_CTRL, - txctl | AR_PHY_CCK_TX_CTRL_JAPAN); - } else { - REG_WRITE(ah, AR_PHY_CCK_TX_CTRL, - txctl & ~AR_PHY_CCK_TX_CTRL_JAPAN); - } - - } else if ((freq % 20) == 0 && freq >= 5120) { - channelSel = - ath9k_hw_reverse_bits(((freq - 4800) / 20 << 2), 8); - aModeRefSel = ath9k_hw_reverse_bits(1, 2); - } else if ((freq % 10) == 0) { - channelSel = - ath9k_hw_reverse_bits(((freq - 4800) / 10 << 1), 8); - if (AR_SREV_9100(ah) || AR_SREV_9160_10_OR_LATER(ah)) - aModeRefSel = ath9k_hw_reverse_bits(2, 2); - else - aModeRefSel = ath9k_hw_reverse_bits(1, 2); - } else if ((freq % 5) == 0) { - channelSel = ath9k_hw_reverse_bits((freq - 4800) / 5, 8); - aModeRefSel = ath9k_hw_reverse_bits(1, 2); - } else { - ath_print(common, ATH_DBG_FATAL, - "Invalid channel %u MHz\n", freq); - return false; - } - - reg32 = - (channelSel << 8) | (aModeRefSel << 2) | (bModeSynth << 1) | - (1 << 5) | 0x1; - - REG_WRITE(ah, AR_PHY(0x37), reg32); - - ah->curchan = chan; - ah->curchan_rad_index = -1; - - return true; -} - -void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, - struct ath9k_channel *chan) +/** + * ath9k_hw_ar9280_set_channel - set channel on single-chip device + * @ah: atheros hardware structure + * @chan: + * + * This is the function to change channel on single-chip devices, that is + * all devices after ar9280. + * + * This function takes the channel value in MHz and sets + * hardware channel value. Assumes writes have been enabled to analog bus. + * + * Actual Expression, + * + * For 2GHz channel, + * Channel Frequency = (3/4) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17) + * (freq_ref = 40MHz) + * + * For 5GHz channel, + * Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^10) + * (freq_ref = 40MHz/(24>>amodeRefSel)) + */ +int ath9k_hw_ar9280_set_channel(struct ath_hw *ah, struct ath9k_channel *chan) { u16 bMode, fracMode, aModeRefSel = 0; u32 freq, ndiv, channelSel = 0, channelFrac = 0, reg32 = 0; @@ -111,7 +90,7 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, reg32 = REG_READ(ah, AR_PHY_SYNTH_CONTROL); reg32 &= 0xc0000000; - if (freq < 4800) { + if (freq < 4800) { /* 2 GHz, fractional mode */ u32 txctl; int regWrites = 0; @@ -122,6 +101,7 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, if (AR_SREV_9287_11_OR_LATER(ah)) { if (freq == 2484) { + /* Enable channel spreading for channel 14 */ REG_WRITE_ARRAY(&ah->iniCckfirJapan2484, 1, regWrites); } else { @@ -155,10 +135,15 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, case 1: default: aModeRefSel = 0; + /* + * Enable 2G (fractional) mode for channels + * which are 5MHz spaced. + */ fracMode = 1; refDivA = 1; channelSel = (freq * 0x8000) / 15; + /* RefDivA setting */ REG_RMW_FIELD(ah, AR_AN_SYNTH9, AR_AN_SYNTH9_REFDIVA, refDivA); @@ -180,12 +165,284 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, ah->curchan = chan; ah->curchan_rad_index = -1; + + return 0; +} + +/** + * ath9k_hw_9280_spur_mitigate - convert baseband spur frequency + * @ah: atheros hardware structure + * @chan: + * + * For single-chip solutions. Converts to baseband spur frequency given the + * input channel frequency and compute register settings below. + */ +void ath9k_hw_9280_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan) +{ + int bb_spur = AR_NO_SPUR; + int freq; + int bin, cur_bin; + int bb_spur_off, spur_subchannel_sd; + int spur_freq_sd; + int spur_delta_phase; + int denominator; + int upper, lower, cur_vit_mask; + int tmp, newVal; + int i; + int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8, + AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60 + }; + int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10, + AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60 + }; + int inc[4] = { 0, 100, 0, 0 }; + struct chan_centers centers; + + int8_t mask_m[123]; + int8_t mask_p[123]; + int8_t mask_amt; + int tmp_mask; + int cur_bb_spur; + bool is2GHz = IS_CHAN_2GHZ(chan); + + memset(&mask_m, 0, sizeof(int8_t) * 123); + memset(&mask_p, 0, sizeof(int8_t) * 123); + + ath9k_hw_get_channel_centers(ah, chan, ¢ers); + freq = centers.synth_center; + + ah->config.spurmode = SPUR_ENABLE_EEPROM; + for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) { + cur_bb_spur = ah->eep_ops->get_spur_channel(ah, i, is2GHz); + + if (is2GHz) + cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_2GHZ; + else + cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_5GHZ; + + if (AR_NO_SPUR == cur_bb_spur) + break; + cur_bb_spur = cur_bb_spur - freq; + + if (IS_CHAN_HT40(chan)) { + if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT40) && + (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT40)) { + bb_spur = cur_bb_spur; + break; + } + } else if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT20) && + (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT20)) { + bb_spur = cur_bb_spur; + break; + } + } + + if (AR_NO_SPUR == bb_spur) { + REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, + AR_PHY_FORCE_CLKEN_CCK_MRC_MUX); + return; + } else { + REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, + AR_PHY_FORCE_CLKEN_CCK_MRC_MUX); + } + + bin = bb_spur * 320; + + tmp = REG_READ(ah, AR_PHY_TIMING_CTRL4(0)); + + newVal = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI | + AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER | + AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK | + AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK); + REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0), newVal); + + newVal = (AR_PHY_SPUR_REG_MASK_RATE_CNTL | + AR_PHY_SPUR_REG_ENABLE_MASK_PPM | + AR_PHY_SPUR_REG_MASK_RATE_SELECT | + AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI | + SM(SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH)); + REG_WRITE(ah, AR_PHY_SPUR_REG, newVal); + + if (IS_CHAN_HT40(chan)) { + if (bb_spur < 0) { + spur_subchannel_sd = 1; + bb_spur_off = bb_spur + 10; + } else { + spur_subchannel_sd = 0; + bb_spur_off = bb_spur - 10; + } + } else { + spur_subchannel_sd = 0; + bb_spur_off = bb_spur; + } + + if (IS_CHAN_HT40(chan)) + spur_delta_phase = + ((bb_spur * 262144) / + 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE; + else + spur_delta_phase = + ((bb_spur * 524288) / + 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE; + + denominator = IS_CHAN_2GHZ(chan) ? 44 : 40; + spur_freq_sd = ((bb_spur_off * 2048) / denominator) & 0x3ff; + + newVal = (AR_PHY_TIMING11_USE_SPUR_IN_AGC | + SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) | + SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE)); + REG_WRITE(ah, AR_PHY_TIMING11, newVal); + + newVal = spur_subchannel_sd << AR_PHY_SFCORR_SPUR_SUBCHNL_SD_S; + REG_WRITE(ah, AR_PHY_SFCORR_EXT, newVal); + + cur_bin = -6000; + upper = bin + 100; + lower = bin - 100; + + for (i = 0; i < 4; i++) { + int pilot_mask = 0; + int chan_mask = 0; + int bp = 0; + for (bp = 0; bp < 30; bp++) { + if ((cur_bin > lower) && (cur_bin < upper)) { + pilot_mask = pilot_mask | 0x1 << bp; + chan_mask = chan_mask | 0x1 << bp; + } + cur_bin += 100; + } + cur_bin += inc[i]; + REG_WRITE(ah, pilot_mask_reg[i], pilot_mask); + REG_WRITE(ah, chan_mask_reg[i], chan_mask); + } + + cur_vit_mask = 6100; + upper = bin + 120; + lower = bin - 120; + + for (i = 0; i < 123; i++) { + if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) { + + /* workaround for gcc bug #37014 */ + volatile int tmp_v = abs(cur_vit_mask - bin); + + if (tmp_v < 75) + mask_amt = 1; + else + mask_amt = 0; + if (cur_vit_mask < 0) + mask_m[abs(cur_vit_mask / 100)] = mask_amt; + else + mask_p[cur_vit_mask / 100] = mask_amt; + } + cur_vit_mask -= 100; + } + + tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28) + | (mask_m[48] << 26) | (mask_m[49] << 24) + | (mask_m[50] << 22) | (mask_m[51] << 20) + | (mask_m[52] << 18) | (mask_m[53] << 16) + | (mask_m[54] << 14) | (mask_m[55] << 12) + | (mask_m[56] << 10) | (mask_m[57] << 8) + | (mask_m[58] << 6) | (mask_m[59] << 4) + | (mask_m[60] << 2) | (mask_m[61] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask); + REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask); + + tmp_mask = (mask_m[31] << 28) + | (mask_m[32] << 26) | (mask_m[33] << 24) + | (mask_m[34] << 22) | (mask_m[35] << 20) + | (mask_m[36] << 18) | (mask_m[37] << 16) + | (mask_m[48] << 14) | (mask_m[39] << 12) + | (mask_m[40] << 10) | (mask_m[41] << 8) + | (mask_m[42] << 6) | (mask_m[43] << 4) + | (mask_m[44] << 2) | (mask_m[45] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask); + + tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28) + | (mask_m[18] << 26) | (mask_m[18] << 24) + | (mask_m[20] << 22) | (mask_m[20] << 20) + | (mask_m[22] << 18) | (mask_m[22] << 16) + | (mask_m[24] << 14) | (mask_m[24] << 12) + | (mask_m[25] << 10) | (mask_m[26] << 8) + | (mask_m[27] << 6) | (mask_m[28] << 4) + | (mask_m[29] << 2) | (mask_m[30] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask); + + tmp_mask = (mask_m[0] << 30) | (mask_m[1] << 28) + | (mask_m[2] << 26) | (mask_m[3] << 24) + | (mask_m[4] << 22) | (mask_m[5] << 20) + | (mask_m[6] << 18) | (mask_m[7] << 16) + | (mask_m[8] << 14) | (mask_m[9] << 12) + | (mask_m[10] << 10) | (mask_m[11] << 8) + | (mask_m[12] << 6) | (mask_m[13] << 4) + | (mask_m[14] << 2) | (mask_m[15] << 0); + REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask); + + tmp_mask = (mask_p[15] << 28) + | (mask_p[14] << 26) | (mask_p[13] << 24) + | (mask_p[12] << 22) | (mask_p[11] << 20) + | (mask_p[10] << 18) | (mask_p[9] << 16) + | (mask_p[8] << 14) | (mask_p[7] << 12) + | (mask_p[6] << 10) | (mask_p[5] << 8) + | (mask_p[4] << 6) | (mask_p[3] << 4) + | (mask_p[2] << 2) | (mask_p[1] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask); + + tmp_mask = (mask_p[30] << 28) + | (mask_p[29] << 26) | (mask_p[28] << 24) + | (mask_p[27] << 22) | (mask_p[26] << 20) + | (mask_p[25] << 18) | (mask_p[24] << 16) + | (mask_p[23] << 14) | (mask_p[22] << 12) + | (mask_p[21] << 10) | (mask_p[20] << 8) + | (mask_p[19] << 6) | (mask_p[18] << 4) + | (mask_p[17] << 2) | (mask_p[16] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask); + + tmp_mask = (mask_p[45] << 28) + | (mask_p[44] << 26) | (mask_p[43] << 24) + | (mask_p[42] << 22) | (mask_p[41] << 20) + | (mask_p[40] << 18) | (mask_p[39] << 16) + | (mask_p[38] << 14) | (mask_p[37] << 12) + | (mask_p[36] << 10) | (mask_p[35] << 8) + | (mask_p[34] << 6) | (mask_p[33] << 4) + | (mask_p[32] << 2) | (mask_p[31] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask); + + tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28) + | (mask_p[59] << 26) | (mask_p[58] << 24) + | (mask_p[57] << 22) | (mask_p[56] << 20) + | (mask_p[55] << 18) | (mask_p[54] << 16) + | (mask_p[53] << 14) | (mask_p[52] << 12) + | (mask_p[51] << 10) | (mask_p[50] << 8) + | (mask_p[49] << 6) | (mask_p[48] << 4) + | (mask_p[47] << 2) | (mask_p[46] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask); } -static void -ath9k_phy_modify_rx_buffer(u32 *rfBuf, u32 reg32, - u32 numBits, u32 firstBit, - u32 column) +/* All code below is for non single-chip solutions */ + +/** + * ath9k_phy_modify_rx_buffer() - perform analog swizzling of parameters + * @rfbuf: + * @reg32: + * @numBits: + * @firstBit: + * @column: + * + * Performs analog "swizzling" of parameters into their location. + * Used on external AR2133/AR5133 radios. + */ +static void ath9k_phy_modify_rx_buffer(u32 *rfBuf, u32 reg32, + u32 numBits, u32 firstBit, + u32 column) { u32 tmp32, mask, arrayEntry, lastBit; int32_t bitPosition, bitsLeft; @@ -209,26 +466,556 @@ ath9k_phy_modify_rx_buffer(u32 *rfBuf, u32 reg32, } } -bool -ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, - u16 modesIndex) +/* + * Fix on 2.4 GHz band for orientation sensitivity issue by increasing + * rf_pwd_icsyndiv. + * + * Theoretical Rules: + * if 2 GHz band + * if forceBiasAuto + * if synth_freq < 2412 + * bias = 0 + * else if 2412 <= synth_freq <= 2422 + * bias = 1 + * else // synth_freq > 2422 + * bias = 2 + * else if forceBias > 0 + * bias = forceBias & 7 + * else + * no change, use value from ini file + * else + * no change, invalid band + * + * 1st Mod: + * 2422 also uses value of 2 + * <approved> + * + * 2nd Mod: + * Less than 2412 uses value of 0, 2412 and above uses value of 2 + */ +static void ath9k_hw_force_bias(struct ath_hw *ah, u16 synth_freq) +{ + struct ath_common *common = ath9k_hw_common(ah); + u32 tmp_reg; + int reg_writes = 0; + u32 new_bias = 0; + + if (!AR_SREV_5416(ah) || synth_freq >= 3000) { + return; + } + + BUG_ON(AR_SREV_9280_10_OR_LATER(ah)); + + if (synth_freq < 2412) + new_bias = 0; + else if (synth_freq < 2422) + new_bias = 1; + else + new_bias = 2; + + /* pre-reverse this field */ + tmp_reg = ath9k_hw_reverse_bits(new_bias, 3); + + ath_print(common, ATH_DBG_CONFIG, + "Force rf_pwd_icsyndiv to %1d on %4d\n", + new_bias, synth_freq); + + /* swizzle rf_pwd_icsyndiv */ + ath9k_phy_modify_rx_buffer(ah->analogBank6Data, tmp_reg, 3, 181, 3); + + /* write Bank 6 with new params */ + REG_WRITE_RF_ARRAY(&ah->iniBank6, ah->analogBank6Data, reg_writes); +} + +/** + * ath9k_hw_decrease_chain_power() + * + * @ah: atheros hardware structure + * @chan: + * + * Only used on the AR5416 and AR5418 with the external AR2133/AR5133 radios. + * + * Sets a chain internal RF path to the lowest output power. Any + * further writes to bank6 after this setting will override these + * changes. Thus this function must be the last function in the + * sequence to modify bank 6. + * + * This function must be called after ar5416SetRfRegs() which is + * called from ath9k_hw_process_ini() due to swizzling of bank 6. + * Depends on ah->analogBank6Data being initialized by + * ath9k_hw_set_rf_regs() + * + * Additional additive reduction in power - + * change chain's switch table so chain's tx state is actually the rx + * state value. May produce different results in 2GHz/5GHz as well as + * board to board but in general should be a reduction. + * + * Activated by #ifdef ALTER_SWITCH. Not tried yet. If so, must be + * called after ah->eep_ops->set_board_values() due to RMW of + * PHY_SWITCH_CHAIN_0. + */ +void ath9k_hw_decrease_chain_power(struct ath_hw *ah, + struct ath9k_channel *chan) +{ + int i, regWrites = 0; + u32 bank6SelMask; + u32 *bank6Temp = ah->bank6Temp; + + BUG_ON(AR_SREV_9280_10_OR_LATER(ah)); + + switch (ah->config.diversity_control) { + case ATH9K_ANT_FIXED_A: + bank6SelMask = + (ah->config.antenna_switch_swap & ANTSWAP_AB) ? + REDUCE_CHAIN_0 : /* swapped, reduce chain 0 */ + REDUCE_CHAIN_1; /* normal, select chain 1/2 to reduce */ + break; + case ATH9K_ANT_FIXED_B: + bank6SelMask = + (ah->config.antenna_switch_swap & ANTSWAP_AB) ? + REDUCE_CHAIN_1 : /* swapped, reduce chain 1/2 */ + REDUCE_CHAIN_0; /* normal, select chain 0 to reduce */ + break; + case ATH9K_ANT_VARIABLE: + return; /* do not change anything */ + break; + default: + return; /* do not change anything */ + break; + } + + for (i = 0; i < ah->iniBank6.ia_rows; i++) + bank6Temp[i] = ah->analogBank6Data[i]; + + /* Write Bank 5 to switch Bank 6 write to selected chain only */ + REG_WRITE(ah, AR_PHY_BASE + 0xD8, bank6SelMask); + + /* + * Modify Bank6 selected chain to use lowest amplification. + * Modifies the parameters to a value of 1. + * Depends on existing bank 6 values to be cached in + * ah->analogBank6Data + */ + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 189, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 190, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 191, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 192, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 193, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 222, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 245, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 246, 0); + ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 247, 0); + + REG_WRITE_RF_ARRAY(&ah->iniBank6, bank6Temp, regWrites); + + REG_WRITE(ah, AR_PHY_BASE + 0xD8, 0x00000053); +#ifdef ALTER_SWITCH + REG_WRITE(ah, PHY_SWITCH_CHAIN_0, + (REG_READ(ah, PHY_SWITCH_CHAIN_0) & ~0x38) + | ((REG_READ(ah, PHY_SWITCH_CHAIN_0) >> 3) & 0x38)); +#endif +} + +/** + * ath9k_hw_set_channel - tune to a channel on the external AR2133/AR5133 radios + * @ah: atheros hardware stucture + * @chan: + * + * For the external AR2133/AR5133 radios, takes the MHz channel value and set + * the channel value. Assumes writes enabled to analog bus and bank6 register + * cache in ah->analogBank6Data. + */ +int ath9k_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan) +{ + struct ath_common *common = ath9k_hw_common(ah); + u32 channelSel = 0; + u32 bModeSynth = 0; + u32 aModeRefSel = 0; + u32 reg32 = 0; + u16 freq; + struct chan_centers centers; + + ath9k_hw_get_channel_centers(ah, chan, ¢ers); + freq = centers.synth_center; + + if (freq < 4800) { + u32 txctl; + + if (((freq - 2192) % 5) == 0) { + channelSel = ((freq - 672) * 2 - 3040) / 10; + bModeSynth = 0; + } else if (((freq - 2224) % 5) == 0) { + channelSel = ((freq - 704) * 2 - 3040) / 10; + bModeSynth = 1; + } else { + ath_print(common, ATH_DBG_FATAL, + "Invalid channel %u MHz\n", freq); + return -EINVAL; + } + + channelSel = (channelSel << 2) & 0xff; + channelSel = ath9k_hw_reverse_bits(channelSel, 8); + + txctl = REG_READ(ah, AR_PHY_CCK_TX_CTRL); + if (freq == 2484) { + + REG_WRITE(ah, AR_PHY_CCK_TX_CTRL, + txctl | AR_PHY_CCK_TX_CTRL_JAPAN); + } else { + REG_WRITE(ah, AR_PHY_CCK_TX_CTRL, + txctl & ~AR_PHY_CCK_TX_CTRL_JAPAN); + } + + } else if ((freq % 20) == 0 && freq >= 5120) { + channelSel = + ath9k_hw_reverse_bits(((freq - 4800) / 20 << 2), 8); + aModeRefSel = ath9k_hw_reverse_bits(1, 2); + } else if ((freq % 10) == 0) { + channelSel = + ath9k_hw_reverse_bits(((freq - 4800) / 10 << 1), 8); + if (AR_SREV_9100(ah) || AR_SREV_9160_10_OR_LATER(ah)) + aModeRefSel = ath9k_hw_reverse_bits(2, 2); + else + aModeRefSel = ath9k_hw_reverse_bits(1, 2); + } else if ((freq % 5) == 0) { + channelSel = ath9k_hw_reverse_bits((freq - 4800) / 5, 8); + aModeRefSel = ath9k_hw_reverse_bits(1, 2); + } else { + ath_print(common, ATH_DBG_FATAL, + "Invalid channel %u MHz\n", freq); + return -EINVAL; + } + + ath9k_hw_force_bias(ah, freq); + ath9k_hw_decrease_chain_power(ah, chan); + + reg32 = + (channelSel << 8) | (aModeRefSel << 2) | (bModeSynth << 1) | + (1 << 5) | 0x1; + + REG_WRITE(ah, AR_PHY(0x37), reg32); + + ah->curchan = chan; + ah->curchan_rad_index = -1; + + return 0; +} + +/** + * ath9k_hw_spur_mitigate - convert baseband spur frequency for external radios + * @ah: atheros hardware structure + * @chan: + * + * For non single-chip solutions. Converts to baseband spur frequency given the + * input channel frequency and compute register settings below. + */ +void ath9k_hw_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan) +{ + int bb_spur = AR_NO_SPUR; + int bin, cur_bin; + int spur_freq_sd; + int spur_delta_phase; + int denominator; + int upper, lower, cur_vit_mask; + int tmp, new; + int i; + int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8, + AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60 + }; + int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10, + AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60 + }; + int inc[4] = { 0, 100, 0, 0 }; + + int8_t mask_m[123]; + int8_t mask_p[123]; + int8_t mask_amt; + int tmp_mask; + int cur_bb_spur; + bool is2GHz = IS_CHAN_2GHZ(chan); + + memset(&mask_m, 0, sizeof(int8_t) * 123); + memset(&mask_p, 0, sizeof(int8_t) * 123); + + for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) { + cur_bb_spur = ah->eep_ops->get_spur_channel(ah, i, is2GHz); + if (AR_NO_SPUR == cur_bb_spur) + break; + cur_bb_spur = cur_bb_spur - (chan->channel * 10); + if ((cur_bb_spur > -95) && (cur_bb_spur < 95)) { + bb_spur = cur_bb_spur; + break; + } + } + + if (AR_NO_SPUR == bb_spur) + return; + + bin = bb_spur * 32; + + tmp = REG_READ(ah, AR_PHY_TIMING_CTRL4(0)); + new = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI | + AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER | + AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK | + AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK); + + REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0), new); + + new = (AR_PHY_SPUR_REG_MASK_RATE_CNTL | + AR_PHY_SPUR_REG_ENABLE_MASK_PPM | + AR_PHY_SPUR_REG_MASK_RATE_SELECT | + AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI | + SM(SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH)); + REG_WRITE(ah, AR_PHY_SPUR_REG, new); + + spur_delta_phase = ((bb_spur * 524288) / 100) & + AR_PHY_TIMING11_SPUR_DELTA_PHASE; + + denominator = IS_CHAN_2GHZ(chan) ? 440 : 400; + spur_freq_sd = ((bb_spur * 2048) / denominator) & 0x3ff; + + new = (AR_PHY_TIMING11_USE_SPUR_IN_AGC | + SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) | + SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE)); + REG_WRITE(ah, AR_PHY_TIMING11, new); + + cur_bin = -6000; + upper = bin + 100; + lower = bin - 100; + + for (i = 0; i < 4; i++) { + int pilot_mask = 0; + int chan_mask = 0; + int bp = 0; + for (bp = 0; bp < 30; bp++) { + if ((cur_bin > lower) && (cur_bin < upper)) { + pilot_mask = pilot_mask | 0x1 << bp; + chan_mask = chan_mask | 0x1 << bp; + } + cur_bin += 100; + } + cur_bin += inc[i]; + REG_WRITE(ah, pilot_mask_reg[i], pilot_mask); + REG_WRITE(ah, chan_mask_reg[i], chan_mask); + } + + cur_vit_mask = 6100; + upper = bin + 120; + lower = bin - 120; + + for (i = 0; i < 123; i++) { + if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) { + + /* workaround for gcc bug #37014 */ + volatile int tmp_v = abs(cur_vit_mask - bin); + + if (tmp_v < 75) + mask_amt = 1; + else + mask_amt = 0; + if (cur_vit_mask < 0) + mask_m[abs(cur_vit_mask / 100)] = mask_amt; + else + mask_p[cur_vit_mask / 100] = mask_amt; + } + cur_vit_mask -= 100; + } + + tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28) + | (mask_m[48] << 26) | (mask_m[49] << 24) + | (mask_m[50] << 22) | (mask_m[51] << 20) + | (mask_m[52] << 18) | (mask_m[53] << 16) + | (mask_m[54] << 14) | (mask_m[55] << 12) + | (mask_m[56] << 10) | (mask_m[57] << 8) + | (mask_m[58] << 6) | (mask_m[59] << 4) + | (mask_m[60] << 2) | (mask_m[61] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask); + REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask); + + tmp_mask = (mask_m[31] << 28) + | (mask_m[32] << 26) | (mask_m[33] << 24) + | (mask_m[34] << 22) | (mask_m[35] << 20) + | (mask_m[36] << 18) | (mask_m[37] << 16) + | (mask_m[48] << 14) | (mask_m[39] << 12) + | (mask_m[40] << 10) | (mask_m[41] << 8) + | (mask_m[42] << 6) | (mask_m[43] << 4) + | (mask_m[44] << 2) | (mask_m[45] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask); + + tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28) + | (mask_m[18] << 26) | (mask_m[18] << 24) + | (mask_m[20] << 22) | (mask_m[20] << 20) + | (mask_m[22] << 18) | (mask_m[22] << 16) + | (mask_m[24] << 14) | (mask_m[24] << 12) + | (mask_m[25] << 10) | (mask_m[26] << 8) + | (mask_m[27] << 6) | (mask_m[28] << 4) + | (mask_m[29] << 2) | (mask_m[30] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask); + + tmp_mask = (mask_m[0] << 30) | (mask_m[1] << 28) + | (mask_m[2] << 26) | (mask_m[3] << 24) + | (mask_m[4] << 22) | (mask_m[5] << 20) + | (mask_m[6] << 18) | (mask_m[7] << 16) + | (mask_m[8] << 14) | (mask_m[9] << 12) + | (mask_m[10] << 10) | (mask_m[11] << 8) + | (mask_m[12] << 6) | (mask_m[13] << 4) + | (mask_m[14] << 2) | (mask_m[15] << 0); + REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask); + + tmp_mask = (mask_p[15] << 28) + | (mask_p[14] << 26) | (mask_p[13] << 24) + | (mask_p[12] << 22) | (mask_p[11] << 20) + | (mask_p[10] << 18) | (mask_p[9] << 16) + | (mask_p[8] << 14) | (mask_p[7] << 12) + | (mask_p[6] << 10) | (mask_p[5] << 8) + | (mask_p[4] << 6) | (mask_p[3] << 4) + | (mask_p[2] << 2) | (mask_p[1] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask); + + tmp_mask = (mask_p[30] << 28) + | (mask_p[29] << 26) | (mask_p[28] << 24) + | (mask_p[27] << 22) | (mask_p[26] << 20) + | (mask_p[25] << 18) | (mask_p[24] << 16) + | (mask_p[23] << 14) | (mask_p[22] << 12) + | (mask_p[21] << 10) | (mask_p[20] << 8) + | (mask_p[19] << 6) | (mask_p[18] << 4) + | (mask_p[17] << 2) | (mask_p[16] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask); + + tmp_mask = (mask_p[45] << 28) + | (mask_p[44] << 26) | (mask_p[43] << 24) + | (mask_p[42] << 22) | (mask_p[41] << 20) + | (mask_p[40] << 18) | (mask_p[39] << 16) + | (mask_p[38] << 14) | (mask_p[37] << 12) + | (mask_p[36] << 10) | (mask_p[35] << 8) + | (mask_p[34] << 6) | (mask_p[33] << 4) + | (mask_p[32] << 2) | (mask_p[31] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask); + + tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28) + | (mask_p[59] << 26) | (mask_p[58] << 24) + | (mask_p[57] << 22) | (mask_p[56] << 20) + | (mask_p[55] << 18) | (mask_p[54] << 16) + | (mask_p[53] << 14) | (mask_p[52] << 12) + | (mask_p[51] << 10) | (mask_p[50] << 8) + | (mask_p[49] << 6) | (mask_p[48] << 4) + | (mask_p[47] << 2) | (mask_p[46] << 0); + REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask); + REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask); +} + +/** + * ath9k_hw_rf_alloc_ext_banks - allocates banks for external radio programming + * @ah: atheros hardware structure + * + * Only required for older devices with external AR2133/AR5133 radios. + */ +int ath9k_hw_rf_alloc_ext_banks(struct ath_hw *ah) +{ +#define ATH_ALLOC_BANK(bank, size) do { \ + bank = kzalloc((sizeof(u32) * size), GFP_KERNEL); \ + if (!bank) { \ + ath_print(common, ATH_DBG_FATAL, \ + "Cannot allocate RF banks\n"); \ + return -ENOMEM; \ + } \ + } while (0); + + struct ath_common *common = ath9k_hw_common(ah); + + BUG_ON(AR_SREV_9280_10_OR_LATER(ah)); + + ATH_ALLOC_BANK(ah->analogBank0Data, ah->iniBank0.ia_rows); + ATH_ALLOC_BANK(ah->analogBank1Data, ah->iniBank1.ia_rows); + ATH_ALLOC_BANK(ah->analogBank2Data, ah->iniBank2.ia_rows); + ATH_ALLOC_BANK(ah->analogBank3Data, ah->iniBank3.ia_rows); + ATH_ALLOC_BANK(ah->analogBank6Data, ah->iniBank6.ia_rows); + ATH_ALLOC_BANK(ah->analogBank6TPCData, ah->iniBank6TPC.ia_rows); + ATH_ALLOC_BANK(ah->analogBank7Data, ah->iniBank7.ia_rows); + ATH_ALLOC_BANK(ah->addac5416_21, + ah->iniAddac.ia_rows * ah->iniAddac.ia_columns); + ATH_ALLOC_BANK(ah->bank6Temp, ah->iniBank6.ia_rows); + + return 0; +#undef ATH_ALLOC_BANK +} + + +/** + * ath9k_hw_rf_free_ext_banks - Free memory for analog bank scratch buffers + * @ah: atheros hardware struture + * For the external AR2133/AR5133 radios banks. + */ +void +ath9k_hw_rf_free_ext_banks(struct ath_hw *ah) +{ +#define ATH_FREE_BANK(bank) do { \ + kfree(bank); \ + bank = NULL; \ + } while (0); + + BUG_ON(AR_SREV_9280_10_OR_LATER(ah)); + + ATH_FREE_BANK(ah->analogBank0Data); + ATH_FREE_BANK(ah->analogBank1Data); + ATH_FREE_BANK(ah->analogBank2Data); + ATH_FREE_BANK(ah->analogBank3Data); + ATH_FREE_BANK(ah->analogBank6Data); + ATH_FREE_BANK(ah->analogBank6TPCData); + ATH_FREE_BANK(ah->analogBank7Data); + ATH_FREE_BANK(ah->addac5416_21); + ATH_FREE_BANK(ah->bank6Temp); + +#undef ATH_FREE_BANK +} + +/* * + * ath9k_hw_set_rf_regs - programs rf registers based on EEPROM + * @ah: atheros hardware structure + * @chan: + * @modesIndex: + * + * Used for the external AR2133/AR5133 radios. + * + * Reads the EEPROM header info from the device structure and programs + * all rf registers. This routine requires access to the analog + * rf device. This is not required for single-chip devices. + */ +bool ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, + u16 modesIndex) { u32 eepMinorRev; u32 ob5GHz = 0, db5GHz = 0; u32 ob2GHz = 0, db2GHz = 0; int regWrites = 0; + /* + * Software does not need to program bank data + * for single chip devices, that is AR9280 or anything + * after that. + */ if (AR_SREV_9280_10_OR_LATER(ah)) return true; + /* Setup rf parameters */ eepMinorRev = ah->eep_ops->get_eeprom(ah, EEP_MINOR_REV); + /* Setup Bank 0 Write */ RF_BANK_SETUP(ah->analogBank0Data, &ah->iniBank0, 1); + /* Setup Bank 1 Write */ RF_BANK_SETUP(ah->analogBank1Data, &ah->iniBank1, 1); + /* Setup Bank 2 Write */ RF_BANK_SETUP(ah->analogBank2Data, &ah->iniBank2, 1); + /* Setup Bank 6 Write */ RF_BANK_SETUP(ah->analogBank3Data, &ah->iniBank3, modesIndex); { @@ -239,6 +1026,7 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, } } + /* Only the 5 or 2 GHz OB/DB need to be set for a mode */ if (eepMinorRev >= 2) { if (IS_CHAN_2GHZ(chan)) { ob2GHz = ah->eep_ops->get_eeprom(ah, EEP_OB_2); @@ -257,8 +1045,10 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, } } + /* Setup Bank 7 Setup */ RF_BANK_SETUP(ah->analogBank7Data, &ah->iniBank7, 1); + /* Write Analog registers */ REG_WRITE_RF_ARRAY(&ah->iniBank0, ah->analogBank0Data, regWrites); REG_WRITE_RF_ARRAY(&ah->iniBank1, ah->analogBank1Data, @@ -274,139 +1064,3 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, return true; } - -void -ath9k_hw_rf_free(struct ath_hw *ah) -{ -#define ATH_FREE_BANK(bank) do { \ - kfree(bank); \ - bank = NULL; \ - } while (0); - - ATH_FREE_BANK(ah->analogBank0Data); - ATH_FREE_BANK(ah->analogBank1Data); - ATH_FREE_BANK(ah->analogBank2Data); - ATH_FREE_BANK(ah->analogBank3Data); - ATH_FREE_BANK(ah->analogBank6Data); - ATH_FREE_BANK(ah->analogBank6TPCData); - ATH_FREE_BANK(ah->analogBank7Data); - ATH_FREE_BANK(ah->addac5416_21); - ATH_FREE_BANK(ah->bank6Temp); -#undef ATH_FREE_BANK -} - -bool ath9k_hw_init_rf(struct ath_hw *ah, int *status) -{ - struct ath_common *common = ath9k_hw_common(ah); - - if (!AR_SREV_9280_10_OR_LATER(ah)) { - ah->analogBank0Data = - kzalloc((sizeof(u32) * - ah->iniBank0.ia_rows), GFP_KERNEL); - ah->analogBank1Data = - kzalloc((sizeof(u32) * - ah->iniBank1.ia_rows), GFP_KERNEL); - ah->analogBank2Data = - kzalloc((sizeof(u32) * - ah->iniBank2.ia_rows), GFP_KERNEL); - ah->analogBank3Data = - kzalloc((sizeof(u32) * - ah->iniBank3.ia_rows), GFP_KERNEL); - ah->analogBank6Data = - kzalloc((sizeof(u32) * - ah->iniBank6.ia_rows), GFP_KERNEL); - ah->analogBank6TPCData = - kzalloc((sizeof(u32) * - ah->iniBank6TPC.ia_rows), GFP_KERNEL); - ah->analogBank7Data = - kzalloc((sizeof(u32) * - ah->iniBank7.ia_rows), GFP_KERNEL); - - if (ah->analogBank0Data == NULL - || ah->analogBank1Data == NULL - || ah->analogBank2Data == NULL - || ah->analogBank3Data == NULL - || ah->analogBank6Data == NULL - || ah->analogBank6TPCData == NULL - || ah->analogBank7Data == NULL) { - ath_print(common, ATH_DBG_FATAL, - "Cannot allocate RF banks\n"); - *status = -ENOMEM; - return false; - } - - ah->addac5416_21 = - kzalloc((sizeof(u32) * - ah->iniAddac.ia_rows * - ah->iniAddac.ia_columns), GFP_KERNEL); - if (ah->addac5416_21 == NULL) { - ath_print(common, ATH_DBG_FATAL, - "Cannot allocate addac5416_21\n"); - *status = -ENOMEM; - return false; - } - - ah->bank6Temp = - kzalloc((sizeof(u32) * - ah->iniBank6.ia_rows), GFP_KERNEL); - if (ah->bank6Temp == NULL) { - ath_print(common, ATH_DBG_FATAL, - "Cannot allocate bank6Temp\n"); - *status = -ENOMEM; - return false; - } - } - - return true; -} - -void -ath9k_hw_decrease_chain_power(struct ath_hw *ah, struct ath9k_channel *chan) -{ - int i, regWrites = 0; - u32 bank6SelMask; - u32 *bank6Temp = ah->bank6Temp; - - switch (ah->config.diversity_control) { - case ATH9K_ANT_FIXED_A: - bank6SelMask = - (ah->config.antenna_switch_swap & ANTSWAP_AB) ? - REDUCE_CHAIN_0 : REDUCE_CHAIN_1; - break; - case ATH9K_ANT_FIXED_B: - bank6SelMask = - (ah->config.antenna_switch_swap & ANTSWAP_AB) ? - REDUCE_CHAIN_1 : REDUCE_CHAIN_0; - break; - case ATH9K_ANT_VARIABLE: - return; - break; - default: - return; - break; - } - - for (i = 0; i < ah->iniBank6.ia_rows; i++) - bank6Temp[i] = ah->analogBank6Data[i]; - - REG_WRITE(ah, AR_PHY_BASE + 0xD8, bank6SelMask); - - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 189, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 190, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 191, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 192, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 193, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 222, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 245, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 246, 0); - ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 247, 0); - - REG_WRITE_RF_ARRAY(&ah->iniBank6, bank6Temp, regWrites); - - REG_WRITE(ah, AR_PHY_BASE + 0xD8, 0x00000053); -#ifdef ALTER_SWITCH - REG_WRITE(ah, PHY_SWITCH_CHAIN_0, - (REG_READ(ah, PHY_SWITCH_CHAIN_0) & ~0x38) - | ((REG_READ(ah, PHY_SWITCH_CHAIN_0) >> 3) & 0x38)); -#endif -} diff --git a/drivers/net/wireless/ath/ath9k/phy.h b/drivers/net/wireless/ath/ath9k/phy.h index 140fef7..dc145a1 100644 --- a/drivers/net/wireless/ath/ath9k/phy.h +++ b/drivers/net/wireless/ath/ath9k/phy.h @@ -17,20 +17,26 @@ #ifndef PHY_H #define PHY_H -void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, - struct ath9k_channel - *chan); -bool ath9k_hw_set_channel(struct ath_hw *ah, - struct ath9k_channel *chan); -void ath9k_hw_write_regs(struct ath_hw *ah, u32 modesIndex, - u32 freqIndex, int regWrites); +/* Common between single chip and non single-chip solutions */ +void ath9k_hw_write_regs(struct ath_hw *ah, u32 freqIndex, int regWrites); + +/* Single chip radio settings */ +int ath9k_hw_ar9280_set_channel(struct ath_hw *ah, struct ath9k_channel *chan); +void ath9k_hw_9280_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan); + +/* Routines below are for non single-chip solutions */ +int ath9k_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan); +void ath9k_hw_spur_mitigate(struct ath_hw *ah, struct ath9k_channel *chan); + +int ath9k_hw_rf_alloc_ext_banks(struct ath_hw *ah); +void ath9k_hw_rf_free_ext_banks(struct ath_hw *ah); + bool ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, u16 modesIndex); + void ath9k_hw_decrease_chain_power(struct ath_hw *ah, struct ath9k_channel *chan); -bool ath9k_hw_init_rf(struct ath_hw *ah, - int *status); #define AR_PHY_BASE 0x9800 #define AR_PHY(_n) (AR_PHY_BASE + ((_n)<<2)) @@ -186,8 +192,20 @@ bool ath9k_hw_init_rf(struct ath_hw *ah, #define AR_PHY_PLL_CTL_44_2133 0xeb #define AR_PHY_PLL_CTL_40_2133 0xea -#define AR_PHY_SPECTRAL_SCAN 0x9912 -#define AR_PHY_SPECTRAL_SCAN_ENABLE 0x1 +#define AR_PHY_SPECTRAL_SCAN 0x9910 /* AR9280 spectral scan configuration register */ +#define AR_PHY_SPECTRAL_SCAN_ENABLE 0x1 +#define AR_PHY_SPECTRAL_SCAN_ENA 0x00000001 /* Enable spectral scan, reg 68, bit 0 */ +#define AR_PHY_SPECTRAL_SCAN_ENA_S 0 /* Enable spectral scan, reg 68, bit 0 */ +#define AR_PHY_SPECTRAL_SCAN_ACTIVE 0x00000002 /* Activate spectral scan reg 68, bit 1*/ +#define AR_PHY_SPECTRAL_SCAN_ACTIVE_S 1 /* Activate spectral scan reg 68, bit 1*/ +#define AR_PHY_SPECTRAL_SCAN_FFT_PERIOD 0x000000F0 /* Interval for FFT reports, reg 68, bits 4-7*/ +#define AR_PHY_SPECTRAL_SCAN_FFT_PERIOD_S 4 +#define AR_PHY_SPECTRAL_SCAN_PERIOD 0x0000FF00 /* Interval for FFT reports, reg 68, bits 8-15*/ +#define AR_PHY_SPECTRAL_SCAN_PERIOD_S 8 +#define AR_PHY_SPECTRAL_SCAN_COUNT 0x00FF0000 /* Number of reports, reg 68, bits 16-23*/ +#define AR_PHY_SPECTRAL_SCAN_COUNT_S 16 +#define AR_PHY_SPECTRAL_SCAN_SHORT_REPEAT 0x01000000 /* Short repeat, reg 68, bit 24*/ +#define AR_PHY_SPECTRAL_SCAN_SHORT_REPEAT_S 24 /* Short repeat, reg 68, bit 24*/ #define AR_PHY_RX_DELAY 0x9914 #define AR_PHY_SEARCH_START_DELAY 0x9918 diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c index c880a55..355dd18 100644 --- a/drivers/net/wireless/ath/ath9k/recv.c +++ b/drivers/net/wireless/ath/ath9k/recv.c @@ -202,7 +202,8 @@ static int ath_rx_prepare(struct sk_buff *skb, struct ath_desc *ds, } rcu_read_lock(); - sta = ieee80211_find_sta(sc->hw, hdr->addr2); + /* XXX: use ieee80211_find_sta! */ + sta = ieee80211_find_sta_by_hw(sc->hw, hdr->addr2); if (sta) { an = (struct ath_node *) sta->drv_priv; if (ds->ds_rxstat.rs_rssi != ATH9K_RSSI_BAD && diff --git a/drivers/net/wireless/ath/ath9k/reg.h b/drivers/net/wireless/ath/ath9k/reg.h index ceed009..061e12c 100644 --- a/drivers/net/wireless/ath/ath9k/reg.h +++ b/drivers/net/wireless/ath/ath9k/reg.h @@ -1704,4 +1704,7 @@ enum { #define AR_KEYTABLE_MAC0(_n) (AR_KEYTABLE(_n) + 24) #define AR_KEYTABLE_MAC1(_n) (AR_KEYTABLE(_n) + 28) +#define AR9271_CORE_CLOCK 117 /* clock to 117Mhz */ +#define AR9271_TARGET_BAUD_RATE 19200 /* 115200 */ + #endif diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c index 2a4efcb..8e052f4 100644 --- a/drivers/net/wireless/ath/ath9k/xmit.c +++ b/drivers/net/wireless/ath/ath9k/xmit.c @@ -282,7 +282,8 @@ static void ath_tx_complete_aggr(struct ath_softc *sc, struct ath_txq *txq, rcu_read_lock(); - sta = ieee80211_find_sta(sc->hw, hdr->addr1); + /* XXX: use ieee80211_find_sta! */ + sta = ieee80211_find_sta_by_hw(sc->hw, hdr->addr1); if (!sta) { rcu_read_unlock(); return; diff --git a/drivers/net/wireless/b43/Kconfig b/drivers/net/wireless/b43/Kconfig index 54ea61c..64c12e1 100644 --- a/drivers/net/wireless/b43/Kconfig +++ b/drivers/net/wireless/b43/Kconfig @@ -1,6 +1,6 @@ config B43 tristate "Broadcom 43xx wireless support (mac80211 stack)" - depends on SSB_POSSIBLE && MAC80211 && WLAN_80211 && HAS_DMA + depends on SSB_POSSIBLE && MAC80211 && HAS_DMA select SSB select FW_LOADER ---help--- diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h index 65b23f7..fe3bf94 100644 --- a/drivers/net/wireless/b43/b43.h +++ b/drivers/net/wireless/b43/b43.h @@ -26,8 +26,6 @@ # define B43_DEBUG 0 #endif -#define B43_RX_MAX_SSI 60 - /* MMIO offsets */ #define B43_MMIO_DMA0_REASON 0x20 #define B43_MMIO_DMA0_IRQ_MASK 0x24 diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index ed6e96a..c806924 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -3573,7 +3573,7 @@ static int b43_op_config(struct ieee80211_hw *hw, u32 changed) if (conf->channel->hw_value != phy->channel) b43_switch_channel(dev, conf->channel->hw_value); - dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_RADIOTAP); + dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_MONITOR); /* Adjust the desired TX power level. */ if (conf->power_level != 0) { diff --git a/drivers/net/wireless/b43/phy_lp.c b/drivers/net/wireless/b43/phy_lp.c index c6987b1..3e046ec 100644 --- a/drivers/net/wireless/b43/phy_lp.c +++ b/drivers/net/wireless/b43/phy_lp.c @@ -67,6 +67,7 @@ static void b43_lpphy_op_prepare_structs(struct b43_wldev *dev) struct b43_phy_lp *lpphy = phy->lp; memset(lpphy, 0, sizeof(*lpphy)); + lpphy->antenna = B43_ANTENNA_DEFAULT; //TODO } @@ -379,8 +380,6 @@ static void lpphy_save_dig_flt_state(struct b43_wldev *dev) } } -/* lpphy_restore_dig_flt_state is unused but kept as a reference */ -#if 0 static void lpphy_restore_dig_flt_state(struct b43_wldev *dev) { static const u16 addr[] = { @@ -401,7 +400,6 @@ static void lpphy_restore_dig_flt_state(struct b43_wldev *dev) for (i = 0; i < ARRAY_SIZE(addr); i++) b43_phy_write(dev, addr[i], lpphy->dig_flt_state[i]); } -#endif static void lpphy_baseband_rev2plus_init(struct b43_wldev *dev) { @@ -754,11 +752,17 @@ static void lpphy_clear_deaf(struct b43_wldev *dev, bool user) } } +static void lpphy_set_trsw_over(struct b43_wldev *dev, bool tx, bool rx) +{ + u16 trsw = (tx << 1) | rx; + b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFFC, trsw); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x3); +} + static void lpphy_disable_crs(struct b43_wldev *dev, bool user) { lpphy_set_deaf(dev, user); - b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFFC, 0x1); - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x3); + lpphy_set_trsw_over(dev, false, true); b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFFB); b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x4); b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFF7); @@ -793,6 +797,60 @@ static void lpphy_restore_crs(struct b43_wldev *dev, bool user) struct lpphy_tx_gains { u16 gm, pga, pad, dac; }; +static void lpphy_disable_rx_gain_override(struct b43_wldev *dev) +{ + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFFE); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFEF); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFBF); + if (dev->phy.rev >= 2) { + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFEFF); + if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) { + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFBFF); + b43_phy_mask(dev, B43_PHY_OFDM(0xE5), 0xFFF7); + } + } else { + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFDFF); + } +} + +static void lpphy_enable_rx_gain_override(struct b43_wldev *dev) +{ + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x1); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x10); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x40); + if (dev->phy.rev >= 2) { + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x100); + if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) { + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x400); + b43_phy_set(dev, B43_PHY_OFDM(0xE5), 0x8); + } + } else { + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x200); + } +} + +static void lpphy_disable_tx_gain_override(struct b43_wldev *dev) +{ + if (dev->phy.rev < 2) + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFEFF); + else { + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFF7F); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xBFFF); + } + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xFFBF); +} + +static void lpphy_enable_tx_gain_override(struct b43_wldev *dev) +{ + if (dev->phy.rev < 2) + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x100); + else { + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x80); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x4000); + } + b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x40); +} + static struct lpphy_tx_gains lpphy_get_tx_gains(struct b43_wldev *dev) { struct lpphy_tx_gains gains; @@ -822,6 +880,17 @@ static void lpphy_set_dac_gain(struct b43_wldev *dev, u16 dac) b43_phy_maskset(dev, B43_LPPHY_AFE_DAC_CTL, 0xF000, ctl); } +static u16 lpphy_get_pa_gain(struct b43_wldev *dev) +{ + return b43_phy_read(dev, B43_PHY_OFDM(0xFB)) & 0x7F; +} + +static void lpphy_set_pa_gain(struct b43_wldev *dev, u16 gain) +{ + b43_phy_maskset(dev, B43_PHY_OFDM(0xFB), 0xE03F, gain << 6); + b43_phy_maskset(dev, B43_PHY_OFDM(0xFD), 0x80FF, gain << 8); +} + static void lpphy_set_tx_gains(struct b43_wldev *dev, struct lpphy_tx_gains gains) { @@ -832,25 +901,22 @@ static void lpphy_set_tx_gains(struct b43_wldev *dev, b43_phy_maskset(dev, B43_LPPHY_TX_GAIN_CTL_OVERRIDE_VAL, 0xF800, rf_gain); } else { - pa_gain = b43_phy_read(dev, B43_PHY_OFDM(0xFB)) & 0x1FC0; - pa_gain <<= 2; + pa_gain = lpphy_get_pa_gain(dev); b43_phy_write(dev, B43_LPPHY_TX_GAIN_CTL_OVERRIDE_VAL, (gains.pga << 8) | gains.gm); + /* + * SPEC FIXME The spec calls for (pa_gain << 8) here, but that + * conflicts with the spec for set_pa_gain! Vendor driver bug? + */ b43_phy_maskset(dev, B43_PHY_OFDM(0xFB), - 0x8000, gains.pad | pa_gain); + 0x8000, gains.pad | (pa_gain << 6)); b43_phy_write(dev, B43_PHY_OFDM(0xFC), (gains.pga << 8) | gains.gm); b43_phy_maskset(dev, B43_PHY_OFDM(0xFD), - 0x8000, gains.pad | pa_gain); + 0x8000, gains.pad | (pa_gain << 8)); } lpphy_set_dac_gain(dev, gains.dac); - if (dev->phy.rev < 2) { - b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFEFF, 1 << 8); - } else { - b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFF7F, 1 << 7); - b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_2, 0xBFFF, 1 << 14); - } - b43_phy_maskset(dev, B43_LPPHY_AFE_CTL_OVR, 0xFFBF, 1 << 6); + lpphy_enable_tx_gain_override(dev); } static void lpphy_rev0_1_set_rx_gain(struct b43_wldev *dev, u32 gain) @@ -890,41 +956,6 @@ static void lpphy_rev2plus_set_rx_gain(struct b43_wldev *dev, u32 gain) } } -/* lpphy_disable_rx_gain_override is unused but kept as a reference */ -#if 0 -static void lpphy_disable_rx_gain_override(struct b43_wldev *dev) -{ - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFFE); - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFEF); - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFBF); - if (dev->phy.rev >= 2) { - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFEFF); - if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) { - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFBFF); - b43_phy_mask(dev, B43_PHY_OFDM(0xE5), 0xFFF7); - } - } else { - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFDFF); - } -} -#endif - -static void lpphy_enable_rx_gain_override(struct b43_wldev *dev) -{ - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x1); - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x10); - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x40); - if (dev->phy.rev >= 2) { - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x100); - if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) { - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x400); - b43_phy_set(dev, B43_PHY_OFDM(0xE5), 0x8); - } - } else { - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x200); - } -} - static void lpphy_set_rx_gain(struct b43_wldev *dev, u32 gain) { if (dev->phy.rev < 2) @@ -1009,8 +1040,7 @@ static int lpphy_loopback(struct b43_wldev *dev) memset(&iq_est, 0, sizeof(iq_est)); - b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFFC, 0x3); - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x3); + lpphy_set_trsw_over(dev, true, true); b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 1); b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0xFFFE); b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x800); @@ -1132,7 +1162,7 @@ static void lpphy_set_tx_power_control(struct b43_wldev *dev, b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_NNUM, 0x8FFF, ((u16)lpphy->tssi_npt << 16)); //TODO Set "TSSI Transmit Count" variable to total transmitted frame count - //TODO Disable TX gain override + lpphy_disable_tx_gain_override(dev); lpphy->tx_pwr_idx_over = -1; } } @@ -1318,15 +1348,73 @@ static void lpphy_calibrate_rc(struct b43_wldev *dev) } } +static void b43_lpphy_op_set_rx_antenna(struct b43_wldev *dev, int antenna) +{ + if (dev->phy.rev >= 2) + return; // rev2+ doesn't support antenna diversity + + if (B43_WARN_ON(antenna > B43_ANTENNA_AUTO1)) + return; + + b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_ANTDIVHELP); + + b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFFFD, antenna & 0x2); + b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFFFE, antenna & 0x1); + + b43_hf_write(dev, b43_hf_read(dev) | B43_HF_ANTDIVHELP); + + dev->phy.lp->antenna = antenna; +} + +static void lpphy_set_tx_iqcc(struct b43_wldev *dev, u16 a, u16 b) +{ + u16 tmp[2]; + + tmp[0] = a; + tmp[1] = b; + b43_lptab_write_bulk(dev, B43_LPTAB16(0, 80), 2, tmp); +} + static void lpphy_set_tx_power_by_index(struct b43_wldev *dev, u8 index) { struct b43_phy_lp *lpphy = dev->phy.lp; + struct lpphy_tx_gains gains; + u32 iq_comp, tx_gain, coeff, rf_power; lpphy->tx_pwr_idx_over = index; + lpphy_read_tx_pctl_mode_from_hardware(dev); if (lpphy->txpctl_mode != B43_LPPHY_TXPCTL_OFF) lpphy_set_tx_power_control(dev, B43_LPPHY_TXPCTL_SW); - - //TODO + if (dev->phy.rev >= 2) { + iq_comp = b43_lptab_read(dev, B43_LPTAB32(7, index + 320)); + tx_gain = b43_lptab_read(dev, B43_LPTAB32(7, index + 192)); + gains.pad = (tx_gain >> 16) & 0xFF; + gains.gm = tx_gain & 0xFF; + gains.pga = (tx_gain >> 8) & 0xFF; + gains.dac = (iq_comp >> 28) & 0xFF; + lpphy_set_tx_gains(dev, gains); + } else { + iq_comp = b43_lptab_read(dev, B43_LPTAB32(10, index + 320)); + tx_gain = b43_lptab_read(dev, B43_LPTAB32(10, index + 192)); + b43_phy_maskset(dev, B43_LPPHY_TX_GAIN_CTL_OVERRIDE_VAL, + 0xF800, (tx_gain >> 4) & 0x7FFF); + lpphy_set_dac_gain(dev, tx_gain & 0x7); + lpphy_set_pa_gain(dev, (tx_gain >> 24) & 0x7F); + } + lpphy_set_bb_mult(dev, (iq_comp >> 20) & 0xFF); + lpphy_set_tx_iqcc(dev, (iq_comp >> 10) & 0x3FF, iq_comp & 0x3FF); + if (dev->phy.rev >= 2) { + coeff = b43_lptab_read(dev, B43_LPTAB32(7, index + 448)); + } else { + coeff = b43_lptab_read(dev, B43_LPTAB32(10, index + 448)); + } + b43_lptab_write(dev, B43_LPTAB16(0, 85), coeff & 0xFFFF); + if (dev->phy.rev >= 2) { + rf_power = b43_lptab_read(dev, B43_LPTAB32(7, index + 576)); + b43_phy_maskset(dev, B43_LPPHY_RF_PWR_OVERRIDE, 0xFF00, + rf_power & 0xFFFF);//SPEC FIXME mask & set != 0 + } + lpphy_enable_tx_gain_override(dev); } static void lpphy_btcoex_override(struct b43_wldev *dev) @@ -1335,58 +1423,45 @@ static void lpphy_btcoex_override(struct b43_wldev *dev) b43_write16(dev, B43_MMIO_BTCOEX_TXCTL, 0xFF); } -static void lpphy_pr41573_workaround(struct b43_wldev *dev) +static void b43_lpphy_op_software_rfkill(struct b43_wldev *dev, + bool blocked) { - struct b43_phy_lp *lpphy = dev->phy.lp; - u32 *saved_tab; - const unsigned int saved_tab_size = 256; - enum b43_lpphy_txpctl_mode txpctl_mode; - s8 tx_pwr_idx_over; - u16 tssi_npt, tssi_idx; - - saved_tab = kcalloc(saved_tab_size, sizeof(saved_tab[0]), GFP_KERNEL); - if (!saved_tab) { - b43err(dev->wl, "PR41573 failed. Out of memory!\n"); - return; - } - - lpphy_read_tx_pctl_mode_from_hardware(dev); - txpctl_mode = lpphy->txpctl_mode; - tx_pwr_idx_over = lpphy->tx_pwr_idx_over; - tssi_npt = lpphy->tssi_npt; - tssi_idx = lpphy->tssi_idx; - - if (dev->phy.rev < 2) { - b43_lptab_read_bulk(dev, B43_LPTAB32(10, 0x140), - saved_tab_size, saved_tab); + //TODO check MAC control register + if (blocked) { + if (dev->phy.rev >= 2) { + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0x83FF); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x1F00); + b43_phy_mask(dev, B43_LPPHY_AFE_DDFS, 0x80FF); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2_VAL, 0xDFFF); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x0808); + } else { + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xE0FF); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x1F00); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2_VAL, 0xFCFF); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x0018); + } } else { - b43_lptab_read_bulk(dev, B43_LPTAB32(7, 0x140), - saved_tab_size, saved_tab); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xE0FF); + if (dev->phy.rev >= 2) + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xF7F7); + else + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFFE7); } - //TODO - - kfree(saved_tab); } -static void lpphy_calibration(struct b43_wldev *dev) +/* This was previously called lpphy_japan_filter */ +static void lpphy_set_analog_filter(struct b43_wldev *dev, int channel) { struct b43_phy_lp *lpphy = dev->phy.lp; - enum b43_lpphy_txpctl_mode saved_pctl_mode; - - b43_mac_suspend(dev); - - lpphy_btcoex_override(dev); - lpphy_read_tx_pctl_mode_from_hardware(dev); - saved_pctl_mode = lpphy->txpctl_mode; - lpphy_set_tx_power_control(dev, B43_LPPHY_TXPCTL_OFF); - //TODO Perform transmit power table I/Q LO calibration - if ((dev->phy.rev == 0) && (saved_pctl_mode != B43_LPPHY_TXPCTL_OFF)) - lpphy_pr41573_workaround(dev); - //TODO If a full calibration has not been performed on this channel yet, perform PAPD TX-power calibration - lpphy_set_tx_power_control(dev, saved_pctl_mode); - //TODO Perform I/Q calibration with a single control value set + u16 tmp = (channel == 14); //SPEC FIXME check japanwidefilter! - b43_mac_enable(dev); + if (dev->phy.rev < 2) { //SPEC FIXME Isn't this rev0/1-specific? + b43_phy_maskset(dev, B43_LPPHY_LP_PHY_CTL, 0xFCFF, tmp << 9); + if ((dev->phy.rev == 1) && (lpphy->rc_cap)) + lpphy_set_rc_cap(dev); + } else { + b43_radio_write(dev, B2063_TX_BB_SP3, 0x3F); + } } static void lpphy_set_tssi_mux(struct b43_wldev *dev, enum tssi_mux_mode mode) @@ -1495,6 +1570,473 @@ static void lpphy_tx_pctl_init(struct b43_wldev *dev) } } +static void lpphy_pr41573_workaround(struct b43_wldev *dev) +{ + struct b43_phy_lp *lpphy = dev->phy.lp; + u32 *saved_tab; + const unsigned int saved_tab_size = 256; + enum b43_lpphy_txpctl_mode txpctl_mode; + s8 tx_pwr_idx_over; + u16 tssi_npt, tssi_idx; + + saved_tab = kcalloc(saved_tab_size, sizeof(saved_tab[0]), GFP_KERNEL); + if (!saved_tab) { + b43err(dev->wl, "PR41573 failed. Out of memory!\n"); + return; + } + + lpphy_read_tx_pctl_mode_from_hardware(dev); + txpctl_mode = lpphy->txpctl_mode; + tx_pwr_idx_over = lpphy->tx_pwr_idx_over; + tssi_npt = lpphy->tssi_npt; + tssi_idx = lpphy->tssi_idx; + + if (dev->phy.rev < 2) { + b43_lptab_read_bulk(dev, B43_LPTAB32(10, 0x140), + saved_tab_size, saved_tab); + } else { + b43_lptab_read_bulk(dev, B43_LPTAB32(7, 0x140), + saved_tab_size, saved_tab); + } + //FIXME PHY reset + lpphy_table_init(dev); //FIXME is table init needed? + lpphy_baseband_init(dev); + lpphy_tx_pctl_init(dev); + b43_lpphy_op_software_rfkill(dev, false); + lpphy_set_tx_power_control(dev, B43_LPPHY_TXPCTL_OFF); + if (dev->phy.rev < 2) { + b43_lptab_write_bulk(dev, B43_LPTAB32(10, 0x140), + saved_tab_size, saved_tab); + } else { + b43_lptab_write_bulk(dev, B43_LPTAB32(7, 0x140), + saved_tab_size, saved_tab); + } + b43_write16(dev, B43_MMIO_CHANNEL, lpphy->channel); + lpphy->tssi_npt = tssi_npt; + lpphy->tssi_idx = tssi_idx; + lpphy_set_analog_filter(dev, lpphy->channel); + if (tx_pwr_idx_over != -1) + lpphy_set_tx_power_by_index(dev, tx_pwr_idx_over); + if (lpphy->rc_cap) + lpphy_set_rc_cap(dev); + b43_lpphy_op_set_rx_antenna(dev, lpphy->antenna); + lpphy_set_tx_power_control(dev, txpctl_mode); + kfree(saved_tab); +} + +struct lpphy_rx_iq_comp { u8 chan; s8 c1, c0; }; + +static const struct lpphy_rx_iq_comp lpphy_5354_iq_table[] = { + { .chan = 1, .c1 = -66, .c0 = 15, }, + { .chan = 2, .c1 = -66, .c0 = 15, }, + { .chan = 3, .c1 = -66, .c0 = 15, }, + { .chan = 4, .c1 = -66, .c0 = 15, }, + { .chan = 5, .c1 = -66, .c0 = 15, }, + { .chan = 6, .c1 = -66, .c0 = 15, }, + { .chan = 7, .c1 = -66, .c0 = 14, }, + { .chan = 8, .c1 = -66, .c0 = 14, }, + { .chan = 9, .c1 = -66, .c0 = 14, }, + { .chan = 10, .c1 = -66, .c0 = 14, }, + { .chan = 11, .c1 = -66, .c0 = 14, }, + { .chan = 12, .c1 = -66, .c0 = 13, }, + { .chan = 13, .c1 = -66, .c0 = 13, }, + { .chan = 14, .c1 = -66, .c0 = 13, }, +}; + +static const struct lpphy_rx_iq_comp lpphy_rev0_1_iq_table[] = { + { .chan = 1, .c1 = -64, .c0 = 13, }, + { .chan = 2, .c1 = -64, .c0 = 13, }, + { .chan = 3, .c1 = -64, .c0 = 13, }, + { .chan = 4, .c1 = -64, .c0 = 13, }, + { .chan = 5, .c1 = -64, .c0 = 12, }, + { .chan = 6, .c1 = -64, .c0 = 12, }, + { .chan = 7, .c1 = -64, .c0 = 12, }, + { .chan = 8, .c1 = -64, .c0 = 12, }, + { .chan = 9, .c1 = -64, .c0 = 12, }, + { .chan = 10, .c1 = -64, .c0 = 11, }, + { .chan = 11, .c1 = -64, .c0 = 11, }, + { .chan = 12, .c1 = -64, .c0 = 11, }, + { .chan = 13, .c1 = -64, .c0 = 11, }, + { .chan = 14, .c1 = -64, .c0 = 10, }, + { .chan = 34, .c1 = -62, .c0 = 24, }, + { .chan = 38, .c1 = -62, .c0 = 24, }, + { .chan = 42, .c1 = -62, .c0 = 24, }, + { .chan = 46, .c1 = -62, .c0 = 23, }, + { .chan = 36, .c1 = -62, .c0 = 24, }, + { .chan = 40, .c1 = -62, .c0 = 24, }, + { .chan = 44, .c1 = -62, .c0 = 23, }, + { .chan = 48, .c1 = -62, .c0 = 23, }, + { .chan = 52, .c1 = -62, .c0 = 23, }, + { .chan = 56, .c1 = -62, .c0 = 22, }, + { .chan = 60, .c1 = -62, .c0 = 22, }, + { .chan = 64, .c1 = -62, .c0 = 22, }, + { .chan = 100, .c1 = -62, .c0 = 16, }, + { .chan = 104, .c1 = -62, .c0 = 16, }, + { .chan = 108, .c1 = -62, .c0 = 15, }, + { .chan = 112, .c1 = -62, .c0 = 14, }, + { .chan = 116, .c1 = -62, .c0 = 14, }, + { .chan = 120, .c1 = -62, .c0 = 13, }, + { .chan = 124, .c1 = -62, .c0 = 12, }, + { .chan = 128, .c1 = -62, .c0 = 12, }, + { .chan = 132, .c1 = -62, .c0 = 12, }, + { .chan = 136, .c1 = -62, .c0 = 11, }, + { .chan = 140, .c1 = -62, .c0 = 10, }, + { .chan = 149, .c1 = -61, .c0 = 9, }, + { .chan = 153, .c1 = -61, .c0 = 9, }, + { .chan = 157, .c1 = -61, .c0 = 9, }, + { .chan = 161, .c1 = -61, .c0 = 8, }, + { .chan = 165, .c1 = -61, .c0 = 8, }, + { .chan = 184, .c1 = -62, .c0 = 25, }, + { .chan = 188, .c1 = -62, .c0 = 25, }, + { .chan = 192, .c1 = -62, .c0 = 25, }, + { .chan = 196, .c1 = -62, .c0 = 25, }, + { .chan = 200, .c1 = -62, .c0 = 25, }, + { .chan = 204, .c1 = -62, .c0 = 25, }, + { .chan = 208, .c1 = -62, .c0 = 25, }, + { .chan = 212, .c1 = -62, .c0 = 25, }, + { .chan = 216, .c1 = -62, .c0 = 26, }, +}; + +static const struct lpphy_rx_iq_comp lpphy_rev2plus_iq_comp = { + .chan = 0, + .c1 = -64, + .c0 = 0, +}; + +static u8 lpphy_nbits(s32 val) +{ + u32 tmp = abs(val); + u8 nbits = 0; + + while (tmp != 0) { + nbits++; + tmp >>= 1; + } + + return nbits; +} + +static int lpphy_calc_rx_iq_comp(struct b43_wldev *dev, u16 samples) +{ + struct lpphy_iq_est iq_est; + u16 c0, c1; + int prod, ipwr, qpwr, prod_msb, q_msb, tmp1, tmp2, tmp3, tmp4, ret; + + c1 = b43_phy_read(dev, B43_LPPHY_RX_COMP_COEFF_S); + c0 = c1 >> 8; + c1 |= 0xFF; + + b43_phy_maskset(dev, B43_LPPHY_RX_COMP_COEFF_S, 0xFF00, 0x00C0); + b43_phy_mask(dev, B43_LPPHY_RX_COMP_COEFF_S, 0x00FF); + + ret = lpphy_rx_iq_est(dev, samples, 32, &iq_est); + if (!ret) + goto out; + + prod = iq_est.iq_prod; + ipwr = iq_est.i_pwr; + qpwr = iq_est.q_pwr; + + if (ipwr + qpwr < 2) { + ret = 0; + goto out; + } + + prod_msb = lpphy_nbits(prod); + q_msb = lpphy_nbits(qpwr); + tmp1 = prod_msb - 20; + + if (tmp1 >= 0) { + tmp3 = ((prod << (30 - prod_msb)) + (ipwr >> (1 + tmp1))) / + (ipwr >> tmp1); + } else { + tmp3 = ((prod << (30 - prod_msb)) + (ipwr << (-1 - tmp1))) / + (ipwr << -tmp1); + } + + tmp2 = q_msb - 11; + + if (tmp2 >= 0) + tmp4 = (qpwr << (31 - q_msb)) / (ipwr >> tmp2); + else + tmp4 = (qpwr << (31 - q_msb)) / (ipwr << -tmp2); + + tmp4 -= tmp3 * tmp3; + tmp4 = -int_sqrt(tmp4); + + c0 = tmp3 >> 3; + c1 = tmp4 >> 4; + +out: + b43_phy_maskset(dev, B43_LPPHY_RX_COMP_COEFF_S, 0xFF00, c1); + b43_phy_maskset(dev, B43_LPPHY_RX_COMP_COEFF_S, 0x00FF, c0 << 8); + return ret; +} + +/* Complex number using 2 32-bit signed integers */ +typedef struct {s32 i, q;} lpphy_c32; + +static lpphy_c32 lpphy_cordic(int theta) +{ + u32 arctg[] = { 2949120, 1740967, 919879, 466945, 234379, 117304, + 58666, 29335, 14668, 7334, 3667, 1833, 917, 458, + 229, 115, 57, 29, }; + int i, tmp, signx = 1, angle = 0; + lpphy_c32 ret = { .i = 39797, .q = 0, }; + + theta = clamp_t(int, theta, -180, 180); + + if (theta > 90) { + theta -= 180; + signx = -1; + } else if (theta < -90) { + theta += 180; + signx = -1; + } + + for (i = 0; i <= 17; i++) { + if (theta > angle) { + tmp = ret.i - (ret.q >> i); + ret.q += ret.i >> i; + ret.i = tmp; + angle += arctg[i]; + } else { + tmp = ret.i + (ret.q >> i); + ret.q -= ret.i >> i; + ret.i = tmp; + angle -= arctg[i]; + } + } + + ret.i *= signx; + ret.q *= signx; + + return ret; +} + +static void lpphy_run_samples(struct b43_wldev *dev, u16 samples, u16 loops, + u16 wait) +{ + b43_phy_maskset(dev, B43_LPPHY_SMPL_PLAY_BUFFER_CTL, + 0xFFC0, samples - 1); + if (loops != 0xFFFF) + loops--; + b43_phy_maskset(dev, B43_LPPHY_SMPL_PLAY_COUNT, 0xF000, loops); + b43_phy_maskset(dev, B43_LPPHY_SMPL_PLAY_BUFFER_CTL, 0x3F, wait << 6); + b43_phy_set(dev, B43_LPPHY_A_PHY_CTL_ADDR, 0x1); +} + +//SPEC FIXME what does a negative freq mean? +static void lpphy_start_tx_tone(struct b43_wldev *dev, s32 freq, u16 max) +{ + struct b43_phy_lp *lpphy = dev->phy.lp; + u16 buf[64]; + int i, samples = 0, angle = 0, rotation = (9 * freq) / 500; + lpphy_c32 sample; + + lpphy->tx_tone_freq = freq; + + if (freq) { + /* Find i for which abs(freq) integrally divides 20000 * i */ + for (i = 1; samples * abs(freq) != 20000 * i; i++) { + samples = (20000 * i) / abs(freq); + if(B43_WARN_ON(samples > 63)) + return; + } + } else { + samples = 2; + } + + for (i = 0; i < samples; i++) { + sample = lpphy_cordic(angle); + angle += rotation; + buf[i] = ((sample.i * max) & 0xFF) << 8; + buf[i] |= (sample.q * max) & 0xFF; + } + + b43_lptab_write_bulk(dev, B43_LPTAB16(5, 0), samples, buf); + + lpphy_run_samples(dev, samples, 0xFFFF, 0); +} + +static void lpphy_stop_tx_tone(struct b43_wldev *dev) +{ + struct b43_phy_lp *lpphy = dev->phy.lp; + int i; + + lpphy->tx_tone_freq = 0; + + b43_phy_mask(dev, B43_LPPHY_SMPL_PLAY_COUNT, 0xF000); + for (i = 0; i < 31; i++) { + if (!(b43_phy_read(dev, B43_LPPHY_A_PHY_CTL_ADDR) & 0x1)) + break; + udelay(100); + } +} + + +static void lpphy_papd_cal(struct b43_wldev *dev, struct lpphy_tx_gains gains, + int mode, bool useindex, u8 index) +{ + //TODO +} + +static void lpphy_papd_cal_txpwr(struct b43_wldev *dev) +{ + struct b43_phy_lp *lpphy = dev->phy.lp; + struct ssb_bus *bus = dev->dev->bus; + struct lpphy_tx_gains gains, oldgains; + int old_txpctl, old_afe_ovr, old_rf, old_bbmult; + + lpphy_read_tx_pctl_mode_from_hardware(dev); + old_txpctl = lpphy->txpctl_mode; + old_afe_ovr = b43_phy_read(dev, B43_LPPHY_AFE_CTL_OVR) & 0x40; + if (old_afe_ovr) + oldgains = lpphy_get_tx_gains(dev); + old_rf = b43_phy_read(dev, B43_LPPHY_RF_PWR_OVERRIDE) & 0xFF; + old_bbmult = lpphy_get_bb_mult(dev); + + lpphy_set_tx_power_control(dev, B43_LPPHY_TXPCTL_OFF); + + if (bus->chip_id == 0x4325 && bus->chip_rev == 0) + lpphy_papd_cal(dev, gains, 0, 1, 30); + else + lpphy_papd_cal(dev, gains, 0, 1, 65); + + if (old_afe_ovr) + lpphy_set_tx_gains(dev, oldgains); + lpphy_set_bb_mult(dev, old_bbmult); + lpphy_set_tx_power_control(dev, old_txpctl); + b43_phy_maskset(dev, B43_LPPHY_RF_PWR_OVERRIDE, 0xFF00, old_rf); +} + +static int lpphy_rx_iq_cal(struct b43_wldev *dev, bool noise, bool tx, + bool rx, bool pa, struct lpphy_tx_gains *gains) +{ + struct b43_phy_lp *lpphy = dev->phy.lp; + struct ssb_bus *bus = dev->dev->bus; + const struct lpphy_rx_iq_comp *iqcomp = NULL; + struct lpphy_tx_gains nogains, oldgains; + u16 tmp; + int i, ret; + + memset(&nogains, 0, sizeof(nogains)); + memset(&oldgains, 0, sizeof(oldgains)); + + if (bus->chip_id == 0x5354) { + for (i = 0; i < ARRAY_SIZE(lpphy_5354_iq_table); i++) { + if (lpphy_5354_iq_table[i].chan == lpphy->channel) { + iqcomp = &lpphy_5354_iq_table[i]; + } + } + } else if (dev->phy.rev >= 2) { + iqcomp = &lpphy_rev2plus_iq_comp; + } else { + for (i = 0; i < ARRAY_SIZE(lpphy_rev0_1_iq_table); i++) { + if (lpphy_rev0_1_iq_table[i].chan == lpphy->channel) { + iqcomp = &lpphy_rev0_1_iq_table[i]; + } + } + } + + if (B43_WARN_ON(!iqcomp)) + return 0; + + b43_phy_maskset(dev, B43_LPPHY_RX_COMP_COEFF_S, 0xFF00, iqcomp->c1); + b43_phy_maskset(dev, B43_LPPHY_RX_COMP_COEFF_S, + 0x00FF, iqcomp->c0 << 8); + + if (noise) { + tx = true; + rx = false; + pa = false; + } + + lpphy_set_trsw_over(dev, tx, rx); + + if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) { + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x8); + b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, + 0xFFF7, pa << 3); + } else { + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x20); + b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, + 0xFFDF, pa << 5); + } + + tmp = b43_phy_read(dev, B43_LPPHY_AFE_CTL_OVR) & 0x40; + + if (noise) + lpphy_set_rx_gain(dev, 0x2D5D); + else { + if (tmp) + oldgains = lpphy_get_tx_gains(dev); + if (!gains) + gains = &nogains; + lpphy_set_tx_gains(dev, *gains); + } + + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xFFFE); + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0xFFFE); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x800); + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0x800); + lpphy_set_deaf(dev, false); + if (noise) + ret = lpphy_calc_rx_iq_comp(dev, 0xFFF0); + else { + lpphy_start_tx_tone(dev, 4000, 100); + ret = lpphy_calc_rx_iq_comp(dev, 0x4000); + lpphy_stop_tx_tone(dev); + } + lpphy_clear_deaf(dev, false); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFFC); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFF7); + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFDF); + if (!noise) { + if (tmp) + lpphy_set_tx_gains(dev, oldgains); + else + lpphy_disable_tx_gain_override(dev); + } + lpphy_disable_rx_gain_override(dev); + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xFFFE); + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0xF7FF); + return ret; +} + +static void lpphy_calibration(struct b43_wldev *dev) +{ + struct b43_phy_lp *lpphy = dev->phy.lp; + enum b43_lpphy_txpctl_mode saved_pctl_mode; + bool full_cal = false; + + if (lpphy->full_calib_chan != lpphy->channel) { + full_cal = true; + lpphy->full_calib_chan = lpphy->channel; + } + + b43_mac_suspend(dev); + + lpphy_btcoex_override(dev); + if (dev->phy.rev >= 2) + lpphy_save_dig_flt_state(dev); + lpphy_read_tx_pctl_mode_from_hardware(dev); + saved_pctl_mode = lpphy->txpctl_mode; + lpphy_set_tx_power_control(dev, B43_LPPHY_TXPCTL_OFF); + //TODO Perform transmit power table I/Q LO calibration + if ((dev->phy.rev == 0) && (saved_pctl_mode != B43_LPPHY_TXPCTL_OFF)) + lpphy_pr41573_workaround(dev); + if ((dev->phy.rev >= 2) && full_cal) { + lpphy_papd_cal_txpwr(dev); + } + lpphy_set_tx_power_control(dev, saved_pctl_mode); + if (dev->phy.rev >= 2) + lpphy_restore_dig_flt_state(dev); + lpphy_rx_iq_cal(dev, true, true, false, false, NULL); + + b43_mac_enable(dev); +} + static u16 b43_lpphy_op_read(struct b43_wldev *dev, u16 reg) { b43_write16(dev, B43_MMIO_PHY_CONTROL, reg); @@ -1539,12 +2081,6 @@ static void b43_lpphy_op_radio_write(struct b43_wldev *dev, u16 reg, u16 value) b43_write16(dev, B43_MMIO_RADIO_DATA_LOW, value); } -static void b43_lpphy_op_software_rfkill(struct b43_wldev *dev, - bool blocked) -{ - //TODO -} - struct b206x_channel { u8 channel; u16 freq; @@ -2010,22 +2546,6 @@ static int lpphy_b2062_tune(struct b43_wldev *dev, return err; } - -/* This was previously called lpphy_japan_filter */ -static void lpphy_set_analog_filter(struct b43_wldev *dev, int channel) -{ - struct b43_phy_lp *lpphy = dev->phy.lp; - u16 tmp = (channel == 14); //SPEC FIXME check japanwidefilter! - - if (dev->phy.rev < 2) { //SPEC FIXME Isn't this rev0/1-specific? - b43_phy_maskset(dev, B43_LPPHY_LP_PHY_CTL, 0xFCFF, tmp << 9); - if ((dev->phy.rev == 1) && (lpphy->rc_cap)) - lpphy_set_rc_cap(dev); - } else { - b43_radio_write(dev, B2063_TX_BB_SP3, 0x3F); - } -} - static void lpphy_b2063_vco_calib(struct b43_wldev *dev) { u16 tmp; @@ -2210,18 +2730,6 @@ static int b43_lpphy_op_init(struct b43_wldev *dev) return 0; } -static void b43_lpphy_op_set_rx_antenna(struct b43_wldev *dev, int antenna) -{ - if (dev->phy.rev >= 2) - return; // rev2+ doesn't support antenna diversity - - if (B43_WARN_ON(antenna > B43_ANTENNA_AUTO1)) - return; - - b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFFFD, antenna & 0x2); - b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFFFE, antenna & 0x1); -} - static void b43_lpphy_op_adjust_txpower(struct b43_wldev *dev) { //TODO @@ -2244,6 +2752,11 @@ void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on) } } +static void b43_lpphy_op_pwork_15sec(struct b43_wldev *dev) +{ + //TODO +} + const struct b43_phy_operations b43_phyops_lp = { .allocate = b43_lpphy_op_allocate, .free = b43_lpphy_op_free, @@ -2261,4 +2774,6 @@ const struct b43_phy_operations b43_phyops_lp = { .set_rx_antenna = b43_lpphy_op_set_rx_antenna, .recalc_txpower = b43_lpphy_op_recalc_txpower, .adjust_txpower = b43_lpphy_op_adjust_txpower, + .pwork_15sec = b43_lpphy_op_pwork_15sec, + .pwork_60sec = lpphy_calibration, }; diff --git a/drivers/net/wireless/b43/phy_lp.h b/drivers/net/wireless/b43/phy_lp.h index c3232c1..62737f7 100644 --- a/drivers/net/wireless/b43/phy_lp.h +++ b/drivers/net/wireless/b43/phy_lp.h @@ -286,6 +286,7 @@ #define B43_LPPHY_TR_LOOKUP_6 B43_PHY_OFDM(0xC8) /* TR Lookup 6 */ #define B43_LPPHY_TR_LOOKUP_7 B43_PHY_OFDM(0xC9) /* TR Lookup 7 */ #define B43_LPPHY_TR_LOOKUP_8 B43_PHY_OFDM(0xCA) /* TR Lookup 8 */ +#define B43_LPPHY_RF_PWR_OVERRIDE B43_PHY_OFDM(0xD3) /* RF power override */ @@ -871,12 +872,12 @@ struct b43_phy_lp { u8 rssi_gs; /* RC cap */ - u8 rc_cap; /* FIXME initial value? */ + u8 rc_cap; /* BX arch */ u8 bx_arch; /* Full calibration channel */ - u8 full_calib_chan; /* FIXME initial value? */ + u8 full_calib_chan; /* Transmit iqlocal best coeffs */ bool tx_iqloc_best_coeffs_valid; @@ -891,6 +892,12 @@ struct b43_phy_lp { /* The channel we are tuned to */ u8 channel; + + /* The active antenna diversity mode */ + int antenna; + + /* Frequency of the active TX tone */ + int tx_tone_freq; }; enum tssi_mux_mode { diff --git a/drivers/net/wireless/b43/xmit.c b/drivers/net/wireless/b43/xmit.c index 7a5e294..eda0652 100644 --- a/drivers/net/wireless/b43/xmit.c +++ b/drivers/net/wireless/b43/xmit.c @@ -621,7 +621,6 @@ void b43_rx(struct b43_wldev *dev, struct sk_buff *skb, const void *_rxhdr) (phystat0 & B43_RX_PHYST0_OFDM), (phystat0 & B43_RX_PHYST0_GAINCTL), (phystat3 & B43_RX_PHYST3_TRSTATE)); - status.qual = (rxhdr->jssi * 100) / B43_RX_MAX_SSI; } if (phystat0 & B43_RX_PHYST0_OFDM) diff --git a/drivers/net/wireless/b43legacy/Kconfig b/drivers/net/wireless/b43legacy/Kconfig index 94a4634..1ffa288 100644 --- a/drivers/net/wireless/b43legacy/Kconfig +++ b/drivers/net/wireless/b43legacy/Kconfig @@ -1,6 +1,6 @@ config B43LEGACY tristate "Broadcom 43xx-legacy wireless support (mac80211 stack)" - depends on SSB_POSSIBLE && MAC80211 && WLAN_80211 && HAS_DMA + depends on SSB_POSSIBLE && MAC80211 && HAS_DMA select SSB select FW_LOADER ---help--- diff --git a/drivers/net/wireless/b43legacy/b43legacy.h b/drivers/net/wireless/b43legacy/b43legacy.h index 038baa8..89fe2f9 100644 --- a/drivers/net/wireless/b43legacy/b43legacy.h +++ b/drivers/net/wireless/b43legacy/b43legacy.h @@ -29,8 +29,6 @@ #define B43legacy_IRQWAIT_MAX_RETRIES 20 -#define B43legacy_RX_MAX_SSI 60 /* best guess at max ssi */ - /* MMIO offsets */ #define B43legacy_MMIO_DMA0_REASON 0x20 #define B43legacy_MMIO_DMA0_IRQ_MASK 0x24 diff --git a/drivers/net/wireless/b43legacy/dma.c b/drivers/net/wireless/b43legacy/dma.c index 8664034..0a86bdf 100644 --- a/drivers/net/wireless/b43legacy/dma.c +++ b/drivers/net/wireless/b43legacy/dma.c @@ -1240,8 +1240,9 @@ struct b43legacy_dmaring *parse_cookie(struct b43legacy_wldev *dev, } static int dma_tx_fragment(struct b43legacy_dmaring *ring, - struct sk_buff *skb) + struct sk_buff **in_skb) { + struct sk_buff *skb = *in_skb; const struct b43legacy_dma_ops *ops = ring->ops; struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); u8 *header; @@ -1305,8 +1306,14 @@ static int dma_tx_fragment(struct b43legacy_dmaring *ring, } memcpy(skb_put(bounce_skb, skb->len), skb->data, skb->len); + memcpy(bounce_skb->cb, skb->cb, sizeof(skb->cb)); + bounce_skb->dev = skb->dev; + skb_set_queue_mapping(bounce_skb, skb_get_queue_mapping(skb)); + info = IEEE80211_SKB_CB(bounce_skb); + dev_kfree_skb_any(skb); skb = bounce_skb; + *in_skb = bounce_skb; meta->skb = skb; meta->dmaaddr = map_descbuffer(ring, skb->data, skb->len, 1); if (b43legacy_dma_mapping_error(ring, meta->dmaaddr, skb->len, 1)) { @@ -1360,8 +1367,10 @@ int b43legacy_dma_tx(struct b43legacy_wldev *dev, struct sk_buff *skb) { struct b43legacy_dmaring *ring; + struct ieee80211_hdr *hdr; int err = 0; unsigned long flags; + struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); ring = priority_to_txring(dev, skb_get_queue_mapping(skb)); spin_lock_irqsave(&ring->lock, flags); @@ -1386,7 +1395,11 @@ int b43legacy_dma_tx(struct b43legacy_wldev *dev, goto out_unlock; } - err = dma_tx_fragment(ring, skb); + /* dma_tx_fragment might reallocate the skb, so invalidate pointers pointing + * into the skb data or cb now. */ + hdr = NULL; + info = NULL; + err = dma_tx_fragment(ring, &skb); if (unlikely(err == -ENOKEY)) { /* Drop this packet, as we don't have the encryption key * anymore and must not transmit it unencrypted. */ diff --git a/drivers/net/wireless/b43legacy/main.c b/drivers/net/wireless/b43legacy/main.c index 0983406..d579bb9 100644 --- a/drivers/net/wireless/b43legacy/main.c +++ b/drivers/net/wireless/b43legacy/main.c @@ -2676,7 +2676,7 @@ static int b43legacy_op_dev_config(struct ieee80211_hw *hw, if (conf->channel->hw_value != phy->channel) b43legacy_radio_selectchannel(dev, conf->channel->hw_value, 0); - dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_RADIOTAP); + dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_MONITOR); /* Adjust the desired TX power level. */ if (conf->power_level != 0) { diff --git a/drivers/net/wireless/b43legacy/xmit.c b/drivers/net/wireless/b43legacy/xmit.c index 103f3c9..9c8882d 100644 --- a/drivers/net/wireless/b43legacy/xmit.c +++ b/drivers/net/wireless/b43legacy/xmit.c @@ -549,7 +549,6 @@ void b43legacy_rx(struct b43legacy_wldev *dev, (phystat0 & B43legacy_RX_PHYST0_GAINCTL), (phystat3 & B43legacy_RX_PHYST3_TRSTATE)); status.noise = dev->stats.link_noise; - status.qual = (jssi * 100) / B43legacy_RX_MAX_SSI; /* change to support A PHY */ if (phystat0 & B43legacy_RX_PHYST0_OFDM) status.rate_idx = b43legacy_plcp_get_bitrate_idx_ofdm(plcp, false); diff --git a/drivers/net/wireless/hostap/Kconfig b/drivers/net/wireless/hostap/Kconfig index 08f1e98..287d827 100644 --- a/drivers/net/wireless/hostap/Kconfig +++ b/drivers/net/wireless/hostap/Kconfig @@ -1,6 +1,5 @@ config HOSTAP tristate "IEEE 802.11 for Host AP (Prism2/2.5/3 and WEP/TKIP/CCMP)" - depends on WLAN_80211 select WIRELESS_EXT select WEXT_SPY select WEXT_PRIV diff --git a/drivers/net/wireless/i82586.h b/drivers/net/wireless/i82586.h deleted file mode 100644 index 5f65b25..0000000 --- a/drivers/net/wireless/i82586.h +++ /dev/null @@ -1,413 +0,0 @@ -/* - * Intel 82586 IEEE 802.3 Ethernet LAN Coprocessor. - * - * See: - * Intel Microcommunications 1991 - * p1-1 to p1-37 - * Intel order No. 231658 - * ISBN 1-55512-119-5 - * - * Unfortunately, the above chapter mentions neither - * the System Configuration Pointer (SCP) nor the - * Intermediate System Configuration Pointer (ISCP), - * so we probably need to look elsewhere for the - * whole story -- some recommend the "Intel LAN - * Components manual" but I have neither a copy - * nor a full reference. But "elsewhere" may be - * in the same publication... - * The description of a later device, the - * "82596CA High-Performance 32-Bit Local Area Network - * Coprocessor", (ibid. p1-38 to p1-109) does mention - * the SCP and ISCP and also has an i82586 compatibility - * mode. Even more useful is "AP-235 An 82586 Data Link - * Driver" (ibid. p1-337 to p1-417). - */ - -#define I82586_MEMZ (64 * 1024) - -#define I82586_SCP_ADDR (I82586_MEMZ - sizeof(scp_t)) - -#define ADDR_LEN 6 -#define I82586NULL 0xFFFF - -#define toff(t,p,f) (unsigned short)((void *)(&((t *)((void *)0 + (p)))->f) - (void *)0) - -/* - * System Configuration Pointer (SCP). - */ -typedef struct scp_t scp_t; -struct scp_t -{ - unsigned short scp_sysbus; /* 82586 bus width: */ -#define SCP_SY_16BBUS (0x0 << 0) /* 16 bits */ -#define SCP_SY_8BBUS (0x1 << 0) /* 8 bits. */ - unsigned short scp_junk[2]; /* Unused */ - unsigned short scp_iscpl; /* lower 16 bits of ISCP_ADDR */ - unsigned short scp_iscph; /* upper 16 bits of ISCP_ADDR */ -}; - -/* - * Intermediate System Configuration Pointer (ISCP). - */ -typedef struct iscp_t iscp_t; -struct iscp_t -{ - unsigned short iscp_busy; /* set by CPU before first CA, */ - /* cleared by 82586 after read. */ - unsigned short iscp_offset; /* offset of SCB */ - unsigned short iscp_basel; /* base of SCB */ - unsigned short iscp_baseh; /* " */ -}; - -/* - * System Control Block (SCB). - * The 82586 writes its status to scb_status and then - * raises an interrupt to alert the CPU. - * The CPU writes a command to scb_command and - * then issues a Channel Attention (CA) to alert the 82586. - */ -typedef struct scb_t scb_t; -struct scb_t -{ - unsigned short scb_status; /* Status of 82586 */ -#define SCB_ST_INT (0xF << 12) /* Some of: */ -#define SCB_ST_CX (0x1 << 15) /* Cmd completed */ -#define SCB_ST_FR (0x1 << 14) /* Frame received */ -#define SCB_ST_CNA (0x1 << 13) /* Cmd unit not active */ -#define SCB_ST_RNR (0x1 << 12) /* Rcv unit not ready */ -#define SCB_ST_JUNK0 (0x1 << 11) /* 0 */ -#define SCB_ST_CUS (0x7 << 8) /* Cmd unit status */ -#define SCB_ST_CUS_IDLE (0 << 8) /* Idle */ -#define SCB_ST_CUS_SUSP (1 << 8) /* Suspended */ -#define SCB_ST_CUS_ACTV (2 << 8) /* Active */ -#define SCB_ST_JUNK1 (0x1 << 7) /* 0 */ -#define SCB_ST_RUS (0x7 << 4) /* Rcv unit status */ -#define SCB_ST_RUS_IDLE (0 << 4) /* Idle */ -#define SCB_ST_RUS_SUSP (1 << 4) /* Suspended */ -#define SCB_ST_RUS_NRES (2 << 4) /* No resources */ -#define SCB_ST_RUS_RDY (4 << 4) /* Ready */ - unsigned short scb_command; /* Next command */ -#define SCB_CMD_ACK_CX (0x1 << 15) /* Ack cmd completion */ -#define SCB_CMD_ACK_FR (0x1 << 14) /* Ack frame received */ -#define SCB_CMD_ACK_CNA (0x1 << 13) /* Ack CU not active */ -#define SCB_CMD_ACK_RNR (0x1 << 12) /* Ack RU not ready */ -#define SCB_CMD_JUNKX (0x1 << 11) /* Unused */ -#define SCB_CMD_CUC (0x7 << 8) /* Command Unit command */ -#define SCB_CMD_CUC_NOP (0 << 8) /* Nop */ -#define SCB_CMD_CUC_GO (1 << 8) /* Start cbl_offset */ -#define SCB_CMD_CUC_RES (2 << 8) /* Resume execution */ -#define SCB_CMD_CUC_SUS (3 << 8) /* Suspend " */ -#define SCB_CMD_CUC_ABT (4 << 8) /* Abort " */ -#define SCB_CMD_RESET (0x1 << 7) /* Reset chip (hardware) */ -#define SCB_CMD_RUC (0x7 << 4) /* Receive Unit command */ -#define SCB_CMD_RUC_NOP (0 << 4) /* Nop */ -#define SCB_CMD_RUC_GO (1 << 4) /* Start rfa_offset */ -#define SCB_CMD_RUC_RES (2 << 4) /* Resume reception */ -#define SCB_CMD_RUC_SUS (3 << 4) /* Suspend " */ -#define SCB_CMD_RUC_ABT (4 << 4) /* Abort " */ - unsigned short scb_cbl_offset; /* Offset of first command unit */ - /* Action Command */ - unsigned short scb_rfa_offset; /* Offset of first Receive */ - /* Frame Descriptor in the */ - /* Receive Frame Area */ - unsigned short scb_crcerrs; /* Properly aligned frames */ - /* received with a CRC error */ - unsigned short scb_alnerrs; /* Misaligned frames received */ - /* with a CRC error */ - unsigned short scb_rscerrs; /* Frames lost due to no space */ - unsigned short scb_ovrnerrs; /* Frames lost due to slow bus */ -}; - -#define scboff(p,f) toff(scb_t, p, f) - -/* - * The eight Action Commands. - */ -typedef enum acmd_e acmd_e; -enum acmd_e -{ - acmd_nop = 0, /* Do nothing */ - acmd_ia_setup = 1, /* Load an (ethernet) address into the */ - /* 82586 */ - acmd_configure = 2, /* Update the 82586 operating parameters */ - acmd_mc_setup = 3, /* Load a list of (ethernet) multicast */ - /* addresses into the 82586 */ - acmd_transmit = 4, /* Transmit a frame */ - acmd_tdr = 5, /* Perform a Time Domain Reflectometer */ - /* test on the serial link */ - acmd_dump = 6, /* Copy 82586 registers to memory */ - acmd_diagnose = 7, /* Run an internal self test */ -}; - -/* - * Generic Action Command header. - */ -typedef struct ach_t ach_t; -struct ach_t -{ - unsigned short ac_status; /* Command status: */ -#define AC_SFLD_C (0x1 << 15) /* Command completed */ -#define AC_SFLD_B (0x1 << 14) /* Busy executing */ -#define AC_SFLD_OK (0x1 << 13) /* Completed error free */ -#define AC_SFLD_A (0x1 << 12) /* Command aborted */ -#define AC_SFLD_FAIL (0x1 << 11) /* Selftest failed */ -#define AC_SFLD_S10 (0x1 << 10) /* No carrier sense */ - /* during transmission */ -#define AC_SFLD_S9 (0x1 << 9) /* Tx unsuccessful: */ - /* (stopped) lost CTS */ -#define AC_SFLD_S8 (0x1 << 8) /* Tx unsuccessful: */ - /* (stopped) slow DMA */ -#define AC_SFLD_S7 (0x1 << 7) /* Tx deferred: */ - /* other link traffic */ -#define AC_SFLD_S6 (0x1 << 6) /* Heart Beat: collision */ - /* detect after last tx */ -#define AC_SFLD_S5 (0x1 << 5) /* Tx stopped: */ - /* excessive collisions */ -#define AC_SFLD_MAXCOL (0xF << 0) /* Collision count */ - unsigned short ac_command; /* Command specifier: */ -#define AC_CFLD_EL (0x1 << 15) /* End of command list */ -#define AC_CFLD_S (0x1 << 14) /* Suspend on completion */ -#define AC_CFLD_I (0x1 << 13) /* Interrupt on completion */ -#define AC_CFLD_CMD (0x7 << 0) /* acmd_e */ - unsigned short ac_link; /* Next Action Command */ -}; - -#define acoff(p,f) toff(ach_t, p, f) - -/* - * The Nop Action Command. - */ -typedef struct ac_nop_t ac_nop_t; -struct ac_nop_t -{ - ach_t nop_h; -}; - -/* - * The IA-Setup Action Command. - */ -typedef struct ac_ias_t ac_ias_t; -struct ac_ias_t -{ - ach_t ias_h; - unsigned char ias_addr[ADDR_LEN]; /* The (ethernet) address */ -}; - -/* - * The Configure Action Command. - */ -typedef struct ac_cfg_t ac_cfg_t; -struct ac_cfg_t -{ - ach_t cfg_h; - unsigned char cfg_byte_cnt; /* Size foll data: 4-12 */ -#define AC_CFG_BYTE_CNT(v) (((v) & 0xF) << 0) - unsigned char cfg_fifolim; /* FIFO threshold */ -#define AC_CFG_FIFOLIM(v) (((v) & 0xF) << 0) - unsigned char cfg_byte8; -#define AC_CFG_SAV_BF(v) (((v) & 0x1) << 7) /* Save rxd bad frames */ -#define AC_CFG_SRDY(v) (((v) & 0x1) << 6) /* SRDY/ARDY pin means */ - /* external sync. */ - unsigned char cfg_byte9; -#define AC_CFG_ELPBCK(v) (((v) & 0x1) << 7) /* External loopback */ -#define AC_CFG_ILPBCK(v) (((v) & 0x1) << 6) /* Internal loopback */ -#define AC_CFG_PRELEN(v) (((v) & 0x3) << 4) /* Preamble length */ -#define AC_CFG_PLEN_2 0 /* 2 bytes */ -#define AC_CFG_PLEN_4 1 /* 4 bytes */ -#define AC_CFG_PLEN_8 2 /* 8 bytes */ -#define AC_CFG_PLEN_16 3 /* 16 bytes */ -#define AC_CFG_ALOC(v) (((v) & 0x1) << 3) /* Addr/len data is */ - /* explicit in buffers */ -#define AC_CFG_ADDRLEN(v) (((v) & 0x7) << 0) /* Bytes per address */ - unsigned char cfg_byte10; -#define AC_CFG_BOFMET(v) (((v) & 0x1) << 7) /* Use alternate expo. */ - /* backoff method */ -#define AC_CFG_ACR(v) (((v) & 0x7) << 4) /* Accelerated cont. res. */ -#define AC_CFG_LINPRIO(v) (((v) & 0x7) << 0) /* Linear priority */ - unsigned char cfg_ifs; /* Interframe spacing */ - unsigned char cfg_slotl; /* Slot time (low byte) */ - unsigned char cfg_byte13; -#define AC_CFG_RETRYNUM(v) (((v) & 0xF) << 4) /* Max. collision retry */ -#define AC_CFG_SLTTMHI(v) (((v) & 0x7) << 0) /* Slot time (high bits) */ - unsigned char cfg_byte14; -#define AC_CFG_FLGPAD(v) (((v) & 0x1) << 7) /* Pad with HDLC flags */ -#define AC_CFG_BTSTF(v) (((v) & 0x1) << 6) /* Do HDLC bitstuffing */ -#define AC_CFG_CRC16(v) (((v) & 0x1) << 5) /* 16 bit CCITT CRC */ -#define AC_CFG_NCRC(v) (((v) & 0x1) << 4) /* Insert no CRC */ -#define AC_CFG_TNCRS(v) (((v) & 0x1) << 3) /* Tx even if no carrier */ -#define AC_CFG_MANCH(v) (((v) & 0x1) << 2) /* Manchester coding */ -#define AC_CFG_BCDIS(v) (((v) & 0x1) << 1) /* Disable broadcast */ -#define AC_CFG_PRM(v) (((v) & 0x1) << 0) /* Promiscuous mode */ - unsigned char cfg_byte15; -#define AC_CFG_ICDS(v) (((v) & 0x1) << 7) /* Internal collision */ - /* detect source */ -#define AC_CFG_CDTF(v) (((v) & 0x7) << 4) /* Collision detect */ - /* filter in bit times */ -#define AC_CFG_ICSS(v) (((v) & 0x1) << 3) /* Internal carrier */ - /* sense source */ -#define AC_CFG_CSTF(v) (((v) & 0x7) << 0) /* Carrier sense */ - /* filter in bit times */ - unsigned short cfg_min_frm_len; -#define AC_CFG_MNFRM(v) (((v) & 0xFF) << 0) /* Min. bytes/frame (<= 255) */ -}; - -/* - * The MC-Setup Action Command. - */ -typedef struct ac_mcs_t ac_mcs_t; -struct ac_mcs_t -{ - ach_t mcs_h; - unsigned short mcs_cnt; /* No. of bytes of MC addresses */ -#if 0 - unsigned char mcs_data[ADDR_LEN]; /* The first MC address .. */ - ... -#endif -}; - -#define I82586_MAX_MULTICAST_ADDRESSES 128 /* Hardware hashed filter */ - -/* - * The Transmit Action Command. - */ -typedef struct ac_tx_t ac_tx_t; -struct ac_tx_t -{ - ach_t tx_h; - unsigned short tx_tbd_offset; /* Address of list of buffers. */ -#if 0 -Linux packets are passed down with the destination MAC address -and length/type field already prepended to the data, -so we do not need to insert it. Consistent with this -we must also set the AC_CFG_ALOC(..) flag during the -ac_cfg_t action command. - unsigned char tx_addr[ADDR_LEN]; /* The frame dest. address */ - unsigned short tx_length; /* The frame length */ -#endif /* 0 */ -}; - -/* - * The Time Domain Reflectometer Action Command. - */ -typedef struct ac_tdr_t ac_tdr_t; -struct ac_tdr_t -{ - ach_t tdr_h; - unsigned short tdr_result; /* Result. */ -#define AC_TDR_LNK_OK (0x1 << 15) /* No link problem */ -#define AC_TDR_XCVR_PRB (0x1 << 14) /* Txcvr cable problem */ -#define AC_TDR_ET_OPN (0x1 << 13) /* Open on the link */ -#define AC_TDR_ET_SRT (0x1 << 12) /* Short on the link */ -#define AC_TDR_TIME (0x7FF << 0) /* Distance to problem */ - /* site in transmit */ - /* clock cycles */ -}; - -/* - * The Dump Action Command. - */ -typedef struct ac_dmp_t ac_dmp_t; -struct ac_dmp_t -{ - ach_t dmp_h; - unsigned short dmp_offset; /* Result. */ -}; - -/* - * Size of the result of the dump command. - */ -#define DUMPBYTES 170 - -/* - * The Diagnose Action Command. - */ -typedef struct ac_dgn_t ac_dgn_t; -struct ac_dgn_t -{ - ach_t dgn_h; -}; - -/* - * Transmit Buffer Descriptor (TBD). - */ -typedef struct tbd_t tbd_t; -struct tbd_t -{ - unsigned short tbd_status; /* Written by the CPU */ -#define TBD_STATUS_EOF (0x1 << 15) /* This TBD is the */ - /* last for this frame */ -#define TBD_STATUS_ACNT (0x3FFF << 0) /* Actual count of data */ - /* bytes in this buffer */ - unsigned short tbd_next_bd_offset; /* Next in list */ - unsigned short tbd_bufl; /* Buffer address (low) */ - unsigned short tbd_bufh; /* " " (high) */ -}; - -/* - * Receive Buffer Descriptor (RBD). - */ -typedef struct rbd_t rbd_t; -struct rbd_t -{ - unsigned short rbd_status; /* Written by the 82586 */ -#define RBD_STATUS_EOF (0x1 << 15) /* This RBD is the */ - /* last for this frame */ -#define RBD_STATUS_F (0x1 << 14) /* ACNT field is valid */ -#define RBD_STATUS_ACNT (0x3FFF << 0) /* Actual no. of data */ - /* bytes in this buffer */ - unsigned short rbd_next_rbd_offset; /* Next rbd in list */ - unsigned short rbd_bufl; /* Data pointer (low) */ - unsigned short rbd_bufh; /* " " (high) */ - unsigned short rbd_el_size; /* EL+Data buf. size */ -#define RBD_EL (0x1 << 15) /* This BD is the */ - /* last in the list */ -#define RBD_SIZE (0x3FFF << 0) /* No. of bytes the */ - /* buffer can hold */ -}; - -#define rbdoff(p,f) toff(rbd_t, p, f) - -/* - * Frame Descriptor (FD). - */ -typedef struct fd_t fd_t; -struct fd_t -{ - unsigned short fd_status; /* Written by the 82586 */ -#define FD_STATUS_C (0x1 << 15) /* Completed storing frame */ -#define FD_STATUS_B (0x1 << 14) /* FD was consumed by RU */ -#define FD_STATUS_OK (0x1 << 13) /* Frame rxd successfully */ -#define FD_STATUS_S11 (0x1 << 11) /* CRC error */ -#define FD_STATUS_S10 (0x1 << 10) /* Alignment error */ -#define FD_STATUS_S9 (0x1 << 9) /* Ran out of resources */ -#define FD_STATUS_S8 (0x1 << 8) /* Rx DMA overrun */ -#define FD_STATUS_S7 (0x1 << 7) /* Frame too short */ -#define FD_STATUS_S6 (0x1 << 6) /* No EOF flag */ - unsigned short fd_command; /* Command */ -#define FD_COMMAND_EL (0x1 << 15) /* Last FD in list */ -#define FD_COMMAND_S (0x1 << 14) /* Suspend RU after rx */ - unsigned short fd_link_offset; /* Next FD */ - unsigned short fd_rbd_offset; /* First RBD (data) */ - /* Prepared by CPU, */ - /* updated by 82586 */ -#if 0 -I think the rest is unused since we -have set AC_CFG_ALOC(..). However, just -in case, we leave the space. -#endif /* 0 */ - unsigned char fd_dest[ADDR_LEN]; /* Destination address */ - /* Written by 82586 */ - unsigned char fd_src[ADDR_LEN]; /* Source address */ - /* Written by 82586 */ - unsigned short fd_length; /* Frame length or type */ - /* Written by 82586 */ -}; - -#define fdoff(p,f) toff(fd_t, p, f) - -/* - * This software may only be used and distributed - * according to the terms of the GNU General Public License. - * - * For more details, see wavelan.c. - */ diff --git a/drivers/net/wireless/i82593.h b/drivers/net/wireless/i82593.h deleted file mode 100644 index afac5c7..0000000 --- a/drivers/net/wireless/i82593.h +++ /dev/null @@ -1,229 +0,0 @@ -/* - * Definitions for Intel 82593 CSMA/CD Core LAN Controller - * The definitions are taken from the 1992 users manual with Intel - * order number 297125-001. - * - * /usr/src/pc/RCS/i82593.h,v 1.1 1996/07/17 15:23:12 root Exp - * - * Copyright 1994, Anders Klemets <klemets@it.kth.se> - * - * HISTORY - * i82593.h,v - * Revision 1.4 2005/11/4 09:15:00 baroniunas - * Modified copyright with permission of author as follows: - * - * "If I82539.H is the only file with my copyright statement - * that is included in the Source Forge project, then you have - * my approval to change the copyright statement to be a GPL - * license, in the way you proposed on October 10." - * - * Revision 1.1 1996/07/17 15:23:12 root - * Initial revision - * - * Revision 1.3 1995/04/05 15:13:58 adj - * Initial alpha release - * - * Revision 1.2 1994/06/16 23:57:31 klemets - * Mirrored all the fields in the configuration block. - * - * Revision 1.1 1994/06/02 20:25:34 klemets - * Initial revision - * - * - */ -#ifndef _I82593_H -#define _I82593_H - -/* Intel 82593 CSMA/CD Core LAN Controller */ - -/* Port 0 Command Register definitions */ - -/* Execution operations */ -#define OP0_NOP 0 /* CHNL = 0 */ -#define OP0_SWIT_TO_PORT_1 0 /* CHNL = 1 */ -#define OP0_IA_SETUP 1 -#define OP0_CONFIGURE 2 -#define OP0_MC_SETUP 3 -#define OP0_TRANSMIT 4 -#define OP0_TDR 5 -#define OP0_DUMP 6 -#define OP0_DIAGNOSE 7 -#define OP0_TRANSMIT_NO_CRC 9 -#define OP0_RETRANSMIT 12 -#define OP0_ABORT 13 -/* Reception operations */ -#define OP0_RCV_ENABLE 8 -#define OP0_RCV_DISABLE 10 -#define OP0_STOP_RCV 11 -/* Status pointer control operations */ -#define OP0_FIX_PTR 15 /* CHNL = 1 */ -#define OP0_RLS_PTR 15 /* CHNL = 0 */ -#define OP0_RESET 14 - -#define CR0_CHNL (1 << 4) /* 0=Channel 0, 1=Channel 1 */ -#define CR0_STATUS_0 0x00 -#define CR0_STATUS_1 0x20 -#define CR0_STATUS_2 0x40 -#define CR0_STATUS_3 0x60 -#define CR0_INT_ACK (1 << 7) /* 0=No ack, 1=acknowledge */ - -/* Port 0 Status Register definitions */ - -#define SR0_NO_RESULT 0 /* dummy */ -#define SR0_EVENT_MASK 0x0f -#define SR0_IA_SETUP_DONE 1 -#define SR0_CONFIGURE_DONE 2 -#define SR0_MC_SETUP_DONE 3 -#define SR0_TRANSMIT_DONE 4 -#define SR0_TDR_DONE 5 -#define SR0_DUMP_DONE 6 -#define SR0_DIAGNOSE_PASSED 7 -#define SR0_TRANSMIT_NO_CRC_DONE 9 -#define SR0_RETRANSMIT_DONE 12 -#define SR0_EXECUTION_ABORTED 13 -#define SR0_END_OF_FRAME 8 -#define SR0_RECEPTION_ABORTED 10 -#define SR0_DIAGNOSE_FAILED 15 -#define SR0_STOP_REG_HIT 11 - -#define SR0_CHNL (1 << 4) -#define SR0_EXECUTION (1 << 5) -#define SR0_RECEPTION (1 << 6) -#define SR0_INTERRUPT (1 << 7) -#define SR0_BOTH_RX_TX (SR0_EXECUTION | SR0_RECEPTION) - -#define SR3_EXEC_STATE_MASK 0x03 -#define SR3_EXEC_IDLE 0 -#define SR3_TX_ABORT_IN_PROGRESS 1 -#define SR3_EXEC_ACTIVE 2 -#define SR3_ABORT_IN_PROGRESS 3 -#define SR3_EXEC_CHNL (1 << 2) -#define SR3_STP_ON_NO_RSRC (1 << 3) -#define SR3_RCVING_NO_RSRC (1 << 4) -#define SR3_RCV_STATE_MASK 0x60 -#define SR3_RCV_IDLE 0x00 -#define SR3_RCV_READY 0x20 -#define SR3_RCV_ACTIVE 0x40 -#define SR3_RCV_STOP_IN_PROG 0x60 -#define SR3_RCV_CHNL (1 << 7) - -/* Port 1 Command Register definitions */ - -#define OP1_NOP 0 -#define OP1_SWIT_TO_PORT_0 1 -#define OP1_INT_DISABLE 2 -#define OP1_INT_ENABLE 3 -#define OP1_SET_TS 5 -#define OP1_RST_TS 7 -#define OP1_POWER_DOWN 8 -#define OP1_RESET_RING_MNGMT 11 -#define OP1_RESET 14 -#define OP1_SEL_RST 15 - -#define CR1_STATUS_4 0x00 -#define CR1_STATUS_5 0x20 -#define CR1_STATUS_6 0x40 -#define CR1_STOP_REG_UPDATE (1 << 7) - -/* Receive frame status bits */ - -#define RX_RCLD (1 << 0) -#define RX_IA_MATCH (1 << 1) -#define RX_NO_AD_MATCH (1 << 2) -#define RX_NO_SFD (1 << 3) -#define RX_SRT_FRM (1 << 7) -#define RX_OVRRUN (1 << 8) -#define RX_ALG_ERR (1 << 10) -#define RX_CRC_ERR (1 << 11) -#define RX_LEN_ERR (1 << 12) -#define RX_RCV_OK (1 << 13) -#define RX_TYP_LEN (1 << 15) - -/* Transmit status bits */ - -#define TX_NCOL_MASK 0x0f -#define TX_FRTL (1 << 4) -#define TX_MAX_COL (1 << 5) -#define TX_HRT_BEAT (1 << 6) -#define TX_DEFER (1 << 7) -#define TX_UND_RUN (1 << 8) -#define TX_LOST_CTS (1 << 9) -#define TX_LOST_CRS (1 << 10) -#define TX_LTCOL (1 << 11) -#define TX_OK (1 << 13) -#define TX_COLL (1 << 15) - -struct i82593_conf_block { - u_char fifo_limit : 4, - forgnesi : 1, - fifo_32 : 1, - d6mod : 1, - throttle_enb : 1; - u_char throttle : 6, - cntrxint : 1, - contin : 1; - u_char addr_len : 3, - acloc : 1, - preamb_len : 2, - loopback : 2; - u_char lin_prio : 3, - tbofstop : 1, - exp_prio : 3, - bof_met : 1; - u_char : 4, - ifrm_spc : 4; - u_char : 5, - slottim_low : 3; - u_char slottim_hi : 3, - : 1, - max_retr : 4; - u_char prmisc : 1, - bc_dis : 1, - : 1, - crs_1 : 1, - nocrc_ins : 1, - crc_1632 : 1, - : 1, - crs_cdt : 1; - u_char cs_filter : 3, - crs_src : 1, - cd_filter : 3, - : 1; - u_char : 2, - min_fr_len : 6; - u_char lng_typ : 1, - lng_fld : 1, - rxcrc_xf : 1, - artx : 1, - sarec : 1, - tx_jabber : 1, /* why is this called max_len in the manual? */ - hash_1 : 1, - lbpkpol : 1; - u_char : 6, - fdx : 1, - : 1; - u_char dummy_6 : 6, /* supposed to be ones */ - mult_ia : 1, - dis_bof : 1; - u_char dummy_1 : 1, /* supposed to be one */ - tx_ifs_retrig : 2, - mc_all : 1, - rcv_mon : 2, - frag_acpt : 1, - tstrttrs : 1; - u_char fretx : 1, - runt_eop : 1, - hw_sw_pin : 1, - big_endn : 1, - syncrqs : 1, - sttlen : 1, - tx_eop : 1, - rx_eop : 1; - u_char rbuf_size : 5, - rcvstop : 1, - : 2; -}; - -#define I82593_MAX_MULTICAST_ADDRESSES 128 /* Hardware hashed filter */ - -#endif /* _I82593_H */ diff --git a/drivers/net/wireless/ipw2x00/Kconfig b/drivers/net/wireless/ipw2x00/Kconfig index 59ec9ee..2715b10 100644 --- a/drivers/net/wireless/ipw2x00/Kconfig +++ b/drivers/net/wireless/ipw2x00/Kconfig @@ -4,7 +4,7 @@ config IPW2100 tristate "Intel PRO/Wireless 2100 Network Connection" - depends on PCI && WLAN_80211 && CFG80211 + depends on PCI && CFG80211 select WIRELESS_EXT select WEXT_SPY select WEXT_PRIV @@ -65,7 +65,7 @@ config IPW2100_DEBUG config IPW2200 tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection" - depends on PCI && WLAN_80211 && CFG80211 && CFG80211_WEXT + depends on PCI && CFG80211 && CFG80211_WEXT select WIRELESS_EXT select WEXT_SPY select WEXT_PRIV @@ -154,7 +154,7 @@ config IPW2200_DEBUG config LIBIPW tristate - depends on PCI && WLAN_80211 && CFG80211 + depends on PCI && CFG80211 select WIRELESS_EXT select WEXT_SPY select CRYPTO diff --git a/drivers/net/wireless/iwlwifi/Kconfig b/drivers/net/wireless/iwlwifi/Kconfig index c82c97b..b16b06c 100644 --- a/drivers/net/wireless/iwlwifi/Kconfig +++ b/drivers/net/wireless/iwlwifi/Kconfig @@ -1,6 +1,6 @@ config IWLWIFI tristate "Intel Wireless Wifi" - depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL + depends on PCI && MAC80211 && EXPERIMENTAL select FW_LOADER config IWLWIFI_SPECTRUM_MEASUREMENT diff --git a/drivers/net/wireless/iwlwifi/iwl-1000.c b/drivers/net/wireless/iwlwifi/iwl-1000.c index 3a645e4..1e387b9 100644 --- a/drivers/net/wireless/iwlwifi/iwl-1000.c +++ b/drivers/net/wireless/iwlwifi/iwl-1000.c @@ -164,7 +164,7 @@ struct iwl_cfg iwl1000_bgn_cfg = { .valid_tx_ant = ANT_A, .valid_rx_ant = ANT_AB, .pll_cfg_val = CSR50_ANA_PLL_CFG_VAL, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .max_ll_items = OTP_MAX_LL_ITEMS_1000, .shadow_ram_support = false, @@ -190,7 +190,7 @@ struct iwl_cfg iwl1000_bg_cfg = { .valid_tx_ant = ANT_A, .valid_rx_ant = ANT_AB, .pll_cfg_val = CSR50_ANA_PLL_CFG_VAL, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .max_ll_items = OTP_MAX_LL_ITEMS_1000, .shadow_ram_support = false, diff --git a/drivers/net/wireless/iwlwifi/iwl-3945-rs.c b/drivers/net/wireless/iwlwifi/iwl-3945-rs.c index cbb0585..dc81e19 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945-rs.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945-rs.c @@ -42,38 +42,6 @@ #define RS_NAME "iwl-3945-rs" -struct iwl3945_rate_scale_data { - u64 data; - s32 success_counter; - s32 success_ratio; - s32 counter; - s32 average_tpt; - unsigned long stamp; -}; - -struct iwl3945_rs_sta { - spinlock_t lock; - struct iwl_priv *priv; - s32 *expected_tpt; - unsigned long last_partial_flush; - unsigned long last_flush; - u32 flush_time; - u32 last_tx_packets; - u32 tx_packets; - u8 tgg; - u8 flush_pending; - u8 start_rate; - u8 ibss_sta_added; - struct timer_list rate_scale_flush; - struct iwl3945_rate_scale_data win[IWL_RATE_COUNT_3945]; -#ifdef CONFIG_MAC80211_DEBUGFS - struct dentry *rs_sta_dbgfs_stats_table_file; -#endif - - /* used to be in sta_info */ - int last_txrate_idx; -}; - static s32 iwl3945_expected_tpt_g[IWL_RATE_COUNT_3945] = { 7, 13, 35, 58, 0, 0, 76, 104, 130, 168, 191, 202 }; @@ -370,6 +338,28 @@ static void rs_rate_init(void *priv_r, struct ieee80211_supported_band *sband, IWL_DEBUG_RATE(priv, "enter\n"); + spin_lock_init(&rs_sta->lock); + + rs_sta->priv = priv; + + rs_sta->start_rate = IWL_RATE_INVALID; + + /* default to just 802.11b */ + rs_sta->expected_tpt = iwl3945_expected_tpt_b; + + rs_sta->last_partial_flush = jiffies; + rs_sta->last_flush = jiffies; + rs_sta->flush_time = IWL_RATE_FLUSH; + rs_sta->last_tx_packets = 0; + rs_sta->ibss_sta_added = 0; + + init_timer(&rs_sta->rate_scale_flush); + rs_sta->rate_scale_flush.data = (unsigned long)rs_sta; + rs_sta->rate_scale_flush.function = &iwl3945_bg_rate_scale_flush; + + for (i = 0; i < IWL_RATE_COUNT_3945; i++) + iwl3945_clear_window(&rs_sta->win[i]); + /* TODO: what is a good starting rate for STA? About middle? Maybe not * the lowest or the highest rate.. Could consider using RSSI from * previous packets? Need to have IEEE 802.1X auth succeed immediately @@ -409,45 +399,11 @@ static void *rs_alloc_sta(void *iwl_priv, struct ieee80211_sta *sta, gfp_t gfp) { struct iwl3945_rs_sta *rs_sta; struct iwl3945_sta_priv *psta = (void *) sta->drv_priv; - struct iwl_priv *priv = iwl_priv; - int i; - - /* - * XXX: If it's using sta->drv_priv anyway, it might - * as well just put all the information there. - */ + struct iwl_priv *priv __maybe_unused = iwl_priv; IWL_DEBUG_RATE(priv, "enter\n"); - rs_sta = kzalloc(sizeof(struct iwl3945_rs_sta), gfp); - if (!rs_sta) { - IWL_DEBUG_RATE(priv, "leave: ENOMEM\n"); - return NULL; - } - - psta->rs_sta = rs_sta; - - spin_lock_init(&rs_sta->lock); - - rs_sta->priv = priv; - - rs_sta->start_rate = IWL_RATE_INVALID; - - /* default to just 802.11b */ - rs_sta->expected_tpt = iwl3945_expected_tpt_b; - - rs_sta->last_partial_flush = jiffies; - rs_sta->last_flush = jiffies; - rs_sta->flush_time = IWL_RATE_FLUSH; - rs_sta->last_tx_packets = 0; - rs_sta->ibss_sta_added = 0; - - init_timer(&rs_sta->rate_scale_flush); - rs_sta->rate_scale_flush.data = (unsigned long)rs_sta; - rs_sta->rate_scale_flush.function = &iwl3945_bg_rate_scale_flush; - - for (i = 0; i < IWL_RATE_COUNT_3945; i++) - iwl3945_clear_window(&rs_sta->win[i]); + rs_sta = &psta->rs_sta; IWL_DEBUG_RATE(priv, "leave\n"); @@ -458,14 +414,11 @@ static void rs_free_sta(void *iwl_priv, struct ieee80211_sta *sta, void *priv_sta) { struct iwl3945_sta_priv *psta = (void *) sta->drv_priv; - struct iwl3945_rs_sta *rs_sta = priv_sta; + struct iwl3945_rs_sta *rs_sta = &psta->rs_sta; struct iwl_priv *priv __maybe_unused = rs_sta->priv; - psta->rs_sta = NULL; - IWL_DEBUG_RATE(priv, "enter\n"); del_timer_sync(&rs_sta->rate_scale_flush); - kfree(rs_sta); IWL_DEBUG_RATE(priv, "leave\n"); } @@ -960,14 +913,15 @@ void iwl3945_rate_scale_init(struct ieee80211_hw *hw, s32 sta_id) rcu_read_lock(); - sta = ieee80211_find_sta(hw, priv->stations[sta_id].sta.sta.addr); + sta = ieee80211_find_sta(priv->vif, + priv->stations[sta_id].sta.sta.addr); if (!sta) { rcu_read_unlock(); return; } psta = (void *) sta->drv_priv; - rs_sta = psta->rs_sta; + rs_sta = &psta->rs_sta; spin_lock_irqsave(&rs_sta->lock, flags); diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h index ebb999a..2b0d65c 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945.h @@ -74,8 +74,41 @@ extern struct pci_device_id iwl3945_hw_card_ids[]; /* Module parameters accessible from iwl-*.c */ extern struct iwl_mod_params iwl3945_mod_params; +struct iwl3945_rate_scale_data { + u64 data; + s32 success_counter; + s32 success_ratio; + s32 counter; + s32 average_tpt; + unsigned long stamp; +}; + +struct iwl3945_rs_sta { + spinlock_t lock; + struct iwl_priv *priv; + s32 *expected_tpt; + unsigned long last_partial_flush; + unsigned long last_flush; + u32 flush_time; + u32 last_tx_packets; + u32 tx_packets; + u8 tgg; + u8 flush_pending; + u8 start_rate; + u8 ibss_sta_added; + struct timer_list rate_scale_flush; + struct iwl3945_rate_scale_data win[IWL_RATE_COUNT_3945]; +#ifdef CONFIG_MAC80211_DEBUGFS + struct dentry *rs_sta_dbgfs_stats_table_file; +#endif + + /* used to be in sta_info */ + int last_txrate_idx; +}; + + struct iwl3945_sta_priv { - struct iwl3945_rs_sta *rs_sta; + struct iwl3945_rs_sta rs_sta; }; enum iwl3945_antenna { diff --git a/drivers/net/wireless/iwlwifi/iwl-5000.c b/drivers/net/wireless/iwlwifi/iwl-5000.c index d256fec..910217f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-5000.c +++ b/drivers/net/wireless/iwlwifi/iwl-5000.c @@ -591,16 +591,6 @@ static void iwl5000_tx_queue_set_status(struct iwl_priv *priv, scd_retry ? "BA" : "AC", txq_id, tx_fifo_id); } -static int iwl5000_send_wimax_coex(struct iwl_priv *priv) -{ - struct iwl_wimax_coex_cmd coex_cmd; - - memset(&coex_cmd, 0, sizeof(coex_cmd)); - - return iwl_send_cmd_pdu(priv, COEX_PRIORITY_TABLE_CMD, - sizeof(coex_cmd), &coex_cmd); -} - int iwl5000_alive_notify(struct iwl_priv *priv) { u32 a; @@ -681,7 +671,7 @@ int iwl5000_alive_notify(struct iwl_priv *priv) spin_unlock_irqrestore(&priv->lock, flags); - iwl5000_send_wimax_coex(priv); + iwl_send_wimax_coex(priv); iwl5000_set_Xtal_calib(priv); iwl_send_calib_results(priv); diff --git a/drivers/net/wireless/iwlwifi/iwl-6000.c b/drivers/net/wireless/iwlwifi/iwl-6000.c index 32466d3..70e117f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-6000.c +++ b/drivers/net/wireless/iwlwifi/iwl-6000.c @@ -299,7 +299,7 @@ struct iwl_cfg iwl6000h_2agn_cfg = { .valid_tx_ant = ANT_AB, .valid_rx_ant = ANT_AB, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_HYBRID, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -329,7 +329,7 @@ struct iwl_cfg iwl6000h_2abg_cfg = { .valid_tx_ant = ANT_AB, .valid_rx_ant = ANT_AB, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_HYBRID, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -358,7 +358,7 @@ struct iwl_cfg iwl6000h_2bg_cfg = { .valid_tx_ant = ANT_AB, .valid_rx_ant = ANT_AB, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_HYBRID, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -390,7 +390,7 @@ struct iwl_cfg iwl6000i_2agn_cfg = { .valid_tx_ant = ANT_BC, .valid_rx_ant = ANT_BC, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_INTERNAL, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -420,7 +420,7 @@ struct iwl_cfg iwl6000i_2abg_cfg = { .valid_tx_ant = ANT_BC, .valid_rx_ant = ANT_BC, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_INTERNAL, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -449,7 +449,7 @@ struct iwl_cfg iwl6000i_2bg_cfg = { .valid_tx_ant = ANT_BC, .valid_rx_ant = ANT_BC, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_INTERNAL, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -478,7 +478,7 @@ struct iwl_cfg iwl6050_2agn_cfg = { .valid_tx_ant = ANT_AB, .valid_rx_ant = ANT_AB, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_SYSTEM, .max_ll_items = OTP_MAX_LL_ITEMS_6x50, @@ -490,6 +490,8 @@ struct iwl_cfg iwl6050_2agn_cfg = { .supports_idle = true, .adv_thermal_throttle = true, .support_ct_kill_exit = true, + .support_sm_ps = true, + .support_wimax_coexist = true, }; struct iwl_cfg iwl6050_2abg_cfg = { @@ -508,7 +510,7 @@ struct iwl_cfg iwl6050_2abg_cfg = { .valid_tx_ant = ANT_AB, .valid_rx_ant = ANT_AB, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_SYSTEM, .max_ll_items = OTP_MAX_LL_ITEMS_6x50, @@ -519,6 +521,7 @@ struct iwl_cfg iwl6050_2abg_cfg = { .supports_idle = true, .adv_thermal_throttle = true, .support_ct_kill_exit = true, + .support_wimax_coexist = true, }; struct iwl_cfg iwl6000_3agn_cfg = { @@ -537,7 +540,7 @@ struct iwl_cfg iwl6000_3agn_cfg = { .valid_tx_ant = ANT_ABC, .valid_rx_ant = ANT_ABC, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_SYSTEM, .max_ll_items = OTP_MAX_LL_ITEMS_6x00, @@ -567,7 +570,7 @@ struct iwl_cfg iwl6050_3agn_cfg = { .valid_tx_ant = ANT_ABC, .valid_rx_ant = ANT_ABC, .pll_cfg_val = 0, - .set_l0s = false, + .set_l0s = true, .use_bsm = false, .pa_type = IWL_PA_SYSTEM, .max_ll_items = OTP_MAX_LL_ITEMS_6x50, @@ -579,6 +582,8 @@ struct iwl_cfg iwl6050_3agn_cfg = { .supports_idle = true, .adv_thermal_throttle = true, .support_ct_kill_exit = true, + .support_sm_ps = true, + .support_wimax_coexist = true, }; MODULE_FIRMWARE(IWL6000_MODULE_FIRMWARE(IWL6000_UCODE_API_MAX)); diff --git a/drivers/net/wireless/iwlwifi/iwl-agn-rs.c b/drivers/net/wireless/iwlwifi/iwl-agn-rs.c index 27d4ece..43edd8f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn-rs.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn-rs.c @@ -2477,19 +2477,12 @@ static void *rs_alloc_sta(void *priv_rate, struct ieee80211_sta *sta, struct iwl_lq_sta *lq_sta; struct iwl_station_priv *sta_priv = (struct iwl_station_priv *) sta->drv_priv; struct iwl_priv *priv; - int i, j; priv = (struct iwl_priv *)priv_rate; IWL_DEBUG_RATE(priv, "create station rate scale window\n"); lq_sta = &sta_priv->lq_sta; - lq_sta->lq.sta_id = 0xff; - - for (j = 0; j < LQ_SIZE; j++) - for (i = 0; i < IWL_RATE_COUNT; i++) - rs_rate_scale_clear_window(&lq_sta->lq_info[j].win[i]); - return lq_sta; } @@ -2502,6 +2495,12 @@ static void rs_rate_init(void *priv_r, struct ieee80211_supported_band *sband, struct ieee80211_sta_ht_cap *ht_cap = &sta->ht_cap; struct iwl_lq_sta *lq_sta = priv_sta; + lq_sta->lq.sta_id = 0xff; + + for (j = 0; j < LQ_SIZE; j++) + for (i = 0; i < IWL_RATE_COUNT; i++) + rs_rate_scale_clear_window(&lq_sta->lq_info[j].win[i]); + lq_sta->flush_timer = 0; lq_sta->supp_rates = sta->supp_rates[sband->band]; for (j = 0; j < LQ_SIZE; j++) diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c index fa1672e..b5fe8f8 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn.c @@ -190,11 +190,7 @@ int iwl_commit_rxon(struct iwl_priv *priv) priv->start_calib = 0; /* Add the broadcast address so we can send broadcast frames */ - if (iwl_rxon_add_station(priv, iwl_bcast_addr, 0) == - IWL_INVALID_STATION) { - IWL_ERR(priv, "Error adding BROADCAST address for transmit.\n"); - return -EIO; - } + iwl_add_bcast_station(priv); /* If we have set the ASSOC_MSK and we are in BSS mode then * add the IWL_AP_ID to the station rate table */ @@ -890,6 +886,7 @@ static void iwl_irq_tasklet_legacy(struct iwl_priv *priv) u32 inta, handled = 0; u32 inta_fh; unsigned long flags; + u32 i; #ifdef CONFIG_IWLWIFI_DEBUG u32 inta_mask; #endif @@ -1007,19 +1004,17 @@ static void iwl_irq_tasklet_legacy(struct iwl_priv *priv) handled |= CSR_INT_BIT_SW_ERR; } - /* uCode wakes up after power-down sleep */ + /* + * uCode wakes up after power-down sleep. + * Tell device about any new tx or host commands enqueued, + * and about any Rx buffers made available while asleep. + */ if (inta & CSR_INT_BIT_WAKEUP) { IWL_DEBUG_ISR(priv, "Wakeup interrupt\n"); iwl_rx_queue_update_write_ptr(priv, &priv->rxq); - iwl_txq_update_write_ptr(priv, &priv->txq[0]); - iwl_txq_update_write_ptr(priv, &priv->txq[1]); - iwl_txq_update_write_ptr(priv, &priv->txq[2]); - iwl_txq_update_write_ptr(priv, &priv->txq[3]); - iwl_txq_update_write_ptr(priv, &priv->txq[4]); - iwl_txq_update_write_ptr(priv, &priv->txq[5]); - + for (i = 0; i < priv->hw_params.max_txq_num; i++) + iwl_txq_update_write_ptr(priv, &priv->txq[i]); priv->isr_stats.wakeup++; - handled |= CSR_INT_BIT_WAKEUP; } @@ -1033,11 +1028,12 @@ static void iwl_irq_tasklet_legacy(struct iwl_priv *priv) handled |= (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX); } + /* This "Tx" DMA channel is used only for loading uCode */ if (inta & CSR_INT_BIT_FH_TX) { - IWL_DEBUG_ISR(priv, "Tx interrupt\n"); + IWL_DEBUG_ISR(priv, "uCode load interrupt\n"); priv->isr_stats.tx++; handled |= CSR_INT_BIT_FH_TX; - /* FH finished to write, send event */ + /* Wake up uCode load routine, now that load is complete */ priv->ucode_write_complete = 1; wake_up_interruptible(&priv->wait_command_queue); } @@ -1234,12 +1230,13 @@ static void iwl_irq_tasklet(struct iwl_priv *priv) iwl_leds_background(priv); } + /* This "Tx" DMA channel is used only for loading uCode */ if (inta & CSR_INT_BIT_FH_TX) { iwl_write32(priv, CSR_FH_INT_STATUS, CSR49_FH_INT_TX_MASK); - IWL_DEBUG_ISR(priv, "Tx interrupt\n"); + IWL_DEBUG_ISR(priv, "uCode load interrupt\n"); priv->isr_stats.tx++; handled |= CSR_INT_BIT_FH_TX; - /* FH finished to write, send event */ + /* Wake up uCode load routine, now that load is complete */ priv->ucode_write_complete = 1; wake_up_interruptible(&priv->wait_command_queue); } @@ -1377,6 +1374,14 @@ static int iwl_read_ucode(struct iwl_priv *priv) IWL_UCODE_API(priv->ucode_ver), IWL_UCODE_SERIAL(priv->ucode_ver)); + snprintf(priv->hw->wiphy->fw_version, + sizeof(priv->hw->wiphy->fw_version), + "%u.%u.%u.%u", + IWL_UCODE_MAJOR(priv->ucode_ver), + IWL_UCODE_MINOR(priv->ucode_ver), + IWL_UCODE_API(priv->ucode_ver), + IWL_UCODE_SERIAL(priv->ucode_ver)); + if (build) IWL_DEBUG_INFO(priv, "Build %u\n", build); @@ -2515,7 +2520,7 @@ void iwl_config_ap(struct iwl_priv *priv) spin_lock_irqsave(&priv->lock, flags); iwl_activate_qos(priv, 1); spin_unlock_irqrestore(&priv->lock, flags); - iwl_rxon_add_station(priv, iwl_bcast_addr, 0); + iwl_add_bcast_station(priv); } iwl_send_beacon_cmd(priv); @@ -2963,6 +2968,100 @@ static void iwl_cancel_deferred_work(struct iwl_priv *priv) del_timer_sync(&priv->statistics_periodic); } +static void iwl_init_hw_rates(struct iwl_priv *priv, + struct ieee80211_rate *rates) +{ + int i; + + for (i = 0; i < IWL_RATE_COUNT_LEGACY; i++) { + rates[i].bitrate = iwl_rates[i].ieee * 5; + rates[i].hw_value = i; /* Rate scaling will work on indexes */ + rates[i].hw_value_short = i; + rates[i].flags = 0; + if ((i >= IWL_FIRST_CCK_RATE) && (i <= IWL_LAST_CCK_RATE)) { + /* + * If CCK != 1M then set short preamble rate flag. + */ + rates[i].flags |= + (iwl_rates[i].plcp == IWL_RATE_1M_PLCP) ? + 0 : IEEE80211_RATE_SHORT_PREAMBLE; + } + } +} + +static int iwl_init_drv(struct iwl_priv *priv) +{ + int ret; + + priv->ibss_beacon = NULL; + + spin_lock_init(&priv->lock); + spin_lock_init(&priv->sta_lock); + spin_lock_init(&priv->hcmd_lock); + + INIT_LIST_HEAD(&priv->free_frames); + + mutex_init(&priv->mutex); + + /* Clear the driver's (not device's) station table */ + iwl_clear_stations_table(priv); + + priv->ieee_channels = NULL; + priv->ieee_rates = NULL; + priv->band = IEEE80211_BAND_2GHZ; + + priv->iw_mode = NL80211_IFTYPE_STATION; + if (priv->cfg->support_sm_ps) + priv->current_ht_config.sm_ps = WLAN_HT_CAP_SM_PS_DYNAMIC; + else + priv->current_ht_config.sm_ps = WLAN_HT_CAP_SM_PS_DISABLED; + + /* Choose which receivers/antennas to use */ + if (priv->cfg->ops->hcmd->set_rxon_chain) + priv->cfg->ops->hcmd->set_rxon_chain(priv); + + iwl_init_scan_params(priv); + + iwl_reset_qos(priv); + + priv->qos_data.qos_active = 0; + priv->qos_data.qos_cap.val = 0; + + priv->rates_mask = IWL_RATES_MASK; + /* Set the tx_power_user_lmt to the lowest power level + * this value will get overwritten by channel max power avg + * from eeprom */ + priv->tx_power_user_lmt = IWL_TX_POWER_TARGET_POWER_MIN; + + ret = iwl_init_channel_map(priv); + if (ret) { + IWL_ERR(priv, "initializing regulatory failed: %d\n", ret); + goto err; + } + + ret = iwlcore_init_geos(priv); + if (ret) { + IWL_ERR(priv, "initializing geos failed: %d\n", ret); + goto err_free_channel_map; + } + iwl_init_hw_rates(priv, priv->ieee_rates); + + return 0; + +err_free_channel_map: + iwl_free_channel_map(priv); +err: + return ret; +} + +static void iwl_uninit_drv(struct iwl_priv *priv) +{ + iwl_calib_free_results(priv); + iwlcore_free_geos(priv); + iwl_free_channel_map(priv); + kfree(priv->scan); +} + static struct attribute *iwl_sysfs_entries[] = { &dev_attr_flags.attr, &dev_attr_filter_flags.attr, @@ -3105,12 +3204,6 @@ static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) goto out_iounmap; } - /* amp init */ - err = priv->cfg->ops->lib->apm_ops.init(priv); - if (err < 0) { - IWL_ERR(priv, "Failed to init APMG\n"); - goto out_iounmap; - } /***************** * 4. Read EEPROM *****************/ diff --git a/drivers/net/wireless/iwlwifi/iwl-calib.c b/drivers/net/wireless/iwlwifi/iwl-calib.c index 1f801eb..d994de7 100644 --- a/drivers/net/wireless/iwlwifi/iwl-calib.c +++ b/drivers/net/wireless/iwlwifi/iwl-calib.c @@ -132,6 +132,7 @@ void iwl_calib_free_results(struct iwl_priv *priv) priv->calib_results[i].buf_len = 0; } } +EXPORT_SYMBOL(iwl_calib_free_results); /***************************************************************************** * RUNTIME calibrations framework diff --git a/drivers/net/wireless/iwlwifi/iwl-commands.h b/drivers/net/wireless/iwlwifi/iwl-commands.h index 954bad6..b62c90e 100644 --- a/drivers/net/wireless/iwlwifi/iwl-commands.h +++ b/drivers/net/wireless/iwlwifi/iwl-commands.h @@ -3503,30 +3503,134 @@ struct iwl_led_cmd { } __attribute__ ((packed)); /* - * Coexistence WIFI/WIMAX Command - * COEX_PRIORITY_TABLE_CMD = 0x5a - * + * station priority table entries + * also used as potential "events" value for both + * COEX_MEDIUM_NOTIFICATION and COEX_EVENT_CMD */ + +/* + * COEX events entry flag masks + * RP - Requested Priority + * WP - Win Medium Priority: priority assigned when the contention has been won + */ +#define COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG (0x1) +#define COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG (0x2) +#define COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG (0x4) + +#define COEX_CU_UNASSOC_IDLE_RP 4 +#define COEX_CU_UNASSOC_MANUAL_SCAN_RP 4 +#define COEX_CU_UNASSOC_AUTO_SCAN_RP 4 +#define COEX_CU_CALIBRATION_RP 4 +#define COEX_CU_PERIODIC_CALIBRATION_RP 4 +#define COEX_CU_CONNECTION_ESTAB_RP 4 +#define COEX_CU_ASSOCIATED_IDLE_RP 4 +#define COEX_CU_ASSOC_MANUAL_SCAN_RP 4 +#define COEX_CU_ASSOC_AUTO_SCAN_RP 4 +#define COEX_CU_ASSOC_ACTIVE_LEVEL_RP 4 +#define COEX_CU_RF_ON_RP 6 +#define COEX_CU_RF_OFF_RP 4 +#define COEX_CU_STAND_ALONE_DEBUG_RP 6 +#define COEX_CU_IPAN_ASSOC_LEVEL_RP 4 +#define COEX_CU_RSRVD1_RP 4 +#define COEX_CU_RSRVD2_RP 4 + +#define COEX_CU_UNASSOC_IDLE_WP 3 +#define COEX_CU_UNASSOC_MANUAL_SCAN_WP 3 +#define COEX_CU_UNASSOC_AUTO_SCAN_WP 3 +#define COEX_CU_CALIBRATION_WP 3 +#define COEX_CU_PERIODIC_CALIBRATION_WP 3 +#define COEX_CU_CONNECTION_ESTAB_WP 3 +#define COEX_CU_ASSOCIATED_IDLE_WP 3 +#define COEX_CU_ASSOC_MANUAL_SCAN_WP 3 +#define COEX_CU_ASSOC_AUTO_SCAN_WP 3 +#define COEX_CU_ASSOC_ACTIVE_LEVEL_WP 3 +#define COEX_CU_RF_ON_WP 3 +#define COEX_CU_RF_OFF_WP 3 +#define COEX_CU_STAND_ALONE_DEBUG_WP 6 +#define COEX_CU_IPAN_ASSOC_LEVEL_WP 3 +#define COEX_CU_RSRVD1_WP 3 +#define COEX_CU_RSRVD2_WP 3 + +#define COEX_UNASSOC_IDLE_FLAGS 0 +#define COEX_UNASSOC_MANUAL_SCAN_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG) +#define COEX_UNASSOC_AUTO_SCAN_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG) +#define COEX_CALIBRATION_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG) +#define COEX_PERIODIC_CALIBRATION_FLAGS 0 +/* + * COEX_CONNECTION_ESTAB: + * we need DELAY_MEDIUM_FREE_NTFY to let WiMAX disconnect from network. + */ +#define COEX_CONNECTION_ESTAB_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \ + COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG) +#define COEX_ASSOCIATED_IDLE_FLAGS 0 +#define COEX_ASSOC_MANUAL_SCAN_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG) +#define COEX_ASSOC_AUTO_SCAN_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG) +#define COEX_ASSOC_ACTIVE_LEVEL_FLAGS 0 +#define COEX_RF_ON_FLAGS 0 +#define COEX_RF_OFF_FLAGS 0 +#define COEX_STAND_ALONE_DEBUG_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG) +#define COEX_IPAN_ASSOC_LEVEL_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \ + COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG) +#define COEX_RSRVD1_FLAGS 0 +#define COEX_RSRVD2_FLAGS 0 +/* + * COEX_CU_RF_ON is the event wrapping all radio ownership. + * We need DELAY_MEDIUM_FREE_NTFY to let WiMAX disconnect from network. + */ +#define COEX_CU_RF_ON_FLAGS \ + (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \ + COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \ + COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG) + + enum { + /* un-association part */ COEX_UNASSOC_IDLE = 0, COEX_UNASSOC_MANUAL_SCAN = 1, COEX_UNASSOC_AUTO_SCAN = 2, + /* calibration */ COEX_CALIBRATION = 3, COEX_PERIODIC_CALIBRATION = 4, + /* connection */ COEX_CONNECTION_ESTAB = 5, + /* association part */ COEX_ASSOCIATED_IDLE = 6, COEX_ASSOC_MANUAL_SCAN = 7, COEX_ASSOC_AUTO_SCAN = 8, COEX_ASSOC_ACTIVE_LEVEL = 9, + /* RF ON/OFF */ COEX_RF_ON = 10, COEX_RF_OFF = 11, COEX_STAND_ALONE_DEBUG = 12, + /* IPAN */ COEX_IPAN_ASSOC_LEVEL = 13, + /* reserved */ COEX_RSRVD1 = 14, COEX_RSRVD2 = 15, COEX_NUM_OF_EVENTS = 16 }; +/* + * Coexistence WIFI/WIMAX Command + * COEX_PRIORITY_TABLE_CMD = 0x5a + * + */ struct iwl_wimax_coex_event_entry { u8 request_prio; u8 win_medium_prio; @@ -3551,6 +3655,55 @@ struct iwl_wimax_coex_cmd { struct iwl_wimax_coex_event_entry sta_prio[COEX_NUM_OF_EVENTS]; } __attribute__ ((packed)); +/* + * Coexistence MEDIUM NOTIFICATION + * COEX_MEDIUM_NOTIFICATION = 0x5b + * + * notification from uCode to host to indicate medium changes + * + */ +/* + * status field + * bit 0 - 2: medium status + * bit 3: medium change indication + * bit 4 - 31: reserved + */ +/* status option values, (0 - 2 bits) */ +#define COEX_MEDIUM_BUSY (0x0) /* radio belongs to WiMAX */ +#define COEX_MEDIUM_ACTIVE (0x1) /* radio belongs to WiFi */ +#define COEX_MEDIUM_PRE_RELEASE (0x2) /* received radio release */ +#define COEX_MEDIUM_MSK (0x7) + +/* send notification status (1 bit) */ +#define COEX_MEDIUM_CHANGED (0x8) +#define COEX_MEDIUM_CHANGED_MSK (0x8) +#define COEX_MEDIUM_SHIFT (3) + +struct iwl_coex_medium_notification { + __le32 status; + __le32 events; +} __attribute__ ((packed)); + +/* + * Coexistence EVENT Command + * COEX_EVENT_CMD = 0x5c + * + * send from host to uCode for coex event request. + */ +/* flags options */ +#define COEX_EVENT_REQUEST_MSK (0x1) + +struct iwl_coex_event_cmd { + u8 flags; + u8 event; + __le16 reserved; +} __attribute__ ((packed)); + +struct iwl_coex_event_resp { + __le32 status; +} __attribute__ ((packed)); + + /****************************************************************************** * (13) * Union of all expected notifications/responses: @@ -3587,6 +3740,8 @@ struct iwl_rx_packet { struct iwl_notif_statistics stats; struct iwl_compressed_ba_resp compressed_ba; struct iwl_missed_beacon_notif missed_beacon; + struct iwl_coex_medium_notification coex_medium_notif; + struct iwl_coex_event_resp coex_event; __le32 status; u8 raw[0]; } u; diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c index d2b56ba..e0b5b4a 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.c +++ b/drivers/net/wireless/iwlwifi/iwl-core.c @@ -46,6 +46,37 @@ MODULE_VERSION(IWLWIFI_VERSION); MODULE_AUTHOR(DRV_COPYRIGHT " " DRV_AUTHOR); MODULE_LICENSE("GPL"); +static struct iwl_wimax_coex_event_entry cu_priorities[COEX_NUM_OF_EVENTS] = { + {COEX_CU_UNASSOC_IDLE_RP, COEX_CU_UNASSOC_IDLE_WP, + 0, COEX_UNASSOC_IDLE_FLAGS}, + {COEX_CU_UNASSOC_MANUAL_SCAN_RP, COEX_CU_UNASSOC_MANUAL_SCAN_WP, + 0, COEX_UNASSOC_MANUAL_SCAN_FLAGS}, + {COEX_CU_UNASSOC_AUTO_SCAN_RP, COEX_CU_UNASSOC_AUTO_SCAN_WP, + 0, COEX_UNASSOC_AUTO_SCAN_FLAGS}, + {COEX_CU_CALIBRATION_RP, COEX_CU_CALIBRATION_WP, + 0, COEX_CALIBRATION_FLAGS}, + {COEX_CU_PERIODIC_CALIBRATION_RP, COEX_CU_PERIODIC_CALIBRATION_WP, + 0, COEX_PERIODIC_CALIBRATION_FLAGS}, + {COEX_CU_CONNECTION_ESTAB_RP, COEX_CU_CONNECTION_ESTAB_WP, + 0, COEX_CONNECTION_ESTAB_FLAGS}, + {COEX_CU_ASSOCIATED_IDLE_RP, COEX_CU_ASSOCIATED_IDLE_WP, + 0, COEX_ASSOCIATED_IDLE_FLAGS}, + {COEX_CU_ASSOC_MANUAL_SCAN_RP, COEX_CU_ASSOC_MANUAL_SCAN_WP, + 0, COEX_ASSOC_MANUAL_SCAN_FLAGS}, + {COEX_CU_ASSOC_AUTO_SCAN_RP, COEX_CU_ASSOC_AUTO_SCAN_WP, + 0, COEX_ASSOC_AUTO_SCAN_FLAGS}, + {COEX_CU_ASSOC_ACTIVE_LEVEL_RP, COEX_CU_ASSOC_ACTIVE_LEVEL_WP, + 0, COEX_ASSOC_ACTIVE_LEVEL_FLAGS}, + {COEX_CU_RF_ON_RP, COEX_CU_RF_ON_WP, 0, COEX_CU_RF_ON_FLAGS}, + {COEX_CU_RF_OFF_RP, COEX_CU_RF_OFF_WP, 0, COEX_RF_OFF_FLAGS}, + {COEX_CU_STAND_ALONE_DEBUG_RP, COEX_CU_STAND_ALONE_DEBUG_WP, + 0, COEX_STAND_ALONE_DEBUG_FLAGS}, + {COEX_CU_IPAN_ASSOC_LEVEL_RP, COEX_CU_IPAN_ASSOC_LEVEL_WP, + 0, COEX_IPAN_ASSOC_LEVEL_FLAGS}, + {COEX_CU_RSRVD1_RP, COEX_CU_RSRVD1_WP, 0, COEX_RSRVD1_FLAGS}, + {COEX_CU_RSRVD2_RP, COEX_CU_RSRVD2_WP, 0, COEX_RSRVD2_FLAGS} +}; + #define IWL_DECLARE_RATE_INFO(r, s, ip, in, rp, rn, pp, np) \ [IWL_RATE_##r##M_INDEX] = { IWL_RATE_##r##M_PLCP, \ IWL_RATE_SISO_##s##M_PLCP, \ @@ -414,8 +445,12 @@ static void iwlcore_init_ht_hw_capab(const struct iwl_priv *priv, if (priv->cfg->ht_greenfield_support) ht_info->cap |= IEEE80211_HT_CAP_GRN_FLD; ht_info->cap |= IEEE80211_HT_CAP_SGI_20; - ht_info->cap |= (IEEE80211_HT_CAP_SM_PS & - (WLAN_HT_CAP_SM_PS_DISABLED << 2)); + if (priv->cfg->support_sm_ps) + ht_info->cap |= (IEEE80211_HT_CAP_SM_PS & + (WLAN_HT_CAP_SM_PS_DYNAMIC << 2)); + else + ht_info->cap |= (IEEE80211_HT_CAP_SM_PS & + (WLAN_HT_CAP_SM_PS_DISABLED << 2)); max_bit_rate = MAX_BIT_RATE_20_MHZ; if (priv->hw_params.ht40_channel & BIT(band)) { @@ -451,28 +486,6 @@ static void iwlcore_init_ht_hw_capab(const struct iwl_priv *priv, } } -static void iwlcore_init_hw_rates(struct iwl_priv *priv, - struct ieee80211_rate *rates) -{ - int i; - - for (i = 0; i < IWL_RATE_COUNT_LEGACY; i++) { - rates[i].bitrate = iwl_rates[i].ieee * 5; - rates[i].hw_value = i; /* Rate scaling will work on indexes */ - rates[i].hw_value_short = i; - rates[i].flags = 0; - if ((i >= IWL_FIRST_CCK_RATE) && (i <= IWL_LAST_CCK_RATE)) { - /* - * If CCK != 1M then set short preamble rate flag. - */ - rates[i].flags |= - (iwl_rates[i].plcp == IWL_RATE_1M_PLCP) ? - 0 : IEEE80211_RATE_SHORT_PREAMBLE; - } - } -} - - /** * iwlcore_init_geos - Initialize mac80211's geo/channel info based from eeprom */ @@ -985,17 +998,35 @@ static int iwl_get_active_rx_chain_count(struct iwl_priv *priv) } /* - * When we are in power saving, there's no difference between - * using multiple chains or just a single chain, but due to the - * lack of SM PS we lose a lot of throughput if we use just a - * single chain. - * - * Therefore, use the active count here (which will use multiple - * chains unless connected to a legacy AP). + * When we are in power saving mode, unless device support spatial + * multiplexing power save, use the active count for rx chain count. */ static int iwl_get_idle_rx_chain_count(struct iwl_priv *priv, int active_cnt) { - return active_cnt; + int idle_cnt = active_cnt; + bool is_cam = !test_bit(STATUS_POWER_PMI, &priv->status); + + if (priv->cfg->support_sm_ps) { + /* # Rx chains when idling and maybe trying to save power */ + switch (priv->current_ht_config.sm_ps) { + case WLAN_HT_CAP_SM_PS_STATIC: + case WLAN_HT_CAP_SM_PS_DYNAMIC: + idle_cnt = (is_cam) ? IWL_NUM_IDLE_CHAINS_DUAL : + IWL_NUM_IDLE_CHAINS_SINGLE; + break; + case WLAN_HT_CAP_SM_PS_DISABLED: + idle_cnt = (is_cam) ? active_cnt : + IWL_NUM_IDLE_CHAINS_SINGLE; + break; + case WLAN_HT_CAP_SM_PS_INVALID: + default: + IWL_ERR(priv, "invalid sm_ps mode %d\n", + priv->current_ht_config.sm_ps); + WARN_ON(1); + break; + } + } + return idle_cnt; } /* up to 4 chains */ @@ -1353,39 +1384,39 @@ EXPORT_SYMBOL(iwl_irq_handle_error); int iwl_apm_stop_master(struct iwl_priv *priv) { - unsigned long flags; - - spin_lock_irqsave(&priv->lock, flags); + int ret = 0; - /* set stop master bit */ + /* stop device's busmaster DMA activity */ iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_STOP_MASTER); - iwl_poll_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_MASTER_DISABLED, + ret = iwl_poll_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_MASTER_DISABLED, CSR_RESET_REG_FLAG_MASTER_DISABLED, 100); + if (ret) + IWL_WARN(priv, "Master Disable Timed Out, 100 usec\n"); - spin_unlock_irqrestore(&priv->lock, flags); IWL_DEBUG_INFO(priv, "stop master\n"); - return 0; + return ret; } EXPORT_SYMBOL(iwl_apm_stop_master); void iwl_apm_stop(struct iwl_priv *priv) { - unsigned long flags; - IWL_DEBUG_INFO(priv, "Stop card, put in low power state\n"); + /* Stop device's DMA activity */ iwl_apm_stop_master(priv); - spin_lock_irqsave(&priv->lock, flags); - + /* Reset the entire device */ iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET); udelay(10); - /* clear "init complete" move adapter D0A* --> D0U state */ + + /* + * Clear "initialization complete" bit to move adapter from + * D0A* (powered-up Active) --> D0U* (Uninitialized) state. + */ iwl_clear_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE); - spin_unlock_irqrestore(&priv->lock, flags); } EXPORT_SYMBOL(iwl_apm_stop); @@ -1430,8 +1461,12 @@ int iwl_apm_init(struct iwl_priv *priv) CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A); /* - * HW bug W/A - costs negligible power consumption ... - * Check if BIOS (or OS) enabled L1-ASPM on this device + * HW bug W/A for instability in PCIe bus L0->L0S->L1 transition. + * Check if BIOS (or OS) enabled L1-ASPM on this device. + * If so (likely), disable L0S, so device moves directly L0->L1; + * costs negligible amount of power savings. + * If not (unlikely), enable L0S, so there is at least some + * power savings, even without L1. */ if (priv->cfg->set_l0s) { lctl = iwl_pcie_link_ctl(priv); @@ -1567,68 +1602,6 @@ int iwl_set_hw_params(struct iwl_priv *priv) } EXPORT_SYMBOL(iwl_set_hw_params); -int iwl_init_drv(struct iwl_priv *priv) -{ - int ret; - - priv->ibss_beacon = NULL; - - spin_lock_init(&priv->lock); - spin_lock_init(&priv->sta_lock); - spin_lock_init(&priv->hcmd_lock); - - INIT_LIST_HEAD(&priv->free_frames); - - mutex_init(&priv->mutex); - - /* Clear the driver's (not device's) station table */ - iwl_clear_stations_table(priv); - - priv->ieee_channels = NULL; - priv->ieee_rates = NULL; - priv->band = IEEE80211_BAND_2GHZ; - - priv->iw_mode = NL80211_IFTYPE_STATION; - - /* Choose which receivers/antennas to use */ - if (priv->cfg->ops->hcmd->set_rxon_chain) - priv->cfg->ops->hcmd->set_rxon_chain(priv); - - iwl_init_scan_params(priv); - - iwl_reset_qos(priv); - - priv->qos_data.qos_active = 0; - priv->qos_data.qos_cap.val = 0; - - priv->rates_mask = IWL_RATES_MASK; - /* Set the tx_power_user_lmt to the lowest power level - * this value will get overwritten by channel max power avg - * from eeprom */ - priv->tx_power_user_lmt = IWL_TX_POWER_TARGET_POWER_MIN; - - ret = iwl_init_channel_map(priv); - if (ret) { - IWL_ERR(priv, "initializing regulatory failed: %d\n", ret); - goto err; - } - - ret = iwlcore_init_geos(priv); - if (ret) { - IWL_ERR(priv, "initializing geos failed: %d\n", ret); - goto err_free_channel_map; - } - iwlcore_init_hw_rates(priv, priv->ieee_rates); - - return 0; - -err_free_channel_map: - iwl_free_channel_map(priv); -err: - return ret; -} -EXPORT_SYMBOL(iwl_init_drv); - int iwl_set_tx_power(struct iwl_priv *priv, s8 tx_power, bool force) { int ret = 0; @@ -1676,15 +1649,6 @@ int iwl_set_tx_power(struct iwl_priv *priv, s8 tx_power, bool force) } EXPORT_SYMBOL(iwl_set_tx_power); -void iwl_uninit_drv(struct iwl_priv *priv) -{ - iwl_calib_free_results(priv); - iwlcore_free_geos(priv); - iwl_free_channel_map(priv); - kfree(priv->scan); -} -EXPORT_SYMBOL(iwl_uninit_drv); - #define ICT_COUNT (PAGE_SIZE/sizeof(u32)) /* Free dram table */ @@ -2336,7 +2300,7 @@ static void iwl_ht_conf(struct iwl_priv *priv, switch (priv->iw_mode) { case NL80211_IFTYPE_STATION: rcu_read_lock(); - sta = ieee80211_find_sta(priv->hw, priv->bssid); + sta = ieee80211_find_sta(priv->vif, priv->bssid); if (sta) { struct ieee80211_sta_ht_cap *ht_cap = &sta->ht_cap; int maxstreams; @@ -2346,6 +2310,12 @@ static void iwl_ht_conf(struct iwl_priv *priv, >> IEEE80211_HT_MCS_TX_MAX_STREAMS_SHIFT; maxstreams += 1; + ht_conf->sm_ps = + (u8)((ht_cap->cap & IEEE80211_HT_CAP_SM_PS) + >> 2); + IWL_DEBUG_MAC80211(priv, "sm_ps: 0x%x\n", + ht_conf->sm_ps); + if ((ht_cap->mcs.rx_mask[1] == 0) && (ht_cap->mcs.rx_mask[2] == 0)) ht_conf->single_chain_sufficient = true; @@ -2926,6 +2896,34 @@ void iwl_free_txq_mem(struct iwl_priv *priv) } EXPORT_SYMBOL(iwl_free_txq_mem); +int iwl_send_wimax_coex(struct iwl_priv *priv) +{ + struct iwl_wimax_coex_cmd uninitialized_var(coex_cmd); + + if (priv->cfg->support_wimax_coexist) { + /* UnMask wake up src at associated sleep */ + coex_cmd.flags |= COEX_FLAGS_ASSOC_WA_UNMASK_MSK; + + /* UnMask wake up src at unassociated sleep */ + coex_cmd.flags |= COEX_FLAGS_UNASSOC_WA_UNMASK_MSK; + memcpy(coex_cmd.sta_prio, cu_priorities, + sizeof(struct iwl_wimax_coex_event_entry) * + COEX_NUM_OF_EVENTS); + + /* enabling the coexistence feature */ + coex_cmd.flags |= COEX_FLAGS_COEX_ENABLE_MSK; + + /* enabling the priorities tables */ + coex_cmd.flags |= COEX_FLAGS_STA_TABLE_VALID_MSK; + } else { + /* coexistence is disabled */ + memset(&coex_cmd, 0, sizeof(coex_cmd)); + } + return iwl_send_cmd_pdu(priv, COEX_PRIORITY_TABLE_CMD, + sizeof(coex_cmd), &coex_cmd); +} +EXPORT_SYMBOL(iwl_send_wimax_coex); + #ifdef CONFIG_IWLWIFI_DEBUGFS #define IWL_TRAFFIC_DUMP_SIZE (IWL_TRAFFIC_ENTRY_SIZE * IWL_TRAFFIC_ENTRIES) diff --git a/drivers/net/wireless/iwlwifi/iwl-core.h b/drivers/net/wireless/iwlwifi/iwl-core.h index b875dcf..9574d8f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.h +++ b/drivers/net/wireless/iwlwifi/iwl-core.h @@ -228,6 +228,8 @@ struct iwl_mod_params { * @chain_noise_num_beacons: number of beacons used to compute chain noise * @adv_thermal_throttle: support advance thermal throttle * @support_ct_kill_exit: support ct kill exit condition + * @support_sm_ps: support spatial multiplexing power save + * @support_wimax_coexist: support wimax/wifi co-exist * * We enable the driver to be backward compatible wrt API version. The * driver specifies which APIs it supports (with @ucode_api_max being the @@ -283,6 +285,8 @@ struct iwl_cfg { const bool supports_idle; bool adv_thermal_throttle; bool support_ct_kill_exit; + bool support_sm_ps; + const bool support_wimax_coexist; }; /*************************** @@ -316,8 +320,6 @@ void iwl_configure_filter(struct ieee80211_hw *hw, unsigned int *total_flags, u64 multicast); int iwl_hw_nic_init(struct iwl_priv *priv); int iwl_set_hw_params(struct iwl_priv *priv); -int iwl_init_drv(struct iwl_priv *priv); -void iwl_uninit_drv(struct iwl_priv *priv); bool iwl_is_monitor_mode(struct iwl_priv *priv); void iwl_post_associate(struct iwl_priv *priv); void iwl_bss_info_changed(struct ieee80211_hw *hw, @@ -340,6 +342,7 @@ int iwl_alloc_txq_mem(struct iwl_priv *priv); void iwl_free_txq_mem(struct iwl_priv *priv); void iwlcore_rts_tx_cmd_flag(struct ieee80211_tx_info *info, __le32 *tx_flags); +int iwl_send_wimax_coex(struct iwl_priv *priv); #ifdef CONFIG_IWLWIFI_DEBUGFS int iwl_alloc_traffic_mem(struct iwl_priv *priv); void iwl_free_traffic_mem(struct iwl_priv *priv); diff --git a/drivers/net/wireless/iwlwifi/iwl-dev.h b/drivers/net/wireless/iwlwifi/iwl-dev.h index e7ce673..cb2642c 100644 --- a/drivers/net/wireless/iwlwifi/iwl-dev.h +++ b/drivers/net/wireless/iwlwifi/iwl-dev.h @@ -517,6 +517,7 @@ struct iwl_ht_config { bool is_ht; bool is_40mhz; bool single_chain_sufficient; + u8 sm_ps; /* BSS related data */ u8 extension_chan_offset; u8 ht_protection; diff --git a/drivers/net/wireless/iwlwifi/iwl-eeprom.c b/drivers/net/wireless/iwlwifi/iwl-eeprom.c index 9429cb1..8a0709e 100644 --- a/drivers/net/wireless/iwlwifi/iwl-eeprom.c +++ b/drivers/net/wireless/iwlwifi/iwl-eeprom.c @@ -533,6 +533,10 @@ int iwl_eeprom_init(struct iwl_priv *priv) goto err; } if (priv->nvm_device_type == NVM_DEVICE_TYPE_OTP) { + + /* OTP reads require powered-up chip */ + priv->cfg->ops->lib->apm_ops.init(priv); + ret = iwl_init_otp_access(priv); if (ret) { IWL_ERR(priv, "Failed to initialize OTP access.\n"); @@ -563,6 +567,13 @@ int iwl_eeprom_init(struct iwl_priv *priv) e[cache_addr / 2] = eeprom_data; cache_addr += sizeof(u16); } + + /* + * Now that OTP reads are complete, reset chip to save + * power until we load uCode during "up". + */ + priv->cfg->ops->lib->apm_ops.stop(priv); + } else { /* eeprom is an array of 16bit values */ for (addr = 0; addr < sz; addr += sizeof(u16)) { diff --git a/drivers/net/wireless/iwlwifi/iwl-hcmd.c b/drivers/net/wireless/iwlwifi/iwl-hcmd.c index f2a60dc..905645d 100644 --- a/drivers/net/wireless/iwlwifi/iwl-hcmd.c +++ b/drivers/net/wireless/iwlwifi/iwl-hcmd.c @@ -55,6 +55,8 @@ const char *get_cmd_string(u8 cmd) IWL_CMD(REPLY_LEDS_CMD); IWL_CMD(REPLY_TX_LINK_QUALITY_CMD); IWL_CMD(COEX_PRIORITY_TABLE_CMD); + IWL_CMD(COEX_MEDIUM_NOTIFICATION); + IWL_CMD(COEX_EVENT_CMD); IWL_CMD(RADAR_NOTIFICATION); IWL_CMD(REPLY_QUIET_CMD); IWL_CMD(REPLY_CHANNEL_SWITCH); diff --git a/drivers/net/wireless/iwlwifi/iwl-scan.c b/drivers/net/wireless/iwlwifi/iwl-scan.c index 4fca65a..1eb0d0b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-scan.c +++ b/drivers/net/wireless/iwlwifi/iwl-scan.c @@ -401,6 +401,7 @@ void iwl_init_scan_params(struct iwl_priv *priv) if (!priv->scan_tx_ant[IEEE80211_BAND_2GHZ]) priv->scan_tx_ant[IEEE80211_BAND_2GHZ] = ant_idx; } +EXPORT_SYMBOL(iwl_init_scan_params); static int iwl_scan_initiate(struct iwl_priv *priv) { diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c index dc74c16..eba36f7 100644 --- a/drivers/net/wireless/iwlwifi/iwl-sta.c +++ b/drivers/net/wireless/iwlwifi/iwl-sta.c @@ -182,6 +182,11 @@ static void iwl_set_ht_add_station(struct iwl_priv *priv, u8 index, goto done; mimo_ps_mode = (sta_ht_inf->cap & IEEE80211_HT_CAP_SM_PS) >> 2; + IWL_DEBUG_ASSOC(priv, "spatial multiplexing power save mode: %s\n", + (mimo_ps_mode == WLAN_HT_CAP_SM_PS_STATIC) ? + "static" : + (mimo_ps_mode == WLAN_HT_CAP_SM_PS_DYNAMIC) ? + "dynamic" : "disabled"); sta_flags = priv->stations[index].sta.station_flags; @@ -1012,7 +1017,7 @@ int iwl_rxon_add_station(struct iwl_priv *priv, const u8 *addr, bool is_ap) */ if (priv->current_ht_config.is_ht) { rcu_read_lock(); - sta = ieee80211_find_sta(priv->hw, addr); + sta = ieee80211_find_sta(priv->vif, addr); if (sta) { memcpy(&ht_config, &sta->ht_cap, sizeof(ht_config)); cur_ht_config = &ht_config; @@ -1030,6 +1035,68 @@ int iwl_rxon_add_station(struct iwl_priv *priv, const u8 *addr, bool is_ap) EXPORT_SYMBOL(iwl_rxon_add_station); /** + * iwl_sta_init_bcast_lq - Initialize a bcast station's hardware rate table + * + * NOTE: Run REPLY_ADD_STA command to set up station table entry, before + * calling this function (which runs REPLY_TX_LINK_QUALITY_CMD, + * which requires station table entry to exist). + */ +static void iwl_sta_init_bcast_lq(struct iwl_priv *priv) +{ + int i, r; + struct iwl_link_quality_cmd link_cmd = { + .reserved1 = 0, + }; + u32 rate_flags; + + /* Set up the rate scaling to start at selected rate, fall back + * all the way down to 1M in IEEE order, and then spin on 1M */ + if (priv->band == IEEE80211_BAND_5GHZ) + r = IWL_RATE_6M_INDEX; + else + r = IWL_RATE_1M_INDEX; + + for (i = 0; i < LINK_QUAL_MAX_RETRY_NUM; i++) { + rate_flags = 0; + if (r >= IWL_FIRST_CCK_RATE && r <= IWL_LAST_CCK_RATE) + rate_flags |= RATE_MCS_CCK_MSK; + + rate_flags |= first_antenna(priv->hw_params.valid_tx_ant) << + RATE_MCS_ANT_POS; + + link_cmd.rs_table[i].rate_n_flags = + iwl_hw_set_rate_n_flags(iwl_rates[r].plcp, rate_flags); + r = iwl_get_prev_ieee_rate(r); + } + + link_cmd.general_params.single_stream_ant_msk = + first_antenna(priv->hw_params.valid_tx_ant); + link_cmd.general_params.dual_stream_ant_msk = 3; + link_cmd.agg_params.agg_dis_start_th = LINK_QUAL_AGG_DISABLE_START_DEF; + link_cmd.agg_params.agg_time_limit = + cpu_to_le16(LINK_QUAL_AGG_TIME_LIMIT_DEF); + + /* Update the rate scaling for control frame Tx to AP */ + link_cmd.sta_id = priv->hw_params.bcast_sta_id; + + iwl_send_cmd_pdu_async(priv, REPLY_TX_LINK_QUALITY_CMD, + sizeof(link_cmd), &link_cmd, NULL); +} + + +/** + * iwl_add_bcast_station - add broadcast station into station table. + */ +void iwl_add_bcast_station(struct iwl_priv *priv) +{ + iwl_add_station(priv, iwl_bcast_addr, false, CMD_SYNC, NULL); + + /* Set up default rate scaling table in device's station table */ + iwl_sta_init_bcast_lq(priv); +} +EXPORT_SYMBOL(iwl_add_bcast_station); + +/** * iwl_get_sta_id - Find station's index within station table * * If new IBSS station, create new entry in station table diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.h b/drivers/net/wireless/iwlwifi/iwl-sta.h index 6deebad..1c382de 100644 --- a/drivers/net/wireless/iwlwifi/iwl-sta.h +++ b/drivers/net/wireless/iwlwifi/iwl-sta.h @@ -52,6 +52,7 @@ void iwl_update_tkip_key(struct iwl_priv *priv, const u8 *addr, u32 iv32, u16 *phase1key); int iwl_rxon_add_station(struct iwl_priv *priv, const u8 *addr, bool is_ap); +void iwl_add_bcast_station(struct iwl_priv *priv); int iwl_remove_station(struct iwl_priv *priv, const u8 *addr, bool is_ap); void iwl_clear_stations_table(struct iwl_priv *priv); int iwl_get_free_ucode_key_index(struct iwl_priv *priv); diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 8ae4c9b..05e7510 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -979,7 +979,8 @@ int iwl_enqueue_hcmd(struct iwl_priv *priv, struct iwl_host_cmd *cmd) !(cmd->flags & CMD_SIZE_HUGE)); if (iwl_is_rfkill(priv) || iwl_is_ctkill(priv)) { - IWL_DEBUG_INFO(priv, "Not sending command - RF/CT KILL\n"); + IWL_WARN(priv, "Not sending command - %s KILL\n", + iwl_is_rfkill(priv) ? "RF" : "CT"); return -EIO; } @@ -1121,11 +1122,6 @@ static void iwl_hcmd_queue_reclaim(struct iwl_priv *priv, int txq_id, return; } - pci_unmap_single(priv->pci_dev, - pci_unmap_addr(&txq->meta[cmd_idx], mapping), - pci_unmap_len(&txq->meta[cmd_idx], len), - PCI_DMA_BIDIRECTIONAL); - for (idx = iwl_queue_inc_wrap(idx, q->n_bd); q->read_ptr != idx; q->read_ptr = iwl_queue_inc_wrap(q->read_ptr, q->n_bd)) { @@ -1173,6 +1169,11 @@ void iwl_tx_cmd_complete(struct iwl_priv *priv, struct iwl_rx_mem_buffer *rxb) cmd = priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_index]; meta = &priv->txq[IWL_CMD_QUEUE_NUM].meta[cmd_index]; + pci_unmap_single(priv->pci_dev, + pci_unmap_addr(meta, mapping), + pci_unmap_len(meta, len), + PCI_DMA_BIDIRECTIONAL); + /* Input error checking is done when commands are added to queue. */ if (meta->flags & CMD_WANT_SKB) { meta->source->reply_page = (unsigned long)rxb_addr(rxb); diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index bfd7f49..23b31e6 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -2160,6 +2160,14 @@ static int iwl3945_read_ucode(struct iwl_priv *priv) IWL_UCODE_API(priv->ucode_ver), IWL_UCODE_SERIAL(priv->ucode_ver)); + snprintf(priv->hw->wiphy->fw_version, + sizeof(priv->hw->wiphy->fw_version), + "%u.%u.%u.%u", + IWL_UCODE_MAJOR(priv->ucode_ver), + IWL_UCODE_MINOR(priv->ucode_ver), + IWL_UCODE_API(priv->ucode_ver), + IWL_UCODE_SERIAL(priv->ucode_ver)); + IWL_DEBUG_INFO(priv, "f/w package hdr ucode version raw = 0x%x\n", priv->ucode_ver); IWL_DEBUG_INFO(priv, "f/w package hdr runtime inst size = %u\n", @@ -3992,13 +4000,6 @@ static int iwl3945_pci_probe(struct pci_dev *pdev, const struct pci_device_id *e */ spin_lock_init(&priv->reg_lock); - /* amp init */ - err = priv->cfg->ops->lib->apm_ops.init(priv); - if (err < 0) { - IWL_DEBUG_INFO(priv, "Failed to init the card\n"); - goto out_iounmap; - } - /*********************** * 4. Read EEPROM * ********************/ diff --git a/drivers/net/wireless/iwmc3200wifi/Kconfig b/drivers/net/wireless/iwmc3200wifi/Kconfig index 9606b31..b9d34a7 100644 --- a/drivers/net/wireless/iwmc3200wifi/Kconfig +++ b/drivers/net/wireless/iwmc3200wifi/Kconfig @@ -1,6 +1,6 @@ config IWM tristate "Intel Wireless Multicomm 3200 WiFi driver" - depends on MMC && WLAN_80211 && EXPERIMENTAL + depends on MMC && EXPERIMENTAL depends on CFG80211 select FW_LOADER select IWMC3200TOP diff --git a/drivers/net/wireless/libertas/Kconfig b/drivers/net/wireless/libertas/Kconfig index 8f8d75b..30aa9d4 100644 --- a/drivers/net/wireless/libertas/Kconfig +++ b/drivers/net/wireless/libertas/Kconfig @@ -1,6 +1,6 @@ config LIBERTAS tristate "Marvell 8xxx Libertas WLAN driver support" - depends on WLAN_80211 && CFG80211 + depends on CFG80211 select WIRELESS_EXT select WEXT_SPY select LIB80211 diff --git a/drivers/net/wireless/libertas/if_spi.c b/drivers/net/wireless/libertas/if_spi.c index 30d9d0e..d6a48dd 100644 --- a/drivers/net/wireless/libertas/if_spi.c +++ b/drivers/net/wireless/libertas/if_spi.c @@ -32,12 +32,6 @@ #include "dev.h" #include "if_spi.h" -struct if_spi_packet { - struct list_head list; - u16 blen; - u8 buffer[0] __attribute__((aligned(4))); -}; - struct if_spi_card { struct spi_device *spi; struct lbs_private *priv; @@ -66,33 +60,10 @@ struct if_spi_card { struct semaphore spi_thread_terminated; u8 cmd_buffer[IF_SPI_CMD_BUF_SIZE]; - - /* A buffer of incoming packets from libertas core. - * Since we can't sleep in hw_host_to_card, we have to buffer - * them. */ - struct list_head cmd_packet_list; - struct list_head data_packet_list; - - /* Protects cmd_packet_list and data_packet_list */ - spinlock_t buffer_lock; }; static void free_if_spi_card(struct if_spi_card *card) { - struct list_head *cursor, *next; - struct if_spi_packet *packet; - - BUG_ON(card->run_thread); - list_for_each_safe(cursor, next, &card->cmd_packet_list) { - packet = container_of(cursor, struct if_spi_packet, list); - list_del(&packet->list); - kfree(packet); - } - list_for_each_safe(cursor, next, &card->data_packet_list) { - packet = container_of(cursor, struct if_spi_packet, list); - list_del(&packet->list); - kfree(packet); - } spi_set_drvdata(card->spi, NULL); kfree(card); } @@ -774,40 +745,6 @@ out: return err; } -/* Move data or a command from the host to the card. */ -static void if_spi_h2c(struct if_spi_card *card, - struct if_spi_packet *packet, int type) -{ - int err = 0; - u16 int_type, port_reg; - - switch (type) { - case MVMS_DAT: - int_type = IF_SPI_CIC_TX_DOWNLOAD_OVER; - port_reg = IF_SPI_DATA_RDWRPORT_REG; - break; - case MVMS_CMD: - int_type = IF_SPI_CIC_CMD_DOWNLOAD_OVER; - port_reg = IF_SPI_CMD_RDWRPORT_REG; - break; - default: - lbs_pr_err("can't transfer buffer of type %d\n", type); - err = -EINVAL; - goto out; - } - - /* Write the data to the card */ - err = spu_write(card, port_reg, packet->buffer, packet->blen); - if (err) - goto out; - -out: - kfree(packet); - - if (err) - lbs_pr_err("%s: error %d\n", __func__, err); -} - /* Inform the host about a card event */ static void if_spi_e2h(struct if_spi_card *card) { @@ -837,8 +774,6 @@ static int lbs_spi_thread(void *data) int err; struct if_spi_card *card = data; u16 hiStatus; - unsigned long flags; - struct if_spi_packet *packet; while (1) { /* Wait to be woken up by one of two things. First, our ISR @@ -877,43 +812,9 @@ static int lbs_spi_thread(void *data) if (hiStatus & IF_SPI_HIST_CMD_DOWNLOAD_RDY || (card->priv->psstate != PS_STATE_FULL_POWER && (hiStatus & IF_SPI_HIST_TX_DOWNLOAD_RDY))) { - /* This means two things. First of all, - * if there was a previous command sent, the card has - * successfully received it. - * Secondly, it is now ready to download another - * command. - */ lbs_host_to_card_done(card->priv); - - /* Do we have any command packets from the host to - * send? */ - packet = NULL; - spin_lock_irqsave(&card->buffer_lock, flags); - if (!list_empty(&card->cmd_packet_list)) { - packet = (struct if_spi_packet *)(card-> - cmd_packet_list.next); - list_del(&packet->list); - } - spin_unlock_irqrestore(&card->buffer_lock, flags); - - if (packet) - if_spi_h2c(card, packet, MVMS_CMD); } - if (hiStatus & IF_SPI_HIST_TX_DOWNLOAD_RDY) { - /* Do we have any data packets from the host to - * send? */ - packet = NULL; - spin_lock_irqsave(&card->buffer_lock, flags); - if (!list_empty(&card->data_packet_list)) { - packet = (struct if_spi_packet *)(card-> - data_packet_list.next); - list_del(&packet->list); - } - spin_unlock_irqrestore(&card->buffer_lock, flags); - if (packet) - if_spi_h2c(card, packet, MVMS_DAT); - } if (hiStatus & IF_SPI_HIST_CARD_EVENT) if_spi_e2h(card); @@ -942,40 +843,18 @@ static int if_spi_host_to_card(struct lbs_private *priv, u8 type, u8 *buf, u16 nb) { int err = 0; - unsigned long flags; struct if_spi_card *card = priv->card; - struct if_spi_packet *packet; - u16 blen; lbs_deb_enter_args(LBS_DEB_SPI, "type %d, bytes %d", type, nb); - if (nb == 0) { - lbs_pr_err("%s: invalid size requested: %d\n", __func__, nb); - err = -EINVAL; - goto out; - } - blen = ALIGN(nb, 4); - packet = kzalloc(sizeof(struct if_spi_packet) + blen, GFP_ATOMIC); - if (!packet) { - err = -ENOMEM; - goto out; - } - packet->blen = blen; - memcpy(packet->buffer, buf, nb); - memset(packet->buffer + nb, 0, blen - nb); + nb = ALIGN(nb, 4); switch (type) { case MVMS_CMD: - priv->dnld_sent = DNLD_CMD_SENT; - spin_lock_irqsave(&card->buffer_lock, flags); - list_add_tail(&packet->list, &card->cmd_packet_list); - spin_unlock_irqrestore(&card->buffer_lock, flags); + err = spu_write(card, IF_SPI_CMD_RDWRPORT_REG, buf, nb); break; case MVMS_DAT: - priv->dnld_sent = DNLD_DATA_SENT; - spin_lock_irqsave(&card->buffer_lock, flags); - list_add_tail(&packet->list, &card->data_packet_list); - spin_unlock_irqrestore(&card->buffer_lock, flags); + err = spu_write(card, IF_SPI_DATA_RDWRPORT_REG, buf, nb); break; default: lbs_pr_err("can't transfer buffer of type %d", type); @@ -983,9 +862,6 @@ static int if_spi_host_to_card(struct lbs_private *priv, break; } - /* Wake up the spi thread */ - up(&card->spi_ready); -out: lbs_deb_leave_args(LBS_DEB_SPI, "err=%d", err); return err; } @@ -1062,9 +938,6 @@ static int __devinit if_spi_probe(struct spi_device *spi) sema_init(&card->spi_ready, 0); sema_init(&card->spi_thread_terminated, 0); - INIT_LIST_HEAD(&card->cmd_packet_list); - INIT_LIST_HEAD(&card->data_packet_list); - spin_lock_init(&card->buffer_lock); /* Initialize the SPI Interface Unit */ err = spu_init(card, pdata->use_dummy_writes); @@ -1141,6 +1014,9 @@ static int __devinit if_spi_probe(struct spi_device *spi) goto terminate_thread; } + /* poke the IRQ handler so that we don't miss the first interrupt */ + up(&card->spi_ready); + /* Start the card. * This will call register_netdev, and we'll start * getting interrupts... */ diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c index 38cfd79..fc4ec48 100644 --- a/drivers/net/wireless/mac80211_hwsim.c +++ b/drivers/net/wireless/mac80211_hwsim.c @@ -284,7 +284,7 @@ struct mac80211_hwsim_data { struct ieee80211_channel *channel; unsigned long beacon_int; /* in jiffies unit */ unsigned int rx_filter; - int started; + bool started, idle; struct timer_list beacon_timer; enum ps_mode { PS_DISABLED, PS_ENABLED, PS_AUTO_POLL, PS_MANUAL_POLL @@ -365,6 +365,49 @@ static void mac80211_hwsim_monitor_rx(struct ieee80211_hw *hw, } +static void mac80211_hwsim_monitor_ack(struct ieee80211_hw *hw, const u8 *addr) +{ + struct mac80211_hwsim_data *data = hw->priv; + struct sk_buff *skb; + struct hwsim_radiotap_hdr *hdr; + u16 flags; + struct ieee80211_hdr *hdr11; + + if (!netif_running(hwsim_mon)) + return; + + skb = dev_alloc_skb(100); + if (skb == NULL) + return; + + hdr = (struct hwsim_radiotap_hdr *) skb_put(skb, sizeof(*hdr)); + hdr->hdr.it_version = PKTHDR_RADIOTAP_VERSION; + hdr->hdr.it_pad = 0; + hdr->hdr.it_len = cpu_to_le16(sizeof(*hdr)); + hdr->hdr.it_present = cpu_to_le32((1 << IEEE80211_RADIOTAP_FLAGS) | + (1 << IEEE80211_RADIOTAP_CHANNEL)); + hdr->rt_flags = 0; + hdr->rt_rate = 0; + hdr->rt_channel = cpu_to_le16(data->channel->center_freq); + flags = IEEE80211_CHAN_2GHZ; + hdr->rt_chbitmask = cpu_to_le16(flags); + + hdr11 = (struct ieee80211_hdr *) skb_put(skb, 10); + hdr11->frame_control = cpu_to_le16(IEEE80211_FTYPE_CTL | + IEEE80211_STYPE_ACK); + hdr11->duration_id = cpu_to_le16(0); + memcpy(hdr11->addr1, addr, ETH_ALEN); + + skb->dev = hwsim_mon; + skb_set_mac_header(skb, 0); + skb->ip_summed = CHECKSUM_UNNECESSARY; + skb->pkt_type = PACKET_OTHERHOST; + skb->protocol = htons(ETH_P_802_2); + memset(skb->cb, 0, sizeof(skb->cb)); + netif_rx(skb); +} + + static bool hwsim_ps_rx_ok(struct mac80211_hwsim_data *data, struct sk_buff *skb) { @@ -402,6 +445,12 @@ static bool mac80211_hwsim_tx_frame(struct ieee80211_hw *hw, struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); struct ieee80211_rx_status rx_status; + if (data->idle) { + printk(KERN_DEBUG "%s: Trying to TX when idle - reject\n", + wiphy_name(hw->wiphy)); + return false; + } + memset(&rx_status, 0, sizeof(rx_status)); /* TODO: set mactime */ rx_status.freq = data->channel->center_freq; @@ -428,7 +477,8 @@ static bool mac80211_hwsim_tx_frame(struct ieee80211_hw *hw, if (data == data2) continue; - if (!data2->started || !hwsim_ps_rx_ok(data2, skb) || + if (data2->idle || !data2->started || + !hwsim_ps_rx_ok(data2, skb) || !data->channel || !data2->channel || data->channel->center_freq != data2->channel->center_freq || !(data->group & data2->group)) @@ -464,6 +514,10 @@ static int mac80211_hwsim_tx(struct ieee80211_hw *hw, struct sk_buff *skb) } ack = mac80211_hwsim_tx_frame(hw, skb); + if (ack && skb->len >= 16) { + struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data; + mac80211_hwsim_monitor_ack(hw, hdr->addr2); + } txi = IEEE80211_SKB_CB(skb); @@ -571,6 +625,8 @@ static int mac80211_hwsim_config(struct ieee80211_hw *hw, u32 changed) !!(conf->flags & IEEE80211_CONF_IDLE), !!(conf->flags & IEEE80211_CONF_PS)); + data->idle = !!(conf->flags & IEEE80211_CONF_IDLE); + data->channel = conf->channel; if (!data->started || !data->beacon_int) del_timer(&data->beacon_timer); @@ -1045,19 +1101,20 @@ static int __init init_mac80211_hwsim(void) sband->channels = data->channels_2ghz; sband->n_channels = ARRAY_SIZE(hwsim_channels_2ghz); + sband->bitrates = data->rates; + sband->n_bitrates = ARRAY_SIZE(hwsim_rates); break; case IEEE80211_BAND_5GHZ: sband->channels = data->channels_5ghz; sband->n_channels = ARRAY_SIZE(hwsim_channels_5ghz); + sband->bitrates = data->rates + 4; + sband->n_bitrates = ARRAY_SIZE(hwsim_rates) - 4; break; default: break; } - sband->bitrates = data->rates; - sband->n_bitrates = ARRAY_SIZE(hwsim_rates); - sband->ht_cap.ht_supported = true; sband->ht_cap.cap = IEEE80211_HT_CAP_SUP_WIDTH_20_40 | IEEE80211_HT_CAP_GRN_FLD | diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 746532e..2ebfee4 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -12,6 +12,7 @@ #include <linux/init.h> #include <linux/module.h> #include <linux/kernel.h> +#include <linux/sched.h> #include <linux/spinlock.h> #include <linux/list.h> #include <linux/pci.h> @@ -27,18 +28,6 @@ #define MWL8K_NAME KBUILD_MODNAME #define MWL8K_VERSION "0.10" -MODULE_DESCRIPTION(MWL8K_DESC); -MODULE_VERSION(MWL8K_VERSION); -MODULE_AUTHOR("Lennert Buytenhek <buytenh@marvell.com>"); -MODULE_LICENSE("GPL"); - -static DEFINE_PCI_DEVICE_TABLE(mwl8k_table) = { - { PCI_VDEVICE(MARVELL, 0x2a2b), .driver_data = 8687, }, - { PCI_VDEVICE(MARVELL, 0x2a30), .driver_data = 8687, }, - { } -}; -MODULE_DEVICE_TABLE(pci, mwl8k_table); - /* Register definitions */ #define MWL8K_HIU_GEN_PTR 0x00000c10 #define MWL8K_MODE_STA 0x0000005a @@ -88,72 +77,89 @@ MODULE_DEVICE_TABLE(pci, mwl8k_table); MWL8K_A2H_INT_RX_READY | \ MWL8K_A2H_INT_TX_DONE) -/* WME stream classes */ -#define WME_AC_BE 0 /* best effort */ -#define WME_AC_BK 1 /* background */ -#define WME_AC_VI 2 /* video */ -#define WME_AC_VO 3 /* voice */ - #define MWL8K_RX_QUEUES 1 #define MWL8K_TX_QUEUES 4 +struct rxd_ops { + int rxd_size; + void (*rxd_init)(void *rxd, dma_addr_t next_dma_addr); + void (*rxd_refill)(void *rxd, dma_addr_t addr, int len); + int (*rxd_process)(void *rxd, struct ieee80211_rx_status *status); +}; + +struct mwl8k_device_info { + char *part_name; + char *helper_image; + char *fw_image; + struct rxd_ops *rxd_ops; + u16 modes; +}; + struct mwl8k_rx_queue { - int rx_desc_count; + int rxd_count; /* hw receives here */ - int rx_head; + int head; /* refill descs here */ - int rx_tail; + int tail; - struct mwl8k_rx_desc *rx_desc_area; - dma_addr_t rx_desc_dma; - struct sk_buff **rx_skb; + void *rxd; + dma_addr_t rxd_dma; + struct { + struct sk_buff *skb; + DECLARE_PCI_UNMAP_ADDR(dma) + } *buf; }; struct mwl8k_tx_queue { /* hw transmits here */ - int tx_head; + int head; /* sw appends here */ - int tx_tail; + int tail; - struct ieee80211_tx_queue_stats tx_stats; - struct mwl8k_tx_desc *tx_desc_area; - dma_addr_t tx_desc_dma; - struct sk_buff **tx_skb; + struct ieee80211_tx_queue_stats stats; + struct mwl8k_tx_desc *txd; + dma_addr_t txd_dma; + struct sk_buff **skb; }; /* Pointers to the firmware data and meta information about it. */ struct mwl8k_firmware { - /* Microcode */ - struct firmware *ucode; - /* Boot helper code */ struct firmware *helper; + + /* Microcode */ + struct firmware *ucode; }; struct mwl8k_priv { + void __iomem *sram; void __iomem *regs; struct ieee80211_hw *hw; struct pci_dev *pdev; - u8 name[16]; + + struct mwl8k_device_info *device_info; + bool ap_fw; + struct rxd_ops *rxd_ops; /* firmware files and meta data */ struct mwl8k_firmware fw; - u32 part_num; /* firmware access */ struct mutex fw_mutex; struct task_struct *fw_mutex_owner; int fw_mutex_depth; - struct completion *tx_wait; struct completion *hostcmd_wait; /* lock held over TX and TX reap */ spinlock_t tx_lock; + /* TX quiesce completion, protected by fw_mutex and tx_lock */ + struct completion *tx_wait; + struct ieee80211_vif *vif; struct ieee80211_channel *current_channel; @@ -178,10 +184,11 @@ struct mwl8k_priv { /* PHY parameters */ struct ieee80211_supported_band band; struct ieee80211_channel channels[14]; - struct ieee80211_rate rates[12]; + struct ieee80211_rate rates[13]; bool radio_on; bool radio_short_preamble; + bool sniffer_enabled; bool wmm_enabled; /* XXX need to convert this to handle multiple interfaces */ @@ -199,9 +206,6 @@ struct mwl8k_priv { /* Tasklet to reclaim TX descriptors and buffers after tx */ struct tasklet_struct tx_reclaim_task; - - /* Work thread to serialize configuration requests */ - struct workqueue_struct *config_wq; }; /* Per interface specific private data */ @@ -220,7 +224,7 @@ struct mwl8k_vif { * Subset of supported legacy rates. * Intersection of AP and STA supported rates. */ - struct ieee80211_rate legacy_rates[12]; + struct ieee80211_rate legacy_rates[13]; /* number of supported legacy rates */ u8 legacy_nrates; @@ -252,9 +256,10 @@ static const struct ieee80211_rate mwl8k_rates[] = { { .bitrate = 10, .hw_value = 2, }, { .bitrate = 20, .hw_value = 4, }, { .bitrate = 55, .hw_value = 11, }, + { .bitrate = 110, .hw_value = 22, }, + { .bitrate = 220, .hw_value = 44, }, { .bitrate = 60, .hw_value = 12, }, { .bitrate = 90, .hw_value = 18, }, - { .bitrate = 110, .hw_value = 22, }, { .bitrate = 120, .hw_value = 24, }, { .bitrate = 180, .hw_value = 36, }, { .bitrate = 240, .hw_value = 48, }, @@ -270,10 +275,12 @@ static const struct ieee80211_rate mwl8k_rates[] = { /* Firmware command codes */ #define MWL8K_CMD_CODE_DNLD 0x0001 #define MWL8K_CMD_GET_HW_SPEC 0x0003 +#define MWL8K_CMD_SET_HW_SPEC 0x0004 #define MWL8K_CMD_MAC_MULTICAST_ADR 0x0010 #define MWL8K_CMD_GET_STAT 0x0014 #define MWL8K_CMD_RADIO_CONTROL 0x001c #define MWL8K_CMD_RF_TX_POWER 0x001e +#define MWL8K_CMD_RF_ANTENNA 0x0020 #define MWL8K_CMD_SET_PRE_SCAN 0x0107 #define MWL8K_CMD_SET_POST_SCAN 0x0108 #define MWL8K_CMD_SET_RF_CHANNEL 0x010a @@ -287,6 +294,7 @@ static const struct ieee80211_rate mwl8k_rates[] = { #define MWL8K_CMD_MIMO_CONFIG 0x0125 #define MWL8K_CMD_USE_FIXED_RATE 0x0126 #define MWL8K_CMD_ENABLE_SNIFFER 0x0150 +#define MWL8K_CMD_SET_MAC_ADDR 0x0202 #define MWL8K_CMD_SET_RATEADAPT_MODE 0x0203 #define MWL8K_CMD_UPDATE_STADB 0x1123 @@ -299,10 +307,12 @@ static const char *mwl8k_cmd_name(u16 cmd, char *buf, int bufsize) switch (cmd & ~0x8000) { MWL8K_CMDNAME(CODE_DNLD); MWL8K_CMDNAME(GET_HW_SPEC); + MWL8K_CMDNAME(SET_HW_SPEC); MWL8K_CMDNAME(MAC_MULTICAST_ADR); MWL8K_CMDNAME(GET_STAT); MWL8K_CMDNAME(RADIO_CONTROL); MWL8K_CMDNAME(RF_TX_POWER); + MWL8K_CMDNAME(RF_ANTENNA); MWL8K_CMDNAME(SET_PRE_SCAN); MWL8K_CMDNAME(SET_POST_SCAN); MWL8K_CMDNAME(SET_RF_CHANNEL); @@ -316,6 +326,7 @@ static const char *mwl8k_cmd_name(u16 cmd, char *buf, int bufsize) MWL8K_CMDNAME(MIMO_CONFIG); MWL8K_CMDNAME(USE_FIXED_RATE); MWL8K_CMDNAME(ENABLE_SNIFFER); + MWL8K_CMDNAME(SET_MAC_ADDR); MWL8K_CMDNAME(SET_RATEADAPT_MODE); MWL8K_CMDNAME(UPDATE_STADB); default: @@ -353,41 +364,35 @@ static void mwl8k_release_firmware(struct mwl8k_priv *priv) /* Request fw image */ static int mwl8k_request_fw(struct mwl8k_priv *priv, - const char *fname, struct firmware **fw) + const char *fname, struct firmware **fw) { /* release current image */ if (*fw != NULL) mwl8k_release_fw(fw); return request_firmware((const struct firmware **)fw, - fname, &priv->pdev->dev); + fname, &priv->pdev->dev); } -static int mwl8k_request_firmware(struct mwl8k_priv *priv, u32 part_num) +static int mwl8k_request_firmware(struct mwl8k_priv *priv) { - u8 filename[64]; + struct mwl8k_device_info *di = priv->device_info; int rc; - priv->part_num = part_num; - - snprintf(filename, sizeof(filename), - "mwl8k/helper_%u.fw", priv->part_num); - - rc = mwl8k_request_fw(priv, filename, &priv->fw.helper); - if (rc) { - printk(KERN_ERR - "%s Error requesting helper firmware file %s\n", - pci_name(priv->pdev), filename); - return rc; + if (di->helper_image != NULL) { + rc = mwl8k_request_fw(priv, di->helper_image, &priv->fw.helper); + if (rc) { + printk(KERN_ERR "%s: Error requesting helper " + "firmware file %s\n", pci_name(priv->pdev), + di->helper_image); + return rc; + } } - snprintf(filename, sizeof(filename), - "mwl8k/fmimage_%u.fw", priv->part_num); - - rc = mwl8k_request_fw(priv, filename, &priv->fw.ucode); + rc = mwl8k_request_fw(priv, di->fw_image, &priv->fw.ucode); if (rc) { - printk(KERN_ERR "%s Error requesting firmware file %s\n", - pci_name(priv->pdev), filename); + printk(KERN_ERR "%s: Error requesting firmware file %s\n", + pci_name(priv->pdev), di->fw_image); mwl8k_release_fw(&priv->fw.helper); return rc; } @@ -434,6 +439,7 @@ mwl8k_send_fw_load_cmd(struct mwl8k_priv *priv, void *data, int length) break; } + cond_resched(); udelay(1); } while (--loops); @@ -542,43 +548,62 @@ static int mwl8k_feed_fw_image(struct mwl8k_priv *priv, return rc; } -static int mwl8k_load_firmware(struct mwl8k_priv *priv) +static int mwl8k_load_firmware(struct ieee80211_hw *hw) { - int loops, rc; + struct mwl8k_priv *priv = hw->priv; + struct firmware *fw = priv->fw.ucode; + struct mwl8k_device_info *di = priv->device_info; + int rc; + int loops; + + if (!memcmp(fw->data, "\x01\x00\x00\x00", 4)) { + struct firmware *helper = priv->fw.helper; - const u8 *ucode = priv->fw.ucode->data; - size_t ucode_len = priv->fw.ucode->size; - const u8 *helper = priv->fw.helper->data; - size_t helper_len = priv->fw.helper->size; + if (helper == NULL) { + printk(KERN_ERR "%s: helper image needed but none " + "given\n", pci_name(priv->pdev)); + return -EINVAL; + } - if (!memcmp(ucode, "\x01\x00\x00\x00", 4)) { - rc = mwl8k_load_fw_image(priv, helper, helper_len); + rc = mwl8k_load_fw_image(priv, helper->data, helper->size); if (rc) { printk(KERN_ERR "%s: unable to load firmware " - "helper image\n", pci_name(priv->pdev)); + "helper image\n", pci_name(priv->pdev)); return rc; } msleep(1); - rc = mwl8k_feed_fw_image(priv, ucode, ucode_len); + rc = mwl8k_feed_fw_image(priv, fw->data, fw->size); } else { - rc = mwl8k_load_fw_image(priv, ucode, ucode_len); + rc = mwl8k_load_fw_image(priv, fw->data, fw->size); } if (rc) { - printk(KERN_ERR "%s: unable to load firmware data\n", - pci_name(priv->pdev)); + printk(KERN_ERR "%s: unable to load firmware image\n", + pci_name(priv->pdev)); return rc; } - iowrite32(MWL8K_MODE_STA, priv->regs + MWL8K_HIU_GEN_PTR); + if (di->modes & BIT(NL80211_IFTYPE_AP)) + iowrite32(MWL8K_MODE_AP, priv->regs + MWL8K_HIU_GEN_PTR); + else + iowrite32(MWL8K_MODE_STA, priv->regs + MWL8K_HIU_GEN_PTR); msleep(1); loops = 200000; do { - if (ioread32(priv->regs + MWL8K_HIU_INT_CODE) - == MWL8K_FWSTA_READY) + u32 ready_code; + + ready_code = ioread32(priv->regs + MWL8K_HIU_INT_CODE); + if (ready_code == MWL8K_FWAP_READY) { + priv->ap_fw = 1; break; + } else if (ready_code == MWL8K_FWSTA_READY) { + priv->ap_fw = 0; + break; + } + + cond_resched(); udelay(1); } while (--loops); @@ -605,7 +630,7 @@ struct ewc_ht_info { /* Peer Entry flags - used to define the type of the peer node */ #define MWL8K_PEER_TYPE_ACCESSPOINT 2 -#define MWL8K_IEEE_LEGACY_DATA_RATES 12 +#define MWL8K_IEEE_LEGACY_DATA_RATES 13 #define MWL8K_MCS_BITMAP_SIZE 16 struct peer_capability_info { @@ -731,16 +756,96 @@ static inline void mwl8k_add_dma_header(struct sk_buff *skb) /* - * Packet reception. + * Packet reception for 88w8366. */ -#define MWL8K_RX_CTRL_OWNED_BY_HOST 0x02 +struct mwl8k_rxd_8366 { + __le16 pkt_len; + __u8 sq2; + __u8 rate; + __le32 pkt_phys_addr; + __le32 next_rxd_phys_addr; + __le16 qos_control; + __le16 htsig2; + __le32 hw_rssi_info; + __le32 hw_noise_floor_info; + __u8 noise_floor; + __u8 pad0[3]; + __u8 rssi; + __u8 rx_status; + __u8 channel; + __u8 rx_ctrl; +} __attribute__((packed)); -struct mwl8k_rx_desc { +#define MWL8K_8366_RX_CTRL_OWNED_BY_HOST 0x80 + +static void mwl8k_rxd_8366_init(void *_rxd, dma_addr_t next_dma_addr) +{ + struct mwl8k_rxd_8366 *rxd = _rxd; + + rxd->next_rxd_phys_addr = cpu_to_le32(next_dma_addr); + rxd->rx_ctrl = MWL8K_8366_RX_CTRL_OWNED_BY_HOST; +} + +static void mwl8k_rxd_8366_refill(void *_rxd, dma_addr_t addr, int len) +{ + struct mwl8k_rxd_8366 *rxd = _rxd; + + rxd->pkt_len = cpu_to_le16(len); + rxd->pkt_phys_addr = cpu_to_le32(addr); + wmb(); + rxd->rx_ctrl = 0; +} + +static int +mwl8k_rxd_8366_process(void *_rxd, struct ieee80211_rx_status *status) +{ + struct mwl8k_rxd_8366 *rxd = _rxd; + + if (!(rxd->rx_ctrl & MWL8K_8366_RX_CTRL_OWNED_BY_HOST)) + return -1; + rmb(); + + memset(status, 0, sizeof(*status)); + + status->signal = -rxd->rssi; + status->noise = -rxd->noise_floor; + + if (rxd->rate & 0x80) { + status->flag |= RX_FLAG_HT; + status->rate_idx = rxd->rate & 0x7f; + } else { + int i; + + for (i = 0; i < ARRAY_SIZE(mwl8k_rates); i++) { + if (mwl8k_rates[i].hw_value == rxd->rate) { + status->rate_idx = i; + break; + } + } + } + + status->band = IEEE80211_BAND_2GHZ; + status->freq = ieee80211_channel_to_frequency(rxd->channel); + + return le16_to_cpu(rxd->pkt_len); +} + +static struct rxd_ops rxd_8366_ops = { + .rxd_size = sizeof(struct mwl8k_rxd_8366), + .rxd_init = mwl8k_rxd_8366_init, + .rxd_refill = mwl8k_rxd_8366_refill, + .rxd_process = mwl8k_rxd_8366_process, +}; + +/* + * Packet reception for 88w8687. + */ +struct mwl8k_rxd_8687 { __le16 pkt_len; __u8 link_quality; __u8 noise_level; __le32 pkt_phys_addr; - __le32 next_rx_desc_phys_addr; + __le32 next_rxd_phys_addr; __le16 qos_control; __le16 rate_info; __le32 pad0[4]; @@ -752,6 +857,76 @@ struct mwl8k_rx_desc { __u8 pad2[2]; } __attribute__((packed)); +#define MWL8K_8687_RATE_INFO_SHORTPRE 0x8000 +#define MWL8K_8687_RATE_INFO_ANTSELECT(x) (((x) >> 11) & 0x3) +#define MWL8K_8687_RATE_INFO_RATEID(x) (((x) >> 3) & 0x3f) +#define MWL8K_8687_RATE_INFO_40MHZ 0x0004 +#define MWL8K_8687_RATE_INFO_SHORTGI 0x0002 +#define MWL8K_8687_RATE_INFO_MCS_FORMAT 0x0001 + +#define MWL8K_8687_RX_CTRL_OWNED_BY_HOST 0x02 + +static void mwl8k_rxd_8687_init(void *_rxd, dma_addr_t next_dma_addr) +{ + struct mwl8k_rxd_8687 *rxd = _rxd; + + rxd->next_rxd_phys_addr = cpu_to_le32(next_dma_addr); + rxd->rx_ctrl = MWL8K_8687_RX_CTRL_OWNED_BY_HOST; +} + +static void mwl8k_rxd_8687_refill(void *_rxd, dma_addr_t addr, int len) +{ + struct mwl8k_rxd_8687 *rxd = _rxd; + + rxd->pkt_len = cpu_to_le16(len); + rxd->pkt_phys_addr = cpu_to_le32(addr); + wmb(); + rxd->rx_ctrl = 0; +} + +static int +mwl8k_rxd_8687_process(void *_rxd, struct ieee80211_rx_status *status) +{ + struct mwl8k_rxd_8687 *rxd = _rxd; + u16 rate_info; + + if (!(rxd->rx_ctrl & MWL8K_8687_RX_CTRL_OWNED_BY_HOST)) + return -1; + rmb(); + + rate_info = le16_to_cpu(rxd->rate_info); + + memset(status, 0, sizeof(*status)); + + status->signal = -rxd->rssi; + status->noise = -rxd->noise_level; + status->qual = rxd->link_quality; + status->antenna = MWL8K_8687_RATE_INFO_ANTSELECT(rate_info); + status->rate_idx = MWL8K_8687_RATE_INFO_RATEID(rate_info); + + if (rate_info & MWL8K_8687_RATE_INFO_SHORTPRE) + status->flag |= RX_FLAG_SHORTPRE; + if (rate_info & MWL8K_8687_RATE_INFO_40MHZ) + status->flag |= RX_FLAG_40MHZ; + if (rate_info & MWL8K_8687_RATE_INFO_SHORTGI) + status->flag |= RX_FLAG_SHORT_GI; + if (rate_info & MWL8K_8687_RATE_INFO_MCS_FORMAT) + status->flag |= RX_FLAG_HT; + + status->band = IEEE80211_BAND_2GHZ; + status->freq = ieee80211_channel_to_frequency(rxd->channel); + + return le16_to_cpu(rxd->pkt_len); +} + +static struct rxd_ops rxd_8687_ops = { + .rxd_size = sizeof(struct mwl8k_rxd_8687), + .rxd_init = mwl8k_rxd_8687_init, + .rxd_refill = mwl8k_rxd_8687_refill, + .rxd_process = mwl8k_rxd_8687_process, +}; + + #define MWL8K_RX_DESCS 256 #define MWL8K_RX_MAXSZ 3800 @@ -762,43 +937,44 @@ static int mwl8k_rxq_init(struct ieee80211_hw *hw, int index) int size; int i; - rxq->rx_desc_count = 0; - rxq->rx_head = 0; - rxq->rx_tail = 0; + rxq->rxd_count = 0; + rxq->head = 0; + rxq->tail = 0; - size = MWL8K_RX_DESCS * sizeof(struct mwl8k_rx_desc); + size = MWL8K_RX_DESCS * priv->rxd_ops->rxd_size; - rxq->rx_desc_area = - pci_alloc_consistent(priv->pdev, size, &rxq->rx_desc_dma); - if (rxq->rx_desc_area == NULL) { + rxq->rxd = pci_alloc_consistent(priv->pdev, size, &rxq->rxd_dma); + if (rxq->rxd == NULL) { printk(KERN_ERR "%s: failed to alloc RX descriptors\n", - priv->name); + wiphy_name(hw->wiphy)); return -ENOMEM; } - memset(rxq->rx_desc_area, 0, size); + memset(rxq->rxd, 0, size); - rxq->rx_skb = kmalloc(MWL8K_RX_DESCS * - sizeof(*rxq->rx_skb), GFP_KERNEL); - if (rxq->rx_skb == NULL) { + rxq->buf = kmalloc(MWL8K_RX_DESCS * sizeof(*rxq->buf), GFP_KERNEL); + if (rxq->buf == NULL) { printk(KERN_ERR "%s: failed to alloc RX skbuff list\n", - priv->name); - pci_free_consistent(priv->pdev, size, - rxq->rx_desc_area, rxq->rx_desc_dma); + wiphy_name(hw->wiphy)); + pci_free_consistent(priv->pdev, size, rxq->rxd, rxq->rxd_dma); return -ENOMEM; } - memset(rxq->rx_skb, 0, MWL8K_RX_DESCS * sizeof(*rxq->rx_skb)); + memset(rxq->buf, 0, MWL8K_RX_DESCS * sizeof(*rxq->buf)); for (i = 0; i < MWL8K_RX_DESCS; i++) { - struct mwl8k_rx_desc *rx_desc; + int desc_size; + void *rxd; int nexti; + dma_addr_t next_dma_addr; - rx_desc = rxq->rx_desc_area + i; - nexti = (i + 1) % MWL8K_RX_DESCS; + desc_size = priv->rxd_ops->rxd_size; + rxd = rxq->rxd + (i * priv->rxd_ops->rxd_size); - rx_desc->next_rx_desc_phys_addr = - cpu_to_le32(rxq->rx_desc_dma - + nexti * sizeof(*rx_desc)); - rx_desc->rx_ctrl = MWL8K_RX_CTRL_OWNED_BY_HOST; + nexti = i + 1; + if (nexti == MWL8K_RX_DESCS) + nexti = 0; + next_dma_addr = rxq->rxd_dma + (nexti * desc_size); + + priv->rxd_ops->rxd_init(rxd, next_dma_addr); } return 0; @@ -811,27 +987,28 @@ static int rxq_refill(struct ieee80211_hw *hw, int index, int limit) int refilled; refilled = 0; - while (rxq->rx_desc_count < MWL8K_RX_DESCS && limit--) { + while (rxq->rxd_count < MWL8K_RX_DESCS && limit--) { struct sk_buff *skb; + dma_addr_t addr; int rx; + void *rxd; skb = dev_alloc_skb(MWL8K_RX_MAXSZ); if (skb == NULL) break; - rxq->rx_desc_count++; - - rx = rxq->rx_tail; - rxq->rx_tail = (rx + 1) % MWL8K_RX_DESCS; + addr = pci_map_single(priv->pdev, skb->data, + MWL8K_RX_MAXSZ, DMA_FROM_DEVICE); - rxq->rx_desc_area[rx].pkt_phys_addr = - cpu_to_le32(pci_map_single(priv->pdev, skb->data, - MWL8K_RX_MAXSZ, DMA_FROM_DEVICE)); + rxq->rxd_count++; + rx = rxq->tail++; + if (rxq->tail == MWL8K_RX_DESCS) + rxq->tail = 0; + rxq->buf[rx].skb = skb; + pci_unmap_addr_set(&rxq->buf[rx], dma, addr); - rxq->rx_desc_area[rx].pkt_len = cpu_to_le16(MWL8K_RX_MAXSZ); - rxq->rx_skb[rx] = skb; - wmb(); - rxq->rx_desc_area[rx].rx_ctrl = 0; + rxd = rxq->rxd + (rx * priv->rxd_ops->rxd_size); + priv->rxd_ops->rxd_refill(rxd, addr, MWL8K_RX_MAXSZ); refilled++; } @@ -847,24 +1024,24 @@ static void mwl8k_rxq_deinit(struct ieee80211_hw *hw, int index) int i; for (i = 0; i < MWL8K_RX_DESCS; i++) { - if (rxq->rx_skb[i] != NULL) { - unsigned long addr; - - addr = le32_to_cpu(rxq->rx_desc_area[i].pkt_phys_addr); - pci_unmap_single(priv->pdev, addr, MWL8K_RX_MAXSZ, - PCI_DMA_FROMDEVICE); - kfree_skb(rxq->rx_skb[i]); - rxq->rx_skb[i] = NULL; + if (rxq->buf[i].skb != NULL) { + pci_unmap_single(priv->pdev, + pci_unmap_addr(&rxq->buf[i], dma), + MWL8K_RX_MAXSZ, PCI_DMA_FROMDEVICE); + pci_unmap_addr_set(&rxq->buf[i], dma, 0); + + kfree_skb(rxq->buf[i].skb); + rxq->buf[i].skb = NULL; } } - kfree(rxq->rx_skb); - rxq->rx_skb = NULL; + kfree(rxq->buf); + rxq->buf = NULL; pci_free_consistent(priv->pdev, - MWL8K_RX_DESCS * sizeof(struct mwl8k_rx_desc), - rxq->rx_desc_area, rxq->rx_desc_dma); - rxq->rx_desc_area = NULL; + MWL8K_RX_DESCS * priv->rxd_ops->rxd_size, + rxq->rxd, rxq->rxd_dma); + rxq->rxd = NULL; } @@ -880,9 +1057,11 @@ mwl8k_capture_bssid(struct mwl8k_priv *priv, struct ieee80211_hdr *wh) !compare_ether_addr(wh->addr3, priv->capture_bssid); } -static inline void mwl8k_save_beacon(struct mwl8k_priv *priv, - struct sk_buff *skb) +static inline void mwl8k_save_beacon(struct ieee80211_hw *hw, + struct sk_buff *skb) { + struct mwl8k_priv *priv = hw->priv; + priv->capture_beacon = false; memset(priv->capture_bssid, 0, ETH_ALEN); @@ -893,8 +1072,7 @@ static inline void mwl8k_save_beacon(struct mwl8k_priv *priv, */ priv->beacon_skb = skb_copy(skb, GFP_ATOMIC); if (priv->beacon_skb != NULL) - queue_work(priv->config_wq, - &priv->finalize_join_worker); + ieee80211_queue_work(hw, &priv->finalize_join_worker); } static int rxq_process(struct ieee80211_hw *hw, int index, int limit) @@ -904,53 +1082,46 @@ static int rxq_process(struct ieee80211_hw *hw, int index, int limit) int processed; processed = 0; - while (rxq->rx_desc_count && limit--) { - struct mwl8k_rx_desc *rx_desc; + while (rxq->rxd_count && limit--) { struct sk_buff *skb; + void *rxd; + int pkt_len; struct ieee80211_rx_status status; - unsigned long addr; - struct ieee80211_hdr *wh; - rx_desc = rxq->rx_desc_area + rxq->rx_head; - if (!(rx_desc->rx_ctrl & MWL8K_RX_CTRL_OWNED_BY_HOST)) + skb = rxq->buf[rxq->head].skb; + if (skb == NULL) break; - rmb(); - skb = rxq->rx_skb[rxq->rx_head]; - if (skb == NULL) + rxd = rxq->rxd + (rxq->head * priv->rxd_ops->rxd_size); + + pkt_len = priv->rxd_ops->rxd_process(rxd, &status); + if (pkt_len < 0) break; - rxq->rx_skb[rxq->rx_head] = NULL; - rxq->rx_head = (rxq->rx_head + 1) % MWL8K_RX_DESCS; - rxq->rx_desc_count--; + rxq->buf[rxq->head].skb = NULL; - addr = le32_to_cpu(rx_desc->pkt_phys_addr); - pci_unmap_single(priv->pdev, addr, - MWL8K_RX_MAXSZ, PCI_DMA_FROMDEVICE); + pci_unmap_single(priv->pdev, + pci_unmap_addr(&rxq->buf[rxq->head], dma), + MWL8K_RX_MAXSZ, PCI_DMA_FROMDEVICE); + pci_unmap_addr_set(&rxq->buf[rxq->head], dma, 0); - skb_put(skb, le16_to_cpu(rx_desc->pkt_len)); - mwl8k_remove_dma_header(skb); + rxq->head++; + if (rxq->head == MWL8K_RX_DESCS) + rxq->head = 0; + + rxq->rxd_count--; - wh = (struct ieee80211_hdr *)skb->data; + skb_put(skb, pkt_len); + mwl8k_remove_dma_header(skb); /* - * Check for pending join operation. save a copy of - * the beacon and schedule a tasklet to send finalize - * join command to the firmware. + * Check for a pending join operation. Save a + * copy of the beacon and schedule a tasklet to + * send a FINALIZE_JOIN command to the firmware. */ - if (mwl8k_capture_bssid(priv, wh)) - mwl8k_save_beacon(priv, skb); - - memset(&status, 0, sizeof(status)); - status.mactime = 0; - status.signal = -rx_desc->rssi; - status.noise = -rx_desc->noise_level; - status.qual = rx_desc->link_quality; - status.antenna = 1; - status.rate_idx = 1; - status.flag = 0; - status.band = IEEE80211_BAND_2GHZ; - status.freq = ieee80211_channel_to_frequency(rx_desc->channel); + if (mwl8k_capture_bssid(priv, (void *)skb->data)) + mwl8k_save_beacon(hw, skb); + memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status)); ieee80211_rx_irqsafe(hw, skb); @@ -965,24 +1136,10 @@ static int rxq_process(struct ieee80211_hw *hw, int index, int limit) * Packet transmission. */ -/* Transmit queue assignment. */ -enum { - MWL8K_WME_AC_BK = 0, /* background access */ - MWL8K_WME_AC_BE = 1, /* best effort access */ - MWL8K_WME_AC_VI = 2, /* video access */ - MWL8K_WME_AC_VO = 3, /* voice access */ -}; - /* Transmit packet ACK policy */ #define MWL8K_TXD_ACK_POLICY_NORMAL 0 #define MWL8K_TXD_ACK_POLICY_BLOCKACK 3 -#define GET_TXQ(_ac) (\ - ((_ac) == WME_AC_VO) ? MWL8K_WME_AC_VO : \ - ((_ac) == WME_AC_VI) ? MWL8K_WME_AC_VI : \ - ((_ac) == WME_AC_BK) ? MWL8K_WME_AC_BK : \ - MWL8K_WME_AC_BE) - #define MWL8K_TXD_STATUS_OK 0x00000001 #define MWL8K_TXD_STATUS_OK_RETRY 0x00000002 #define MWL8K_TXD_STATUS_OK_MORE_RETRY 0x00000004 @@ -997,7 +1154,7 @@ struct mwl8k_tx_desc { __le32 pkt_phys_addr; __le16 pkt_len; __u8 dest_MAC_addr[ETH_ALEN]; - __le32 next_tx_desc_phys_addr; + __le32 next_txd_phys_addr; __le32 reserved; __le16 rate_info; __u8 peer_id; @@ -1013,44 +1170,40 @@ static int mwl8k_txq_init(struct ieee80211_hw *hw, int index) int size; int i; - memset(&txq->tx_stats, 0, sizeof(struct ieee80211_tx_queue_stats)); - txq->tx_stats.limit = MWL8K_TX_DESCS; - txq->tx_head = 0; - txq->tx_tail = 0; + memset(&txq->stats, 0, sizeof(struct ieee80211_tx_queue_stats)); + txq->stats.limit = MWL8K_TX_DESCS; + txq->head = 0; + txq->tail = 0; size = MWL8K_TX_DESCS * sizeof(struct mwl8k_tx_desc); - txq->tx_desc_area = - pci_alloc_consistent(priv->pdev, size, &txq->tx_desc_dma); - if (txq->tx_desc_area == NULL) { + txq->txd = pci_alloc_consistent(priv->pdev, size, &txq->txd_dma); + if (txq->txd == NULL) { printk(KERN_ERR "%s: failed to alloc TX descriptors\n", - priv->name); + wiphy_name(hw->wiphy)); return -ENOMEM; } - memset(txq->tx_desc_area, 0, size); + memset(txq->txd, 0, size); - txq->tx_skb = kmalloc(MWL8K_TX_DESCS * sizeof(*txq->tx_skb), - GFP_KERNEL); - if (txq->tx_skb == NULL) { + txq->skb = kmalloc(MWL8K_TX_DESCS * sizeof(*txq->skb), GFP_KERNEL); + if (txq->skb == NULL) { printk(KERN_ERR "%s: failed to alloc TX skbuff list\n", - priv->name); - pci_free_consistent(priv->pdev, size, - txq->tx_desc_area, txq->tx_desc_dma); + wiphy_name(hw->wiphy)); + pci_free_consistent(priv->pdev, size, txq->txd, txq->txd_dma); return -ENOMEM; } - memset(txq->tx_skb, 0, MWL8K_TX_DESCS * sizeof(*txq->tx_skb)); + memset(txq->skb, 0, MWL8K_TX_DESCS * sizeof(*txq->skb)); for (i = 0; i < MWL8K_TX_DESCS; i++) { struct mwl8k_tx_desc *tx_desc; int nexti; - tx_desc = txq->tx_desc_area + i; + tx_desc = txq->txd + i; nexti = (i + 1) % MWL8K_TX_DESCS; tx_desc->status = 0; - tx_desc->next_tx_desc_phys_addr = - cpu_to_le32(txq->tx_desc_dma + - nexti * sizeof(*tx_desc)); + tx_desc->next_txd_phys_addr = + cpu_to_le32(txq->txd_dma + nexti * sizeof(*tx_desc)); } return 0; @@ -1065,11 +1218,6 @@ static inline void mwl8k_tx_start(struct mwl8k_priv *priv) ioread32(priv->regs + MWL8K_HIU_INT_CODE); } -static inline int mwl8k_txq_busy(struct mwl8k_priv *priv) -{ - return priv->pending_tx_pkts; -} - struct mwl8k_txq_info { u32 fw_owned; u32 drv_owned; @@ -1089,14 +1237,13 @@ static int mwl8k_scan_tx_ring(struct mwl8k_priv *priv, memset(txinfo, 0, MWL8K_TX_QUEUES * sizeof(struct mwl8k_txq_info)); - spin_lock_bh(&priv->tx_lock); for (count = 0; count < MWL8K_TX_QUEUES; count++) { txq = priv->txq + count; - txinfo[count].len = txq->tx_stats.len; - txinfo[count].head = txq->tx_head; - txinfo[count].tail = txq->tx_tail; + txinfo[count].len = txq->stats.len; + txinfo[count].head = txq->head; + txinfo[count].tail = txq->tail; for (desc = 0; desc < MWL8K_TX_DESCS; desc++) { - tx_desc = txq->tx_desc_area + desc; + tx_desc = txq->txd + desc; status = le32_to_cpu(tx_desc->status); if (status & MWL8K_TXD_STATUS_FW_OWNED) @@ -1108,30 +1255,26 @@ static int mwl8k_scan_tx_ring(struct mwl8k_priv *priv, txinfo[count].unused++; } } - spin_unlock_bh(&priv->tx_lock); return ndescs; } /* - * Must be called with hw->fw_mutex held and tx queues stopped. + * Must be called with priv->fw_mutex held and tx queues stopped. */ static int mwl8k_tx_wait_empty(struct ieee80211_hw *hw) { struct mwl8k_priv *priv = hw->priv; - DECLARE_COMPLETION_ONSTACK(cmd_wait); + DECLARE_COMPLETION_ONSTACK(tx_wait); u32 count; unsigned long timeout; might_sleep(); spin_lock_bh(&priv->tx_lock); - count = mwl8k_txq_busy(priv); - if (count) { - priv->tx_wait = &cmd_wait; - if (priv->radio_on) - mwl8k_tx_start(priv); - } + count = priv->pending_tx_pkts; + if (count) + priv->tx_wait = &tx_wait; spin_unlock_bh(&priv->tx_lock); if (count) { @@ -1139,23 +1282,23 @@ static int mwl8k_tx_wait_empty(struct ieee80211_hw *hw) int index; int newcount; - timeout = wait_for_completion_timeout(&cmd_wait, + timeout = wait_for_completion_timeout(&tx_wait, msecs_to_jiffies(5000)); if (timeout) return 0; spin_lock_bh(&priv->tx_lock); priv->tx_wait = NULL; - newcount = mwl8k_txq_busy(priv); + newcount = priv->pending_tx_pkts; + mwl8k_scan_tx_ring(priv, txinfo); spin_unlock_bh(&priv->tx_lock); printk(KERN_ERR "%s(%u) TIMEDOUT:5000ms Pend:%u-->%u\n", __func__, __LINE__, count, newcount); - mwl8k_scan_tx_ring(priv, txinfo); for (index = 0; index < MWL8K_TX_QUEUES; index++) - printk(KERN_ERR - "TXQ:%u L:%u H:%u T:%u FW:%u DRV:%u U:%u\n", + printk(KERN_ERR "TXQ:%u L:%u H:%u T:%u FW:%u " + "DRV:%u U:%u\n", index, txinfo[index].len, txinfo[index].head, @@ -1181,7 +1324,7 @@ static void mwl8k_txq_reclaim(struct ieee80211_hw *hw, int index, int force) struct mwl8k_tx_queue *txq = priv->txq + index; int wake = 0; - while (txq->tx_stats.len > 0) { + while (txq->stats.len > 0) { int tx; struct mwl8k_tx_desc *tx_desc; unsigned long addr; @@ -1190,8 +1333,8 @@ static void mwl8k_txq_reclaim(struct ieee80211_hw *hw, int index, int force) struct ieee80211_tx_info *info; u32 status; - tx = txq->tx_head; - tx_desc = txq->tx_desc_area + tx; + tx = txq->head; + tx_desc = txq->txd + tx; status = le32_to_cpu(tx_desc->status); @@ -1202,15 +1345,15 @@ static void mwl8k_txq_reclaim(struct ieee80211_hw *hw, int index, int force) ~cpu_to_le32(MWL8K_TXD_STATUS_FW_OWNED); } - txq->tx_head = (tx + 1) % MWL8K_TX_DESCS; - BUG_ON(txq->tx_stats.len == 0); - txq->tx_stats.len--; + txq->head = (tx + 1) % MWL8K_TX_DESCS; + BUG_ON(txq->stats.len == 0); + txq->stats.len--; priv->pending_tx_pkts--; addr = le32_to_cpu(tx_desc->pkt_phys_addr); size = le16_to_cpu(tx_desc->pkt_len); - skb = txq->tx_skb[tx]; - txq->tx_skb[tx] = NULL; + skb = txq->skb[tx]; + txq->skb[tx] = NULL; BUG_ON(skb == NULL); pci_unmap_single(priv->pdev, addr, size, PCI_DMA_TODEVICE); @@ -1243,13 +1386,13 @@ static void mwl8k_txq_deinit(struct ieee80211_hw *hw, int index) mwl8k_txq_reclaim(hw, index, 1); - kfree(txq->tx_skb); - txq->tx_skb = NULL; + kfree(txq->skb); + txq->skb = NULL; pci_free_consistent(priv->pdev, MWL8K_TX_DESCS * sizeof(struct mwl8k_tx_desc), - txq->tx_desc_area, txq->tx_desc_dma); - txq->tx_desc_area = NULL; + txq->txd, txq->txd_dma); + txq->txd = NULL; } static int @@ -1317,7 +1460,7 @@ mwl8k_txq_xmit(struct ieee80211_hw *hw, int index, struct sk_buff *skb) if (pci_dma_mapping_error(priv->pdev, dma)) { printk(KERN_DEBUG "%s: failed to dma map skb, " - "dropping TX frame.\n", priv->name); + "dropping TX frame.\n", wiphy_name(hw->wiphy)); dev_kfree_skb(skb); return NETDEV_TX_OK; } @@ -1326,10 +1469,10 @@ mwl8k_txq_xmit(struct ieee80211_hw *hw, int index, struct sk_buff *skb) txq = priv->txq + index; - BUG_ON(txq->tx_skb[txq->tx_tail] != NULL); - txq->tx_skb[txq->tx_tail] = skb; + BUG_ON(txq->skb[txq->tail] != NULL); + txq->skb[txq->tail] = skb; - tx = txq->tx_desc_area + txq->tx_tail; + tx = txq->txd + txq->tail; tx->data_rate = txdatarate; tx->tx_priority = index; tx->qos_control = cpu_to_le16(qos); @@ -1340,15 +1483,15 @@ mwl8k_txq_xmit(struct ieee80211_hw *hw, int index, struct sk_buff *skb) wmb(); tx->status = cpu_to_le32(MWL8K_TXD_STATUS_FW_OWNED | txstatus); - txq->tx_stats.count++; - txq->tx_stats.len++; + txq->stats.count++; + txq->stats.len++; priv->pending_tx_pkts++; - txq->tx_tail++; - if (txq->tx_tail == MWL8K_TX_DESCS) - txq->tx_tail = 0; + txq->tail++; + if (txq->tail == MWL8K_TX_DESCS) + txq->tail = 0; - if (txq->tx_head == txq->tx_tail) + if (txq->head == txq->tail) ieee80211_stop_queue(hw, index); mwl8k_tx_start(priv); @@ -1431,7 +1574,7 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) unsigned long timeout = 0; u8 buf[32]; - cmd->result = 0xFFFF; + cmd->result = 0xffff; dma_size = le16_to_cpu(cmd->length); dma_addr = pci_map_single(priv->pdev, cmd, dma_size, PCI_DMA_BIDIRECTIONAL); @@ -1464,7 +1607,7 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) if (!timeout) { printk(KERN_ERR "%s: Command %s timeout after %u ms\n", - priv->name, + wiphy_name(hw->wiphy), mwl8k_cmd_name(cmd->code, buf, sizeof(buf)), MWL8K_CMD_TIMEOUT_MS); rc = -ETIMEDOUT; @@ -1472,7 +1615,7 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) rc = cmd->result ? -EINVAL : 0; if (rc) printk(KERN_ERR "%s: Command %s error 0x%x\n", - priv->name, + wiphy_name(hw->wiphy), mwl8k_cmd_name(cmd->code, buf, sizeof(buf)), le16_to_cpu(cmd->result)); } @@ -1481,9 +1624,9 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) } /* - * GET_HW_SPEC. + * CMD_GET_HW_SPEC (STA version). */ -struct mwl8k_cmd_get_hw_spec { +struct mwl8k_cmd_get_hw_spec_sta { struct mwl8k_cmd_pkt header; __u8 hw_rev; __u8 host_interface; @@ -1499,13 +1642,13 @@ struct mwl8k_cmd_get_hw_spec { __le32 tx_queue_ptrs[MWL8K_TX_QUEUES]; __le32 caps2; __le32 num_tx_desc_per_queue; - __le32 total_rx_desc; + __le32 total_rxd; } __attribute__((packed)); -static int mwl8k_cmd_get_hw_spec(struct ieee80211_hw *hw) +static int mwl8k_cmd_get_hw_spec_sta(struct ieee80211_hw *hw) { struct mwl8k_priv *priv = hw->priv; - struct mwl8k_cmd_get_hw_spec *cmd; + struct mwl8k_cmd_get_hw_spec_sta *cmd; int rc; int i; @@ -1518,12 +1661,12 @@ static int mwl8k_cmd_get_hw_spec(struct ieee80211_hw *hw) memset(cmd->perm_addr, 0xff, sizeof(cmd->perm_addr)); cmd->ps_cookie = cpu_to_le32(priv->cookie_dma); - cmd->rx_queue_ptr = cpu_to_le32(priv->rxq[0].rx_desc_dma); + cmd->rx_queue_ptr = cpu_to_le32(priv->rxq[0].rxd_dma); cmd->num_tx_queues = cpu_to_le32(MWL8K_TX_QUEUES); for (i = 0; i < MWL8K_TX_QUEUES; i++) - cmd->tx_queue_ptrs[i] = cpu_to_le32(priv->txq[i].tx_desc_dma); + cmd->tx_queue_ptrs[i] = cpu_to_le32(priv->txq[i].txd_dma); cmd->num_tx_desc_per_queue = cpu_to_le32(MWL8K_TX_DESCS); - cmd->total_rx_desc = cpu_to_le32(MWL8K_RX_DESCS); + cmd->total_rxd = cpu_to_le32(MWL8K_RX_DESCS); rc = mwl8k_post_cmd(hw, &cmd->header); @@ -1539,6 +1682,129 @@ static int mwl8k_cmd_get_hw_spec(struct ieee80211_hw *hw) } /* + * CMD_GET_HW_SPEC (AP version). + */ +struct mwl8k_cmd_get_hw_spec_ap { + struct mwl8k_cmd_pkt header; + __u8 hw_rev; + __u8 host_interface; + __le16 num_wcb; + __le16 num_mcaddrs; + __u8 perm_addr[ETH_ALEN]; + __le16 region_code; + __le16 num_antenna; + __le32 fw_rev; + __le32 wcbbase0; + __le32 rxwrptr; + __le32 rxrdptr; + __le32 ps_cookie; + __le32 wcbbase1; + __le32 wcbbase2; + __le32 wcbbase3; +} __attribute__((packed)); + +static int mwl8k_cmd_get_hw_spec_ap(struct ieee80211_hw *hw) +{ + struct mwl8k_priv *priv = hw->priv; + struct mwl8k_cmd_get_hw_spec_ap *cmd; + int rc; + + cmd = kzalloc(sizeof(*cmd), GFP_KERNEL); + if (cmd == NULL) + return -ENOMEM; + + cmd->header.code = cpu_to_le16(MWL8K_CMD_GET_HW_SPEC); + cmd->header.length = cpu_to_le16(sizeof(*cmd)); + + memset(cmd->perm_addr, 0xff, sizeof(cmd->perm_addr)); + cmd->ps_cookie = cpu_to_le32(priv->cookie_dma); + + rc = mwl8k_post_cmd(hw, &cmd->header); + + if (!rc) { + int off; + + SET_IEEE80211_PERM_ADDR(hw, cmd->perm_addr); + priv->num_mcaddrs = le16_to_cpu(cmd->num_mcaddrs); + priv->fw_rev = le32_to_cpu(cmd->fw_rev); + priv->hw_rev = cmd->hw_rev; + + off = le32_to_cpu(cmd->wcbbase0) & 0xffff; + iowrite32(cpu_to_le32(priv->txq[0].txd_dma), priv->sram + off); + + off = le32_to_cpu(cmd->rxwrptr) & 0xffff; + iowrite32(cpu_to_le32(priv->rxq[0].rxd_dma), priv->sram + off); + + off = le32_to_cpu(cmd->rxrdptr) & 0xffff; + iowrite32(cpu_to_le32(priv->rxq[0].rxd_dma), priv->sram + off); + + off = le32_to_cpu(cmd->wcbbase1) & 0xffff; + iowrite32(cpu_to_le32(priv->txq[1].txd_dma), priv->sram + off); + + off = le32_to_cpu(cmd->wcbbase2) & 0xffff; + iowrite32(cpu_to_le32(priv->txq[2].txd_dma), priv->sram + off); + + off = le32_to_cpu(cmd->wcbbase3) & 0xffff; + iowrite32(cpu_to_le32(priv->txq[3].txd_dma), priv->sram + off); + } + + kfree(cmd); + return rc; +} + +/* + * CMD_SET_HW_SPEC. + */ +struct mwl8k_cmd_set_hw_spec { + struct mwl8k_cmd_pkt header; + __u8 hw_rev; + __u8 host_interface; + __le16 num_mcaddrs; + __u8 perm_addr[ETH_ALEN]; + __le16 region_code; + __le32 fw_rev; + __le32 ps_cookie; + __le32 caps; + __le32 rx_queue_ptr; + __le32 num_tx_queues; + __le32 tx_queue_ptrs[MWL8K_TX_QUEUES]; + __le32 flags; + __le32 num_tx_desc_per_queue; + __le32 total_rxd; +} __attribute__((packed)); + +#define MWL8K_SET_HW_SPEC_FLAG_HOST_DECR_MGMT 0x00000080 + +static int mwl8k_cmd_set_hw_spec(struct ieee80211_hw *hw) +{ + struct mwl8k_priv *priv = hw->priv; + struct mwl8k_cmd_set_hw_spec *cmd; + int rc; + int i; + + cmd = kzalloc(sizeof(*cmd), GFP_KERNEL); + if (cmd == NULL) + return -ENOMEM; + + cmd->header.code = cpu_to_le16(MWL8K_CMD_SET_HW_SPEC); + cmd->header.length = cpu_to_le16(sizeof(*cmd)); + + cmd->ps_cookie = cpu_to_le32(priv->cookie_dma); + cmd->rx_queue_ptr = cpu_to_le32(priv->rxq[0].rxd_dma); + cmd->num_tx_queues = cpu_to_le32(MWL8K_TX_QUEUES); + for (i = 0; i < MWL8K_TX_QUEUES; i++) + cmd->tx_queue_ptrs[i] = cpu_to_le32(priv->txq[i].txd_dma); + cmd->flags = cpu_to_le32(MWL8K_SET_HW_SPEC_FLAG_HOST_DECR_MGMT); + cmd->num_tx_desc_per_queue = cpu_to_le32(MWL8K_TX_DESCS); + cmd->total_rxd = cpu_to_le32(MWL8K_RX_DESCS); + + rc = mwl8k_post_cmd(hw, &cmd->header); + kfree(cmd); + + return rc; +} + +/* * CMD_MAC_MULTICAST_ADR. */ struct mwl8k_cmd_mac_multicast_adr { @@ -1548,19 +1814,23 @@ struct mwl8k_cmd_mac_multicast_adr { __u8 addr[0][ETH_ALEN]; }; -#define MWL8K_ENABLE_RX_MULTICAST 0x000F +#define MWL8K_ENABLE_RX_DIRECTED 0x0001 +#define MWL8K_ENABLE_RX_MULTICAST 0x0002 +#define MWL8K_ENABLE_RX_ALL_MULTICAST 0x0004 +#define MWL8K_ENABLE_RX_BROADCAST 0x0008 static struct mwl8k_cmd_pkt * -__mwl8k_cmd_mac_multicast_adr(struct ieee80211_hw *hw, +__mwl8k_cmd_mac_multicast_adr(struct ieee80211_hw *hw, int allmulti, int mc_count, struct dev_addr_list *mclist) { struct mwl8k_priv *priv = hw->priv; struct mwl8k_cmd_mac_multicast_adr *cmd; int size; - int i; - if (mc_count > priv->num_mcaddrs) - mc_count = priv->num_mcaddrs; + if (allmulti || mc_count > priv->num_mcaddrs) { + allmulti = 1; + mc_count = 0; + } size = sizeof(*cmd) + mc_count * ETH_ALEN; @@ -1570,16 +1840,24 @@ __mwl8k_cmd_mac_multicast_adr(struct ieee80211_hw *hw, cmd->header.code = cpu_to_le16(MWL8K_CMD_MAC_MULTICAST_ADR); cmd->header.length = cpu_to_le16(size); - cmd->action = cpu_to_le16(MWL8K_ENABLE_RX_MULTICAST); - cmd->numaddr = cpu_to_le16(mc_count); - - for (i = 0; i < mc_count && mclist; i++) { - if (mclist->da_addrlen != ETH_ALEN) { - kfree(cmd); - return NULL; + cmd->action = cpu_to_le16(MWL8K_ENABLE_RX_DIRECTED | + MWL8K_ENABLE_RX_BROADCAST); + + if (allmulti) { + cmd->action |= cpu_to_le16(MWL8K_ENABLE_RX_ALL_MULTICAST); + } else if (mc_count) { + int i; + + cmd->action |= cpu_to_le16(MWL8K_ENABLE_RX_MULTICAST); + cmd->numaddr = cpu_to_le16(mc_count); + for (i = 0; i < mc_count && mclist; i++) { + if (mclist->da_addrlen != ETH_ALEN) { + kfree(cmd); + return NULL; + } + memcpy(cmd->addr[i], mclist->da_addr, ETH_ALEN); + mclist = mclist->next; } - memcpy(cmd->addr[i], mclist->da_addr, ETH_ALEN); - mclist = mclist->next; } return &cmd->header; @@ -1590,7 +1868,6 @@ __mwl8k_cmd_mac_multicast_adr(struct ieee80211_hw *hw, */ struct mwl8k_cmd_802_11_get_stat { struct mwl8k_cmd_pkt header; - __le16 action; __le32 stats[64]; } __attribute__((packed)); @@ -1611,7 +1888,6 @@ static int mwl8k_cmd_802_11_get_stat(struct ieee80211_hw *hw, cmd->header.code = cpu_to_le16(MWL8K_CMD_GET_STAT); cmd->header.length = cpu_to_le16(sizeof(*cmd)); - cmd->action = cpu_to_le16(MWL8K_CMD_GET); rc = mwl8k_post_cmd(hw, &cmd->header); if (!rc) { @@ -1727,6 +2003,39 @@ static int mwl8k_cmd_802_11_rf_tx_power(struct ieee80211_hw *hw, int dBm) } /* + * CMD_RF_ANTENNA. + */ +struct mwl8k_cmd_rf_antenna { + struct mwl8k_cmd_pkt header; + __le16 antenna; + __le16 mode; +} __attribute__((packed)); + +#define MWL8K_RF_ANTENNA_RX 1 +#define MWL8K_RF_ANTENNA_TX 2 + +static int +mwl8k_cmd_rf_antenna(struct ieee80211_hw *hw, int antenna, int mask) +{ + struct mwl8k_cmd_rf_antenna *cmd; + int rc; + + cmd = kzalloc(sizeof(*cmd), GFP_KERNEL); + if (cmd == NULL) + return -ENOMEM; + + cmd->header.code = cpu_to_le16(MWL8K_CMD_RF_ANTENNA); + cmd->header.length = cpu_to_le16(sizeof(*cmd)); + cmd->antenna = cpu_to_le16(antenna); + cmd->mode = cpu_to_le16(mask); + + rc = mwl8k_post_cmd(hw, &cmd->header); + kfree(cmd); + + return rc; +} + +/* * CMD_SET_PRE_SCAN. */ struct mwl8k_cmd_set_pre_scan { @@ -1904,6 +2213,46 @@ static int mwl8k_enable_sniffer(struct ieee80211_hw *hw, bool enable) } /* + * CMD_SET_MAC_ADDR. + */ +struct mwl8k_cmd_set_mac_addr { + struct mwl8k_cmd_pkt header; + union { + struct { + __le16 mac_type; + __u8 mac_addr[ETH_ALEN]; + } mbss; + __u8 mac_addr[ETH_ALEN]; + }; +} __attribute__((packed)); + +static int mwl8k_set_mac_addr(struct ieee80211_hw *hw, u8 *mac) +{ + struct mwl8k_priv *priv = hw->priv; + struct mwl8k_cmd_set_mac_addr *cmd; + int rc; + + cmd = kzalloc(sizeof(*cmd), GFP_KERNEL); + if (cmd == NULL) + return -ENOMEM; + + cmd->header.code = cpu_to_le16(MWL8K_CMD_SET_MAC_ADDR); + cmd->header.length = cpu_to_le16(sizeof(*cmd)); + if (priv->ap_fw) { + cmd->mbss.mac_type = 0; + memcpy(cmd->mbss.mac_addr, mac, ETH_ALEN); + } else { + memcpy(cmd->mac_addr, mac, ETH_ALEN); + } + + rc = mwl8k_post_cmd(hw, &cmd->header); + kfree(cmd); + + return rc; +} + + +/* * CMD_SET_RATEADAPT_MODE. */ struct mwl8k_cmd_set_rate_adapt_mode { @@ -2005,17 +2354,34 @@ struct mwl8k_cmd_set_edca_params { /* TX opportunity in units of 32 us */ __le16 txop; - /* Log exponent of max contention period: 0...15*/ - __u8 log_cw_max; + union { + struct { + /* Log exponent of max contention period: 0...15 */ + __le32 log_cw_max; + + /* Log exponent of min contention period: 0...15 */ + __le32 log_cw_min; + + /* Adaptive interframe spacing in units of 32us */ + __u8 aifs; + + /* TX queue to configure */ + __u8 txq; + } ap; + struct { + /* Log exponent of max contention period: 0...15 */ + __u8 log_cw_max; - /* Log exponent of min contention period: 0...15 */ - __u8 log_cw_min; + /* Log exponent of min contention period: 0...15 */ + __u8 log_cw_min; - /* Adaptive interframe spacing in units of 32us */ - __u8 aifs; + /* Adaptive interframe spacing in units of 32us */ + __u8 aifs; - /* TX queue to configure */ - __u8 txq; + /* TX queue to configure */ + __u8 txq; + } sta; + }; } __attribute__((packed)); #define MWL8K_SET_EDCA_CW 0x01 @@ -2031,6 +2397,7 @@ mwl8k_set_edca_params(struct ieee80211_hw *hw, __u8 qnum, __u16 cw_min, __u16 cw_max, __u8 aifs, __u16 txop) { + struct mwl8k_priv *priv = hw->priv; struct mwl8k_cmd_set_edca_params *cmd; int rc; @@ -2038,14 +2405,27 @@ mwl8k_set_edca_params(struct ieee80211_hw *hw, __u8 qnum, if (cmd == NULL) return -ENOMEM; + /* + * Queues 0 (BE) and 1 (BK) are swapped in hardware for + * this call. + */ + qnum ^= !(qnum >> 1); + cmd->header.code = cpu_to_le16(MWL8K_CMD_SET_EDCA_PARAMS); cmd->header.length = cpu_to_le16(sizeof(*cmd)); cmd->action = cpu_to_le16(MWL8K_SET_EDCA_ALL); cmd->txop = cpu_to_le16(txop); - cmd->log_cw_max = (u8)ilog2(cw_max + 1); - cmd->log_cw_min = (u8)ilog2(cw_min + 1); - cmd->aifs = aifs; - cmd->txq = qnum; + if (priv->ap_fw) { + cmd->ap.log_cw_max = cpu_to_le32(ilog2(cw_max + 1)); + cmd->ap.log_cw_min = cpu_to_le32(ilog2(cw_min + 1)); + cmd->ap.aifs = aifs; + cmd->ap.txq = qnum; + } else { + cmd->sta.log_cw_max = (u8)ilog2(cw_max + 1); + cmd->sta.log_cw_min = (u8)ilog2(cw_min + 1); + cmd->sta.aifs = aifs; + cmd->sta.txq = qnum; + } rc = mwl8k_post_cmd(hw, &cmd->header); kfree(cmd); @@ -2093,8 +2473,8 @@ static int mwl8k_finalize_join(struct ieee80211_hw *hw, void *frame, /* XXX TBD Might just have to abort and return an error */ if (payload_len > MWL8K_FJ_BEACON_MAXLEN) printk(KERN_ERR "%s(): WARNING: Incomplete beacon " - "sent to firmware. Sz=%u MAX=%u\n", __func__, - payload_len, MWL8K_FJ_BEACON_MAXLEN); + "sent to firmware. Sz=%u MAX=%u\n", __func__, + payload_len, MWL8K_FJ_BEACON_MAXLEN); if (payload_len > MWL8K_FJ_BEACON_MAXLEN) payload_len = MWL8K_FJ_BEACON_MAXLEN; @@ -2341,9 +2721,10 @@ static int mwl8k_cmd_use_fixed_rate(struct ieee80211_hw *hw, cmd->rate_type = cpu_to_le32(rate_type); if (rate_table != NULL) { - /* Copy over each field manually so - * that bitflipping can be done - */ + /* + * Copy over each field manually so that endian + * conversion can be done. + */ cmd->rate_table.allow_rate_drop = cpu_to_le32(rate_table->allow_rate_drop); cmd->rate_table.num_rates = @@ -2399,7 +2780,7 @@ static irqreturn_t mwl8k_interrupt(int irq, void *dev_id) if (status & MWL8K_A2H_INT_QUEUE_EMPTY) { if (!mutex_is_locked(&priv->fw_mutex) && - priv->radio_on && mwl8k_txq_busy(priv)) + priv->radio_on && priv->pending_tx_pkts) mwl8k_tx_start(priv); } @@ -2418,7 +2799,7 @@ static int mwl8k_tx(struct ieee80211_hw *hw, struct sk_buff *skb) if (priv->current_channel == NULL) { printk(KERN_DEBUG "%s: dropped TX frame since radio " - "disabled\n", priv->name); + "disabled\n", wiphy_name(hw->wiphy)); dev_kfree_skb(skb); return NETDEV_TX_OK; } @@ -2437,7 +2818,7 @@ static int mwl8k_start(struct ieee80211_hw *hw) IRQF_SHARED, MWL8K_NAME, hw); if (rc) { printk(KERN_ERR "%s: failed to register IRQ handler\n", - priv->name); + wiphy_name(hw->wiphy)); return -EIO; } @@ -2451,12 +2832,17 @@ static int mwl8k_start(struct ieee80211_hw *hw) if (!rc) { rc = mwl8k_cmd_802_11_radio_enable(hw); - if (!rc) - rc = mwl8k_cmd_set_pre_scan(hw); + if (!priv->ap_fw) { + if (!rc) + rc = mwl8k_enable_sniffer(hw, 0); - if (!rc) - rc = mwl8k_cmd_set_post_scan(hw, - "\x00\x00\x00\x00\x00\x00"); + if (!rc) + rc = mwl8k_cmd_set_pre_scan(hw); + + if (!rc) + rc = mwl8k_cmd_set_post_scan(hw, + "\x00\x00\x00\x00\x00\x00"); + } if (!rc) rc = mwl8k_cmd_setrateadaptmode(hw, 0); @@ -2464,9 +2850,6 @@ static int mwl8k_start(struct ieee80211_hw *hw) if (!rc) rc = mwl8k_set_wmm(hw, 0); - if (!rc) - rc = mwl8k_enable_sniffer(hw, 0); - mwl8k_fw_unlock(hw); } @@ -2500,9 +2883,6 @@ static void mwl8k_stop(struct ieee80211_hw *hw) /* Stop tx reclaim tasklet */ tasklet_disable(&priv->tx_reclaim_task); - /* Stop config thread */ - flush_workqueue(priv->config_wq); - /* Return all skbs to mac80211 */ for (i = 0; i < MWL8K_TX_QUEUES; i++) mwl8k_txq_reclaim(hw, i, 1); @@ -2526,11 +2906,24 @@ static int mwl8k_add_interface(struct ieee80211_hw *hw, if (conf->type != NL80211_IFTYPE_STATION) return -EINVAL; + /* + * Reject interface creation if sniffer mode is active, as + * STA operation is mutually exclusive with hardware sniffer + * mode. + */ + if (priv->sniffer_enabled) { + printk(KERN_INFO "%s: unable to create STA " + "interface due to sniffer mode being enabled\n", + wiphy_name(hw->wiphy)); + return -EINVAL; + } + /* Clean out driver private area */ mwl8k_vif = MWL8K_VIF(conf->vif); memset(mwl8k_vif, 0, sizeof(*mwl8k_vif)); - /* Save the mac address */ + /* Set and save the mac address */ + mwl8k_set_mac_addr(hw, conf->mac_addr); memcpy(mwl8k_vif->mac_addr, conf->mac_addr, ETH_ALEN); /* Back pointer to parent config block */ @@ -2558,6 +2951,8 @@ static void mwl8k_remove_interface(struct ieee80211_hw *hw, if (priv->vif == NULL) return; + mwl8k_set_mac_addr(hw, "\x00\x00\x00\x00\x00\x00"); + priv->vif = NULL; } @@ -2593,8 +2988,13 @@ static int mwl8k_config(struct ieee80211_hw *hw, u32 changed) if (rc) goto out; - if (mwl8k_cmd_mimo_config(hw, 0x7, 0x7)) - rc = -EINVAL; + if (priv->ap_fw) { + rc = mwl8k_cmd_rf_antenna(hw, MWL8K_RF_ANTENNA_RX, 0x7); + if (!rc) + rc = mwl8k_cmd_rf_antenna(hw, MWL8K_RF_ANTENNA_TX, 0x7); + } else { + rc = mwl8k_cmd_mimo_config(hw, 0x7, 0x7); + } out: mwl8k_fw_unlock(hw); @@ -2681,32 +3081,108 @@ static u64 mwl8k_prepare_multicast(struct ieee80211_hw *hw, { struct mwl8k_cmd_pkt *cmd; - cmd = __mwl8k_cmd_mac_multicast_adr(hw, mc_count, mclist); + /* + * Synthesize and return a command packet that programs the + * hardware multicast address filter. At this point we don't + * know whether FIF_ALLMULTI is being requested, but if it is, + * we'll end up throwing this packet away and creating a new + * one in mwl8k_configure_filter(). + */ + cmd = __mwl8k_cmd_mac_multicast_adr(hw, 0, mc_count, mclist); return (unsigned long)cmd; } +static int +mwl8k_configure_filter_sniffer(struct ieee80211_hw *hw, + unsigned int changed_flags, + unsigned int *total_flags) +{ + struct mwl8k_priv *priv = hw->priv; + + /* + * Hardware sniffer mode is mutually exclusive with STA + * operation, so refuse to enable sniffer mode if a STA + * interface is active. + */ + if (priv->vif != NULL) { + if (net_ratelimit()) + printk(KERN_INFO "%s: not enabling sniffer " + "mode because STA interface is active\n", + wiphy_name(hw->wiphy)); + return 0; + } + + if (!priv->sniffer_enabled) { + if (mwl8k_enable_sniffer(hw, 1)) + return 0; + priv->sniffer_enabled = true; + } + + *total_flags &= FIF_PROMISC_IN_BSS | FIF_ALLMULTI | + FIF_BCN_PRBRESP_PROMISC | FIF_CONTROL | + FIF_OTHER_BSS; + + return 1; +} + static void mwl8k_configure_filter(struct ieee80211_hw *hw, unsigned int changed_flags, unsigned int *total_flags, u64 multicast) { struct mwl8k_priv *priv = hw->priv; - struct mwl8k_cmd_pkt *multicast_adr_cmd; + struct mwl8k_cmd_pkt *cmd = (void *)(unsigned long)multicast; + + /* + * AP firmware doesn't allow fine-grained control over + * the receive filter. + */ + if (priv->ap_fw) { + *total_flags &= FIF_ALLMULTI | FIF_BCN_PRBRESP_PROMISC; + kfree(cmd); + return; + } + + /* + * Enable hardware sniffer mode if FIF_CONTROL or + * FIF_OTHER_BSS is requested. + */ + if (*total_flags & (FIF_CONTROL | FIF_OTHER_BSS) && + mwl8k_configure_filter_sniffer(hw, changed_flags, total_flags)) { + kfree(cmd); + return; + } /* Clear unsupported feature flags */ - *total_flags &= FIF_BCN_PRBRESP_PROMISC; + *total_flags &= FIF_ALLMULTI | FIF_BCN_PRBRESP_PROMISC; if (mwl8k_fw_lock(hw)) return; + if (priv->sniffer_enabled) { + mwl8k_enable_sniffer(hw, 0); + priv->sniffer_enabled = false; + } + if (changed_flags & FIF_BCN_PRBRESP_PROMISC) { - if (*total_flags & FIF_BCN_PRBRESP_PROMISC) + if (*total_flags & FIF_BCN_PRBRESP_PROMISC) { + /* + * Disable the BSS filter. + */ mwl8k_cmd_set_pre_scan(hw); - else { + } else { u8 *bssid; - bssid = "\x00\x00\x00\x00\x00\x00"; + /* + * Enable the BSS filter. + * + * If there is an active STA interface, use that + * interface's BSSID, otherwise use a dummy one + * (where the OUI part needs to be nonzero for + * the BSSID to be accepted by POST_SCAN). + */ + bssid = "\x01\x00\x00\x00\x00\x00"; if (priv->vif != NULL) bssid = MWL8K_VIF(priv->vif)->bssid; @@ -2714,10 +3190,20 @@ static void mwl8k_configure_filter(struct ieee80211_hw *hw, } } - multicast_adr_cmd = (void *)(unsigned long)multicast; - if (multicast_adr_cmd != NULL) { - mwl8k_post_cmd(hw, multicast_adr_cmd); - kfree(multicast_adr_cmd); + /* + * If FIF_ALLMULTI is being requested, throw away the command + * packet that ->prepare_multicast() built and replace it with + * a command packet that enables reception of all multicast + * packets. + */ + if (*total_flags & FIF_ALLMULTI) { + kfree(cmd); + cmd = __mwl8k_cmd_mac_multicast_adr(hw, 1, 0, NULL); + } + + if (cmd != NULL) { + mwl8k_post_cmd(hw, cmd); + kfree(cmd); } mwl8k_fw_unlock(hw); @@ -2762,7 +3248,7 @@ static int mwl8k_get_tx_stats(struct ieee80211_hw *hw, spin_lock_bh(&priv->tx_lock); for (index = 0; index < MWL8K_TX_QUEUES; index++) { txq = priv->txq + index; - memcpy(&stats[index], &txq->tx_stats, + memcpy(&stats[index], &txq->stats, sizeof(struct ieee80211_tx_queue_stats)); } spin_unlock_bh(&priv->tx_lock); @@ -2802,7 +3288,7 @@ static void mwl8k_tx_reclaim_handler(unsigned long data) for (i = 0; i < MWL8K_TX_QUEUES; i++) mwl8k_txq_reclaim(hw, i, 0); - if (priv->tx_wait != NULL && mwl8k_txq_busy(priv) == 0) { + if (priv->tx_wait != NULL && !priv->pending_tx_pkts) { complete(priv->tx_wait); priv->tx_wait = NULL; } @@ -2822,6 +3308,36 @@ static void mwl8k_finalize_join_worker(struct work_struct *work) priv->beacon_skb = NULL; } +enum { + MWL8687 = 0, + MWL8366, +}; + +static struct mwl8k_device_info mwl8k_info_tbl[] __devinitdata = { + { + .part_name = "88w8687", + .helper_image = "mwl8k/helper_8687.fw", + .fw_image = "mwl8k/fmimage_8687.fw", + .rxd_ops = &rxd_8687_ops, + .modes = BIT(NL80211_IFTYPE_STATION), + }, + { + .part_name = "88w8366", + .helper_image = "mwl8k/helper_8366.fw", + .fw_image = "mwl8k/fmimage_8366.fw", + .rxd_ops = &rxd_8366_ops, + .modes = 0, + }, +}; + +static DEFINE_PCI_DEVICE_TABLE(mwl8k_pci_id_table) = { + { PCI_VDEVICE(MARVELL, 0x2a2b), .driver_data = MWL8687, }, + { PCI_VDEVICE(MARVELL, 0x2a30), .driver_data = MWL8687, }, + { PCI_VDEVICE(MARVELL, 0x2a40), .driver_data = MWL8366, }, + { }, +}; +MODULE_DEVICE_TABLE(pci, mwl8k_pci_id_table); + static int __devinit mwl8k_probe(struct pci_dev *pdev, const struct pci_device_id *id) { @@ -2862,17 +3378,34 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, priv = hw->priv; priv->hw = hw; priv->pdev = pdev; + priv->device_info = &mwl8k_info_tbl[id->driver_data]; + priv->rxd_ops = priv->device_info->rxd_ops; + priv->sniffer_enabled = false; priv->wmm_enabled = false; priv->pending_tx_pkts = 0; - strncpy(priv->name, MWL8K_NAME, sizeof(priv->name)); SET_IEEE80211_DEV(hw, &pdev->dev); pci_set_drvdata(pdev, hw); + priv->sram = pci_iomap(pdev, 0, 0x10000); + if (priv->sram == NULL) { + printk(KERN_ERR "%s: Cannot map device SRAM\n", + wiphy_name(hw->wiphy)); + goto err_iounmap; + } + + /* + * If BAR0 is a 32 bit BAR, the register BAR will be BAR1. + * If BAR0 is a 64 bit BAR, the register BAR will be BAR2. + */ priv->regs = pci_iomap(pdev, 1, 0x10000); if (priv->regs == NULL) { - printk(KERN_ERR "%s: Cannot map device memory\n", priv->name); - goto err_iounmap; + priv->regs = pci_iomap(pdev, 2, 0x10000); + if (priv->regs == NULL) { + printk(KERN_ERR "%s: Cannot map device registers\n", + wiphy_name(hw->wiphy)); + goto err_iounmap; + } } memcpy(priv->channels, mwl8k_channels, sizeof(mwl8k_channels)); @@ -2897,7 +3430,7 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, hw->queues = MWL8K_TX_QUEUES; - hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION); + hw->wiphy->interface_modes = priv->device_info->modes; /* Set rssi and noise values to dBm */ hw->flags |= IEEE80211_HW_SIGNAL_DBM | IEEE80211_HW_NOISE_DBM; @@ -2916,11 +3449,6 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, mwl8k_tx_reclaim_handler, (unsigned long)hw); tasklet_disable(&priv->tx_reclaim_task); - /* Config workthread */ - priv->config_wq = create_singlethread_workqueue("mwl8k_config"); - if (priv->config_wq == NULL) - goto err_iounmap; - /* Power management cookie */ priv->cookie = pci_alloc_consistent(priv->pdev, 4, &priv->cookie_dma); if (priv->cookie == NULL) @@ -2934,11 +3462,12 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, mutex_init(&priv->fw_mutex); priv->fw_mutex_owner = NULL; priv->fw_mutex_depth = 0; - priv->tx_wait = NULL; priv->hostcmd_wait = NULL; spin_lock_init(&priv->tx_lock); + priv->tx_wait = NULL; + for (i = 0; i < MWL8K_TX_QUEUES; i++) { rc = mwl8k_txq_init(hw, i); if (rc) @@ -2954,7 +3483,7 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, IRQF_SHARED, MWL8K_NAME, hw); if (rc) { printk(KERN_ERR "%s: failed to register IRQ handler\n", - priv->name); + wiphy_name(hw->wiphy)); goto err_free_queues; } @@ -2962,16 +3491,18 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, mwl8k_hw_reset(priv); /* Ask userland hotplug daemon for the device firmware */ - rc = mwl8k_request_firmware(priv, (u32)id->driver_data); + rc = mwl8k_request_firmware(priv); if (rc) { - printk(KERN_ERR "%s: Firmware files not found\n", priv->name); + printk(KERN_ERR "%s: Firmware files not found\n", + wiphy_name(hw->wiphy)); goto err_free_irq; } /* Load firmware into hardware */ - rc = mwl8k_load_firmware(priv); + rc = mwl8k_load_firmware(hw); if (rc) { - printk(KERN_ERR "%s: Cannot start firmware\n", priv->name); + printk(KERN_ERR "%s: Cannot start firmware\n", + wiphy_name(hw->wiphy)); goto err_stop_firmware; } @@ -2986,16 +3517,31 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, iowrite32(MWL8K_A2H_EVENTS, priv->regs + MWL8K_HIU_A2H_INTERRUPT_MASK); /* Get config data, mac addrs etc */ - rc = mwl8k_cmd_get_hw_spec(hw); + if (priv->ap_fw) { + rc = mwl8k_cmd_get_hw_spec_ap(hw); + if (!rc) + rc = mwl8k_cmd_set_hw_spec(hw); + } else { + rc = mwl8k_cmd_get_hw_spec_sta(hw); + } if (rc) { - printk(KERN_ERR "%s: Cannot initialise firmware\n", priv->name); + printk(KERN_ERR "%s: Cannot initialise firmware\n", + wiphy_name(hw->wiphy)); goto err_stop_firmware; } /* Turn radio off */ rc = mwl8k_cmd_802_11_radio_disable(hw); if (rc) { - printk(KERN_ERR "%s: Cannot disable\n", priv->name); + printk(KERN_ERR "%s: Cannot disable\n", wiphy_name(hw->wiphy)); + goto err_stop_firmware; + } + + /* Clear MAC address */ + rc = mwl8k_set_mac_addr(hw, "\x00\x00\x00\x00\x00\x00"); + if (rc) { + printk(KERN_ERR "%s: Cannot clear MAC address\n", + wiphy_name(hw->wiphy)); goto err_stop_firmware; } @@ -3005,13 +3551,15 @@ static int __devinit mwl8k_probe(struct pci_dev *pdev, rc = ieee80211_register_hw(hw); if (rc) { - printk(KERN_ERR "%s: Cannot register device\n", priv->name); + printk(KERN_ERR "%s: Cannot register device\n", + wiphy_name(hw->wiphy)); goto err_stop_firmware; } - printk(KERN_INFO "%s: 88w%u v%d, %pM, firmware version %u.%u.%u.%u\n", - wiphy_name(hw->wiphy), priv->part_num, priv->hw_rev, - hw->wiphy->perm_addr, + printk(KERN_INFO "%s: %s v%d, %pM, %s firmware %u.%u.%u.%u\n", + wiphy_name(hw->wiphy), priv->device_info->part_name, + priv->hw_rev, hw->wiphy->perm_addr, + priv->ap_fw ? "AP" : "STA", (priv->fw_rev >> 24) & 0xff, (priv->fw_rev >> 16) & 0xff, (priv->fw_rev >> 8) & 0xff, priv->fw_rev & 0xff); @@ -3038,8 +3586,8 @@ err_iounmap: if (priv->regs != NULL) pci_iounmap(pdev, priv->regs); - if (priv->config_wq != NULL) - destroy_workqueue(priv->config_wq); + if (priv->sram != NULL) + pci_iounmap(pdev, priv->sram); pci_set_drvdata(pdev, NULL); ieee80211_free_hw(hw); @@ -3073,9 +3621,6 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) /* Remove tx reclaim tasklet */ tasklet_kill(&priv->tx_reclaim_task); - /* Stop config thread */ - destroy_workqueue(priv->config_wq); - /* Stop hardware */ mwl8k_hw_reset(priv); @@ -3088,10 +3633,10 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) mwl8k_rxq_deinit(hw, 0); - pci_free_consistent(priv->pdev, 4, - priv->cookie, priv->cookie_dma); + pci_free_consistent(priv->pdev, 4, priv->cookie, priv->cookie_dma); pci_iounmap(pdev, priv->regs); + pci_iounmap(pdev, priv->sram); pci_set_drvdata(pdev, NULL); ieee80211_free_hw(hw); pci_release_regions(pdev); @@ -3100,7 +3645,7 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) static struct pci_driver mwl8k_driver = { .name = MWL8K_NAME, - .id_table = mwl8k_table, + .id_table = mwl8k_pci_id_table, .probe = mwl8k_probe, .remove = __devexit_p(mwl8k_remove), .shutdown = __devexit_p(mwl8k_shutdown), @@ -3118,3 +3663,8 @@ static void __exit mwl8k_exit(void) module_init(mwl8k_init); module_exit(mwl8k_exit); + +MODULE_DESCRIPTION(MWL8K_DESC); +MODULE_VERSION(MWL8K_VERSION); +MODULE_AUTHOR("Lennert Buytenhek <buytenh@marvell.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/wireless/netwave_cs.c b/drivers/net/wireless/netwave_cs.c deleted file mode 100644 index 9498b46..0000000 --- a/drivers/net/wireless/netwave_cs.c +++ /dev/null @@ -1,1389 +0,0 @@ -/********************************************************************* - * - * Filename: netwave_cs.c - * Version: 0.4.1 - * Description: Netwave AirSurfer Wireless LAN PC Card driver - * Status: Experimental. - * Authors: John Markus Bjørndalen <johnm@cs.uit.no> - * Dag Brattli <dagb@cs.uit.no> - * David Hinds <dahinds@users.sourceforge.net> - * Created at: A long time ago! - * Modified at: Mon Nov 10 11:54:37 1997 - * Modified by: Dag Brattli <dagb@cs.uit.no> - * - * Copyright (c) 1997 University of Tromsø, Norway - * - * Revision History: - * - * 08-Nov-97 15:14:47 John Markus Bjørndalen <johnm@cs.uit.no> - * - Fixed some bugs in netwave_rx and cleaned it up a bit. - * (One of the bugs would have destroyed packets when receiving - * multiple packets per interrupt). - * - Cleaned up parts of newave_hw_xmit. - * - A few general cleanups. - * 24-Oct-97 13:17:36 Dag Brattli <dagb@cs.uit.no> - * - Fixed netwave_rx receive function (got updated docs) - * Others: - * - Changed name from xircnw to netwave, take a look at - * http://www.netwave-wireless.com - * - Some reorganizing of the code - * - Removed possible race condition between interrupt handler and transmit - * function - * - Started to add wireless extensions, but still needs some coding - * - Added watchdog for better handling of transmission timeouts - * (hopefully this works better) - ********************************************************************/ - -/* To have statistics (just packets sent) define this */ -#undef NETWAVE_STATS - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/fcntl.h> -#include <linux/interrupt.h> -#include <linux/ptrace.h> -#include <linux/ioport.h> -#include <linux/in.h> -#include <linux/slab.h> -#include <linux/string.h> -#include <linux/timer.h> -#include <linux/errno.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/bitops.h> -#include <linux/wireless.h> -#include <net/iw_handler.h> - -#include <pcmcia/cs_types.h> -#include <pcmcia/cs.h> -#include <pcmcia/cistpl.h> -#include <pcmcia/cisreg.h> -#include <pcmcia/ds.h> -#include <pcmcia/mem_op.h> - -#include <asm/system.h> -#include <asm/io.h> -#include <asm/dma.h> - -#define NETWAVE_REGOFF 0x8000 -/* The Netwave IO registers, offsets to iobase */ -#define NETWAVE_REG_COR 0x0 -#define NETWAVE_REG_CCSR 0x2 -#define NETWAVE_REG_ASR 0x4 -#define NETWAVE_REG_IMR 0xa -#define NETWAVE_REG_PMR 0xc -#define NETWAVE_REG_IOLOW 0x6 -#define NETWAVE_REG_IOHI 0x7 -#define NETWAVE_REG_IOCONTROL 0x8 -#define NETWAVE_REG_DATA 0xf -/* The Netwave Extended IO registers, offsets to RamBase */ -#define NETWAVE_EREG_ASCC 0x114 -#define NETWAVE_EREG_RSER 0x120 -#define NETWAVE_EREG_RSERW 0x124 -#define NETWAVE_EREG_TSER 0x130 -#define NETWAVE_EREG_TSERW 0x134 -#define NETWAVE_EREG_CB 0x100 -#define NETWAVE_EREG_SPCQ 0x154 -#define NETWAVE_EREG_SPU 0x155 -#define NETWAVE_EREG_LIF 0x14e -#define NETWAVE_EREG_ISPLQ 0x156 -#define NETWAVE_EREG_HHC 0x158 -#define NETWAVE_EREG_NI 0x16e -#define NETWAVE_EREG_MHS 0x16b -#define NETWAVE_EREG_TDP 0x140 -#define NETWAVE_EREG_RDP 0x150 -#define NETWAVE_EREG_PA 0x160 -#define NETWAVE_EREG_EC 0x180 -#define NETWAVE_EREG_CRBP 0x17a -#define NETWAVE_EREG_ARW 0x166 - -/* - * Commands used in the extended command buffer - * NETWAVE_EREG_CB (0x100-0x10F) - */ -#define NETWAVE_CMD_NOP 0x00 -#define NETWAVE_CMD_SRC 0x01 -#define NETWAVE_CMD_STC 0x02 -#define NETWAVE_CMD_AMA 0x03 -#define NETWAVE_CMD_DMA 0x04 -#define NETWAVE_CMD_SAMA 0x05 -#define NETWAVE_CMD_ER 0x06 -#define NETWAVE_CMD_DR 0x07 -#define NETWAVE_CMD_TL 0x08 -#define NETWAVE_CMD_SRP 0x09 -#define NETWAVE_CMD_SSK 0x0a -#define NETWAVE_CMD_SMD 0x0b -#define NETWAVE_CMD_SAPD 0x0c -#define NETWAVE_CMD_SSS 0x11 -/* End of Command marker */ -#define NETWAVE_CMD_EOC 0x00 - -/* ASR register bits */ -#define NETWAVE_ASR_RXRDY 0x80 -#define NETWAVE_ASR_TXBA 0x01 - -#define TX_TIMEOUT ((32*HZ)/100) - -static const unsigned int imrConfRFU1 = 0x10; /* RFU interrupt mask, keep high */ -static const unsigned int imrConfIENA = 0x02; /* Interrupt enable */ - -static const unsigned int corConfIENA = 0x01; /* Interrupt enable */ -static const unsigned int corConfLVLREQ = 0x40; /* Keep high */ - -static const unsigned int rxConfRxEna = 0x80; /* Receive Enable */ -static const unsigned int rxConfMAC = 0x20; /* MAC host receive mode*/ -static const unsigned int rxConfPro = 0x10; /* Promiscuous */ -static const unsigned int rxConfAMP = 0x08; /* Accept Multicast Packets */ -static const unsigned int rxConfBcast = 0x04; /* Accept Broadcast Packets */ - -static const unsigned int txConfTxEna = 0x80; /* Transmit Enable */ -static const unsigned int txConfMAC = 0x20; /* Host sends MAC mode */ -static const unsigned int txConfEUD = 0x10; /* Enable Uni-Data packets */ -static const unsigned int txConfKey = 0x02; /* Scramble data packets */ -static const unsigned int txConfLoop = 0x01; /* Loopback mode */ - -/* - All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If - you do not define PCMCIA_DEBUG at all, all the debug code will be - left out. If you compile with PCMCIA_DEBUG=0, the debug code will - be present but disabled -- but it can then be enabled for specific - modules at load time with a 'pc_debug=#' option to insmod. -*/ - -#ifdef PCMCIA_DEBUG -static int pc_debug = PCMCIA_DEBUG; -module_param(pc_debug, int, 0); -#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args) -static char *version = -"netwave_cs.c 0.3.0 Thu Jul 17 14:36:02 1997 (John Markus Bjørndalen)\n"; -#else -#define DEBUG(n, args...) -#endif - -/*====================================================================*/ - -/* Parameters that can be set with 'insmod' */ - -/* Choose the domain, default is 0x100 */ -static u_int domain = 0x100; - -/* Scramble key, range from 0x0 to 0xffff. - * 0x0 is no scrambling. - */ -static u_int scramble_key = 0x0; - -/* Shared memory speed, in ns. The documentation states that - * the card should not be read faster than every 400ns. - * This timing should be provided by the HBA. If it becomes a - * problem, try setting mem_speed to 400. - */ -static int mem_speed; - -module_param(domain, int, 0); -module_param(scramble_key, int, 0); -module_param(mem_speed, int, 0); - -/*====================================================================*/ - -/* PCMCIA (Card Services) related functions */ -static void netwave_release(struct pcmcia_device *link); /* Card removal */ -static int netwave_pcmcia_config(struct pcmcia_device *arg); /* Runs after card - insertion */ -static void netwave_detach(struct pcmcia_device *p_dev); /* Destroy instance */ - -/* Hardware configuration */ -static void netwave_doreset(unsigned int iobase, u_char __iomem *ramBase); -static void netwave_reset(struct net_device *dev); - -/* Misc device stuff */ -static int netwave_open(struct net_device *dev); /* Open the device */ -static int netwave_close(struct net_device *dev); /* Close the device */ - -/* Packet transmission and Packet reception */ -static netdev_tx_t netwave_start_xmit( struct sk_buff *skb, - struct net_device *dev); -static int netwave_rx( struct net_device *dev); - -/* Interrupt routines */ -static irqreturn_t netwave_interrupt(int irq, void *dev_id); -static void netwave_watchdog(struct net_device *); - -/* Wireless extensions */ -static struct iw_statistics* netwave_get_wireless_stats(struct net_device *dev); - -static void set_multicast_list(struct net_device *dev); - -/* - A struct pcmcia_device structure has fields for most things that are needed - to keep track of a socket, but there will usually be some device - specific information that also needs to be kept track of. The - 'priv' pointer in a struct pcmcia_device structure can be used to point to - a device-specific private data structure, like this. - - A driver needs to provide a dev_node_t structure for each device - on a card. In some cases, there is only one device per card (for - example, ethernet cards, modems). In other cases, there may be - many actual or logical devices (SCSI adapters, memory cards with - multiple partitions). The dev_node_t structures need to be kept - in a linked list starting at the 'dev' field of a struct pcmcia_device - structure. We allocate them in the card's private data structure, - because they generally can't be allocated dynamically. -*/ - -static const struct iw_handler_def netwave_handler_def; - -#define SIOCGIPSNAP SIOCIWFIRSTPRIV + 1 /* Site Survey Snapshot */ - -#define MAX_ESA 10 - -typedef struct net_addr { - u_char addr48[6]; -} net_addr; - -struct site_survey { - u_short length; - u_char struct_revision; - u_char roaming_state; - - u_char sp_existsFlag; - u_char sp_link_quality; - u_char sp_max_link_quality; - u_char linkQualityGoodFairBoundary; - u_char linkQualityFairPoorBoundary; - u_char sp_utilization; - u_char sp_goodness; - u_char sp_hotheadcount; - u_char roaming_condition; - - net_addr sp; - u_char numAPs; - net_addr nearByAccessPoints[MAX_ESA]; -}; - -typedef struct netwave_private { - struct pcmcia_device *p_dev; - spinlock_t spinlock; /* Serialize access to the hardware (SMP) */ - dev_node_t node; - u_char __iomem *ramBase; - int timeoutCounter; - int lastExec; - struct timer_list watchdog; /* To avoid blocking state */ - struct site_survey nss; - struct iw_statistics iw_stats; /* Wireless stats */ -} netwave_private; - -/* - * The Netwave card is little-endian, so won't work for big endian - * systems. - */ -static inline unsigned short get_uint16(u_char __iomem *staddr) -{ - return readw(staddr); /* Return only 16 bits */ -} - -static inline short get_int16(u_char __iomem * staddr) -{ - return readw(staddr); -} - -/* - * Wait until the WOC (Write Operation Complete) bit in the - * ASR (Adapter Status Register) is asserted. - * This should have aborted if it takes too long time. - */ -static inline void wait_WOC(unsigned int iobase) -{ - /* Spin lock */ - while ((inb(iobase + NETWAVE_REG_ASR) & 0x8) != 0x8) ; -} - -static void netwave_snapshot(netwave_private *priv, u_char __iomem *ramBase, - unsigned int iobase) { - u_short resultBuffer; - - /* if time since last snapshot is > 1 sec. (100 jiffies?) then take - * new snapshot, else return cached data. This is the recommended rate. - */ - if ( jiffies - priv->lastExec > 100) { - /* Take site survey snapshot */ - /*printk( KERN_DEBUG "Taking new snapshot. %ld\n", jiffies - - priv->lastExec); */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_SSS, ramBase + NETWAVE_EREG_CB + 0); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 1); - wait_WOC(iobase); - - /* Get result and copy to cach */ - resultBuffer = readw(ramBase + NETWAVE_EREG_CRBP); - copy_from_pc( &priv->nss, ramBase+resultBuffer, - sizeof(struct site_survey)); - } -} - -/* - * Function netwave_get_wireless_stats (dev) - * - * Wireless extensions statistics - * - */ -static struct iw_statistics *netwave_get_wireless_stats(struct net_device *dev) -{ - unsigned long flags; - unsigned int iobase = dev->base_addr; - netwave_private *priv = netdev_priv(dev); - u_char __iomem *ramBase = priv->ramBase; - struct iw_statistics* wstats; - - wstats = &priv->iw_stats; - - spin_lock_irqsave(&priv->spinlock, flags); - - netwave_snapshot( priv, ramBase, iobase); - - wstats->status = priv->nss.roaming_state; - wstats->qual.qual = readb( ramBase + NETWAVE_EREG_SPCQ); - wstats->qual.level = readb( ramBase + NETWAVE_EREG_ISPLQ); - wstats->qual.noise = readb( ramBase + NETWAVE_EREG_SPU) & 0x3f; - wstats->discard.nwid = 0L; - wstats->discard.code = 0L; - wstats->discard.misc = 0L; - - spin_unlock_irqrestore(&priv->spinlock, flags); - - return &priv->iw_stats; -} - -static const struct net_device_ops netwave_netdev_ops = { - .ndo_open = netwave_open, - .ndo_stop = netwave_close, - .ndo_start_xmit = netwave_start_xmit, - .ndo_set_multicast_list = set_multicast_list, - .ndo_tx_timeout = netwave_watchdog, - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -/* - * Function netwave_attach (void) - * - * Creates an "instance" of the driver, allocating local data - * structures for one device. The device is registered with Card - * Services. - * - * The dev_link structure is initialized, but we don't actually - * configure the card at this point -- we wait until we receive a - * card insertion event. - */ -static int netwave_probe(struct pcmcia_device *link) -{ - struct net_device *dev; - netwave_private *priv; - - DEBUG(0, "netwave_attach()\n"); - - /* Initialize the struct pcmcia_device structure */ - dev = alloc_etherdev(sizeof(netwave_private)); - if (!dev) - return -ENOMEM; - priv = netdev_priv(dev); - priv->p_dev = link; - link->priv = dev; - - /* The io structure describes IO port mapping */ - link->io.NumPorts1 = 16; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; - /* link->io.NumPorts2 = 16; - link->io.Attributes2 = IO_DATA_PATH_WIDTH_16; */ - link->io.IOAddrLines = 5; - - /* Interrupt setup */ - link->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING | IRQ_HANDLE_PRESENT; - link->irq.IRQInfo1 = IRQ_LEVEL_ID; - link->irq.Handler = &netwave_interrupt; - - /* General socket configuration */ - link->conf.Attributes = CONF_ENABLE_IRQ; - link->conf.IntType = INT_MEMORY_AND_IO; - link->conf.ConfigIndex = 1; - - /* Netwave private struct init. link/dev/node already taken care of, - * other stuff zero'd - Jean II */ - spin_lock_init(&priv->spinlock); - - /* Netwave specific entries in the device structure */ - dev->netdev_ops = &netwave_netdev_ops; - /* wireless extensions */ - dev->wireless_handlers = &netwave_handler_def; - - dev->watchdog_timeo = TX_TIMEOUT; - - link->irq.Instance = dev; - - return netwave_pcmcia_config( link); -} /* netwave_attach */ - -/* - * Function netwave_detach (link) - * - * This deletes a driver "instance". The device is de-registered - * with Card Services. If it has been released, all local data - * structures are freed. Otherwise, the structures will be freed - * when the device is released. - */ -static void netwave_detach(struct pcmcia_device *link) -{ - struct net_device *dev = link->priv; - - DEBUG(0, "netwave_detach(0x%p)\n", link); - - netwave_release(link); - - if (link->dev_node) - unregister_netdev(dev); - - free_netdev(dev); -} /* netwave_detach */ - -/* - * Wireless Handler : get protocol name - */ -static int netwave_get_name(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - strcpy(wrqu->name, "Netwave"); - return 0; -} - -/* - * Wireless Handler : set Network ID - */ -static int netwave_set_nwid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long flags; - unsigned int iobase = dev->base_addr; - netwave_private *priv = netdev_priv(dev); - u_char __iomem *ramBase = priv->ramBase; - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&priv->spinlock, flags); - - if(!wrqu->nwid.disabled) { - domain = wrqu->nwid.value; - printk( KERN_DEBUG "Setting domain to 0x%x%02x\n", - (domain >> 8) & 0x01, domain & 0xff); - wait_WOC(iobase); - writeb(NETWAVE_CMD_SMD, ramBase + NETWAVE_EREG_CB + 0); - writeb( domain & 0xff, ramBase + NETWAVE_EREG_CB + 1); - writeb((domain >>8 ) & 0x01,ramBase + NETWAVE_EREG_CB+2); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 3); - } - - /* ReEnable interrupts & restore flags */ - spin_unlock_irqrestore(&priv->spinlock, flags); - - return 0; -} - -/* - * Wireless Handler : get Network ID - */ -static int netwave_get_nwid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - wrqu->nwid.value = domain; - wrqu->nwid.disabled = 0; - wrqu->nwid.fixed = 1; - return 0; -} - -/* - * Wireless Handler : set scramble key - */ -static int netwave_set_scramble(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *key) -{ - unsigned long flags; - unsigned int iobase = dev->base_addr; - netwave_private *priv = netdev_priv(dev); - u_char __iomem *ramBase = priv->ramBase; - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&priv->spinlock, flags); - - scramble_key = (key[0] << 8) | key[1]; - wait_WOC(iobase); - writeb(NETWAVE_CMD_SSK, ramBase + NETWAVE_EREG_CB + 0); - writeb(scramble_key & 0xff, ramBase + NETWAVE_EREG_CB + 1); - writeb((scramble_key>>8) & 0xff, ramBase + NETWAVE_EREG_CB + 2); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 3); - - /* ReEnable interrupts & restore flags */ - spin_unlock_irqrestore(&priv->spinlock, flags); - - return 0; -} - -/* - * Wireless Handler : get scramble key - */ -static int netwave_get_scramble(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *key) -{ - key[1] = scramble_key & 0xff; - key[0] = (scramble_key>>8) & 0xff; - wrqu->encoding.flags = IW_ENCODE_ENABLED; - wrqu->encoding.length = 2; - return 0; -} - -/* - * Wireless Handler : get mode - */ -static int netwave_get_mode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - if(domain & 0x100) - wrqu->mode = IW_MODE_INFRA; - else - wrqu->mode = IW_MODE_ADHOC; - - return 0; -} - -/* - * Wireless Handler : get range info - */ -static int netwave_get_range(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - struct iw_range *range = (struct iw_range *) extra; - int ret = 0; - - /* Set the length (very important for backward compatibility) */ - wrqu->data.length = sizeof(struct iw_range); - - /* Set all the info we don't care or don't know about to zero */ - memset(range, 0, sizeof(struct iw_range)); - - /* Set the Wireless Extension versions */ - range->we_version_compiled = WIRELESS_EXT; - range->we_version_source = 9; /* Nothing for us in v10 and v11 */ - - /* Set information in the range struct */ - range->throughput = 450 * 1000; /* don't argue on this ! */ - range->min_nwid = 0x0000; - range->max_nwid = 0x01FF; - - range->num_channels = range->num_frequency = 0; - - range->sensitivity = 0x3F; - range->max_qual.qual = 255; - range->max_qual.level = 255; - range->max_qual.noise = 0; - - range->num_bitrates = 1; - range->bitrate[0] = 1000000; /* 1 Mb/s */ - - range->encoding_size[0] = 2; /* 16 bits scrambling */ - range->num_encoding_sizes = 1; - range->max_encoding_tokens = 1; /* Only one key possible */ - - return ret; -} - -/* - * Wireless Private Handler : get snapshot - */ -static int netwave_get_snap(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long flags; - unsigned int iobase = dev->base_addr; - netwave_private *priv = netdev_priv(dev); - u_char __iomem *ramBase = priv->ramBase; - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&priv->spinlock, flags); - - /* Take snapshot of environment */ - netwave_snapshot( priv, ramBase, iobase); - wrqu->data.length = priv->nss.length; - memcpy(extra, (u_char *) &priv->nss, sizeof( struct site_survey)); - - priv->lastExec = jiffies; - - /* ReEnable interrupts & restore flags */ - spin_unlock_irqrestore(&priv->spinlock, flags); - - return(0); -} - -/* - * Structures to export the Wireless Handlers - * This is the stuff that are treated the wireless extensions (iwconfig) - */ - -static const struct iw_priv_args netwave_private_args[] = { -/*{ cmd, set_args, get_args, name } */ - { SIOCGIPSNAP, 0, - IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | sizeof(struct site_survey), - "getsitesurvey" }, -}; - -static const iw_handler netwave_handler[] = -{ - NULL, /* SIOCSIWNAME */ - netwave_get_name, /* SIOCGIWNAME */ - netwave_set_nwid, /* SIOCSIWNWID */ - netwave_get_nwid, /* SIOCGIWNWID */ - NULL, /* SIOCSIWFREQ */ - NULL, /* SIOCGIWFREQ */ - NULL, /* SIOCSIWMODE */ - netwave_get_mode, /* SIOCGIWMODE */ - NULL, /* SIOCSIWSENS */ - NULL, /* SIOCGIWSENS */ - NULL, /* SIOCSIWRANGE */ - netwave_get_range, /* SIOCGIWRANGE */ - NULL, /* SIOCSIWPRIV */ - NULL, /* SIOCGIWPRIV */ - NULL, /* SIOCSIWSTATS */ - NULL, /* SIOCGIWSTATS */ - NULL, /* SIOCSIWSPY */ - NULL, /* SIOCGIWSPY */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWAP */ - NULL, /* SIOCGIWAP */ - NULL, /* -- hole -- */ - NULL, /* SIOCGIWAPLIST */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWESSID */ - NULL, /* SIOCGIWESSID */ - NULL, /* SIOCSIWNICKN */ - NULL, /* SIOCGIWNICKN */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWRATE */ - NULL, /* SIOCGIWRATE */ - NULL, /* SIOCSIWRTS */ - NULL, /* SIOCGIWRTS */ - NULL, /* SIOCSIWFRAG */ - NULL, /* SIOCGIWFRAG */ - NULL, /* SIOCSIWTXPOW */ - NULL, /* SIOCGIWTXPOW */ - NULL, /* SIOCSIWRETRY */ - NULL, /* SIOCGIWRETRY */ - netwave_set_scramble, /* SIOCSIWENCODE */ - netwave_get_scramble, /* SIOCGIWENCODE */ -}; - -static const iw_handler netwave_private_handler[] = -{ - NULL, /* SIOCIWFIRSTPRIV */ - netwave_get_snap, /* SIOCIWFIRSTPRIV + 1 */ -}; - -static const struct iw_handler_def netwave_handler_def = -{ - .num_standard = ARRAY_SIZE(netwave_handler), - .num_private = ARRAY_SIZE(netwave_private_handler), - .num_private_args = ARRAY_SIZE(netwave_private_args), - .standard = (iw_handler *) netwave_handler, - .private = (iw_handler *) netwave_private_handler, - .private_args = (struct iw_priv_args *) netwave_private_args, - .get_wireless_stats = netwave_get_wireless_stats, -}; - -/* - * Function netwave_pcmcia_config (link) - * - * netwave_pcmcia_config() is scheduled to run after a CARD_INSERTION - * event is received, to configure the PCMCIA socket, and to make the - * device available to the system. - * - */ - -#define CS_CHECK(fn, ret) \ -do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0) - -static int netwave_pcmcia_config(struct pcmcia_device *link) { - struct net_device *dev = link->priv; - netwave_private *priv = netdev_priv(dev); - int i, j, last_ret, last_fn; - win_req_t req; - memreq_t mem; - u_char __iomem *ramBase = NULL; - - DEBUG(0, "netwave_pcmcia_config(0x%p)\n", link); - - /* - * Try allocating IO ports. This tries a few fixed addresses. - * If you want, you can also read the card's config table to - * pick addresses -- see the serial driver for an example. - */ - for (i = j = 0x0; j < 0x400; j += 0x20) { - link->io.BasePort1 = j ^ 0x300; - i = pcmcia_request_io(link, &link->io); - if (i == 0) - break; - } - if (i != 0) { - cs_error(link, RequestIO, i); - goto failed; - } - - /* - * Now allocate an interrupt line. Note that this does not - * actually assign a handler to the interrupt. - */ - CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq)); - - /* - * This actually configures the PCMCIA socket -- setting up - * the I/O windows and the interrupt mapping. - */ - CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link, &link->conf)); - - /* - * Allocate a 32K memory window. Note that the struct pcmcia_device - * structure provides space for one window handle -- if your - * device needs several windows, you'll need to keep track of - * the handles in your private data structure, dev->priv. - */ - DEBUG(1, "Setting mem speed of %d\n", mem_speed); - - req.Attributes = WIN_DATA_WIDTH_8|WIN_MEMORY_TYPE_CM|WIN_ENABLE; - req.Base = 0; req.Size = 0x8000; - req.AccessSpeed = mem_speed; - CS_CHECK(RequestWindow, pcmcia_request_window(&link, &req, &link->win)); - mem.CardOffset = 0x20000; mem.Page = 0; - CS_CHECK(MapMemPage, pcmcia_map_mem_page(link->win, &mem)); - - /* Store base address of the common window frame */ - ramBase = ioremap(req.Base, 0x8000); - priv->ramBase = ramBase; - - dev->irq = link->irq.AssignedIRQ; - dev->base_addr = link->io.BasePort1; - SET_NETDEV_DEV(dev, &handle_to_dev(link)); - - if (register_netdev(dev) != 0) { - printk(KERN_DEBUG "netwave_cs: register_netdev() failed\n"); - goto failed; - } - - strcpy(priv->node.dev_name, dev->name); - link->dev_node = &priv->node; - - /* Reset card before reading physical address */ - netwave_doreset(dev->base_addr, ramBase); - - /* Read the ethernet address and fill in the Netwave registers. */ - for (i = 0; i < 6; i++) - dev->dev_addr[i] = readb(ramBase + NETWAVE_EREG_PA + i); - - printk(KERN_INFO "%s: Netwave: port %#3lx, irq %d, mem %lx, " - "id %c%c, hw_addr %pM\n", - dev->name, dev->base_addr, dev->irq, - (u_long) ramBase, - (int) readb(ramBase+NETWAVE_EREG_NI), - (int) readb(ramBase+NETWAVE_EREG_NI+1), - dev->dev_addr); - - /* get revision words */ - printk(KERN_DEBUG "Netwave_reset: revision %04x %04x\n", - get_uint16(ramBase + NETWAVE_EREG_ARW), - get_uint16(ramBase + NETWAVE_EREG_ARW+2)); - return 0; - -cs_failed: - cs_error(link, last_fn, last_ret); -failed: - netwave_release(link); - return -ENODEV; -} /* netwave_pcmcia_config */ - -/* - * Function netwave_release (arg) - * - * After a card is removed, netwave_release() will unregister the net - * device, and release the PCMCIA configuration. If the device is - * still open, this will be postponed until it is closed. - */ -static void netwave_release(struct pcmcia_device *link) -{ - struct net_device *dev = link->priv; - netwave_private *priv = netdev_priv(dev); - - DEBUG(0, "netwave_release(0x%p)\n", link); - - pcmcia_disable_device(link); - if (link->win) - iounmap(priv->ramBase); -} - -static int netwave_suspend(struct pcmcia_device *link) -{ - struct net_device *dev = link->priv; - - if (link->open) - netif_device_detach(dev); - - return 0; -} - -static int netwave_resume(struct pcmcia_device *link) -{ - struct net_device *dev = link->priv; - - if (link->open) { - netwave_reset(dev); - netif_device_attach(dev); - } - - return 0; -} - - -/* - * Function netwave_doreset (ioBase, ramBase) - * - * Proper hardware reset of the card. - */ -static void netwave_doreset(unsigned int ioBase, u_char __iomem *ramBase) -{ - /* Reset card */ - wait_WOC(ioBase); - outb(0x80, ioBase + NETWAVE_REG_PMR); - writeb(0x08, ramBase + NETWAVE_EREG_ASCC); /* Bit 3 is WOC */ - outb(0x0, ioBase + NETWAVE_REG_PMR); /* release reset */ -} - -/* - * Function netwave_reset (dev) - * - * Reset and restore all of the netwave registers - */ -static void netwave_reset(struct net_device *dev) { - /* u_char state; */ - netwave_private *priv = netdev_priv(dev); - u_char __iomem *ramBase = priv->ramBase; - unsigned int iobase = dev->base_addr; - - DEBUG(0, "netwave_reset: Done with hardware reset\n"); - - priv->timeoutCounter = 0; - - /* Reset card */ - netwave_doreset(iobase, ramBase); - printk(KERN_DEBUG "netwave_reset: Done with hardware reset\n"); - - /* Write a NOP to check the card */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_NOP, ramBase + NETWAVE_EREG_CB + 0); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 1); - - /* Set receive conf */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_SRC, ramBase + NETWAVE_EREG_CB + 0); - writeb(rxConfRxEna + rxConfBcast, ramBase + NETWAVE_EREG_CB + 1); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 2); - - /* Set transmit conf */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_STC, ramBase + NETWAVE_EREG_CB + 0); - writeb(txConfTxEna, ramBase + NETWAVE_EREG_CB + 1); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 2); - - /* Now set the MU Domain */ - printk(KERN_DEBUG "Setting domain to 0x%x%02x\n", (domain >> 8) & 0x01, domain & 0xff); - wait_WOC(iobase); - writeb(NETWAVE_CMD_SMD, ramBase + NETWAVE_EREG_CB + 0); - writeb(domain & 0xff, ramBase + NETWAVE_EREG_CB + 1); - writeb((domain>>8) & 0x01, ramBase + NETWAVE_EREG_CB + 2); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 3); - - /* Set scramble key */ - printk(KERN_DEBUG "Setting scramble key to 0x%x\n", scramble_key); - wait_WOC(iobase); - writeb(NETWAVE_CMD_SSK, ramBase + NETWAVE_EREG_CB + 0); - writeb(scramble_key & 0xff, ramBase + NETWAVE_EREG_CB + 1); - writeb((scramble_key>>8) & 0xff, ramBase + NETWAVE_EREG_CB + 2); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 3); - - /* Enable interrupts, bit 4 high to keep unused - * source from interrupting us, bit 2 high to - * set interrupt enable, 567 to enable TxDN, - * RxErr and RxRdy - */ - wait_WOC(iobase); - outb(imrConfIENA+imrConfRFU1, iobase + NETWAVE_REG_IMR); - - /* Hent 4 bytes fra 0x170. Skal vaere 0a,29,88,36 - * waitWOC - * skriv 80 til d000:3688 - * sjekk om det ble 80 - */ - - /* Enable Receiver */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_ER, ramBase + NETWAVE_EREG_CB + 0); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 1); - - /* Set the IENA bit in COR */ - wait_WOC(iobase); - outb(corConfIENA + corConfLVLREQ, iobase + NETWAVE_REG_COR); -} - -/* - * Function netwave_hw_xmit (data, len, dev) - */ -static int netwave_hw_xmit(unsigned char* data, int len, - struct net_device* dev) { - unsigned long flags; - unsigned int TxFreeList, - curBuff, - MaxData, - DataOffset; - int tmpcount; - - netwave_private *priv = netdev_priv(dev); - u_char __iomem * ramBase = priv->ramBase; - unsigned int iobase = dev->base_addr; - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&priv->spinlock, flags); - - /* Check if there are transmit buffers available */ - wait_WOC(iobase); - if ((inb(iobase+NETWAVE_REG_ASR) & NETWAVE_ASR_TXBA) == 0) { - /* No buffers available */ - printk(KERN_DEBUG "netwave_hw_xmit: %s - no xmit buffers available.\n", - dev->name); - spin_unlock_irqrestore(&priv->spinlock, flags); - return 1; - } - - dev->stats.tx_bytes += len; - - DEBUG(3, "Transmitting with SPCQ %x SPU %x LIF %x ISPLQ %x\n", - readb(ramBase + NETWAVE_EREG_SPCQ), - readb(ramBase + NETWAVE_EREG_SPU), - readb(ramBase + NETWAVE_EREG_LIF), - readb(ramBase + NETWAVE_EREG_ISPLQ)); - - /* Now try to insert it into the adapters free memory */ - wait_WOC(iobase); - TxFreeList = get_uint16(ramBase + NETWAVE_EREG_TDP); - MaxData = get_uint16(ramBase + NETWAVE_EREG_TDP+2); - DataOffset = get_uint16(ramBase + NETWAVE_EREG_TDP+4); - - DEBUG(3, "TxFreeList %x, MaxData %x, DataOffset %x\n", - TxFreeList, MaxData, DataOffset); - - /* Copy packet to the adapter fragment buffers */ - curBuff = TxFreeList; - tmpcount = 0; - while (tmpcount < len) { - int tmplen = len - tmpcount; - copy_to_pc(ramBase + curBuff + DataOffset, data + tmpcount, - (tmplen < MaxData) ? tmplen : MaxData); - tmpcount += MaxData; - - /* Advance to next buffer */ - curBuff = get_uint16(ramBase + curBuff); - } - - /* Now issue transmit list */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_TL, ramBase + NETWAVE_EREG_CB + 0); - writeb(len & 0xff, ramBase + NETWAVE_EREG_CB + 1); - writeb((len>>8) & 0xff, ramBase + NETWAVE_EREG_CB + 2); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 3); - - spin_unlock_irqrestore(&priv->spinlock, flags); - return 0; -} - -static netdev_tx_t netwave_start_xmit(struct sk_buff *skb, - struct net_device *dev) { - /* This flag indicate that the hardware can't perform a transmission. - * Theoritically, NET3 check it before sending a packet to the driver, - * but in fact it never do that and pool continuously. - * As the watchdog will abort too long transmissions, we are quite safe... - */ - - netif_stop_queue(dev); - - { - short length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN; - unsigned char* buf = skb->data; - - if (netwave_hw_xmit( buf, length, dev) == 1) { - /* Some error, let's make them call us another time? */ - netif_start_queue(dev); - } - dev->trans_start = jiffies; - } - dev_kfree_skb(skb); - - return NETDEV_TX_OK; -} /* netwave_start_xmit */ - -/* - * Function netwave_interrupt (irq, dev_id) - * - * This function is the interrupt handler for the Netwave card. This - * routine will be called whenever: - * 1. A packet is received. - * 2. A packet has successfully been transferred and the unit is - * ready to transmit another packet. - * 3. A command has completed execution. - */ -static irqreturn_t netwave_interrupt(int irq, void* dev_id) -{ - unsigned int iobase; - u_char __iomem *ramBase; - struct net_device *dev = (struct net_device *)dev_id; - struct netwave_private *priv = netdev_priv(dev); - struct pcmcia_device *link = priv->p_dev; - int i; - - if (!netif_device_present(dev)) - return IRQ_NONE; - - iobase = dev->base_addr; - ramBase = priv->ramBase; - - /* Now find what caused the interrupt, check while interrupts ready */ - for (i = 0; i < 10; i++) { - u_char status; - - wait_WOC(iobase); - if (!(inb(iobase+NETWAVE_REG_CCSR) & 0x02)) - break; /* None of the interrupt sources asserted (normal exit) */ - - status = inb(iobase + NETWAVE_REG_ASR); - - if (!pcmcia_dev_present(link)) { - DEBUG(1, "netwave_interrupt: Interrupt with status 0x%x " - "from removed or suspended card!\n", status); - break; - } - - /* RxRdy */ - if (status & 0x80) { - netwave_rx(dev); - /* wait_WOC(iobase); */ - /* RxRdy cannot be reset directly by the host */ - } - /* RxErr */ - if (status & 0x40) { - u_char rser; - - rser = readb(ramBase + NETWAVE_EREG_RSER); - - if (rser & 0x04) { - ++dev->stats.rx_dropped; - ++dev->stats.rx_crc_errors; - } - if (rser & 0x02) - ++dev->stats.rx_frame_errors; - - /* Clear the RxErr bit in RSER. RSER+4 is the - * write part. Also clear the RxCRC (0x04) and - * RxBig (0x02) bits if present */ - wait_WOC(iobase); - writeb(0x40 | (rser & 0x06), ramBase + NETWAVE_EREG_RSER + 4); - - /* Write bit 6 high to ASCC to clear RxErr in ASR, - * WOC must be set first! - */ - wait_WOC(iobase); - writeb(0x40, ramBase + NETWAVE_EREG_ASCC); - - /* Remember to count up dev->stats on error packets */ - ++dev->stats.rx_errors; - } - /* TxDN */ - if (status & 0x20) { - int txStatus; - - txStatus = readb(ramBase + NETWAVE_EREG_TSER); - DEBUG(3, "Transmit done. TSER = %x id %x\n", - txStatus, readb(ramBase + NETWAVE_EREG_TSER + 1)); - - if (txStatus & 0x20) { - /* Transmitting was okay, clear bits */ - wait_WOC(iobase); - writeb(0x2f, ramBase + NETWAVE_EREG_TSER + 4); - ++dev->stats.tx_packets; - } - - if (txStatus & 0xd0) { - if (txStatus & 0x80) { - ++dev->stats.collisions; /* Because of /proc/net/dev*/ - /* ++dev->stats.tx_aborted_errors; */ - /* printk("Collision. %ld\n", jiffies - dev->trans_start); */ - } - if (txStatus & 0x40) - ++dev->stats.tx_carrier_errors; - /* 0x80 TxGU Transmit giveup - nine times and no luck - * 0x40 TxNOAP No access point. Discarded packet. - * 0x10 TxErr Transmit error. Always set when - * TxGU and TxNOAP is set. (Those are the only ones - * to set TxErr). - */ - DEBUG(3, "netwave_interrupt: TxDN with error status %x\n", - txStatus); - - /* Clear out TxGU, TxNOAP, TxErr and TxTrys */ - wait_WOC(iobase); - writeb(0xdf & txStatus, ramBase+NETWAVE_EREG_TSER+4); - ++dev->stats.tx_errors; - } - DEBUG(3, "New status is TSER %x ASR %x\n", - readb(ramBase + NETWAVE_EREG_TSER), - inb(iobase + NETWAVE_REG_ASR)); - - netif_wake_queue(dev); - } - /* TxBA, this would trigger on all error packets received */ - /* if (status & 0x01) { - DEBUG(4, "Transmit buffers available, %x\n", status); - } - */ - } - /* Handled if we looped at least one time - Jean II */ - return IRQ_RETVAL(i); -} /* netwave_interrupt */ - -/* - * Function netwave_watchdog (a) - * - * Watchdog : when we start a transmission, we set a timer in the - * kernel. If the transmission complete, this timer is disabled. If - * it expire, we reset the card. - * - */ -static void netwave_watchdog(struct net_device *dev) { - - DEBUG(1, "%s: netwave_watchdog: watchdog timer expired\n", dev->name); - netwave_reset(dev); - dev->trans_start = jiffies; - netif_wake_queue(dev); -} /* netwave_watchdog */ - -static int netwave_rx(struct net_device *dev) -{ - netwave_private *priv = netdev_priv(dev); - u_char __iomem *ramBase = priv->ramBase; - unsigned int iobase = dev->base_addr; - u_char rxStatus; - struct sk_buff *skb = NULL; - unsigned int curBuffer, - rcvList; - int rcvLen; - int tmpcount = 0; - int dataCount, dataOffset; - int i; - u_char *ptr; - - DEBUG(3, "xinw_rx: Receiving ... \n"); - - /* Receive max 10 packets for now. */ - for (i = 0; i < 10; i++) { - /* Any packets? */ - wait_WOC(iobase); - rxStatus = readb(ramBase + NETWAVE_EREG_RSER); - if ( !( rxStatus & 0x80)) /* No more packets */ - break; - - /* Check if multicast/broadcast or other */ - /* multicast = (rxStatus & 0x20); */ - - /* The receive list pointer and length of the packet */ - wait_WOC(iobase); - rcvLen = get_int16( ramBase + NETWAVE_EREG_RDP); - rcvList = get_uint16( ramBase + NETWAVE_EREG_RDP + 2); - - if (rcvLen < 0) { - printk(KERN_DEBUG "netwave_rx: Receive packet with len %d\n", - rcvLen); - return 0; - } - - skb = dev_alloc_skb(rcvLen+5); - if (skb == NULL) { - DEBUG(1, "netwave_rx: Could not allocate an sk_buff of " - "length %d\n", rcvLen); - ++dev->stats.rx_dropped; - /* Tell the adapter to skip the packet */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_SRP, ramBase + NETWAVE_EREG_CB + 0); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 1); - return 0; - } - - skb_reserve( skb, 2); /* Align IP on 16 byte */ - skb_put( skb, rcvLen); - - /* Copy packet fragments to the skb data area */ - ptr = (u_char*) skb->data; - curBuffer = rcvList; - tmpcount = 0; - while ( tmpcount < rcvLen) { - /* Get length and offset of current buffer */ - dataCount = get_uint16( ramBase+curBuffer+2); - dataOffset = get_uint16( ramBase+curBuffer+4); - - copy_from_pc( ptr + tmpcount, - ramBase+curBuffer+dataOffset, dataCount); - - tmpcount += dataCount; - - /* Point to next buffer */ - curBuffer = get_uint16(ramBase + curBuffer); - } - - skb->protocol = eth_type_trans(skb,dev); - /* Queue packet for network layer */ - netif_rx(skb); - - dev->stats.rx_packets++; - dev->stats.rx_bytes += rcvLen; - - /* Got the packet, tell the adapter to skip it */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_SRP, ramBase + NETWAVE_EREG_CB + 0); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 1); - DEBUG(3, "Packet reception ok\n"); - } - return 0; -} - -static int netwave_open(struct net_device *dev) { - netwave_private *priv = netdev_priv(dev); - struct pcmcia_device *link = priv->p_dev; - - DEBUG(1, "netwave_open: starting.\n"); - - if (!pcmcia_dev_present(link)) - return -ENODEV; - - link->open++; - - netif_start_queue(dev); - netwave_reset(dev); - - return 0; -} - -static int netwave_close(struct net_device *dev) { - netwave_private *priv = netdev_priv(dev); - struct pcmcia_device *link = priv->p_dev; - - DEBUG(1, "netwave_close: finishing.\n"); - - link->open--; - netif_stop_queue(dev); - - return 0; -} - -static struct pcmcia_device_id netwave_ids[] = { - PCMCIA_DEVICE_PROD_ID12("Xircom", "CreditCard Netwave", 0x2e3ee845, 0x54e28a28), - PCMCIA_DEVICE_NULL, -}; -MODULE_DEVICE_TABLE(pcmcia, netwave_ids); - -static struct pcmcia_driver netwave_driver = { - .owner = THIS_MODULE, - .drv = { - .name = "netwave_cs", - }, - .probe = netwave_probe, - .remove = netwave_detach, - .id_table = netwave_ids, - .suspend = netwave_suspend, - .resume = netwave_resume, -}; - -static int __init init_netwave_cs(void) -{ - return pcmcia_register_driver(&netwave_driver); -} - -static void __exit exit_netwave_cs(void) -{ - pcmcia_unregister_driver(&netwave_driver); -} - -module_init(init_netwave_cs); -module_exit(exit_netwave_cs); - -/* Set or clear the multicast filter for this adaptor. - num_addrs == -1 Promiscuous mode, receive all packets - num_addrs == 0 Normal mode, clear multicast list - num_addrs > 0 Multicast mode, receive normal and MC packets, and do - best-effort filtering. - */ -static void set_multicast_list(struct net_device *dev) -{ - unsigned int iobase = dev->base_addr; - netwave_private *priv = netdev_priv(dev); - u_char __iomem * ramBase = priv->ramBase; - u_char rcvMode = 0; - -#ifdef PCMCIA_DEBUG - if (pc_debug > 2) { - static int old; - if (old != dev->mc_count) { - old = dev->mc_count; - DEBUG(0, "%s: setting Rx mode to %d addresses.\n", - dev->name, dev->mc_count); - } - } -#endif - - if (dev->mc_count || (dev->flags & IFF_ALLMULTI)) { - /* Multicast Mode */ - rcvMode = rxConfRxEna + rxConfAMP + rxConfBcast; - } else if (dev->flags & IFF_PROMISC) { - /* Promiscous mode */ - rcvMode = rxConfRxEna + rxConfPro + rxConfAMP + rxConfBcast; - } else { - /* Normal mode */ - rcvMode = rxConfRxEna + rxConfBcast; - } - - /* printk("netwave set_multicast_list: rcvMode to %x\n", rcvMode);*/ - /* Now set receive mode */ - wait_WOC(iobase); - writeb(NETWAVE_CMD_SRC, ramBase + NETWAVE_EREG_CB + 0); - writeb(rcvMode, ramBase + NETWAVE_EREG_CB + 1); - writeb(NETWAVE_CMD_EOC, ramBase + NETWAVE_EREG_CB + 2); -} -MODULE_LICENSE("GPL"); diff --git a/drivers/net/wireless/orinoco/Kconfig b/drivers/net/wireless/orinoco/Kconfig index dce6520..e2a2c18 100644 --- a/drivers/net/wireless/orinoco/Kconfig +++ b/drivers/net/wireless/orinoco/Kconfig @@ -1,6 +1,6 @@ config HERMES tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)" - depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211 + depends on (PPC_PMAC || PCI || PCMCIA) depends on CFG80211 && CFG80211_WEXT select WIRELESS_EXT select WEXT_SPY diff --git a/drivers/net/wireless/p54/Kconfig b/drivers/net/wireless/p54/Kconfig index b45d6a4..b0342a5 100644 --- a/drivers/net/wireless/p54/Kconfig +++ b/drivers/net/wireless/p54/Kconfig @@ -1,6 +1,6 @@ config P54_COMMON tristate "Softmac Prism54 support" - depends on MAC80211 && WLAN_80211 && EXPERIMENTAL + depends on MAC80211 && EXPERIMENTAL select FW_LOADER ---help--- This is common code for isl38xx/stlc45xx based modules. diff --git a/drivers/net/wireless/p54/eeprom.c b/drivers/net/wireless/p54/eeprom.c index 0efe67d..8e3818f 100644 --- a/drivers/net/wireless/p54/eeprom.c +++ b/drivers/net/wireless/p54/eeprom.c @@ -126,7 +126,7 @@ static int p54_generate_band(struct ieee80211_hw *dev, int ret = -ENOMEM; if ((!list->entries) || (!list->band_channel_num[band])) - return 0; + return -EINVAL; tmp = kzalloc(sizeof(*tmp), GFP_KERNEL); if (!tmp) @@ -158,6 +158,7 @@ static int p54_generate_band(struct ieee80211_hw *dev, (list->channels[i].data & CHAN_HAS_CURVE ? "" : " [curve data]"), list->channels[i].index, list->channels[i].freq); + continue; } tmp->channels[j].band = list->channels[i].band; @@ -165,7 +166,16 @@ static int p54_generate_band(struct ieee80211_hw *dev, j++; } - tmp->n_channels = list->band_channel_num[band]; + if (j == 0) { + printk(KERN_ERR "%s: Disabling totally damaged %s band.\n", + wiphy_name(dev->wiphy), (band == IEEE80211_BAND_2GHZ) ? + "2 GHz" : "5 GHz"); + + ret = -ENODATA; + goto err_out; + } + + tmp->n_channels = j; old = priv->band_table[band]; priv->band_table[band] = tmp; if (old) { @@ -228,13 +238,13 @@ static int p54_generate_channel_lists(struct ieee80211_hw *dev) struct p54_common *priv = dev->priv; struct p54_channel_list *list; unsigned int i, j, max_channel_num; - int ret = -ENOMEM; + int ret = 0; u16 freq; if ((priv->iq_autocal_len != priv->curve_data->entries) || (priv->iq_autocal_len != priv->output_limit->entries)) - printk(KERN_ERR "%s: EEPROM is damaged... you may not be able" - "to use all channels with this device.\n", + printk(KERN_ERR "%s: Unsupported or damaged EEPROM detected. " + "You may not be able to use all channels.\n", wiphy_name(dev->wiphy)); max_channel_num = max_t(unsigned int, priv->output_limit->entries, @@ -243,8 +253,10 @@ static int p54_generate_channel_lists(struct ieee80211_hw *dev) priv->curve_data->entries); list = kzalloc(sizeof(*list), GFP_KERNEL); - if (!list) + if (!list) { + ret = -ENOMEM; goto free; + } list->max_entries = max_channel_num; list->channels = kzalloc(sizeof(struct p54_channel_entry) * @@ -282,13 +294,8 @@ static int p54_generate_channel_lists(struct ieee80211_hw *dev) p54_compare_channels, NULL); for (i = 0, j = 0; i < IEEE80211_NUM_BANDS; i++) { - if (list->band_channel_num[i]) { - ret = p54_generate_band(dev, list, i); - if (ret) - goto free; - + if (p54_generate_band(dev, list, i) == 0) j++; - } } if (j == 0) { /* no useable band available. */ diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig index 390c0c7..bf60689 100644 --- a/drivers/net/wireless/rt2x00/Kconfig +++ b/drivers/net/wireless/rt2x00/Kconfig @@ -1,6 +1,6 @@ menuconfig RT2X00 tristate "Ralink driver support" - depends on MAC80211 && WLAN_80211 + depends on MAC80211 ---help--- This will enable the support for the Ralink drivers, developed in the rt2x00 project <http://rt2x00.serialmonkey.com>. @@ -64,8 +64,9 @@ config RT2800PCI_SOC default y config RT2800PCI - tristate "Ralink rt2800 (PCI/PCMCIA) support" + tristate "Ralink rt2800 (PCI/PCMCIA) support (VERY EXPERIMENTAL)" depends on (RT2800PCI_PCI || RT2800PCI_SOC) && EXPERIMENTAL + select RT2800_LIB select RT2X00_LIB_PCI if RT2800PCI_PCI select RT2X00_LIB_SOC if RT2800PCI_SOC select RT2X00_LIB_HT @@ -77,6 +78,9 @@ config RT2800PCI This adds support for rt2800 wireless chipset family. Supported chips: RT2760, RT2790, RT2860, RT2880, RT2890 & RT3052 + This driver is non-functional at the moment and is intended for + developers. + When compiled as a module, this driver will be called "rt2800pci.ko". config RT2500USB @@ -104,8 +108,9 @@ config RT73USB When compiled as a module, this driver will be called rt73usb. config RT2800USB - tristate "Ralink rt2800 (USB) support" + tristate "Ralink rt2800 (USB) support (EXPERIMENTAL)" depends on USB && EXPERIMENTAL + select RT2800_LIB select RT2X00_LIB_USB select RT2X00_LIB_HT select RT2X00_LIB_FIRMWARE @@ -115,8 +120,15 @@ config RT2800USB This adds experimental support for rt2800 wireless chipset family. Supported chips: RT2770, RT2870 & RT3070. + Known issues: + - support for RT2870 chips doesn't work with 802.11n APs yet + - support for RT3070 chips is non-functional at the moment + When compiled as a module, this driver will be called "rt2800usb.ko". +config RT2800_LIB + tristate + config RT2X00_LIB_PCI tristate select RT2X00_LIB diff --git a/drivers/net/wireless/rt2x00/Makefile b/drivers/net/wireless/rt2x00/Makefile index 912f5f6..9713398 100644 --- a/drivers/net/wireless/rt2x00/Makefile +++ b/drivers/net/wireless/rt2x00/Makefile @@ -13,6 +13,7 @@ obj-$(CONFIG_RT2X00_LIB) += rt2x00lib.o obj-$(CONFIG_RT2X00_LIB_PCI) += rt2x00pci.o obj-$(CONFIG_RT2X00_LIB_SOC) += rt2x00soc.o obj-$(CONFIG_RT2X00_LIB_USB) += rt2x00usb.o +obj-$(CONFIG_RT2800_LIB) += rt2800lib.o obj-$(CONFIG_RT2400PCI) += rt2400pci.o obj-$(CONFIG_RT2500PCI) += rt2500pci.o obj-$(CONFIG_RT61PCI) += rt61pci.o diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h new file mode 100644 index 0000000..d9b6a72 --- /dev/null +++ b/drivers/net/wireless/rt2x00/rt2800.h @@ -0,0 +1,1816 @@ +/* + Copyright (C) 2004 - 2009 rt2x00 SourceForge Project + <http://rt2x00.serialmonkey.com> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the + Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +/* + Module: rt2800 + Abstract: Data structures and registers for the rt2800 modules. + Supported chipsets: RT2800E, RT2800ED & RT2800U. + */ + +#ifndef RT2800_H +#define RT2800_H + +/* + * RF chip defines. + * + * RF2820 2.4G 2T3R + * RF2850 2.4G/5G 2T3R + * RF2720 2.4G 1T2R + * RF2750 2.4G/5G 1T2R + * RF3020 2.4G 1T1R + * RF2020 2.4G B/G + * RF3021 2.4G 1T2R + * RF3022 2.4G 2T2R + * RF3052 2.4G 2T2R + */ +#define RF2820 0x0001 +#define RF2850 0x0002 +#define RF2720 0x0003 +#define RF2750 0x0004 +#define RF3020 0x0005 +#define RF2020 0x0006 +#define RF3021 0x0007 +#define RF3022 0x0008 +#define RF3052 0x0009 + +/* + * Chipset version. + */ +#define RT2860C_VERSION 0x28600100 +#define RT2860D_VERSION 0x28600101 +#define RT2880E_VERSION 0x28720200 +#define RT2883_VERSION 0x28830300 +#define RT3070_VERSION 0x30700200 + +/* + * Signal information. + * Default offset is required for RSSI <-> dBm conversion. + */ +#define DEFAULT_RSSI_OFFSET 120 /* FIXME */ + +/* + * Register layout information. + */ +#define CSR_REG_BASE 0x1000 +#define CSR_REG_SIZE 0x0800 +#define EEPROM_BASE 0x0000 +#define EEPROM_SIZE 0x0110 +#define BBP_BASE 0x0000 +#define BBP_SIZE 0x0080 +#define RF_BASE 0x0004 +#define RF_SIZE 0x0010 + +/* + * Number of TX queues. + */ +#define NUM_TX_QUEUES 4 + +/* + * USB registers. + */ + +/* + * INT_SOURCE_CSR: Interrupt source register. + * Write one to clear corresponding bit. + * TX_FIFO_STATUS: FIFO Statistics is full, sw should read 0x171c + */ +#define INT_SOURCE_CSR 0x0200 +#define INT_SOURCE_CSR_RXDELAYINT FIELD32(0x00000001) +#define INT_SOURCE_CSR_TXDELAYINT FIELD32(0x00000002) +#define INT_SOURCE_CSR_RX_DONE FIELD32(0x00000004) +#define INT_SOURCE_CSR_AC0_DMA_DONE FIELD32(0x00000008) +#define INT_SOURCE_CSR_AC1_DMA_DONE FIELD32(0x00000010) +#define INT_SOURCE_CSR_AC2_DMA_DONE FIELD32(0x00000020) +#define INT_SOURCE_CSR_AC3_DMA_DONE FIELD32(0x00000040) +#define INT_SOURCE_CSR_HCCA_DMA_DONE FIELD32(0x00000080) +#define INT_SOURCE_CSR_MGMT_DMA_DONE FIELD32(0x00000100) +#define INT_SOURCE_CSR_MCU_COMMAND FIELD32(0x00000200) +#define INT_SOURCE_CSR_RXTX_COHERENT FIELD32(0x00000400) +#define INT_SOURCE_CSR_TBTT FIELD32(0x00000800) +#define INT_SOURCE_CSR_PRE_TBTT FIELD32(0x00001000) +#define INT_SOURCE_CSR_TX_FIFO_STATUS FIELD32(0x00002000) +#define INT_SOURCE_CSR_AUTO_WAKEUP FIELD32(0x00004000) +#define INT_SOURCE_CSR_GPTIMER FIELD32(0x00008000) +#define INT_SOURCE_CSR_RX_COHERENT FIELD32(0x00010000) +#define INT_SOURCE_CSR_TX_COHERENT FIELD32(0x00020000) + +/* + * INT_MASK_CSR: Interrupt MASK register. 1: the interrupt is mask OFF. + */ +#define INT_MASK_CSR 0x0204 +#define INT_MASK_CSR_RXDELAYINT FIELD32(0x00000001) +#define INT_MASK_CSR_TXDELAYINT FIELD32(0x00000002) +#define INT_MASK_CSR_RX_DONE FIELD32(0x00000004) +#define INT_MASK_CSR_AC0_DMA_DONE FIELD32(0x00000008) +#define INT_MASK_CSR_AC1_DMA_DONE FIELD32(0x00000010) +#define INT_MASK_CSR_AC2_DMA_DONE FIELD32(0x00000020) +#define INT_MASK_CSR_AC3_DMA_DONE FIELD32(0x00000040) +#define INT_MASK_CSR_HCCA_DMA_DONE FIELD32(0x00000080) +#define INT_MASK_CSR_MGMT_DMA_DONE FIELD32(0x00000100) +#define INT_MASK_CSR_MCU_COMMAND FIELD32(0x00000200) +#define INT_MASK_CSR_RXTX_COHERENT FIELD32(0x00000400) +#define INT_MASK_CSR_TBTT FIELD32(0x00000800) +#define INT_MASK_CSR_PRE_TBTT FIELD32(0x00001000) +#define INT_MASK_CSR_TX_FIFO_STATUS FIELD32(0x00002000) +#define INT_MASK_CSR_AUTO_WAKEUP FIELD32(0x00004000) +#define INT_MASK_CSR_GPTIMER FIELD32(0x00008000) +#define INT_MASK_CSR_RX_COHERENT FIELD32(0x00010000) +#define INT_MASK_CSR_TX_COHERENT FIELD32(0x00020000) + +/* + * WPDMA_GLO_CFG + */ +#define WPDMA_GLO_CFG 0x0208 +#define WPDMA_GLO_CFG_ENABLE_TX_DMA FIELD32(0x00000001) +#define WPDMA_GLO_CFG_TX_DMA_BUSY FIELD32(0x00000002) +#define WPDMA_GLO_CFG_ENABLE_RX_DMA FIELD32(0x00000004) +#define WPDMA_GLO_CFG_RX_DMA_BUSY FIELD32(0x00000008) +#define WPDMA_GLO_CFG_WP_DMA_BURST_SIZE FIELD32(0x00000030) +#define WPDMA_GLO_CFG_TX_WRITEBACK_DONE FIELD32(0x00000040) +#define WPDMA_GLO_CFG_BIG_ENDIAN FIELD32(0x00000080) +#define WPDMA_GLO_CFG_RX_HDR_SCATTER FIELD32(0x0000ff00) +#define WPDMA_GLO_CFG_HDR_SEG_LEN FIELD32(0xffff0000) + +/* + * WPDMA_RST_IDX + */ +#define WPDMA_RST_IDX 0x020c +#define WPDMA_RST_IDX_DTX_IDX0 FIELD32(0x00000001) +#define WPDMA_RST_IDX_DTX_IDX1 FIELD32(0x00000002) +#define WPDMA_RST_IDX_DTX_IDX2 FIELD32(0x00000004) +#define WPDMA_RST_IDX_DTX_IDX3 FIELD32(0x00000008) +#define WPDMA_RST_IDX_DTX_IDX4 FIELD32(0x00000010) +#define WPDMA_RST_IDX_DTX_IDX5 FIELD32(0x00000020) +#define WPDMA_RST_IDX_DRX_IDX0 FIELD32(0x00010000) + +/* + * DELAY_INT_CFG + */ +#define DELAY_INT_CFG 0x0210 +#define DELAY_INT_CFG_RXMAX_PTIME FIELD32(0x000000ff) +#define DELAY_INT_CFG_RXMAX_PINT FIELD32(0x00007f00) +#define DELAY_INT_CFG_RXDLY_INT_EN FIELD32(0x00008000) +#define DELAY_INT_CFG_TXMAX_PTIME FIELD32(0x00ff0000) +#define DELAY_INT_CFG_TXMAX_PINT FIELD32(0x7f000000) +#define DELAY_INT_CFG_TXDLY_INT_EN FIELD32(0x80000000) + +/* + * WMM_AIFSN_CFG: Aifsn for each EDCA AC + * AIFSN0: AC_BE + * AIFSN1: AC_BK + * AIFSN2: AC_VI + * AIFSN3: AC_VO + */ +#define WMM_AIFSN_CFG 0x0214 +#define WMM_AIFSN_CFG_AIFSN0 FIELD32(0x0000000f) +#define WMM_AIFSN_CFG_AIFSN1 FIELD32(0x000000f0) +#define WMM_AIFSN_CFG_AIFSN2 FIELD32(0x00000f00) +#define WMM_AIFSN_CFG_AIFSN3 FIELD32(0x0000f000) + +/* + * WMM_CWMIN_CSR: CWmin for each EDCA AC + * CWMIN0: AC_BE + * CWMIN1: AC_BK + * CWMIN2: AC_VI + * CWMIN3: AC_VO + */ +#define WMM_CWMIN_CFG 0x0218 +#define WMM_CWMIN_CFG_CWMIN0 FIELD32(0x0000000f) +#define WMM_CWMIN_CFG_CWMIN1 FIELD32(0x000000f0) +#define WMM_CWMIN_CFG_CWMIN2 FIELD32(0x00000f00) +#define WMM_CWMIN_CFG_CWMIN3 FIELD32(0x0000f000) + +/* + * WMM_CWMAX_CSR: CWmax for each EDCA AC + * CWMAX0: AC_BE + * CWMAX1: AC_BK + * CWMAX2: AC_VI + * CWMAX3: AC_VO + */ +#define WMM_CWMAX_CFG 0x021c +#define WMM_CWMAX_CFG_CWMAX0 FIELD32(0x0000000f) +#define WMM_CWMAX_CFG_CWMAX1 FIELD32(0x000000f0) +#define WMM_CWMAX_CFG_CWMAX2 FIELD32(0x00000f00) +#define WMM_CWMAX_CFG_CWMAX3 FIELD32(0x0000f000) + +/* + * AC_TXOP0: AC_BK/AC_BE TXOP register + * AC0TXOP: AC_BK in unit of 32us + * AC1TXOP: AC_BE in unit of 32us + */ +#define WMM_TXOP0_CFG 0x0220 +#define WMM_TXOP0_CFG_AC0TXOP FIELD32(0x0000ffff) +#define WMM_TXOP0_CFG_AC1TXOP FIELD32(0xffff0000) + +/* + * AC_TXOP1: AC_VO/AC_VI TXOP register + * AC2TXOP: AC_VI in unit of 32us + * AC3TXOP: AC_VO in unit of 32us + */ +#define WMM_TXOP1_CFG 0x0224 +#define WMM_TXOP1_CFG_AC2TXOP FIELD32(0x0000ffff) +#define WMM_TXOP1_CFG_AC3TXOP FIELD32(0xffff0000) + +/* + * GPIO_CTRL_CFG: + */ +#define GPIO_CTRL_CFG 0x0228 +#define GPIO_CTRL_CFG_BIT0 FIELD32(0x00000001) +#define GPIO_CTRL_CFG_BIT1 FIELD32(0x00000002) +#define GPIO_CTRL_CFG_BIT2 FIELD32(0x00000004) +#define GPIO_CTRL_CFG_BIT3 FIELD32(0x00000008) +#define GPIO_CTRL_CFG_BIT4 FIELD32(0x00000010) +#define GPIO_CTRL_CFG_BIT5 FIELD32(0x00000020) +#define GPIO_CTRL_CFG_BIT6 FIELD32(0x00000040) +#define GPIO_CTRL_CFG_BIT7 FIELD32(0x00000080) +#define GPIO_CTRL_CFG_BIT8 FIELD32(0x00000100) + +/* + * MCU_CMD_CFG + */ +#define MCU_CMD_CFG 0x022c + +/* + * AC_BK register offsets + */ +#define TX_BASE_PTR0 0x0230 +#define TX_MAX_CNT0 0x0234 +#define TX_CTX_IDX0 0x0238 +#define TX_DTX_IDX0 0x023c + +/* + * AC_BE register offsets + */ +#define TX_BASE_PTR1 0x0240 +#define TX_MAX_CNT1 0x0244 +#define TX_CTX_IDX1 0x0248 +#define TX_DTX_IDX1 0x024c + +/* + * AC_VI register offsets + */ +#define TX_BASE_PTR2 0x0250 +#define TX_MAX_CNT2 0x0254 +#define TX_CTX_IDX2 0x0258 +#define TX_DTX_IDX2 0x025c + +/* + * AC_VO register offsets + */ +#define TX_BASE_PTR3 0x0260 +#define TX_MAX_CNT3 0x0264 +#define TX_CTX_IDX3 0x0268 +#define TX_DTX_IDX3 0x026c + +/* + * HCCA register offsets + */ +#define TX_BASE_PTR4 0x0270 +#define TX_MAX_CNT4 0x0274 +#define TX_CTX_IDX4 0x0278 +#define TX_DTX_IDX4 0x027c + +/* + * MGMT register offsets + */ +#define TX_BASE_PTR5 0x0280 +#define TX_MAX_CNT5 0x0284 +#define TX_CTX_IDX5 0x0288 +#define TX_DTX_IDX5 0x028c + +/* + * RX register offsets + */ +#define RX_BASE_PTR 0x0290 +#define RX_MAX_CNT 0x0294 +#define RX_CRX_IDX 0x0298 +#define RX_DRX_IDX 0x029c + +/* + * PBF_SYS_CTRL + * HOST_RAM_WRITE: enable Host program ram write selection + */ +#define PBF_SYS_CTRL 0x0400 +#define PBF_SYS_CTRL_READY FIELD32(0x00000080) +#define PBF_SYS_CTRL_HOST_RAM_WRITE FIELD32(0x00010000) + +/* + * HOST-MCU shared memory + */ +#define HOST_CMD_CSR 0x0404 +#define HOST_CMD_CSR_HOST_COMMAND FIELD32(0x000000ff) + +/* + * PBF registers + * Most are for debug. Driver doesn't touch PBF register. + */ +#define PBF_CFG 0x0408 +#define PBF_MAX_PCNT 0x040c +#define PBF_CTRL 0x0410 +#define PBF_INT_STA 0x0414 +#define PBF_INT_ENA 0x0418 + +/* + * BCN_OFFSET0: + */ +#define BCN_OFFSET0 0x042c +#define BCN_OFFSET0_BCN0 FIELD32(0x000000ff) +#define BCN_OFFSET0_BCN1 FIELD32(0x0000ff00) +#define BCN_OFFSET0_BCN2 FIELD32(0x00ff0000) +#define BCN_OFFSET0_BCN3 FIELD32(0xff000000) + +/* + * BCN_OFFSET1: + */ +#define BCN_OFFSET1 0x0430 +#define BCN_OFFSET1_BCN4 FIELD32(0x000000ff) +#define BCN_OFFSET1_BCN5 FIELD32(0x0000ff00) +#define BCN_OFFSET1_BCN6 FIELD32(0x00ff0000) +#define BCN_OFFSET1_BCN7 FIELD32(0xff000000) + +/* + * PBF registers + * Most are for debug. Driver doesn't touch PBF register. + */ +#define TXRXQ_PCNT 0x0438 +#define PBF_DBG 0x043c + +/* + * RF registers + */ +#define RF_CSR_CFG 0x0500 +#define RF_CSR_CFG_DATA FIELD32(0x000000ff) +#define RF_CSR_CFG_REGNUM FIELD32(0x00001f00) +#define RF_CSR_CFG_WRITE FIELD32(0x00010000) +#define RF_CSR_CFG_BUSY FIELD32(0x00020000) + +/* + * MAC Control/Status Registers(CSR). + * Some values are set in TU, whereas 1 TU == 1024 us. + */ + +/* + * MAC_CSR0: ASIC revision number. + * ASIC_REV: 0 + * ASIC_VER: 2860 or 2870 + */ +#define MAC_CSR0 0x1000 +#define MAC_CSR0_ASIC_REV FIELD32(0x0000ffff) +#define MAC_CSR0_ASIC_VER FIELD32(0xffff0000) + +/* + * MAC_SYS_CTRL: + */ +#define MAC_SYS_CTRL 0x1004 +#define MAC_SYS_CTRL_RESET_CSR FIELD32(0x00000001) +#define MAC_SYS_CTRL_RESET_BBP FIELD32(0x00000002) +#define MAC_SYS_CTRL_ENABLE_TX FIELD32(0x00000004) +#define MAC_SYS_CTRL_ENABLE_RX FIELD32(0x00000008) +#define MAC_SYS_CTRL_CONTINUOUS_TX FIELD32(0x00000010) +#define MAC_SYS_CTRL_LOOPBACK FIELD32(0x00000020) +#define MAC_SYS_CTRL_WLAN_HALT FIELD32(0x00000040) +#define MAC_SYS_CTRL_RX_TIMESTAMP FIELD32(0x00000080) + +/* + * MAC_ADDR_DW0: STA MAC register 0 + */ +#define MAC_ADDR_DW0 0x1008 +#define MAC_ADDR_DW0_BYTE0 FIELD32(0x000000ff) +#define MAC_ADDR_DW0_BYTE1 FIELD32(0x0000ff00) +#define MAC_ADDR_DW0_BYTE2 FIELD32(0x00ff0000) +#define MAC_ADDR_DW0_BYTE3 FIELD32(0xff000000) + +/* + * MAC_ADDR_DW1: STA MAC register 1 + * UNICAST_TO_ME_MASK: + * Used to mask off bits from byte 5 of the MAC address + * to determine the UNICAST_TO_ME bit for RX frames. + * The full mask is complemented by BSS_ID_MASK: + * MASK = BSS_ID_MASK & UNICAST_TO_ME_MASK + */ +#define MAC_ADDR_DW1 0x100c +#define MAC_ADDR_DW1_BYTE4 FIELD32(0x000000ff) +#define MAC_ADDR_DW1_BYTE5 FIELD32(0x0000ff00) +#define MAC_ADDR_DW1_UNICAST_TO_ME_MASK FIELD32(0x00ff0000) + +/* + * MAC_BSSID_DW0: BSSID register 0 + */ +#define MAC_BSSID_DW0 0x1010 +#define MAC_BSSID_DW0_BYTE0 FIELD32(0x000000ff) +#define MAC_BSSID_DW0_BYTE1 FIELD32(0x0000ff00) +#define MAC_BSSID_DW0_BYTE2 FIELD32(0x00ff0000) +#define MAC_BSSID_DW0_BYTE3 FIELD32(0xff000000) + +/* + * MAC_BSSID_DW1: BSSID register 1 + * BSS_ID_MASK: + * 0: 1-BSSID mode (BSS index = 0) + * 1: 2-BSSID mode (BSS index: Byte5, bit 0) + * 2: 4-BSSID mode (BSS index: byte5, bit 0 - 1) + * 3: 8-BSSID mode (BSS index: byte5, bit 0 - 2) + * This mask is used to mask off bits 0, 1 and 2 of byte 5 of the + * BSSID. This will make sure that those bits will be ignored + * when determining the MY_BSS of RX frames. + */ +#define MAC_BSSID_DW1 0x1014 +#define MAC_BSSID_DW1_BYTE4 FIELD32(0x000000ff) +#define MAC_BSSID_DW1_BYTE5 FIELD32(0x0000ff00) +#define MAC_BSSID_DW1_BSS_ID_MASK FIELD32(0x00030000) +#define MAC_BSSID_DW1_BSS_BCN_NUM FIELD32(0x001c0000) + +/* + * MAX_LEN_CFG: Maximum frame length register. + * MAX_MPDU: rt2860b max 16k bytes + * MAX_PSDU: Maximum PSDU length + * (power factor) 0:2^13, 1:2^14, 2:2^15, 3:2^16 + */ +#define MAX_LEN_CFG 0x1018 +#define MAX_LEN_CFG_MAX_MPDU FIELD32(0x00000fff) +#define MAX_LEN_CFG_MAX_PSDU FIELD32(0x00003000) +#define MAX_LEN_CFG_MIN_PSDU FIELD32(0x0000c000) +#define MAX_LEN_CFG_MIN_MPDU FIELD32(0x000f0000) + +/* + * BBP_CSR_CFG: BBP serial control register + * VALUE: Register value to program into BBP + * REG_NUM: Selected BBP register + * READ_CONTROL: 0 write BBP, 1 read BBP + * BUSY: ASIC is busy executing BBP commands + * BBP_PAR_DUR: 0 4 MAC clocks, 1 8 MAC clocks + * BBP_RW_MODE: 0 serial, 1 paralell + */ +#define BBP_CSR_CFG 0x101c +#define BBP_CSR_CFG_VALUE FIELD32(0x000000ff) +#define BBP_CSR_CFG_REGNUM FIELD32(0x0000ff00) +#define BBP_CSR_CFG_READ_CONTROL FIELD32(0x00010000) +#define BBP_CSR_CFG_BUSY FIELD32(0x00020000) +#define BBP_CSR_CFG_BBP_PAR_DUR FIELD32(0x00040000) +#define BBP_CSR_CFG_BBP_RW_MODE FIELD32(0x00080000) + +/* + * RF_CSR_CFG0: RF control register + * REGID_AND_VALUE: Register value to program into RF + * BITWIDTH: Selected RF register + * STANDBYMODE: 0 high when standby, 1 low when standby + * SEL: 0 RF_LE0 activate, 1 RF_LE1 activate + * BUSY: ASIC is busy executing RF commands + */ +#define RF_CSR_CFG0 0x1020 +#define RF_CSR_CFG0_REGID_AND_VALUE FIELD32(0x00ffffff) +#define RF_CSR_CFG0_BITWIDTH FIELD32(0x1f000000) +#define RF_CSR_CFG0_REG_VALUE_BW FIELD32(0x1fffffff) +#define RF_CSR_CFG0_STANDBYMODE FIELD32(0x20000000) +#define RF_CSR_CFG0_SEL FIELD32(0x40000000) +#define RF_CSR_CFG0_BUSY FIELD32(0x80000000) + +/* + * RF_CSR_CFG1: RF control register + * REGID_AND_VALUE: Register value to program into RF + * RFGAP: Gap between BB_CONTROL_RF and RF_LE + * 0: 3 system clock cycle (37.5usec) + * 1: 5 system clock cycle (62.5usec) + */ +#define RF_CSR_CFG1 0x1024 +#define RF_CSR_CFG1_REGID_AND_VALUE FIELD32(0x00ffffff) +#define RF_CSR_CFG1_RFGAP FIELD32(0x1f000000) + +/* + * RF_CSR_CFG2: RF control register + * VALUE: Register value to program into RF + */ +#define RF_CSR_CFG2 0x1028 +#define RF_CSR_CFG2_VALUE FIELD32(0x00ffffff) + +/* + * LED_CFG: LED control + * color LED's: + * 0: off + * 1: blinking upon TX2 + * 2: periodic slow blinking + * 3: always on + * LED polarity: + * 0: active low + * 1: active high + */ +#define LED_CFG 0x102c +#define LED_CFG_ON_PERIOD FIELD32(0x000000ff) +#define LED_CFG_OFF_PERIOD FIELD32(0x0000ff00) +#define LED_CFG_SLOW_BLINK_PERIOD FIELD32(0x003f0000) +#define LED_CFG_R_LED_MODE FIELD32(0x03000000) +#define LED_CFG_G_LED_MODE FIELD32(0x0c000000) +#define LED_CFG_Y_LED_MODE FIELD32(0x30000000) +#define LED_CFG_LED_POLAR FIELD32(0x40000000) + +/* + * XIFS_TIME_CFG: MAC timing + * CCKM_SIFS_TIME: unit 1us. Applied after CCK RX/TX + * OFDM_SIFS_TIME: unit 1us. Applied after OFDM RX/TX + * OFDM_XIFS_TIME: unit 1us. Applied after OFDM RX + * when MAC doesn't reference BBP signal BBRXEND + * EIFS: unit 1us + * BB_RXEND_ENABLE: reference RXEND signal to begin XIFS defer + * + */ +#define XIFS_TIME_CFG 0x1100 +#define XIFS_TIME_CFG_CCKM_SIFS_TIME FIELD32(0x000000ff) +#define XIFS_TIME_CFG_OFDM_SIFS_TIME FIELD32(0x0000ff00) +#define XIFS_TIME_CFG_OFDM_XIFS_TIME FIELD32(0x000f0000) +#define XIFS_TIME_CFG_EIFS FIELD32(0x1ff00000) +#define XIFS_TIME_CFG_BB_RXEND_ENABLE FIELD32(0x20000000) + +/* + * BKOFF_SLOT_CFG: + */ +#define BKOFF_SLOT_CFG 0x1104 +#define BKOFF_SLOT_CFG_SLOT_TIME FIELD32(0x000000ff) +#define BKOFF_SLOT_CFG_CC_DELAY_TIME FIELD32(0x0000ff00) + +/* + * NAV_TIME_CFG: + */ +#define NAV_TIME_CFG 0x1108 +#define NAV_TIME_CFG_SIFS FIELD32(0x000000ff) +#define NAV_TIME_CFG_SLOT_TIME FIELD32(0x0000ff00) +#define NAV_TIME_CFG_EIFS FIELD32(0x01ff0000) +#define NAV_TIME_ZERO_SIFS FIELD32(0x02000000) + +/* + * CH_TIME_CFG: count as channel busy + */ +#define CH_TIME_CFG 0x110c + +/* + * PBF_LIFE_TIMER: TX/RX MPDU timestamp timer (free run) Unit: 1us + */ +#define PBF_LIFE_TIMER 0x1110 + +/* + * BCN_TIME_CFG: + * BEACON_INTERVAL: in unit of 1/16 TU + * TSF_TICKING: Enable TSF auto counting + * TSF_SYNC: Enable TSF sync, 00: disable, 01: infra mode, 10: ad-hoc mode + * BEACON_GEN: Enable beacon generator + */ +#define BCN_TIME_CFG 0x1114 +#define BCN_TIME_CFG_BEACON_INTERVAL FIELD32(0x0000ffff) +#define BCN_TIME_CFG_TSF_TICKING FIELD32(0x00010000) +#define BCN_TIME_CFG_TSF_SYNC FIELD32(0x00060000) +#define BCN_TIME_CFG_TBTT_ENABLE FIELD32(0x00080000) +#define BCN_TIME_CFG_BEACON_GEN FIELD32(0x00100000) +#define BCN_TIME_CFG_TX_TIME_COMPENSATE FIELD32(0xf0000000) + +/* + * TBTT_SYNC_CFG: + */ +#define TBTT_SYNC_CFG 0x1118 + +/* + * TSF_TIMER_DW0: Local lsb TSF timer, read-only + */ +#define TSF_TIMER_DW0 0x111c +#define TSF_TIMER_DW0_LOW_WORD FIELD32(0xffffffff) + +/* + * TSF_TIMER_DW1: Local msb TSF timer, read-only + */ +#define TSF_TIMER_DW1 0x1120 +#define TSF_TIMER_DW1_HIGH_WORD FIELD32(0xffffffff) + +/* + * TBTT_TIMER: TImer remains till next TBTT, read-only + */ +#define TBTT_TIMER 0x1124 + +/* + * INT_TIMER_CFG: + */ +#define INT_TIMER_CFG 0x1128 + +/* + * INT_TIMER_EN: GP-timer and pre-tbtt Int enable + */ +#define INT_TIMER_EN 0x112c + +/* + * CH_IDLE_STA: channel idle time + */ +#define CH_IDLE_STA 0x1130 + +/* + * CH_BUSY_STA: channel busy time + */ +#define CH_BUSY_STA 0x1134 + +/* + * MAC_STATUS_CFG: + * BBP_RF_BUSY: When set to 0, BBP and RF are stable. + * if 1 or higher one of the 2 registers is busy. + */ +#define MAC_STATUS_CFG 0x1200 +#define MAC_STATUS_CFG_BBP_RF_BUSY FIELD32(0x00000003) + +/* + * PWR_PIN_CFG: + */ +#define PWR_PIN_CFG 0x1204 + +/* + * AUTOWAKEUP_CFG: Manual power control / status register + * TBCN_BEFORE_WAKE: ForceWake has high privilege than PutToSleep when both set + * AUTOWAKE: 0:sleep, 1:awake + */ +#define AUTOWAKEUP_CFG 0x1208 +#define AUTOWAKEUP_CFG_AUTO_LEAD_TIME FIELD32(0x000000ff) +#define AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE FIELD32(0x00007f00) +#define AUTOWAKEUP_CFG_AUTOWAKE FIELD32(0x00008000) + +/* + * EDCA_AC0_CFG: + */ +#define EDCA_AC0_CFG 0x1300 +#define EDCA_AC0_CFG_TX_OP FIELD32(0x000000ff) +#define EDCA_AC0_CFG_AIFSN FIELD32(0x00000f00) +#define EDCA_AC0_CFG_CWMIN FIELD32(0x0000f000) +#define EDCA_AC0_CFG_CWMAX FIELD32(0x000f0000) + +/* + * EDCA_AC1_CFG: + */ +#define EDCA_AC1_CFG 0x1304 +#define EDCA_AC1_CFG_TX_OP FIELD32(0x000000ff) +#define EDCA_AC1_CFG_AIFSN FIELD32(0x00000f00) +#define EDCA_AC1_CFG_CWMIN FIELD32(0x0000f000) +#define EDCA_AC1_CFG_CWMAX FIELD32(0x000f0000) + +/* + * EDCA_AC2_CFG: + */ +#define EDCA_AC2_CFG 0x1308 +#define EDCA_AC2_CFG_TX_OP FIELD32(0x000000ff) +#define EDCA_AC2_CFG_AIFSN FIELD32(0x00000f00) +#define EDCA_AC2_CFG_CWMIN FIELD32(0x0000f000) +#define EDCA_AC2_CFG_CWMAX FIELD32(0x000f0000) + +/* + * EDCA_AC3_CFG: + */ +#define EDCA_AC3_CFG 0x130c +#define EDCA_AC3_CFG_TX_OP FIELD32(0x000000ff) +#define EDCA_AC3_CFG_AIFSN FIELD32(0x00000f00) +#define EDCA_AC3_CFG_CWMIN FIELD32(0x0000f000) +#define EDCA_AC3_CFG_CWMAX FIELD32(0x000f0000) + +/* + * EDCA_TID_AC_MAP: + */ +#define EDCA_TID_AC_MAP 0x1310 + +/* + * TX_PWR_CFG_0: + */ +#define TX_PWR_CFG_0 0x1314 +#define TX_PWR_CFG_0_1MBS FIELD32(0x0000000f) +#define TX_PWR_CFG_0_2MBS FIELD32(0x000000f0) +#define TX_PWR_CFG_0_55MBS FIELD32(0x00000f00) +#define TX_PWR_CFG_0_11MBS FIELD32(0x0000f000) +#define TX_PWR_CFG_0_6MBS FIELD32(0x000f0000) +#define TX_PWR_CFG_0_9MBS FIELD32(0x00f00000) +#define TX_PWR_CFG_0_12MBS FIELD32(0x0f000000) +#define TX_PWR_CFG_0_18MBS FIELD32(0xf0000000) + +/* + * TX_PWR_CFG_1: + */ +#define TX_PWR_CFG_1 0x1318 +#define TX_PWR_CFG_1_24MBS FIELD32(0x0000000f) +#define TX_PWR_CFG_1_36MBS FIELD32(0x000000f0) +#define TX_PWR_CFG_1_48MBS FIELD32(0x00000f00) +#define TX_PWR_CFG_1_54MBS FIELD32(0x0000f000) +#define TX_PWR_CFG_1_MCS0 FIELD32(0x000f0000) +#define TX_PWR_CFG_1_MCS1 FIELD32(0x00f00000) +#define TX_PWR_CFG_1_MCS2 FIELD32(0x0f000000) +#define TX_PWR_CFG_1_MCS3 FIELD32(0xf0000000) + +/* + * TX_PWR_CFG_2: + */ +#define TX_PWR_CFG_2 0x131c +#define TX_PWR_CFG_2_MCS4 FIELD32(0x0000000f) +#define TX_PWR_CFG_2_MCS5 FIELD32(0x000000f0) +#define TX_PWR_CFG_2_MCS6 FIELD32(0x00000f00) +#define TX_PWR_CFG_2_MCS7 FIELD32(0x0000f000) +#define TX_PWR_CFG_2_MCS8 FIELD32(0x000f0000) +#define TX_PWR_CFG_2_MCS9 FIELD32(0x00f00000) +#define TX_PWR_CFG_2_MCS10 FIELD32(0x0f000000) +#define TX_PWR_CFG_2_MCS11 FIELD32(0xf0000000) + +/* + * TX_PWR_CFG_3: + */ +#define TX_PWR_CFG_3 0x1320 +#define TX_PWR_CFG_3_MCS12 FIELD32(0x0000000f) +#define TX_PWR_CFG_3_MCS13 FIELD32(0x000000f0) +#define TX_PWR_CFG_3_MCS14 FIELD32(0x00000f00) +#define TX_PWR_CFG_3_MCS15 FIELD32(0x0000f000) +#define TX_PWR_CFG_3_UKNOWN1 FIELD32(0x000f0000) +#define TX_PWR_CFG_3_UKNOWN2 FIELD32(0x00f00000) +#define TX_PWR_CFG_3_UKNOWN3 FIELD32(0x0f000000) +#define TX_PWR_CFG_3_UKNOWN4 FIELD32(0xf0000000) + +/* + * TX_PWR_CFG_4: + */ +#define TX_PWR_CFG_4 0x1324 +#define TX_PWR_CFG_4_UKNOWN5 FIELD32(0x0000000f) +#define TX_PWR_CFG_4_UKNOWN6 FIELD32(0x000000f0) +#define TX_PWR_CFG_4_UKNOWN7 FIELD32(0x00000f00) +#define TX_PWR_CFG_4_UKNOWN8 FIELD32(0x0000f000) + +/* + * TX_PIN_CFG: + */ +#define TX_PIN_CFG 0x1328 +#define TX_PIN_CFG_PA_PE_A0_EN FIELD32(0x00000001) +#define TX_PIN_CFG_PA_PE_G0_EN FIELD32(0x00000002) +#define TX_PIN_CFG_PA_PE_A1_EN FIELD32(0x00000004) +#define TX_PIN_CFG_PA_PE_G1_EN FIELD32(0x00000008) +#define TX_PIN_CFG_PA_PE_A0_POL FIELD32(0x00000010) +#define TX_PIN_CFG_PA_PE_G0_POL FIELD32(0x00000020) +#define TX_PIN_CFG_PA_PE_A1_POL FIELD32(0x00000040) +#define TX_PIN_CFG_PA_PE_G1_POL FIELD32(0x00000080) +#define TX_PIN_CFG_LNA_PE_A0_EN FIELD32(0x00000100) +#define TX_PIN_CFG_LNA_PE_G0_EN FIELD32(0x00000200) +#define TX_PIN_CFG_LNA_PE_A1_EN FIELD32(0x00000400) +#define TX_PIN_CFG_LNA_PE_G1_EN FIELD32(0x00000800) +#define TX_PIN_CFG_LNA_PE_A0_POL FIELD32(0x00001000) +#define TX_PIN_CFG_LNA_PE_G0_POL FIELD32(0x00002000) +#define TX_PIN_CFG_LNA_PE_A1_POL FIELD32(0x00004000) +#define TX_PIN_CFG_LNA_PE_G1_POL FIELD32(0x00008000) +#define TX_PIN_CFG_RFTR_EN FIELD32(0x00010000) +#define TX_PIN_CFG_RFTR_POL FIELD32(0x00020000) +#define TX_PIN_CFG_TRSW_EN FIELD32(0x00040000) +#define TX_PIN_CFG_TRSW_POL FIELD32(0x00080000) + +/* + * TX_BAND_CFG: 0x1 use upper 20MHz, 0x0 use lower 20MHz + */ +#define TX_BAND_CFG 0x132c +#define TX_BAND_CFG_HT40_PLUS FIELD32(0x00000001) +#define TX_BAND_CFG_A FIELD32(0x00000002) +#define TX_BAND_CFG_BG FIELD32(0x00000004) + +/* + * TX_SW_CFG0: + */ +#define TX_SW_CFG0 0x1330 + +/* + * TX_SW_CFG1: + */ +#define TX_SW_CFG1 0x1334 + +/* + * TX_SW_CFG2: + */ +#define TX_SW_CFG2 0x1338 + +/* + * TXOP_THRES_CFG: + */ +#define TXOP_THRES_CFG 0x133c + +/* + * TXOP_CTRL_CFG: + */ +#define TXOP_CTRL_CFG 0x1340 + +/* + * TX_RTS_CFG: + * RTS_THRES: unit:byte + * RTS_FBK_EN: enable rts rate fallback + */ +#define TX_RTS_CFG 0x1344 +#define TX_RTS_CFG_AUTO_RTS_RETRY_LIMIT FIELD32(0x000000ff) +#define TX_RTS_CFG_RTS_THRES FIELD32(0x00ffff00) +#define TX_RTS_CFG_RTS_FBK_EN FIELD32(0x01000000) + +/* + * TX_TIMEOUT_CFG: + * MPDU_LIFETIME: expiration time = 2^(9+MPDU LIFE TIME) us + * RX_ACK_TIMEOUT: unit:slot. Used for TX procedure + * TX_OP_TIMEOUT: TXOP timeout value for TXOP truncation. + * it is recommended that: + * (SLOT_TIME) > (TX_OP_TIMEOUT) > (RX_ACK_TIMEOUT) + */ +#define TX_TIMEOUT_CFG 0x1348 +#define TX_TIMEOUT_CFG_MPDU_LIFETIME FIELD32(0x000000f0) +#define TX_TIMEOUT_CFG_RX_ACK_TIMEOUT FIELD32(0x0000ff00) +#define TX_TIMEOUT_CFG_TX_OP_TIMEOUT FIELD32(0x00ff0000) + +/* + * TX_RTY_CFG: + * SHORT_RTY_LIMIT: short retry limit + * LONG_RTY_LIMIT: long retry limit + * LONG_RTY_THRE: Long retry threshoold + * NON_AGG_RTY_MODE: Non-Aggregate MPDU retry mode + * 0:expired by retry limit, 1: expired by mpdu life timer + * AGG_RTY_MODE: Aggregate MPDU retry mode + * 0:expired by retry limit, 1: expired by mpdu life timer + * TX_AUTO_FB_ENABLE: Tx retry PHY rate auto fallback enable + */ +#define TX_RTY_CFG 0x134c +#define TX_RTY_CFG_SHORT_RTY_LIMIT FIELD32(0x000000ff) +#define TX_RTY_CFG_LONG_RTY_LIMIT FIELD32(0x0000ff00) +#define TX_RTY_CFG_LONG_RTY_THRE FIELD32(0x0fff0000) +#define TX_RTY_CFG_NON_AGG_RTY_MODE FIELD32(0x10000000) +#define TX_RTY_CFG_AGG_RTY_MODE FIELD32(0x20000000) +#define TX_RTY_CFG_TX_AUTO_FB_ENABLE FIELD32(0x40000000) + +/* + * TX_LINK_CFG: + * REMOTE_MFB_LIFETIME: remote MFB life time. unit: 32us + * MFB_ENABLE: TX apply remote MFB 1:enable + * REMOTE_UMFS_ENABLE: remote unsolicit MFB enable + * 0: not apply remote remote unsolicit (MFS=7) + * TX_MRQ_EN: MCS request TX enable + * TX_RDG_EN: RDG TX enable + * TX_CF_ACK_EN: Piggyback CF-ACK enable + * REMOTE_MFB: remote MCS feedback + * REMOTE_MFS: remote MCS feedback sequence number + */ +#define TX_LINK_CFG 0x1350 +#define TX_LINK_CFG_REMOTE_MFB_LIFETIME FIELD32(0x000000ff) +#define TX_LINK_CFG_MFB_ENABLE FIELD32(0x00000100) +#define TX_LINK_CFG_REMOTE_UMFS_ENABLE FIELD32(0x00000200) +#define TX_LINK_CFG_TX_MRQ_EN FIELD32(0x00000400) +#define TX_LINK_CFG_TX_RDG_EN FIELD32(0x00000800) +#define TX_LINK_CFG_TX_CF_ACK_EN FIELD32(0x00001000) +#define TX_LINK_CFG_REMOTE_MFB FIELD32(0x00ff0000) +#define TX_LINK_CFG_REMOTE_MFS FIELD32(0xff000000) + +/* + * HT_FBK_CFG0: + */ +#define HT_FBK_CFG0 0x1354 +#define HT_FBK_CFG0_HTMCS0FBK FIELD32(0x0000000f) +#define HT_FBK_CFG0_HTMCS1FBK FIELD32(0x000000f0) +#define HT_FBK_CFG0_HTMCS2FBK FIELD32(0x00000f00) +#define HT_FBK_CFG0_HTMCS3FBK FIELD32(0x0000f000) +#define HT_FBK_CFG0_HTMCS4FBK FIELD32(0x000f0000) +#define HT_FBK_CFG0_HTMCS5FBK FIELD32(0x00f00000) +#define HT_FBK_CFG0_HTMCS6FBK FIELD32(0x0f000000) +#define HT_FBK_CFG0_HTMCS7FBK FIELD32(0xf0000000) + +/* + * HT_FBK_CFG1: + */ +#define HT_FBK_CFG1 0x1358 +#define HT_FBK_CFG1_HTMCS8FBK FIELD32(0x0000000f) +#define HT_FBK_CFG1_HTMCS9FBK FIELD32(0x000000f0) +#define HT_FBK_CFG1_HTMCS10FBK FIELD32(0x00000f00) +#define HT_FBK_CFG1_HTMCS11FBK FIELD32(0x0000f000) +#define HT_FBK_CFG1_HTMCS12FBK FIELD32(0x000f0000) +#define HT_FBK_CFG1_HTMCS13FBK FIELD32(0x00f00000) +#define HT_FBK_CFG1_HTMCS14FBK FIELD32(0x0f000000) +#define HT_FBK_CFG1_HTMCS15FBK FIELD32(0xf0000000) + +/* + * LG_FBK_CFG0: + */ +#define LG_FBK_CFG0 0x135c +#define LG_FBK_CFG0_OFDMMCS0FBK FIELD32(0x0000000f) +#define LG_FBK_CFG0_OFDMMCS1FBK FIELD32(0x000000f0) +#define LG_FBK_CFG0_OFDMMCS2FBK FIELD32(0x00000f00) +#define LG_FBK_CFG0_OFDMMCS3FBK FIELD32(0x0000f000) +#define LG_FBK_CFG0_OFDMMCS4FBK FIELD32(0x000f0000) +#define LG_FBK_CFG0_OFDMMCS5FBK FIELD32(0x00f00000) +#define LG_FBK_CFG0_OFDMMCS6FBK FIELD32(0x0f000000) +#define LG_FBK_CFG0_OFDMMCS7FBK FIELD32(0xf0000000) + +/* + * LG_FBK_CFG1: + */ +#define LG_FBK_CFG1 0x1360 +#define LG_FBK_CFG0_CCKMCS0FBK FIELD32(0x0000000f) +#define LG_FBK_CFG0_CCKMCS1FBK FIELD32(0x000000f0) +#define LG_FBK_CFG0_CCKMCS2FBK FIELD32(0x00000f00) +#define LG_FBK_CFG0_CCKMCS3FBK FIELD32(0x0000f000) + +/* + * CCK_PROT_CFG: CCK Protection + * PROTECT_RATE: Protection control frame rate for CCK TX(RTS/CTS/CFEnd) + * PROTECT_CTRL: Protection control frame type for CCK TX + * 0:none, 1:RTS/CTS, 2:CTS-to-self + * PROTECT_NAV: TXOP protection type for CCK TX + * 0:none, 1:ShortNAVprotect, 2:LongNAVProtect + * TX_OP_ALLOW_CCK: CCK TXOP allowance, 0:disallow + * TX_OP_ALLOW_OFDM: CCK TXOP allowance, 0:disallow + * TX_OP_ALLOW_MM20: CCK TXOP allowance, 0:disallow + * TX_OP_ALLOW_MM40: CCK TXOP allowance, 0:disallow + * TX_OP_ALLOW_GF20: CCK TXOP allowance, 0:disallow + * TX_OP_ALLOW_GF40: CCK TXOP allowance, 0:disallow + * RTS_TH_EN: RTS threshold enable on CCK TX + */ +#define CCK_PROT_CFG 0x1364 +#define CCK_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) +#define CCK_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) +#define CCK_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) +#define CCK_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) +#define CCK_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) +#define CCK_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) +#define CCK_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) +#define CCK_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) +#define CCK_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) +#define CCK_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) + +/* + * OFDM_PROT_CFG: OFDM Protection + */ +#define OFDM_PROT_CFG 0x1368 +#define OFDM_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) +#define OFDM_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) +#define OFDM_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) +#define OFDM_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) +#define OFDM_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) +#define OFDM_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) +#define OFDM_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) +#define OFDM_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) +#define OFDM_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) +#define OFDM_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) + +/* + * MM20_PROT_CFG: MM20 Protection + */ +#define MM20_PROT_CFG 0x136c +#define MM20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) +#define MM20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) +#define MM20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) +#define MM20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) +#define MM20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) +#define MM20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) +#define MM20_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) +#define MM20_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) +#define MM20_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) +#define MM20_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) + +/* + * MM40_PROT_CFG: MM40 Protection + */ +#define MM40_PROT_CFG 0x1370 +#define MM40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) +#define MM40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) +#define MM40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) +#define MM40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) +#define MM40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) +#define MM40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) +#define MM40_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) +#define MM40_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) +#define MM40_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) +#define MM40_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) + +/* + * GF20_PROT_CFG: GF20 Protection + */ +#define GF20_PROT_CFG 0x1374 +#define GF20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) +#define GF20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) +#define GF20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) +#define GF20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) +#define GF20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) +#define GF20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) +#define GF20_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) +#define GF20_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) +#define GF20_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) +#define GF20_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) + +/* + * GF40_PROT_CFG: GF40 Protection + */ +#define GF40_PROT_CFG 0x1378 +#define GF40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) +#define GF40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) +#define GF40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) +#define GF40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) +#define GF40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) +#define GF40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) +#define GF40_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) +#define GF40_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) +#define GF40_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) +#define GF40_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) + +/* + * EXP_CTS_TIME: + */ +#define EXP_CTS_TIME 0x137c + +/* + * EXP_ACK_TIME: + */ +#define EXP_ACK_TIME 0x1380 + +/* + * RX_FILTER_CFG: RX configuration register. + */ +#define RX_FILTER_CFG 0x1400 +#define RX_FILTER_CFG_DROP_CRC_ERROR FIELD32(0x00000001) +#define RX_FILTER_CFG_DROP_PHY_ERROR FIELD32(0x00000002) +#define RX_FILTER_CFG_DROP_NOT_TO_ME FIELD32(0x00000004) +#define RX_FILTER_CFG_DROP_NOT_MY_BSSD FIELD32(0x00000008) +#define RX_FILTER_CFG_DROP_VER_ERROR FIELD32(0x00000010) +#define RX_FILTER_CFG_DROP_MULTICAST FIELD32(0x00000020) +#define RX_FILTER_CFG_DROP_BROADCAST FIELD32(0x00000040) +#define RX_FILTER_CFG_DROP_DUPLICATE FIELD32(0x00000080) +#define RX_FILTER_CFG_DROP_CF_END_ACK FIELD32(0x00000100) +#define RX_FILTER_CFG_DROP_CF_END FIELD32(0x00000200) +#define RX_FILTER_CFG_DROP_ACK FIELD32(0x00000400) +#define RX_FILTER_CFG_DROP_CTS FIELD32(0x00000800) +#define RX_FILTER_CFG_DROP_RTS FIELD32(0x00001000) +#define RX_FILTER_CFG_DROP_PSPOLL FIELD32(0x00002000) +#define RX_FILTER_CFG_DROP_BA FIELD32(0x00004000) +#define RX_FILTER_CFG_DROP_BAR FIELD32(0x00008000) +#define RX_FILTER_CFG_DROP_CNTL FIELD32(0x00010000) + +/* + * AUTO_RSP_CFG: + * AUTORESPONDER: 0: disable, 1: enable + * BAC_ACK_POLICY: 0:long, 1:short preamble + * CTS_40_MMODE: Response CTS 40MHz duplicate mode + * CTS_40_MREF: Response CTS 40MHz duplicate mode + * AR_PREAMBLE: Auto responder preamble 0:long, 1:short preamble + * DUAL_CTS_EN: Power bit value in control frame + * ACK_CTS_PSM_BIT:Power bit value in control frame + */ +#define AUTO_RSP_CFG 0x1404 +#define AUTO_RSP_CFG_AUTORESPONDER FIELD32(0x00000001) +#define AUTO_RSP_CFG_BAC_ACK_POLICY FIELD32(0x00000002) +#define AUTO_RSP_CFG_CTS_40_MMODE FIELD32(0x00000004) +#define AUTO_RSP_CFG_CTS_40_MREF FIELD32(0x00000008) +#define AUTO_RSP_CFG_AR_PREAMBLE FIELD32(0x00000010) +#define AUTO_RSP_CFG_DUAL_CTS_EN FIELD32(0x00000040) +#define AUTO_RSP_CFG_ACK_CTS_PSM_BIT FIELD32(0x00000080) + +/* + * LEGACY_BASIC_RATE: + */ +#define LEGACY_BASIC_RATE 0x1408 + +/* + * HT_BASIC_RATE: + */ +#define HT_BASIC_RATE 0x140c + +/* + * HT_CTRL_CFG: + */ +#define HT_CTRL_CFG 0x1410 + +/* + * SIFS_COST_CFG: + */ +#define SIFS_COST_CFG 0x1414 + +/* + * RX_PARSER_CFG: + * Set NAV for all received frames + */ +#define RX_PARSER_CFG 0x1418 + +/* + * TX_SEC_CNT0: + */ +#define TX_SEC_CNT0 0x1500 + +/* + * RX_SEC_CNT0: + */ +#define RX_SEC_CNT0 0x1504 + +/* + * CCMP_FC_MUTE: + */ +#define CCMP_FC_MUTE 0x1508 + +/* + * TXOP_HLDR_ADDR0: + */ +#define TXOP_HLDR_ADDR0 0x1600 + +/* + * TXOP_HLDR_ADDR1: + */ +#define TXOP_HLDR_ADDR1 0x1604 + +/* + * TXOP_HLDR_ET: + */ +#define TXOP_HLDR_ET 0x1608 + +/* + * QOS_CFPOLL_RA_DW0: + */ +#define QOS_CFPOLL_RA_DW0 0x160c + +/* + * QOS_CFPOLL_RA_DW1: + */ +#define QOS_CFPOLL_RA_DW1 0x1610 + +/* + * QOS_CFPOLL_QC: + */ +#define QOS_CFPOLL_QC 0x1614 + +/* + * RX_STA_CNT0: RX PLCP error count & RX CRC error count + */ +#define RX_STA_CNT0 0x1700 +#define RX_STA_CNT0_CRC_ERR FIELD32(0x0000ffff) +#define RX_STA_CNT0_PHY_ERR FIELD32(0xffff0000) + +/* + * RX_STA_CNT1: RX False CCA count & RX LONG frame count + */ +#define RX_STA_CNT1 0x1704 +#define RX_STA_CNT1_FALSE_CCA FIELD32(0x0000ffff) +#define RX_STA_CNT1_PLCP_ERR FIELD32(0xffff0000) + +/* + * RX_STA_CNT2: + */ +#define RX_STA_CNT2 0x1708 +#define RX_STA_CNT2_RX_DUPLI_COUNT FIELD32(0x0000ffff) +#define RX_STA_CNT2_RX_FIFO_OVERFLOW FIELD32(0xffff0000) + +/* + * TX_STA_CNT0: TX Beacon count + */ +#define TX_STA_CNT0 0x170c +#define TX_STA_CNT0_TX_FAIL_COUNT FIELD32(0x0000ffff) +#define TX_STA_CNT0_TX_BEACON_COUNT FIELD32(0xffff0000) + +/* + * TX_STA_CNT1: TX tx count + */ +#define TX_STA_CNT1 0x1710 +#define TX_STA_CNT1_TX_SUCCESS FIELD32(0x0000ffff) +#define TX_STA_CNT1_TX_RETRANSMIT FIELD32(0xffff0000) + +/* + * TX_STA_CNT2: TX tx count + */ +#define TX_STA_CNT2 0x1714 +#define TX_STA_CNT2_TX_ZERO_LEN_COUNT FIELD32(0x0000ffff) +#define TX_STA_CNT2_TX_UNDER_FLOW_COUNT FIELD32(0xffff0000) + +/* + * TX_STA_FIFO: TX Result for specific PID status fifo register + */ +#define TX_STA_FIFO 0x1718 +#define TX_STA_FIFO_VALID FIELD32(0x00000001) +#define TX_STA_FIFO_PID_TYPE FIELD32(0x0000001e) +#define TX_STA_FIFO_TX_SUCCESS FIELD32(0x00000020) +#define TX_STA_FIFO_TX_AGGRE FIELD32(0x00000040) +#define TX_STA_FIFO_TX_ACK_REQUIRED FIELD32(0x00000080) +#define TX_STA_FIFO_WCID FIELD32(0x0000ff00) +#define TX_STA_FIFO_SUCCESS_RATE FIELD32(0xffff0000) +#define TX_STA_FIFO_MCS FIELD32(0x007f0000) +#define TX_STA_FIFO_PHYMODE FIELD32(0xc0000000) + +/* + * TX_AGG_CNT: Debug counter + */ +#define TX_AGG_CNT 0x171c +#define TX_AGG_CNT_NON_AGG_TX_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT_AGG_TX_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT0: + */ +#define TX_AGG_CNT0 0x1720 +#define TX_AGG_CNT0_AGG_SIZE_1_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT0_AGG_SIZE_2_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT1: + */ +#define TX_AGG_CNT1 0x1724 +#define TX_AGG_CNT1_AGG_SIZE_3_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT1_AGG_SIZE_4_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT2: + */ +#define TX_AGG_CNT2 0x1728 +#define TX_AGG_CNT2_AGG_SIZE_5_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT2_AGG_SIZE_6_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT3: + */ +#define TX_AGG_CNT3 0x172c +#define TX_AGG_CNT3_AGG_SIZE_7_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT3_AGG_SIZE_8_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT4: + */ +#define TX_AGG_CNT4 0x1730 +#define TX_AGG_CNT4_AGG_SIZE_9_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT4_AGG_SIZE_10_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT5: + */ +#define TX_AGG_CNT5 0x1734 +#define TX_AGG_CNT5_AGG_SIZE_11_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT5_AGG_SIZE_12_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT6: + */ +#define TX_AGG_CNT6 0x1738 +#define TX_AGG_CNT6_AGG_SIZE_13_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT6_AGG_SIZE_14_COUNT FIELD32(0xffff0000) + +/* + * TX_AGG_CNT7: + */ +#define TX_AGG_CNT7 0x173c +#define TX_AGG_CNT7_AGG_SIZE_15_COUNT FIELD32(0x0000ffff) +#define TX_AGG_CNT7_AGG_SIZE_16_COUNT FIELD32(0xffff0000) + +/* + * MPDU_DENSITY_CNT: + * TX_ZERO_DEL: TX zero length delimiter count + * RX_ZERO_DEL: RX zero length delimiter count + */ +#define MPDU_DENSITY_CNT 0x1740 +#define MPDU_DENSITY_CNT_TX_ZERO_DEL FIELD32(0x0000ffff) +#define MPDU_DENSITY_CNT_RX_ZERO_DEL FIELD32(0xffff0000) + +/* + * Security key table memory. + * MAC_WCID_BASE: 8-bytes (use only 6 bytes) * 256 entry + * PAIRWISE_KEY_TABLE_BASE: 32-byte * 256 entry + * MAC_IVEIV_TABLE_BASE: 8-byte * 256-entry + * MAC_WCID_ATTRIBUTE_BASE: 4-byte * 256-entry + * SHARED_KEY_TABLE_BASE: 32-byte * 16-entry + * SHARED_KEY_MODE_BASE: 4-byte * 16-entry + */ +#define MAC_WCID_BASE 0x1800 +#define PAIRWISE_KEY_TABLE_BASE 0x4000 +#define MAC_IVEIV_TABLE_BASE 0x6000 +#define MAC_WCID_ATTRIBUTE_BASE 0x6800 +#define SHARED_KEY_TABLE_BASE 0x6c00 +#define SHARED_KEY_MODE_BASE 0x7000 + +#define MAC_WCID_ENTRY(__idx) \ + ( MAC_WCID_BASE + ((__idx) * sizeof(struct mac_wcid_entry)) ) +#define PAIRWISE_KEY_ENTRY(__idx) \ + ( PAIRWISE_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) ) +#define MAC_IVEIV_ENTRY(__idx) \ + ( MAC_IVEIV_TABLE_BASE + ((__idx) & sizeof(struct mac_iveiv_entry)) ) +#define MAC_WCID_ATTR_ENTRY(__idx) \ + ( MAC_WCID_ATTRIBUTE_BASE + ((__idx) * sizeof(u32)) ) +#define SHARED_KEY_ENTRY(__idx) \ + ( SHARED_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) ) +#define SHARED_KEY_MODE_ENTRY(__idx) \ + ( SHARED_KEY_MODE_BASE + ((__idx) * sizeof(u32)) ) + +struct mac_wcid_entry { + u8 mac[6]; + u8 reserved[2]; +} __attribute__ ((packed)); + +struct hw_key_entry { + u8 key[16]; + u8 tx_mic[8]; + u8 rx_mic[8]; +} __attribute__ ((packed)); + +struct mac_iveiv_entry { + u8 iv[8]; +} __attribute__ ((packed)); + +/* + * MAC_WCID_ATTRIBUTE: + */ +#define MAC_WCID_ATTRIBUTE_KEYTAB FIELD32(0x00000001) +#define MAC_WCID_ATTRIBUTE_CIPHER FIELD32(0x0000000e) +#define MAC_WCID_ATTRIBUTE_BSS_IDX FIELD32(0x00000070) +#define MAC_WCID_ATTRIBUTE_RX_WIUDF FIELD32(0x00000380) + +/* + * SHARED_KEY_MODE: + */ +#define SHARED_KEY_MODE_BSS0_KEY0 FIELD32(0x00000007) +#define SHARED_KEY_MODE_BSS0_KEY1 FIELD32(0x00000070) +#define SHARED_KEY_MODE_BSS0_KEY2 FIELD32(0x00000700) +#define SHARED_KEY_MODE_BSS0_KEY3 FIELD32(0x00007000) +#define SHARED_KEY_MODE_BSS1_KEY0 FIELD32(0x00070000) +#define SHARED_KEY_MODE_BSS1_KEY1 FIELD32(0x00700000) +#define SHARED_KEY_MODE_BSS1_KEY2 FIELD32(0x07000000) +#define SHARED_KEY_MODE_BSS1_KEY3 FIELD32(0x70000000) + +/* + * HOST-MCU communication + */ + +/* + * H2M_MAILBOX_CSR: Host-to-MCU Mailbox. + */ +#define H2M_MAILBOX_CSR 0x7010 +#define H2M_MAILBOX_CSR_ARG0 FIELD32(0x000000ff) +#define H2M_MAILBOX_CSR_ARG1 FIELD32(0x0000ff00) +#define H2M_MAILBOX_CSR_CMD_TOKEN FIELD32(0x00ff0000) +#define H2M_MAILBOX_CSR_OWNER FIELD32(0xff000000) + +/* + * H2M_MAILBOX_CID: + */ +#define H2M_MAILBOX_CID 0x7014 +#define H2M_MAILBOX_CID_CMD0 FIELD32(0x000000ff) +#define H2M_MAILBOX_CID_CMD1 FIELD32(0x0000ff00) +#define H2M_MAILBOX_CID_CMD2 FIELD32(0x00ff0000) +#define H2M_MAILBOX_CID_CMD3 FIELD32(0xff000000) + +/* + * H2M_MAILBOX_STATUS: + */ +#define H2M_MAILBOX_STATUS 0x701c + +/* + * H2M_INT_SRC: + */ +#define H2M_INT_SRC 0x7024 + +/* + * H2M_BBP_AGENT: + */ +#define H2M_BBP_AGENT 0x7028 + +/* + * MCU_LEDCS: LED control for MCU Mailbox. + */ +#define MCU_LEDCS_LED_MODE FIELD8(0x1f) +#define MCU_LEDCS_POLARITY FIELD8(0x01) + +/* + * HW_CS_CTS_BASE: + * Carrier-sense CTS frame base address. + * It's where mac stores carrier-sense frame for carrier-sense function. + */ +#define HW_CS_CTS_BASE 0x7700 + +/* + * HW_DFS_CTS_BASE: + * DFS CTS frame base address. It's where mac stores CTS frame for DFS. + */ +#define HW_DFS_CTS_BASE 0x7780 + +/* + * TXRX control registers - base address 0x3000 + */ + +/* + * TXRX_CSR1: + * rt2860b UNKNOWN reg use R/O Reg Addr 0x77d0 first.. + */ +#define TXRX_CSR1 0x77d0 + +/* + * HW_DEBUG_SETTING_BASE: + * since NULL frame won't be that long (256 byte) + * We steal 16 tail bytes to save debugging settings + */ +#define HW_DEBUG_SETTING_BASE 0x77f0 +#define HW_DEBUG_SETTING_BASE2 0x7770 + +/* + * HW_BEACON_BASE + * In order to support maximum 8 MBSS and its maximum length + * is 512 bytes for each beacon + * Three section discontinue memory segments will be used. + * 1. The original region for BCN 0~3 + * 2. Extract memory from FCE table for BCN 4~5 + * 3. Extract memory from Pair-wise key table for BCN 6~7 + * It occupied those memory of wcid 238~253 for BCN 6 + * and wcid 222~237 for BCN 7 + * + * IMPORTANT NOTE: Not sure why legacy driver does this, + * but HW_BEACON_BASE7 is 0x0200 bytes below HW_BEACON_BASE6. + */ +#define HW_BEACON_BASE0 0x7800 +#define HW_BEACON_BASE1 0x7a00 +#define HW_BEACON_BASE2 0x7c00 +#define HW_BEACON_BASE3 0x7e00 +#define HW_BEACON_BASE4 0x7200 +#define HW_BEACON_BASE5 0x7400 +#define HW_BEACON_BASE6 0x5dc0 +#define HW_BEACON_BASE7 0x5bc0 + +#define HW_BEACON_OFFSET(__index) \ + ( ((__index) < 4) ? ( HW_BEACON_BASE0 + (__index * 0x0200) ) : \ + (((__index) < 6) ? ( HW_BEACON_BASE4 + ((__index - 4) * 0x0200) ) : \ + (HW_BEACON_BASE6 - ((__index - 6) * 0x0200))) ) + +/* + * BBP registers. + * The wordsize of the BBP is 8 bits. + */ + +/* + * BBP 1: TX Antenna + */ +#define BBP1_TX_POWER FIELD8(0x07) +#define BBP1_TX_ANTENNA FIELD8(0x18) + +/* + * BBP 3: RX Antenna + */ +#define BBP3_RX_ANTENNA FIELD8(0x18) +#define BBP3_HT40_PLUS FIELD8(0x20) + +/* + * BBP 4: Bandwidth + */ +#define BBP4_TX_BF FIELD8(0x01) +#define BBP4_BANDWIDTH FIELD8(0x18) + +/* + * RFCSR registers + * The wordsize of the RFCSR is 8 bits. + */ + +/* + * RFCSR 6: + */ +#define RFCSR6_R FIELD8(0x03) + +/* + * RFCSR 7: + */ +#define RFCSR7_RF_TUNING FIELD8(0x01) + +/* + * RFCSR 12: + */ +#define RFCSR12_TX_POWER FIELD8(0x1f) + +/* + * RFCSR 22: + */ +#define RFCSR22_BASEBAND_LOOPBACK FIELD8(0x01) + +/* + * RFCSR 23: + */ +#define RFCSR23_FREQ_OFFSET FIELD8(0x7f) + +/* + * RFCSR 30: + */ +#define RFCSR30_RF_CALIBRATION FIELD8(0x80) + +/* + * RF registers + */ + +/* + * RF 2 + */ +#define RF2_ANTENNA_RX2 FIELD32(0x00000040) +#define RF2_ANTENNA_TX1 FIELD32(0x00004000) +#define RF2_ANTENNA_RX1 FIELD32(0x00020000) + +/* + * RF 3 + */ +#define RF3_TXPOWER_G FIELD32(0x00003e00) +#define RF3_TXPOWER_A_7DBM_BOOST FIELD32(0x00000200) +#define RF3_TXPOWER_A FIELD32(0x00003c00) + +/* + * RF 4 + */ +#define RF4_TXPOWER_G FIELD32(0x000007c0) +#define RF4_TXPOWER_A_7DBM_BOOST FIELD32(0x00000040) +#define RF4_TXPOWER_A FIELD32(0x00000780) +#define RF4_FREQ_OFFSET FIELD32(0x001f8000) +#define RF4_HT40 FIELD32(0x00200000) + +/* + * EEPROM content. + * The wordsize of the EEPROM is 16 bits. + */ + +/* + * EEPROM Version + */ +#define EEPROM_VERSION 0x0001 +#define EEPROM_VERSION_FAE FIELD16(0x00ff) +#define EEPROM_VERSION_VERSION FIELD16(0xff00) + +/* + * HW MAC address. + */ +#define EEPROM_MAC_ADDR_0 0x0002 +#define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) +#define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) +#define EEPROM_MAC_ADDR_1 0x0003 +#define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) +#define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) +#define EEPROM_MAC_ADDR_2 0x0004 +#define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) +#define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) + +/* + * EEPROM ANTENNA config + * RXPATH: 1: 1R, 2: 2R, 3: 3R + * TXPATH: 1: 1T, 2: 2T + */ +#define EEPROM_ANTENNA 0x001a +#define EEPROM_ANTENNA_RXPATH FIELD16(0x000f) +#define EEPROM_ANTENNA_TXPATH FIELD16(0x00f0) +#define EEPROM_ANTENNA_RF_TYPE FIELD16(0x0f00) + +/* + * EEPROM NIC config + * CARDBUS_ACCEL: 0 - enable, 1 - disable + */ +#define EEPROM_NIC 0x001b +#define EEPROM_NIC_HW_RADIO FIELD16(0x0001) +#define EEPROM_NIC_DYNAMIC_TX_AGC FIELD16(0x0002) +#define EEPROM_NIC_EXTERNAL_LNA_BG FIELD16(0x0004) +#define EEPROM_NIC_EXTERNAL_LNA_A FIELD16(0x0008) +#define EEPROM_NIC_CARDBUS_ACCEL FIELD16(0x0010) +#define EEPROM_NIC_BW40M_SB_BG FIELD16(0x0020) +#define EEPROM_NIC_BW40M_SB_A FIELD16(0x0040) +#define EEPROM_NIC_WPS_PBC FIELD16(0x0080) +#define EEPROM_NIC_BW40M_BG FIELD16(0x0100) +#define EEPROM_NIC_BW40M_A FIELD16(0x0200) + +/* + * EEPROM frequency + */ +#define EEPROM_FREQ 0x001d +#define EEPROM_FREQ_OFFSET FIELD16(0x00ff) +#define EEPROM_FREQ_LED_MODE FIELD16(0x7f00) +#define EEPROM_FREQ_LED_POLARITY FIELD16(0x1000) + +/* + * EEPROM LED + * POLARITY_RDY_G: Polarity RDY_G setting. + * POLARITY_RDY_A: Polarity RDY_A setting. + * POLARITY_ACT: Polarity ACT setting. + * POLARITY_GPIO_0: Polarity GPIO0 setting. + * POLARITY_GPIO_1: Polarity GPIO1 setting. + * POLARITY_GPIO_2: Polarity GPIO2 setting. + * POLARITY_GPIO_3: Polarity GPIO3 setting. + * POLARITY_GPIO_4: Polarity GPIO4 setting. + * LED_MODE: Led mode. + */ +#define EEPROM_LED1 0x001e +#define EEPROM_LED2 0x001f +#define EEPROM_LED3 0x0020 +#define EEPROM_LED_POLARITY_RDY_BG FIELD16(0x0001) +#define EEPROM_LED_POLARITY_RDY_A FIELD16(0x0002) +#define EEPROM_LED_POLARITY_ACT FIELD16(0x0004) +#define EEPROM_LED_POLARITY_GPIO_0 FIELD16(0x0008) +#define EEPROM_LED_POLARITY_GPIO_1 FIELD16(0x0010) +#define EEPROM_LED_POLARITY_GPIO_2 FIELD16(0x0020) +#define EEPROM_LED_POLARITY_GPIO_3 FIELD16(0x0040) +#define EEPROM_LED_POLARITY_GPIO_4 FIELD16(0x0080) +#define EEPROM_LED_LED_MODE FIELD16(0x1f00) + +/* + * EEPROM LNA + */ +#define EEPROM_LNA 0x0022 +#define EEPROM_LNA_BG FIELD16(0x00ff) +#define EEPROM_LNA_A0 FIELD16(0xff00) + +/* + * EEPROM RSSI BG offset + */ +#define EEPROM_RSSI_BG 0x0023 +#define EEPROM_RSSI_BG_OFFSET0 FIELD16(0x00ff) +#define EEPROM_RSSI_BG_OFFSET1 FIELD16(0xff00) + +/* + * EEPROM RSSI BG2 offset + */ +#define EEPROM_RSSI_BG2 0x0024 +#define EEPROM_RSSI_BG2_OFFSET2 FIELD16(0x00ff) +#define EEPROM_RSSI_BG2_LNA_A1 FIELD16(0xff00) + +/* + * EEPROM RSSI A offset + */ +#define EEPROM_RSSI_A 0x0025 +#define EEPROM_RSSI_A_OFFSET0 FIELD16(0x00ff) +#define EEPROM_RSSI_A_OFFSET1 FIELD16(0xff00) + +/* + * EEPROM RSSI A2 offset + */ +#define EEPROM_RSSI_A2 0x0026 +#define EEPROM_RSSI_A2_OFFSET2 FIELD16(0x00ff) +#define EEPROM_RSSI_A2_LNA_A2 FIELD16(0xff00) + +/* + * EEPROM TXpower delta: 20MHZ AND 40 MHZ use different power. + * This is delta in 40MHZ. + * VALUE: Tx Power dalta value (MAX=4) + * TYPE: 1: Plus the delta value, 0: minus the delta value + * TXPOWER: Enable: + */ +#define EEPROM_TXPOWER_DELTA 0x0028 +#define EEPROM_TXPOWER_DELTA_VALUE FIELD16(0x003f) +#define EEPROM_TXPOWER_DELTA_TYPE FIELD16(0x0040) +#define EEPROM_TXPOWER_DELTA_TXPOWER FIELD16(0x0080) + +/* + * EEPROM TXPOWER 802.11BG + */ +#define EEPROM_TXPOWER_BG1 0x0029 +#define EEPROM_TXPOWER_BG2 0x0030 +#define EEPROM_TXPOWER_BG_SIZE 7 +#define EEPROM_TXPOWER_BG_1 FIELD16(0x00ff) +#define EEPROM_TXPOWER_BG_2 FIELD16(0xff00) + +/* + * EEPROM TXPOWER 802.11A + */ +#define EEPROM_TXPOWER_A1 0x003c +#define EEPROM_TXPOWER_A2 0x0053 +#define EEPROM_TXPOWER_A_SIZE 6 +#define EEPROM_TXPOWER_A_1 FIELD16(0x00ff) +#define EEPROM_TXPOWER_A_2 FIELD16(0xff00) + +/* + * EEPROM TXpower byrate: 20MHZ power + */ +#define EEPROM_TXPOWER_BYRATE 0x006f + +/* + * EEPROM BBP. + */ +#define EEPROM_BBP_START 0x0078 +#define EEPROM_BBP_SIZE 16 +#define EEPROM_BBP_VALUE FIELD16(0x00ff) +#define EEPROM_BBP_REG_ID FIELD16(0xff00) + +/* + * MCU mailbox commands. + */ +#define MCU_SLEEP 0x30 +#define MCU_WAKEUP 0x31 +#define MCU_RADIO_OFF 0x35 +#define MCU_CURRENT 0x36 +#define MCU_LED 0x50 +#define MCU_LED_STRENGTH 0x51 +#define MCU_LED_1 0x52 +#define MCU_LED_2 0x53 +#define MCU_LED_3 0x54 +#define MCU_RADAR 0x60 +#define MCU_BOOT_SIGNAL 0x72 +#define MCU_BBP_SIGNAL 0x80 +#define MCU_POWER_SAVE 0x83 + +/* + * MCU mailbox tokens + */ +#define TOKEN_WAKUP 3 + +/* + * DMA descriptor defines. + */ +#define TXWI_DESC_SIZE ( 4 * sizeof(__le32) ) +#define RXWI_DESC_SIZE ( 4 * sizeof(__le32) ) + +/* + * TX WI structure + */ + +/* + * Word0 + * FRAG: 1 To inform TKIP engine this is a fragment. + * MIMO_PS: The remote peer is in dynamic MIMO-PS mode + * TX_OP: 0:HT TXOP rule , 1:PIFS TX ,2:Backoff, 3:sifs + * BW: Channel bandwidth 20MHz or 40 MHz + * STBC: 1: STBC support MCS =0-7, 2,3 : RESERVED + */ +#define TXWI_W0_FRAG FIELD32(0x00000001) +#define TXWI_W0_MIMO_PS FIELD32(0x00000002) +#define TXWI_W0_CF_ACK FIELD32(0x00000004) +#define TXWI_W0_TS FIELD32(0x00000008) +#define TXWI_W0_AMPDU FIELD32(0x00000010) +#define TXWI_W0_MPDU_DENSITY FIELD32(0x000000e0) +#define TXWI_W0_TX_OP FIELD32(0x00000300) +#define TXWI_W0_MCS FIELD32(0x007f0000) +#define TXWI_W0_BW FIELD32(0x00800000) +#define TXWI_W0_SHORT_GI FIELD32(0x01000000) +#define TXWI_W0_STBC FIELD32(0x06000000) +#define TXWI_W0_IFS FIELD32(0x08000000) +#define TXWI_W0_PHYMODE FIELD32(0xc0000000) + +/* + * Word1 + */ +#define TXWI_W1_ACK FIELD32(0x00000001) +#define TXWI_W1_NSEQ FIELD32(0x00000002) +#define TXWI_W1_BW_WIN_SIZE FIELD32(0x000000fc) +#define TXWI_W1_WIRELESS_CLI_ID FIELD32(0x0000ff00) +#define TXWI_W1_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) +#define TXWI_W1_PACKETID FIELD32(0xf0000000) + +/* + * Word2 + */ +#define TXWI_W2_IV FIELD32(0xffffffff) + +/* + * Word3 + */ +#define TXWI_W3_EIV FIELD32(0xffffffff) + +/* + * RX WI structure + */ + +/* + * Word0 + */ +#define RXWI_W0_WIRELESS_CLI_ID FIELD32(0x000000ff) +#define RXWI_W0_KEY_INDEX FIELD32(0x00000300) +#define RXWI_W0_BSSID FIELD32(0x00001c00) +#define RXWI_W0_UDF FIELD32(0x0000e000) +#define RXWI_W0_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) +#define RXWI_W0_TID FIELD32(0xf0000000) + +/* + * Word1 + */ +#define RXWI_W1_FRAG FIELD32(0x0000000f) +#define RXWI_W1_SEQUENCE FIELD32(0x0000fff0) +#define RXWI_W1_MCS FIELD32(0x007f0000) +#define RXWI_W1_BW FIELD32(0x00800000) +#define RXWI_W1_SHORT_GI FIELD32(0x01000000) +#define RXWI_W1_STBC FIELD32(0x06000000) +#define RXWI_W1_PHYMODE FIELD32(0xc0000000) + +/* + * Word2 + */ +#define RXWI_W2_RSSI0 FIELD32(0x000000ff) +#define RXWI_W2_RSSI1 FIELD32(0x0000ff00) +#define RXWI_W2_RSSI2 FIELD32(0x00ff0000) + +/* + * Word3 + */ +#define RXWI_W3_SNR0 FIELD32(0x000000ff) +#define RXWI_W3_SNR1 FIELD32(0x0000ff00) + +/* + * Macros for converting txpower from EEPROM to mac80211 value + * and from mac80211 value to register value. + */ +#define MIN_G_TXPOWER 0 +#define MIN_A_TXPOWER -7 +#define MAX_G_TXPOWER 31 +#define MAX_A_TXPOWER 15 +#define DEFAULT_TXPOWER 5 + +#define TXPOWER_G_FROM_DEV(__txpower) \ + ((__txpower) > MAX_G_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) + +#define TXPOWER_G_TO_DEV(__txpower) \ + clamp_t(char, __txpower, MIN_G_TXPOWER, MAX_G_TXPOWER) + +#define TXPOWER_A_FROM_DEV(__txpower) \ + ((__txpower) > MAX_A_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) + +#define TXPOWER_A_TO_DEV(__txpower) \ + clamp_t(char, __txpower, MIN_A_TXPOWER, MAX_A_TXPOWER) + +#endif /* RT2800_H */ diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c new file mode 100644 index 0000000..5c7d74a --- /dev/null +++ b/drivers/net/wireless/rt2x00/rt2800lib.c @@ -0,0 +1,1817 @@ +/* + Copyright (C) 2009 Bartlomiej Zolnierkiewicz + + Based on the original rt2800pci.c and rt2800usb.c: + + Copyright (C) 2004 - 2009 rt2x00 SourceForge Project + <http://rt2x00.serialmonkey.com> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the + Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +/* + Module: rt2800lib + Abstract: rt2800 generic device routines. + */ + +#include <linux/kernel.h> +#include <linux/module.h> + +#include "rt2x00.h" +#ifdef CONFIG_RT2800USB +#include "rt2x00usb.h" +#endif +#include "rt2800lib.h" +#include "rt2800.h" +#include "rt2800usb.h" + +MODULE_AUTHOR("Bartlomiej Zolnierkiewicz"); +MODULE_DESCRIPTION("rt2800 library"); +MODULE_LICENSE("GPL"); + +/* + * Register access. + * All access to the CSR registers will go through the methods + * rt2800_register_read and rt2800_register_write. + * BBP and RF register require indirect register access, + * and use the CSR registers BBPCSR and RFCSR to achieve this. + * These indirect registers work with busy bits, + * and we will try maximal REGISTER_BUSY_COUNT times to access + * the register while taking a REGISTER_BUSY_DELAY us delay + * between each attampt. When the busy bit is still set at that time, + * the access attempt is considered to have failed, + * and we will print an error. + * The _lock versions must be used if you already hold the csr_mutex + */ +#define WAIT_FOR_BBP(__dev, __reg) \ + rt2800_regbusy_read((__dev), BBP_CSR_CFG, BBP_CSR_CFG_BUSY, (__reg)) +#define WAIT_FOR_RFCSR(__dev, __reg) \ + rt2800_regbusy_read((__dev), RF_CSR_CFG, RF_CSR_CFG_BUSY, (__reg)) +#define WAIT_FOR_RF(__dev, __reg) \ + rt2800_regbusy_read((__dev), RF_CSR_CFG0, RF_CSR_CFG0_BUSY, (__reg)) +#define WAIT_FOR_MCU(__dev, __reg) \ + rt2800_regbusy_read((__dev), H2M_MAILBOX_CSR, \ + H2M_MAILBOX_CSR_OWNER, (__reg)) + +static void rt2800_bbp_write(struct rt2x00_dev *rt2x00dev, + const unsigned int word, const u8 value) +{ + u32 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the BBP becomes available, afterwards we + * can safely write the new data into the register. + */ + if (WAIT_FOR_BBP(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field32(®, BBP_CSR_CFG_VALUE, value); + rt2x00_set_field32(®, BBP_CSR_CFG_REGNUM, word); + rt2x00_set_field32(®, BBP_CSR_CFG_BUSY, 1); + rt2x00_set_field32(®, BBP_CSR_CFG_READ_CONTROL, 0); + if (rt2x00_intf_is_pci(rt2x00dev)) + rt2x00_set_field32(®, BBP_CSR_CFG_BBP_RW_MODE, 1); + + rt2800_register_write_lock(rt2x00dev, BBP_CSR_CFG, reg); + } + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +static void rt2800_bbp_read(struct rt2x00_dev *rt2x00dev, + const unsigned int word, u8 *value) +{ + u32 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the BBP becomes available, afterwards we + * can safely write the read request into the register. + * After the data has been written, we wait until hardware + * returns the correct value, if at any time the register + * doesn't become available in time, reg will be 0xffffffff + * which means we return 0xff to the caller. + */ + if (WAIT_FOR_BBP(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field32(®, BBP_CSR_CFG_REGNUM, word); + rt2x00_set_field32(®, BBP_CSR_CFG_BUSY, 1); + rt2x00_set_field32(®, BBP_CSR_CFG_READ_CONTROL, 1); + if (rt2x00_intf_is_pci(rt2x00dev)) + rt2x00_set_field32(®, BBP_CSR_CFG_BBP_RW_MODE, 1); + + rt2800_register_write_lock(rt2x00dev, BBP_CSR_CFG, reg); + + WAIT_FOR_BBP(rt2x00dev, ®); + } + + *value = rt2x00_get_field32(reg, BBP_CSR_CFG_VALUE); + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +static void rt2800_rfcsr_write(struct rt2x00_dev *rt2x00dev, + const unsigned int word, const u8 value) +{ + u32 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the RFCSR becomes available, afterwards we + * can safely write the new data into the register. + */ + if (WAIT_FOR_RFCSR(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field32(®, RF_CSR_CFG_DATA, value); + rt2x00_set_field32(®, RF_CSR_CFG_REGNUM, word); + rt2x00_set_field32(®, RF_CSR_CFG_WRITE, 1); + rt2x00_set_field32(®, RF_CSR_CFG_BUSY, 1); + + rt2800_register_write_lock(rt2x00dev, RF_CSR_CFG, reg); + } + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +static void rt2800_rfcsr_read(struct rt2x00_dev *rt2x00dev, + const unsigned int word, u8 *value) +{ + u32 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the RFCSR becomes available, afterwards we + * can safely write the read request into the register. + * After the data has been written, we wait until hardware + * returns the correct value, if at any time the register + * doesn't become available in time, reg will be 0xffffffff + * which means we return 0xff to the caller. + */ + if (WAIT_FOR_RFCSR(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field32(®, RF_CSR_CFG_REGNUM, word); + rt2x00_set_field32(®, RF_CSR_CFG_WRITE, 0); + rt2x00_set_field32(®, RF_CSR_CFG_BUSY, 1); + + rt2800_register_write_lock(rt2x00dev, RF_CSR_CFG, reg); + + WAIT_FOR_RFCSR(rt2x00dev, ®); + } + + *value = rt2x00_get_field32(reg, RF_CSR_CFG_DATA); + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +static void rt2800_rf_write(struct rt2x00_dev *rt2x00dev, + const unsigned int word, const u32 value) +{ + u32 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the RF becomes available, afterwards we + * can safely write the new data into the register. + */ + if (WAIT_FOR_RF(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field32(®, RF_CSR_CFG0_REG_VALUE_BW, value); + rt2x00_set_field32(®, RF_CSR_CFG0_STANDBYMODE, 0); + rt2x00_set_field32(®, RF_CSR_CFG0_SEL, 0); + rt2x00_set_field32(®, RF_CSR_CFG0_BUSY, 1); + + rt2800_register_write_lock(rt2x00dev, RF_CSR_CFG0, reg); + rt2x00_rf_write(rt2x00dev, word, value); + } + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +void rt2800_mcu_request(struct rt2x00_dev *rt2x00dev, + const u8 command, const u8 token, + const u8 arg0, const u8 arg1) +{ + u32 reg; + + if (rt2x00_intf_is_pci(rt2x00dev)) { + /* + * RT2880 and RT3052 don't support MCU requests. + */ + if (rt2x00_rt(&rt2x00dev->chip, RT2880) || + rt2x00_rt(&rt2x00dev->chip, RT3052)) + return; + } + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the MCU becomes available, afterwards we + * can safely write the new data into the register. + */ + if (WAIT_FOR_MCU(rt2x00dev, ®)) { + rt2x00_set_field32(®, H2M_MAILBOX_CSR_OWNER, 1); + rt2x00_set_field32(®, H2M_MAILBOX_CSR_CMD_TOKEN, token); + rt2x00_set_field32(®, H2M_MAILBOX_CSR_ARG0, arg0); + rt2x00_set_field32(®, H2M_MAILBOX_CSR_ARG1, arg1); + rt2800_register_write_lock(rt2x00dev, H2M_MAILBOX_CSR, reg); + + reg = 0; + rt2x00_set_field32(®, HOST_CMD_CSR_HOST_COMMAND, command); + rt2800_register_write_lock(rt2x00dev, HOST_CMD_CSR, reg); + } + + mutex_unlock(&rt2x00dev->csr_mutex); +} +EXPORT_SYMBOL_GPL(rt2800_mcu_request); + +#ifdef CONFIG_RT2X00_LIB_DEBUGFS +const struct rt2x00debug rt2800_rt2x00debug = { + .owner = THIS_MODULE, + .csr = { + .read = rt2800_register_read, + .write = rt2800_register_write, + .flags = RT2X00DEBUGFS_OFFSET, + .word_base = CSR_REG_BASE, + .word_size = sizeof(u32), + .word_count = CSR_REG_SIZE / sizeof(u32), + }, + .eeprom = { + .read = rt2x00_eeprom_read, + .write = rt2x00_eeprom_write, + .word_base = EEPROM_BASE, + .word_size = sizeof(u16), + .word_count = EEPROM_SIZE / sizeof(u16), + }, + .bbp = { + .read = rt2800_bbp_read, + .write = rt2800_bbp_write, + .word_base = BBP_BASE, + .word_size = sizeof(u8), + .word_count = BBP_SIZE / sizeof(u8), + }, + .rf = { + .read = rt2x00_rf_read, + .write = rt2800_rf_write, + .word_base = RF_BASE, + .word_size = sizeof(u32), + .word_count = RF_SIZE / sizeof(u32), + }, +}; +EXPORT_SYMBOL_GPL(rt2800_rt2x00debug); +#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ + +int rt2800_rfkill_poll(struct rt2x00_dev *rt2x00dev) +{ + u32 reg; + + rt2800_register_read(rt2x00dev, GPIO_CTRL_CFG, ®); + return rt2x00_get_field32(reg, GPIO_CTRL_CFG_BIT2); +} +EXPORT_SYMBOL_GPL(rt2800_rfkill_poll); + +#ifdef CONFIG_RT2X00_LIB_LEDS +static void rt2800_brightness_set(struct led_classdev *led_cdev, + enum led_brightness brightness) +{ + struct rt2x00_led *led = + container_of(led_cdev, struct rt2x00_led, led_dev); + unsigned int enabled = brightness != LED_OFF; + unsigned int bg_mode = + (enabled && led->rt2x00dev->curr_band == IEEE80211_BAND_2GHZ); + unsigned int polarity = + rt2x00_get_field16(led->rt2x00dev->led_mcu_reg, + EEPROM_FREQ_LED_POLARITY); + unsigned int ledmode = + rt2x00_get_field16(led->rt2x00dev->led_mcu_reg, + EEPROM_FREQ_LED_MODE); + + if (led->type == LED_TYPE_RADIO) { + rt2800_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode, + enabled ? 0x20 : 0); + } else if (led->type == LED_TYPE_ASSOC) { + rt2800_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode, + enabled ? (bg_mode ? 0x60 : 0xa0) : 0x20); + } else if (led->type == LED_TYPE_QUALITY) { + /* + * The brightness is divided into 6 levels (0 - 5), + * The specs tell us the following levels: + * 0, 1 ,3, 7, 15, 31 + * to determine the level in a simple way we can simply + * work with bitshifting: + * (1 << level) - 1 + */ + rt2800_mcu_request(led->rt2x00dev, MCU_LED_STRENGTH, 0xff, + (1 << brightness / (LED_FULL / 6)) - 1, + polarity); + } +} + +static int rt2800_blink_set(struct led_classdev *led_cdev, + unsigned long *delay_on, unsigned long *delay_off) +{ + struct rt2x00_led *led = + container_of(led_cdev, struct rt2x00_led, led_dev); + u32 reg; + + rt2800_register_read(led->rt2x00dev, LED_CFG, ®); + rt2x00_set_field32(®, LED_CFG_ON_PERIOD, *delay_on); + rt2x00_set_field32(®, LED_CFG_OFF_PERIOD, *delay_off); + rt2x00_set_field32(®, LED_CFG_SLOW_BLINK_PERIOD, 3); + rt2x00_set_field32(®, LED_CFG_R_LED_MODE, 3); + rt2x00_set_field32(®, LED_CFG_G_LED_MODE, 12); + rt2x00_set_field32(®, LED_CFG_Y_LED_MODE, 3); + rt2x00_set_field32(®, LED_CFG_LED_POLAR, 1); + rt2800_register_write(led->rt2x00dev, LED_CFG, reg); + + return 0; +} + +void rt2800_init_led(struct rt2x00_dev *rt2x00dev, + struct rt2x00_led *led, enum led_type type) +{ + led->rt2x00dev = rt2x00dev; + led->type = type; + led->led_dev.brightness_set = rt2800_brightness_set; + led->led_dev.blink_set = rt2800_blink_set; + led->flags = LED_INITIALIZED; +} +EXPORT_SYMBOL_GPL(rt2800_init_led); +#endif /* CONFIG_RT2X00_LIB_LEDS */ + +/* + * Configuration handlers. + */ +static void rt2800_config_wcid_attr(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key) +{ + struct mac_wcid_entry wcid_entry; + struct mac_iveiv_entry iveiv_entry; + u32 offset; + u32 reg; + + offset = MAC_WCID_ATTR_ENTRY(key->hw_key_idx); + + rt2800_register_read(rt2x00dev, offset, ®); + rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_KEYTAB, + !!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)); + rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_CIPHER, + (crypto->cmd == SET_KEY) * crypto->cipher); + rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_BSS_IDX, + (crypto->cmd == SET_KEY) * crypto->bssidx); + rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_RX_WIUDF, crypto->cipher); + rt2800_register_write(rt2x00dev, offset, reg); + + offset = MAC_IVEIV_ENTRY(key->hw_key_idx); + + memset(&iveiv_entry, 0, sizeof(iveiv_entry)); + if ((crypto->cipher == CIPHER_TKIP) || + (crypto->cipher == CIPHER_TKIP_NO_MIC) || + (crypto->cipher == CIPHER_AES)) + iveiv_entry.iv[3] |= 0x20; + iveiv_entry.iv[3] |= key->keyidx << 6; + rt2800_register_multiwrite(rt2x00dev, offset, + &iveiv_entry, sizeof(iveiv_entry)); + + offset = MAC_WCID_ENTRY(key->hw_key_idx); + + memset(&wcid_entry, 0, sizeof(wcid_entry)); + if (crypto->cmd == SET_KEY) + memcpy(&wcid_entry, crypto->address, ETH_ALEN); + rt2800_register_multiwrite(rt2x00dev, offset, + &wcid_entry, sizeof(wcid_entry)); +} + +int rt2800_config_shared_key(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key) +{ + struct hw_key_entry key_entry; + struct rt2x00_field32 field; + u32 offset; + u32 reg; + + if (crypto->cmd == SET_KEY) { + key->hw_key_idx = (4 * crypto->bssidx) + key->keyidx; + + memcpy(key_entry.key, crypto->key, + sizeof(key_entry.key)); + memcpy(key_entry.tx_mic, crypto->tx_mic, + sizeof(key_entry.tx_mic)); + memcpy(key_entry.rx_mic, crypto->rx_mic, + sizeof(key_entry.rx_mic)); + + offset = SHARED_KEY_ENTRY(key->hw_key_idx); + rt2800_register_multiwrite(rt2x00dev, offset, + &key_entry, sizeof(key_entry)); + } + + /* + * The cipher types are stored over multiple registers + * starting with SHARED_KEY_MODE_BASE each word will have + * 32 bits and contains the cipher types for 2 bssidx each. + * Using the correct defines correctly will cause overhead, + * so just calculate the correct offset. + */ + field.bit_offset = 4 * (key->hw_key_idx % 8); + field.bit_mask = 0x7 << field.bit_offset; + + offset = SHARED_KEY_MODE_ENTRY(key->hw_key_idx / 8); + + rt2800_register_read(rt2x00dev, offset, ®); + rt2x00_set_field32(®, field, + (crypto->cmd == SET_KEY) * crypto->cipher); + rt2800_register_write(rt2x00dev, offset, reg); + + /* + * Update WCID information + */ + rt2800_config_wcid_attr(rt2x00dev, crypto, key); + + return 0; +} +EXPORT_SYMBOL_GPL(rt2800_config_shared_key); + +int rt2800_config_pairwise_key(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key) +{ + struct hw_key_entry key_entry; + u32 offset; + + if (crypto->cmd == SET_KEY) { + /* + * 1 pairwise key is possible per AID, this means that the AID + * equals our hw_key_idx. Make sure the WCID starts _after_ the + * last possible shared key entry. + */ + if (crypto->aid > (256 - 32)) + return -ENOSPC; + + key->hw_key_idx = 32 + crypto->aid; + + memcpy(key_entry.key, crypto->key, + sizeof(key_entry.key)); + memcpy(key_entry.tx_mic, crypto->tx_mic, + sizeof(key_entry.tx_mic)); + memcpy(key_entry.rx_mic, crypto->rx_mic, + sizeof(key_entry.rx_mic)); + + offset = PAIRWISE_KEY_ENTRY(key->hw_key_idx); + rt2800_register_multiwrite(rt2x00dev, offset, + &key_entry, sizeof(key_entry)); + } + + /* + * Update WCID information + */ + rt2800_config_wcid_attr(rt2x00dev, crypto, key); + + return 0; +} +EXPORT_SYMBOL_GPL(rt2800_config_pairwise_key); + +void rt2800_config_filter(struct rt2x00_dev *rt2x00dev, + const unsigned int filter_flags) +{ + u32 reg; + + /* + * Start configuration steps. + * Note that the version error will always be dropped + * and broadcast frames will always be accepted since + * there is no filter for it at this time. + */ + rt2800_register_read(rt2x00dev, RX_FILTER_CFG, ®); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CRC_ERROR, + !(filter_flags & FIF_FCSFAIL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PHY_ERROR, + !(filter_flags & FIF_PLCPFAIL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_NOT_TO_ME, + !(filter_flags & FIF_PROMISC_IN_BSS)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_NOT_MY_BSSD, 0); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_VER_ERROR, 1); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_MULTICAST, + !(filter_flags & FIF_ALLMULTI)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BROADCAST, 0); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_DUPLICATE, 1); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CF_END_ACK, + !(filter_flags & FIF_CONTROL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CF_END, + !(filter_flags & FIF_CONTROL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_ACK, + !(filter_flags & FIF_CONTROL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CTS, + !(filter_flags & FIF_CONTROL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_RTS, + !(filter_flags & FIF_CONTROL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PSPOLL, + !(filter_flags & FIF_PSPOLL)); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BA, 1); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BAR, 0); + rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CNTL, + !(filter_flags & FIF_CONTROL)); + rt2800_register_write(rt2x00dev, RX_FILTER_CFG, reg); +} +EXPORT_SYMBOL_GPL(rt2800_config_filter); + +void rt2800_config_intf(struct rt2x00_dev *rt2x00dev, struct rt2x00_intf *intf, + struct rt2x00intf_conf *conf, const unsigned int flags) +{ + unsigned int beacon_base; + u32 reg; + + if (flags & CONFIG_UPDATE_TYPE) { + /* + * Clear current synchronisation setup. + * For the Beacon base registers we only need to clear + * the first byte since that byte contains the VALID and OWNER + * bits which (when set to 0) will invalidate the entire beacon. + */ + beacon_base = HW_BEACON_OFFSET(intf->beacon->entry_idx); + rt2800_register_write(rt2x00dev, beacon_base, 0); + + /* + * Enable synchronisation. + */ + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1); + rt2x00_set_field32(®, BCN_TIME_CFG_TSF_SYNC, conf->sync); + rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); + } + + if (flags & CONFIG_UPDATE_MAC) { + reg = le32_to_cpu(conf->mac[1]); + rt2x00_set_field32(®, MAC_ADDR_DW1_UNICAST_TO_ME_MASK, 0xff); + conf->mac[1] = cpu_to_le32(reg); + + rt2800_register_multiwrite(rt2x00dev, MAC_ADDR_DW0, + conf->mac, sizeof(conf->mac)); + } + + if (flags & CONFIG_UPDATE_BSSID) { + reg = le32_to_cpu(conf->bssid[1]); + rt2x00_set_field32(®, MAC_BSSID_DW1_BSS_ID_MASK, 0); + rt2x00_set_field32(®, MAC_BSSID_DW1_BSS_BCN_NUM, 0); + conf->bssid[1] = cpu_to_le32(reg); + + rt2800_register_multiwrite(rt2x00dev, MAC_BSSID_DW0, + conf->bssid, sizeof(conf->bssid)); + } +} +EXPORT_SYMBOL_GPL(rt2800_config_intf); + +void rt2800_config_erp(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_erp *erp) +{ + u32 reg; + + rt2800_register_read(rt2x00dev, TX_TIMEOUT_CFG, ®); + rt2x00_set_field32(®, TX_TIMEOUT_CFG_RX_ACK_TIMEOUT, 0x20); + rt2800_register_write(rt2x00dev, TX_TIMEOUT_CFG, reg); + + rt2800_register_read(rt2x00dev, AUTO_RSP_CFG, ®); + rt2x00_set_field32(®, AUTO_RSP_CFG_BAC_ACK_POLICY, + !!erp->short_preamble); + rt2x00_set_field32(®, AUTO_RSP_CFG_AR_PREAMBLE, + !!erp->short_preamble); + rt2800_register_write(rt2x00dev, AUTO_RSP_CFG, reg); + + rt2800_register_read(rt2x00dev, OFDM_PROT_CFG, ®); + rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, + erp->cts_protection ? 2 : 0); + rt2800_register_write(rt2x00dev, OFDM_PROT_CFG, reg); + + rt2800_register_write(rt2x00dev, LEGACY_BASIC_RATE, + erp->basic_rates); + rt2800_register_write(rt2x00dev, HT_BASIC_RATE, 0x00008003); + + rt2800_register_read(rt2x00dev, BKOFF_SLOT_CFG, ®); + rt2x00_set_field32(®, BKOFF_SLOT_CFG_SLOT_TIME, erp->slot_time); + rt2x00_set_field32(®, BKOFF_SLOT_CFG_CC_DELAY_TIME, 2); + rt2800_register_write(rt2x00dev, BKOFF_SLOT_CFG, reg); + + rt2800_register_read(rt2x00dev, XIFS_TIME_CFG, ®); + rt2x00_set_field32(®, XIFS_TIME_CFG_CCKM_SIFS_TIME, erp->sifs); + rt2x00_set_field32(®, XIFS_TIME_CFG_OFDM_SIFS_TIME, erp->sifs); + rt2x00_set_field32(®, XIFS_TIME_CFG_OFDM_XIFS_TIME, 4); + rt2x00_set_field32(®, XIFS_TIME_CFG_EIFS, erp->eifs); + rt2x00_set_field32(®, XIFS_TIME_CFG_BB_RXEND_ENABLE, 1); + rt2800_register_write(rt2x00dev, XIFS_TIME_CFG, reg); + + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_INTERVAL, + erp->beacon_int * 16); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); +} +EXPORT_SYMBOL_GPL(rt2800_config_erp); + +void rt2800_config_ant(struct rt2x00_dev *rt2x00dev, struct antenna_setup *ant) +{ + u8 r1; + u8 r3; + + rt2800_bbp_read(rt2x00dev, 1, &r1); + rt2800_bbp_read(rt2x00dev, 3, &r3); + + /* + * Configure the TX antenna. + */ + switch ((int)ant->tx) { + case 1: + rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 0); + if (rt2x00_intf_is_pci(rt2x00dev)) + rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 0); + break; + case 2: + rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 2); + break; + case 3: + /* Do nothing */ + break; + } + + /* + * Configure the RX antenna. + */ + switch ((int)ant->rx) { + case 1: + rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 0); + break; + case 2: + rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 1); + break; + case 3: + rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 2); + break; + } + + rt2800_bbp_write(rt2x00dev, 3, r3); + rt2800_bbp_write(rt2x00dev, 1, r1); +} +EXPORT_SYMBOL_GPL(rt2800_config_ant); + +static void rt2800_config_lna_gain(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf) +{ + u16 eeprom; + short lna_gain; + + if (libconf->rf.channel <= 14) { + rt2x00_eeprom_read(rt2x00dev, EEPROM_LNA, &eeprom); + lna_gain = rt2x00_get_field16(eeprom, EEPROM_LNA_BG); + } else if (libconf->rf.channel <= 64) { + rt2x00_eeprom_read(rt2x00dev, EEPROM_LNA, &eeprom); + lna_gain = rt2x00_get_field16(eeprom, EEPROM_LNA_A0); + } else if (libconf->rf.channel <= 128) { + rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_BG2, &eeprom); + lna_gain = rt2x00_get_field16(eeprom, EEPROM_RSSI_BG2_LNA_A1); + } else { + rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_A2, &eeprom); + lna_gain = rt2x00_get_field16(eeprom, EEPROM_RSSI_A2_LNA_A2); + } + + rt2x00dev->lna_gain = lna_gain; +} + +static void rt2800_config_channel_rt2x(struct rt2x00_dev *rt2x00dev, + struct ieee80211_conf *conf, + struct rf_channel *rf, + struct channel_info *info) +{ + rt2x00_set_field32(&rf->rf4, RF4_FREQ_OFFSET, rt2x00dev->freq_offset); + + if (rt2x00dev->default_ant.tx == 1) + rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_TX1, 1); + + if (rt2x00dev->default_ant.rx == 1) { + rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX1, 1); + rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1); + } else if (rt2x00dev->default_ant.rx == 2) + rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1); + + if (rf->channel > 14) { + /* + * When TX power is below 0, we should increase it by 7 to + * make it a positive value (Minumum value is -7). + * However this means that values between 0 and 7 have + * double meaning, and we should set a 7DBm boost flag. + */ + rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_A_7DBM_BOOST, + (info->tx_power1 >= 0)); + + if (info->tx_power1 < 0) + info->tx_power1 += 7; + + rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_A, + TXPOWER_A_TO_DEV(info->tx_power1)); + + rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_A_7DBM_BOOST, + (info->tx_power2 >= 0)); + + if (info->tx_power2 < 0) + info->tx_power2 += 7; + + rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_A, + TXPOWER_A_TO_DEV(info->tx_power2)); + } else { + rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_G, + TXPOWER_G_TO_DEV(info->tx_power1)); + rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_G, + TXPOWER_G_TO_DEV(info->tx_power2)); + } + + rt2x00_set_field32(&rf->rf4, RF4_HT40, conf_is_ht40(conf)); + + rt2800_rf_write(rt2x00dev, 1, rf->rf1); + rt2800_rf_write(rt2x00dev, 2, rf->rf2); + rt2800_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); + rt2800_rf_write(rt2x00dev, 4, rf->rf4); + + udelay(200); + + rt2800_rf_write(rt2x00dev, 1, rf->rf1); + rt2800_rf_write(rt2x00dev, 2, rf->rf2); + rt2800_rf_write(rt2x00dev, 3, rf->rf3 | 0x00000004); + rt2800_rf_write(rt2x00dev, 4, rf->rf4); + + udelay(200); + + rt2800_rf_write(rt2x00dev, 1, rf->rf1); + rt2800_rf_write(rt2x00dev, 2, rf->rf2); + rt2800_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); + rt2800_rf_write(rt2x00dev, 4, rf->rf4); +} + +static void rt2800_config_channel_rt3x(struct rt2x00_dev *rt2x00dev, + struct ieee80211_conf *conf, + struct rf_channel *rf, + struct channel_info *info) +{ + u8 rfcsr; + + rt2800_rfcsr_write(rt2x00dev, 2, rf->rf1); + rt2800_rfcsr_write(rt2x00dev, 2, rf->rf3); + + rt2800_rfcsr_read(rt2x00dev, 6, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR6_R, rf->rf2); + rt2800_rfcsr_write(rt2x00dev, 6, rfcsr); + + rt2800_rfcsr_read(rt2x00dev, 12, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR12_TX_POWER, + TXPOWER_G_TO_DEV(info->tx_power1)); + rt2800_rfcsr_write(rt2x00dev, 12, rfcsr); + + rt2800_rfcsr_read(rt2x00dev, 23, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR23_FREQ_OFFSET, rt2x00dev->freq_offset); + rt2800_rfcsr_write(rt2x00dev, 23, rfcsr); + + rt2800_rfcsr_write(rt2x00dev, 24, + rt2x00dev->calibration[conf_is_ht40(conf)]); + + rt2800_rfcsr_read(rt2x00dev, 23, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR7_RF_TUNING, 1); + rt2800_rfcsr_write(rt2x00dev, 23, rfcsr); +} + +static void rt2800_config_channel(struct rt2x00_dev *rt2x00dev, + struct ieee80211_conf *conf, + struct rf_channel *rf, + struct channel_info *info) +{ + u32 reg; + unsigned int tx_pin; + u8 bbp; + + if (rt2x00_rev(&rt2x00dev->chip) != RT3070_VERSION) + rt2800_config_channel_rt2x(rt2x00dev, conf, rf, info); + else + rt2800_config_channel_rt3x(rt2x00dev, conf, rf, info); + + /* + * Change BBP settings + */ + rt2800_bbp_write(rt2x00dev, 62, 0x37 - rt2x00dev->lna_gain); + rt2800_bbp_write(rt2x00dev, 63, 0x37 - rt2x00dev->lna_gain); + rt2800_bbp_write(rt2x00dev, 64, 0x37 - rt2x00dev->lna_gain); + rt2800_bbp_write(rt2x00dev, 86, 0); + + if (rf->channel <= 14) { + if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags)) { + rt2800_bbp_write(rt2x00dev, 82, 0x62); + rt2800_bbp_write(rt2x00dev, 75, 0x46); + } else { + rt2800_bbp_write(rt2x00dev, 82, 0x84); + rt2800_bbp_write(rt2x00dev, 75, 0x50); + } + } else { + rt2800_bbp_write(rt2x00dev, 82, 0xf2); + + if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags)) + rt2800_bbp_write(rt2x00dev, 75, 0x46); + else + rt2800_bbp_write(rt2x00dev, 75, 0x50); + } + + rt2800_register_read(rt2x00dev, TX_BAND_CFG, ®); + rt2x00_set_field32(®, TX_BAND_CFG_HT40_PLUS, conf_is_ht40_plus(conf)); + rt2x00_set_field32(®, TX_BAND_CFG_A, rf->channel > 14); + rt2x00_set_field32(®, TX_BAND_CFG_BG, rf->channel <= 14); + rt2800_register_write(rt2x00dev, TX_BAND_CFG, reg); + + tx_pin = 0; + + /* Turn on unused PA or LNA when not using 1T or 1R */ + if (rt2x00dev->default_ant.tx != 1) { + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A1_EN, 1); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G1_EN, 1); + } + + /* Turn on unused PA or LNA when not using 1T or 1R */ + if (rt2x00dev->default_ant.rx != 1) { + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A1_EN, 1); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G1_EN, 1); + } + + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A0_EN, 1); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G0_EN, 1); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_RFTR_EN, 1); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_TRSW_EN, 1); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G0_EN, rf->channel <= 14); + rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A0_EN, rf->channel > 14); + + rt2800_register_write(rt2x00dev, TX_PIN_CFG, tx_pin); + + rt2800_bbp_read(rt2x00dev, 4, &bbp); + rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * conf_is_ht40(conf)); + rt2800_bbp_write(rt2x00dev, 4, bbp); + + rt2800_bbp_read(rt2x00dev, 3, &bbp); + rt2x00_set_field8(&bbp, BBP3_HT40_PLUS, conf_is_ht40_plus(conf)); + rt2800_bbp_write(rt2x00dev, 3, bbp); + + if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) { + if (conf_is_ht40(conf)) { + rt2800_bbp_write(rt2x00dev, 69, 0x1a); + rt2800_bbp_write(rt2x00dev, 70, 0x0a); + rt2800_bbp_write(rt2x00dev, 73, 0x16); + } else { + rt2800_bbp_write(rt2x00dev, 69, 0x16); + rt2800_bbp_write(rt2x00dev, 70, 0x08); + rt2800_bbp_write(rt2x00dev, 73, 0x11); + } + } + + msleep(1); +} + +static void rt2800_config_txpower(struct rt2x00_dev *rt2x00dev, + const int txpower) +{ + u32 reg; + u32 value = TXPOWER_G_TO_DEV(txpower); + u8 r1; + + rt2800_bbp_read(rt2x00dev, 1, &r1); + rt2x00_set_field8(®, BBP1_TX_POWER, 0); + rt2800_bbp_write(rt2x00dev, 1, r1); + + rt2800_register_read(rt2x00dev, TX_PWR_CFG_0, ®); + rt2x00_set_field32(®, TX_PWR_CFG_0_1MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_2MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_55MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_11MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_6MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_9MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_12MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_0_18MBS, value); + rt2800_register_write(rt2x00dev, TX_PWR_CFG_0, reg); + + rt2800_register_read(rt2x00dev, TX_PWR_CFG_1, ®); + rt2x00_set_field32(®, TX_PWR_CFG_1_24MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_36MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_48MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_54MBS, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_MCS0, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_MCS1, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_MCS2, value); + rt2x00_set_field32(®, TX_PWR_CFG_1_MCS3, value); + rt2800_register_write(rt2x00dev, TX_PWR_CFG_1, reg); + + rt2800_register_read(rt2x00dev, TX_PWR_CFG_2, ®); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS4, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS5, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS6, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS7, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS8, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS9, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS10, value); + rt2x00_set_field32(®, TX_PWR_CFG_2_MCS11, value); + rt2800_register_write(rt2x00dev, TX_PWR_CFG_2, reg); + + rt2800_register_read(rt2x00dev, TX_PWR_CFG_3, ®); + rt2x00_set_field32(®, TX_PWR_CFG_3_MCS12, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_MCS13, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_MCS14, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_MCS15, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN1, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN2, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN3, value); + rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN4, value); + rt2800_register_write(rt2x00dev, TX_PWR_CFG_3, reg); + + rt2800_register_read(rt2x00dev, TX_PWR_CFG_4, ®); + rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN5, value); + rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN6, value); + rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN7, value); + rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN8, value); + rt2800_register_write(rt2x00dev, TX_PWR_CFG_4, reg); +} + +static void rt2800_config_retry_limit(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf) +{ + u32 reg; + + rt2800_register_read(rt2x00dev, TX_RTY_CFG, ®); + rt2x00_set_field32(®, TX_RTY_CFG_SHORT_RTY_LIMIT, + libconf->conf->short_frame_max_tx_count); + rt2x00_set_field32(®, TX_RTY_CFG_LONG_RTY_LIMIT, + libconf->conf->long_frame_max_tx_count); + rt2x00_set_field32(®, TX_RTY_CFG_LONG_RTY_THRE, 2000); + rt2x00_set_field32(®, TX_RTY_CFG_NON_AGG_RTY_MODE, 0); + rt2x00_set_field32(®, TX_RTY_CFG_AGG_RTY_MODE, 0); + rt2x00_set_field32(®, TX_RTY_CFG_TX_AUTO_FB_ENABLE, 1); + rt2800_register_write(rt2x00dev, TX_RTY_CFG, reg); +} + +static void rt2800_config_ps(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf) +{ + enum dev_state state = + (libconf->conf->flags & IEEE80211_CONF_PS) ? + STATE_SLEEP : STATE_AWAKE; + u32 reg; + + if (state == STATE_SLEEP) { + rt2800_register_write(rt2x00dev, AUTOWAKEUP_CFG, 0); + + rt2800_register_read(rt2x00dev, AUTOWAKEUP_CFG, ®); + rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTO_LEAD_TIME, 5); + rt2x00_set_field32(®, AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE, + libconf->conf->listen_interval - 1); + rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTOWAKE, 1); + rt2800_register_write(rt2x00dev, AUTOWAKEUP_CFG, reg); + + rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); + } else { + rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); + + rt2800_register_read(rt2x00dev, AUTOWAKEUP_CFG, ®); + rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTO_LEAD_TIME, 0); + rt2x00_set_field32(®, AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE, 0); + rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTOWAKE, 0); + rt2800_register_write(rt2x00dev, AUTOWAKEUP_CFG, reg); + } +} + +void rt2800_config(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf, + const unsigned int flags) +{ + /* Always recalculate LNA gain before changing configuration */ + rt2800_config_lna_gain(rt2x00dev, libconf); + + if (flags & IEEE80211_CONF_CHANGE_CHANNEL) + rt2800_config_channel(rt2x00dev, libconf->conf, + &libconf->rf, &libconf->channel); + if (flags & IEEE80211_CONF_CHANGE_POWER) + rt2800_config_txpower(rt2x00dev, libconf->conf->power_level); + if (flags & IEEE80211_CONF_CHANGE_RETRY_LIMITS) + rt2800_config_retry_limit(rt2x00dev, libconf); + if (flags & IEEE80211_CONF_CHANGE_PS) + rt2800_config_ps(rt2x00dev, libconf); +} +EXPORT_SYMBOL_GPL(rt2800_config); + +/* + * Link tuning + */ +void rt2800_link_stats(struct rt2x00_dev *rt2x00dev, struct link_qual *qual) +{ + u32 reg; + + /* + * Update FCS error count from register. + */ + rt2800_register_read(rt2x00dev, RX_STA_CNT0, ®); + qual->rx_failed = rt2x00_get_field32(reg, RX_STA_CNT0_CRC_ERR); +} +EXPORT_SYMBOL_GPL(rt2800_link_stats); + +static u8 rt2800_get_default_vgc(struct rt2x00_dev *rt2x00dev) +{ + if (rt2x00dev->curr_band == IEEE80211_BAND_2GHZ) { + if (rt2x00_intf_is_usb(rt2x00dev) && + rt2x00_rev(&rt2x00dev->chip) == RT3070_VERSION) + return 0x1c + (2 * rt2x00dev->lna_gain); + else + return 0x2e + rt2x00dev->lna_gain; + } + + if (!test_bit(CONFIG_CHANNEL_HT40, &rt2x00dev->flags)) + return 0x32 + (rt2x00dev->lna_gain * 5) / 3; + else + return 0x3a + (rt2x00dev->lna_gain * 5) / 3; +} + +static inline void rt2800_set_vgc(struct rt2x00_dev *rt2x00dev, + struct link_qual *qual, u8 vgc_level) +{ + if (qual->vgc_level != vgc_level) { + rt2800_bbp_write(rt2x00dev, 66, vgc_level); + qual->vgc_level = vgc_level; + qual->vgc_level_reg = vgc_level; + } +} + +void rt2800_reset_tuner(struct rt2x00_dev *rt2x00dev, struct link_qual *qual) +{ + rt2800_set_vgc(rt2x00dev, qual, rt2800_get_default_vgc(rt2x00dev)); +} +EXPORT_SYMBOL_GPL(rt2800_reset_tuner); + +void rt2800_link_tuner(struct rt2x00_dev *rt2x00dev, struct link_qual *qual, + const u32 count) +{ + if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) + return; + + /* + * When RSSI is better then -80 increase VGC level with 0x10 + */ + rt2800_set_vgc(rt2x00dev, qual, + rt2800_get_default_vgc(rt2x00dev) + + ((qual->rssi > -80) * 0x10)); +} +EXPORT_SYMBOL_GPL(rt2800_link_tuner); + +/* + * Initialization functions. + */ +int rt2800_init_registers(struct rt2x00_dev *rt2x00dev) +{ + u32 reg; + unsigned int i; + + if (rt2x00_intf_is_usb(rt2x00dev)) { + /* + * Wait untill BBP and RF are ready. + */ + for (i = 0; i < REGISTER_BUSY_COUNT; i++) { + rt2800_register_read(rt2x00dev, MAC_CSR0, ®); + if (reg && reg != ~0) + break; + msleep(1); + } + + if (i == REGISTER_BUSY_COUNT) { + ERROR(rt2x00dev, "Unstable hardware.\n"); + return -EBUSY; + } + + rt2800_register_read(rt2x00dev, PBF_SYS_CTRL, ®); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, + reg & ~0x00002000); + } else if (rt2x00_intf_is_pci(rt2x00dev)) + rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003); + + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_CSR, 1); + rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_BBP, 1); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + + if (rt2x00_intf_is_usb(rt2x00dev)) { + rt2800_register_write(rt2x00dev, USB_DMA_CFG, 0x00000000); +#ifdef CONFIG_RT2800USB + rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0, + USB_MODE_RESET, REGISTER_TIMEOUT); +#endif + } + + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); + + rt2800_register_read(rt2x00dev, BCN_OFFSET0, ®); + rt2x00_set_field32(®, BCN_OFFSET0_BCN0, 0xe0); /* 0x3800 */ + rt2x00_set_field32(®, BCN_OFFSET0_BCN1, 0xe8); /* 0x3a00 */ + rt2x00_set_field32(®, BCN_OFFSET0_BCN2, 0xf0); /* 0x3c00 */ + rt2x00_set_field32(®, BCN_OFFSET0_BCN3, 0xf8); /* 0x3e00 */ + rt2800_register_write(rt2x00dev, BCN_OFFSET0, reg); + + rt2800_register_read(rt2x00dev, BCN_OFFSET1, ®); + rt2x00_set_field32(®, BCN_OFFSET1_BCN4, 0xc8); /* 0x3200 */ + rt2x00_set_field32(®, BCN_OFFSET1_BCN5, 0xd0); /* 0x3400 */ + rt2x00_set_field32(®, BCN_OFFSET1_BCN6, 0x77); /* 0x1dc0 */ + rt2x00_set_field32(®, BCN_OFFSET1_BCN7, 0x6f); /* 0x1bc0 */ + rt2800_register_write(rt2x00dev, BCN_OFFSET1, reg); + + rt2800_register_write(rt2x00dev, LEGACY_BASIC_RATE, 0x0000013f); + rt2800_register_write(rt2x00dev, HT_BASIC_RATE, 0x00008003); + + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); + + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_INTERVAL, 0); + rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 0); + rt2x00_set_field32(®, BCN_TIME_CFG_TSF_SYNC, 0); + rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 0); + rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0); + rt2x00_set_field32(®, BCN_TIME_CFG_TX_TIME_COMPENSATE, 0); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); + + if (rt2x00_intf_is_usb(rt2x00dev) && + rt2x00_rev(&rt2x00dev->chip) == RT3070_VERSION) { + rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000400); + rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x00000000); + rt2800_register_write(rt2x00dev, TX_SW_CFG2, 0x00000000); + } else { + rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000000); + rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x00080606); + } + + rt2800_register_read(rt2x00dev, TX_LINK_CFG, ®); + rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFB_LIFETIME, 32); + rt2x00_set_field32(®, TX_LINK_CFG_MFB_ENABLE, 0); + rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_UMFS_ENABLE, 0); + rt2x00_set_field32(®, TX_LINK_CFG_TX_MRQ_EN, 0); + rt2x00_set_field32(®, TX_LINK_CFG_TX_RDG_EN, 0); + rt2x00_set_field32(®, TX_LINK_CFG_TX_CF_ACK_EN, 1); + rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFB, 0); + rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFS, 0); + rt2800_register_write(rt2x00dev, TX_LINK_CFG, reg); + + rt2800_register_read(rt2x00dev, TX_TIMEOUT_CFG, ®); + rt2x00_set_field32(®, TX_TIMEOUT_CFG_MPDU_LIFETIME, 9); + rt2x00_set_field32(®, TX_TIMEOUT_CFG_TX_OP_TIMEOUT, 10); + rt2800_register_write(rt2x00dev, TX_TIMEOUT_CFG, reg); + + rt2800_register_read(rt2x00dev, MAX_LEN_CFG, ®); + rt2x00_set_field32(®, MAX_LEN_CFG_MAX_MPDU, AGGREGATION_SIZE); + if (rt2x00_rev(&rt2x00dev->chip) >= RT2880E_VERSION && + rt2x00_rev(&rt2x00dev->chip) < RT3070_VERSION) + rt2x00_set_field32(®, MAX_LEN_CFG_MAX_PSDU, 2); + else + rt2x00_set_field32(®, MAX_LEN_CFG_MAX_PSDU, 1); + rt2x00_set_field32(®, MAX_LEN_CFG_MIN_PSDU, 0); + rt2x00_set_field32(®, MAX_LEN_CFG_MIN_MPDU, 0); + rt2800_register_write(rt2x00dev, MAX_LEN_CFG, reg); + + rt2800_register_write(rt2x00dev, PBF_MAX_PCNT, 0x1f3fbf9f); + + rt2800_register_read(rt2x00dev, AUTO_RSP_CFG, ®); + rt2x00_set_field32(®, AUTO_RSP_CFG_AUTORESPONDER, 1); + rt2x00_set_field32(®, AUTO_RSP_CFG_CTS_40_MMODE, 0); + rt2x00_set_field32(®, AUTO_RSP_CFG_CTS_40_MREF, 0); + rt2x00_set_field32(®, AUTO_RSP_CFG_DUAL_CTS_EN, 0); + rt2x00_set_field32(®, AUTO_RSP_CFG_ACK_CTS_PSM_BIT, 0); + rt2800_register_write(rt2x00dev, AUTO_RSP_CFG, reg); + + rt2800_register_read(rt2x00dev, CCK_PROT_CFG, ®); + rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_RATE, 8); + rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_CTRL, 0); + rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_NAV, 1); + rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_CCK, 1); + rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_OFDM, 1); + rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM20, 1); + rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM40, 1); + rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF20, 1); + rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF40, 1); + rt2800_register_write(rt2x00dev, CCK_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, OFDM_PROT_CFG, ®); + rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_RATE, 8); + rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, 0); + rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_NAV, 1); + rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_CCK, 1); + rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_OFDM, 1); + rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM20, 1); + rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM40, 1); + rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF20, 1); + rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF40, 1); + rt2800_register_write(rt2x00dev, OFDM_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, MM20_PROT_CFG, ®); + rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_RATE, 0x4004); + rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_CTRL, 0); + rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_NAV, 1); + rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_CCK, 1); + rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_OFDM, 1); + rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM20, 1); + rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM40, 0); + rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_GF20, 1); + rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_GF40, 0); + rt2800_register_write(rt2x00dev, MM20_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, MM40_PROT_CFG, ®); + rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_RATE, 0x4084); + rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_CTRL, 0); + rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_NAV, 1); + rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_CCK, 1); + rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_OFDM, 1); + rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM20, 1); + rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM40, 1); + rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_GF20, 1); + rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_GF40, 1); + rt2800_register_write(rt2x00dev, MM40_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, GF20_PROT_CFG, ®); + rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_RATE, 0x4004); + rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_CTRL, 0); + rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_NAV, 1); + rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_CCK, 1); + rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_OFDM, 1); + rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM20, 1); + rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM40, 0); + rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_GF20, 1); + rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_GF40, 0); + rt2800_register_write(rt2x00dev, GF20_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, GF40_PROT_CFG, ®); + rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_RATE, 0x4084); + rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_CTRL, 0); + rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_NAV, 1); + rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_CCK, 1); + rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_OFDM, 1); + rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM20, 1); + rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM40, 1); + rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_GF20, 1); + rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_GF40, 1); + rt2800_register_write(rt2x00dev, GF40_PROT_CFG, reg); + + if (rt2x00_intf_is_usb(rt2x00dev)) { + rt2800_register_write(rt2x00dev, PBF_CFG, 0xf40006); + + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_DMA_BUSY, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_DMA_BUSY, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_WP_DMA_BURST_SIZE, 3); + rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_BIG_ENDIAN, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_HDR_SCATTER, 0); + rt2x00_set_field32(®, WPDMA_GLO_CFG_HDR_SEG_LEN, 0); + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); + } + + rt2800_register_write(rt2x00dev, TXOP_CTRL_CFG, 0x0000583f); + rt2800_register_write(rt2x00dev, TXOP_HLDR_ET, 0x00000002); + + rt2800_register_read(rt2x00dev, TX_RTS_CFG, ®); + rt2x00_set_field32(®, TX_RTS_CFG_AUTO_RTS_RETRY_LIMIT, 32); + rt2x00_set_field32(®, TX_RTS_CFG_RTS_THRES, + IEEE80211_MAX_RTS_THRESHOLD); + rt2x00_set_field32(®, TX_RTS_CFG_RTS_FBK_EN, 0); + rt2800_register_write(rt2x00dev, TX_RTS_CFG, reg); + + rt2800_register_write(rt2x00dev, EXP_ACK_TIME, 0x002400ca); + rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003); + + /* + * ASIC will keep garbage value after boot, clear encryption keys. + */ + for (i = 0; i < 4; i++) + rt2800_register_write(rt2x00dev, + SHARED_KEY_MODE_ENTRY(i), 0); + + for (i = 0; i < 256; i++) { + u32 wcid[2] = { 0xffffffff, 0x00ffffff }; + rt2800_register_multiwrite(rt2x00dev, MAC_WCID_ENTRY(i), + wcid, sizeof(wcid)); + + rt2800_register_write(rt2x00dev, MAC_WCID_ATTR_ENTRY(i), 1); + rt2800_register_write(rt2x00dev, MAC_IVEIV_ENTRY(i), 0); + } + + /* + * Clear all beacons + * For the Beacon base registers we only need to clear + * the first byte since that byte contains the VALID and OWNER + * bits which (when set to 0) will invalidate the entire beacon. + */ + rt2800_register_write(rt2x00dev, HW_BEACON_BASE0, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE1, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE2, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE3, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE4, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE5, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE6, 0); + rt2800_register_write(rt2x00dev, HW_BEACON_BASE7, 0); + + if (rt2x00_intf_is_usb(rt2x00dev)) { + rt2800_register_read(rt2x00dev, USB_CYC_CFG, ®); + rt2x00_set_field32(®, USB_CYC_CFG_CLOCK_CYCLE, 30); + rt2800_register_write(rt2x00dev, USB_CYC_CFG, reg); + } + + rt2800_register_read(rt2x00dev, HT_FBK_CFG0, ®); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS0FBK, 0); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS1FBK, 0); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS2FBK, 1); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS3FBK, 2); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS4FBK, 3); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS5FBK, 4); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS6FBK, 5); + rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS7FBK, 6); + rt2800_register_write(rt2x00dev, HT_FBK_CFG0, reg); + + rt2800_register_read(rt2x00dev, HT_FBK_CFG1, ®); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS8FBK, 8); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS9FBK, 8); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS10FBK, 9); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS11FBK, 10); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS12FBK, 11); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS13FBK, 12); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS14FBK, 13); + rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS15FBK, 14); + rt2800_register_write(rt2x00dev, HT_FBK_CFG1, reg); + + rt2800_register_read(rt2x00dev, LG_FBK_CFG0, ®); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS0FBK, 8); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS1FBK, 8); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS2FBK, 9); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS3FBK, 10); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS4FBK, 11); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS5FBK, 12); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS6FBK, 13); + rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS7FBK, 14); + rt2800_register_write(rt2x00dev, LG_FBK_CFG0, reg); + + rt2800_register_read(rt2x00dev, LG_FBK_CFG1, ®); + rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS0FBK, 0); + rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS1FBK, 0); + rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS2FBK, 1); + rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS3FBK, 2); + rt2800_register_write(rt2x00dev, LG_FBK_CFG1, reg); + + /* + * We must clear the error counters. + * These registers are cleared on read, + * so we may pass a useless variable to store the value. + */ + rt2800_register_read(rt2x00dev, RX_STA_CNT0, ®); + rt2800_register_read(rt2x00dev, RX_STA_CNT1, ®); + rt2800_register_read(rt2x00dev, RX_STA_CNT2, ®); + rt2800_register_read(rt2x00dev, TX_STA_CNT0, ®); + rt2800_register_read(rt2x00dev, TX_STA_CNT1, ®); + rt2800_register_read(rt2x00dev, TX_STA_CNT2, ®); + + return 0; +} +EXPORT_SYMBOL_GPL(rt2800_init_registers); + +static int rt2800_wait_bbp_rf_ready(struct rt2x00_dev *rt2x00dev) +{ + unsigned int i; + u32 reg; + + for (i = 0; i < REGISTER_BUSY_COUNT; i++) { + rt2800_register_read(rt2x00dev, MAC_STATUS_CFG, ®); + if (!rt2x00_get_field32(reg, MAC_STATUS_CFG_BBP_RF_BUSY)) + return 0; + + udelay(REGISTER_BUSY_DELAY); + } + + ERROR(rt2x00dev, "BBP/RF register access failed, aborting.\n"); + return -EACCES; +} + +static int rt2800_wait_bbp_ready(struct rt2x00_dev *rt2x00dev) +{ + unsigned int i; + u8 value; + + /* + * BBP was enabled after firmware was loaded, + * but we need to reactivate it now. + */ + rt2800_register_write(rt2x00dev, H2M_BBP_AGENT, 0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); + msleep(1); + + for (i = 0; i < REGISTER_BUSY_COUNT; i++) { + rt2800_bbp_read(rt2x00dev, 0, &value); + if ((value != 0xff) && (value != 0x00)) + return 0; + udelay(REGISTER_BUSY_DELAY); + } + + ERROR(rt2x00dev, "BBP register access failed, aborting.\n"); + return -EACCES; +} + +int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev) +{ + unsigned int i; + u16 eeprom; + u8 reg_id; + u8 value; + + if (unlikely(rt2800_wait_bbp_rf_ready(rt2x00dev) || + rt2800_wait_bbp_ready(rt2x00dev))) + return -EACCES; + + rt2800_bbp_write(rt2x00dev, 65, 0x2c); + rt2800_bbp_write(rt2x00dev, 66, 0x38); + rt2800_bbp_write(rt2x00dev, 69, 0x12); + rt2800_bbp_write(rt2x00dev, 70, 0x0a); + rt2800_bbp_write(rt2x00dev, 73, 0x10); + rt2800_bbp_write(rt2x00dev, 81, 0x37); + rt2800_bbp_write(rt2x00dev, 82, 0x62); + rt2800_bbp_write(rt2x00dev, 83, 0x6a); + rt2800_bbp_write(rt2x00dev, 84, 0x99); + rt2800_bbp_write(rt2x00dev, 86, 0x00); + rt2800_bbp_write(rt2x00dev, 91, 0x04); + rt2800_bbp_write(rt2x00dev, 92, 0x00); + rt2800_bbp_write(rt2x00dev, 103, 0x00); + rt2800_bbp_write(rt2x00dev, 105, 0x05); + + if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) { + rt2800_bbp_write(rt2x00dev, 69, 0x16); + rt2800_bbp_write(rt2x00dev, 73, 0x12); + } + + if (rt2x00_rev(&rt2x00dev->chip) > RT2860D_VERSION) + rt2800_bbp_write(rt2x00dev, 84, 0x19); + + if (rt2x00_intf_is_usb(rt2x00dev) && + rt2x00_rev(&rt2x00dev->chip) == RT3070_VERSION) { + rt2800_bbp_write(rt2x00dev, 70, 0x0a); + rt2800_bbp_write(rt2x00dev, 84, 0x99); + rt2800_bbp_write(rt2x00dev, 105, 0x05); + } + + if (rt2x00_intf_is_pci(rt2x00dev) && + rt2x00_rt(&rt2x00dev->chip, RT3052)) { + rt2800_bbp_write(rt2x00dev, 31, 0x08); + rt2800_bbp_write(rt2x00dev, 78, 0x0e); + rt2800_bbp_write(rt2x00dev, 80, 0x08); + } + + for (i = 0; i < EEPROM_BBP_SIZE; i++) { + rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i, &eeprom); + + if (eeprom != 0xffff && eeprom != 0x0000) { + reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID); + value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE); + rt2800_bbp_write(rt2x00dev, reg_id, value); + } + } + + return 0; +} +EXPORT_SYMBOL_GPL(rt2800_init_bbp); + +static u8 rt2800_init_rx_filter(struct rt2x00_dev *rt2x00dev, + bool bw40, u8 rfcsr24, u8 filter_target) +{ + unsigned int i; + u8 bbp; + u8 rfcsr; + u8 passband; + u8 stopband; + u8 overtuned = 0; + + rt2800_rfcsr_write(rt2x00dev, 24, rfcsr24); + + rt2800_bbp_read(rt2x00dev, 4, &bbp); + rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * bw40); + rt2800_bbp_write(rt2x00dev, 4, bbp); + + rt2800_rfcsr_read(rt2x00dev, 22, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 1); + rt2800_rfcsr_write(rt2x00dev, 22, rfcsr); + + /* + * Set power & frequency of passband test tone + */ + rt2800_bbp_write(rt2x00dev, 24, 0); + + for (i = 0; i < 100; i++) { + rt2800_bbp_write(rt2x00dev, 25, 0x90); + msleep(1); + + rt2800_bbp_read(rt2x00dev, 55, &passband); + if (passband) + break; + } + + /* + * Set power & frequency of stopband test tone + */ + rt2800_bbp_write(rt2x00dev, 24, 0x06); + + for (i = 0; i < 100; i++) { + rt2800_bbp_write(rt2x00dev, 25, 0x90); + msleep(1); + + rt2800_bbp_read(rt2x00dev, 55, &stopband); + + if ((passband - stopband) <= filter_target) { + rfcsr24++; + overtuned += ((passband - stopband) == filter_target); + } else + break; + + rt2800_rfcsr_write(rt2x00dev, 24, rfcsr24); + } + + rfcsr24 -= !!overtuned; + + rt2800_rfcsr_write(rt2x00dev, 24, rfcsr24); + return rfcsr24; +} + +int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev) +{ + u8 rfcsr; + u8 bbp; + + if (rt2x00_intf_is_usb(rt2x00dev) && + rt2x00_rev(&rt2x00dev->chip) != RT3070_VERSION) + return 0; + + if (rt2x00_intf_is_pci(rt2x00dev)) { + if (!rt2x00_rf(&rt2x00dev->chip, RF3020) && + !rt2x00_rf(&rt2x00dev->chip, RF3021) && + !rt2x00_rf(&rt2x00dev->chip, RF3022)) + return 0; + } + + /* + * Init RF calibration. + */ + rt2800_rfcsr_read(rt2x00dev, 30, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 1); + rt2800_rfcsr_write(rt2x00dev, 30, rfcsr); + msleep(1); + rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 0); + rt2800_rfcsr_write(rt2x00dev, 30, rfcsr); + + if (rt2x00_intf_is_usb(rt2x00dev)) { + rt2800_rfcsr_write(rt2x00dev, 4, 0x40); + rt2800_rfcsr_write(rt2x00dev, 5, 0x03); + rt2800_rfcsr_write(rt2x00dev, 6, 0x02); + rt2800_rfcsr_write(rt2x00dev, 7, 0x70); + rt2800_rfcsr_write(rt2x00dev, 9, 0x0f); + rt2800_rfcsr_write(rt2x00dev, 10, 0x71); + rt2800_rfcsr_write(rt2x00dev, 11, 0x21); + rt2800_rfcsr_write(rt2x00dev, 12, 0x7b); + rt2800_rfcsr_write(rt2x00dev, 14, 0x90); + rt2800_rfcsr_write(rt2x00dev, 15, 0x58); + rt2800_rfcsr_write(rt2x00dev, 16, 0xb3); + rt2800_rfcsr_write(rt2x00dev, 17, 0x92); + rt2800_rfcsr_write(rt2x00dev, 18, 0x2c); + rt2800_rfcsr_write(rt2x00dev, 19, 0x02); + rt2800_rfcsr_write(rt2x00dev, 20, 0xba); + rt2800_rfcsr_write(rt2x00dev, 21, 0xdb); + rt2800_rfcsr_write(rt2x00dev, 24, 0x16); + rt2800_rfcsr_write(rt2x00dev, 25, 0x01); + rt2800_rfcsr_write(rt2x00dev, 27, 0x03); + rt2800_rfcsr_write(rt2x00dev, 29, 0x1f); + } else if (rt2x00_intf_is_pci(rt2x00dev)) { + rt2800_rfcsr_write(rt2x00dev, 0, 0x50); + rt2800_rfcsr_write(rt2x00dev, 1, 0x01); + rt2800_rfcsr_write(rt2x00dev, 2, 0xf7); + rt2800_rfcsr_write(rt2x00dev, 3, 0x75); + rt2800_rfcsr_write(rt2x00dev, 4, 0x40); + rt2800_rfcsr_write(rt2x00dev, 5, 0x03); + rt2800_rfcsr_write(rt2x00dev, 6, 0x02); + rt2800_rfcsr_write(rt2x00dev, 7, 0x50); + rt2800_rfcsr_write(rt2x00dev, 8, 0x39); + rt2800_rfcsr_write(rt2x00dev, 9, 0x0f); + rt2800_rfcsr_write(rt2x00dev, 10, 0x60); + rt2800_rfcsr_write(rt2x00dev, 11, 0x21); + rt2800_rfcsr_write(rt2x00dev, 12, 0x75); + rt2800_rfcsr_write(rt2x00dev, 13, 0x75); + rt2800_rfcsr_write(rt2x00dev, 14, 0x90); + rt2800_rfcsr_write(rt2x00dev, 15, 0x58); + rt2800_rfcsr_write(rt2x00dev, 16, 0xb3); + rt2800_rfcsr_write(rt2x00dev, 17, 0x92); + rt2800_rfcsr_write(rt2x00dev, 18, 0x2c); + rt2800_rfcsr_write(rt2x00dev, 19, 0x02); + rt2800_rfcsr_write(rt2x00dev, 20, 0xba); + rt2800_rfcsr_write(rt2x00dev, 21, 0xdb); + rt2800_rfcsr_write(rt2x00dev, 22, 0x00); + rt2800_rfcsr_write(rt2x00dev, 23, 0x31); + rt2800_rfcsr_write(rt2x00dev, 24, 0x08); + rt2800_rfcsr_write(rt2x00dev, 25, 0x01); + rt2800_rfcsr_write(rt2x00dev, 26, 0x25); + rt2800_rfcsr_write(rt2x00dev, 27, 0x23); + rt2800_rfcsr_write(rt2x00dev, 28, 0x13); + rt2800_rfcsr_write(rt2x00dev, 29, 0x83); + } + + /* + * Set RX Filter calibration for 20MHz and 40MHz + */ + rt2x00dev->calibration[0] = + rt2800_init_rx_filter(rt2x00dev, false, 0x07, 0x16); + rt2x00dev->calibration[1] = + rt2800_init_rx_filter(rt2x00dev, true, 0x27, 0x19); + + /* + * Set back to initial state + */ + rt2800_bbp_write(rt2x00dev, 24, 0); + + rt2800_rfcsr_read(rt2x00dev, 22, &rfcsr); + rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 0); + rt2800_rfcsr_write(rt2x00dev, 22, rfcsr); + + /* + * set BBP back to BW20 + */ + rt2800_bbp_read(rt2x00dev, 4, &bbp); + rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 0); + rt2800_bbp_write(rt2x00dev, 4, bbp); + + return 0; +} +EXPORT_SYMBOL_GPL(rt2800_init_rfcsr); + +/* + * IEEE80211 stack callback functions. + */ +static void rt2800_get_tkip_seq(struct ieee80211_hw *hw, u8 hw_key_idx, + u32 *iv32, u16 *iv16) +{ + struct rt2x00_dev *rt2x00dev = hw->priv; + struct mac_iveiv_entry iveiv_entry; + u32 offset; + + offset = MAC_IVEIV_ENTRY(hw_key_idx); + rt2800_register_multiread(rt2x00dev, offset, + &iveiv_entry, sizeof(iveiv_entry)); + + memcpy(&iveiv_entry.iv[0], iv16, sizeof(iv16)); + memcpy(&iveiv_entry.iv[4], iv32, sizeof(iv32)); +} + +static int rt2800_set_rts_threshold(struct ieee80211_hw *hw, u32 value) +{ + struct rt2x00_dev *rt2x00dev = hw->priv; + u32 reg; + bool enabled = (value < IEEE80211_MAX_RTS_THRESHOLD); + + rt2800_register_read(rt2x00dev, TX_RTS_CFG, ®); + rt2x00_set_field32(®, TX_RTS_CFG_RTS_THRES, value); + rt2800_register_write(rt2x00dev, TX_RTS_CFG, reg); + + rt2800_register_read(rt2x00dev, CCK_PROT_CFG, ®); + rt2x00_set_field32(®, CCK_PROT_CFG_RTS_TH_EN, enabled); + rt2800_register_write(rt2x00dev, CCK_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, OFDM_PROT_CFG, ®); + rt2x00_set_field32(®, OFDM_PROT_CFG_RTS_TH_EN, enabled); + rt2800_register_write(rt2x00dev, OFDM_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, MM20_PROT_CFG, ®); + rt2x00_set_field32(®, MM20_PROT_CFG_RTS_TH_EN, enabled); + rt2800_register_write(rt2x00dev, MM20_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, MM40_PROT_CFG, ®); + rt2x00_set_field32(®, MM40_PROT_CFG_RTS_TH_EN, enabled); + rt2800_register_write(rt2x00dev, MM40_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, GF20_PROT_CFG, ®); + rt2x00_set_field32(®, GF20_PROT_CFG_RTS_TH_EN, enabled); + rt2800_register_write(rt2x00dev, GF20_PROT_CFG, reg); + + rt2800_register_read(rt2x00dev, GF40_PROT_CFG, ®); + rt2x00_set_field32(®, GF40_PROT_CFG_RTS_TH_EN, enabled); + rt2800_register_write(rt2x00dev, GF40_PROT_CFG, reg); + + return 0; +} + +static int rt2800_conf_tx(struct ieee80211_hw *hw, u16 queue_idx, + const struct ieee80211_tx_queue_params *params) +{ + struct rt2x00_dev *rt2x00dev = hw->priv; + struct data_queue *queue; + struct rt2x00_field32 field; + int retval; + u32 reg; + u32 offset; + + /* + * First pass the configuration through rt2x00lib, that will + * update the queue settings and validate the input. After that + * we are free to update the registers based on the value + * in the queue parameter. + */ + retval = rt2x00mac_conf_tx(hw, queue_idx, params); + if (retval) + return retval; + + /* + * We only need to perform additional register initialization + * for WMM queues/ + */ + if (queue_idx >= 4) + return 0; + + queue = rt2x00queue_get_queue(rt2x00dev, queue_idx); + + /* Update WMM TXOP register */ + offset = WMM_TXOP0_CFG + (sizeof(u32) * (!!(queue_idx & 2))); + field.bit_offset = (queue_idx & 1) * 16; + field.bit_mask = 0xffff << field.bit_offset; + + rt2800_register_read(rt2x00dev, offset, ®); + rt2x00_set_field32(®, field, queue->txop); + rt2800_register_write(rt2x00dev, offset, reg); + + /* Update WMM registers */ + field.bit_offset = queue_idx * 4; + field.bit_mask = 0xf << field.bit_offset; + + rt2800_register_read(rt2x00dev, WMM_AIFSN_CFG, ®); + rt2x00_set_field32(®, field, queue->aifs); + rt2800_register_write(rt2x00dev, WMM_AIFSN_CFG, reg); + + rt2800_register_read(rt2x00dev, WMM_CWMIN_CFG, ®); + rt2x00_set_field32(®, field, queue->cw_min); + rt2800_register_write(rt2x00dev, WMM_CWMIN_CFG, reg); + + rt2800_register_read(rt2x00dev, WMM_CWMAX_CFG, ®); + rt2x00_set_field32(®, field, queue->cw_max); + rt2800_register_write(rt2x00dev, WMM_CWMAX_CFG, reg); + + /* Update EDCA registers */ + offset = EDCA_AC0_CFG + (sizeof(u32) * queue_idx); + + rt2800_register_read(rt2x00dev, offset, ®); + rt2x00_set_field32(®, EDCA_AC0_CFG_TX_OP, queue->txop); + rt2x00_set_field32(®, EDCA_AC0_CFG_AIFSN, queue->aifs); + rt2x00_set_field32(®, EDCA_AC0_CFG_CWMIN, queue->cw_min); + rt2x00_set_field32(®, EDCA_AC0_CFG_CWMAX, queue->cw_max); + rt2800_register_write(rt2x00dev, offset, reg); + + return 0; +} + +static u64 rt2800_get_tsf(struct ieee80211_hw *hw) +{ + struct rt2x00_dev *rt2x00dev = hw->priv; + u64 tsf; + u32 reg; + + rt2800_register_read(rt2x00dev, TSF_TIMER_DW1, ®); + tsf = (u64) rt2x00_get_field32(reg, TSF_TIMER_DW1_HIGH_WORD) << 32; + rt2800_register_read(rt2x00dev, TSF_TIMER_DW0, ®); + tsf |= rt2x00_get_field32(reg, TSF_TIMER_DW0_LOW_WORD); + + return tsf; +} + +const struct ieee80211_ops rt2800_mac80211_ops = { + .tx = rt2x00mac_tx, + .start = rt2x00mac_start, + .stop = rt2x00mac_stop, + .add_interface = rt2x00mac_add_interface, + .remove_interface = rt2x00mac_remove_interface, + .config = rt2x00mac_config, + .configure_filter = rt2x00mac_configure_filter, + .set_tim = rt2x00mac_set_tim, + .set_key = rt2x00mac_set_key, + .get_stats = rt2x00mac_get_stats, + .get_tkip_seq = rt2800_get_tkip_seq, + .set_rts_threshold = rt2800_set_rts_threshold, + .bss_info_changed = rt2x00mac_bss_info_changed, + .conf_tx = rt2800_conf_tx, + .get_tx_stats = rt2x00mac_get_tx_stats, + .get_tsf = rt2800_get_tsf, + .rfkill_poll = rt2x00mac_rfkill_poll, +}; +EXPORT_SYMBOL_GPL(rt2800_mac80211_ops); diff --git a/drivers/net/wireless/rt2x00/rt2800lib.h b/drivers/net/wireless/rt2x00/rt2800lib.h new file mode 100644 index 0000000..5eea8fc --- /dev/null +++ b/drivers/net/wireless/rt2x00/rt2800lib.h @@ -0,0 +1,134 @@ +/* + Copyright (C) 2009 Bartlomiej Zolnierkiewicz + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the + Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef RT2800LIB_H +#define RT2800LIB_H + +struct rt2800_ops { + void (*register_read)(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, u32 *value); + void (*register_write)(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, u32 value); + void (*register_write_lock)(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, u32 value); + + void (*register_multiread)(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + void *value, const u32 length); + void (*register_multiwrite)(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const void *value, const u32 length); + + int (*regbusy_read)(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const struct rt2x00_field32 field, u32 *reg); +}; + +static inline void rt2800_register_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u32 *value) +{ + const struct rt2800_ops *rt2800ops = rt2x00dev->priv; + + rt2800ops->register_read(rt2x00dev, offset, value); +} + +static inline void rt2800_register_write(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u32 value) +{ + const struct rt2800_ops *rt2800ops = rt2x00dev->priv; + + rt2800ops->register_write(rt2x00dev, offset, value); +} + +static inline void rt2800_register_write_lock(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u32 value) +{ + const struct rt2800_ops *rt2800ops = rt2x00dev->priv; + + rt2800ops->register_write_lock(rt2x00dev, offset, value); +} + +static inline void rt2800_register_multiread(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + void *value, const u32 length) +{ + const struct rt2800_ops *rt2800ops = rt2x00dev->priv; + + rt2800ops->register_multiread(rt2x00dev, offset, value, length); +} + +static inline void rt2800_register_multiwrite(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const void *value, + const u32 length) +{ + const struct rt2800_ops *rt2800ops = rt2x00dev->priv; + + rt2800ops->register_multiwrite(rt2x00dev, offset, value, length); +} + +static inline int rt2800_regbusy_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const struct rt2x00_field32 field, + u32 *reg) +{ + const struct rt2800_ops *rt2800ops = rt2x00dev->priv; + + return rt2800ops->regbusy_read(rt2x00dev, offset, field, reg); +} + +void rt2800_mcu_request(struct rt2x00_dev *rt2x00dev, + const u8 command, const u8 token, + const u8 arg0, const u8 arg1); + +extern const struct rt2x00debug rt2800_rt2x00debug; + +int rt2800_rfkill_poll(struct rt2x00_dev *rt2x00dev); +void rt2800_init_led(struct rt2x00_dev *rt2x00dev, + struct rt2x00_led *led, enum led_type type); +int rt2800_config_shared_key(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key); +int rt2800_config_pairwise_key(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key); +void rt2800_config_filter(struct rt2x00_dev *rt2x00dev, + const unsigned int filter_flags); +void rt2800_config_intf(struct rt2x00_dev *rt2x00dev, struct rt2x00_intf *intf, + struct rt2x00intf_conf *conf, const unsigned int flags); +void rt2800_config_erp(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_erp *erp); +void rt2800_config_ant(struct rt2x00_dev *rt2x00dev, struct antenna_setup *ant); +void rt2800_config(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf, + const unsigned int flags); +void rt2800_link_stats(struct rt2x00_dev *rt2x00dev, struct link_qual *qual); +void rt2800_reset_tuner(struct rt2x00_dev *rt2x00dev, struct link_qual *qual); +void rt2800_link_tuner(struct rt2x00_dev *rt2x00dev, struct link_qual *qual, + const u32 count); + +int rt2800_init_registers(struct rt2x00_dev *rt2x00dev); +int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev); +int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev); + +extern const struct ieee80211_ops rt2800_mac80211_ops; + +#endif /* RT2800LIB_H */ diff --git a/drivers/net/wireless/rt2x00/rt2800pci.c b/drivers/net/wireless/rt2x00/rt2800pci.c index be81788..3c5b875 100644 --- a/drivers/net/wireless/rt2x00/rt2800pci.c +++ b/drivers/net/wireless/rt2x00/rt2800pci.c @@ -37,6 +37,8 @@ #include "rt2x00.h" #include "rt2x00pci.h" #include "rt2x00soc.h" +#include "rt2800lib.h" +#include "rt2800.h" #include "rt2800pci.h" #ifdef CONFIG_RT2800PCI_PCI_MODULE @@ -54,205 +56,13 @@ static int modparam_nohwcrypt = 1; module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO); MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); -/* - * Register access. - * BBP and RF register require indirect register access, - * and use the CSR registers PHY_CSR3 and PHY_CSR4 to achieve this. - * These indirect registers work with busy bits, - * and we will try maximal REGISTER_BUSY_COUNT times to access - * the register while taking a REGISTER_BUSY_DELAY us delay - * between each attampt. When the busy bit is still set at that time, - * the access attempt is considered to have failed, - * and we will print an error. - */ -#define WAIT_FOR_BBP(__dev, __reg) \ - rt2x00pci_regbusy_read((__dev), BBP_CSR_CFG, BBP_CSR_CFG_BUSY, (__reg)) -#define WAIT_FOR_RFCSR(__dev, __reg) \ - rt2x00pci_regbusy_read((__dev), RF_CSR_CFG, RF_CSR_CFG_BUSY, (__reg)) -#define WAIT_FOR_RF(__dev, __reg) \ - rt2x00pci_regbusy_read((__dev), RF_CSR_CFG0, RF_CSR_CFG0_BUSY, (__reg)) -#define WAIT_FOR_MCU(__dev, __reg) \ - rt2x00pci_regbusy_read((__dev), H2M_MAILBOX_CSR, \ - H2M_MAILBOX_CSR_OWNER, (__reg)) - -static void rt2800pci_bbp_write(struct rt2x00_dev *rt2x00dev, - const unsigned int word, const u8 value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the BBP becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_BBP(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, BBP_CSR_CFG_VALUE, value); - rt2x00_set_field32(®, BBP_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, BBP_CSR_CFG_BUSY, 1); - rt2x00_set_field32(®, BBP_CSR_CFG_READ_CONTROL, 0); - rt2x00_set_field32(®, BBP_CSR_CFG_BBP_RW_MODE, 1); - - rt2x00pci_register_write(rt2x00dev, BBP_CSR_CFG, reg); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800pci_bbp_read(struct rt2x00_dev *rt2x00dev, - const unsigned int word, u8 *value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the BBP becomes available, afterwards we - * can safely write the read request into the register. - * After the data has been written, we wait until hardware - * returns the correct value, if at any time the register - * doesn't become available in time, reg will be 0xffffffff - * which means we return 0xff to the caller. - */ - if (WAIT_FOR_BBP(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, BBP_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, BBP_CSR_CFG_BUSY, 1); - rt2x00_set_field32(®, BBP_CSR_CFG_READ_CONTROL, 1); - rt2x00_set_field32(®, BBP_CSR_CFG_BBP_RW_MODE, 1); - - rt2x00pci_register_write(rt2x00dev, BBP_CSR_CFG, reg); - - WAIT_FOR_BBP(rt2x00dev, ®); - } - - *value = rt2x00_get_field32(reg, BBP_CSR_CFG_VALUE); - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800pci_rfcsr_write(struct rt2x00_dev *rt2x00dev, - const unsigned int word, const u8 value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the RFCSR becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_RFCSR(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, RF_CSR_CFG_DATA, value); - rt2x00_set_field32(®, RF_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, RF_CSR_CFG_WRITE, 1); - rt2x00_set_field32(®, RF_CSR_CFG_BUSY, 1); - - rt2x00pci_register_write(rt2x00dev, RF_CSR_CFG, reg); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800pci_rfcsr_read(struct rt2x00_dev *rt2x00dev, - const unsigned int word, u8 *value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the RFCSR becomes available, afterwards we - * can safely write the read request into the register. - * After the data has been written, we wait until hardware - * returns the correct value, if at any time the register - * doesn't become available in time, reg will be 0xffffffff - * which means we return 0xff to the caller. - */ - if (WAIT_FOR_RFCSR(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, RF_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, RF_CSR_CFG_WRITE, 0); - rt2x00_set_field32(®, RF_CSR_CFG_BUSY, 1); - - rt2x00pci_register_write(rt2x00dev, RF_CSR_CFG, reg); - - WAIT_FOR_RFCSR(rt2x00dev, ®); - } - - *value = rt2x00_get_field32(reg, RF_CSR_CFG_DATA); - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800pci_rf_write(struct rt2x00_dev *rt2x00dev, - const unsigned int word, const u32 value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the RF becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_RF(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, RF_CSR_CFG0_REG_VALUE_BW, value); - rt2x00_set_field32(®, RF_CSR_CFG0_STANDBYMODE, 0); - rt2x00_set_field32(®, RF_CSR_CFG0_SEL, 0); - rt2x00_set_field32(®, RF_CSR_CFG0_BUSY, 1); - - rt2x00pci_register_write(rt2x00dev, RF_CSR_CFG0, reg); - rt2x00_rf_write(rt2x00dev, word, value); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800pci_mcu_request(struct rt2x00_dev *rt2x00dev, - const u8 command, const u8 token, - const u8 arg0, const u8 arg1) -{ - u32 reg; - - /* - * RT2880 and RT3052 don't support MCU requests. - */ - if (rt2x00_rt(&rt2x00dev->chip, RT2880) || - rt2x00_rt(&rt2x00dev->chip, RT3052)) - return; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the MCU becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_MCU(rt2x00dev, ®)) { - rt2x00_set_field32(®, H2M_MAILBOX_CSR_OWNER, 1); - rt2x00_set_field32(®, H2M_MAILBOX_CSR_CMD_TOKEN, token); - rt2x00_set_field32(®, H2M_MAILBOX_CSR_ARG0, arg0); - rt2x00_set_field32(®, H2M_MAILBOX_CSR_ARG1, arg1); - rt2x00pci_register_write(rt2x00dev, H2M_MAILBOX_CSR, reg); - - reg = 0; - rt2x00_set_field32(®, HOST_CMD_CSR_HOST_COMMAND, command); - rt2x00pci_register_write(rt2x00dev, HOST_CMD_CSR, reg); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - static void rt2800pci_mcu_status(struct rt2x00_dev *rt2x00dev, const u8 token) { unsigned int i; u32 reg; for (i = 0; i < 200; i++) { - rt2x00pci_register_read(rt2x00dev, H2M_MAILBOX_CID, ®); + rt2800_register_read(rt2x00dev, H2M_MAILBOX_CID, ®); if ((rt2x00_get_field32(reg, H2M_MAILBOX_CID_CMD0) == token) || (rt2x00_get_field32(reg, H2M_MAILBOX_CID_CMD1) == token) || @@ -266,8 +76,8 @@ static void rt2800pci_mcu_status(struct rt2x00_dev *rt2x00dev, const u8 token) if (i == 200) ERROR(rt2x00dev, "MCU request failed, no response from hardware\n"); - rt2x00pci_register_write(rt2x00dev, H2M_MAILBOX_STATUS, ~0); - rt2x00pci_register_write(rt2x00dev, H2M_MAILBOX_CID, ~0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_STATUS, ~0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_CID, ~0); } #ifdef CONFIG_RT2800PCI_WISOC @@ -289,7 +99,7 @@ static void rt2800pci_eepromregister_read(struct eeprom_93cx6 *eeprom) struct rt2x00_dev *rt2x00dev = eeprom->data; u32 reg; - rt2x00pci_register_read(rt2x00dev, E2PROM_CSR, ®); + rt2800_register_read(rt2x00dev, E2PROM_CSR, ®); eeprom->reg_data_in = !!rt2x00_get_field32(reg, E2PROM_CSR_DATA_IN); eeprom->reg_data_out = !!rt2x00_get_field32(reg, E2PROM_CSR_DATA_OUT); @@ -311,7 +121,7 @@ static void rt2800pci_eepromregister_write(struct eeprom_93cx6 *eeprom) rt2x00_set_field32(®, E2PROM_CSR_CHIP_SELECT, !!eeprom->reg_chip_select); - rt2x00pci_register_write(rt2x00dev, E2PROM_CSR, reg); + rt2800_register_write(rt2x00dev, E2PROM_CSR, reg); } static void rt2800pci_read_eeprom_pci(struct rt2x00_dev *rt2x00dev) @@ -319,7 +129,7 @@ static void rt2800pci_read_eeprom_pci(struct rt2x00_dev *rt2x00dev) struct eeprom_93cx6 eeprom; u32 reg; - rt2x00pci_register_read(rt2x00dev, E2PROM_CSR, ®); + rt2800_register_read(rt2x00dev, E2PROM_CSR, ®); eeprom.data = rt2x00dev; eeprom.register_read = rt2800pci_eepromregister_read; @@ -340,23 +150,23 @@ static void rt2800pci_efuse_read(struct rt2x00_dev *rt2x00dev, { u32 reg; - rt2x00pci_register_read(rt2x00dev, EFUSE_CTRL, ®); + rt2800_register_read(rt2x00dev, EFUSE_CTRL, ®); rt2x00_set_field32(®, EFUSE_CTRL_ADDRESS_IN, i); rt2x00_set_field32(®, EFUSE_CTRL_MODE, 0); rt2x00_set_field32(®, EFUSE_CTRL_KICK, 1); - rt2x00pci_register_write(rt2x00dev, EFUSE_CTRL, reg); + rt2800_register_write(rt2x00dev, EFUSE_CTRL, reg); /* Wait until the EEPROM has been loaded */ - rt2x00pci_regbusy_read(rt2x00dev, EFUSE_CTRL, EFUSE_CTRL_KICK, ®); + rt2800_regbusy_read(rt2x00dev, EFUSE_CTRL, EFUSE_CTRL_KICK, ®); /* Apparently the data is read from end to start */ - rt2x00pci_register_read(rt2x00dev, EFUSE_DATA3, + rt2800_register_read(rt2x00dev, EFUSE_DATA3, (u32 *)&rt2x00dev->eeprom[i]); - rt2x00pci_register_read(rt2x00dev, EFUSE_DATA2, + rt2800_register_read(rt2x00dev, EFUSE_DATA2, (u32 *)&rt2x00dev->eeprom[i + 2]); - rt2x00pci_register_read(rt2x00dev, EFUSE_DATA1, + rt2800_register_read(rt2x00dev, EFUSE_DATA1, (u32 *)&rt2x00dev->eeprom[i + 4]); - rt2x00pci_register_read(rt2x00dev, EFUSE_DATA0, + rt2800_register_read(rt2x00dev, EFUSE_DATA0, (u32 *)&rt2x00dev->eeprom[i + 6]); } @@ -377,829 +187,6 @@ static inline void rt2800pci_read_eeprom_efuse(struct rt2x00_dev *rt2x00dev) } #endif /* CONFIG_RT2800PCI_PCI */ -#ifdef CONFIG_RT2X00_LIB_DEBUGFS -static const struct rt2x00debug rt2800pci_rt2x00debug = { - .owner = THIS_MODULE, - .csr = { - .read = rt2x00pci_register_read, - .write = rt2x00pci_register_write, - .flags = RT2X00DEBUGFS_OFFSET, - .word_base = CSR_REG_BASE, - .word_size = sizeof(u32), - .word_count = CSR_REG_SIZE / sizeof(u32), - }, - .eeprom = { - .read = rt2x00_eeprom_read, - .write = rt2x00_eeprom_write, - .word_base = EEPROM_BASE, - .word_size = sizeof(u16), - .word_count = EEPROM_SIZE / sizeof(u16), - }, - .bbp = { - .read = rt2800pci_bbp_read, - .write = rt2800pci_bbp_write, - .word_base = BBP_BASE, - .word_size = sizeof(u8), - .word_count = BBP_SIZE / sizeof(u8), - }, - .rf = { - .read = rt2x00_rf_read, - .write = rt2800pci_rf_write, - .word_base = RF_BASE, - .word_size = sizeof(u32), - .word_count = RF_SIZE / sizeof(u32), - }, -}; -#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ - -static int rt2800pci_rfkill_poll(struct rt2x00_dev *rt2x00dev) -{ - u32 reg; - - rt2x00pci_register_read(rt2x00dev, GPIO_CTRL_CFG, ®); - return rt2x00_get_field32(reg, GPIO_CTRL_CFG_BIT2); -} - -#ifdef CONFIG_RT2X00_LIB_LEDS -static void rt2800pci_brightness_set(struct led_classdev *led_cdev, - enum led_brightness brightness) -{ - struct rt2x00_led *led = - container_of(led_cdev, struct rt2x00_led, led_dev); - unsigned int enabled = brightness != LED_OFF; - unsigned int bg_mode = - (enabled && led->rt2x00dev->curr_band == IEEE80211_BAND_2GHZ); - unsigned int polarity = - rt2x00_get_field16(led->rt2x00dev->led_mcu_reg, - EEPROM_FREQ_LED_POLARITY); - unsigned int ledmode = - rt2x00_get_field16(led->rt2x00dev->led_mcu_reg, - EEPROM_FREQ_LED_MODE); - - if (led->type == LED_TYPE_RADIO) { - rt2800pci_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode, - enabled ? 0x20 : 0); - } else if (led->type == LED_TYPE_ASSOC) { - rt2800pci_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode, - enabled ? (bg_mode ? 0x60 : 0xa0) : 0x20); - } else if (led->type == LED_TYPE_QUALITY) { - /* - * The brightness is divided into 6 levels (0 - 5), - * The specs tell us the following levels: - * 0, 1 ,3, 7, 15, 31 - * to determine the level in a simple way we can simply - * work with bitshifting: - * (1 << level) - 1 - */ - rt2800pci_mcu_request(led->rt2x00dev, MCU_LED_STRENGTH, 0xff, - (1 << brightness / (LED_FULL / 6)) - 1, - polarity); - } -} - -static int rt2800pci_blink_set(struct led_classdev *led_cdev, - unsigned long *delay_on, - unsigned long *delay_off) -{ - struct rt2x00_led *led = - container_of(led_cdev, struct rt2x00_led, led_dev); - u32 reg; - - rt2x00pci_register_read(led->rt2x00dev, LED_CFG, ®); - rt2x00_set_field32(®, LED_CFG_ON_PERIOD, *delay_on); - rt2x00_set_field32(®, LED_CFG_OFF_PERIOD, *delay_off); - rt2x00_set_field32(®, LED_CFG_SLOW_BLINK_PERIOD, 3); - rt2x00_set_field32(®, LED_CFG_R_LED_MODE, 3); - rt2x00_set_field32(®, LED_CFG_G_LED_MODE, 12); - rt2x00_set_field32(®, LED_CFG_Y_LED_MODE, 3); - rt2x00_set_field32(®, LED_CFG_LED_POLAR, 1); - rt2x00pci_register_write(led->rt2x00dev, LED_CFG, reg); - - return 0; -} - -static void rt2800pci_init_led(struct rt2x00_dev *rt2x00dev, - struct rt2x00_led *led, - enum led_type type) -{ - led->rt2x00dev = rt2x00dev; - led->type = type; - led->led_dev.brightness_set = rt2800pci_brightness_set; - led->led_dev.blink_set = rt2800pci_blink_set; - led->flags = LED_INITIALIZED; -} -#endif /* CONFIG_RT2X00_LIB_LEDS */ - -/* - * Configuration handlers. - */ -static void rt2800pci_config_wcid_attr(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_crypto *crypto, - struct ieee80211_key_conf *key) -{ - struct mac_wcid_entry wcid_entry; - struct mac_iveiv_entry iveiv_entry; - u32 offset; - u32 reg; - - offset = MAC_WCID_ATTR_ENTRY(key->hw_key_idx); - - rt2x00pci_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_KEYTAB, - !!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_CIPHER, - (crypto->cmd == SET_KEY) * crypto->cipher); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_BSS_IDX, - (crypto->cmd == SET_KEY) * crypto->bssidx); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_RX_WIUDF, crypto->cipher); - rt2x00pci_register_write(rt2x00dev, offset, reg); - - offset = MAC_IVEIV_ENTRY(key->hw_key_idx); - - memset(&iveiv_entry, 0, sizeof(iveiv_entry)); - if ((crypto->cipher == CIPHER_TKIP) || - (crypto->cipher == CIPHER_TKIP_NO_MIC) || - (crypto->cipher == CIPHER_AES)) - iveiv_entry.iv[3] |= 0x20; - iveiv_entry.iv[3] |= key->keyidx << 6; - rt2x00pci_register_multiwrite(rt2x00dev, offset, - &iveiv_entry, sizeof(iveiv_entry)); - - offset = MAC_WCID_ENTRY(key->hw_key_idx); - - memset(&wcid_entry, 0, sizeof(wcid_entry)); - if (crypto->cmd == SET_KEY) - memcpy(&wcid_entry, crypto->address, ETH_ALEN); - rt2x00pci_register_multiwrite(rt2x00dev, offset, - &wcid_entry, sizeof(wcid_entry)); -} - -static int rt2800pci_config_shared_key(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_crypto *crypto, - struct ieee80211_key_conf *key) -{ - struct hw_key_entry key_entry; - struct rt2x00_field32 field; - u32 offset; - u32 reg; - - if (crypto->cmd == SET_KEY) { - key->hw_key_idx = (4 * crypto->bssidx) + key->keyidx; - - memcpy(key_entry.key, crypto->key, - sizeof(key_entry.key)); - memcpy(key_entry.tx_mic, crypto->tx_mic, - sizeof(key_entry.tx_mic)); - memcpy(key_entry.rx_mic, crypto->rx_mic, - sizeof(key_entry.rx_mic)); - - offset = SHARED_KEY_ENTRY(key->hw_key_idx); - rt2x00pci_register_multiwrite(rt2x00dev, offset, - &key_entry, sizeof(key_entry)); - } - - /* - * The cipher types are stored over multiple registers - * starting with SHARED_KEY_MODE_BASE each word will have - * 32 bits and contains the cipher types for 2 bssidx each. - * Using the correct defines correctly will cause overhead, - * so just calculate the correct offset. - */ - field.bit_offset = 4 * (key->hw_key_idx % 8); - field.bit_mask = 0x7 << field.bit_offset; - - offset = SHARED_KEY_MODE_ENTRY(key->hw_key_idx / 8); - - rt2x00pci_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, field, - (crypto->cmd == SET_KEY) * crypto->cipher); - rt2x00pci_register_write(rt2x00dev, offset, reg); - - /* - * Update WCID information - */ - rt2800pci_config_wcid_attr(rt2x00dev, crypto, key); - - return 0; -} - -static int rt2800pci_config_pairwise_key(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_crypto *crypto, - struct ieee80211_key_conf *key) -{ - struct hw_key_entry key_entry; - u32 offset; - - if (crypto->cmd == SET_KEY) { - /* - * 1 pairwise key is possible per AID, this means that the AID - * equals our hw_key_idx. Make sure the WCID starts _after_ the - * last possible shared key entry. - */ - if (crypto->aid > (256 - 32)) - return -ENOSPC; - - key->hw_key_idx = 32 + crypto->aid; - - - memcpy(key_entry.key, crypto->key, - sizeof(key_entry.key)); - memcpy(key_entry.tx_mic, crypto->tx_mic, - sizeof(key_entry.tx_mic)); - memcpy(key_entry.rx_mic, crypto->rx_mic, - sizeof(key_entry.rx_mic)); - - offset = PAIRWISE_KEY_ENTRY(key->hw_key_idx); - rt2x00pci_register_multiwrite(rt2x00dev, offset, - &key_entry, sizeof(key_entry)); - } - - /* - * Update WCID information - */ - rt2800pci_config_wcid_attr(rt2x00dev, crypto, key); - - return 0; -} - -static void rt2800pci_config_filter(struct rt2x00_dev *rt2x00dev, - const unsigned int filter_flags) -{ - u32 reg; - - /* - * Start configuration steps. - * Note that the version error will always be dropped - * and broadcast frames will always be accepted since - * there is no filter for it at this time. - */ - rt2x00pci_register_read(rt2x00dev, RX_FILTER_CFG, ®); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CRC_ERROR, - !(filter_flags & FIF_FCSFAIL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PHY_ERROR, - !(filter_flags & FIF_PLCPFAIL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_NOT_TO_ME, - !(filter_flags & FIF_PROMISC_IN_BSS)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_NOT_MY_BSSD, 0); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_VER_ERROR, 1); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_MULTICAST, - !(filter_flags & FIF_ALLMULTI)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BROADCAST, 0); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_DUPLICATE, 1); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CF_END_ACK, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CF_END, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_ACK, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CTS, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_RTS, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PSPOLL, - !(filter_flags & FIF_PSPOLL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BA, 1); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BAR, 0); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CNTL, - !(filter_flags & FIF_CONTROL)); - rt2x00pci_register_write(rt2x00dev, RX_FILTER_CFG, reg); -} - -static void rt2800pci_config_intf(struct rt2x00_dev *rt2x00dev, - struct rt2x00_intf *intf, - struct rt2x00intf_conf *conf, - const unsigned int flags) -{ - unsigned int beacon_base; - u32 reg; - - if (flags & CONFIG_UPDATE_TYPE) { - /* - * Clear current synchronisation setup. - * For the Beacon base registers we only need to clear - * the first byte since that byte contains the VALID and OWNER - * bits which (when set to 0) will invalidate the entire beacon. - */ - beacon_base = HW_BEACON_OFFSET(intf->beacon->entry_idx); - rt2x00pci_register_write(rt2x00dev, beacon_base, 0); - - /* - * Enable synchronisation. - */ - rt2x00pci_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_SYNC, conf->sync); - rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1); - rt2x00pci_register_write(rt2x00dev, BCN_TIME_CFG, reg); - } - - if (flags & CONFIG_UPDATE_MAC) { - reg = le32_to_cpu(conf->mac[1]); - rt2x00_set_field32(®, MAC_ADDR_DW1_UNICAST_TO_ME_MASK, 0xff); - conf->mac[1] = cpu_to_le32(reg); - - rt2x00pci_register_multiwrite(rt2x00dev, MAC_ADDR_DW0, - conf->mac, sizeof(conf->mac)); - } - - if (flags & CONFIG_UPDATE_BSSID) { - reg = le32_to_cpu(conf->bssid[1]); - rt2x00_set_field32(®, MAC_BSSID_DW1_BSS_ID_MASK, 0); - rt2x00_set_field32(®, MAC_BSSID_DW1_BSS_BCN_NUM, 0); - conf->bssid[1] = cpu_to_le32(reg); - - rt2x00pci_register_multiwrite(rt2x00dev, MAC_BSSID_DW0, - conf->bssid, sizeof(conf->bssid)); - } -} - -static void rt2800pci_config_erp(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_erp *erp) -{ - u32 reg; - - rt2x00pci_register_read(rt2x00dev, TX_TIMEOUT_CFG, ®); - rt2x00_set_field32(®, TX_TIMEOUT_CFG_RX_ACK_TIMEOUT, 0x20); - rt2x00pci_register_write(rt2x00dev, TX_TIMEOUT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, AUTO_RSP_CFG, ®); - rt2x00_set_field32(®, AUTO_RSP_CFG_BAC_ACK_POLICY, - !!erp->short_preamble); - rt2x00_set_field32(®, AUTO_RSP_CFG_AR_PREAMBLE, - !!erp->short_preamble); - rt2x00pci_register_write(rt2x00dev, AUTO_RSP_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, OFDM_PROT_CFG, ®); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, - erp->cts_protection ? 2 : 0); - rt2x00pci_register_write(rt2x00dev, OFDM_PROT_CFG, reg); - - rt2x00pci_register_write(rt2x00dev, LEGACY_BASIC_RATE, - erp->basic_rates); - rt2x00pci_register_write(rt2x00dev, HT_BASIC_RATE, 0x00008003); - - rt2x00pci_register_read(rt2x00dev, BKOFF_SLOT_CFG, ®); - rt2x00_set_field32(®, BKOFF_SLOT_CFG_SLOT_TIME, erp->slot_time); - rt2x00_set_field32(®, BKOFF_SLOT_CFG_CC_DELAY_TIME, 2); - rt2x00pci_register_write(rt2x00dev, BKOFF_SLOT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, XIFS_TIME_CFG, ®); - rt2x00_set_field32(®, XIFS_TIME_CFG_CCKM_SIFS_TIME, erp->sifs); - rt2x00_set_field32(®, XIFS_TIME_CFG_OFDM_SIFS_TIME, erp->sifs); - rt2x00_set_field32(®, XIFS_TIME_CFG_OFDM_XIFS_TIME, 4); - rt2x00_set_field32(®, XIFS_TIME_CFG_EIFS, erp->eifs); - rt2x00_set_field32(®, XIFS_TIME_CFG_BB_RXEND_ENABLE, 1); - rt2x00pci_register_write(rt2x00dev, XIFS_TIME_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_INTERVAL, - erp->beacon_int * 16); - rt2x00pci_register_write(rt2x00dev, BCN_TIME_CFG, reg); -} - -static void rt2800pci_config_ant(struct rt2x00_dev *rt2x00dev, - struct antenna_setup *ant) -{ - u8 r1; - u8 r3; - - rt2800pci_bbp_read(rt2x00dev, 1, &r1); - rt2800pci_bbp_read(rt2x00dev, 3, &r3); - - /* - * Configure the TX antenna. - */ - switch ((int)ant->tx) { - case 1: - rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 0); - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 0); - break; - case 2: - rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 2); - break; - case 3: - /* Do nothing */ - break; - } - - /* - * Configure the RX antenna. - */ - switch ((int)ant->rx) { - case 1: - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 0); - break; - case 2: - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 1); - break; - case 3: - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 2); - break; - } - - rt2800pci_bbp_write(rt2x00dev, 3, r3); - rt2800pci_bbp_write(rt2x00dev, 1, r1); -} - -static void rt2800pci_config_lna_gain(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf) -{ - u16 eeprom; - short lna_gain; - - if (libconf->rf.channel <= 14) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_LNA, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_LNA_BG); - } else if (libconf->rf.channel <= 64) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_LNA, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_LNA_A0); - } else if (libconf->rf.channel <= 128) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_BG2, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_RSSI_BG2_LNA_A1); - } else { - rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_A2, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_RSSI_A2_LNA_A2); - } - - rt2x00dev->lna_gain = lna_gain; -} - -static void rt2800pci_config_channel_rt2x(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf, - struct rf_channel *rf, - struct channel_info *info) -{ - rt2x00_set_field32(&rf->rf4, RF4_FREQ_OFFSET, rt2x00dev->freq_offset); - - if (rt2x00dev->default_ant.tx == 1) - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_TX1, 1); - - if (rt2x00dev->default_ant.rx == 1) { - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX1, 1); - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1); - } else if (rt2x00dev->default_ant.rx == 2) - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1); - - if (rf->channel > 14) { - /* - * When TX power is below 0, we should increase it by 7 to - * make it a positive value (Minumum value is -7). - * However this means that values between 0 and 7 have - * double meaning, and we should set a 7DBm boost flag. - */ - rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_A_7DBM_BOOST, - (info->tx_power1 >= 0)); - - if (info->tx_power1 < 0) - info->tx_power1 += 7; - - rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_A, - TXPOWER_A_TO_DEV(info->tx_power1)); - - rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_A_7DBM_BOOST, - (info->tx_power2 >= 0)); - - if (info->tx_power2 < 0) - info->tx_power2 += 7; - - rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_A, - TXPOWER_A_TO_DEV(info->tx_power2)); - } else { - rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_G, - TXPOWER_G_TO_DEV(info->tx_power1)); - rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_G, - TXPOWER_G_TO_DEV(info->tx_power2)); - } - - rt2x00_set_field32(&rf->rf4, RF4_HT40, conf_is_ht40(conf)); - - rt2800pci_rf_write(rt2x00dev, 1, rf->rf1); - rt2800pci_rf_write(rt2x00dev, 2, rf->rf2); - rt2800pci_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); - rt2800pci_rf_write(rt2x00dev, 4, rf->rf4); - - udelay(200); - - rt2800pci_rf_write(rt2x00dev, 1, rf->rf1); - rt2800pci_rf_write(rt2x00dev, 2, rf->rf2); - rt2800pci_rf_write(rt2x00dev, 3, rf->rf3 | 0x00000004); - rt2800pci_rf_write(rt2x00dev, 4, rf->rf4); - - udelay(200); - - rt2800pci_rf_write(rt2x00dev, 1, rf->rf1); - rt2800pci_rf_write(rt2x00dev, 2, rf->rf2); - rt2800pci_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); - rt2800pci_rf_write(rt2x00dev, 4, rf->rf4); -} - -static void rt2800pci_config_channel_rt3x(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf, - struct rf_channel *rf, - struct channel_info *info) -{ - u8 rfcsr; - - rt2800pci_rfcsr_write(rt2x00dev, 2, rf->rf1); - rt2800pci_rfcsr_write(rt2x00dev, 2, rf->rf3); - - rt2800pci_rfcsr_read(rt2x00dev, 6, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR6_R, rf->rf2); - rt2800pci_rfcsr_write(rt2x00dev, 6, rfcsr); - - rt2800pci_rfcsr_read(rt2x00dev, 12, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR12_TX_POWER, - TXPOWER_G_TO_DEV(info->tx_power1)); - rt2800pci_rfcsr_write(rt2x00dev, 12, rfcsr); - - rt2800pci_rfcsr_read(rt2x00dev, 23, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR23_FREQ_OFFSET, rt2x00dev->freq_offset); - rt2800pci_rfcsr_write(rt2x00dev, 23, rfcsr); - - rt2800pci_rfcsr_write(rt2x00dev, 24, - rt2x00dev->calibration[conf_is_ht40(conf)]); - - rt2800pci_rfcsr_read(rt2x00dev, 23, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR7_RF_TUNING, 1); - rt2800pci_rfcsr_write(rt2x00dev, 23, rfcsr); -} - -static void rt2800pci_config_channel(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf, - struct rf_channel *rf, - struct channel_info *info) -{ - u32 reg; - unsigned int tx_pin; - u8 bbp; - - if (rt2x00_rev(&rt2x00dev->chip) != RT3070_VERSION) - rt2800pci_config_channel_rt2x(rt2x00dev, conf, rf, info); - else - rt2800pci_config_channel_rt3x(rt2x00dev, conf, rf, info); - - /* - * Change BBP settings - */ - rt2800pci_bbp_write(rt2x00dev, 62, 0x37 - rt2x00dev->lna_gain); - rt2800pci_bbp_write(rt2x00dev, 63, 0x37 - rt2x00dev->lna_gain); - rt2800pci_bbp_write(rt2x00dev, 64, 0x37 - rt2x00dev->lna_gain); - rt2800pci_bbp_write(rt2x00dev, 86, 0); - - if (rf->channel <= 14) { - if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags)) { - rt2800pci_bbp_write(rt2x00dev, 82, 0x62); - rt2800pci_bbp_write(rt2x00dev, 75, 0x46); - } else { - rt2800pci_bbp_write(rt2x00dev, 82, 0x84); - rt2800pci_bbp_write(rt2x00dev, 75, 0x50); - } - } else { - rt2800pci_bbp_write(rt2x00dev, 82, 0xf2); - - if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags)) - rt2800pci_bbp_write(rt2x00dev, 75, 0x46); - else - rt2800pci_bbp_write(rt2x00dev, 75, 0x50); - } - - rt2x00pci_register_read(rt2x00dev, TX_BAND_CFG, ®); - rt2x00_set_field32(®, TX_BAND_CFG_HT40_PLUS, conf_is_ht40_plus(conf)); - rt2x00_set_field32(®, TX_BAND_CFG_A, rf->channel > 14); - rt2x00_set_field32(®, TX_BAND_CFG_BG, rf->channel <= 14); - rt2x00pci_register_write(rt2x00dev, TX_BAND_CFG, reg); - - tx_pin = 0; - - /* Turn on unused PA or LNA when not using 1T or 1R */ - if (rt2x00dev->default_ant.tx != 1) { - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A1_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G1_EN, 1); - } - - /* Turn on unused PA or LNA when not using 1T or 1R */ - if (rt2x00dev->default_ant.rx != 1) { - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A1_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G1_EN, 1); - } - - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A0_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G0_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_RFTR_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_TRSW_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G0_EN, rf->channel <= 14); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A0_EN, rf->channel > 14); - - rt2x00pci_register_write(rt2x00dev, TX_PIN_CFG, tx_pin); - - rt2800pci_bbp_read(rt2x00dev, 4, &bbp); - rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * conf_is_ht40(conf)); - rt2800pci_bbp_write(rt2x00dev, 4, bbp); - - rt2800pci_bbp_read(rt2x00dev, 3, &bbp); - rt2x00_set_field8(&bbp, BBP3_HT40_PLUS, conf_is_ht40_plus(conf)); - rt2800pci_bbp_write(rt2x00dev, 3, bbp); - - if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) { - if (conf_is_ht40(conf)) { - rt2800pci_bbp_write(rt2x00dev, 69, 0x1a); - rt2800pci_bbp_write(rt2x00dev, 70, 0x0a); - rt2800pci_bbp_write(rt2x00dev, 73, 0x16); - } else { - rt2800pci_bbp_write(rt2x00dev, 69, 0x16); - rt2800pci_bbp_write(rt2x00dev, 70, 0x08); - rt2800pci_bbp_write(rt2x00dev, 73, 0x11); - } - } - - msleep(1); -} - -static void rt2800pci_config_txpower(struct rt2x00_dev *rt2x00dev, - const int txpower) -{ - u32 reg; - u32 value = TXPOWER_G_TO_DEV(txpower); - u8 r1; - - rt2800pci_bbp_read(rt2x00dev, 1, &r1); - rt2x00_set_field8(®, BBP1_TX_POWER, 0); - rt2800pci_bbp_write(rt2x00dev, 1, r1); - - rt2x00pci_register_read(rt2x00dev, TX_PWR_CFG_0, ®); - rt2x00_set_field32(®, TX_PWR_CFG_0_1MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_2MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_55MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_11MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_6MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_9MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_12MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_18MBS, value); - rt2x00pci_register_write(rt2x00dev, TX_PWR_CFG_0, reg); - - rt2x00pci_register_read(rt2x00dev, TX_PWR_CFG_1, ®); - rt2x00_set_field32(®, TX_PWR_CFG_1_24MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_36MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_48MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_54MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS0, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS1, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS2, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS3, value); - rt2x00pci_register_write(rt2x00dev, TX_PWR_CFG_1, reg); - - rt2x00pci_register_read(rt2x00dev, TX_PWR_CFG_2, ®); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS4, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS5, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS6, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS7, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS8, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS9, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS10, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS11, value); - rt2x00pci_register_write(rt2x00dev, TX_PWR_CFG_2, reg); - - rt2x00pci_register_read(rt2x00dev, TX_PWR_CFG_3, ®); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS12, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS13, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS14, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS15, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN1, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN2, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN3, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN4, value); - rt2x00pci_register_write(rt2x00dev, TX_PWR_CFG_3, reg); - - rt2x00pci_register_read(rt2x00dev, TX_PWR_CFG_4, ®); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN5, value); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN6, value); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN7, value); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN8, value); - rt2x00pci_register_write(rt2x00dev, TX_PWR_CFG_4, reg); -} - -static void rt2800pci_config_retry_limit(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf) -{ - u32 reg; - - rt2x00pci_register_read(rt2x00dev, TX_RTY_CFG, ®); - rt2x00_set_field32(®, TX_RTY_CFG_SHORT_RTY_LIMIT, - libconf->conf->short_frame_max_tx_count); - rt2x00_set_field32(®, TX_RTY_CFG_LONG_RTY_LIMIT, - libconf->conf->long_frame_max_tx_count); - rt2x00_set_field32(®, TX_RTY_CFG_LONG_RTY_THRE, 2000); - rt2x00_set_field32(®, TX_RTY_CFG_NON_AGG_RTY_MODE, 0); - rt2x00_set_field32(®, TX_RTY_CFG_AGG_RTY_MODE, 0); - rt2x00_set_field32(®, TX_RTY_CFG_TX_AUTO_FB_ENABLE, 1); - rt2x00pci_register_write(rt2x00dev, TX_RTY_CFG, reg); -} - -static void rt2800pci_config_ps(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf) -{ - enum dev_state state = - (libconf->conf->flags & IEEE80211_CONF_PS) ? - STATE_SLEEP : STATE_AWAKE; - u32 reg; - - if (state == STATE_SLEEP) { - rt2x00pci_register_write(rt2x00dev, AUTOWAKEUP_CFG, 0); - - rt2x00pci_register_read(rt2x00dev, AUTOWAKEUP_CFG, ®); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTO_LEAD_TIME, 5); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE, - libconf->conf->listen_interval - 1); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTOWAKE, 1); - rt2x00pci_register_write(rt2x00dev, AUTOWAKEUP_CFG, reg); - - rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); - } else { - rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); - - rt2x00pci_register_read(rt2x00dev, AUTOWAKEUP_CFG, ®); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTO_LEAD_TIME, 0); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE, 0); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTOWAKE, 0); - rt2x00pci_register_write(rt2x00dev, AUTOWAKEUP_CFG, reg); - } -} - -static void rt2800pci_config(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf, - const unsigned int flags) -{ - /* Always recalculate LNA gain before changing configuration */ - rt2800pci_config_lna_gain(rt2x00dev, libconf); - - if (flags & IEEE80211_CONF_CHANGE_CHANNEL) - rt2800pci_config_channel(rt2x00dev, libconf->conf, - &libconf->rf, &libconf->channel); - if (flags & IEEE80211_CONF_CHANGE_POWER) - rt2800pci_config_txpower(rt2x00dev, libconf->conf->power_level); - if (flags & IEEE80211_CONF_CHANGE_RETRY_LIMITS) - rt2800pci_config_retry_limit(rt2x00dev, libconf); - if (flags & IEEE80211_CONF_CHANGE_PS) - rt2800pci_config_ps(rt2x00dev, libconf); -} - -/* - * Link tuning - */ -static void rt2800pci_link_stats(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual) -{ - u32 reg; - - /* - * Update FCS error count from register. - */ - rt2x00pci_register_read(rt2x00dev, RX_STA_CNT0, ®); - qual->rx_failed = rt2x00_get_field32(reg, RX_STA_CNT0_CRC_ERR); -} - -static u8 rt2800pci_get_default_vgc(struct rt2x00_dev *rt2x00dev) -{ - if (rt2x00dev->curr_band == IEEE80211_BAND_2GHZ) - return 0x2e + rt2x00dev->lna_gain; - - if (!test_bit(CONFIG_CHANNEL_HT40, &rt2x00dev->flags)) - return 0x32 + (rt2x00dev->lna_gain * 5) / 3; - else - return 0x3a + (rt2x00dev->lna_gain * 5) / 3; -} - -static inline void rt2800pci_set_vgc(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual, u8 vgc_level) -{ - if (qual->vgc_level != vgc_level) { - rt2800pci_bbp_write(rt2x00dev, 66, vgc_level); - qual->vgc_level = vgc_level; - qual->vgc_level_reg = vgc_level; - } -} - -static void rt2800pci_reset_tuner(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual) -{ - rt2800pci_set_vgc(rt2x00dev, qual, - rt2800pci_get_default_vgc(rt2x00dev)); -} - -static void rt2800pci_link_tuner(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual, const u32 count) -{ - if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) - return; - - /* - * When RSSI is better then -80 increase VGC level with 0x10 - */ - rt2800pci_set_vgc(rt2x00dev, qual, - rt2800pci_get_default_vgc(rt2x00dev) + - ((qual->rssi > -80) * 0x10)); -} - /* * Firmware functions */ @@ -1257,7 +244,7 @@ static int rt2800pci_load_firmware(struct rt2x00_dev *rt2x00dev, * Wait for stable hardware. */ for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00pci_register_read(rt2x00dev, MAC_CSR0, ®); + rt2800_register_read(rt2x00dev, MAC_CSR0, ®); if (reg && reg != ~0) break; msleep(1); @@ -1268,42 +255,42 @@ static int rt2800pci_load_firmware(struct rt2x00_dev *rt2x00dev, return -EBUSY; } - rt2x00pci_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000002); - rt2x00pci_register_write(rt2x00dev, AUTOWAKEUP_CFG, 0x00000000); + rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000002); + rt2800_register_write(rt2x00dev, AUTOWAKEUP_CFG, 0x00000000); /* * Disable DMA, will be reenabled later when enabling * the radio. */ - rt2x00pci_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_DMA_BUSY, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_DMA_BUSY, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1); - rt2x00pci_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); /* * enable Host program ram write selection */ reg = 0; rt2x00_set_field32(®, PBF_SYS_CTRL_HOST_RAM_WRITE, 1); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, reg); /* * Write firmware to device. */ - rt2x00pci_register_multiwrite(rt2x00dev, FIRMWARE_IMAGE_BASE, + rt2800_register_multiwrite(rt2x00dev, FIRMWARE_IMAGE_BASE, data, len); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00001); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00001); /* * Wait for device to stabilize. */ for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00pci_register_read(rt2x00dev, PBF_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, PBF_SYS_CTRL, ®); if (rt2x00_get_field32(reg, PBF_SYS_CTRL_READY)) break; msleep(1); @@ -1322,8 +309,8 @@ static int rt2800pci_load_firmware(struct rt2x00_dev *rt2x00dev, /* * Initialize BBP R/W access agent */ - rt2x00pci_register_write(rt2x00dev, H2M_BBP_AGENT, 0); - rt2x00pci_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); + rt2800_register_write(rt2x00dev, H2M_BBP_AGENT, 0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); return 0; } @@ -1373,7 +360,7 @@ static int rt2800pci_init_queues(struct rt2x00_dev *rt2x00dev) struct queue_entry_priv_pci *entry_priv; u32 reg; - rt2x00pci_register_read(rt2x00dev, WPDMA_RST_IDX, ®); + rt2800_register_read(rt2x00dev, WPDMA_RST_IDX, ®); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX0, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX1, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX2, 1); @@ -1381,539 +368,54 @@ static int rt2800pci_init_queues(struct rt2x00_dev *rt2x00dev) rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX4, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX5, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DRX_IDX0, 1); - rt2x00pci_register_write(rt2x00dev, WPDMA_RST_IDX, reg); + rt2800_register_write(rt2x00dev, WPDMA_RST_IDX, reg); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00); /* * Initialize registers. */ entry_priv = rt2x00dev->tx[0].entries[0].priv_data; - rt2x00pci_register_write(rt2x00dev, TX_BASE_PTR0, entry_priv->desc_dma); - rt2x00pci_register_write(rt2x00dev, TX_MAX_CNT0, rt2x00dev->tx[0].limit); - rt2x00pci_register_write(rt2x00dev, TX_CTX_IDX0, 0); - rt2x00pci_register_write(rt2x00dev, TX_DTX_IDX0, 0); + rt2800_register_write(rt2x00dev, TX_BASE_PTR0, entry_priv->desc_dma); + rt2800_register_write(rt2x00dev, TX_MAX_CNT0, rt2x00dev->tx[0].limit); + rt2800_register_write(rt2x00dev, TX_CTX_IDX0, 0); + rt2800_register_write(rt2x00dev, TX_DTX_IDX0, 0); entry_priv = rt2x00dev->tx[1].entries[0].priv_data; - rt2x00pci_register_write(rt2x00dev, TX_BASE_PTR1, entry_priv->desc_dma); - rt2x00pci_register_write(rt2x00dev, TX_MAX_CNT1, rt2x00dev->tx[1].limit); - rt2x00pci_register_write(rt2x00dev, TX_CTX_IDX1, 0); - rt2x00pci_register_write(rt2x00dev, TX_DTX_IDX1, 0); + rt2800_register_write(rt2x00dev, TX_BASE_PTR1, entry_priv->desc_dma); + rt2800_register_write(rt2x00dev, TX_MAX_CNT1, rt2x00dev->tx[1].limit); + rt2800_register_write(rt2x00dev, TX_CTX_IDX1, 0); + rt2800_register_write(rt2x00dev, TX_DTX_IDX1, 0); entry_priv = rt2x00dev->tx[2].entries[0].priv_data; - rt2x00pci_register_write(rt2x00dev, TX_BASE_PTR2, entry_priv->desc_dma); - rt2x00pci_register_write(rt2x00dev, TX_MAX_CNT2, rt2x00dev->tx[2].limit); - rt2x00pci_register_write(rt2x00dev, TX_CTX_IDX2, 0); - rt2x00pci_register_write(rt2x00dev, TX_DTX_IDX2, 0); + rt2800_register_write(rt2x00dev, TX_BASE_PTR2, entry_priv->desc_dma); + rt2800_register_write(rt2x00dev, TX_MAX_CNT2, rt2x00dev->tx[2].limit); + rt2800_register_write(rt2x00dev, TX_CTX_IDX2, 0); + rt2800_register_write(rt2x00dev, TX_DTX_IDX2, 0); entry_priv = rt2x00dev->tx[3].entries[0].priv_data; - rt2x00pci_register_write(rt2x00dev, TX_BASE_PTR3, entry_priv->desc_dma); - rt2x00pci_register_write(rt2x00dev, TX_MAX_CNT3, rt2x00dev->tx[3].limit); - rt2x00pci_register_write(rt2x00dev, TX_CTX_IDX3, 0); - rt2x00pci_register_write(rt2x00dev, TX_DTX_IDX3, 0); + rt2800_register_write(rt2x00dev, TX_BASE_PTR3, entry_priv->desc_dma); + rt2800_register_write(rt2x00dev, TX_MAX_CNT3, rt2x00dev->tx[3].limit); + rt2800_register_write(rt2x00dev, TX_CTX_IDX3, 0); + rt2800_register_write(rt2x00dev, TX_DTX_IDX3, 0); entry_priv = rt2x00dev->rx->entries[0].priv_data; - rt2x00pci_register_write(rt2x00dev, RX_BASE_PTR, entry_priv->desc_dma); - rt2x00pci_register_write(rt2x00dev, RX_MAX_CNT, rt2x00dev->rx[0].limit); - rt2x00pci_register_write(rt2x00dev, RX_CRX_IDX, rt2x00dev->rx[0].limit - 1); - rt2x00pci_register_write(rt2x00dev, RX_DRX_IDX, 0); + rt2800_register_write(rt2x00dev, RX_BASE_PTR, entry_priv->desc_dma); + rt2800_register_write(rt2x00dev, RX_MAX_CNT, rt2x00dev->rx[0].limit); + rt2800_register_write(rt2x00dev, RX_CRX_IDX, rt2x00dev->rx[0].limit - 1); + rt2800_register_write(rt2x00dev, RX_DRX_IDX, 0); /* * Enable global DMA configuration */ - rt2x00pci_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1); - rt2x00pci_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - - rt2x00pci_register_write(rt2x00dev, DELAY_INT_CFG, 0); - - return 0; -} - -static int rt2800pci_init_registers(struct rt2x00_dev *rt2x00dev) -{ - u32 reg; - unsigned int i; - - rt2x00pci_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003); - - rt2x00pci_register_read(rt2x00dev, MAC_SYS_CTRL, ®); - rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_CSR, 1); - rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_BBP, 1); - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, reg); - - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); - - rt2x00pci_register_read(rt2x00dev, BCN_OFFSET0, ®); - rt2x00_set_field32(®, BCN_OFFSET0_BCN0, 0xe0); /* 0x3800 */ - rt2x00_set_field32(®, BCN_OFFSET0_BCN1, 0xe8); /* 0x3a00 */ - rt2x00_set_field32(®, BCN_OFFSET0_BCN2, 0xf0); /* 0x3c00 */ - rt2x00_set_field32(®, BCN_OFFSET0_BCN3, 0xf8); /* 0x3e00 */ - rt2x00pci_register_write(rt2x00dev, BCN_OFFSET0, reg); - - rt2x00pci_register_read(rt2x00dev, BCN_OFFSET1, ®); - rt2x00_set_field32(®, BCN_OFFSET1_BCN4, 0xc8); /* 0x3200 */ - rt2x00_set_field32(®, BCN_OFFSET1_BCN5, 0xd0); /* 0x3400 */ - rt2x00_set_field32(®, BCN_OFFSET1_BCN6, 0x77); /* 0x1dc0 */ - rt2x00_set_field32(®, BCN_OFFSET1_BCN7, 0x6f); /* 0x1bc0 */ - rt2x00pci_register_write(rt2x00dev, BCN_OFFSET1, reg); - - rt2x00pci_register_write(rt2x00dev, LEGACY_BASIC_RATE, 0x0000013f); - rt2x00pci_register_write(rt2x00dev, HT_BASIC_RATE, 0x00008003); - - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); - - rt2x00pci_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_INTERVAL, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_SYNC, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TX_TIME_COMPENSATE, 0); - rt2x00pci_register_write(rt2x00dev, BCN_TIME_CFG, reg); - - rt2x00pci_register_write(rt2x00dev, TX_SW_CFG0, 0x00000000); - rt2x00pci_register_write(rt2x00dev, TX_SW_CFG1, 0x00080606); - - rt2x00pci_register_read(rt2x00dev, TX_LINK_CFG, ®); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFB_LIFETIME, 32); - rt2x00_set_field32(®, TX_LINK_CFG_MFB_ENABLE, 0); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_UMFS_ENABLE, 0); - rt2x00_set_field32(®, TX_LINK_CFG_TX_MRQ_EN, 0); - rt2x00_set_field32(®, TX_LINK_CFG_TX_RDG_EN, 0); - rt2x00_set_field32(®, TX_LINK_CFG_TX_CF_ACK_EN, 1); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFB, 0); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFS, 0); - rt2x00pci_register_write(rt2x00dev, TX_LINK_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, TX_TIMEOUT_CFG, ®); - rt2x00_set_field32(®, TX_TIMEOUT_CFG_MPDU_LIFETIME, 9); - rt2x00_set_field32(®, TX_TIMEOUT_CFG_TX_OP_TIMEOUT, 10); - rt2x00pci_register_write(rt2x00dev, TX_TIMEOUT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, MAX_LEN_CFG, ®); - rt2x00_set_field32(®, MAX_LEN_CFG_MAX_MPDU, AGGREGATION_SIZE); - if (rt2x00_rev(&rt2x00dev->chip) >= RT2880E_VERSION && - rt2x00_rev(&rt2x00dev->chip) < RT3070_VERSION) - rt2x00_set_field32(®, MAX_LEN_CFG_MAX_PSDU, 2); - else - rt2x00_set_field32(®, MAX_LEN_CFG_MAX_PSDU, 1); - rt2x00_set_field32(®, MAX_LEN_CFG_MIN_PSDU, 0); - rt2x00_set_field32(®, MAX_LEN_CFG_MIN_MPDU, 0); - rt2x00pci_register_write(rt2x00dev, MAX_LEN_CFG, reg); - - rt2x00pci_register_write(rt2x00dev, PBF_MAX_PCNT, 0x1f3fbf9f); - - rt2x00pci_register_read(rt2x00dev, AUTO_RSP_CFG, ®); - rt2x00_set_field32(®, AUTO_RSP_CFG_AUTORESPONDER, 1); - rt2x00_set_field32(®, AUTO_RSP_CFG_CTS_40_MMODE, 0); - rt2x00_set_field32(®, AUTO_RSP_CFG_CTS_40_MREF, 0); - rt2x00_set_field32(®, AUTO_RSP_CFG_DUAL_CTS_EN, 0); - rt2x00_set_field32(®, AUTO_RSP_CFG_ACK_CTS_PSM_BIT, 0); - rt2x00pci_register_write(rt2x00dev, AUTO_RSP_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, CCK_PROT_CFG, ®); - rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_RATE, 8); - rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00pci_register_write(rt2x00dev, CCK_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, OFDM_PROT_CFG, ®); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_RATE, 8); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00pci_register_write(rt2x00dev, OFDM_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, MM20_PROT_CFG, ®); - rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_RATE, 0x4004); - rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM40, 0); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_GF40, 0); - rt2x00pci_register_write(rt2x00dev, MM20_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, MM40_PROT_CFG, ®); - rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_RATE, 0x4084); - rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00pci_register_write(rt2x00dev, MM40_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, GF20_PROT_CFG, ®); - rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_RATE, 0x4004); - rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM40, 0); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_GF40, 0); - rt2x00pci_register_write(rt2x00dev, GF20_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, GF40_PROT_CFG, ®); - rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_RATE, 0x4084); - rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00pci_register_write(rt2x00dev, GF40_PROT_CFG, reg); - - rt2x00pci_register_write(rt2x00dev, TXOP_CTRL_CFG, 0x0000583f); - rt2x00pci_register_write(rt2x00dev, TXOP_HLDR_ET, 0x00000002); - - rt2x00pci_register_read(rt2x00dev, TX_RTS_CFG, ®); - rt2x00_set_field32(®, TX_RTS_CFG_AUTO_RTS_RETRY_LIMIT, 32); - rt2x00_set_field32(®, TX_RTS_CFG_RTS_THRES, - IEEE80211_MAX_RTS_THRESHOLD); - rt2x00_set_field32(®, TX_RTS_CFG_RTS_FBK_EN, 0); - rt2x00pci_register_write(rt2x00dev, TX_RTS_CFG, reg); - - rt2x00pci_register_write(rt2x00dev, EXP_ACK_TIME, 0x002400ca); - rt2x00pci_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003); - - /* - * ASIC will keep garbage value after boot, clear encryption keys. - */ - for (i = 0; i < 4; i++) - rt2x00pci_register_write(rt2x00dev, - SHARED_KEY_MODE_ENTRY(i), 0); - - for (i = 0; i < 256; i++) { - u32 wcid[2] = { 0xffffffff, 0x00ffffff }; - rt2x00pci_register_multiwrite(rt2x00dev, MAC_WCID_ENTRY(i), - wcid, sizeof(wcid)); - - rt2x00pci_register_write(rt2x00dev, MAC_WCID_ATTR_ENTRY(i), 1); - rt2x00pci_register_write(rt2x00dev, MAC_IVEIV_ENTRY(i), 0); - } - - /* - * Clear all beacons - * For the Beacon base registers we only need to clear - * the first byte since that byte contains the VALID and OWNER - * bits which (when set to 0) will invalidate the entire beacon. - */ - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE0, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE1, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE2, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE3, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE4, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE5, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE6, 0); - rt2x00pci_register_write(rt2x00dev, HW_BEACON_BASE7, 0); - - rt2x00pci_register_read(rt2x00dev, HT_FBK_CFG0, ®); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS0FBK, 0); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS1FBK, 0); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS2FBK, 1); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS3FBK, 2); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS4FBK, 3); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS5FBK, 4); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS6FBK, 5); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS7FBK, 6); - rt2x00pci_register_write(rt2x00dev, HT_FBK_CFG0, reg); - - rt2x00pci_register_read(rt2x00dev, HT_FBK_CFG1, ®); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS8FBK, 8); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS9FBK, 8); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS10FBK, 9); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS11FBK, 10); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS12FBK, 11); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS13FBK, 12); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS14FBK, 13); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS15FBK, 14); - rt2x00pci_register_write(rt2x00dev, HT_FBK_CFG1, reg); - - rt2x00pci_register_read(rt2x00dev, LG_FBK_CFG0, ®); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS0FBK, 8); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS1FBK, 8); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS2FBK, 9); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS3FBK, 10); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS4FBK, 11); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS5FBK, 12); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS6FBK, 13); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS7FBK, 14); - rt2x00pci_register_write(rt2x00dev, LG_FBK_CFG0, reg); - - rt2x00pci_register_read(rt2x00dev, LG_FBK_CFG1, ®); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS0FBK, 0); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS1FBK, 0); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS2FBK, 1); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS3FBK, 2); - rt2x00pci_register_write(rt2x00dev, LG_FBK_CFG1, reg); - - /* - * We must clear the error counters. - * These registers are cleared on read, - * so we may pass a useless variable to store the value. - */ - rt2x00pci_register_read(rt2x00dev, RX_STA_CNT0, ®); - rt2x00pci_register_read(rt2x00dev, RX_STA_CNT1, ®); - rt2x00pci_register_read(rt2x00dev, RX_STA_CNT2, ®); - rt2x00pci_register_read(rt2x00dev, TX_STA_CNT0, ®); - rt2x00pci_register_read(rt2x00dev, TX_STA_CNT1, ®); - rt2x00pci_register_read(rt2x00dev, TX_STA_CNT2, ®); - - return 0; -} - -static int rt2800pci_wait_bbp_rf_ready(struct rt2x00_dev *rt2x00dev) -{ - unsigned int i; - u32 reg; - - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00pci_register_read(rt2x00dev, MAC_STATUS_CFG, ®); - if (!rt2x00_get_field32(reg, MAC_STATUS_CFG_BBP_RF_BUSY)) - return 0; - - udelay(REGISTER_BUSY_DELAY); - } - - ERROR(rt2x00dev, "BBP/RF register access failed, aborting.\n"); - return -EACCES; -} - -static int rt2800pci_wait_bbp_ready(struct rt2x00_dev *rt2x00dev) -{ - unsigned int i; - u8 value; - - /* - * BBP was enabled after firmware was loaded, - * but we need to reactivate it now. - */ - rt2x00pci_register_write(rt2x00dev, H2M_BBP_AGENT, 0); - rt2x00pci_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); - msleep(1); - - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2800pci_bbp_read(rt2x00dev, 0, &value); - if ((value != 0xff) && (value != 0x00)) - return 0; - udelay(REGISTER_BUSY_DELAY); - } - - ERROR(rt2x00dev, "BBP register access failed, aborting.\n"); - return -EACCES; -} - -static int rt2800pci_init_bbp(struct rt2x00_dev *rt2x00dev) -{ - unsigned int i; - u16 eeprom; - u8 reg_id; - u8 value; - - if (unlikely(rt2800pci_wait_bbp_rf_ready(rt2x00dev) || - rt2800pci_wait_bbp_ready(rt2x00dev))) - return -EACCES; - - rt2800pci_bbp_write(rt2x00dev, 65, 0x2c); - rt2800pci_bbp_write(rt2x00dev, 66, 0x38); - rt2800pci_bbp_write(rt2x00dev, 69, 0x12); - rt2800pci_bbp_write(rt2x00dev, 70, 0x0a); - rt2800pci_bbp_write(rt2x00dev, 73, 0x10); - rt2800pci_bbp_write(rt2x00dev, 81, 0x37); - rt2800pci_bbp_write(rt2x00dev, 82, 0x62); - rt2800pci_bbp_write(rt2x00dev, 83, 0x6a); - rt2800pci_bbp_write(rt2x00dev, 84, 0x99); - rt2800pci_bbp_write(rt2x00dev, 86, 0x00); - rt2800pci_bbp_write(rt2x00dev, 91, 0x04); - rt2800pci_bbp_write(rt2x00dev, 92, 0x00); - rt2800pci_bbp_write(rt2x00dev, 103, 0x00); - rt2800pci_bbp_write(rt2x00dev, 105, 0x05); - - if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) { - rt2800pci_bbp_write(rt2x00dev, 69, 0x16); - rt2800pci_bbp_write(rt2x00dev, 73, 0x12); - } - - if (rt2x00_rev(&rt2x00dev->chip) > RT2860D_VERSION) - rt2800pci_bbp_write(rt2x00dev, 84, 0x19); - - if (rt2x00_rt(&rt2x00dev->chip, RT3052)) { - rt2800pci_bbp_write(rt2x00dev, 31, 0x08); - rt2800pci_bbp_write(rt2x00dev, 78, 0x0e); - rt2800pci_bbp_write(rt2x00dev, 80, 0x08); - } - - for (i = 0; i < EEPROM_BBP_SIZE; i++) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i, &eeprom); - - if (eeprom != 0xffff && eeprom != 0x0000) { - reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID); - value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE); - rt2800pci_bbp_write(rt2x00dev, reg_id, value); - } - } + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - return 0; -} - -static u8 rt2800pci_init_rx_filter(struct rt2x00_dev *rt2x00dev, - bool bw40, u8 rfcsr24, u8 filter_target) -{ - unsigned int i; - u8 bbp; - u8 rfcsr; - u8 passband; - u8 stopband; - u8 overtuned = 0; - - rt2800pci_rfcsr_write(rt2x00dev, 24, rfcsr24); - - rt2800pci_bbp_read(rt2x00dev, 4, &bbp); - rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * bw40); - rt2800pci_bbp_write(rt2x00dev, 4, bbp); - - rt2800pci_rfcsr_read(rt2x00dev, 22, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 1); - rt2800pci_rfcsr_write(rt2x00dev, 22, rfcsr); - - /* - * Set power & frequency of passband test tone - */ - rt2800pci_bbp_write(rt2x00dev, 24, 0); - - for (i = 0; i < 100; i++) { - rt2800pci_bbp_write(rt2x00dev, 25, 0x90); - msleep(1); - - rt2800pci_bbp_read(rt2x00dev, 55, &passband); - if (passband) - break; - } - - /* - * Set power & frequency of stopband test tone - */ - rt2800pci_bbp_write(rt2x00dev, 24, 0x06); - - for (i = 0; i < 100; i++) { - rt2800pci_bbp_write(rt2x00dev, 25, 0x90); - msleep(1); - - rt2800pci_bbp_read(rt2x00dev, 55, &stopband); - - if ((passband - stopband) <= filter_target) { - rfcsr24++; - overtuned += ((passband - stopband) == filter_target); - } else - break; - - rt2800pci_rfcsr_write(rt2x00dev, 24, rfcsr24); - } - - rfcsr24 -= !!overtuned; - - rt2800pci_rfcsr_write(rt2x00dev, 24, rfcsr24); - return rfcsr24; -} - -static int rt2800pci_init_rfcsr(struct rt2x00_dev *rt2x00dev) -{ - u8 rfcsr; - u8 bbp; - - if (!rt2x00_rf(&rt2x00dev->chip, RF3020) && - !rt2x00_rf(&rt2x00dev->chip, RF3021) && - !rt2x00_rf(&rt2x00dev->chip, RF3022)) - return 0; - - /* - * Init RF calibration. - */ - rt2800pci_rfcsr_read(rt2x00dev, 30, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 1); - rt2800pci_rfcsr_write(rt2x00dev, 30, rfcsr); - msleep(1); - rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 0); - rt2800pci_rfcsr_write(rt2x00dev, 30, rfcsr); - - rt2800pci_rfcsr_write(rt2x00dev, 0, 0x50); - rt2800pci_rfcsr_write(rt2x00dev, 1, 0x01); - rt2800pci_rfcsr_write(rt2x00dev, 2, 0xf7); - rt2800pci_rfcsr_write(rt2x00dev, 3, 0x75); - rt2800pci_rfcsr_write(rt2x00dev, 4, 0x40); - rt2800pci_rfcsr_write(rt2x00dev, 5, 0x03); - rt2800pci_rfcsr_write(rt2x00dev, 6, 0x02); - rt2800pci_rfcsr_write(rt2x00dev, 7, 0x50); - rt2800pci_rfcsr_write(rt2x00dev, 8, 0x39); - rt2800pci_rfcsr_write(rt2x00dev, 9, 0x0f); - rt2800pci_rfcsr_write(rt2x00dev, 10, 0x60); - rt2800pci_rfcsr_write(rt2x00dev, 11, 0x21); - rt2800pci_rfcsr_write(rt2x00dev, 12, 0x75); - rt2800pci_rfcsr_write(rt2x00dev, 13, 0x75); - rt2800pci_rfcsr_write(rt2x00dev, 14, 0x90); - rt2800pci_rfcsr_write(rt2x00dev, 15, 0x58); - rt2800pci_rfcsr_write(rt2x00dev, 16, 0xb3); - rt2800pci_rfcsr_write(rt2x00dev, 17, 0x92); - rt2800pci_rfcsr_write(rt2x00dev, 18, 0x2c); - rt2800pci_rfcsr_write(rt2x00dev, 19, 0x02); - rt2800pci_rfcsr_write(rt2x00dev, 20, 0xba); - rt2800pci_rfcsr_write(rt2x00dev, 21, 0xdb); - rt2800pci_rfcsr_write(rt2x00dev, 22, 0x00); - rt2800pci_rfcsr_write(rt2x00dev, 23, 0x31); - rt2800pci_rfcsr_write(rt2x00dev, 24, 0x08); - rt2800pci_rfcsr_write(rt2x00dev, 25, 0x01); - rt2800pci_rfcsr_write(rt2x00dev, 26, 0x25); - rt2800pci_rfcsr_write(rt2x00dev, 27, 0x23); - rt2800pci_rfcsr_write(rt2x00dev, 28, 0x13); - rt2800pci_rfcsr_write(rt2x00dev, 29, 0x83); - - /* - * Set RX Filter calibration for 20MHz and 40MHz - */ - rt2x00dev->calibration[0] = - rt2800pci_init_rx_filter(rt2x00dev, false, 0x07, 0x16); - rt2x00dev->calibration[1] = - rt2800pci_init_rx_filter(rt2x00dev, true, 0x27, 0x19); - - /* - * Set back to initial state - */ - rt2800pci_bbp_write(rt2x00dev, 24, 0); - - rt2800pci_rfcsr_read(rt2x00dev, 22, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 0); - rt2800pci_rfcsr_write(rt2x00dev, 22, rfcsr); - - /* - * set BBP back to BW20 - */ - rt2800pci_bbp_read(rt2x00dev, 4, &bbp); - rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 0); - rt2800pci_bbp_write(rt2x00dev, 4, bbp); + rt2800_register_write(rt2x00dev, DELAY_INT_CFG, 0); return 0; } @@ -1926,11 +428,11 @@ static void rt2800pci_toggle_rx(struct rt2x00_dev *rt2x00dev, { u32 reg; - rt2x00pci_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_RX, (state == STATE_RADIO_RX_ON) || (state == STATE_RADIO_RX_ON_LINK)); - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); } static void rt2800pci_toggle_irq(struct rt2x00_dev *rt2x00dev, @@ -1944,11 +446,11 @@ static void rt2800pci_toggle_irq(struct rt2x00_dev *rt2x00dev, * should clear the register to assure a clean state. */ if (state == STATE_RADIO_IRQ_ON) { - rt2x00pci_register_read(rt2x00dev, INT_SOURCE_CSR, ®); - rt2x00pci_register_write(rt2x00dev, INT_SOURCE_CSR, reg); + rt2800_register_read(rt2x00dev, INT_SOURCE_CSR, ®); + rt2800_register_write(rt2x00dev, INT_SOURCE_CSR, reg); } - rt2x00pci_register_read(rt2x00dev, INT_MASK_CSR, ®); + rt2800_register_read(rt2x00dev, INT_MASK_CSR, ®); rt2x00_set_field32(®, INT_MASK_CSR_RXDELAYINT, mask); rt2x00_set_field32(®, INT_MASK_CSR_TXDELAYINT, mask); rt2x00_set_field32(®, INT_MASK_CSR_RX_DONE, mask); @@ -1967,7 +469,7 @@ static void rt2800pci_toggle_irq(struct rt2x00_dev *rt2x00dev, rt2x00_set_field32(®, INT_MASK_CSR_GPTIMER, mask); rt2x00_set_field32(®, INT_MASK_CSR_RX_COHERENT, mask); rt2x00_set_field32(®, INT_MASK_CSR_TX_COHERENT, mask); - rt2x00pci_register_write(rt2x00dev, INT_MASK_CSR, reg); + rt2800_register_write(rt2x00dev, INT_MASK_CSR, reg); } static int rt2800pci_wait_wpdma_ready(struct rt2x00_dev *rt2x00dev) @@ -1976,7 +478,7 @@ static int rt2800pci_wait_wpdma_ready(struct rt2x00_dev *rt2x00dev) u32 reg; for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00pci_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); if (!rt2x00_get_field32(reg, WPDMA_GLO_CFG_TX_DMA_BUSY) && !rt2x00_get_field32(reg, WPDMA_GLO_CFG_RX_DMA_BUSY)) return 0; @@ -1998,50 +500,50 @@ static int rt2800pci_enable_radio(struct rt2x00_dev *rt2x00dev) */ if (unlikely(rt2800pci_wait_wpdma_ready(rt2x00dev) || rt2800pci_init_queues(rt2x00dev) || - rt2800pci_init_registers(rt2x00dev) || + rt2800_init_registers(rt2x00dev) || rt2800pci_wait_wpdma_ready(rt2x00dev) || - rt2800pci_init_bbp(rt2x00dev) || - rt2800pci_init_rfcsr(rt2x00dev))) + rt2800_init_bbp(rt2x00dev) || + rt2800_init_rfcsr(rt2x00dev))) return -EIO; /* * Send signal to firmware during boot time. */ - rt2800pci_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0); + rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0); /* * Enable RX. */ - rt2x00pci_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_TX, 1); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_RX, 0); - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); - rt2x00pci_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 1); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 1); rt2x00_set_field32(®, WPDMA_GLO_CFG_WP_DMA_BURST_SIZE, 2); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1); - rt2x00pci_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - rt2x00pci_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_TX, 1); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_RX, 1); - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); /* * Initialize LED control */ rt2x00_eeprom_read(rt2x00dev, EEPROM_LED1, &word); - rt2800pci_mcu_request(rt2x00dev, MCU_LED_1, 0xff, + rt2800_mcu_request(rt2x00dev, MCU_LED_1, 0xff, word & 0xff, (word >> 8) & 0xff); rt2x00_eeprom_read(rt2x00dev, EEPROM_LED2, &word); - rt2800pci_mcu_request(rt2x00dev, MCU_LED_2, 0xff, + rt2800_mcu_request(rt2x00dev, MCU_LED_2, 0xff, word & 0xff, (word >> 8) & 0xff); rt2x00_eeprom_read(rt2x00dev, EEPROM_LED3, &word); - rt2800pci_mcu_request(rt2x00dev, MCU_LED_3, 0xff, + rt2800_mcu_request(rt2x00dev, MCU_LED_3, 0xff, word & 0xff, (word >> 8) & 0xff); return 0; @@ -2051,21 +553,21 @@ static void rt2800pci_disable_radio(struct rt2x00_dev *rt2x00dev) { u32 reg; - rt2x00pci_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_DMA_BUSY, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_DMA_BUSY, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1); - rt2x00pci_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - rt2x00pci_register_write(rt2x00dev, MAC_SYS_CTRL, 0); - rt2x00pci_register_write(rt2x00dev, PWR_PIN_CFG, 0); - rt2x00pci_register_write(rt2x00dev, TX_PIN_CFG, 0); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, 0); + rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0); + rt2800_register_write(rt2x00dev, TX_PIN_CFG, 0); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00001280); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00001280); - rt2x00pci_register_read(rt2x00dev, WPDMA_RST_IDX, ®); + rt2800_register_read(rt2x00dev, WPDMA_RST_IDX, ®); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX0, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX1, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX2, 1); @@ -2073,10 +575,10 @@ static void rt2800pci_disable_radio(struct rt2x00_dev *rt2x00dev) rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX4, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX5, 1); rt2x00_set_field32(®, WPDMA_RST_IDX_DRX_IDX0, 1); - rt2x00pci_register_write(rt2x00dev, WPDMA_RST_IDX, reg); + rt2800_register_write(rt2x00dev, WPDMA_RST_IDX, reg); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f); - rt2x00pci_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00); /* Wait for DMA, ignore error */ rt2800pci_wait_wpdma_ready(rt2x00dev); @@ -2090,10 +592,10 @@ static int rt2800pci_set_state(struct rt2x00_dev *rt2x00dev, * if the device is booting and wasn't asleep it will return * failure when attempting to wakeup. */ - rt2800pci_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0, 2); + rt2800_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0, 2); if (state == STATE_AWAKE) { - rt2800pci_mcu_request(rt2x00dev, MCU_WAKEUP, TOKEN_WAKUP, 0, 0); + rt2800_mcu_request(rt2x00dev, MCU_WAKEUP, TOKEN_WAKUP, 0, 0); rt2800pci_mcu_status(rt2x00dev, TOKEN_WAKUP); } @@ -2195,7 +697,7 @@ static void rt2800pci_write_tx_desc(struct rt2x00_dev *rt2x00dev, rt2x00_set_field32(&word, TXWI_W1_BW_WIN_SIZE, txdesc->ba_size); rt2x00_set_field32(&word, TXWI_W1_WIRELESS_CLI_ID, test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags) ? - (skbdesc->entry->entry_idx + 1) : 0xff); + txdesc->key_idx : 0xff); rt2x00_set_field32(&word, TXWI_W1_MPDU_TOTAL_BYTE_COUNT, skb->len - txdesc->l2pad); rt2x00_set_field32(&word, TXWI_W1_PACKETID, @@ -2204,8 +706,8 @@ static void rt2800pci_write_tx_desc(struct rt2x00_dev *rt2x00dev, /* * Always write 0 to IV/EIV fields, hardware will insert the IV - * from the IVEIV register when ENTRY_TXD_ENCRYPT_IV is set to 0. - * When ENTRY_TXD_ENCRYPT_IV is set to 1 it will use the IV data + * from the IVEIV register when TXD_W3_WIV is set to 0. + * When TXD_W3_WIV is set to 1 it will use the IV data * from the descriptor. The TXWI_W1_WIRELESS_CLI_ID indicates which * crypto entry in the registers should be used to encrypt the frame. */ @@ -2265,18 +767,18 @@ static void rt2800pci_write_beacon(struct queue_entry *entry) * Disable beaconing while we are reloading the beacon data, * otherwise we might be sending out invalid data. */ - rt2x00pci_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0); - rt2x00pci_register_write(rt2x00dev, BCN_TIME_CFG, reg); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); /* * Write entire beacon with descriptor to register. */ beacon_base = HW_BEACON_OFFSET(entry->entry_idx); - rt2x00pci_register_multiwrite(rt2x00dev, + rt2800_register_multiwrite(rt2x00dev, beacon_base, skbdesc->desc, skbdesc->desc_len); - rt2x00pci_register_multiwrite(rt2x00dev, + rt2800_register_multiwrite(rt2x00dev, beacon_base + skbdesc->desc_len, entry->skb->data, entry->skb->len); @@ -2295,12 +797,12 @@ static void rt2800pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev, u32 reg; if (queue_idx == QID_BEACON) { - rt2x00pci_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); if (!rt2x00_get_field32(reg, BCN_TIME_CFG_BEACON_GEN)) { rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1); rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1); rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 1); - rt2x00pci_register_write(rt2x00dev, BCN_TIME_CFG, reg); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); } return; } @@ -2316,7 +818,7 @@ static void rt2800pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev, else qidx = queue_idx; - rt2x00pci_register_write(rt2x00dev, TX_CTX_IDX(qidx), idx); + rt2800_register_write(rt2x00dev, TX_CTX_IDX(qidx), idx); } static void rt2800pci_kill_tx_queue(struct rt2x00_dev *rt2x00dev, @@ -2325,16 +827,16 @@ static void rt2800pci_kill_tx_queue(struct rt2x00_dev *rt2x00dev, u32 reg; if (qid == QID_BEACON) { - rt2x00pci_register_write(rt2x00dev, BCN_TIME_CFG, 0); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, 0); return; } - rt2x00pci_register_read(rt2x00dev, WPDMA_RST_IDX, ®); + rt2800_register_read(rt2x00dev, WPDMA_RST_IDX, ®); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX0, (qid == QID_AC_BE)); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX1, (qid == QID_AC_BK)); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX2, (qid == QID_AC_VI)); rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX3, (qid == QID_AC_VO)); - rt2x00pci_register_write(rt2x00dev, WPDMA_RST_IDX, reg); + rt2800_register_write(rt2x00dev, WPDMA_RST_IDX, reg); } /* @@ -2430,7 +932,7 @@ static void rt2800pci_fill_rxdone(struct queue_entry *entry, * Set RX IDX in register to inform hardware that we have handled * this entry and it is available for reuse again. */ - rt2x00pci_register_write(rt2x00dev, RX_CRX_IDX, entry->entry_idx); + rt2800_register_write(rt2x00dev, RX_CRX_IDX, entry->entry_idx); /* * Remove TXWI descriptor from start of buffer. @@ -2467,7 +969,7 @@ static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev) old_reg = 0; while (1) { - rt2x00pci_register_read(rt2x00dev, TX_STA_FIFO, ®); + rt2800_register_read(rt2x00dev, TX_STA_FIFO, ®); if (!rt2x00_get_field32(reg, TX_STA_FIFO_VALID)) break; @@ -2551,8 +1053,8 @@ static irqreturn_t rt2800pci_interrupt(int irq, void *dev_instance) u32 reg; /* Read status and ACK all interrupts */ - rt2x00pci_register_read(rt2x00dev, INT_SOURCE_CSR, ®); - rt2x00pci_register_write(rt2x00dev, INT_SOURCE_CSR, reg); + rt2800_register_read(rt2x00dev, INT_SOURCE_CSR, ®); + rt2800_register_write(rt2x00dev, INT_SOURCE_CSR, reg); if (!reg) return IRQ_NONE; @@ -2709,7 +1211,7 @@ static int rt2800pci_init_eeprom(struct rt2x00_dev *rt2x00dev) * Identify RF chipset. */ value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE); - rt2x00pci_register_read(rt2x00dev, MAC_CSR0, ®); + rt2800_register_read(rt2x00dev, MAC_CSR0, ®); rt2x00_set_chip_rf(rt2x00dev, value, reg); if (!rt2x00_rf(&rt2x00dev->chip, RF2820) && @@ -2758,9 +1260,9 @@ static int rt2800pci_init_eeprom(struct rt2x00_dev *rt2x00dev) * Store led settings, for correct led behaviour. */ #ifdef CONFIG_RT2X00_LIB_LEDS - rt2800pci_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); - rt2800pci_init_led(rt2x00dev, &rt2x00dev->led_assoc, LED_TYPE_ASSOC); - rt2800pci_init_led(rt2x00dev, &rt2x00dev->led_qual, LED_TYPE_QUALITY); + rt2800_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); + rt2800_init_led(rt2x00dev, &rt2x00dev->led_assoc, LED_TYPE_ASSOC); + rt2800_init_led(rt2x00dev, &rt2x00dev->led_qual, LED_TYPE_QUALITY); rt2x00_eeprom_read(rt2x00dev, EEPROM_FREQ, &rt2x00dev->led_mcu_reg); #endif /* CONFIG_RT2X00_LIB_LEDS */ @@ -2948,10 +1450,25 @@ static int rt2800pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev) return 0; } +static const struct rt2800_ops rt2800pci_rt2800_ops = { + .register_read = rt2x00pci_register_read, + .register_write = rt2x00pci_register_write, + .register_write_lock = rt2x00pci_register_write, /* same for PCI */ + + .register_multiread = rt2x00pci_register_multiread, + .register_multiwrite = rt2x00pci_register_multiwrite, + + .regbusy_read = rt2x00pci_regbusy_read, +}; + static int rt2800pci_probe_hw(struct rt2x00_dev *rt2x00dev) { int retval; + rt2x00_set_chip_intf(rt2x00dev, RT2X00_CHIP_INTF_PCI); + + rt2x00dev->priv = (void *)&rt2800pci_rt2800_ops; + /* * Allocate eeprom data. */ @@ -2996,161 +1513,6 @@ static int rt2800pci_probe_hw(struct rt2x00_dev *rt2x00dev) return 0; } -/* - * IEEE80211 stack callback functions. - */ -static void rt2800pci_get_tkip_seq(struct ieee80211_hw *hw, u8 hw_key_idx, - u32 *iv32, u16 *iv16) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - struct mac_iveiv_entry iveiv_entry; - u32 offset; - - offset = MAC_IVEIV_ENTRY(hw_key_idx); - rt2x00pci_register_multiread(rt2x00dev, offset, - &iveiv_entry, sizeof(iveiv_entry)); - - memcpy(&iveiv_entry.iv[0], iv16, sizeof(iv16)); - memcpy(&iveiv_entry.iv[4], iv32, sizeof(iv32)); -} - -static int rt2800pci_set_rts_threshold(struct ieee80211_hw *hw, u32 value) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - u32 reg; - bool enabled = (value < IEEE80211_MAX_RTS_THRESHOLD); - - rt2x00pci_register_read(rt2x00dev, TX_RTS_CFG, ®); - rt2x00_set_field32(®, TX_RTS_CFG_RTS_THRES, value); - rt2x00pci_register_write(rt2x00dev, TX_RTS_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, CCK_PROT_CFG, ®); - rt2x00_set_field32(®, CCK_PROT_CFG_RTS_TH_EN, enabled); - rt2x00pci_register_write(rt2x00dev, CCK_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, OFDM_PROT_CFG, ®); - rt2x00_set_field32(®, OFDM_PROT_CFG_RTS_TH_EN, enabled); - rt2x00pci_register_write(rt2x00dev, OFDM_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, MM20_PROT_CFG, ®); - rt2x00_set_field32(®, MM20_PROT_CFG_RTS_TH_EN, enabled); - rt2x00pci_register_write(rt2x00dev, MM20_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, MM40_PROT_CFG, ®); - rt2x00_set_field32(®, MM40_PROT_CFG_RTS_TH_EN, enabled); - rt2x00pci_register_write(rt2x00dev, MM40_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, GF20_PROT_CFG, ®); - rt2x00_set_field32(®, GF20_PROT_CFG_RTS_TH_EN, enabled); - rt2x00pci_register_write(rt2x00dev, GF20_PROT_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, GF40_PROT_CFG, ®); - rt2x00_set_field32(®, GF40_PROT_CFG_RTS_TH_EN, enabled); - rt2x00pci_register_write(rt2x00dev, GF40_PROT_CFG, reg); - - return 0; -} - -static int rt2800pci_conf_tx(struct ieee80211_hw *hw, u16 queue_idx, - const struct ieee80211_tx_queue_params *params) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - struct data_queue *queue; - struct rt2x00_field32 field; - int retval; - u32 reg; - u32 offset; - - /* - * First pass the configuration through rt2x00lib, that will - * update the queue settings and validate the input. After that - * we are free to update the registers based on the value - * in the queue parameter. - */ - retval = rt2x00mac_conf_tx(hw, queue_idx, params); - if (retval) - return retval; - - /* - * We only need to perform additional register initialization - * for WMM queues/ - */ - if (queue_idx >= 4) - return 0; - - queue = rt2x00queue_get_queue(rt2x00dev, queue_idx); - - /* Update WMM TXOP register */ - offset = WMM_TXOP0_CFG + (sizeof(u32) * (!!(queue_idx & 2))); - field.bit_offset = (queue_idx & 1) * 16; - field.bit_mask = 0xffff << field.bit_offset; - - rt2x00pci_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, field, queue->txop); - rt2x00pci_register_write(rt2x00dev, offset, reg); - - /* Update WMM registers */ - field.bit_offset = queue_idx * 4; - field.bit_mask = 0xf << field.bit_offset; - - rt2x00pci_register_read(rt2x00dev, WMM_AIFSN_CFG, ®); - rt2x00_set_field32(®, field, queue->aifs); - rt2x00pci_register_write(rt2x00dev, WMM_AIFSN_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, WMM_CWMIN_CFG, ®); - rt2x00_set_field32(®, field, queue->cw_min); - rt2x00pci_register_write(rt2x00dev, WMM_CWMIN_CFG, reg); - - rt2x00pci_register_read(rt2x00dev, WMM_CWMAX_CFG, ®); - rt2x00_set_field32(®, field, queue->cw_max); - rt2x00pci_register_write(rt2x00dev, WMM_CWMAX_CFG, reg); - - /* Update EDCA registers */ - offset = EDCA_AC0_CFG + (sizeof(u32) * queue_idx); - - rt2x00pci_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, EDCA_AC0_CFG_TX_OP, queue->txop); - rt2x00_set_field32(®, EDCA_AC0_CFG_AIFSN, queue->aifs); - rt2x00_set_field32(®, EDCA_AC0_CFG_CWMIN, queue->cw_min); - rt2x00_set_field32(®, EDCA_AC0_CFG_CWMAX, queue->cw_max); - rt2x00pci_register_write(rt2x00dev, offset, reg); - - return 0; -} - -static u64 rt2800pci_get_tsf(struct ieee80211_hw *hw) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - u64 tsf; - u32 reg; - - rt2x00pci_register_read(rt2x00dev, TSF_TIMER_DW1, ®); - tsf = (u64) rt2x00_get_field32(reg, TSF_TIMER_DW1_HIGH_WORD) << 32; - rt2x00pci_register_read(rt2x00dev, TSF_TIMER_DW0, ®); - tsf |= rt2x00_get_field32(reg, TSF_TIMER_DW0_LOW_WORD); - - return tsf; -} - -static const struct ieee80211_ops rt2800pci_mac80211_ops = { - .tx = rt2x00mac_tx, - .start = rt2x00mac_start, - .stop = rt2x00mac_stop, - .add_interface = rt2x00mac_add_interface, - .remove_interface = rt2x00mac_remove_interface, - .config = rt2x00mac_config, - .configure_filter = rt2x00mac_configure_filter, - .set_key = rt2x00mac_set_key, - .get_stats = rt2x00mac_get_stats, - .get_tkip_seq = rt2800pci_get_tkip_seq, - .set_rts_threshold = rt2800pci_set_rts_threshold, - .bss_info_changed = rt2x00mac_bss_info_changed, - .conf_tx = rt2800pci_conf_tx, - .get_tx_stats = rt2x00mac_get_tx_stats, - .get_tsf = rt2800pci_get_tsf, - .rfkill_poll = rt2x00mac_rfkill_poll, -}; - static const struct rt2x00lib_ops rt2800pci_rt2x00_ops = { .irq_handler = rt2800pci_interrupt, .probe_hw = rt2800pci_probe_hw, @@ -3162,23 +1524,23 @@ static const struct rt2x00lib_ops rt2800pci_rt2x00_ops = { .get_entry_state = rt2800pci_get_entry_state, .clear_entry = rt2800pci_clear_entry, .set_device_state = rt2800pci_set_device_state, - .rfkill_poll = rt2800pci_rfkill_poll, - .link_stats = rt2800pci_link_stats, - .reset_tuner = rt2800pci_reset_tuner, - .link_tuner = rt2800pci_link_tuner, + .rfkill_poll = rt2800_rfkill_poll, + .link_stats = rt2800_link_stats, + .reset_tuner = rt2800_reset_tuner, + .link_tuner = rt2800_link_tuner, .write_tx_desc = rt2800pci_write_tx_desc, .write_tx_data = rt2x00pci_write_tx_data, .write_beacon = rt2800pci_write_beacon, .kick_tx_queue = rt2800pci_kick_tx_queue, .kill_tx_queue = rt2800pci_kill_tx_queue, .fill_rxdone = rt2800pci_fill_rxdone, - .config_shared_key = rt2800pci_config_shared_key, - .config_pairwise_key = rt2800pci_config_pairwise_key, - .config_filter = rt2800pci_config_filter, - .config_intf = rt2800pci_config_intf, - .config_erp = rt2800pci_config_erp, - .config_ant = rt2800pci_config_ant, - .config = rt2800pci_config, + .config_shared_key = rt2800_config_shared_key, + .config_pairwise_key = rt2800_config_pairwise_key, + .config_filter = rt2800_config_filter, + .config_intf = rt2800_config_intf, + .config_erp = rt2800_config_erp, + .config_ant = rt2800_config_ant, + .config = rt2800_config, }; static const struct data_queue_desc rt2800pci_queue_rx = { @@ -3213,9 +1575,9 @@ static const struct rt2x00_ops rt2800pci_ops = { .tx = &rt2800pci_queue_tx, .bcn = &rt2800pci_queue_bcn, .lib = &rt2800pci_rt2x00_ops, - .hw = &rt2800pci_mac80211_ops, + .hw = &rt2800_mac80211_ops, #ifdef CONFIG_RT2X00_LIB_DEBUGFS - .debugfs = &rt2800pci_rt2x00debug, + .debugfs = &rt2800_rt2x00debug, #endif /* CONFIG_RT2X00_LIB_DEBUGFS */ }; diff --git a/drivers/net/wireless/rt2x00/rt2800pci.h b/drivers/net/wireless/rt2x00/rt2800pci.h index 8569088..1dbf132 100644 --- a/drivers/net/wireless/rt2x00/rt2800pci.h +++ b/drivers/net/wireless/rt2x00/rt2800pci.h @@ -28,61 +28,6 @@ #define RT2800PCI_H /* - * RF chip defines. - * - * RF2820 2.4G 2T3R - * RF2850 2.4G/5G 2T3R - * RF2720 2.4G 1T2R - * RF2750 2.4G/5G 1T2R - * RF3020 2.4G 1T1R - * RF2020 2.4G B/G - * RF3021 2.4G 1T2R - * RF3022 2.4G 2T2R - * RF3052 2.4G 2T2R - */ -#define RF2820 0x0001 -#define RF2850 0x0002 -#define RF2720 0x0003 -#define RF2750 0x0004 -#define RF3020 0x0005 -#define RF2020 0x0006 -#define RF3021 0x0007 -#define RF3022 0x0008 -#define RF3052 0x0009 - -/* - * RT2860 version - */ -#define RT2860C_VERSION 0x28600100 -#define RT2860D_VERSION 0x28600101 -#define RT2880E_VERSION 0x28720200 -#define RT2883_VERSION 0x28830300 -#define RT3070_VERSION 0x30700200 - -/* - * Signal information. - * Default offset is required for RSSI <-> dBm conversion. - */ -#define DEFAULT_RSSI_OFFSET 120 /* FIXME */ - -/* - * Register layout information. - */ -#define CSR_REG_BASE 0x1000 -#define CSR_REG_SIZE 0x0800 -#define EEPROM_BASE 0x0000 -#define EEPROM_SIZE 0x0110 -#define BBP_BASE 0x0000 -#define BBP_SIZE 0x0080 -#define RF_BASE 0x0004 -#define RF_SIZE 0x0010 - -/* - * Number of TX queues. - */ -#define NUM_TX_QUEUES 4 - -/* * PCI registers. */ @@ -102,215 +47,6 @@ #define E2PROM_CSR_RELOAD FIELD32(0x00000080) /* - * INT_SOURCE_CSR: Interrupt source register. - * Write one to clear corresponding bit. - * TX_FIFO_STATUS: FIFO Statistics is full, sw should read 0x171c - */ -#define INT_SOURCE_CSR 0x0200 -#define INT_SOURCE_CSR_RXDELAYINT FIELD32(0x00000001) -#define INT_SOURCE_CSR_TXDELAYINT FIELD32(0x00000002) -#define INT_SOURCE_CSR_RX_DONE FIELD32(0x00000004) -#define INT_SOURCE_CSR_AC0_DMA_DONE FIELD32(0x00000008) -#define INT_SOURCE_CSR_AC1_DMA_DONE FIELD32(0x00000010) -#define INT_SOURCE_CSR_AC2_DMA_DONE FIELD32(0x00000020) -#define INT_SOURCE_CSR_AC3_DMA_DONE FIELD32(0x00000040) -#define INT_SOURCE_CSR_HCCA_DMA_DONE FIELD32(0x00000080) -#define INT_SOURCE_CSR_MGMT_DMA_DONE FIELD32(0x00000100) -#define INT_SOURCE_CSR_MCU_COMMAND FIELD32(0x00000200) -#define INT_SOURCE_CSR_RXTX_COHERENT FIELD32(0x00000400) -#define INT_SOURCE_CSR_TBTT FIELD32(0x00000800) -#define INT_SOURCE_CSR_PRE_TBTT FIELD32(0x00001000) -#define INT_SOURCE_CSR_TX_FIFO_STATUS FIELD32(0x00002000) -#define INT_SOURCE_CSR_AUTO_WAKEUP FIELD32(0x00004000) -#define INT_SOURCE_CSR_GPTIMER FIELD32(0x00008000) -#define INT_SOURCE_CSR_RX_COHERENT FIELD32(0x00010000) -#define INT_SOURCE_CSR_TX_COHERENT FIELD32(0x00020000) - -/* - * INT_MASK_CSR: Interrupt MASK register. 1: the interrupt is mask OFF. - */ -#define INT_MASK_CSR 0x0204 -#define INT_MASK_CSR_RXDELAYINT FIELD32(0x00000001) -#define INT_MASK_CSR_TXDELAYINT FIELD32(0x00000002) -#define INT_MASK_CSR_RX_DONE FIELD32(0x00000004) -#define INT_MASK_CSR_AC0_DMA_DONE FIELD32(0x00000008) -#define INT_MASK_CSR_AC1_DMA_DONE FIELD32(0x00000010) -#define INT_MASK_CSR_AC2_DMA_DONE FIELD32(0x00000020) -#define INT_MASK_CSR_AC3_DMA_DONE FIELD32(0x00000040) -#define INT_MASK_CSR_HCCA_DMA_DONE FIELD32(0x00000080) -#define INT_MASK_CSR_MGMT_DMA_DONE FIELD32(0x00000100) -#define INT_MASK_CSR_MCU_COMMAND FIELD32(0x00000200) -#define INT_MASK_CSR_RXTX_COHERENT FIELD32(0x00000400) -#define INT_MASK_CSR_TBTT FIELD32(0x00000800) -#define INT_MASK_CSR_PRE_TBTT FIELD32(0x00001000) -#define INT_MASK_CSR_TX_FIFO_STATUS FIELD32(0x00002000) -#define INT_MASK_CSR_AUTO_WAKEUP FIELD32(0x00004000) -#define INT_MASK_CSR_GPTIMER FIELD32(0x00008000) -#define INT_MASK_CSR_RX_COHERENT FIELD32(0x00010000) -#define INT_MASK_CSR_TX_COHERENT FIELD32(0x00020000) - -/* - * WPDMA_GLO_CFG - */ -#define WPDMA_GLO_CFG 0x0208 -#define WPDMA_GLO_CFG_ENABLE_TX_DMA FIELD32(0x00000001) -#define WPDMA_GLO_CFG_TX_DMA_BUSY FIELD32(0x00000002) -#define WPDMA_GLO_CFG_ENABLE_RX_DMA FIELD32(0x00000004) -#define WPDMA_GLO_CFG_RX_DMA_BUSY FIELD32(0x00000008) -#define WPDMA_GLO_CFG_WP_DMA_BURST_SIZE FIELD32(0x00000030) -#define WPDMA_GLO_CFG_TX_WRITEBACK_DONE FIELD32(0x00000040) -#define WPDMA_GLO_CFG_BIG_ENDIAN FIELD32(0x00000080) -#define WPDMA_GLO_CFG_RX_HDR_SCATTER FIELD32(0x0000ff00) -#define WPDMA_GLO_CFG_HDR_SEG_LEN FIELD32(0xffff0000) - -/* - * WPDMA_RST_IDX - */ -#define WPDMA_RST_IDX 0x020c -#define WPDMA_RST_IDX_DTX_IDX0 FIELD32(0x00000001) -#define WPDMA_RST_IDX_DTX_IDX1 FIELD32(0x00000002) -#define WPDMA_RST_IDX_DTX_IDX2 FIELD32(0x00000004) -#define WPDMA_RST_IDX_DTX_IDX3 FIELD32(0x00000008) -#define WPDMA_RST_IDX_DTX_IDX4 FIELD32(0x00000010) -#define WPDMA_RST_IDX_DTX_IDX5 FIELD32(0x00000020) -#define WPDMA_RST_IDX_DRX_IDX0 FIELD32(0x00010000) - -/* - * DELAY_INT_CFG - */ -#define DELAY_INT_CFG 0x0210 -#define DELAY_INT_CFG_RXMAX_PTIME FIELD32(0x000000ff) -#define DELAY_INT_CFG_RXMAX_PINT FIELD32(0x00007f00) -#define DELAY_INT_CFG_RXDLY_INT_EN FIELD32(0x00008000) -#define DELAY_INT_CFG_TXMAX_PTIME FIELD32(0x00ff0000) -#define DELAY_INT_CFG_TXMAX_PINT FIELD32(0x7f000000) -#define DELAY_INT_CFG_TXDLY_INT_EN FIELD32(0x80000000) - -/* - * WMM_AIFSN_CFG: Aifsn for each EDCA AC - * AIFSN0: AC_BE - * AIFSN1: AC_BK - * AIFSN1: AC_VI - * AIFSN1: AC_VO - */ -#define WMM_AIFSN_CFG 0x0214 -#define WMM_AIFSN_CFG_AIFSN0 FIELD32(0x0000000f) -#define WMM_AIFSN_CFG_AIFSN1 FIELD32(0x000000f0) -#define WMM_AIFSN_CFG_AIFSN2 FIELD32(0x00000f00) -#define WMM_AIFSN_CFG_AIFSN3 FIELD32(0x0000f000) - -/* - * WMM_CWMIN_CSR: CWmin for each EDCA AC - * CWMIN0: AC_BE - * CWMIN1: AC_BK - * CWMIN1: AC_VI - * CWMIN1: AC_VO - */ -#define WMM_CWMIN_CFG 0x0218 -#define WMM_CWMIN_CFG_CWMIN0 FIELD32(0x0000000f) -#define WMM_CWMIN_CFG_CWMIN1 FIELD32(0x000000f0) -#define WMM_CWMIN_CFG_CWMIN2 FIELD32(0x00000f00) -#define WMM_CWMIN_CFG_CWMIN3 FIELD32(0x0000f000) - -/* - * WMM_CWMAX_CSR: CWmax for each EDCA AC - * CWMAX0: AC_BE - * CWMAX1: AC_BK - * CWMAX1: AC_VI - * CWMAX1: AC_VO - */ -#define WMM_CWMAX_CFG 0x021c -#define WMM_CWMAX_CFG_CWMAX0 FIELD32(0x0000000f) -#define WMM_CWMAX_CFG_CWMAX1 FIELD32(0x000000f0) -#define WMM_CWMAX_CFG_CWMAX2 FIELD32(0x00000f00) -#define WMM_CWMAX_CFG_CWMAX3 FIELD32(0x0000f000) - -/* - * AC_TXOP0: AC_BK/AC_BE TXOP register - * AC0TXOP: AC_BK in unit of 32us - * AC1TXOP: AC_BE in unit of 32us - */ -#define WMM_TXOP0_CFG 0x0220 -#define WMM_TXOP0_CFG_AC0TXOP FIELD32(0x0000ffff) -#define WMM_TXOP0_CFG_AC1TXOP FIELD32(0xffff0000) - -/* - * AC_TXOP1: AC_VO/AC_VI TXOP register - * AC2TXOP: AC_VI in unit of 32us - * AC3TXOP: AC_VO in unit of 32us - */ -#define WMM_TXOP1_CFG 0x0224 -#define WMM_TXOP1_CFG_AC2TXOP FIELD32(0x0000ffff) -#define WMM_TXOP1_CFG_AC3TXOP FIELD32(0xffff0000) - -/* - * GPIO_CTRL_CFG: - */ -#define GPIO_CTRL_CFG 0x0228 -#define GPIO_CTRL_CFG_BIT0 FIELD32(0x00000001) -#define GPIO_CTRL_CFG_BIT1 FIELD32(0x00000002) -#define GPIO_CTRL_CFG_BIT2 FIELD32(0x00000004) -#define GPIO_CTRL_CFG_BIT3 FIELD32(0x00000008) -#define GPIO_CTRL_CFG_BIT4 FIELD32(0x00000010) -#define GPIO_CTRL_CFG_BIT5 FIELD32(0x00000020) -#define GPIO_CTRL_CFG_BIT6 FIELD32(0x00000040) -#define GPIO_CTRL_CFG_BIT7 FIELD32(0x00000080) -#define GPIO_CTRL_CFG_BIT8 FIELD32(0x00000100) - -/* - * MCU_CMD_CFG - */ -#define MCU_CMD_CFG 0x022c - -/* - * AC_BK register offsets - */ -#define TX_BASE_PTR0 0x0230 -#define TX_MAX_CNT0 0x0234 -#define TX_CTX_IDX0 0x0238 -#define TX_DTX_IDX0 0x023c - -/* - * AC_BE register offsets - */ -#define TX_BASE_PTR1 0x0240 -#define TX_MAX_CNT1 0x0244 -#define TX_CTX_IDX1 0x0248 -#define TX_DTX_IDX1 0x024c - -/* - * AC_VI register offsets - */ -#define TX_BASE_PTR2 0x0250 -#define TX_MAX_CNT2 0x0254 -#define TX_CTX_IDX2 0x0258 -#define TX_DTX_IDX2 0x025c - -/* - * AC_VO register offsets - */ -#define TX_BASE_PTR3 0x0260 -#define TX_MAX_CNT3 0x0264 -#define TX_CTX_IDX3 0x0268 -#define TX_DTX_IDX3 0x026c - -/* - * HCCA register offsets - */ -#define TX_BASE_PTR4 0x0270 -#define TX_MAX_CNT4 0x0274 -#define TX_CTX_IDX4 0x0278 -#define TX_DTX_IDX4 0x027c - -/* - * MGMT register offsets - */ -#define TX_BASE_PTR5 0x0280 -#define TX_MAX_CNT5 0x0284 -#define TX_CTX_IDX5 0x0288 -#define TX_DTX_IDX5 0x028c - -/* * Queue register offset macros */ #define TX_QUEUE_REG_OFFSET 0x10 @@ -320,72 +56,6 @@ #define TX_DTX_IDX(__x) TX_DTX_IDX0 + ((__x) * TX_QUEUE_REG_OFFSET) /* - * RX register offsets - */ -#define RX_BASE_PTR 0x0290 -#define RX_MAX_CNT 0x0294 -#define RX_CRX_IDX 0x0298 -#define RX_DRX_IDX 0x029c - -/* - * PBF_SYS_CTRL - * HOST_RAM_WRITE: enable Host program ram write selection - */ -#define PBF_SYS_CTRL 0x0400 -#define PBF_SYS_CTRL_READY FIELD32(0x00000080) -#define PBF_SYS_CTRL_HOST_RAM_WRITE FIELD32(0x00010000) - -/* - * HOST-MCU shared memory - */ -#define HOST_CMD_CSR 0x0404 -#define HOST_CMD_CSR_HOST_COMMAND FIELD32(0x000000ff) - -/* - * PBF registers - * Most are for debug. Driver doesn't touch PBF register. - */ -#define PBF_CFG 0x0408 -#define PBF_MAX_PCNT 0x040c -#define PBF_CTRL 0x0410 -#define PBF_INT_STA 0x0414 -#define PBF_INT_ENA 0x0418 - -/* - * BCN_OFFSET0: - */ -#define BCN_OFFSET0 0x042c -#define BCN_OFFSET0_BCN0 FIELD32(0x000000ff) -#define BCN_OFFSET0_BCN1 FIELD32(0x0000ff00) -#define BCN_OFFSET0_BCN2 FIELD32(0x00ff0000) -#define BCN_OFFSET0_BCN3 FIELD32(0xff000000) - -/* - * BCN_OFFSET1: - */ -#define BCN_OFFSET1 0x0430 -#define BCN_OFFSET1_BCN4 FIELD32(0x000000ff) -#define BCN_OFFSET1_BCN5 FIELD32(0x0000ff00) -#define BCN_OFFSET1_BCN6 FIELD32(0x00ff0000) -#define BCN_OFFSET1_BCN7 FIELD32(0xff000000) - -/* - * PBF registers - * Most are for debug. Driver doesn't touch PBF register. - */ -#define TXRXQ_PCNT 0x0438 -#define PBF_DBG 0x043c - -/* - * RF registers - */ -#define RF_CSR_CFG 0x0500 -#define RF_CSR_CFG_DATA FIELD32(0x000000ff) -#define RF_CSR_CFG_REGNUM FIELD32(0x00001f00) -#define RF_CSR_CFG_WRITE FIELD32(0x00010000) -#define RF_CSR_CFG_BUSY FIELD32(0x00020000) - -/* * EFUSE_CSR: RT3090 EEPROM */ #define EFUSE_CTRL 0x0580 @@ -414,1360 +84,16 @@ #define EFUSE_DATA3 0x059c /* - * MAC Control/Status Registers(CSR). - * Some values are set in TU, whereas 1 TU == 1024 us. - */ - -/* - * MAC_CSR0: ASIC revision number. - * ASIC_REV: 0 - * ASIC_VER: 2860 - */ -#define MAC_CSR0 0x1000 -#define MAC_CSR0_ASIC_REV FIELD32(0x0000ffff) -#define MAC_CSR0_ASIC_VER FIELD32(0xffff0000) - -/* - * MAC_SYS_CTRL: - */ -#define MAC_SYS_CTRL 0x1004 -#define MAC_SYS_CTRL_RESET_CSR FIELD32(0x00000001) -#define MAC_SYS_CTRL_RESET_BBP FIELD32(0x00000002) -#define MAC_SYS_CTRL_ENABLE_TX FIELD32(0x00000004) -#define MAC_SYS_CTRL_ENABLE_RX FIELD32(0x00000008) -#define MAC_SYS_CTRL_CONTINUOUS_TX FIELD32(0x00000010) -#define MAC_SYS_CTRL_LOOPBACK FIELD32(0x00000020) -#define MAC_SYS_CTRL_WLAN_HALT FIELD32(0x00000040) -#define MAC_SYS_CTRL_RX_TIMESTAMP FIELD32(0x00000080) - -/* - * MAC_ADDR_DW0: STA MAC register 0 - */ -#define MAC_ADDR_DW0 0x1008 -#define MAC_ADDR_DW0_BYTE0 FIELD32(0x000000ff) -#define MAC_ADDR_DW0_BYTE1 FIELD32(0x0000ff00) -#define MAC_ADDR_DW0_BYTE2 FIELD32(0x00ff0000) -#define MAC_ADDR_DW0_BYTE3 FIELD32(0xff000000) - -/* - * MAC_ADDR_DW1: STA MAC register 1 - * UNICAST_TO_ME_MASK: - * Used to mask off bits from byte 5 of the MAC address - * to determine the UNICAST_TO_ME bit for RX frames. - * The full mask is complemented by BSS_ID_MASK: - * MASK = BSS_ID_MASK & UNICAST_TO_ME_MASK - */ -#define MAC_ADDR_DW1 0x100c -#define MAC_ADDR_DW1_BYTE4 FIELD32(0x000000ff) -#define MAC_ADDR_DW1_BYTE5 FIELD32(0x0000ff00) -#define MAC_ADDR_DW1_UNICAST_TO_ME_MASK FIELD32(0x00ff0000) - -/* - * MAC_BSSID_DW0: BSSID register 0 - */ -#define MAC_BSSID_DW0 0x1010 -#define MAC_BSSID_DW0_BYTE0 FIELD32(0x000000ff) -#define MAC_BSSID_DW0_BYTE1 FIELD32(0x0000ff00) -#define MAC_BSSID_DW0_BYTE2 FIELD32(0x00ff0000) -#define MAC_BSSID_DW0_BYTE3 FIELD32(0xff000000) - -/* - * MAC_BSSID_DW1: BSSID register 1 - * BSS_ID_MASK: - * 0: 1-BSSID mode (BSS index = 0) - * 1: 2-BSSID mode (BSS index: Byte5, bit 0) - * 2: 4-BSSID mode (BSS index: byte5, bit 0 - 1) - * 3: 8-BSSID mode (BSS index: byte5, bit 0 - 2) - * This mask is used to mask off bits 0, 1 and 2 of byte 5 of the - * BSSID. This will make sure that those bits will be ignored - * when determining the MY_BSS of RX frames. - */ -#define MAC_BSSID_DW1 0x1014 -#define MAC_BSSID_DW1_BYTE4 FIELD32(0x000000ff) -#define MAC_BSSID_DW1_BYTE5 FIELD32(0x0000ff00) -#define MAC_BSSID_DW1_BSS_ID_MASK FIELD32(0x00030000) -#define MAC_BSSID_DW1_BSS_BCN_NUM FIELD32(0x001c0000) - -/* - * MAX_LEN_CFG: Maximum frame length register. - * MAX_MPDU: rt2860b max 16k bytes - * MAX_PSDU: Maximum PSDU length - * (power factor) 0:2^13, 1:2^14, 2:2^15, 3:2^16 - */ -#define MAX_LEN_CFG 0x1018 -#define MAX_LEN_CFG_MAX_MPDU FIELD32(0x00000fff) -#define MAX_LEN_CFG_MAX_PSDU FIELD32(0x00003000) -#define MAX_LEN_CFG_MIN_PSDU FIELD32(0x0000c000) -#define MAX_LEN_CFG_MIN_MPDU FIELD32(0x000f0000) - -/* - * BBP_CSR_CFG: BBP serial control register - * VALUE: Register value to program into BBP - * REG_NUM: Selected BBP register - * READ_CONTROL: 0 write BBP, 1 read BBP - * BUSY: ASIC is busy executing BBP commands - * BBP_PAR_DUR: 0 4 MAC clocks, 1 8 MAC clocks - * BBP_RW_MODE: 0 serial, 1 paralell - */ -#define BBP_CSR_CFG 0x101c -#define BBP_CSR_CFG_VALUE FIELD32(0x000000ff) -#define BBP_CSR_CFG_REGNUM FIELD32(0x0000ff00) -#define BBP_CSR_CFG_READ_CONTROL FIELD32(0x00010000) -#define BBP_CSR_CFG_BUSY FIELD32(0x00020000) -#define BBP_CSR_CFG_BBP_PAR_DUR FIELD32(0x00040000) -#define BBP_CSR_CFG_BBP_RW_MODE FIELD32(0x00080000) - -/* - * RF_CSR_CFG0: RF control register - * REGID_AND_VALUE: Register value to program into RF - * BITWIDTH: Selected RF register - * STANDBYMODE: 0 high when standby, 1 low when standby - * SEL: 0 RF_LE0 activate, 1 RF_LE1 activate - * BUSY: ASIC is busy executing RF commands - */ -#define RF_CSR_CFG0 0x1020 -#define RF_CSR_CFG0_REGID_AND_VALUE FIELD32(0x00ffffff) -#define RF_CSR_CFG0_BITWIDTH FIELD32(0x1f000000) -#define RF_CSR_CFG0_REG_VALUE_BW FIELD32(0x1fffffff) -#define RF_CSR_CFG0_STANDBYMODE FIELD32(0x20000000) -#define RF_CSR_CFG0_SEL FIELD32(0x40000000) -#define RF_CSR_CFG0_BUSY FIELD32(0x80000000) - -/* - * RF_CSR_CFG1: RF control register - * REGID_AND_VALUE: Register value to program into RF - * RFGAP: Gap between BB_CONTROL_RF and RF_LE - * 0: 3 system clock cycle (37.5usec) - * 1: 5 system clock cycle (62.5usec) - */ -#define RF_CSR_CFG1 0x1024 -#define RF_CSR_CFG1_REGID_AND_VALUE FIELD32(0x00ffffff) -#define RF_CSR_CFG1_RFGAP FIELD32(0x1f000000) - -/* - * RF_CSR_CFG2: RF control register - * VALUE: Register value to program into RF - * RFGAP: Gap between BB_CONTROL_RF and RF_LE - * 0: 3 system clock cycle (37.5usec) - * 1: 5 system clock cycle (62.5usec) - */ -#define RF_CSR_CFG2 0x1028 -#define RF_CSR_CFG2_VALUE FIELD32(0x00ffffff) - -/* - * LED_CFG: LED control - * color LED's: - * 0: off - * 1: blinking upon TX2 - * 2: periodic slow blinking - * 3: always on - * LED polarity: - * 0: active low - * 1: active high - */ -#define LED_CFG 0x102c -#define LED_CFG_ON_PERIOD FIELD32(0x000000ff) -#define LED_CFG_OFF_PERIOD FIELD32(0x0000ff00) -#define LED_CFG_SLOW_BLINK_PERIOD FIELD32(0x003f0000) -#define LED_CFG_R_LED_MODE FIELD32(0x03000000) -#define LED_CFG_G_LED_MODE FIELD32(0x0c000000) -#define LED_CFG_Y_LED_MODE FIELD32(0x30000000) -#define LED_CFG_LED_POLAR FIELD32(0x40000000) - -/* - * XIFS_TIME_CFG: MAC timing - * CCKM_SIFS_TIME: unit 1us. Applied after CCK RX/TX - * OFDM_SIFS_TIME: unit 1us. Applied after OFDM RX/TX - * OFDM_XIFS_TIME: unit 1us. Applied after OFDM RX - * when MAC doesn't reference BBP signal BBRXEND - * EIFS: unit 1us - * BB_RXEND_ENABLE: reference RXEND signal to begin XIFS defer - * - */ -#define XIFS_TIME_CFG 0x1100 -#define XIFS_TIME_CFG_CCKM_SIFS_TIME FIELD32(0x000000ff) -#define XIFS_TIME_CFG_OFDM_SIFS_TIME FIELD32(0x0000ff00) -#define XIFS_TIME_CFG_OFDM_XIFS_TIME FIELD32(0x000f0000) -#define XIFS_TIME_CFG_EIFS FIELD32(0x1ff00000) -#define XIFS_TIME_CFG_BB_RXEND_ENABLE FIELD32(0x20000000) - -/* - * BKOFF_SLOT_CFG: - */ -#define BKOFF_SLOT_CFG 0x1104 -#define BKOFF_SLOT_CFG_SLOT_TIME FIELD32(0x000000ff) -#define BKOFF_SLOT_CFG_CC_DELAY_TIME FIELD32(0x0000ff00) - -/* - * NAV_TIME_CFG: - */ -#define NAV_TIME_CFG 0x1108 -#define NAV_TIME_CFG_SIFS FIELD32(0x000000ff) -#define NAV_TIME_CFG_SLOT_TIME FIELD32(0x0000ff00) -#define NAV_TIME_CFG_EIFS FIELD32(0x01ff0000) -#define NAV_TIME_ZERO_SIFS FIELD32(0x02000000) - -/* - * CH_TIME_CFG: count as channel busy - */ -#define CH_TIME_CFG 0x110c - -/* - * PBF_LIFE_TIMER: TX/RX MPDU timestamp timer (free run) Unit: 1us - */ -#define PBF_LIFE_TIMER 0x1110 - -/* - * BCN_TIME_CFG: - * BEACON_INTERVAL: in unit of 1/16 TU - * TSF_TICKING: Enable TSF auto counting - * TSF_SYNC: Enable TSF sync, 00: disable, 01: infra mode, 10: ad-hoc mode - * BEACON_GEN: Enable beacon generator - */ -#define BCN_TIME_CFG 0x1114 -#define BCN_TIME_CFG_BEACON_INTERVAL FIELD32(0x0000ffff) -#define BCN_TIME_CFG_TSF_TICKING FIELD32(0x00010000) -#define BCN_TIME_CFG_TSF_SYNC FIELD32(0x00060000) -#define BCN_TIME_CFG_TBTT_ENABLE FIELD32(0x00080000) -#define BCN_TIME_CFG_BEACON_GEN FIELD32(0x00100000) -#define BCN_TIME_CFG_TX_TIME_COMPENSATE FIELD32(0xf0000000) - -/* - * TBTT_SYNC_CFG: - */ -#define TBTT_SYNC_CFG 0x1118 - -/* - * TSF_TIMER_DW0: Local lsb TSF timer, read-only - */ -#define TSF_TIMER_DW0 0x111c -#define TSF_TIMER_DW0_LOW_WORD FIELD32(0xffffffff) - -/* - * TSF_TIMER_DW1: Local msb TSF timer, read-only - */ -#define TSF_TIMER_DW1 0x1120 -#define TSF_TIMER_DW1_HIGH_WORD FIELD32(0xffffffff) - -/* - * TBTT_TIMER: TImer remains till next TBTT, read-only - */ -#define TBTT_TIMER 0x1124 - -/* - * INT_TIMER_CFG: - */ -#define INT_TIMER_CFG 0x1128 - -/* - * INT_TIMER_EN: GP-timer and pre-tbtt Int enable - */ -#define INT_TIMER_EN 0x112c - -/* - * CH_IDLE_STA: channel idle time - */ -#define CH_IDLE_STA 0x1130 - -/* - * CH_BUSY_STA: channel busy time - */ -#define CH_BUSY_STA 0x1134 - -/* - * MAC_STATUS_CFG: - * BBP_RF_BUSY: When set to 0, BBP and RF are stable. - * if 1 or higher one of the 2 registers is busy. - */ -#define MAC_STATUS_CFG 0x1200 -#define MAC_STATUS_CFG_BBP_RF_BUSY FIELD32(0x00000003) - -/* - * PWR_PIN_CFG: - */ -#define PWR_PIN_CFG 0x1204 - -/* - * AUTOWAKEUP_CFG: Manual power control / status register - * TBCN_BEFORE_WAKE: ForceWake has high privilege than PutToSleep when both set - * AUTOWAKE: 0:sleep, 1:awake - */ -#define AUTOWAKEUP_CFG 0x1208 -#define AUTOWAKEUP_CFG_AUTO_LEAD_TIME FIELD32(0x000000ff) -#define AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE FIELD32(0x00007f00) -#define AUTOWAKEUP_CFG_AUTOWAKE FIELD32(0x00008000) - -/* - * EDCA_AC0_CFG: - */ -#define EDCA_AC0_CFG 0x1300 -#define EDCA_AC0_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC0_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC0_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC0_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_AC1_CFG: - */ -#define EDCA_AC1_CFG 0x1304 -#define EDCA_AC1_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC1_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC1_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC1_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_AC2_CFG: - */ -#define EDCA_AC2_CFG 0x1308 -#define EDCA_AC2_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC2_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC2_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC2_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_AC3_CFG: - */ -#define EDCA_AC3_CFG 0x130c -#define EDCA_AC3_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC3_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC3_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC3_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_TID_AC_MAP: - */ -#define EDCA_TID_AC_MAP 0x1310 - -/* - * TX_PWR_CFG_0: - */ -#define TX_PWR_CFG_0 0x1314 -#define TX_PWR_CFG_0_1MBS FIELD32(0x0000000f) -#define TX_PWR_CFG_0_2MBS FIELD32(0x000000f0) -#define TX_PWR_CFG_0_55MBS FIELD32(0x00000f00) -#define TX_PWR_CFG_0_11MBS FIELD32(0x0000f000) -#define TX_PWR_CFG_0_6MBS FIELD32(0x000f0000) -#define TX_PWR_CFG_0_9MBS FIELD32(0x00f00000) -#define TX_PWR_CFG_0_12MBS FIELD32(0x0f000000) -#define TX_PWR_CFG_0_18MBS FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_1: - */ -#define TX_PWR_CFG_1 0x1318 -#define TX_PWR_CFG_1_24MBS FIELD32(0x0000000f) -#define TX_PWR_CFG_1_36MBS FIELD32(0x000000f0) -#define TX_PWR_CFG_1_48MBS FIELD32(0x00000f00) -#define TX_PWR_CFG_1_54MBS FIELD32(0x0000f000) -#define TX_PWR_CFG_1_MCS0 FIELD32(0x000f0000) -#define TX_PWR_CFG_1_MCS1 FIELD32(0x00f00000) -#define TX_PWR_CFG_1_MCS2 FIELD32(0x0f000000) -#define TX_PWR_CFG_1_MCS3 FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_2: - */ -#define TX_PWR_CFG_2 0x131c -#define TX_PWR_CFG_2_MCS4 FIELD32(0x0000000f) -#define TX_PWR_CFG_2_MCS5 FIELD32(0x000000f0) -#define TX_PWR_CFG_2_MCS6 FIELD32(0x00000f00) -#define TX_PWR_CFG_2_MCS7 FIELD32(0x0000f000) -#define TX_PWR_CFG_2_MCS8 FIELD32(0x000f0000) -#define TX_PWR_CFG_2_MCS9 FIELD32(0x00f00000) -#define TX_PWR_CFG_2_MCS10 FIELD32(0x0f000000) -#define TX_PWR_CFG_2_MCS11 FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_3: - */ -#define TX_PWR_CFG_3 0x1320 -#define TX_PWR_CFG_3_MCS12 FIELD32(0x0000000f) -#define TX_PWR_CFG_3_MCS13 FIELD32(0x000000f0) -#define TX_PWR_CFG_3_MCS14 FIELD32(0x00000f00) -#define TX_PWR_CFG_3_MCS15 FIELD32(0x0000f000) -#define TX_PWR_CFG_3_UKNOWN1 FIELD32(0x000f0000) -#define TX_PWR_CFG_3_UKNOWN2 FIELD32(0x00f00000) -#define TX_PWR_CFG_3_UKNOWN3 FIELD32(0x0f000000) -#define TX_PWR_CFG_3_UKNOWN4 FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_4: - */ -#define TX_PWR_CFG_4 0x1324 -#define TX_PWR_CFG_4_UKNOWN5 FIELD32(0x0000000f) -#define TX_PWR_CFG_4_UKNOWN6 FIELD32(0x000000f0) -#define TX_PWR_CFG_4_UKNOWN7 FIELD32(0x00000f00) -#define TX_PWR_CFG_4_UKNOWN8 FIELD32(0x0000f000) - -/* - * TX_PIN_CFG: - */ -#define TX_PIN_CFG 0x1328 -#define TX_PIN_CFG_PA_PE_A0_EN FIELD32(0x00000001) -#define TX_PIN_CFG_PA_PE_G0_EN FIELD32(0x00000002) -#define TX_PIN_CFG_PA_PE_A1_EN FIELD32(0x00000004) -#define TX_PIN_CFG_PA_PE_G1_EN FIELD32(0x00000008) -#define TX_PIN_CFG_PA_PE_A0_POL FIELD32(0x00000010) -#define TX_PIN_CFG_PA_PE_G0_POL FIELD32(0x00000020) -#define TX_PIN_CFG_PA_PE_A1_POL FIELD32(0x00000040) -#define TX_PIN_CFG_PA_PE_G1_POL FIELD32(0x00000080) -#define TX_PIN_CFG_LNA_PE_A0_EN FIELD32(0x00000100) -#define TX_PIN_CFG_LNA_PE_G0_EN FIELD32(0x00000200) -#define TX_PIN_CFG_LNA_PE_A1_EN FIELD32(0x00000400) -#define TX_PIN_CFG_LNA_PE_G1_EN FIELD32(0x00000800) -#define TX_PIN_CFG_LNA_PE_A0_POL FIELD32(0x00001000) -#define TX_PIN_CFG_LNA_PE_G0_POL FIELD32(0x00002000) -#define TX_PIN_CFG_LNA_PE_A1_POL FIELD32(0x00004000) -#define TX_PIN_CFG_LNA_PE_G1_POL FIELD32(0x00008000) -#define TX_PIN_CFG_RFTR_EN FIELD32(0x00010000) -#define TX_PIN_CFG_RFTR_POL FIELD32(0x00020000) -#define TX_PIN_CFG_TRSW_EN FIELD32(0x00040000) -#define TX_PIN_CFG_TRSW_POL FIELD32(0x00080000) - -/* - * TX_BAND_CFG: 0x1 use upper 20MHz, 0x0 use lower 20MHz - */ -#define TX_BAND_CFG 0x132c -#define TX_BAND_CFG_HT40_PLUS FIELD32(0x00000001) -#define TX_BAND_CFG_A FIELD32(0x00000002) -#define TX_BAND_CFG_BG FIELD32(0x00000004) - -/* - * TX_SW_CFG0: - */ -#define TX_SW_CFG0 0x1330 - -/* - * TX_SW_CFG1: - */ -#define TX_SW_CFG1 0x1334 - -/* - * TX_SW_CFG2: - */ -#define TX_SW_CFG2 0x1338 - -/* - * TXOP_THRES_CFG: - */ -#define TXOP_THRES_CFG 0x133c - -/* - * TXOP_CTRL_CFG: - */ -#define TXOP_CTRL_CFG 0x1340 - -/* - * TX_RTS_CFG: - * RTS_THRES: unit:byte - * RTS_FBK_EN: enable rts rate fallback - */ -#define TX_RTS_CFG 0x1344 -#define TX_RTS_CFG_AUTO_RTS_RETRY_LIMIT FIELD32(0x000000ff) -#define TX_RTS_CFG_RTS_THRES FIELD32(0x00ffff00) -#define TX_RTS_CFG_RTS_FBK_EN FIELD32(0x01000000) - -/* - * TX_TIMEOUT_CFG: - * MPDU_LIFETIME: expiration time = 2^(9+MPDU LIFE TIME) us - * RX_ACK_TIMEOUT: unit:slot. Used for TX procedure - * TX_OP_TIMEOUT: TXOP timeout value for TXOP truncation. - * it is recommended that: - * (SLOT_TIME) > (TX_OP_TIMEOUT) > (RX_ACK_TIMEOUT) - */ -#define TX_TIMEOUT_CFG 0x1348 -#define TX_TIMEOUT_CFG_MPDU_LIFETIME FIELD32(0x000000f0) -#define TX_TIMEOUT_CFG_RX_ACK_TIMEOUT FIELD32(0x0000ff00) -#define TX_TIMEOUT_CFG_TX_OP_TIMEOUT FIELD32(0x00ff0000) - -/* - * TX_RTY_CFG: - * SHORT_RTY_LIMIT: short retry limit - * LONG_RTY_LIMIT: long retry limit - * LONG_RTY_THRE: Long retry threshoold - * NON_AGG_RTY_MODE: Non-Aggregate MPDU retry mode - * 0:expired by retry limit, 1: expired by mpdu life timer - * AGG_RTY_MODE: Aggregate MPDU retry mode - * 0:expired by retry limit, 1: expired by mpdu life timer - * TX_AUTO_FB_ENABLE: Tx retry PHY rate auto fallback enable - */ -#define TX_RTY_CFG 0x134c -#define TX_RTY_CFG_SHORT_RTY_LIMIT FIELD32(0x000000ff) -#define TX_RTY_CFG_LONG_RTY_LIMIT FIELD32(0x0000ff00) -#define TX_RTY_CFG_LONG_RTY_THRE FIELD32(0x0fff0000) -#define TX_RTY_CFG_NON_AGG_RTY_MODE FIELD32(0x10000000) -#define TX_RTY_CFG_AGG_RTY_MODE FIELD32(0x20000000) -#define TX_RTY_CFG_TX_AUTO_FB_ENABLE FIELD32(0x40000000) - -/* - * TX_LINK_CFG: - * REMOTE_MFB_LIFETIME: remote MFB life time. unit: 32us - * MFB_ENABLE: TX apply remote MFB 1:enable - * REMOTE_UMFS_ENABLE: remote unsolicit MFB enable - * 0: not apply remote remote unsolicit (MFS=7) - * TX_MRQ_EN: MCS request TX enable - * TX_RDG_EN: RDG TX enable - * TX_CF_ACK_EN: Piggyback CF-ACK enable - * REMOTE_MFB: remote MCS feedback - * REMOTE_MFS: remote MCS feedback sequence number - */ -#define TX_LINK_CFG 0x1350 -#define TX_LINK_CFG_REMOTE_MFB_LIFETIME FIELD32(0x000000ff) -#define TX_LINK_CFG_MFB_ENABLE FIELD32(0x00000100) -#define TX_LINK_CFG_REMOTE_UMFS_ENABLE FIELD32(0x00000200) -#define TX_LINK_CFG_TX_MRQ_EN FIELD32(0x00000400) -#define TX_LINK_CFG_TX_RDG_EN FIELD32(0x00000800) -#define TX_LINK_CFG_TX_CF_ACK_EN FIELD32(0x00001000) -#define TX_LINK_CFG_REMOTE_MFB FIELD32(0x00ff0000) -#define TX_LINK_CFG_REMOTE_MFS FIELD32(0xff000000) - -/* - * HT_FBK_CFG0: - */ -#define HT_FBK_CFG0 0x1354 -#define HT_FBK_CFG0_HTMCS0FBK FIELD32(0x0000000f) -#define HT_FBK_CFG0_HTMCS1FBK FIELD32(0x000000f0) -#define HT_FBK_CFG0_HTMCS2FBK FIELD32(0x00000f00) -#define HT_FBK_CFG0_HTMCS3FBK FIELD32(0x0000f000) -#define HT_FBK_CFG0_HTMCS4FBK FIELD32(0x000f0000) -#define HT_FBK_CFG0_HTMCS5FBK FIELD32(0x00f00000) -#define HT_FBK_CFG0_HTMCS6FBK FIELD32(0x0f000000) -#define HT_FBK_CFG0_HTMCS7FBK FIELD32(0xf0000000) - -/* - * HT_FBK_CFG1: - */ -#define HT_FBK_CFG1 0x1358 -#define HT_FBK_CFG1_HTMCS8FBK FIELD32(0x0000000f) -#define HT_FBK_CFG1_HTMCS9FBK FIELD32(0x000000f0) -#define HT_FBK_CFG1_HTMCS10FBK FIELD32(0x00000f00) -#define HT_FBK_CFG1_HTMCS11FBK FIELD32(0x0000f000) -#define HT_FBK_CFG1_HTMCS12FBK FIELD32(0x000f0000) -#define HT_FBK_CFG1_HTMCS13FBK FIELD32(0x00f00000) -#define HT_FBK_CFG1_HTMCS14FBK FIELD32(0x0f000000) -#define HT_FBK_CFG1_HTMCS15FBK FIELD32(0xf0000000) - -/* - * LG_FBK_CFG0: - */ -#define LG_FBK_CFG0 0x135c -#define LG_FBK_CFG0_OFDMMCS0FBK FIELD32(0x0000000f) -#define LG_FBK_CFG0_OFDMMCS1FBK FIELD32(0x000000f0) -#define LG_FBK_CFG0_OFDMMCS2FBK FIELD32(0x00000f00) -#define LG_FBK_CFG0_OFDMMCS3FBK FIELD32(0x0000f000) -#define LG_FBK_CFG0_OFDMMCS4FBK FIELD32(0x000f0000) -#define LG_FBK_CFG0_OFDMMCS5FBK FIELD32(0x00f00000) -#define LG_FBK_CFG0_OFDMMCS6FBK FIELD32(0x0f000000) -#define LG_FBK_CFG0_OFDMMCS7FBK FIELD32(0xf0000000) - -/* - * LG_FBK_CFG1: - */ -#define LG_FBK_CFG1 0x1360 -#define LG_FBK_CFG0_CCKMCS0FBK FIELD32(0x0000000f) -#define LG_FBK_CFG0_CCKMCS1FBK FIELD32(0x000000f0) -#define LG_FBK_CFG0_CCKMCS2FBK FIELD32(0x00000f00) -#define LG_FBK_CFG0_CCKMCS3FBK FIELD32(0x0000f000) - -/* - * CCK_PROT_CFG: CCK Protection - * PROTECT_RATE: Protection control frame rate for CCK TX(RTS/CTS/CFEnd) - * PROTECT_CTRL: Protection control frame type for CCK TX - * 0:none, 1:RTS/CTS, 2:CTS-to-self - * PROTECT_NAV: TXOP protection type for CCK TX - * 0:none, 1:ShortNAVprotect, 2:LongNAVProtect - * TX_OP_ALLOW_CCK: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_OFDM: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_MM20: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_MM40: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_GF20: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_GF40: CCK TXOP allowance, 0:disallow - * RTS_TH_EN: RTS threshold enable on CCK TX - */ -#define CCK_PROT_CFG 0x1364 -#define CCK_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define CCK_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define CCK_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define CCK_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define CCK_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define CCK_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define CCK_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define CCK_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define CCK_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define CCK_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * OFDM_PROT_CFG: OFDM Protection - */ -#define OFDM_PROT_CFG 0x1368 -#define OFDM_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define OFDM_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define OFDM_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define OFDM_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * MM20_PROT_CFG: MM20 Protection - */ -#define MM20_PROT_CFG 0x136c -#define MM20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define MM20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define MM20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define MM20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define MM20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define MM20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define MM20_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define MM20_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define MM20_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define MM20_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * MM40_PROT_CFG: MM40 Protection - */ -#define MM40_PROT_CFG 0x1370 -#define MM40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define MM40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define MM40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define MM40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define MM40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define MM40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define MM40_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define MM40_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define MM40_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define MM40_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * GF20_PROT_CFG: GF20 Protection - */ -#define GF20_PROT_CFG 0x1374 -#define GF20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define GF20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define GF20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define GF20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define GF20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define GF20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define GF20_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define GF20_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define GF20_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define GF20_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * GF40_PROT_CFG: GF40 Protection - */ -#define GF40_PROT_CFG 0x1378 -#define GF40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define GF40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define GF40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define GF40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define GF40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define GF40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define GF40_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define GF40_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define GF40_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define GF40_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * EXP_CTS_TIME: - */ -#define EXP_CTS_TIME 0x137c - -/* - * EXP_ACK_TIME: - */ -#define EXP_ACK_TIME 0x1380 - -/* - * RX_FILTER_CFG: RX configuration register. - */ -#define RX_FILTER_CFG 0x1400 -#define RX_FILTER_CFG_DROP_CRC_ERROR FIELD32(0x00000001) -#define RX_FILTER_CFG_DROP_PHY_ERROR FIELD32(0x00000002) -#define RX_FILTER_CFG_DROP_NOT_TO_ME FIELD32(0x00000004) -#define RX_FILTER_CFG_DROP_NOT_MY_BSSD FIELD32(0x00000008) -#define RX_FILTER_CFG_DROP_VER_ERROR FIELD32(0x00000010) -#define RX_FILTER_CFG_DROP_MULTICAST FIELD32(0x00000020) -#define RX_FILTER_CFG_DROP_BROADCAST FIELD32(0x00000040) -#define RX_FILTER_CFG_DROP_DUPLICATE FIELD32(0x00000080) -#define RX_FILTER_CFG_DROP_CF_END_ACK FIELD32(0x00000100) -#define RX_FILTER_CFG_DROP_CF_END FIELD32(0x00000200) -#define RX_FILTER_CFG_DROP_ACK FIELD32(0x00000400) -#define RX_FILTER_CFG_DROP_CTS FIELD32(0x00000800) -#define RX_FILTER_CFG_DROP_RTS FIELD32(0x00001000) -#define RX_FILTER_CFG_DROP_PSPOLL FIELD32(0x00002000) -#define RX_FILTER_CFG_DROP_BA FIELD32(0x00004000) -#define RX_FILTER_CFG_DROP_BAR FIELD32(0x00008000) -#define RX_FILTER_CFG_DROP_CNTL FIELD32(0x00010000) - -/* - * AUTO_RSP_CFG: - * AUTORESPONDER: 0: disable, 1: enable - * BAC_ACK_POLICY: 0:long, 1:short preamble - * CTS_40_MMODE: Response CTS 40MHz duplicate mode - * CTS_40_MREF: Response CTS 40MHz duplicate mode - * AR_PREAMBLE: Auto responder preamble 0:long, 1:short preamble - * DUAL_CTS_EN: Power bit value in control frame - * ACK_CTS_PSM_BIT:Power bit value in control frame - */ -#define AUTO_RSP_CFG 0x1404 -#define AUTO_RSP_CFG_AUTORESPONDER FIELD32(0x00000001) -#define AUTO_RSP_CFG_BAC_ACK_POLICY FIELD32(0x00000002) -#define AUTO_RSP_CFG_CTS_40_MMODE FIELD32(0x00000004) -#define AUTO_RSP_CFG_CTS_40_MREF FIELD32(0x00000008) -#define AUTO_RSP_CFG_AR_PREAMBLE FIELD32(0x00000010) -#define AUTO_RSP_CFG_DUAL_CTS_EN FIELD32(0x00000040) -#define AUTO_RSP_CFG_ACK_CTS_PSM_BIT FIELD32(0x00000080) - -/* - * LEGACY_BASIC_RATE: - */ -#define LEGACY_BASIC_RATE 0x1408 - -/* - * HT_BASIC_RATE: - */ -#define HT_BASIC_RATE 0x140c - -/* - * HT_CTRL_CFG: - */ -#define HT_CTRL_CFG 0x1410 - -/* - * SIFS_COST_CFG: - */ -#define SIFS_COST_CFG 0x1414 - -/* - * RX_PARSER_CFG: - * Set NAV for all received frames - */ -#define RX_PARSER_CFG 0x1418 - -/* - * TX_SEC_CNT0: - */ -#define TX_SEC_CNT0 0x1500 - -/* - * RX_SEC_CNT0: - */ -#define RX_SEC_CNT0 0x1504 - -/* - * CCMP_FC_MUTE: - */ -#define CCMP_FC_MUTE 0x1508 - -/* - * TXOP_HLDR_ADDR0: - */ -#define TXOP_HLDR_ADDR0 0x1600 - -/* - * TXOP_HLDR_ADDR1: - */ -#define TXOP_HLDR_ADDR1 0x1604 - -/* - * TXOP_HLDR_ET: - */ -#define TXOP_HLDR_ET 0x1608 - -/* - * QOS_CFPOLL_RA_DW0: - */ -#define QOS_CFPOLL_RA_DW0 0x160c - -/* - * QOS_CFPOLL_RA_DW1: - */ -#define QOS_CFPOLL_RA_DW1 0x1610 - -/* - * QOS_CFPOLL_QC: - */ -#define QOS_CFPOLL_QC 0x1614 - -/* - * RX_STA_CNT0: RX PLCP error count & RX CRC error count - */ -#define RX_STA_CNT0 0x1700 -#define RX_STA_CNT0_CRC_ERR FIELD32(0x0000ffff) -#define RX_STA_CNT0_PHY_ERR FIELD32(0xffff0000) - -/* - * RX_STA_CNT1: RX False CCA count & RX LONG frame count - */ -#define RX_STA_CNT1 0x1704 -#define RX_STA_CNT1_FALSE_CCA FIELD32(0x0000ffff) -#define RX_STA_CNT1_PLCP_ERR FIELD32(0xffff0000) - -/* - * RX_STA_CNT2: - */ -#define RX_STA_CNT2 0x1708 -#define RX_STA_CNT2_RX_DUPLI_COUNT FIELD32(0x0000ffff) -#define RX_STA_CNT2_RX_FIFO_OVERFLOW FIELD32(0xffff0000) - -/* - * TX_STA_CNT0: TX Beacon count - */ -#define TX_STA_CNT0 0x170c -#define TX_STA_CNT0_TX_FAIL_COUNT FIELD32(0x0000ffff) -#define TX_STA_CNT0_TX_BEACON_COUNT FIELD32(0xffff0000) - -/* - * TX_STA_CNT1: TX tx count - */ -#define TX_STA_CNT1 0x1710 -#define TX_STA_CNT1_TX_SUCCESS FIELD32(0x0000ffff) -#define TX_STA_CNT1_TX_RETRANSMIT FIELD32(0xffff0000) - -/* - * TX_STA_CNT2: TX tx count - */ -#define TX_STA_CNT2 0x1714 -#define TX_STA_CNT2_TX_ZERO_LEN_COUNT FIELD32(0x0000ffff) -#define TX_STA_CNT2_TX_UNDER_FLOW_COUNT FIELD32(0xffff0000) - -/* - * TX_STA_FIFO: TX Result for specific PID status fifo register - */ -#define TX_STA_FIFO 0x1718 -#define TX_STA_FIFO_VALID FIELD32(0x00000001) -#define TX_STA_FIFO_PID_TYPE FIELD32(0x0000001e) -#define TX_STA_FIFO_TX_SUCCESS FIELD32(0x00000020) -#define TX_STA_FIFO_TX_AGGRE FIELD32(0x00000040) -#define TX_STA_FIFO_TX_ACK_REQUIRED FIELD32(0x00000080) -#define TX_STA_FIFO_WCID FIELD32(0x0000ff00) -#define TX_STA_FIFO_MCS FIELD32(0x007f0000) -#define TX_STA_FIFO_PHYMODE FIELD32(0xc0000000) - -/* - * TX_AGG_CNT: Debug counter - */ -#define TX_AGG_CNT 0x171c -#define TX_AGG_CNT_NON_AGG_TX_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT_AGG_TX_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT0: - */ -#define TX_AGG_CNT0 0x1720 -#define TX_AGG_CNT0_AGG_SIZE_1_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT0_AGG_SIZE_2_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT1: - */ -#define TX_AGG_CNT1 0x1724 -#define TX_AGG_CNT1_AGG_SIZE_3_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT1_AGG_SIZE_4_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT2: - */ -#define TX_AGG_CNT2 0x1728 -#define TX_AGG_CNT2_AGG_SIZE_5_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT2_AGG_SIZE_6_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT3: - */ -#define TX_AGG_CNT3 0x172c -#define TX_AGG_CNT3_AGG_SIZE_7_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT3_AGG_SIZE_8_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT4: - */ -#define TX_AGG_CNT4 0x1730 -#define TX_AGG_CNT4_AGG_SIZE_9_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT4_AGG_SIZE_10_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT5: - */ -#define TX_AGG_CNT5 0x1734 -#define TX_AGG_CNT5_AGG_SIZE_11_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT5_AGG_SIZE_12_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT6: - */ -#define TX_AGG_CNT6 0x1738 -#define TX_AGG_CNT6_AGG_SIZE_13_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT6_AGG_SIZE_14_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT7: - */ -#define TX_AGG_CNT7 0x173c -#define TX_AGG_CNT7_AGG_SIZE_15_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT7_AGG_SIZE_16_COUNT FIELD32(0xffff0000) - -/* - * MPDU_DENSITY_CNT: - * TX_ZERO_DEL: TX zero length delimiter count - * RX_ZERO_DEL: RX zero length delimiter count - */ -#define MPDU_DENSITY_CNT 0x1740 -#define MPDU_DENSITY_CNT_TX_ZERO_DEL FIELD32(0x0000ffff) -#define MPDU_DENSITY_CNT_RX_ZERO_DEL FIELD32(0xffff0000) - -/* - * Security key table memory. - * MAC_WCID_BASE: 8-bytes (use only 6 bytes) * 256 entry - * PAIRWISE_KEY_TABLE_BASE: 32-byte * 256 entry - * MAC_IVEIV_TABLE_BASE: 8-byte * 256-entry - * MAC_WCID_ATTRIBUTE_BASE: 4-byte * 256-entry - * SHARED_KEY_TABLE_BASE: 32 bytes * 32-entry - * SHARED_KEY_MODE_BASE: 4 bits * 32-entry - */ -#define MAC_WCID_BASE 0x1800 -#define PAIRWISE_KEY_TABLE_BASE 0x4000 -#define MAC_IVEIV_TABLE_BASE 0x6000 -#define MAC_WCID_ATTRIBUTE_BASE 0x6800 -#define SHARED_KEY_TABLE_BASE 0x6c00 -#define SHARED_KEY_MODE_BASE 0x7000 - -#define MAC_WCID_ENTRY(__idx) \ - ( MAC_WCID_BASE + ((__idx) * sizeof(struct mac_wcid_entry)) ) -#define PAIRWISE_KEY_ENTRY(__idx) \ - ( PAIRWISE_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) ) -#define MAC_IVEIV_ENTRY(__idx) \ - ( MAC_IVEIV_TABLE_BASE + ((__idx) & sizeof(struct mac_iveiv_entry)) ) -#define MAC_WCID_ATTR_ENTRY(__idx) \ - ( MAC_WCID_ATTRIBUTE_BASE + ((__idx) * sizeof(u32)) ) -#define SHARED_KEY_ENTRY(__idx) \ - ( SHARED_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) ) -#define SHARED_KEY_MODE_ENTRY(__idx) \ - ( SHARED_KEY_MODE_BASE + ((__idx) * sizeof(u32)) ) - -struct mac_wcid_entry { - u8 mac[6]; - u8 reserved[2]; -} __attribute__ ((packed)); - -struct hw_key_entry { - u8 key[16]; - u8 tx_mic[8]; - u8 rx_mic[8]; -} __attribute__ ((packed)); - -struct mac_iveiv_entry { - u8 iv[8]; -} __attribute__ ((packed)); - -/* - * MAC_WCID_ATTRIBUTE: - */ -#define MAC_WCID_ATTRIBUTE_KEYTAB FIELD32(0x00000001) -#define MAC_WCID_ATTRIBUTE_CIPHER FIELD32(0x0000000e) -#define MAC_WCID_ATTRIBUTE_BSS_IDX FIELD32(0x00000070) -#define MAC_WCID_ATTRIBUTE_RX_WIUDF FIELD32(0x00000380) - -/* - * SHARED_KEY_MODE: - */ -#define SHARED_KEY_MODE_BSS0_KEY0 FIELD32(0x00000007) -#define SHARED_KEY_MODE_BSS0_KEY1 FIELD32(0x00000070) -#define SHARED_KEY_MODE_BSS0_KEY2 FIELD32(0x00000700) -#define SHARED_KEY_MODE_BSS0_KEY3 FIELD32(0x00007000) -#define SHARED_KEY_MODE_BSS1_KEY0 FIELD32(0x00070000) -#define SHARED_KEY_MODE_BSS1_KEY1 FIELD32(0x00700000) -#define SHARED_KEY_MODE_BSS1_KEY2 FIELD32(0x07000000) -#define SHARED_KEY_MODE_BSS1_KEY3 FIELD32(0x70000000) - -/* - * HOST-MCU communication - */ - -/* - * H2M_MAILBOX_CSR: Host-to-MCU Mailbox. - */ -#define H2M_MAILBOX_CSR 0x7010 -#define H2M_MAILBOX_CSR_ARG0 FIELD32(0x000000ff) -#define H2M_MAILBOX_CSR_ARG1 FIELD32(0x0000ff00) -#define H2M_MAILBOX_CSR_CMD_TOKEN FIELD32(0x00ff0000) -#define H2M_MAILBOX_CSR_OWNER FIELD32(0xff000000) - -/* - * H2M_MAILBOX_CID: - */ -#define H2M_MAILBOX_CID 0x7014 -#define H2M_MAILBOX_CID_CMD0 FIELD32(0x000000ff) -#define H2M_MAILBOX_CID_CMD1 FIELD32(0x0000ff00) -#define H2M_MAILBOX_CID_CMD2 FIELD32(0x00ff0000) -#define H2M_MAILBOX_CID_CMD3 FIELD32(0xff000000) - -/* - * H2M_MAILBOX_STATUS: - */ -#define H2M_MAILBOX_STATUS 0x701c - -/* - * H2M_INT_SRC: - */ -#define H2M_INT_SRC 0x7024 - -/* - * H2M_BBP_AGENT: - */ -#define H2M_BBP_AGENT 0x7028 - -/* - * MCU_LEDCS: LED control for MCU Mailbox. - */ -#define MCU_LEDCS_LED_MODE FIELD8(0x1f) -#define MCU_LEDCS_POLARITY FIELD8(0x01) - -/* - * HW_CS_CTS_BASE: - * Carrier-sense CTS frame base address. - * It's where mac stores carrier-sense frame for carrier-sense function. - */ -#define HW_CS_CTS_BASE 0x7700 - -/* - * HW_DFS_CTS_BASE: - * FS CTS frame base address. It's where mac stores CTS frame for DFS. - */ -#define HW_DFS_CTS_BASE 0x7780 - -/* - * TXRX control registers - base address 0x3000 - */ - -/* - * TXRX_CSR1: - * rt2860b UNKNOWN reg use R/O Reg Addr 0x77d0 first.. - */ -#define TXRX_CSR1 0x77d0 - -/* - * HW_DEBUG_SETTING_BASE: - * since NULL frame won't be that long (256 byte) - * We steal 16 tail bytes to save debugging settings - */ -#define HW_DEBUG_SETTING_BASE 0x77f0 -#define HW_DEBUG_SETTING_BASE2 0x7770 - -/* - * HW_BEACON_BASE - * In order to support maximum 8 MBSS and its maximum length - * is 512 bytes for each beacon - * Three section discontinue memory segments will be used. - * 1. The original region for BCN 0~3 - * 2. Extract memory from FCE table for BCN 4~5 - * 3. Extract memory from Pair-wise key table for BCN 6~7 - * It occupied those memory of wcid 238~253 for BCN 6 - * and wcid 222~237 for BCN 7 - * - * IMPORTANT NOTE: Not sure why legacy driver does this, - * but HW_BEACON_BASE7 is 0x0200 bytes below HW_BEACON_BASE6. - */ -#define HW_BEACON_BASE0 0x7800 -#define HW_BEACON_BASE1 0x7a00 -#define HW_BEACON_BASE2 0x7c00 -#define HW_BEACON_BASE3 0x7e00 -#define HW_BEACON_BASE4 0x7200 -#define HW_BEACON_BASE5 0x7400 -#define HW_BEACON_BASE6 0x5dc0 -#define HW_BEACON_BASE7 0x5bc0 - -#define HW_BEACON_OFFSET(__index) \ - ( ((__index) < 4) ? ( HW_BEACON_BASE0 + (__index * 0x0200) ) : \ - (((__index) < 6) ? ( HW_BEACON_BASE4 + ((__index - 4) * 0x0200) ) : \ - (HW_BEACON_BASE6 - ((__index - 6) * 0x0200))) ) - -/* * 8051 firmware image. */ #define FIRMWARE_RT2860 "rt2860.bin" #define FIRMWARE_IMAGE_BASE 0x2000 /* - * BBP registers. - * The wordsize of the BBP is 8 bits. - */ - -/* - * BBP 1: TX Antenna - */ -#define BBP1_TX_POWER FIELD8(0x07) -#define BBP1_TX_ANTENNA FIELD8(0x18) - -/* - * BBP 3: RX Antenna - */ -#define BBP3_RX_ANTENNA FIELD8(0x18) -#define BBP3_HT40_PLUS FIELD8(0x20) - -/* - * BBP 4: Bandwidth - */ -#define BBP4_TX_BF FIELD8(0x01) -#define BBP4_BANDWIDTH FIELD8(0x18) - -/* - * RFCSR registers - * The wordsize of the RFCSR is 8 bits. - */ - -/* - * RFCSR 6: - */ -#define RFCSR6_R FIELD8(0x03) - -/* - * RFCSR 7: - */ -#define RFCSR7_RF_TUNING FIELD8(0x01) - -/* - * RFCSR 12: - */ -#define RFCSR12_TX_POWER FIELD8(0x1f) - -/* - * RFCSR 22: - */ -#define RFCSR22_BASEBAND_LOOPBACK FIELD8(0x01) - -/* - * RFCSR 23: - */ -#define RFCSR23_FREQ_OFFSET FIELD8(0x7f) - -/* - * RFCSR 30: - */ -#define RFCSR30_RF_CALIBRATION FIELD8(0x80) - -/* - * RF registers - */ - -/* - * RF 2 - */ -#define RF2_ANTENNA_RX2 FIELD32(0x00000040) -#define RF2_ANTENNA_TX1 FIELD32(0x00004000) -#define RF2_ANTENNA_RX1 FIELD32(0x00020000) - -/* - * RF 3 - */ -#define RF3_TXPOWER_G FIELD32(0x00003e00) -#define RF3_TXPOWER_A_7DBM_BOOST FIELD32(0x00000200) -#define RF3_TXPOWER_A FIELD32(0x00003c00) - -/* - * RF 4 - */ -#define RF4_TXPOWER_G FIELD32(0x000007c0) -#define RF4_TXPOWER_A_7DBM_BOOST FIELD32(0x00000040) -#define RF4_TXPOWER_A FIELD32(0x00000780) -#define RF4_FREQ_OFFSET FIELD32(0x001f8000) -#define RF4_HT40 FIELD32(0x00200000) - -/* - * EEPROM content. - * The wordsize of the EEPROM is 16 bits. - */ - -/* - * EEPROM Version - */ -#define EEPROM_VERSION 0x0001 -#define EEPROM_VERSION_FAE FIELD16(0x00ff) -#define EEPROM_VERSION_VERSION FIELD16(0xff00) - -/* - * HW MAC address. - */ -#define EEPROM_MAC_ADDR_0 0x0002 -#define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) -#define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) -#define EEPROM_MAC_ADDR_1 0x0003 -#define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) -#define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) -#define EEPROM_MAC_ADDR_2 0x0004 -#define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) -#define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) - -/* - * EEPROM ANTENNA config - * RXPATH: 1: 1R, 2: 2R, 3: 3R - * TXPATH: 1: 1T, 2: 2T - */ -#define EEPROM_ANTENNA 0x001a -#define EEPROM_ANTENNA_RXPATH FIELD16(0x000f) -#define EEPROM_ANTENNA_TXPATH FIELD16(0x00f0) -#define EEPROM_ANTENNA_RF_TYPE FIELD16(0x0f00) - -/* - * EEPROM NIC config - * CARDBUS_ACCEL: 0 - enable, 1 - disable - */ -#define EEPROM_NIC 0x001b -#define EEPROM_NIC_HW_RADIO FIELD16(0x0001) -#define EEPROM_NIC_DYNAMIC_TX_AGC FIELD16(0x0002) -#define EEPROM_NIC_EXTERNAL_LNA_BG FIELD16(0x0004) -#define EEPROM_NIC_EXTERNAL_LNA_A FIELD16(0x0008) -#define EEPROM_NIC_CARDBUS_ACCEL FIELD16(0x0010) -#define EEPROM_NIC_BW40M_SB_BG FIELD16(0x0020) -#define EEPROM_NIC_BW40M_SB_A FIELD16(0x0040) -#define EEPROM_NIC_WPS_PBC FIELD16(0x0080) -#define EEPROM_NIC_BW40M_BG FIELD16(0x0100) -#define EEPROM_NIC_BW40M_A FIELD16(0x0200) - -/* - * EEPROM frequency - */ -#define EEPROM_FREQ 0x001d -#define EEPROM_FREQ_OFFSET FIELD16(0x00ff) -#define EEPROM_FREQ_LED_MODE FIELD16(0x7f00) -#define EEPROM_FREQ_LED_POLARITY FIELD16(0x1000) - -/* - * EEPROM LED - * POLARITY_RDY_G: Polarity RDY_G setting. - * POLARITY_RDY_A: Polarity RDY_A setting. - * POLARITY_ACT: Polarity ACT setting. - * POLARITY_GPIO_0: Polarity GPIO0 setting. - * POLARITY_GPIO_1: Polarity GPIO1 setting. - * POLARITY_GPIO_2: Polarity GPIO2 setting. - * POLARITY_GPIO_3: Polarity GPIO3 setting. - * POLARITY_GPIO_4: Polarity GPIO4 setting. - * LED_MODE: Led mode. - */ -#define EEPROM_LED1 0x001e -#define EEPROM_LED2 0x001f -#define EEPROM_LED3 0x0020 -#define EEPROM_LED_POLARITY_RDY_BG FIELD16(0x0001) -#define EEPROM_LED_POLARITY_RDY_A FIELD16(0x0002) -#define EEPROM_LED_POLARITY_ACT FIELD16(0x0004) -#define EEPROM_LED_POLARITY_GPIO_0 FIELD16(0x0008) -#define EEPROM_LED_POLARITY_GPIO_1 FIELD16(0x0010) -#define EEPROM_LED_POLARITY_GPIO_2 FIELD16(0x0020) -#define EEPROM_LED_POLARITY_GPIO_3 FIELD16(0x0040) -#define EEPROM_LED_POLARITY_GPIO_4 FIELD16(0x0080) -#define EEPROM_LED_LED_MODE FIELD16(0x1f00) - -/* - * EEPROM LNA - */ -#define EEPROM_LNA 0x0022 -#define EEPROM_LNA_BG FIELD16(0x00ff) -#define EEPROM_LNA_A0 FIELD16(0xff00) - -/* - * EEPROM RSSI BG offset - */ -#define EEPROM_RSSI_BG 0x0023 -#define EEPROM_RSSI_BG_OFFSET0 FIELD16(0x00ff) -#define EEPROM_RSSI_BG_OFFSET1 FIELD16(0xff00) - -/* - * EEPROM RSSI BG2 offset - */ -#define EEPROM_RSSI_BG2 0x0024 -#define EEPROM_RSSI_BG2_OFFSET2 FIELD16(0x00ff) -#define EEPROM_RSSI_BG2_LNA_A1 FIELD16(0xff00) - -/* - * EEPROM RSSI A offset - */ -#define EEPROM_RSSI_A 0x0025 -#define EEPROM_RSSI_A_OFFSET0 FIELD16(0x00ff) -#define EEPROM_RSSI_A_OFFSET1 FIELD16(0xff00) - -/* - * EEPROM RSSI A2 offset - */ -#define EEPROM_RSSI_A2 0x0026 -#define EEPROM_RSSI_A2_OFFSET2 FIELD16(0x00ff) -#define EEPROM_RSSI_A2_LNA_A2 FIELD16(0xff00) - -/* - * EEPROM TXpower delta: 20MHZ AND 40 MHZ use different power. - * This is delta in 40MHZ. - * VALUE: Tx Power dalta value (MAX=4) - * TYPE: 1: Plus the delta value, 0: minus the delta value - * TXPOWER: Enable: - */ -#define EEPROM_TXPOWER_DELTA 0x0028 -#define EEPROM_TXPOWER_DELTA_VALUE FIELD16(0x003f) -#define EEPROM_TXPOWER_DELTA_TYPE FIELD16(0x0040) -#define EEPROM_TXPOWER_DELTA_TXPOWER FIELD16(0x0080) - -/* - * EEPROM TXPOWER 802.11BG - */ -#define EEPROM_TXPOWER_BG1 0x0029 -#define EEPROM_TXPOWER_BG2 0x0030 -#define EEPROM_TXPOWER_BG_SIZE 7 -#define EEPROM_TXPOWER_BG_1 FIELD16(0x00ff) -#define EEPROM_TXPOWER_BG_2 FIELD16(0xff00) - -/* - * EEPROM TXPOWER 802.11A - */ -#define EEPROM_TXPOWER_A1 0x003c -#define EEPROM_TXPOWER_A2 0x0053 -#define EEPROM_TXPOWER_A_SIZE 6 -#define EEPROM_TXPOWER_A_1 FIELD16(0x00ff) -#define EEPROM_TXPOWER_A_2 FIELD16(0xff00) - -/* - * EEPROM TXpower byrate: 20MHZ power - */ -#define EEPROM_TXPOWER_BYRATE 0x006f - -/* - * EEPROM BBP. - */ -#define EEPROM_BBP_START 0x0078 -#define EEPROM_BBP_SIZE 16 -#define EEPROM_BBP_VALUE FIELD16(0x00ff) -#define EEPROM_BBP_REG_ID FIELD16(0xff00) - -/* - * MCU mailbox commands. - */ -#define MCU_SLEEP 0x30 -#define MCU_WAKEUP 0x31 -#define MCU_RADIO_OFF 0x35 -#define MCU_CURRENT 0x36 -#define MCU_LED 0x50 -#define MCU_LED_STRENGTH 0x51 -#define MCU_LED_1 0x52 -#define MCU_LED_2 0x53 -#define MCU_LED_3 0x54 -#define MCU_RADAR 0x60 -#define MCU_BOOT_SIGNAL 0x72 -#define MCU_BBP_SIGNAL 0x80 -#define MCU_POWER_SAVE 0x83 - -/* - * MCU mailbox tokens - */ -#define TOKEN_WAKUP 3 - -/* * DMA descriptor defines. */ #define TXD_DESC_SIZE ( 4 * sizeof(__le32) ) -#define TXWI_DESC_SIZE ( 4 * sizeof(__le32) ) #define RXD_DESC_SIZE ( 4 * sizeof(__le32) ) -#define RXWI_DESC_SIZE ( 4 * sizeof(__le32) ) /* * TX descriptor format for TX, PRIO and Beacon Ring. @@ -1806,52 +132,6 @@ struct mac_iveiv_entry { #define TXD_W3_ICO FIELD32(0x80000000) /* - * TX WI structure - */ - -/* - * Word0 - * FRAG: 1 To inform TKIP engine this is a fragment. - * MIMO_PS: The remote peer is in dynamic MIMO-PS mode - * TX_OP: 0:HT TXOP rule , 1:PIFS TX ,2:Backoff, 3:sifs - * BW: Channel bandwidth 20MHz or 40 MHz - * STBC: 1: STBC support MCS =0-7, 2,3 : RESERVED - */ -#define TXWI_W0_FRAG FIELD32(0x00000001) -#define TXWI_W0_MIMO_PS FIELD32(0x00000002) -#define TXWI_W0_CF_ACK FIELD32(0x00000004) -#define TXWI_W0_TS FIELD32(0x00000008) -#define TXWI_W0_AMPDU FIELD32(0x00000010) -#define TXWI_W0_MPDU_DENSITY FIELD32(0x000000e0) -#define TXWI_W0_TX_OP FIELD32(0x00000300) -#define TXWI_W0_MCS FIELD32(0x007f0000) -#define TXWI_W0_BW FIELD32(0x00800000) -#define TXWI_W0_SHORT_GI FIELD32(0x01000000) -#define TXWI_W0_STBC FIELD32(0x06000000) -#define TXWI_W0_IFS FIELD32(0x08000000) -#define TXWI_W0_PHYMODE FIELD32(0xc0000000) - -/* - * Word1 - */ -#define TXWI_W1_ACK FIELD32(0x00000001) -#define TXWI_W1_NSEQ FIELD32(0x00000002) -#define TXWI_W1_BW_WIN_SIZE FIELD32(0x000000fc) -#define TXWI_W1_WIRELESS_CLI_ID FIELD32(0x0000ff00) -#define TXWI_W1_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) -#define TXWI_W1_PACKETID FIELD32(0xf0000000) - -/* - * Word2 - */ -#define TXWI_W2_IV FIELD32(0xffffffff) - -/* - * Word3 - */ -#define TXWI_W3_EIV FIELD32(0xffffffff) - -/* * RX descriptor format for RX Ring. */ @@ -1897,64 +177,4 @@ struct mac_iveiv_entry { #define RXD_W3_PLCP_SIGNAL FIELD32(0x00020000) #define RXD_W3_PLCP_RSSI FIELD32(0x00040000) -/* - * RX WI structure - */ - -/* - * Word0 - */ -#define RXWI_W0_WIRELESS_CLI_ID FIELD32(0x000000ff) -#define RXWI_W0_KEY_INDEX FIELD32(0x00000300) -#define RXWI_W0_BSSID FIELD32(0x00001c00) -#define RXWI_W0_UDF FIELD32(0x0000e000) -#define RXWI_W0_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) -#define RXWI_W0_TID FIELD32(0xf0000000) - -/* - * Word1 - */ -#define RXWI_W1_FRAG FIELD32(0x0000000f) -#define RXWI_W1_SEQUENCE FIELD32(0x0000fff0) -#define RXWI_W1_MCS FIELD32(0x007f0000) -#define RXWI_W1_BW FIELD32(0x00800000) -#define RXWI_W1_SHORT_GI FIELD32(0x01000000) -#define RXWI_W1_STBC FIELD32(0x06000000) -#define RXWI_W1_PHYMODE FIELD32(0xc0000000) - -/* - * Word2 - */ -#define RXWI_W2_RSSI0 FIELD32(0x000000ff) -#define RXWI_W2_RSSI1 FIELD32(0x0000ff00) -#define RXWI_W2_RSSI2 FIELD32(0x00ff0000) - -/* - * Word3 - */ -#define RXWI_W3_SNR0 FIELD32(0x000000ff) -#define RXWI_W3_SNR1 FIELD32(0x0000ff00) - -/* - * Macros for converting txpower from EEPROM to mac80211 value - * and from mac80211 value to register value. - */ -#define MIN_G_TXPOWER 0 -#define MIN_A_TXPOWER -7 -#define MAX_G_TXPOWER 31 -#define MAX_A_TXPOWER 15 -#define DEFAULT_TXPOWER 5 - -#define TXPOWER_G_FROM_DEV(__txpower) \ - ((__txpower) > MAX_G_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) - -#define TXPOWER_G_TO_DEV(__txpower) \ - clamp_t(char, __txpower, MIN_G_TXPOWER, MAX_G_TXPOWER) - -#define TXPOWER_A_FROM_DEV(__txpower) \ - ((__txpower) > MAX_A_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) - -#define TXPOWER_A_TO_DEV(__txpower) \ - clamp_t(char, __txpower, MIN_A_TXPOWER, MAX_A_TXPOWER) - #endif /* RT2800PCI_H */ diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c index 9fe770f..ce2e893 100644 --- a/drivers/net/wireless/rt2x00/rt2800usb.c +++ b/drivers/net/wireless/rt2x00/rt2800usb.c @@ -34,6 +34,8 @@ #include "rt2x00.h" #include "rt2x00usb.h" +#include "rt2800lib.h" +#include "rt2800.h" #include "rt2800usb.h" /* @@ -44,1027 +46,6 @@ module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO); MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); /* - * Register access. - * All access to the CSR registers will go through the methods - * rt2x00usb_register_read and rt2x00usb_register_write. - * BBP and RF register require indirect register access, - * and use the CSR registers BBPCSR and RFCSR to achieve this. - * These indirect registers work with busy bits, - * and we will try maximal REGISTER_BUSY_COUNT times to access - * the register while taking a REGISTER_BUSY_DELAY us delay - * between each attampt. When the busy bit is still set at that time, - * the access attempt is considered to have failed, - * and we will print an error. - * The _lock versions must be used if you already hold the csr_mutex - */ -#define WAIT_FOR_BBP(__dev, __reg) \ - rt2x00usb_regbusy_read((__dev), BBP_CSR_CFG, BBP_CSR_CFG_BUSY, (__reg)) -#define WAIT_FOR_RFCSR(__dev, __reg) \ - rt2x00usb_regbusy_read((__dev), RF_CSR_CFG, RF_CSR_CFG_BUSY, (__reg)) -#define WAIT_FOR_RF(__dev, __reg) \ - rt2x00usb_regbusy_read((__dev), RF_CSR_CFG0, RF_CSR_CFG0_BUSY, (__reg)) -#define WAIT_FOR_MCU(__dev, __reg) \ - rt2x00usb_regbusy_read((__dev), H2M_MAILBOX_CSR, \ - H2M_MAILBOX_CSR_OWNER, (__reg)) - -static void rt2800usb_bbp_write(struct rt2x00_dev *rt2x00dev, - const unsigned int word, const u8 value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the BBP becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_BBP(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, BBP_CSR_CFG_VALUE, value); - rt2x00_set_field32(®, BBP_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, BBP_CSR_CFG_BUSY, 1); - rt2x00_set_field32(®, BBP_CSR_CFG_READ_CONTROL, 0); - - rt2x00usb_register_write_lock(rt2x00dev, BBP_CSR_CFG, reg); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800usb_bbp_read(struct rt2x00_dev *rt2x00dev, - const unsigned int word, u8 *value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the BBP becomes available, afterwards we - * can safely write the read request into the register. - * After the data has been written, we wait until hardware - * returns the correct value, if at any time the register - * doesn't become available in time, reg will be 0xffffffff - * which means we return 0xff to the caller. - */ - if (WAIT_FOR_BBP(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, BBP_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, BBP_CSR_CFG_BUSY, 1); - rt2x00_set_field32(®, BBP_CSR_CFG_READ_CONTROL, 1); - - rt2x00usb_register_write_lock(rt2x00dev, BBP_CSR_CFG, reg); - - WAIT_FOR_BBP(rt2x00dev, ®); - } - - *value = rt2x00_get_field32(reg, BBP_CSR_CFG_VALUE); - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800usb_rfcsr_write(struct rt2x00_dev *rt2x00dev, - const unsigned int word, const u8 value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the RFCSR becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_RFCSR(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, RF_CSR_CFG_DATA, value); - rt2x00_set_field32(®, RF_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, RF_CSR_CFG_WRITE, 1); - rt2x00_set_field32(®, RF_CSR_CFG_BUSY, 1); - - rt2x00usb_register_write_lock(rt2x00dev, RF_CSR_CFG, reg); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800usb_rfcsr_read(struct rt2x00_dev *rt2x00dev, - const unsigned int word, u8 *value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the RFCSR becomes available, afterwards we - * can safely write the read request into the register. - * After the data has been written, we wait until hardware - * returns the correct value, if at any time the register - * doesn't become available in time, reg will be 0xffffffff - * which means we return 0xff to the caller. - */ - if (WAIT_FOR_RFCSR(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, RF_CSR_CFG_REGNUM, word); - rt2x00_set_field32(®, RF_CSR_CFG_WRITE, 0); - rt2x00_set_field32(®, RF_CSR_CFG_BUSY, 1); - - rt2x00usb_register_write_lock(rt2x00dev, BBP_CSR_CFG, reg); - - WAIT_FOR_RFCSR(rt2x00dev, ®); - } - - *value = rt2x00_get_field32(reg, RF_CSR_CFG_DATA); - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800usb_rf_write(struct rt2x00_dev *rt2x00dev, - const unsigned int word, const u32 value) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the RF becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_RF(rt2x00dev, ®)) { - reg = 0; - rt2x00_set_field32(®, RF_CSR_CFG0_REG_VALUE_BW, value); - rt2x00_set_field32(®, RF_CSR_CFG0_STANDBYMODE, 0); - rt2x00_set_field32(®, RF_CSR_CFG0_SEL, 0); - rt2x00_set_field32(®, RF_CSR_CFG0_BUSY, 1); - - rt2x00usb_register_write_lock(rt2x00dev, RF_CSR_CFG0, reg); - rt2x00_rf_write(rt2x00dev, word, value); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -static void rt2800usb_mcu_request(struct rt2x00_dev *rt2x00dev, - const u8 command, const u8 token, - const u8 arg0, const u8 arg1) -{ - u32 reg; - - mutex_lock(&rt2x00dev->csr_mutex); - - /* - * Wait until the MCU becomes available, afterwards we - * can safely write the new data into the register. - */ - if (WAIT_FOR_MCU(rt2x00dev, ®)) { - rt2x00_set_field32(®, H2M_MAILBOX_CSR_OWNER, 1); - rt2x00_set_field32(®, H2M_MAILBOX_CSR_CMD_TOKEN, token); - rt2x00_set_field32(®, H2M_MAILBOX_CSR_ARG0, arg0); - rt2x00_set_field32(®, H2M_MAILBOX_CSR_ARG1, arg1); - rt2x00usb_register_write_lock(rt2x00dev, H2M_MAILBOX_CSR, reg); - - reg = 0; - rt2x00_set_field32(®, HOST_CMD_CSR_HOST_COMMAND, command); - rt2x00usb_register_write_lock(rt2x00dev, HOST_CMD_CSR, reg); - } - - mutex_unlock(&rt2x00dev->csr_mutex); -} - -#ifdef CONFIG_RT2X00_LIB_DEBUGFS -static const struct rt2x00debug rt2800usb_rt2x00debug = { - .owner = THIS_MODULE, - .csr = { - .read = rt2x00usb_register_read, - .write = rt2x00usb_register_write, - .flags = RT2X00DEBUGFS_OFFSET, - .word_base = CSR_REG_BASE, - .word_size = sizeof(u32), - .word_count = CSR_REG_SIZE / sizeof(u32), - }, - .eeprom = { - .read = rt2x00_eeprom_read, - .write = rt2x00_eeprom_write, - .word_base = EEPROM_BASE, - .word_size = sizeof(u16), - .word_count = EEPROM_SIZE / sizeof(u16), - }, - .bbp = { - .read = rt2800usb_bbp_read, - .write = rt2800usb_bbp_write, - .word_base = BBP_BASE, - .word_size = sizeof(u8), - .word_count = BBP_SIZE / sizeof(u8), - }, - .rf = { - .read = rt2x00_rf_read, - .write = rt2800usb_rf_write, - .word_base = RF_BASE, - .word_size = sizeof(u32), - .word_count = RF_SIZE / sizeof(u32), - }, -}; -#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ - -static int rt2800usb_rfkill_poll(struct rt2x00_dev *rt2x00dev) -{ - u32 reg; - - rt2x00usb_register_read(rt2x00dev, GPIO_CTRL_CFG, ®); - return rt2x00_get_field32(reg, GPIO_CTRL_CFG_BIT2); -} - -#ifdef CONFIG_RT2X00_LIB_LEDS -static void rt2800usb_brightness_set(struct led_classdev *led_cdev, - enum led_brightness brightness) -{ - struct rt2x00_led *led = - container_of(led_cdev, struct rt2x00_led, led_dev); - unsigned int enabled = brightness != LED_OFF; - unsigned int bg_mode = - (enabled && led->rt2x00dev->curr_band == IEEE80211_BAND_2GHZ); - unsigned int polarity = - rt2x00_get_field16(led->rt2x00dev->led_mcu_reg, - EEPROM_FREQ_LED_POLARITY); - unsigned int ledmode = - rt2x00_get_field16(led->rt2x00dev->led_mcu_reg, - EEPROM_FREQ_LED_MODE); - - if (led->type == LED_TYPE_RADIO) { - rt2800usb_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode, - enabled ? 0x20 : 0); - } else if (led->type == LED_TYPE_ASSOC) { - rt2800usb_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode, - enabled ? (bg_mode ? 0x60 : 0xa0) : 0x20); - } else if (led->type == LED_TYPE_QUALITY) { - /* - * The brightness is divided into 6 levels (0 - 5), - * The specs tell us the following levels: - * 0, 1 ,3, 7, 15, 31 - * to determine the level in a simple way we can simply - * work with bitshifting: - * (1 << level) - 1 - */ - rt2800usb_mcu_request(led->rt2x00dev, MCU_LED_STRENGTH, 0xff, - (1 << brightness / (LED_FULL / 6)) - 1, - polarity); - } -} - -static int rt2800usb_blink_set(struct led_classdev *led_cdev, - unsigned long *delay_on, - unsigned long *delay_off) -{ - struct rt2x00_led *led = - container_of(led_cdev, struct rt2x00_led, led_dev); - u32 reg; - - rt2x00usb_register_read(led->rt2x00dev, LED_CFG, ®); - rt2x00_set_field32(®, LED_CFG_ON_PERIOD, *delay_on); - rt2x00_set_field32(®, LED_CFG_OFF_PERIOD, *delay_off); - rt2x00_set_field32(®, LED_CFG_SLOW_BLINK_PERIOD, 3); - rt2x00_set_field32(®, LED_CFG_R_LED_MODE, 3); - rt2x00_set_field32(®, LED_CFG_G_LED_MODE, 12); - rt2x00_set_field32(®, LED_CFG_Y_LED_MODE, 3); - rt2x00_set_field32(®, LED_CFG_LED_POLAR, 1); - rt2x00usb_register_write(led->rt2x00dev, LED_CFG, reg); - - return 0; -} - -static void rt2800usb_init_led(struct rt2x00_dev *rt2x00dev, - struct rt2x00_led *led, - enum led_type type) -{ - led->rt2x00dev = rt2x00dev; - led->type = type; - led->led_dev.brightness_set = rt2800usb_brightness_set; - led->led_dev.blink_set = rt2800usb_blink_set; - led->flags = LED_INITIALIZED; -} -#endif /* CONFIG_RT2X00_LIB_LEDS */ - -/* - * Configuration handlers. - */ -static void rt2800usb_config_wcid_attr(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_crypto *crypto, - struct ieee80211_key_conf *key) -{ - struct mac_wcid_entry wcid_entry; - struct mac_iveiv_entry iveiv_entry; - u32 offset; - u32 reg; - - offset = MAC_WCID_ATTR_ENTRY(key->hw_key_idx); - - rt2x00usb_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_KEYTAB, - !!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_CIPHER, - (crypto->cmd == SET_KEY) * crypto->cipher); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_BSS_IDX, - (crypto->cmd == SET_KEY) * crypto->bssidx); - rt2x00_set_field32(®, MAC_WCID_ATTRIBUTE_RX_WIUDF, crypto->cipher); - rt2x00usb_register_write(rt2x00dev, offset, reg); - - offset = MAC_IVEIV_ENTRY(key->hw_key_idx); - - memset(&iveiv_entry, 0, sizeof(iveiv_entry)); - if ((crypto->cipher == CIPHER_TKIP) || - (crypto->cipher == CIPHER_TKIP_NO_MIC) || - (crypto->cipher == CIPHER_AES)) - iveiv_entry.iv[3] |= 0x20; - iveiv_entry.iv[3] |= key->keyidx << 6; - rt2x00usb_register_multiwrite(rt2x00dev, offset, - &iveiv_entry, sizeof(iveiv_entry)); - - offset = MAC_WCID_ENTRY(key->hw_key_idx); - - memset(&wcid_entry, 0, sizeof(wcid_entry)); - if (crypto->cmd == SET_KEY) - memcpy(&wcid_entry, crypto->address, ETH_ALEN); - rt2x00usb_register_multiwrite(rt2x00dev, offset, - &wcid_entry, sizeof(wcid_entry)); -} - -static int rt2800usb_config_shared_key(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_crypto *crypto, - struct ieee80211_key_conf *key) -{ - struct hw_key_entry key_entry; - struct rt2x00_field32 field; - int timeout; - u32 offset; - u32 reg; - - if (crypto->cmd == SET_KEY) { - key->hw_key_idx = (4 * crypto->bssidx) + key->keyidx; - - memcpy(key_entry.key, crypto->key, - sizeof(key_entry.key)); - memcpy(key_entry.tx_mic, crypto->tx_mic, - sizeof(key_entry.tx_mic)); - memcpy(key_entry.rx_mic, crypto->rx_mic, - sizeof(key_entry.rx_mic)); - - offset = SHARED_KEY_ENTRY(key->hw_key_idx); - timeout = REGISTER_TIMEOUT32(sizeof(key_entry)); - rt2x00usb_vendor_request_large_buff(rt2x00dev, USB_MULTI_WRITE, - USB_VENDOR_REQUEST_OUT, - offset, &key_entry, - sizeof(key_entry), - timeout); - } - - /* - * The cipher types are stored over multiple registers - * starting with SHARED_KEY_MODE_BASE each word will have - * 32 bits and contains the cipher types for 2 bssidx each. - * Using the correct defines correctly will cause overhead, - * so just calculate the correct offset. - */ - field.bit_offset = 4 * (key->hw_key_idx % 8); - field.bit_mask = 0x7 << field.bit_offset; - - offset = SHARED_KEY_MODE_ENTRY(key->hw_key_idx / 8); - - rt2x00usb_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, field, - (crypto->cmd == SET_KEY) * crypto->cipher); - rt2x00usb_register_write(rt2x00dev, offset, reg); - - /* - * Update WCID information - */ - rt2800usb_config_wcid_attr(rt2x00dev, crypto, key); - - return 0; -} - -static int rt2800usb_config_pairwise_key(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_crypto *crypto, - struct ieee80211_key_conf *key) -{ - struct hw_key_entry key_entry; - int timeout; - u32 offset; - - if (crypto->cmd == SET_KEY) { - /* - * 1 pairwise key is possible per AID, this means that the AID - * equals our hw_key_idx. Make sure the WCID starts _after_ the - * last possible shared key entry. - */ - if (crypto->aid > (256 - 32)) - return -ENOSPC; - - key->hw_key_idx = 32 + crypto->aid; - - memcpy(key_entry.key, crypto->key, - sizeof(key_entry.key)); - memcpy(key_entry.tx_mic, crypto->tx_mic, - sizeof(key_entry.tx_mic)); - memcpy(key_entry.rx_mic, crypto->rx_mic, - sizeof(key_entry.rx_mic)); - - offset = PAIRWISE_KEY_ENTRY(key->hw_key_idx); - timeout = REGISTER_TIMEOUT32(sizeof(key_entry)); - rt2x00usb_vendor_request_large_buff(rt2x00dev, USB_MULTI_WRITE, - USB_VENDOR_REQUEST_OUT, - offset, &key_entry, - sizeof(key_entry), - timeout); - } - - /* - * Update WCID information - */ - rt2800usb_config_wcid_attr(rt2x00dev, crypto, key); - - return 0; -} - -static void rt2800usb_config_filter(struct rt2x00_dev *rt2x00dev, - const unsigned int filter_flags) -{ - u32 reg; - - /* - * Start configuration steps. - * Note that the version error will always be dropped - * and broadcast frames will always be accepted since - * there is no filter for it at this time. - */ - rt2x00usb_register_read(rt2x00dev, RX_FILTER_CFG, ®); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CRC_ERROR, - !(filter_flags & FIF_FCSFAIL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PHY_ERROR, - !(filter_flags & FIF_PLCPFAIL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_NOT_TO_ME, - !(filter_flags & FIF_PROMISC_IN_BSS)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_NOT_MY_BSSD, 0); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_VER_ERROR, 1); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_MULTICAST, - !(filter_flags & FIF_ALLMULTI)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BROADCAST, 0); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_DUPLICATE, 1); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CF_END_ACK, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CF_END, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_ACK, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CTS, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_RTS, - !(filter_flags & FIF_CONTROL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PSPOLL, - !(filter_flags & FIF_PSPOLL)); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BA, 1); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BAR, 0); - rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CNTL, - !(filter_flags & FIF_CONTROL)); - rt2x00usb_register_write(rt2x00dev, RX_FILTER_CFG, reg); -} - -static void rt2800usb_config_intf(struct rt2x00_dev *rt2x00dev, - struct rt2x00_intf *intf, - struct rt2x00intf_conf *conf, - const unsigned int flags) -{ - unsigned int beacon_base; - u32 reg; - - if (flags & CONFIG_UPDATE_TYPE) { - /* - * Clear current synchronisation setup. - * For the Beacon base registers we only need to clear - * the first byte since that byte contains the VALID and OWNER - * bits which (when set to 0) will invalidate the entire beacon. - */ - beacon_base = HW_BEACON_OFFSET(intf->beacon->entry_idx); - rt2x00usb_register_write(rt2x00dev, beacon_base, 0); - - /* - * Enable synchronisation. - */ - rt2x00usb_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_SYNC, conf->sync); - rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1); - rt2x00usb_register_write(rt2x00dev, BCN_TIME_CFG, reg); - } - - if (flags & CONFIG_UPDATE_MAC) { - reg = le32_to_cpu(conf->mac[1]); - rt2x00_set_field32(®, MAC_ADDR_DW1_UNICAST_TO_ME_MASK, 0xff); - conf->mac[1] = cpu_to_le32(reg); - - rt2x00usb_register_multiwrite(rt2x00dev, MAC_ADDR_DW0, - conf->mac, sizeof(conf->mac)); - } - - if (flags & CONFIG_UPDATE_BSSID) { - reg = le32_to_cpu(conf->bssid[1]); - rt2x00_set_field32(®, MAC_BSSID_DW1_BSS_ID_MASK, 0); - rt2x00_set_field32(®, MAC_BSSID_DW1_BSS_BCN_NUM, 0); - conf->bssid[1] = cpu_to_le32(reg); - - rt2x00usb_register_multiwrite(rt2x00dev, MAC_BSSID_DW0, - conf->bssid, sizeof(conf->bssid)); - } -} - -static void rt2800usb_config_erp(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_erp *erp) -{ - u32 reg; - - rt2x00usb_register_read(rt2x00dev, TX_TIMEOUT_CFG, ®); - rt2x00_set_field32(®, TX_TIMEOUT_CFG_RX_ACK_TIMEOUT, 0x20); - rt2x00usb_register_write(rt2x00dev, TX_TIMEOUT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, AUTO_RSP_CFG, ®); - rt2x00_set_field32(®, AUTO_RSP_CFG_BAC_ACK_POLICY, - !!erp->short_preamble); - rt2x00_set_field32(®, AUTO_RSP_CFG_AR_PREAMBLE, - !!erp->short_preamble); - rt2x00usb_register_write(rt2x00dev, AUTO_RSP_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, OFDM_PROT_CFG, ®); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, - erp->cts_protection ? 2 : 0); - rt2x00usb_register_write(rt2x00dev, OFDM_PROT_CFG, reg); - - rt2x00usb_register_write(rt2x00dev, LEGACY_BASIC_RATE, - erp->basic_rates); - rt2x00usb_register_write(rt2x00dev, HT_BASIC_RATE, 0x00008003); - - rt2x00usb_register_read(rt2x00dev, BKOFF_SLOT_CFG, ®); - rt2x00_set_field32(®, BKOFF_SLOT_CFG_SLOT_TIME, erp->slot_time); - rt2x00_set_field32(®, BKOFF_SLOT_CFG_CC_DELAY_TIME, 2); - rt2x00usb_register_write(rt2x00dev, BKOFF_SLOT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, XIFS_TIME_CFG, ®); - rt2x00_set_field32(®, XIFS_TIME_CFG_CCKM_SIFS_TIME, erp->sifs); - rt2x00_set_field32(®, XIFS_TIME_CFG_OFDM_SIFS_TIME, erp->sifs); - rt2x00_set_field32(®, XIFS_TIME_CFG_OFDM_XIFS_TIME, 4); - rt2x00_set_field32(®, XIFS_TIME_CFG_EIFS, erp->eifs); - rt2x00_set_field32(®, XIFS_TIME_CFG_BB_RXEND_ENABLE, 1); - rt2x00usb_register_write(rt2x00dev, XIFS_TIME_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_INTERVAL, - erp->beacon_int * 16); - rt2x00usb_register_write(rt2x00dev, BCN_TIME_CFG, reg); -} - -static void rt2800usb_config_ant(struct rt2x00_dev *rt2x00dev, - struct antenna_setup *ant) -{ - u8 r1; - u8 r3; - - rt2800usb_bbp_read(rt2x00dev, 1, &r1); - rt2800usb_bbp_read(rt2x00dev, 3, &r3); - - /* - * Configure the TX antenna. - */ - switch ((int)ant->tx) { - case 1: - rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 0); - break; - case 2: - rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 2); - break; - case 3: - /* Do nothing */ - break; - } - - /* - * Configure the RX antenna. - */ - switch ((int)ant->rx) { - case 1: - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 0); - break; - case 2: - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 1); - break; - case 3: - rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 2); - break; - } - - rt2800usb_bbp_write(rt2x00dev, 3, r3); - rt2800usb_bbp_write(rt2x00dev, 1, r1); -} - -static void rt2800usb_config_lna_gain(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf) -{ - u16 eeprom; - short lna_gain; - - if (libconf->rf.channel <= 14) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_LNA, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_LNA_BG); - } else if (libconf->rf.channel <= 64) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_LNA, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_LNA_A0); - } else if (libconf->rf.channel <= 128) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_BG2, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_RSSI_BG2_LNA_A1); - } else { - rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_A2, &eeprom); - lna_gain = rt2x00_get_field16(eeprom, EEPROM_RSSI_A2_LNA_A2); - } - - rt2x00dev->lna_gain = lna_gain; -} - -static void rt2800usb_config_channel_rt2x(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf, - struct rf_channel *rf, - struct channel_info *info) -{ - rt2x00_set_field32(&rf->rf4, RF4_FREQ_OFFSET, rt2x00dev->freq_offset); - - if (rt2x00dev->default_ant.tx == 1) - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_TX1, 1); - - if (rt2x00dev->default_ant.rx == 1) { - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX1, 1); - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1); - } else if (rt2x00dev->default_ant.rx == 2) - rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1); - - if (rf->channel > 14) { - /* - * When TX power is below 0, we should increase it by 7 to - * make it a positive value (Minumum value is -7). - * However this means that values between 0 and 7 have - * double meaning, and we should set a 7DBm boost flag. - */ - rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_A_7DBM_BOOST, - (info->tx_power1 >= 0)); - - if (info->tx_power1 < 0) - info->tx_power1 += 7; - - rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_A, - TXPOWER_A_TO_DEV(info->tx_power1)); - - rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_A_7DBM_BOOST, - (info->tx_power2 >= 0)); - - if (info->tx_power2 < 0) - info->tx_power2 += 7; - - rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_A, - TXPOWER_A_TO_DEV(info->tx_power2)); - } else { - rt2x00_set_field32(&rf->rf3, RF3_TXPOWER_G, - TXPOWER_G_TO_DEV(info->tx_power1)); - rt2x00_set_field32(&rf->rf4, RF4_TXPOWER_G, - TXPOWER_G_TO_DEV(info->tx_power2)); - } - - rt2x00_set_field32(&rf->rf4, RF4_HT40, conf_is_ht40(conf)); - - rt2800usb_rf_write(rt2x00dev, 1, rf->rf1); - rt2800usb_rf_write(rt2x00dev, 2, rf->rf2); - rt2800usb_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); - rt2800usb_rf_write(rt2x00dev, 4, rf->rf4); - - udelay(200); - - rt2800usb_rf_write(rt2x00dev, 1, rf->rf1); - rt2800usb_rf_write(rt2x00dev, 2, rf->rf2); - rt2800usb_rf_write(rt2x00dev, 3, rf->rf3 | 0x00000004); - rt2800usb_rf_write(rt2x00dev, 4, rf->rf4); - - udelay(200); - - rt2800usb_rf_write(rt2x00dev, 1, rf->rf1); - rt2800usb_rf_write(rt2x00dev, 2, rf->rf2); - rt2800usb_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); - rt2800usb_rf_write(rt2x00dev, 4, rf->rf4); -} - -static void rt2800usb_config_channel_rt3x(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf, - struct rf_channel *rf, - struct channel_info *info) -{ - u8 rfcsr; - - rt2800usb_rfcsr_write(rt2x00dev, 2, rf->rf1); - rt2800usb_rfcsr_write(rt2x00dev, 2, rf->rf3); - - rt2800usb_rfcsr_read(rt2x00dev, 6, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR6_R, rf->rf2); - rt2800usb_rfcsr_write(rt2x00dev, 6, rfcsr); - - rt2800usb_rfcsr_read(rt2x00dev, 12, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR12_TX_POWER, - TXPOWER_G_TO_DEV(info->tx_power1)); - rt2800usb_rfcsr_write(rt2x00dev, 12, rfcsr); - - rt2800usb_rfcsr_read(rt2x00dev, 23, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR23_FREQ_OFFSET, rt2x00dev->freq_offset); - rt2800usb_rfcsr_write(rt2x00dev, 23, rfcsr); - - rt2800usb_rfcsr_write(rt2x00dev, 24, - rt2x00dev->calibration[conf_is_ht40(conf)]); - - rt2800usb_rfcsr_read(rt2x00dev, 23, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR7_RF_TUNING, 1); - rt2800usb_rfcsr_write(rt2x00dev, 23, rfcsr); -} - -static void rt2800usb_config_channel(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf, - struct rf_channel *rf, - struct channel_info *info) -{ - u32 reg; - unsigned int tx_pin; - u8 bbp; - - if (rt2x00_rev(&rt2x00dev->chip) != RT3070_VERSION) - rt2800usb_config_channel_rt2x(rt2x00dev, conf, rf, info); - else - rt2800usb_config_channel_rt3x(rt2x00dev, conf, rf, info); - - /* - * Change BBP settings - */ - rt2800usb_bbp_write(rt2x00dev, 62, 0x37 - rt2x00dev->lna_gain); - rt2800usb_bbp_write(rt2x00dev, 63, 0x37 - rt2x00dev->lna_gain); - rt2800usb_bbp_write(rt2x00dev, 64, 0x37 - rt2x00dev->lna_gain); - rt2800usb_bbp_write(rt2x00dev, 86, 0); - - if (rf->channel <= 14) { - if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags)) { - rt2800usb_bbp_write(rt2x00dev, 82, 0x62); - rt2800usb_bbp_write(rt2x00dev, 75, 0x46); - } else { - rt2800usb_bbp_write(rt2x00dev, 82, 0x84); - rt2800usb_bbp_write(rt2x00dev, 75, 0x50); - } - } else { - rt2800usb_bbp_write(rt2x00dev, 82, 0xf2); - - if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags)) - rt2800usb_bbp_write(rt2x00dev, 75, 0x46); - else - rt2800usb_bbp_write(rt2x00dev, 75, 0x50); - } - - rt2x00usb_register_read(rt2x00dev, TX_BAND_CFG, ®); - rt2x00_set_field32(®, TX_BAND_CFG_HT40_PLUS, conf_is_ht40_plus(conf)); - rt2x00_set_field32(®, TX_BAND_CFG_A, rf->channel > 14); - rt2x00_set_field32(®, TX_BAND_CFG_BG, rf->channel <= 14); - rt2x00usb_register_write(rt2x00dev, TX_BAND_CFG, reg); - - tx_pin = 0; - - /* Turn on unused PA or LNA when not using 1T or 1R */ - if (rt2x00dev->default_ant.tx != 1) { - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A1_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G1_EN, 1); - } - - /* Turn on unused PA or LNA when not using 1T or 1R */ - if (rt2x00dev->default_ant.rx != 1) { - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A1_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G1_EN, 1); - } - - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A0_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G0_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_RFTR_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_TRSW_EN, 1); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G0_EN, rf->channel <= 14); - rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A0_EN, rf->channel > 14); - - rt2x00usb_register_write(rt2x00dev, TX_PIN_CFG, tx_pin); - - rt2800usb_bbp_read(rt2x00dev, 4, &bbp); - rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * conf_is_ht40(conf)); - rt2800usb_bbp_write(rt2x00dev, 4, bbp); - - rt2800usb_bbp_read(rt2x00dev, 3, &bbp); - rt2x00_set_field8(&bbp, BBP3_HT40_PLUS, conf_is_ht40_plus(conf)); - rt2800usb_bbp_write(rt2x00dev, 3, bbp); - - if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) { - if (conf_is_ht40(conf)) { - rt2800usb_bbp_write(rt2x00dev, 69, 0x1a); - rt2800usb_bbp_write(rt2x00dev, 70, 0x0a); - rt2800usb_bbp_write(rt2x00dev, 73, 0x16); - } else { - rt2800usb_bbp_write(rt2x00dev, 69, 0x16); - rt2800usb_bbp_write(rt2x00dev, 70, 0x08); - rt2800usb_bbp_write(rt2x00dev, 73, 0x11); - } - } - - msleep(1); -} - -static void rt2800usb_config_txpower(struct rt2x00_dev *rt2x00dev, - const int txpower) -{ - u32 reg; - u32 value = TXPOWER_G_TO_DEV(txpower); - u8 r1; - - rt2800usb_bbp_read(rt2x00dev, 1, &r1); - rt2x00_set_field8(®, BBP1_TX_POWER, 0); - rt2800usb_bbp_write(rt2x00dev, 1, r1); - - rt2x00usb_register_read(rt2x00dev, TX_PWR_CFG_0, ®); - rt2x00_set_field32(®, TX_PWR_CFG_0_1MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_2MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_55MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_11MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_6MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_9MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_12MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_0_18MBS, value); - rt2x00usb_register_write(rt2x00dev, TX_PWR_CFG_0, reg); - - rt2x00usb_register_read(rt2x00dev, TX_PWR_CFG_1, ®); - rt2x00_set_field32(®, TX_PWR_CFG_1_24MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_36MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_48MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_54MBS, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS0, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS1, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS2, value); - rt2x00_set_field32(®, TX_PWR_CFG_1_MCS3, value); - rt2x00usb_register_write(rt2x00dev, TX_PWR_CFG_1, reg); - - rt2x00usb_register_read(rt2x00dev, TX_PWR_CFG_2, ®); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS4, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS5, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS6, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS7, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS8, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS9, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS10, value); - rt2x00_set_field32(®, TX_PWR_CFG_2_MCS11, value); - rt2x00usb_register_write(rt2x00dev, TX_PWR_CFG_2, reg); - - rt2x00usb_register_read(rt2x00dev, TX_PWR_CFG_3, ®); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS12, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS13, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS14, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_MCS15, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN1, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN2, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN3, value); - rt2x00_set_field32(®, TX_PWR_CFG_3_UKNOWN4, value); - rt2x00usb_register_write(rt2x00dev, TX_PWR_CFG_3, reg); - - rt2x00usb_register_read(rt2x00dev, TX_PWR_CFG_4, ®); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN5, value); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN6, value); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN7, value); - rt2x00_set_field32(®, TX_PWR_CFG_4_UKNOWN8, value); - rt2x00usb_register_write(rt2x00dev, TX_PWR_CFG_4, reg); -} - -static void rt2800usb_config_retry_limit(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf) -{ - u32 reg; - - rt2x00usb_register_read(rt2x00dev, TX_RTY_CFG, ®); - rt2x00_set_field32(®, TX_RTY_CFG_SHORT_RTY_LIMIT, - libconf->conf->short_frame_max_tx_count); - rt2x00_set_field32(®, TX_RTY_CFG_LONG_RTY_LIMIT, - libconf->conf->long_frame_max_tx_count); - rt2x00_set_field32(®, TX_RTY_CFG_LONG_RTY_THRE, 2000); - rt2x00_set_field32(®, TX_RTY_CFG_NON_AGG_RTY_MODE, 0); - rt2x00_set_field32(®, TX_RTY_CFG_AGG_RTY_MODE, 0); - rt2x00_set_field32(®, TX_RTY_CFG_TX_AUTO_FB_ENABLE, 1); - rt2x00usb_register_write(rt2x00dev, TX_RTY_CFG, reg); -} - -static void rt2800usb_config_ps(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf) -{ - enum dev_state state = - (libconf->conf->flags & IEEE80211_CONF_PS) ? - STATE_SLEEP : STATE_AWAKE; - u32 reg; - - if (state == STATE_SLEEP) { - rt2x00usb_register_write(rt2x00dev, AUTOWAKEUP_CFG, 0); - - rt2x00usb_register_read(rt2x00dev, AUTOWAKEUP_CFG, ®); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTO_LEAD_TIME, 5); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE, - libconf->conf->listen_interval - 1); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTOWAKE, 1); - rt2x00usb_register_write(rt2x00dev, AUTOWAKEUP_CFG, reg); - - rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); - } else { - rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); - - rt2x00usb_register_read(rt2x00dev, AUTOWAKEUP_CFG, ®); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTO_LEAD_TIME, 0); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE, 0); - rt2x00_set_field32(®, AUTOWAKEUP_CFG_AUTOWAKE, 0); - rt2x00usb_register_write(rt2x00dev, AUTOWAKEUP_CFG, reg); - } -} - -static void rt2800usb_config(struct rt2x00_dev *rt2x00dev, - struct rt2x00lib_conf *libconf, - const unsigned int flags) -{ - /* Always recalculate LNA gain before changing configuration */ - rt2800usb_config_lna_gain(rt2x00dev, libconf); - - if (flags & IEEE80211_CONF_CHANGE_CHANNEL) - rt2800usb_config_channel(rt2x00dev, libconf->conf, - &libconf->rf, &libconf->channel); - if (flags & IEEE80211_CONF_CHANGE_POWER) - rt2800usb_config_txpower(rt2x00dev, libconf->conf->power_level); - if (flags & IEEE80211_CONF_CHANGE_RETRY_LIMITS) - rt2800usb_config_retry_limit(rt2x00dev, libconf); - if (flags & IEEE80211_CONF_CHANGE_PS) - rt2800usb_config_ps(rt2x00dev, libconf); -} - -/* - * Link tuning - */ -static void rt2800usb_link_stats(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual) -{ - u32 reg; - - /* - * Update FCS error count from register. - */ - rt2x00usb_register_read(rt2x00dev, RX_STA_CNT0, ®); - qual->rx_failed = rt2x00_get_field32(reg, RX_STA_CNT0_CRC_ERR); -} - -static u8 rt2800usb_get_default_vgc(struct rt2x00_dev *rt2x00dev) -{ - if (rt2x00dev->curr_band == IEEE80211_BAND_2GHZ) { - if (rt2x00_rev(&rt2x00dev->chip) == RT3070_VERSION) - return 0x1c + (2 * rt2x00dev->lna_gain); - else - return 0x2e + rt2x00dev->lna_gain; - } - - if (!test_bit(CONFIG_CHANNEL_HT40, &rt2x00dev->flags)) - return 0x32 + (rt2x00dev->lna_gain * 5) / 3; - else - return 0x3a + (rt2x00dev->lna_gain * 5) / 3; -} - -static inline void rt2800usb_set_vgc(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual, u8 vgc_level) -{ - if (qual->vgc_level != vgc_level) { - rt2800usb_bbp_write(rt2x00dev, 66, vgc_level); - qual->vgc_level = vgc_level; - qual->vgc_level_reg = vgc_level; - } -} - -static void rt2800usb_reset_tuner(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual) -{ - rt2800usb_set_vgc(rt2x00dev, qual, - rt2800usb_get_default_vgc(rt2x00dev)); -} - -static void rt2800usb_link_tuner(struct rt2x00_dev *rt2x00dev, - struct link_qual *qual, const u32 count) -{ - if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) - return; - - /* - * When RSSI is better then -80 increase VGC level with 0x10 - */ - rt2800usb_set_vgc(rt2x00dev, qual, - rt2800usb_get_default_vgc(rt2x00dev) + - ((qual->rssi > -80) * 0x10)); -} - -/* * Firmware functions */ static char *rt2800usb_get_firmware_name(struct rt2x00_dev *rt2x00dev) @@ -1172,7 +153,7 @@ static int rt2800usb_load_firmware(struct rt2x00_dev *rt2x00dev, * Wait for stable hardware. */ for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00usb_register_read(rt2x00dev, MAC_CSR0, ®); + rt2800_register_read(rt2x00dev, MAC_CSR0, ®); if (reg && reg != ~0) break; msleep(1); @@ -1192,8 +173,8 @@ static int rt2800usb_load_firmware(struct rt2x00_dev *rt2x00dev, data + offset, length, REGISTER_TIMEOUT32(length)); - rt2x00usb_register_write(rt2x00dev, H2M_MAILBOX_CID, ~0); - rt2x00usb_register_write(rt2x00dev, H2M_MAILBOX_STATUS, ~0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_CID, ~0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_STATUS, ~0); /* * Send firmware request to device to load firmware, @@ -1208,18 +189,18 @@ static int rt2800usb_load_firmware(struct rt2x00_dev *rt2x00dev, } msleep(10); - rt2x00usb_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); /* * Send signal to firmware during boot time. */ - rt2800usb_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0); + rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0); if ((chipset == 0x3070) || (chipset == 0x3071) || (chipset == 0x3572)) { udelay(200); - rt2800usb_mcu_request(rt2x00dev, MCU_CURRENT, 0, 0, 0); + rt2800_mcu_request(rt2x00dev, MCU_CURRENT, 0, 0, 0); udelay(10); } @@ -1227,7 +208,7 @@ static int rt2800usb_load_firmware(struct rt2x00_dev *rt2x00dev, * Wait for device to stabilize. */ for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00usb_register_read(rt2x00dev, PBF_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, PBF_SYS_CTRL, ®); if (rt2x00_get_field32(reg, PBF_SYS_CTRL_READY)) break; msleep(1); @@ -1241,536 +222,14 @@ static int rt2800usb_load_firmware(struct rt2x00_dev *rt2x00dev, /* * Initialize firmware. */ - rt2x00usb_register_write(rt2x00dev, H2M_BBP_AGENT, 0); - rt2x00usb_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); + rt2800_register_write(rt2x00dev, H2M_BBP_AGENT, 0); + rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); msleep(1); return 0; } /* - * Initialization functions. - */ -static int rt2800usb_init_registers(struct rt2x00_dev *rt2x00dev) -{ - u32 reg; - unsigned int i; - - /* - * Wait untill BBP and RF are ready. - */ - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00usb_register_read(rt2x00dev, MAC_CSR0, ®); - if (reg && reg != ~0) - break; - msleep(1); - } - - if (i == REGISTER_BUSY_COUNT) { - ERROR(rt2x00dev, "Unstable hardware.\n"); - return -EBUSY; - } - - rt2x00usb_register_read(rt2x00dev, PBF_SYS_CTRL, ®); - rt2x00usb_register_write(rt2x00dev, PBF_SYS_CTRL, reg & ~0x00002000); - - rt2x00usb_register_read(rt2x00dev, MAC_SYS_CTRL, ®); - rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_CSR, 1); - rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_BBP, 1); - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, reg); - - rt2x00usb_register_write(rt2x00dev, USB_DMA_CFG, 0x00000000); - - rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0, - USB_MODE_RESET, REGISTER_TIMEOUT); - - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); - - rt2x00usb_register_read(rt2x00dev, BCN_OFFSET0, ®); - rt2x00_set_field32(®, BCN_OFFSET0_BCN0, 0xe0); /* 0x3800 */ - rt2x00_set_field32(®, BCN_OFFSET0_BCN1, 0xe8); /* 0x3a00 */ - rt2x00_set_field32(®, BCN_OFFSET0_BCN2, 0xf0); /* 0x3c00 */ - rt2x00_set_field32(®, BCN_OFFSET0_BCN3, 0xf8); /* 0x3e00 */ - rt2x00usb_register_write(rt2x00dev, BCN_OFFSET0, reg); - - rt2x00usb_register_read(rt2x00dev, BCN_OFFSET1, ®); - rt2x00_set_field32(®, BCN_OFFSET1_BCN4, 0xc8); /* 0x3200 */ - rt2x00_set_field32(®, BCN_OFFSET1_BCN5, 0xd0); /* 0x3400 */ - rt2x00_set_field32(®, BCN_OFFSET1_BCN6, 0x77); /* 0x1dc0 */ - rt2x00_set_field32(®, BCN_OFFSET1_BCN7, 0x6f); /* 0x1bc0 */ - rt2x00usb_register_write(rt2x00dev, BCN_OFFSET1, reg); - - rt2x00usb_register_write(rt2x00dev, LEGACY_BASIC_RATE, 0x0000013f); - rt2x00usb_register_write(rt2x00dev, HT_BASIC_RATE, 0x00008003); - - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); - - rt2x00usb_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_INTERVAL, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_SYNC, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0); - rt2x00_set_field32(®, BCN_TIME_CFG_TX_TIME_COMPENSATE, 0); - rt2x00usb_register_write(rt2x00dev, BCN_TIME_CFG, reg); - - if (rt2x00_rev(&rt2x00dev->chip) == RT3070_VERSION) { - rt2x00usb_register_write(rt2x00dev, TX_SW_CFG0, 0x00000400); - rt2x00usb_register_write(rt2x00dev, TX_SW_CFG1, 0x00000000); - rt2x00usb_register_write(rt2x00dev, TX_SW_CFG2, 0x00000000); - } else { - rt2x00usb_register_write(rt2x00dev, TX_SW_CFG0, 0x00000000); - rt2x00usb_register_write(rt2x00dev, TX_SW_CFG1, 0x00080606); - } - - rt2x00usb_register_read(rt2x00dev, TX_LINK_CFG, ®); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFB_LIFETIME, 32); - rt2x00_set_field32(®, TX_LINK_CFG_MFB_ENABLE, 0); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_UMFS_ENABLE, 0); - rt2x00_set_field32(®, TX_LINK_CFG_TX_MRQ_EN, 0); - rt2x00_set_field32(®, TX_LINK_CFG_TX_RDG_EN, 0); - rt2x00_set_field32(®, TX_LINK_CFG_TX_CF_ACK_EN, 1); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFB, 0); - rt2x00_set_field32(®, TX_LINK_CFG_REMOTE_MFS, 0); - rt2x00usb_register_write(rt2x00dev, TX_LINK_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, TX_TIMEOUT_CFG, ®); - rt2x00_set_field32(®, TX_TIMEOUT_CFG_MPDU_LIFETIME, 9); - rt2x00_set_field32(®, TX_TIMEOUT_CFG_TX_OP_TIMEOUT, 10); - rt2x00usb_register_write(rt2x00dev, TX_TIMEOUT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, MAX_LEN_CFG, ®); - rt2x00_set_field32(®, MAX_LEN_CFG_MAX_MPDU, AGGREGATION_SIZE); - if (rt2x00_rev(&rt2x00dev->chip) >= RT2880E_VERSION && - rt2x00_rev(&rt2x00dev->chip) < RT3070_VERSION) - rt2x00_set_field32(®, MAX_LEN_CFG_MAX_PSDU, 2); - else - rt2x00_set_field32(®, MAX_LEN_CFG_MAX_PSDU, 1); - rt2x00_set_field32(®, MAX_LEN_CFG_MIN_PSDU, 0); - rt2x00_set_field32(®, MAX_LEN_CFG_MIN_MPDU, 0); - rt2x00usb_register_write(rt2x00dev, MAX_LEN_CFG, reg); - - rt2x00usb_register_write(rt2x00dev, PBF_MAX_PCNT, 0x1f3fbf9f); - - rt2x00usb_register_read(rt2x00dev, AUTO_RSP_CFG, ®); - rt2x00_set_field32(®, AUTO_RSP_CFG_AUTORESPONDER, 1); - rt2x00_set_field32(®, AUTO_RSP_CFG_CTS_40_MMODE, 0); - rt2x00_set_field32(®, AUTO_RSP_CFG_CTS_40_MREF, 0); - rt2x00_set_field32(®, AUTO_RSP_CFG_DUAL_CTS_EN, 0); - rt2x00_set_field32(®, AUTO_RSP_CFG_ACK_CTS_PSM_BIT, 0); - rt2x00usb_register_write(rt2x00dev, AUTO_RSP_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, CCK_PROT_CFG, ®); - rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_RATE, 8); - rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00usb_register_write(rt2x00dev, CCK_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, OFDM_PROT_CFG, ®); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_RATE, 8); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00usb_register_write(rt2x00dev, OFDM_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, MM20_PROT_CFG, ®); - rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_RATE, 0x4004); - rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM40, 0); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_GF40, 0); - rt2x00usb_register_write(rt2x00dev, MM20_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, MM40_PROT_CFG, ®); - rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_RATE, 0x4084); - rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00usb_register_write(rt2x00dev, MM40_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, GF20_PROT_CFG, ®); - rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_RATE, 0x4004); - rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM40, 0); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_GF40, 0); - rt2x00usb_register_write(rt2x00dev, GF20_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, GF40_PROT_CFG, ®); - rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_RATE, 0x4084); - rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_CTRL, 0); - rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_NAV, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_CCK, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_OFDM, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM20, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM40, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_GF20, 1); - rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_GF40, 1); - rt2x00usb_register_write(rt2x00dev, GF40_PROT_CFG, reg); - - rt2x00usb_register_write(rt2x00dev, PBF_CFG, 0xf40006); - - rt2x00usb_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); - rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_DMA_BUSY, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_DMA_BUSY, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_WP_DMA_BURST_SIZE, 3); - rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_BIG_ENDIAN, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_HDR_SCATTER, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_HDR_SEG_LEN, 0); - rt2x00usb_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - - rt2x00usb_register_write(rt2x00dev, TXOP_CTRL_CFG, 0x0000583f); - rt2x00usb_register_write(rt2x00dev, TXOP_HLDR_ET, 0x00000002); - - rt2x00usb_register_read(rt2x00dev, TX_RTS_CFG, ®); - rt2x00_set_field32(®, TX_RTS_CFG_AUTO_RTS_RETRY_LIMIT, 32); - rt2x00_set_field32(®, TX_RTS_CFG_RTS_THRES, - IEEE80211_MAX_RTS_THRESHOLD); - rt2x00_set_field32(®, TX_RTS_CFG_RTS_FBK_EN, 0); - rt2x00usb_register_write(rt2x00dev, TX_RTS_CFG, reg); - - rt2x00usb_register_write(rt2x00dev, EXP_ACK_TIME, 0x002400ca); - rt2x00usb_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003); - - /* - * ASIC will keep garbage value after boot, clear encryption keys. - */ - for (i = 0; i < 4; i++) - rt2x00usb_register_write(rt2x00dev, - SHARED_KEY_MODE_ENTRY(i), 0); - - for (i = 0; i < 256; i++) { - u32 wcid[2] = { 0xffffffff, 0x00ffffff }; - rt2x00usb_register_multiwrite(rt2x00dev, MAC_WCID_ENTRY(i), - wcid, sizeof(wcid)); - - rt2x00usb_register_write(rt2x00dev, MAC_WCID_ATTR_ENTRY(i), 1); - rt2x00usb_register_write(rt2x00dev, MAC_IVEIV_ENTRY(i), 0); - } - - /* - * Clear all beacons - * For the Beacon base registers we only need to clear - * the first byte since that byte contains the VALID and OWNER - * bits which (when set to 0) will invalidate the entire beacon. - */ - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE0, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE1, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE2, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE3, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE4, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE5, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE6, 0); - rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE7, 0); - - rt2x00usb_register_read(rt2x00dev, USB_CYC_CFG, ®); - rt2x00_set_field32(®, USB_CYC_CFG_CLOCK_CYCLE, 30); - rt2x00usb_register_write(rt2x00dev, USB_CYC_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, HT_FBK_CFG0, ®); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS0FBK, 0); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS1FBK, 0); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS2FBK, 1); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS3FBK, 2); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS4FBK, 3); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS5FBK, 4); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS6FBK, 5); - rt2x00_set_field32(®, HT_FBK_CFG0_HTMCS7FBK, 6); - rt2x00usb_register_write(rt2x00dev, HT_FBK_CFG0, reg); - - rt2x00usb_register_read(rt2x00dev, HT_FBK_CFG1, ®); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS8FBK, 8); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS9FBK, 8); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS10FBK, 9); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS11FBK, 10); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS12FBK, 11); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS13FBK, 12); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS14FBK, 13); - rt2x00_set_field32(®, HT_FBK_CFG1_HTMCS15FBK, 14); - rt2x00usb_register_write(rt2x00dev, HT_FBK_CFG1, reg); - - rt2x00usb_register_read(rt2x00dev, LG_FBK_CFG0, ®); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS0FBK, 8); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS1FBK, 8); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS2FBK, 9); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS3FBK, 10); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS4FBK, 11); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS5FBK, 12); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS6FBK, 13); - rt2x00_set_field32(®, LG_FBK_CFG0_OFDMMCS7FBK, 14); - rt2x00usb_register_write(rt2x00dev, LG_FBK_CFG0, reg); - - rt2x00usb_register_read(rt2x00dev, LG_FBK_CFG1, ®); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS0FBK, 0); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS1FBK, 0); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS2FBK, 1); - rt2x00_set_field32(®, LG_FBK_CFG0_CCKMCS3FBK, 2); - rt2x00usb_register_write(rt2x00dev, LG_FBK_CFG1, reg); - - /* - * We must clear the error counters. - * These registers are cleared on read, - * so we may pass a useless variable to store the value. - */ - rt2x00usb_register_read(rt2x00dev, RX_STA_CNT0, ®); - rt2x00usb_register_read(rt2x00dev, RX_STA_CNT1, ®); - rt2x00usb_register_read(rt2x00dev, RX_STA_CNT2, ®); - rt2x00usb_register_read(rt2x00dev, TX_STA_CNT0, ®); - rt2x00usb_register_read(rt2x00dev, TX_STA_CNT1, ®); - rt2x00usb_register_read(rt2x00dev, TX_STA_CNT2, ®); - - return 0; -} - -static int rt2800usb_wait_bbp_rf_ready(struct rt2x00_dev *rt2x00dev) -{ - unsigned int i; - u32 reg; - - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00usb_register_read(rt2x00dev, MAC_STATUS_CFG, ®); - if (!rt2x00_get_field32(reg, MAC_STATUS_CFG_BBP_RF_BUSY)) - return 0; - - udelay(REGISTER_BUSY_DELAY); - } - - ERROR(rt2x00dev, "BBP/RF register access failed, aborting.\n"); - return -EACCES; -} - -static int rt2800usb_wait_bbp_ready(struct rt2x00_dev *rt2x00dev) -{ - unsigned int i; - u8 value; - - /* - * BBP was enabled after firmware was loaded, - * but we need to reactivate it now. - */ - rt2x00usb_register_write(rt2x00dev, H2M_BBP_AGENT, 0); - rt2x00usb_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); - msleep(1); - - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2800usb_bbp_read(rt2x00dev, 0, &value); - if ((value != 0xff) && (value != 0x00)) - return 0; - udelay(REGISTER_BUSY_DELAY); - } - - ERROR(rt2x00dev, "BBP register access failed, aborting.\n"); - return -EACCES; -} - -static int rt2800usb_init_bbp(struct rt2x00_dev *rt2x00dev) -{ - unsigned int i; - u16 eeprom; - u8 reg_id; - u8 value; - - if (unlikely(rt2800usb_wait_bbp_rf_ready(rt2x00dev) || - rt2800usb_wait_bbp_ready(rt2x00dev))) - return -EACCES; - - rt2800usb_bbp_write(rt2x00dev, 65, 0x2c); - rt2800usb_bbp_write(rt2x00dev, 66, 0x38); - rt2800usb_bbp_write(rt2x00dev, 69, 0x12); - rt2800usb_bbp_write(rt2x00dev, 70, 0x0a); - rt2800usb_bbp_write(rt2x00dev, 73, 0x10); - rt2800usb_bbp_write(rt2x00dev, 81, 0x37); - rt2800usb_bbp_write(rt2x00dev, 82, 0x62); - rt2800usb_bbp_write(rt2x00dev, 83, 0x6a); - rt2800usb_bbp_write(rt2x00dev, 84, 0x99); - rt2800usb_bbp_write(rt2x00dev, 86, 0x00); - rt2800usb_bbp_write(rt2x00dev, 91, 0x04); - rt2800usb_bbp_write(rt2x00dev, 92, 0x00); - rt2800usb_bbp_write(rt2x00dev, 103, 0x00); - rt2800usb_bbp_write(rt2x00dev, 105, 0x05); - - if (rt2x00_rev(&rt2x00dev->chip) == RT2860C_VERSION) { - rt2800usb_bbp_write(rt2x00dev, 69, 0x16); - rt2800usb_bbp_write(rt2x00dev, 73, 0x12); - } - - if (rt2x00_rev(&rt2x00dev->chip) > RT2860D_VERSION) { - rt2800usb_bbp_write(rt2x00dev, 84, 0x19); - } - - if (rt2x00_rev(&rt2x00dev->chip) == RT3070_VERSION) { - rt2800usb_bbp_write(rt2x00dev, 70, 0x0a); - rt2800usb_bbp_write(rt2x00dev, 84, 0x99); - rt2800usb_bbp_write(rt2x00dev, 105, 0x05); - } - - for (i = 0; i < EEPROM_BBP_SIZE; i++) { - rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i, &eeprom); - - if (eeprom != 0xffff && eeprom != 0x0000) { - reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID); - value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE); - rt2800usb_bbp_write(rt2x00dev, reg_id, value); - } - } - - return 0; -} - -static u8 rt2800usb_init_rx_filter(struct rt2x00_dev *rt2x00dev, - bool bw40, u8 rfcsr24, u8 filter_target) -{ - unsigned int i; - u8 bbp; - u8 rfcsr; - u8 passband; - u8 stopband; - u8 overtuned = 0; - - rt2800usb_rfcsr_write(rt2x00dev, 24, rfcsr24); - - rt2800usb_bbp_read(rt2x00dev, 4, &bbp); - rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 2 * bw40); - rt2800usb_bbp_write(rt2x00dev, 4, bbp); - - rt2800usb_rfcsr_read(rt2x00dev, 22, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 1); - rt2800usb_rfcsr_write(rt2x00dev, 22, rfcsr); - - /* - * Set power & frequency of passband test tone - */ - rt2800usb_bbp_write(rt2x00dev, 24, 0); - - for (i = 0; i < 100; i++) { - rt2800usb_bbp_write(rt2x00dev, 25, 0x90); - msleep(1); - - rt2800usb_bbp_read(rt2x00dev, 55, &passband); - if (passband) - break; - } - - /* - * Set power & frequency of stopband test tone - */ - rt2800usb_bbp_write(rt2x00dev, 24, 0x06); - - for (i = 0; i < 100; i++) { - rt2800usb_bbp_write(rt2x00dev, 25, 0x90); - msleep(1); - - rt2800usb_bbp_read(rt2x00dev, 55, &stopband); - - if ((passband - stopband) <= filter_target) { - rfcsr24++; - overtuned += ((passband - stopband) == filter_target); - } else - break; - - rt2800usb_rfcsr_write(rt2x00dev, 24, rfcsr24); - } - - rfcsr24 -= !!overtuned; - - rt2800usb_rfcsr_write(rt2x00dev, 24, rfcsr24); - return rfcsr24; -} - -static int rt2800usb_init_rfcsr(struct rt2x00_dev *rt2x00dev) -{ - u8 rfcsr; - u8 bbp; - - if (rt2x00_rev(&rt2x00dev->chip) != RT3070_VERSION) - return 0; - - /* - * Init RF calibration. - */ - rt2800usb_rfcsr_read(rt2x00dev, 30, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 1); - rt2800usb_rfcsr_write(rt2x00dev, 30, rfcsr); - msleep(1); - rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 0); - rt2800usb_rfcsr_write(rt2x00dev, 30, rfcsr); - - rt2800usb_rfcsr_write(rt2x00dev, 4, 0x40); - rt2800usb_rfcsr_write(rt2x00dev, 5, 0x03); - rt2800usb_rfcsr_write(rt2x00dev, 6, 0x02); - rt2800usb_rfcsr_write(rt2x00dev, 7, 0x70); - rt2800usb_rfcsr_write(rt2x00dev, 9, 0x0f); - rt2800usb_rfcsr_write(rt2x00dev, 10, 0x71); - rt2800usb_rfcsr_write(rt2x00dev, 11, 0x21); - rt2800usb_rfcsr_write(rt2x00dev, 12, 0x7b); - rt2800usb_rfcsr_write(rt2x00dev, 14, 0x90); - rt2800usb_rfcsr_write(rt2x00dev, 15, 0x58); - rt2800usb_rfcsr_write(rt2x00dev, 16, 0xb3); - rt2800usb_rfcsr_write(rt2x00dev, 17, 0x92); - rt2800usb_rfcsr_write(rt2x00dev, 18, 0x2c); - rt2800usb_rfcsr_write(rt2x00dev, 19, 0x02); - rt2800usb_rfcsr_write(rt2x00dev, 20, 0xba); - rt2800usb_rfcsr_write(rt2x00dev, 21, 0xdb); - rt2800usb_rfcsr_write(rt2x00dev, 24, 0x16); - rt2800usb_rfcsr_write(rt2x00dev, 25, 0x01); - rt2800usb_rfcsr_write(rt2x00dev, 27, 0x03); - rt2800usb_rfcsr_write(rt2x00dev, 29, 0x1f); - - /* - * Set RX Filter calibration for 20MHz and 40MHz - */ - rt2x00dev->calibration[0] = - rt2800usb_init_rx_filter(rt2x00dev, false, 0x07, 0x16); - rt2x00dev->calibration[1] = - rt2800usb_init_rx_filter(rt2x00dev, true, 0x27, 0x19); - - /* - * Set back to initial state - */ - rt2800usb_bbp_write(rt2x00dev, 24, 0); - - rt2800usb_rfcsr_read(rt2x00dev, 22, &rfcsr); - rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 0); - rt2800usb_rfcsr_write(rt2x00dev, 22, rfcsr); - - /* - * set BBP back to BW20 - */ - rt2800usb_bbp_read(rt2x00dev, 4, &bbp); - rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 0); - rt2800usb_bbp_write(rt2x00dev, 4, bbp); - - return 0; -} - -/* * Device state switch handlers. */ static void rt2800usb_toggle_rx(struct rt2x00_dev *rt2x00dev, @@ -1778,11 +237,11 @@ static void rt2800usb_toggle_rx(struct rt2x00_dev *rt2x00dev, { u32 reg; - rt2x00usb_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_RX, (state == STATE_RADIO_RX_ON) || (state == STATE_RADIO_RX_ON_LINK)); - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); } static int rt2800usb_wait_wpdma_ready(struct rt2x00_dev *rt2x00dev) @@ -1791,7 +250,7 @@ static int rt2800usb_wait_wpdma_ready(struct rt2x00_dev *rt2x00dev) u32 reg; for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00usb_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); if (!rt2x00_get_field32(reg, WPDMA_GLO_CFG_TX_DMA_BUSY) && !rt2x00_get_field32(reg, WPDMA_GLO_CFG_RX_DMA_BUSY)) return 0; @@ -1812,25 +271,25 @@ static int rt2800usb_enable_radio(struct rt2x00_dev *rt2x00dev) * Initialize all registers. */ if (unlikely(rt2800usb_wait_wpdma_ready(rt2x00dev) || - rt2800usb_init_registers(rt2x00dev) || - rt2800usb_init_bbp(rt2x00dev) || - rt2800usb_init_rfcsr(rt2x00dev))) + rt2800_init_registers(rt2x00dev) || + rt2800_init_bbp(rt2x00dev) || + rt2800_init_rfcsr(rt2x00dev))) return -EIO; - rt2x00usb_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_TX, 1); - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); udelay(50); - rt2x00usb_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 1); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 1); - rt2x00usb_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - rt2x00usb_register_read(rt2x00dev, USB_DMA_CFG, ®); + rt2800_register_read(rt2x00dev, USB_DMA_CFG, ®); rt2x00_set_field32(®, USB_DMA_CFG_PHY_CLEAR, 0); /* Don't use bulk in aggregation when working with USB 1.1 */ rt2x00_set_field32(®, USB_DMA_CFG_RX_BULK_AGG_EN, @@ -1844,26 +303,26 @@ static int rt2800usb_enable_radio(struct rt2x00_dev *rt2x00dev) ((RX_ENTRIES * DATA_FRAME_SIZE) / 1024) - 3); rt2x00_set_field32(®, USB_DMA_CFG_RX_BULK_EN, 1); rt2x00_set_field32(®, USB_DMA_CFG_TX_BULK_EN, 1); - rt2x00usb_register_write(rt2x00dev, USB_DMA_CFG, reg); + rt2800_register_write(rt2x00dev, USB_DMA_CFG, reg); - rt2x00usb_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_TX, 1); rt2x00_set_field32(®, MAC_SYS_CTRL_ENABLE_RX, 1); - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); /* * Initialize LED control */ rt2x00_eeprom_read(rt2x00dev, EEPROM_LED1, &word); - rt2800usb_mcu_request(rt2x00dev, MCU_LED_1, 0xff, + rt2800_mcu_request(rt2x00dev, MCU_LED_1, 0xff, word & 0xff, (word >> 8) & 0xff); rt2x00_eeprom_read(rt2x00dev, EEPROM_LED2, &word); - rt2800usb_mcu_request(rt2x00dev, MCU_LED_2, 0xff, + rt2800_mcu_request(rt2x00dev, MCU_LED_2, 0xff, word & 0xff, (word >> 8) & 0xff); rt2x00_eeprom_read(rt2x00dev, EEPROM_LED3, &word); - rt2800usb_mcu_request(rt2x00dev, MCU_LED_3, 0xff, + rt2800_mcu_request(rt2x00dev, MCU_LED_3, 0xff, word & 0xff, (word >> 8) & 0xff); return 0; @@ -1873,14 +332,14 @@ static void rt2800usb_disable_radio(struct rt2x00_dev *rt2x00dev) { u32 reg; - rt2x00usb_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); + rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); - rt2x00usb_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); + rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - rt2x00usb_register_write(rt2x00dev, MAC_SYS_CTRL, 0); - rt2x00usb_register_write(rt2x00dev, PWR_PIN_CFG, 0); - rt2x00usb_register_write(rt2x00dev, TX_PIN_CFG, 0); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, 0); + rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0); + rt2800_register_write(rt2x00dev, TX_PIN_CFG, 0); /* Wait for DMA, ignore error */ rt2800usb_wait_wpdma_ready(rt2x00dev); @@ -1892,9 +351,9 @@ static int rt2800usb_set_state(struct rt2x00_dev *rt2x00dev, enum dev_state state) { if (state == STATE_AWAKE) - rt2800usb_mcu_request(rt2x00dev, MCU_WAKEUP, 0xff, 0, 0); + rt2800_mcu_request(rt2x00dev, MCU_WAKEUP, 0xff, 0, 0); else - rt2800usb_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0, 2); + rt2800_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0, 2); return 0; } @@ -2048,9 +507,9 @@ static void rt2800usb_write_beacon(struct queue_entry *entry) * Disable beaconing while we are reloading the beacon data, * otherwise we might be sending out invalid data. */ - rt2x00usb_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0); - rt2x00usb_register_write(rt2x00dev, BCN_TIME_CFG, reg); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); /* * Write entire beacon with descriptor to register. @@ -2093,12 +552,12 @@ static void rt2800usb_kick_tx_queue(struct rt2x00_dev *rt2x00dev, return; } - rt2x00usb_register_read(rt2x00dev, BCN_TIME_CFG, ®); + rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); if (!rt2x00_get_field32(reg, BCN_TIME_CFG_BEACON_GEN)) { rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1); rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1); rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 1); - rt2x00usb_register_write(rt2x00dev, BCN_TIME_CFG, reg); + rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); } } @@ -2124,7 +583,7 @@ static void rt2800usb_fill_rxdone(struct queue_entry *entry, */ memcpy(skbdesc->desc, rxd, skbdesc->desc_len); rxd = (__le32 *)skbdesc->desc; - rxwi = &rxd[RXD_DESC_SIZE / sizeof(__le32)]; + rxwi = &rxd[RXINFO_DESC_SIZE / sizeof(__le32)]; /* * It is now safe to read the descriptor on all architectures. @@ -2326,7 +785,7 @@ static int rt2800usb_init_eeprom(struct rt2x00_dev *rt2x00dev) * Identify RF chipset. */ value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE); - rt2x00usb_register_read(rt2x00dev, MAC_CSR0, ®); + rt2800_register_read(rt2x00dev, MAC_CSR0, ®); rt2x00_set_chip(rt2x00dev, RT2870, value, reg); /* @@ -2385,9 +844,9 @@ static int rt2800usb_init_eeprom(struct rt2x00_dev *rt2x00dev) * Store led settings, for correct led behaviour. */ #ifdef CONFIG_RT2X00_LIB_LEDS - rt2800usb_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); - rt2800usb_init_led(rt2x00dev, &rt2x00dev->led_assoc, LED_TYPE_ASSOC); - rt2800usb_init_led(rt2x00dev, &rt2x00dev->led_qual, LED_TYPE_QUALITY); + rt2800_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); + rt2800_init_led(rt2x00dev, &rt2x00dev->led_assoc, LED_TYPE_ASSOC); + rt2800_init_led(rt2x00dev, &rt2x00dev->led_qual, LED_TYPE_QUALITY); rt2x00_eeprom_read(rt2x00dev, EEPROM_FREQ, &rt2x00dev->led_mcu_reg); @@ -2600,10 +1059,25 @@ static int rt2800usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) return 0; } +static const struct rt2800_ops rt2800usb_rt2800_ops = { + .register_read = rt2x00usb_register_read, + .register_write = rt2x00usb_register_write, + .register_write_lock = rt2x00usb_register_write_lock, + + .register_multiread = rt2x00usb_register_multiread, + .register_multiwrite = rt2x00usb_register_multiwrite, + + .regbusy_read = rt2x00usb_regbusy_read, +}; + static int rt2800usb_probe_hw(struct rt2x00_dev *rt2x00dev) { int retval; + rt2x00_set_chip_intf(rt2x00dev, RT2X00_CHIP_INTF_USB); + + rt2x00dev->priv = (void *)&rt2800usb_rt2800_ops; + /* * Allocate eeprom data. */ @@ -2645,162 +1119,6 @@ static int rt2800usb_probe_hw(struct rt2x00_dev *rt2x00dev) return 0; } -/* - * IEEE80211 stack callback functions. - */ -static void rt2800usb_get_tkip_seq(struct ieee80211_hw *hw, u8 hw_key_idx, - u32 *iv32, u16 *iv16) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - struct mac_iveiv_entry iveiv_entry; - u32 offset; - - offset = MAC_IVEIV_ENTRY(hw_key_idx); - rt2x00usb_register_multiread(rt2x00dev, offset, - &iveiv_entry, sizeof(iveiv_entry)); - - memcpy(&iveiv_entry.iv[0], iv16, sizeof(iv16)); - memcpy(&iveiv_entry.iv[4], iv32, sizeof(iv32)); -} - -static int rt2800usb_set_rts_threshold(struct ieee80211_hw *hw, u32 value) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - u32 reg; - bool enabled = (value < IEEE80211_MAX_RTS_THRESHOLD); - - rt2x00usb_register_read(rt2x00dev, TX_RTS_CFG, ®); - rt2x00_set_field32(®, TX_RTS_CFG_RTS_THRES, value); - rt2x00usb_register_write(rt2x00dev, TX_RTS_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, CCK_PROT_CFG, ®); - rt2x00_set_field32(®, CCK_PROT_CFG_RTS_TH_EN, enabled); - rt2x00usb_register_write(rt2x00dev, CCK_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, OFDM_PROT_CFG, ®); - rt2x00_set_field32(®, OFDM_PROT_CFG_RTS_TH_EN, enabled); - rt2x00usb_register_write(rt2x00dev, OFDM_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, MM20_PROT_CFG, ®); - rt2x00_set_field32(®, MM20_PROT_CFG_RTS_TH_EN, enabled); - rt2x00usb_register_write(rt2x00dev, MM20_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, MM40_PROT_CFG, ®); - rt2x00_set_field32(®, MM40_PROT_CFG_RTS_TH_EN, enabled); - rt2x00usb_register_write(rt2x00dev, MM40_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, GF20_PROT_CFG, ®); - rt2x00_set_field32(®, GF20_PROT_CFG_RTS_TH_EN, enabled); - rt2x00usb_register_write(rt2x00dev, GF20_PROT_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, GF40_PROT_CFG, ®); - rt2x00_set_field32(®, GF40_PROT_CFG_RTS_TH_EN, enabled); - rt2x00usb_register_write(rt2x00dev, GF40_PROT_CFG, reg); - - return 0; -} - -static int rt2800usb_conf_tx(struct ieee80211_hw *hw, u16 queue_idx, - const struct ieee80211_tx_queue_params *params) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - struct data_queue *queue; - struct rt2x00_field32 field; - int retval; - u32 reg; - u32 offset; - - /* - * First pass the configuration through rt2x00lib, that will - * update the queue settings and validate the input. After that - * we are free to update the registers based on the value - * in the queue parameter. - */ - retval = rt2x00mac_conf_tx(hw, queue_idx, params); - if (retval) - return retval; - - /* - * We only need to perform additional register initialization - * for WMM queues/ - */ - if (queue_idx >= 4) - return 0; - - queue = rt2x00queue_get_queue(rt2x00dev, queue_idx); - - /* Update WMM TXOP register */ - offset = WMM_TXOP0_CFG + (sizeof(u32) * (!!(queue_idx & 2))); - field.bit_offset = (queue_idx & 1) * 16; - field.bit_mask = 0xffff << field.bit_offset; - - rt2x00usb_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, field, queue->txop); - rt2x00usb_register_write(rt2x00dev, offset, reg); - - /* Update WMM registers */ - field.bit_offset = queue_idx * 4; - field.bit_mask = 0xf << field.bit_offset; - - rt2x00usb_register_read(rt2x00dev, WMM_AIFSN_CFG, ®); - rt2x00_set_field32(®, field, queue->aifs); - rt2x00usb_register_write(rt2x00dev, WMM_AIFSN_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, WMM_CWMIN_CFG, ®); - rt2x00_set_field32(®, field, queue->cw_min); - rt2x00usb_register_write(rt2x00dev, WMM_CWMIN_CFG, reg); - - rt2x00usb_register_read(rt2x00dev, WMM_CWMAX_CFG, ®); - rt2x00_set_field32(®, field, queue->cw_max); - rt2x00usb_register_write(rt2x00dev, WMM_CWMAX_CFG, reg); - - /* Update EDCA registers */ - offset = EDCA_AC0_CFG + (sizeof(u32) * queue_idx); - - rt2x00usb_register_read(rt2x00dev, offset, ®); - rt2x00_set_field32(®, EDCA_AC0_CFG_TX_OP, queue->txop); - rt2x00_set_field32(®, EDCA_AC0_CFG_AIFSN, queue->aifs); - rt2x00_set_field32(®, EDCA_AC0_CFG_CWMIN, queue->cw_min); - rt2x00_set_field32(®, EDCA_AC0_CFG_CWMAX, queue->cw_max); - rt2x00usb_register_write(rt2x00dev, offset, reg); - - return 0; -} - -static u64 rt2800usb_get_tsf(struct ieee80211_hw *hw) -{ - struct rt2x00_dev *rt2x00dev = hw->priv; - u64 tsf; - u32 reg; - - rt2x00usb_register_read(rt2x00dev, TSF_TIMER_DW1, ®); - tsf = (u64) rt2x00_get_field32(reg, TSF_TIMER_DW1_HIGH_WORD) << 32; - rt2x00usb_register_read(rt2x00dev, TSF_TIMER_DW0, ®); - tsf |= rt2x00_get_field32(reg, TSF_TIMER_DW0_LOW_WORD); - - return tsf; -} - -static const struct ieee80211_ops rt2800usb_mac80211_ops = { - .tx = rt2x00mac_tx, - .start = rt2x00mac_start, - .stop = rt2x00mac_stop, - .add_interface = rt2x00mac_add_interface, - .remove_interface = rt2x00mac_remove_interface, - .config = rt2x00mac_config, - .configure_filter = rt2x00mac_configure_filter, - .set_tim = rt2x00mac_set_tim, - .set_key = rt2x00mac_set_key, - .get_stats = rt2x00mac_get_stats, - .get_tkip_seq = rt2800usb_get_tkip_seq, - .set_rts_threshold = rt2800usb_set_rts_threshold, - .bss_info_changed = rt2x00mac_bss_info_changed, - .conf_tx = rt2800usb_conf_tx, - .get_tx_stats = rt2x00mac_get_tx_stats, - .get_tsf = rt2800usb_get_tsf, - .rfkill_poll = rt2x00mac_rfkill_poll, -}; - static const struct rt2x00lib_ops rt2800usb_rt2x00_ops = { .probe_hw = rt2800usb_probe_hw, .get_firmware_name = rt2800usb_get_firmware_name, @@ -2810,10 +1128,10 @@ static const struct rt2x00lib_ops rt2800usb_rt2x00_ops = { .uninitialize = rt2x00usb_uninitialize, .clear_entry = rt2x00usb_clear_entry, .set_device_state = rt2800usb_set_device_state, - .rfkill_poll = rt2800usb_rfkill_poll, - .link_stats = rt2800usb_link_stats, - .reset_tuner = rt2800usb_reset_tuner, - .link_tuner = rt2800usb_link_tuner, + .rfkill_poll = rt2800_rfkill_poll, + .link_stats = rt2800_link_stats, + .reset_tuner = rt2800_reset_tuner, + .link_tuner = rt2800_link_tuner, .write_tx_desc = rt2800usb_write_tx_desc, .write_tx_data = rt2x00usb_write_tx_data, .write_beacon = rt2800usb_write_beacon, @@ -2821,19 +1139,19 @@ static const struct rt2x00lib_ops rt2800usb_rt2x00_ops = { .kick_tx_queue = rt2800usb_kick_tx_queue, .kill_tx_queue = rt2x00usb_kill_tx_queue, .fill_rxdone = rt2800usb_fill_rxdone, - .config_shared_key = rt2800usb_config_shared_key, - .config_pairwise_key = rt2800usb_config_pairwise_key, - .config_filter = rt2800usb_config_filter, - .config_intf = rt2800usb_config_intf, - .config_erp = rt2800usb_config_erp, - .config_ant = rt2800usb_config_ant, - .config = rt2800usb_config, + .config_shared_key = rt2800_config_shared_key, + .config_pairwise_key = rt2800_config_pairwise_key, + .config_filter = rt2800_config_filter, + .config_intf = rt2800_config_intf, + .config_erp = rt2800_config_erp, + .config_ant = rt2800_config_ant, + .config = rt2800_config, }; static const struct data_queue_desc rt2800usb_queue_rx = { .entry_num = RX_ENTRIES, .data_size = AGGREGATION_SIZE, - .desc_size = RXD_DESC_SIZE + RXWI_DESC_SIZE, + .desc_size = RXINFO_DESC_SIZE + RXWI_DESC_SIZE, .priv_size = sizeof(struct queue_entry_priv_usb), }; @@ -2862,9 +1180,9 @@ static const struct rt2x00_ops rt2800usb_ops = { .tx = &rt2800usb_queue_tx, .bcn = &rt2800usb_queue_bcn, .lib = &rt2800usb_rt2x00_ops, - .hw = &rt2800usb_mac80211_ops, + .hw = &rt2800_mac80211_ops, #ifdef CONFIG_RT2X00_LIB_DEBUGFS - .debugfs = &rt2800usb_rt2x00debug, + .debugfs = &rt2800_rt2x00debug, #endif /* CONFIG_RT2X00_LIB_DEBUGFS */ }; diff --git a/drivers/net/wireless/rt2x00/rt2800usb.h b/drivers/net/wireless/rt2x00/rt2800usb.h index 4d9991c..c9d7d40 100644 --- a/drivers/net/wireless/rt2x00/rt2800usb.h +++ b/drivers/net/wireless/rt2x00/rt2800usb.h @@ -28,288 +28,10 @@ #define RT2800USB_H /* - * RF chip defines. - * - * RF2820 2.4G 2T3R - * RF2850 2.4G/5G 2T3R - * RF2720 2.4G 1T2R - * RF2750 2.4G/5G 1T2R - * RF3020 2.4G 1T1R - * RF2020 2.4G B/G - * RF3021 2.4G 1T2R - * RF3022 2.4G 2T2R - * RF3052 2.4G 2T2R - */ -#define RF2820 0x0001 -#define RF2850 0x0002 -#define RF2720 0x0003 -#define RF2750 0x0004 -#define RF3020 0x0005 -#define RF2020 0x0006 -#define RF3021 0x0007 -#define RF3022 0x0008 -#define RF3052 0x0009 - -/* - * RT2870 version - */ -#define RT2860C_VERSION 0x28600100 -#define RT2860D_VERSION 0x28600101 -#define RT2880E_VERSION 0x28720200 -#define RT2883_VERSION 0x28830300 -#define RT3070_VERSION 0x30700200 - -/* - * Signal information. - * Defaul offset is required for RSSI <-> dBm conversion. - */ -#define DEFAULT_RSSI_OFFSET 120 /* FIXME */ - -/* - * Register layout information. - */ -#define CSR_REG_BASE 0x1000 -#define CSR_REG_SIZE 0x0800 -#define EEPROM_BASE 0x0000 -#define EEPROM_SIZE 0x0110 -#define BBP_BASE 0x0000 -#define BBP_SIZE 0x0080 -#define RF_BASE 0x0004 -#define RF_SIZE 0x0010 - -/* - * Number of TX queues. - */ -#define NUM_TX_QUEUES 4 - -/* * USB registers. */ /* - * HOST-MCU shared memory - */ -#define HOST_CMD_CSR 0x0404 -#define HOST_CMD_CSR_HOST_COMMAND FIELD32(0x000000ff) - -/* - * INT_SOURCE_CSR: Interrupt source register. - * Write one to clear corresponding bit. - * TX_FIFO_STATUS: FIFO Statistics is full, sw should read 0x171c - */ -#define INT_SOURCE_CSR 0x0200 -#define INT_SOURCE_CSR_RXDELAYINT FIELD32(0x00000001) -#define INT_SOURCE_CSR_TXDELAYINT FIELD32(0x00000002) -#define INT_SOURCE_CSR_RX_DONE FIELD32(0x00000004) -#define INT_SOURCE_CSR_AC0_DMA_DONE FIELD32(0x00000008) -#define INT_SOURCE_CSR_AC1_DMA_DONE FIELD32(0x00000010) -#define INT_SOURCE_CSR_AC2_DMA_DONE FIELD32(0x00000020) -#define INT_SOURCE_CSR_AC3_DMA_DONE FIELD32(0x00000040) -#define INT_SOURCE_CSR_HCCA_DMA_DONE FIELD32(0x00000080) -#define INT_SOURCE_CSR_MGMT_DMA_DONE FIELD32(0x00000100) -#define INT_SOURCE_CSR_MCU_COMMAND FIELD32(0x00000200) -#define INT_SOURCE_CSR_RXTX_COHERENT FIELD32(0x00000400) -#define INT_SOURCE_CSR_TBTT FIELD32(0x00000800) -#define INT_SOURCE_CSR_PRE_TBTT FIELD32(0x00001000) -#define INT_SOURCE_CSR_TX_FIFO_STATUS FIELD32(0x00002000) -#define INT_SOURCE_CSR_AUTO_WAKEUP FIELD32(0x00004000) -#define INT_SOURCE_CSR_GPTIMER FIELD32(0x00008000) -#define INT_SOURCE_CSR_RX_COHERENT FIELD32(0x00010000) -#define INT_SOURCE_CSR_TX_COHERENT FIELD32(0x00020000) - -/* - * INT_MASK_CSR: Interrupt MASK register. 1: the interrupt is mask OFF. - */ -#define INT_MASK_CSR 0x0204 -#define INT_MASK_CSR_RXDELAYINT FIELD32(0x00000001) -#define INT_MASK_CSR_TXDELAYINT FIELD32(0x00000002) -#define INT_MASK_CSR_RX_DONE FIELD32(0x00000004) -#define INT_MASK_CSR_AC0_DMA_DONE FIELD32(0x00000008) -#define INT_MASK_CSR_AC1_DMA_DONE FIELD32(0x00000010) -#define INT_MASK_CSR_AC2_DMA_DONE FIELD32(0x00000020) -#define INT_MASK_CSR_AC3_DMA_DONE FIELD32(0x00000040) -#define INT_MASK_CSR_HCCA_DMA_DONE FIELD32(0x00000080) -#define INT_MASK_CSR_MGMT_DMA_DONE FIELD32(0x00000100) -#define INT_MASK_CSR_MCU_COMMAND FIELD32(0x00000200) -#define INT_MASK_CSR_RXTX_COHERENT FIELD32(0x00000400) -#define INT_MASK_CSR_TBTT FIELD32(0x00000800) -#define INT_MASK_CSR_PRE_TBTT FIELD32(0x00001000) -#define INT_MASK_CSR_TX_FIFO_STATUS FIELD32(0x00002000) -#define INT_MASK_CSR_AUTO_WAKEUP FIELD32(0x00004000) -#define INT_MASK_CSR_GPTIMER FIELD32(0x00008000) -#define INT_MASK_CSR_RX_COHERENT FIELD32(0x00010000) -#define INT_MASK_CSR_TX_COHERENT FIELD32(0x00020000) - -/* - * WPDMA_GLO_CFG - */ -#define WPDMA_GLO_CFG 0x0208 -#define WPDMA_GLO_CFG_ENABLE_TX_DMA FIELD32(0x00000001) -#define WPDMA_GLO_CFG_TX_DMA_BUSY FIELD32(0x00000002) -#define WPDMA_GLO_CFG_ENABLE_RX_DMA FIELD32(0x00000004) -#define WPDMA_GLO_CFG_RX_DMA_BUSY FIELD32(0x00000008) -#define WPDMA_GLO_CFG_WP_DMA_BURST_SIZE FIELD32(0x00000030) -#define WPDMA_GLO_CFG_TX_WRITEBACK_DONE FIELD32(0x00000040) -#define WPDMA_GLO_CFG_BIG_ENDIAN FIELD32(0x00000080) -#define WPDMA_GLO_CFG_RX_HDR_SCATTER FIELD32(0x0000ff00) -#define WPDMA_GLO_CFG_HDR_SEG_LEN FIELD32(0xffff0000) - -/* - * WPDMA_RST_IDX - */ -#define WPDMA_RST_IDX 0x020c -#define WPDMA_RST_IDX_DTX_IDX0 FIELD32(0x00000001) -#define WPDMA_RST_IDX_DTX_IDX1 FIELD32(0x00000002) -#define WPDMA_RST_IDX_DTX_IDX2 FIELD32(0x00000004) -#define WPDMA_RST_IDX_DTX_IDX3 FIELD32(0x00000008) -#define WPDMA_RST_IDX_DTX_IDX4 FIELD32(0x00000010) -#define WPDMA_RST_IDX_DTX_IDX5 FIELD32(0x00000020) -#define WPDMA_RST_IDX_DRX_IDX0 FIELD32(0x00010000) - -/* - * DELAY_INT_CFG - */ -#define DELAY_INT_CFG 0x0210 -#define DELAY_INT_CFG_RXMAX_PTIME FIELD32(0x000000ff) -#define DELAY_INT_CFG_RXMAX_PINT FIELD32(0x00007f00) -#define DELAY_INT_CFG_RXDLY_INT_EN FIELD32(0x00008000) -#define DELAY_INT_CFG_TXMAX_PTIME FIELD32(0x00ff0000) -#define DELAY_INT_CFG_TXMAX_PINT FIELD32(0x7f000000) -#define DELAY_INT_CFG_TXDLY_INT_EN FIELD32(0x80000000) - -/* - * WMM_AIFSN_CFG: Aifsn for each EDCA AC - * AIFSN0: AC_BE - * AIFSN1: AC_BK - * AIFSN1: AC_VI - * AIFSN1: AC_VO - */ -#define WMM_AIFSN_CFG 0x0214 -#define WMM_AIFSN_CFG_AIFSN0 FIELD32(0x0000000f) -#define WMM_AIFSN_CFG_AIFSN1 FIELD32(0x000000f0) -#define WMM_AIFSN_CFG_AIFSN2 FIELD32(0x00000f00) -#define WMM_AIFSN_CFG_AIFSN3 FIELD32(0x0000f000) - -/* - * WMM_CWMIN_CSR: CWmin for each EDCA AC - * CWMIN0: AC_BE - * CWMIN1: AC_BK - * CWMIN1: AC_VI - * CWMIN1: AC_VO - */ -#define WMM_CWMIN_CFG 0x0218 -#define WMM_CWMIN_CFG_CWMIN0 FIELD32(0x0000000f) -#define WMM_CWMIN_CFG_CWMIN1 FIELD32(0x000000f0) -#define WMM_CWMIN_CFG_CWMIN2 FIELD32(0x00000f00) -#define WMM_CWMIN_CFG_CWMIN3 FIELD32(0x0000f000) - -/* - * WMM_CWMAX_CSR: CWmax for each EDCA AC - * CWMAX0: AC_BE - * CWMAX1: AC_BK - * CWMAX1: AC_VI - * CWMAX1: AC_VO - */ -#define WMM_CWMAX_CFG 0x021c -#define WMM_CWMAX_CFG_CWMAX0 FIELD32(0x0000000f) -#define WMM_CWMAX_CFG_CWMAX1 FIELD32(0x000000f0) -#define WMM_CWMAX_CFG_CWMAX2 FIELD32(0x00000f00) -#define WMM_CWMAX_CFG_CWMAX3 FIELD32(0x0000f000) - -/* - * AC_TXOP0: AC_BK/AC_BE TXOP register - * AC0TXOP: AC_BK in unit of 32us - * AC1TXOP: AC_BE in unit of 32us - */ -#define WMM_TXOP0_CFG 0x0220 -#define WMM_TXOP0_CFG_AC0TXOP FIELD32(0x0000ffff) -#define WMM_TXOP0_CFG_AC1TXOP FIELD32(0xffff0000) - -/* - * AC_TXOP1: AC_VO/AC_VI TXOP register - * AC2TXOP: AC_VI in unit of 32us - * AC3TXOP: AC_VO in unit of 32us - */ -#define WMM_TXOP1_CFG 0x0224 -#define WMM_TXOP1_CFG_AC2TXOP FIELD32(0x0000ffff) -#define WMM_TXOP1_CFG_AC3TXOP FIELD32(0xffff0000) - -/* - * GPIO_CTRL_CFG: - */ -#define GPIO_CTRL_CFG 0x0228 -#define GPIO_CTRL_CFG_BIT0 FIELD32(0x00000001) -#define GPIO_CTRL_CFG_BIT1 FIELD32(0x00000002) -#define GPIO_CTRL_CFG_BIT2 FIELD32(0x00000004) -#define GPIO_CTRL_CFG_BIT3 FIELD32(0x00000008) -#define GPIO_CTRL_CFG_BIT4 FIELD32(0x00000010) -#define GPIO_CTRL_CFG_BIT5 FIELD32(0x00000020) -#define GPIO_CTRL_CFG_BIT6 FIELD32(0x00000040) -#define GPIO_CTRL_CFG_BIT7 FIELD32(0x00000080) -#define GPIO_CTRL_CFG_BIT8 FIELD32(0x00000100) - -/* - * MCU_CMD_CFG - */ -#define MCU_CMD_CFG 0x022c - -/* - * AC_BK register offsets - */ -#define TX_BASE_PTR0 0x0230 -#define TX_MAX_CNT0 0x0234 -#define TX_CTX_IDX0 0x0238 -#define TX_DTX_IDX0 0x023c - -/* - * AC_BE register offsets - */ -#define TX_BASE_PTR1 0x0240 -#define TX_MAX_CNT1 0x0244 -#define TX_CTX_IDX1 0x0248 -#define TX_DTX_IDX1 0x024c - -/* - * AC_VI register offsets - */ -#define TX_BASE_PTR2 0x0250 -#define TX_MAX_CNT2 0x0254 -#define TX_CTX_IDX2 0x0258 -#define TX_DTX_IDX2 0x025c - -/* - * AC_VO register offsets - */ -#define TX_BASE_PTR3 0x0260 -#define TX_MAX_CNT3 0x0264 -#define TX_CTX_IDX3 0x0268 -#define TX_DTX_IDX3 0x026c - -/* - * HCCA register offsets - */ -#define TX_BASE_PTR4 0x0270 -#define TX_MAX_CNT4 0x0274 -#define TX_CTX_IDX4 0x0278 -#define TX_DTX_IDX4 0x027c - -/* - * MGMT register offsets - */ -#define TX_BASE_PTR5 0x0280 -#define TX_MAX_CNT5 0x0284 -#define TX_CTX_IDX5 0x0288 -#define TX_DTX_IDX5 0x028c - -/* - * RX register offsets - */ -#define RX_BASE_PTR 0x0290 -#define RX_MAX_CNT 0x0294 -#define RX_CRX_IDX 0x0298 -#define RX_DRX_IDX 0x029c - -/* * USB_DMA_CFG * RX_BULK_AGG_TIMEOUT: Rx Bulk Aggregation TimeOut in unit of 33ns. * RX_BULK_AGG_LIMIT: Rx Bulk Aggregation Limit in unit of 256 bytes. @@ -343,1448 +65,16 @@ #define USB_CYC_CFG_CLOCK_CYCLE FIELD32(0x000000ff) /* - * PBF_SYS_CTRL - * HOST_RAM_WRITE: enable Host program ram write selection - */ -#define PBF_SYS_CTRL 0x0400 -#define PBF_SYS_CTRL_READY FIELD32(0x00000080) -#define PBF_SYS_CTRL_HOST_RAM_WRITE FIELD32(0x00010000) - -/* - * PBF registers - * Most are for debug. Driver doesn't touch PBF register. - */ -#define PBF_CFG 0x0408 -#define PBF_MAX_PCNT 0x040c -#define PBF_CTRL 0x0410 -#define PBF_INT_STA 0x0414 -#define PBF_INT_ENA 0x0418 - -/* - * BCN_OFFSET0: - */ -#define BCN_OFFSET0 0x042c -#define BCN_OFFSET0_BCN0 FIELD32(0x000000ff) -#define BCN_OFFSET0_BCN1 FIELD32(0x0000ff00) -#define BCN_OFFSET0_BCN2 FIELD32(0x00ff0000) -#define BCN_OFFSET0_BCN3 FIELD32(0xff000000) - -/* - * BCN_OFFSET1: - */ -#define BCN_OFFSET1 0x0430 -#define BCN_OFFSET1_BCN4 FIELD32(0x000000ff) -#define BCN_OFFSET1_BCN5 FIELD32(0x0000ff00) -#define BCN_OFFSET1_BCN6 FIELD32(0x00ff0000) -#define BCN_OFFSET1_BCN7 FIELD32(0xff000000) - -/* - * PBF registers - * Most are for debug. Driver doesn't touch PBF register. - */ -#define TXRXQ_PCNT 0x0438 -#define PBF_DBG 0x043c - -/* - * RF registers - */ -#define RF_CSR_CFG 0x0500 -#define RF_CSR_CFG_DATA FIELD32(0x000000ff) -#define RF_CSR_CFG_REGNUM FIELD32(0x00001f00) -#define RF_CSR_CFG_WRITE FIELD32(0x00010000) -#define RF_CSR_CFG_BUSY FIELD32(0x00020000) - -/* - * MAC Control/Status Registers(CSR). - * Some values are set in TU, whereas 1 TU == 1024 us. - */ - -/* - * MAC_CSR0: ASIC revision number. - * ASIC_REV: 0 - * ASIC_VER: 2870 - */ -#define MAC_CSR0 0x1000 -#define MAC_CSR0_ASIC_REV FIELD32(0x0000ffff) -#define MAC_CSR0_ASIC_VER FIELD32(0xffff0000) - -/* - * MAC_SYS_CTRL: - */ -#define MAC_SYS_CTRL 0x1004 -#define MAC_SYS_CTRL_RESET_CSR FIELD32(0x00000001) -#define MAC_SYS_CTRL_RESET_BBP FIELD32(0x00000002) -#define MAC_SYS_CTRL_ENABLE_TX FIELD32(0x00000004) -#define MAC_SYS_CTRL_ENABLE_RX FIELD32(0x00000008) -#define MAC_SYS_CTRL_CONTINUOUS_TX FIELD32(0x00000010) -#define MAC_SYS_CTRL_LOOPBACK FIELD32(0x00000020) -#define MAC_SYS_CTRL_WLAN_HALT FIELD32(0x00000040) -#define MAC_SYS_CTRL_RX_TIMESTAMP FIELD32(0x00000080) - -/* - * MAC_ADDR_DW0: STA MAC register 0 - */ -#define MAC_ADDR_DW0 0x1008 -#define MAC_ADDR_DW0_BYTE0 FIELD32(0x000000ff) -#define MAC_ADDR_DW0_BYTE1 FIELD32(0x0000ff00) -#define MAC_ADDR_DW0_BYTE2 FIELD32(0x00ff0000) -#define MAC_ADDR_DW0_BYTE3 FIELD32(0xff000000) - -/* - * MAC_ADDR_DW1: STA MAC register 1 - * UNICAST_TO_ME_MASK: - * Used to mask off bits from byte 5 of the MAC address - * to determine the UNICAST_TO_ME bit for RX frames. - * The full mask is complemented by BSS_ID_MASK: - * MASK = BSS_ID_MASK & UNICAST_TO_ME_MASK - */ -#define MAC_ADDR_DW1 0x100c -#define MAC_ADDR_DW1_BYTE4 FIELD32(0x000000ff) -#define MAC_ADDR_DW1_BYTE5 FIELD32(0x0000ff00) -#define MAC_ADDR_DW1_UNICAST_TO_ME_MASK FIELD32(0x00ff0000) - -/* - * MAC_BSSID_DW0: BSSID register 0 - */ -#define MAC_BSSID_DW0 0x1010 -#define MAC_BSSID_DW0_BYTE0 FIELD32(0x000000ff) -#define MAC_BSSID_DW0_BYTE1 FIELD32(0x0000ff00) -#define MAC_BSSID_DW0_BYTE2 FIELD32(0x00ff0000) -#define MAC_BSSID_DW0_BYTE3 FIELD32(0xff000000) - -/* - * MAC_BSSID_DW1: BSSID register 1 - * BSS_ID_MASK: - * 0: 1-BSSID mode (BSS index = 0) - * 1: 2-BSSID mode (BSS index: Byte5, bit 0) - * 2: 4-BSSID mode (BSS index: byte5, bit 0 - 1) - * 3: 8-BSSID mode (BSS index: byte5, bit 0 - 2) - * This mask is used to mask off bits 0, 1 and 2 of byte 5 of the - * BSSID. This will make sure that those bits will be ignored - * when determining the MY_BSS of RX frames. - */ -#define MAC_BSSID_DW1 0x1014 -#define MAC_BSSID_DW1_BYTE4 FIELD32(0x000000ff) -#define MAC_BSSID_DW1_BYTE5 FIELD32(0x0000ff00) -#define MAC_BSSID_DW1_BSS_ID_MASK FIELD32(0x00030000) -#define MAC_BSSID_DW1_BSS_BCN_NUM FIELD32(0x001c0000) - -/* - * MAX_LEN_CFG: Maximum frame length register. - * MAX_MPDU: rt2860b max 16k bytes - * MAX_PSDU: Maximum PSDU length - * (power factor) 0:2^13, 1:2^14, 2:2^15, 3:2^16 - */ -#define MAX_LEN_CFG 0x1018 -#define MAX_LEN_CFG_MAX_MPDU FIELD32(0x00000fff) -#define MAX_LEN_CFG_MAX_PSDU FIELD32(0x00003000) -#define MAX_LEN_CFG_MIN_PSDU FIELD32(0x0000c000) -#define MAX_LEN_CFG_MIN_MPDU FIELD32(0x000f0000) - -/* - * BBP_CSR_CFG: BBP serial control register - * VALUE: Register value to program into BBP - * REG_NUM: Selected BBP register - * READ_CONTROL: 0 write BBP, 1 read BBP - * BUSY: ASIC is busy executing BBP commands - * BBP_PAR_DUR: 0 4 MAC clocks, 1 8 MAC clocks - * BBP_RW_MODE: 0 serial, 1 paralell - */ -#define BBP_CSR_CFG 0x101c -#define BBP_CSR_CFG_VALUE FIELD32(0x000000ff) -#define BBP_CSR_CFG_REGNUM FIELD32(0x0000ff00) -#define BBP_CSR_CFG_READ_CONTROL FIELD32(0x00010000) -#define BBP_CSR_CFG_BUSY FIELD32(0x00020000) -#define BBP_CSR_CFG_BBP_PAR_DUR FIELD32(0x00040000) -#define BBP_CSR_CFG_BBP_RW_MODE FIELD32(0x00080000) - -/* - * RF_CSR_CFG0: RF control register - * REGID_AND_VALUE: Register value to program into RF - * BITWIDTH: Selected RF register - * STANDBYMODE: 0 high when standby, 1 low when standby - * SEL: 0 RF_LE0 activate, 1 RF_LE1 activate - * BUSY: ASIC is busy executing RF commands - */ -#define RF_CSR_CFG0 0x1020 -#define RF_CSR_CFG0_REGID_AND_VALUE FIELD32(0x00ffffff) -#define RF_CSR_CFG0_BITWIDTH FIELD32(0x1f000000) -#define RF_CSR_CFG0_REG_VALUE_BW FIELD32(0x1fffffff) -#define RF_CSR_CFG0_STANDBYMODE FIELD32(0x20000000) -#define RF_CSR_CFG0_SEL FIELD32(0x40000000) -#define RF_CSR_CFG0_BUSY FIELD32(0x80000000) - -/* - * RF_CSR_CFG1: RF control register - * REGID_AND_VALUE: Register value to program into RF - * RFGAP: Gap between BB_CONTROL_RF and RF_LE - * 0: 3 system clock cycle (37.5usec) - * 1: 5 system clock cycle (62.5usec) - */ -#define RF_CSR_CFG1 0x1024 -#define RF_CSR_CFG1_REGID_AND_VALUE FIELD32(0x00ffffff) -#define RF_CSR_CFG1_RFGAP FIELD32(0x1f000000) - -/* - * RF_CSR_CFG2: RF control register - * VALUE: Register value to program into RF - * RFGAP: Gap between BB_CONTROL_RF and RF_LE - * 0: 3 system clock cycle (37.5usec) - * 1: 5 system clock cycle (62.5usec) - */ -#define RF_CSR_CFG2 0x1028 -#define RF_CSR_CFG2_VALUE FIELD32(0x00ffffff) - -/* - * LED_CFG: LED control - * color LED's: - * 0: off - * 1: blinking upon TX2 - * 2: periodic slow blinking - * 3: always on - * LED polarity: - * 0: active low - * 1: active high - */ -#define LED_CFG 0x102c -#define LED_CFG_ON_PERIOD FIELD32(0x000000ff) -#define LED_CFG_OFF_PERIOD FIELD32(0x0000ff00) -#define LED_CFG_SLOW_BLINK_PERIOD FIELD32(0x003f0000) -#define LED_CFG_R_LED_MODE FIELD32(0x03000000) -#define LED_CFG_G_LED_MODE FIELD32(0x0c000000) -#define LED_CFG_Y_LED_MODE FIELD32(0x30000000) -#define LED_CFG_LED_POLAR FIELD32(0x40000000) - -/* - * XIFS_TIME_CFG: MAC timing - * CCKM_SIFS_TIME: unit 1us. Applied after CCK RX/TX - * OFDM_SIFS_TIME: unit 1us. Applied after OFDM RX/TX - * OFDM_XIFS_TIME: unit 1us. Applied after OFDM RX - * when MAC doesn't reference BBP signal BBRXEND - * EIFS: unit 1us - * BB_RXEND_ENABLE: reference RXEND signal to begin XIFS defer - * - */ -#define XIFS_TIME_CFG 0x1100 -#define XIFS_TIME_CFG_CCKM_SIFS_TIME FIELD32(0x000000ff) -#define XIFS_TIME_CFG_OFDM_SIFS_TIME FIELD32(0x0000ff00) -#define XIFS_TIME_CFG_OFDM_XIFS_TIME FIELD32(0x000f0000) -#define XIFS_TIME_CFG_EIFS FIELD32(0x1ff00000) -#define XIFS_TIME_CFG_BB_RXEND_ENABLE FIELD32(0x20000000) - -/* - * BKOFF_SLOT_CFG: - */ -#define BKOFF_SLOT_CFG 0x1104 -#define BKOFF_SLOT_CFG_SLOT_TIME FIELD32(0x000000ff) -#define BKOFF_SLOT_CFG_CC_DELAY_TIME FIELD32(0x0000ff00) - -/* - * NAV_TIME_CFG: - */ -#define NAV_TIME_CFG 0x1108 -#define NAV_TIME_CFG_SIFS FIELD32(0x000000ff) -#define NAV_TIME_CFG_SLOT_TIME FIELD32(0x0000ff00) -#define NAV_TIME_CFG_EIFS FIELD32(0x01ff0000) -#define NAV_TIME_ZERO_SIFS FIELD32(0x02000000) - -/* - * CH_TIME_CFG: count as channel busy - */ -#define CH_TIME_CFG 0x110c - -/* - * PBF_LIFE_TIMER: TX/RX MPDU timestamp timer (free run) Unit: 1us - */ -#define PBF_LIFE_TIMER 0x1110 - -/* - * BCN_TIME_CFG: - * BEACON_INTERVAL: in unit of 1/16 TU - * TSF_TICKING: Enable TSF auto counting - * TSF_SYNC: Enable TSF sync, 00: disable, 01: infra mode, 10: ad-hoc mode - * BEACON_GEN: Enable beacon generator - */ -#define BCN_TIME_CFG 0x1114 -#define BCN_TIME_CFG_BEACON_INTERVAL FIELD32(0x0000ffff) -#define BCN_TIME_CFG_TSF_TICKING FIELD32(0x00010000) -#define BCN_TIME_CFG_TSF_SYNC FIELD32(0x00060000) -#define BCN_TIME_CFG_TBTT_ENABLE FIELD32(0x00080000) -#define BCN_TIME_CFG_BEACON_GEN FIELD32(0x00100000) -#define BCN_TIME_CFG_TX_TIME_COMPENSATE FIELD32(0xf0000000) - -/* - * TBTT_SYNC_CFG: - */ -#define TBTT_SYNC_CFG 0x1118 - -/* - * TSF_TIMER_DW0: Local lsb TSF timer, read-only - */ -#define TSF_TIMER_DW0 0x111c -#define TSF_TIMER_DW0_LOW_WORD FIELD32(0xffffffff) - -/* - * TSF_TIMER_DW1: Local msb TSF timer, read-only - */ -#define TSF_TIMER_DW1 0x1120 -#define TSF_TIMER_DW1_HIGH_WORD FIELD32(0xffffffff) - -/* - * TBTT_TIMER: TImer remains till next TBTT, read-only - */ -#define TBTT_TIMER 0x1124 - -/* - * INT_TIMER_CFG: - */ -#define INT_TIMER_CFG 0x1128 - -/* - * INT_TIMER_EN: GP-timer and pre-tbtt Int enable - */ -#define INT_TIMER_EN 0x112c - -/* - * CH_IDLE_STA: channel idle time - */ -#define CH_IDLE_STA 0x1130 - -/* - * CH_BUSY_STA: channel busy time - */ -#define CH_BUSY_STA 0x1134 - -/* - * MAC_STATUS_CFG: - * BBP_RF_BUSY: When set to 0, BBP and RF are stable. - * if 1 or higher one of the 2 registers is busy. - */ -#define MAC_STATUS_CFG 0x1200 -#define MAC_STATUS_CFG_BBP_RF_BUSY FIELD32(0x00000003) - -/* - * PWR_PIN_CFG: - */ -#define PWR_PIN_CFG 0x1204 - -/* - * AUTOWAKEUP_CFG: Manual power control / status register - * TBCN_BEFORE_WAKE: ForceWake has high privilege than PutToSleep when both set - * AUTOWAKE: 0:sleep, 1:awake - */ -#define AUTOWAKEUP_CFG 0x1208 -#define AUTOWAKEUP_CFG_AUTO_LEAD_TIME FIELD32(0x000000ff) -#define AUTOWAKEUP_CFG_TBCN_BEFORE_WAKE FIELD32(0x00007f00) -#define AUTOWAKEUP_CFG_AUTOWAKE FIELD32(0x00008000) - -/* - * EDCA_AC0_CFG: - */ -#define EDCA_AC0_CFG 0x1300 -#define EDCA_AC0_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC0_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC0_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC0_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_AC1_CFG: - */ -#define EDCA_AC1_CFG 0x1304 -#define EDCA_AC1_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC1_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC1_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC1_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_AC2_CFG: - */ -#define EDCA_AC2_CFG 0x1308 -#define EDCA_AC2_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC2_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC2_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC2_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_AC3_CFG: - */ -#define EDCA_AC3_CFG 0x130c -#define EDCA_AC3_CFG_TX_OP FIELD32(0x000000ff) -#define EDCA_AC3_CFG_AIFSN FIELD32(0x00000f00) -#define EDCA_AC3_CFG_CWMIN FIELD32(0x0000f000) -#define EDCA_AC3_CFG_CWMAX FIELD32(0x000f0000) - -/* - * EDCA_TID_AC_MAP: - */ -#define EDCA_TID_AC_MAP 0x1310 - -/* - * TX_PWR_CFG_0: - */ -#define TX_PWR_CFG_0 0x1314 -#define TX_PWR_CFG_0_1MBS FIELD32(0x0000000f) -#define TX_PWR_CFG_0_2MBS FIELD32(0x000000f0) -#define TX_PWR_CFG_0_55MBS FIELD32(0x00000f00) -#define TX_PWR_CFG_0_11MBS FIELD32(0x0000f000) -#define TX_PWR_CFG_0_6MBS FIELD32(0x000f0000) -#define TX_PWR_CFG_0_9MBS FIELD32(0x00f00000) -#define TX_PWR_CFG_0_12MBS FIELD32(0x0f000000) -#define TX_PWR_CFG_0_18MBS FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_1: - */ -#define TX_PWR_CFG_1 0x1318 -#define TX_PWR_CFG_1_24MBS FIELD32(0x0000000f) -#define TX_PWR_CFG_1_36MBS FIELD32(0x000000f0) -#define TX_PWR_CFG_1_48MBS FIELD32(0x00000f00) -#define TX_PWR_CFG_1_54MBS FIELD32(0x0000f000) -#define TX_PWR_CFG_1_MCS0 FIELD32(0x000f0000) -#define TX_PWR_CFG_1_MCS1 FIELD32(0x00f00000) -#define TX_PWR_CFG_1_MCS2 FIELD32(0x0f000000) -#define TX_PWR_CFG_1_MCS3 FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_2: - */ -#define TX_PWR_CFG_2 0x131c -#define TX_PWR_CFG_2_MCS4 FIELD32(0x0000000f) -#define TX_PWR_CFG_2_MCS5 FIELD32(0x000000f0) -#define TX_PWR_CFG_2_MCS6 FIELD32(0x00000f00) -#define TX_PWR_CFG_2_MCS7 FIELD32(0x0000f000) -#define TX_PWR_CFG_2_MCS8 FIELD32(0x000f0000) -#define TX_PWR_CFG_2_MCS9 FIELD32(0x00f00000) -#define TX_PWR_CFG_2_MCS10 FIELD32(0x0f000000) -#define TX_PWR_CFG_2_MCS11 FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_3: - */ -#define TX_PWR_CFG_3 0x1320 -#define TX_PWR_CFG_3_MCS12 FIELD32(0x0000000f) -#define TX_PWR_CFG_3_MCS13 FIELD32(0x000000f0) -#define TX_PWR_CFG_3_MCS14 FIELD32(0x00000f00) -#define TX_PWR_CFG_3_MCS15 FIELD32(0x0000f000) -#define TX_PWR_CFG_3_UKNOWN1 FIELD32(0x000f0000) -#define TX_PWR_CFG_3_UKNOWN2 FIELD32(0x00f00000) -#define TX_PWR_CFG_3_UKNOWN3 FIELD32(0x0f000000) -#define TX_PWR_CFG_3_UKNOWN4 FIELD32(0xf0000000) - -/* - * TX_PWR_CFG_4: - */ -#define TX_PWR_CFG_4 0x1324 -#define TX_PWR_CFG_4_UKNOWN5 FIELD32(0x0000000f) -#define TX_PWR_CFG_4_UKNOWN6 FIELD32(0x000000f0) -#define TX_PWR_CFG_4_UKNOWN7 FIELD32(0x00000f00) -#define TX_PWR_CFG_4_UKNOWN8 FIELD32(0x0000f000) - -/* - * TX_PIN_CFG: - */ -#define TX_PIN_CFG 0x1328 -#define TX_PIN_CFG_PA_PE_A0_EN FIELD32(0x00000001) -#define TX_PIN_CFG_PA_PE_G0_EN FIELD32(0x00000002) -#define TX_PIN_CFG_PA_PE_A1_EN FIELD32(0x00000004) -#define TX_PIN_CFG_PA_PE_G1_EN FIELD32(0x00000008) -#define TX_PIN_CFG_PA_PE_A0_POL FIELD32(0x00000010) -#define TX_PIN_CFG_PA_PE_G0_POL FIELD32(0x00000020) -#define TX_PIN_CFG_PA_PE_A1_POL FIELD32(0x00000040) -#define TX_PIN_CFG_PA_PE_G1_POL FIELD32(0x00000080) -#define TX_PIN_CFG_LNA_PE_A0_EN FIELD32(0x00000100) -#define TX_PIN_CFG_LNA_PE_G0_EN FIELD32(0x00000200) -#define TX_PIN_CFG_LNA_PE_A1_EN FIELD32(0x00000400) -#define TX_PIN_CFG_LNA_PE_G1_EN FIELD32(0x00000800) -#define TX_PIN_CFG_LNA_PE_A0_POL FIELD32(0x00001000) -#define TX_PIN_CFG_LNA_PE_G0_POL FIELD32(0x00002000) -#define TX_PIN_CFG_LNA_PE_A1_POL FIELD32(0x00004000) -#define TX_PIN_CFG_LNA_PE_G1_POL FIELD32(0x00008000) -#define TX_PIN_CFG_RFTR_EN FIELD32(0x00010000) -#define TX_PIN_CFG_RFTR_POL FIELD32(0x00020000) -#define TX_PIN_CFG_TRSW_EN FIELD32(0x00040000) -#define TX_PIN_CFG_TRSW_POL FIELD32(0x00080000) - -/* - * TX_BAND_CFG: 0x1 use upper 20MHz, 0x0 use lower 20MHz - */ -#define TX_BAND_CFG 0x132c -#define TX_BAND_CFG_HT40_PLUS FIELD32(0x00000001) -#define TX_BAND_CFG_A FIELD32(0x00000002) -#define TX_BAND_CFG_BG FIELD32(0x00000004) - -/* - * TX_SW_CFG0: - */ -#define TX_SW_CFG0 0x1330 - -/* - * TX_SW_CFG1: - */ -#define TX_SW_CFG1 0x1334 - -/* - * TX_SW_CFG2: - */ -#define TX_SW_CFG2 0x1338 - -/* - * TXOP_THRES_CFG: - */ -#define TXOP_THRES_CFG 0x133c - -/* - * TXOP_CTRL_CFG: - */ -#define TXOP_CTRL_CFG 0x1340 - -/* - * TX_RTS_CFG: - * RTS_THRES: unit:byte - * RTS_FBK_EN: enable rts rate fallback - */ -#define TX_RTS_CFG 0x1344 -#define TX_RTS_CFG_AUTO_RTS_RETRY_LIMIT FIELD32(0x000000ff) -#define TX_RTS_CFG_RTS_THRES FIELD32(0x00ffff00) -#define TX_RTS_CFG_RTS_FBK_EN FIELD32(0x01000000) - -/* - * TX_TIMEOUT_CFG: - * MPDU_LIFETIME: expiration time = 2^(9+MPDU LIFE TIME) us - * RX_ACK_TIMEOUT: unit:slot. Used for TX procedure - * TX_OP_TIMEOUT: TXOP timeout value for TXOP truncation. - * it is recommended that: - * (SLOT_TIME) > (TX_OP_TIMEOUT) > (RX_ACK_TIMEOUT) - */ -#define TX_TIMEOUT_CFG 0x1348 -#define TX_TIMEOUT_CFG_MPDU_LIFETIME FIELD32(0x000000f0) -#define TX_TIMEOUT_CFG_RX_ACK_TIMEOUT FIELD32(0x0000ff00) -#define TX_TIMEOUT_CFG_TX_OP_TIMEOUT FIELD32(0x00ff0000) - -/* - * TX_RTY_CFG: - * SHORT_RTY_LIMIT: short retry limit - * LONG_RTY_LIMIT: long retry limit - * LONG_RTY_THRE: Long retry threshoold - * NON_AGG_RTY_MODE: Non-Aggregate MPDU retry mode - * 0:expired by retry limit, 1: expired by mpdu life timer - * AGG_RTY_MODE: Aggregate MPDU retry mode - * 0:expired by retry limit, 1: expired by mpdu life timer - * TX_AUTO_FB_ENABLE: Tx retry PHY rate auto fallback enable - */ -#define TX_RTY_CFG 0x134c -#define TX_RTY_CFG_SHORT_RTY_LIMIT FIELD32(0x000000ff) -#define TX_RTY_CFG_LONG_RTY_LIMIT FIELD32(0x0000ff00) -#define TX_RTY_CFG_LONG_RTY_THRE FIELD32(0x0fff0000) -#define TX_RTY_CFG_NON_AGG_RTY_MODE FIELD32(0x10000000) -#define TX_RTY_CFG_AGG_RTY_MODE FIELD32(0x20000000) -#define TX_RTY_CFG_TX_AUTO_FB_ENABLE FIELD32(0x40000000) - -/* - * TX_LINK_CFG: - * REMOTE_MFB_LIFETIME: remote MFB life time. unit: 32us - * MFB_ENABLE: TX apply remote MFB 1:enable - * REMOTE_UMFS_ENABLE: remote unsolicit MFB enable - * 0: not apply remote remote unsolicit (MFS=7) - * TX_MRQ_EN: MCS request TX enable - * TX_RDG_EN: RDG TX enable - * TX_CF_ACK_EN: Piggyback CF-ACK enable - * REMOTE_MFB: remote MCS feedback - * REMOTE_MFS: remote MCS feedback sequence number - */ -#define TX_LINK_CFG 0x1350 -#define TX_LINK_CFG_REMOTE_MFB_LIFETIME FIELD32(0x000000ff) -#define TX_LINK_CFG_MFB_ENABLE FIELD32(0x00000100) -#define TX_LINK_CFG_REMOTE_UMFS_ENABLE FIELD32(0x00000200) -#define TX_LINK_CFG_TX_MRQ_EN FIELD32(0x00000400) -#define TX_LINK_CFG_TX_RDG_EN FIELD32(0x00000800) -#define TX_LINK_CFG_TX_CF_ACK_EN FIELD32(0x00001000) -#define TX_LINK_CFG_REMOTE_MFB FIELD32(0x00ff0000) -#define TX_LINK_CFG_REMOTE_MFS FIELD32(0xff000000) - -/* - * HT_FBK_CFG0: - */ -#define HT_FBK_CFG0 0x1354 -#define HT_FBK_CFG0_HTMCS0FBK FIELD32(0x0000000f) -#define HT_FBK_CFG0_HTMCS1FBK FIELD32(0x000000f0) -#define HT_FBK_CFG0_HTMCS2FBK FIELD32(0x00000f00) -#define HT_FBK_CFG0_HTMCS3FBK FIELD32(0x0000f000) -#define HT_FBK_CFG0_HTMCS4FBK FIELD32(0x000f0000) -#define HT_FBK_CFG0_HTMCS5FBK FIELD32(0x00f00000) -#define HT_FBK_CFG0_HTMCS6FBK FIELD32(0x0f000000) -#define HT_FBK_CFG0_HTMCS7FBK FIELD32(0xf0000000) - -/* - * HT_FBK_CFG1: - */ -#define HT_FBK_CFG1 0x1358 -#define HT_FBK_CFG1_HTMCS8FBK FIELD32(0x0000000f) -#define HT_FBK_CFG1_HTMCS9FBK FIELD32(0x000000f0) -#define HT_FBK_CFG1_HTMCS10FBK FIELD32(0x00000f00) -#define HT_FBK_CFG1_HTMCS11FBK FIELD32(0x0000f000) -#define HT_FBK_CFG1_HTMCS12FBK FIELD32(0x000f0000) -#define HT_FBK_CFG1_HTMCS13FBK FIELD32(0x00f00000) -#define HT_FBK_CFG1_HTMCS14FBK FIELD32(0x0f000000) -#define HT_FBK_CFG1_HTMCS15FBK FIELD32(0xf0000000) - -/* - * LG_FBK_CFG0: - */ -#define LG_FBK_CFG0 0x135c -#define LG_FBK_CFG0_OFDMMCS0FBK FIELD32(0x0000000f) -#define LG_FBK_CFG0_OFDMMCS1FBK FIELD32(0x000000f0) -#define LG_FBK_CFG0_OFDMMCS2FBK FIELD32(0x00000f00) -#define LG_FBK_CFG0_OFDMMCS3FBK FIELD32(0x0000f000) -#define LG_FBK_CFG0_OFDMMCS4FBK FIELD32(0x000f0000) -#define LG_FBK_CFG0_OFDMMCS5FBK FIELD32(0x00f00000) -#define LG_FBK_CFG0_OFDMMCS6FBK FIELD32(0x0f000000) -#define LG_FBK_CFG0_OFDMMCS7FBK FIELD32(0xf0000000) - -/* - * LG_FBK_CFG1: - */ -#define LG_FBK_CFG1 0x1360 -#define LG_FBK_CFG0_CCKMCS0FBK FIELD32(0x0000000f) -#define LG_FBK_CFG0_CCKMCS1FBK FIELD32(0x000000f0) -#define LG_FBK_CFG0_CCKMCS2FBK FIELD32(0x00000f00) -#define LG_FBK_CFG0_CCKMCS3FBK FIELD32(0x0000f000) - -/* - * CCK_PROT_CFG: CCK Protection - * PROTECT_RATE: Protection control frame rate for CCK TX(RTS/CTS/CFEnd) - * PROTECT_CTRL: Protection control frame type for CCK TX - * 0:none, 1:RTS/CTS, 2:CTS-to-self - * PROTECT_NAV: TXOP protection type for CCK TX - * 0:none, 1:ShortNAVprotect, 2:LongNAVProtect - * TX_OP_ALLOW_CCK: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_OFDM: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_MM20: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_MM40: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_GF20: CCK TXOP allowance, 0:disallow - * TX_OP_ALLOW_GF40: CCK TXOP allowance, 0:disallow - * RTS_TH_EN: RTS threshold enable on CCK TX - */ -#define CCK_PROT_CFG 0x1364 -#define CCK_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define CCK_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define CCK_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define CCK_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define CCK_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define CCK_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define CCK_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define CCK_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define CCK_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define CCK_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * OFDM_PROT_CFG: OFDM Protection - */ -#define OFDM_PROT_CFG 0x1368 -#define OFDM_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define OFDM_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define OFDM_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define OFDM_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define OFDM_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * MM20_PROT_CFG: MM20 Protection - */ -#define MM20_PROT_CFG 0x136c -#define MM20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define MM20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define MM20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define MM20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define MM20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define MM20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define MM20_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define MM20_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define MM20_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define MM20_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * MM40_PROT_CFG: MM40 Protection - */ -#define MM40_PROT_CFG 0x1370 -#define MM40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define MM40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define MM40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define MM40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define MM40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define MM40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define MM40_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define MM40_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define MM40_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define MM40_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * GF20_PROT_CFG: GF20 Protection - */ -#define GF20_PROT_CFG 0x1374 -#define GF20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define GF20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define GF20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define GF20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define GF20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define GF20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define GF20_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define GF20_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define GF20_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define GF20_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * GF40_PROT_CFG: GF40 Protection - */ -#define GF40_PROT_CFG 0x1378 -#define GF40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff) -#define GF40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000) -#define GF40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000) -#define GF40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000) -#define GF40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000) -#define GF40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000) -#define GF40_PROT_CFG_TX_OP_ALLOW_MM40 FIELD32(0x00800000) -#define GF40_PROT_CFG_TX_OP_ALLOW_GF20 FIELD32(0x01000000) -#define GF40_PROT_CFG_TX_OP_ALLOW_GF40 FIELD32(0x02000000) -#define GF40_PROT_CFG_RTS_TH_EN FIELD32(0x04000000) - -/* - * EXP_CTS_TIME: - */ -#define EXP_CTS_TIME 0x137c - -/* - * EXP_ACK_TIME: - */ -#define EXP_ACK_TIME 0x1380 - -/* - * RX_FILTER_CFG: RX configuration register. - */ -#define RX_FILTER_CFG 0x1400 -#define RX_FILTER_CFG_DROP_CRC_ERROR FIELD32(0x00000001) -#define RX_FILTER_CFG_DROP_PHY_ERROR FIELD32(0x00000002) -#define RX_FILTER_CFG_DROP_NOT_TO_ME FIELD32(0x00000004) -#define RX_FILTER_CFG_DROP_NOT_MY_BSSD FIELD32(0x00000008) -#define RX_FILTER_CFG_DROP_VER_ERROR FIELD32(0x00000010) -#define RX_FILTER_CFG_DROP_MULTICAST FIELD32(0x00000020) -#define RX_FILTER_CFG_DROP_BROADCAST FIELD32(0x00000040) -#define RX_FILTER_CFG_DROP_DUPLICATE FIELD32(0x00000080) -#define RX_FILTER_CFG_DROP_CF_END_ACK FIELD32(0x00000100) -#define RX_FILTER_CFG_DROP_CF_END FIELD32(0x00000200) -#define RX_FILTER_CFG_DROP_ACK FIELD32(0x00000400) -#define RX_FILTER_CFG_DROP_CTS FIELD32(0x00000800) -#define RX_FILTER_CFG_DROP_RTS FIELD32(0x00001000) -#define RX_FILTER_CFG_DROP_PSPOLL FIELD32(0x00002000) -#define RX_FILTER_CFG_DROP_BA FIELD32(0x00004000) -#define RX_FILTER_CFG_DROP_BAR FIELD32(0x00008000) -#define RX_FILTER_CFG_DROP_CNTL FIELD32(0x00010000) - -/* - * AUTO_RSP_CFG: - * AUTORESPONDER: 0: disable, 1: enable - * BAC_ACK_POLICY: 0:long, 1:short preamble - * CTS_40_MMODE: Response CTS 40MHz duplicate mode - * CTS_40_MREF: Response CTS 40MHz duplicate mode - * AR_PREAMBLE: Auto responder preamble 0:long, 1:short preamble - * DUAL_CTS_EN: Power bit value in control frame - * ACK_CTS_PSM_BIT:Power bit value in control frame - */ -#define AUTO_RSP_CFG 0x1404 -#define AUTO_RSP_CFG_AUTORESPONDER FIELD32(0x00000001) -#define AUTO_RSP_CFG_BAC_ACK_POLICY FIELD32(0x00000002) -#define AUTO_RSP_CFG_CTS_40_MMODE FIELD32(0x00000004) -#define AUTO_RSP_CFG_CTS_40_MREF FIELD32(0x00000008) -#define AUTO_RSP_CFG_AR_PREAMBLE FIELD32(0x00000010) -#define AUTO_RSP_CFG_DUAL_CTS_EN FIELD32(0x00000040) -#define AUTO_RSP_CFG_ACK_CTS_PSM_BIT FIELD32(0x00000080) - -/* - * LEGACY_BASIC_RATE: - */ -#define LEGACY_BASIC_RATE 0x1408 - -/* - * HT_BASIC_RATE: - */ -#define HT_BASIC_RATE 0x140c - -/* - * HT_CTRL_CFG: - */ -#define HT_CTRL_CFG 0x1410 - -/* - * SIFS_COST_CFG: - */ -#define SIFS_COST_CFG 0x1414 - -/* - * RX_PARSER_CFG: - * Set NAV for all received frames - */ -#define RX_PARSER_CFG 0x1418 - -/* - * TX_SEC_CNT0: - */ -#define TX_SEC_CNT0 0x1500 - -/* - * RX_SEC_CNT0: - */ -#define RX_SEC_CNT0 0x1504 - -/* - * CCMP_FC_MUTE: - */ -#define CCMP_FC_MUTE 0x1508 - -/* - * TXOP_HLDR_ADDR0: - */ -#define TXOP_HLDR_ADDR0 0x1600 - -/* - * TXOP_HLDR_ADDR1: - */ -#define TXOP_HLDR_ADDR1 0x1604 - -/* - * TXOP_HLDR_ET: - */ -#define TXOP_HLDR_ET 0x1608 - -/* - * QOS_CFPOLL_RA_DW0: - */ -#define QOS_CFPOLL_RA_DW0 0x160c - -/* - * QOS_CFPOLL_RA_DW1: - */ -#define QOS_CFPOLL_RA_DW1 0x1610 - -/* - * QOS_CFPOLL_QC: - */ -#define QOS_CFPOLL_QC 0x1614 - -/* - * RX_STA_CNT0: RX PLCP error count & RX CRC error count - */ -#define RX_STA_CNT0 0x1700 -#define RX_STA_CNT0_CRC_ERR FIELD32(0x0000ffff) -#define RX_STA_CNT0_PHY_ERR FIELD32(0xffff0000) - -/* - * RX_STA_CNT1: RX False CCA count & RX LONG frame count - */ -#define RX_STA_CNT1 0x1704 -#define RX_STA_CNT1_FALSE_CCA FIELD32(0x0000ffff) -#define RX_STA_CNT1_PLCP_ERR FIELD32(0xffff0000) - -/* - * RX_STA_CNT2: - */ -#define RX_STA_CNT2 0x1708 -#define RX_STA_CNT2_RX_DUPLI_COUNT FIELD32(0x0000ffff) -#define RX_STA_CNT2_RX_FIFO_OVERFLOW FIELD32(0xffff0000) - -/* - * TX_STA_CNT0: TX Beacon count - */ -#define TX_STA_CNT0 0x170c -#define TX_STA_CNT0_TX_FAIL_COUNT FIELD32(0x0000ffff) -#define TX_STA_CNT0_TX_BEACON_COUNT FIELD32(0xffff0000) - -/* - * TX_STA_CNT1: TX tx count - */ -#define TX_STA_CNT1 0x1710 -#define TX_STA_CNT1_TX_SUCCESS FIELD32(0x0000ffff) -#define TX_STA_CNT1_TX_RETRANSMIT FIELD32(0xffff0000) - -/* - * TX_STA_CNT2: TX tx count - */ -#define TX_STA_CNT2 0x1714 -#define TX_STA_CNT2_TX_ZERO_LEN_COUNT FIELD32(0x0000ffff) -#define TX_STA_CNT2_TX_UNDER_FLOW_COUNT FIELD32(0xffff0000) - -/* - * TX_STA_FIFO: TX Result for specific PID status fifo register - */ -#define TX_STA_FIFO 0x1718 -#define TX_STA_FIFO_VALID FIELD32(0x00000001) -#define TX_STA_FIFO_PID_TYPE FIELD32(0x0000001e) -#define TX_STA_FIFO_TX_SUCCESS FIELD32(0x00000020) -#define TX_STA_FIFO_TX_AGGRE FIELD32(0x00000040) -#define TX_STA_FIFO_TX_ACK_REQUIRED FIELD32(0x00000080) -#define TX_STA_FIFO_WCID FIELD32(0x0000ff00) -#define TX_STA_FIFO_SUCCESS_RATE FIELD32(0xffff0000) - -/* - * TX_AGG_CNT: Debug counter - */ -#define TX_AGG_CNT 0x171c -#define TX_AGG_CNT_NON_AGG_TX_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT_AGG_TX_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT0: - */ -#define TX_AGG_CNT0 0x1720 -#define TX_AGG_CNT0_AGG_SIZE_1_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT0_AGG_SIZE_2_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT1: - */ -#define TX_AGG_CNT1 0x1724 -#define TX_AGG_CNT1_AGG_SIZE_3_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT1_AGG_SIZE_4_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT2: - */ -#define TX_AGG_CNT2 0x1728 -#define TX_AGG_CNT2_AGG_SIZE_5_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT2_AGG_SIZE_6_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT3: - */ -#define TX_AGG_CNT3 0x172c -#define TX_AGG_CNT3_AGG_SIZE_7_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT3_AGG_SIZE_8_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT4: - */ -#define TX_AGG_CNT4 0x1730 -#define TX_AGG_CNT4_AGG_SIZE_9_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT4_AGG_SIZE_10_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT5: - */ -#define TX_AGG_CNT5 0x1734 -#define TX_AGG_CNT5_AGG_SIZE_11_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT5_AGG_SIZE_12_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT6: - */ -#define TX_AGG_CNT6 0x1738 -#define TX_AGG_CNT6_AGG_SIZE_13_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT6_AGG_SIZE_14_COUNT FIELD32(0xffff0000) - -/* - * TX_AGG_CNT7: - */ -#define TX_AGG_CNT7 0x173c -#define TX_AGG_CNT7_AGG_SIZE_15_COUNT FIELD32(0x0000ffff) -#define TX_AGG_CNT7_AGG_SIZE_16_COUNT FIELD32(0xffff0000) - -/* - * MPDU_DENSITY_CNT: - * TX_ZERO_DEL: TX zero length delimiter count - * RX_ZERO_DEL: RX zero length delimiter count - */ -#define MPDU_DENSITY_CNT 0x1740 -#define MPDU_DENSITY_CNT_TX_ZERO_DEL FIELD32(0x0000ffff) -#define MPDU_DENSITY_CNT_RX_ZERO_DEL FIELD32(0xffff0000) - -/* - * Security key table memory. - * MAC_WCID_BASE: 8-bytes (use only 6 bytes) * 256 entry - * PAIRWISE_KEY_TABLE_BASE: 32-byte * 256 entry - * MAC_IVEIV_TABLE_BASE: 8-byte * 256-entry - * MAC_WCID_ATTRIBUTE_BASE: 4-byte * 256-entry - * SHARED_KEY_TABLE_BASE: 32 bytes * 32-entry - * SHARED_KEY_MODE_BASE: 4 bits * 32-entry - */ -#define MAC_WCID_BASE 0x1800 -#define PAIRWISE_KEY_TABLE_BASE 0x4000 -#define MAC_IVEIV_TABLE_BASE 0x6000 -#define MAC_WCID_ATTRIBUTE_BASE 0x6800 -#define SHARED_KEY_TABLE_BASE 0x6c00 -#define SHARED_KEY_MODE_BASE 0x7000 - -#define MAC_WCID_ENTRY(__idx) \ - ( MAC_WCID_BASE + ((__idx) * sizeof(struct mac_wcid_entry)) ) -#define PAIRWISE_KEY_ENTRY(__idx) \ - ( PAIRWISE_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) ) -#define MAC_IVEIV_ENTRY(__idx) \ - ( MAC_IVEIV_TABLE_BASE + ((__idx) & sizeof(struct mac_iveiv_entry)) ) -#define MAC_WCID_ATTR_ENTRY(__idx) \ - ( MAC_WCID_ATTRIBUTE_BASE + ((__idx) * sizeof(u32)) ) -#define SHARED_KEY_ENTRY(__idx) \ - ( SHARED_KEY_TABLE_BASE + ((__idx) * sizeof(struct hw_key_entry)) ) -#define SHARED_KEY_MODE_ENTRY(__idx) \ - ( SHARED_KEY_MODE_BASE + ((__idx) * sizeof(u32)) ) - -struct mac_wcid_entry { - u8 mac[6]; - u8 reserved[2]; -} __attribute__ ((packed)); - -struct hw_key_entry { - u8 key[16]; - u8 tx_mic[8]; - u8 rx_mic[8]; -} __attribute__ ((packed)); - -struct mac_iveiv_entry { - u8 iv[8]; -} __attribute__ ((packed)); - -/* - * MAC_WCID_ATTRIBUTE: - */ -#define MAC_WCID_ATTRIBUTE_KEYTAB FIELD32(0x00000001) -#define MAC_WCID_ATTRIBUTE_CIPHER FIELD32(0x0000000e) -#define MAC_WCID_ATTRIBUTE_BSS_IDX FIELD32(0x00000070) -#define MAC_WCID_ATTRIBUTE_RX_WIUDF FIELD32(0x00000380) - -/* - * SHARED_KEY_MODE: - */ -#define SHARED_KEY_MODE_BSS0_KEY0 FIELD32(0x00000007) -#define SHARED_KEY_MODE_BSS0_KEY1 FIELD32(0x00000070) -#define SHARED_KEY_MODE_BSS0_KEY2 FIELD32(0x00000700) -#define SHARED_KEY_MODE_BSS0_KEY3 FIELD32(0x00007000) -#define SHARED_KEY_MODE_BSS1_KEY0 FIELD32(0x00070000) -#define SHARED_KEY_MODE_BSS1_KEY1 FIELD32(0x00700000) -#define SHARED_KEY_MODE_BSS1_KEY2 FIELD32(0x07000000) -#define SHARED_KEY_MODE_BSS1_KEY3 FIELD32(0x70000000) - -/* - * HOST-MCU communication - */ - -/* - * H2M_MAILBOX_CSR: Host-to-MCU Mailbox. - */ -#define H2M_MAILBOX_CSR 0x7010 -#define H2M_MAILBOX_CSR_ARG0 FIELD32(0x000000ff) -#define H2M_MAILBOX_CSR_ARG1 FIELD32(0x0000ff00) -#define H2M_MAILBOX_CSR_CMD_TOKEN FIELD32(0x00ff0000) -#define H2M_MAILBOX_CSR_OWNER FIELD32(0xff000000) - -/* - * H2M_MAILBOX_CID: - */ -#define H2M_MAILBOX_CID 0x7014 -#define H2M_MAILBOX_CID_CMD0 FIELD32(0x000000ff) -#define H2M_MAILBOX_CID_CMD1 FIELD32(0x0000ff00) -#define H2M_MAILBOX_CID_CMD2 FIELD32(0x00ff0000) -#define H2M_MAILBOX_CID_CMD3 FIELD32(0xff000000) - -/* - * H2M_MAILBOX_STATUS: - */ -#define H2M_MAILBOX_STATUS 0x701c - -/* - * H2M_INT_SRC: - */ -#define H2M_INT_SRC 0x7024 - -/* - * H2M_BBP_AGENT: - */ -#define H2M_BBP_AGENT 0x7028 - -/* - * MCU_LEDCS: LED control for MCU Mailbox. - */ -#define MCU_LEDCS_LED_MODE FIELD8(0x1f) -#define MCU_LEDCS_POLARITY FIELD8(0x01) - -/* - * HW_CS_CTS_BASE: - * Carrier-sense CTS frame base address. - * It's where mac stores carrier-sense frame for carrier-sense function. - */ -#define HW_CS_CTS_BASE 0x7700 - -/* - * HW_DFS_CTS_BASE: - * FS CTS frame base address. It's where mac stores CTS frame for DFS. - */ -#define HW_DFS_CTS_BASE 0x7780 - -/* - * TXRX control registers - base address 0x3000 - */ - -/* - * TXRX_CSR1: - * rt2860b UNKNOWN reg use R/O Reg Addr 0x77d0 first.. - */ -#define TXRX_CSR1 0x77d0 - -/* - * HW_DEBUG_SETTING_BASE: - * since NULL frame won't be that long (256 byte) - * We steal 16 tail bytes to save debugging settings - */ -#define HW_DEBUG_SETTING_BASE 0x77f0 -#define HW_DEBUG_SETTING_BASE2 0x7770 - -/* - * HW_BEACON_BASE - * In order to support maximum 8 MBSS and its maximum length - * is 512 bytes for each beacon - * Three section discontinue memory segments will be used. - * 1. The original region for BCN 0~3 - * 2. Extract memory from FCE table for BCN 4~5 - * 3. Extract memory from Pair-wise key table for BCN 6~7 - * It occupied those memory of wcid 238~253 for BCN 6 - * and wcid 222~237 for BCN 7 - * - * IMPORTANT NOTE: Not sure why legacy driver does this, - * but HW_BEACON_BASE7 is 0x0200 bytes below HW_BEACON_BASE6. - */ -#define HW_BEACON_BASE0 0x7800 -#define HW_BEACON_BASE1 0x7a00 -#define HW_BEACON_BASE2 0x7c00 -#define HW_BEACON_BASE3 0x7e00 -#define HW_BEACON_BASE4 0x7200 -#define HW_BEACON_BASE5 0x7400 -#define HW_BEACON_BASE6 0x5dc0 -#define HW_BEACON_BASE7 0x5bc0 - -#define HW_BEACON_OFFSET(__index) \ - ( ((__index) < 4) ? ( HW_BEACON_BASE0 + (__index * 0x0200) ) : \ - (((__index) < 6) ? ( HW_BEACON_BASE4 + ((__index - 4) * 0x0200) ) : \ - (HW_BEACON_BASE6 - ((__index - 6) * 0x0200))) ) - -/* * 8051 firmware image. */ #define FIRMWARE_RT2870 "rt2870.bin" #define FIRMWARE_IMAGE_BASE 0x3000 /* - * BBP registers. - * The wordsize of the BBP is 8 bits. - */ - -/* - * BBP 1: TX Antenna - */ -#define BBP1_TX_POWER FIELD8(0x07) -#define BBP1_TX_ANTENNA FIELD8(0x18) - -/* - * BBP 3: RX Antenna - */ -#define BBP3_RX_ANTENNA FIELD8(0x18) -#define BBP3_HT40_PLUS FIELD8(0x20) - -/* - * BBP 4: Bandwidth - */ -#define BBP4_TX_BF FIELD8(0x01) -#define BBP4_BANDWIDTH FIELD8(0x18) - -/* - * RFCSR registers - * The wordsize of the RFCSR is 8 bits. - */ - -/* - * RFCSR 6: - */ -#define RFCSR6_R FIELD8(0x03) - -/* - * RFCSR 7: - */ -#define RFCSR7_RF_TUNING FIELD8(0x01) - -/* - * RFCSR 12: - */ -#define RFCSR12_TX_POWER FIELD8(0x1f) - -/* - * RFCSR 22: - */ -#define RFCSR22_BASEBAND_LOOPBACK FIELD8(0x01) - -/* - * RFCSR 23: - */ -#define RFCSR23_FREQ_OFFSET FIELD8(0x7f) - -/* - * RFCSR 30: - */ -#define RFCSR30_RF_CALIBRATION FIELD8(0x80) - -/* - * RF registers - */ - -/* - * RF 2 - */ -#define RF2_ANTENNA_RX2 FIELD32(0x00000040) -#define RF2_ANTENNA_TX1 FIELD32(0x00004000) -#define RF2_ANTENNA_RX1 FIELD32(0x00020000) - -/* - * RF 3 - */ -#define RF3_TXPOWER_G FIELD32(0x00003e00) -#define RF3_TXPOWER_A_7DBM_BOOST FIELD32(0x00000200) -#define RF3_TXPOWER_A FIELD32(0x00003c00) - -/* - * RF 4 - */ -#define RF4_TXPOWER_G FIELD32(0x000007c0) -#define RF4_TXPOWER_A_7DBM_BOOST FIELD32(0x00000040) -#define RF4_TXPOWER_A FIELD32(0x00000780) -#define RF4_FREQ_OFFSET FIELD32(0x001f8000) -#define RF4_HT40 FIELD32(0x00200000) - -/* - * EEPROM content. - * The wordsize of the EEPROM is 16 bits. - */ - -/* - * EEPROM Version - */ -#define EEPROM_VERSION 0x0001 -#define EEPROM_VERSION_FAE FIELD16(0x00ff) -#define EEPROM_VERSION_VERSION FIELD16(0xff00) - -/* - * HW MAC address. - */ -#define EEPROM_MAC_ADDR_0 0x0002 -#define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) -#define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) -#define EEPROM_MAC_ADDR_1 0x0003 -#define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) -#define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) -#define EEPROM_MAC_ADDR_2 0x0004 -#define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) -#define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) - -/* - * EEPROM ANTENNA config - * RXPATH: 1: 1R, 2: 2R, 3: 3R - * TXPATH: 1: 1T, 2: 2T - */ -#define EEPROM_ANTENNA 0x001a -#define EEPROM_ANTENNA_RXPATH FIELD16(0x000f) -#define EEPROM_ANTENNA_TXPATH FIELD16(0x00f0) -#define EEPROM_ANTENNA_RF_TYPE FIELD16(0x0f00) - -/* - * EEPROM NIC config - * CARDBUS_ACCEL: 0 - enable, 1 - disable - */ -#define EEPROM_NIC 0x001b -#define EEPROM_NIC_HW_RADIO FIELD16(0x0001) -#define EEPROM_NIC_DYNAMIC_TX_AGC FIELD16(0x0002) -#define EEPROM_NIC_EXTERNAL_LNA_BG FIELD16(0x0004) -#define EEPROM_NIC_EXTERNAL_LNA_A FIELD16(0x0008) -#define EEPROM_NIC_CARDBUS_ACCEL FIELD16(0x0010) -#define EEPROM_NIC_BW40M_SB_BG FIELD16(0x0020) -#define EEPROM_NIC_BW40M_SB_A FIELD16(0x0040) -#define EEPROM_NIC_WPS_PBC FIELD16(0x0080) -#define EEPROM_NIC_BW40M_BG FIELD16(0x0100) -#define EEPROM_NIC_BW40M_A FIELD16(0x0200) - -/* - * EEPROM frequency - */ -#define EEPROM_FREQ 0x001d -#define EEPROM_FREQ_OFFSET FIELD16(0x00ff) -#define EEPROM_FREQ_LED_MODE FIELD16(0x7f00) -#define EEPROM_FREQ_LED_POLARITY FIELD16(0x1000) - -/* - * EEPROM LED - * POLARITY_RDY_G: Polarity RDY_G setting. - * POLARITY_RDY_A: Polarity RDY_A setting. - * POLARITY_ACT: Polarity ACT setting. - * POLARITY_GPIO_0: Polarity GPIO0 setting. - * POLARITY_GPIO_1: Polarity GPIO1 setting. - * POLARITY_GPIO_2: Polarity GPIO2 setting. - * POLARITY_GPIO_3: Polarity GPIO3 setting. - * POLARITY_GPIO_4: Polarity GPIO4 setting. - * LED_MODE: Led mode. - */ -#define EEPROM_LED1 0x001e -#define EEPROM_LED2 0x001f -#define EEPROM_LED3 0x0020 -#define EEPROM_LED_POLARITY_RDY_BG FIELD16(0x0001) -#define EEPROM_LED_POLARITY_RDY_A FIELD16(0x0002) -#define EEPROM_LED_POLARITY_ACT FIELD16(0x0004) -#define EEPROM_LED_POLARITY_GPIO_0 FIELD16(0x0008) -#define EEPROM_LED_POLARITY_GPIO_1 FIELD16(0x0010) -#define EEPROM_LED_POLARITY_GPIO_2 FIELD16(0x0020) -#define EEPROM_LED_POLARITY_GPIO_3 FIELD16(0x0040) -#define EEPROM_LED_POLARITY_GPIO_4 FIELD16(0x0080) -#define EEPROM_LED_LED_MODE FIELD16(0x1f00) - -/* - * EEPROM LNA - */ -#define EEPROM_LNA 0x0022 -#define EEPROM_LNA_BG FIELD16(0x00ff) -#define EEPROM_LNA_A0 FIELD16(0xff00) - -/* - * EEPROM RSSI BG offset - */ -#define EEPROM_RSSI_BG 0x0023 -#define EEPROM_RSSI_BG_OFFSET0 FIELD16(0x00ff) -#define EEPROM_RSSI_BG_OFFSET1 FIELD16(0xff00) - -/* - * EEPROM RSSI BG2 offset - */ -#define EEPROM_RSSI_BG2 0x0024 -#define EEPROM_RSSI_BG2_OFFSET2 FIELD16(0x00ff) -#define EEPROM_RSSI_BG2_LNA_A1 FIELD16(0xff00) - -/* - * EEPROM RSSI A offset - */ -#define EEPROM_RSSI_A 0x0025 -#define EEPROM_RSSI_A_OFFSET0 FIELD16(0x00ff) -#define EEPROM_RSSI_A_OFFSET1 FIELD16(0xff00) - -/* - * EEPROM RSSI A2 offset - */ -#define EEPROM_RSSI_A2 0x0026 -#define EEPROM_RSSI_A2_OFFSET2 FIELD16(0x00ff) -#define EEPROM_RSSI_A2_LNA_A2 FIELD16(0xff00) - -/* - * EEPROM TXpower delta: 20MHZ AND 40 MHZ use different power. - * This is delta in 40MHZ. - * VALUE: Tx Power dalta value (MAX=4) - * TYPE: 1: Plus the delta value, 0: minus the delta value - * TXPOWER: Enable: - */ -#define EEPROM_TXPOWER_DELTA 0x0028 -#define EEPROM_TXPOWER_DELTA_VALUE FIELD16(0x003f) -#define EEPROM_TXPOWER_DELTA_TYPE FIELD16(0x0040) -#define EEPROM_TXPOWER_DELTA_TXPOWER FIELD16(0x0080) - -/* - * EEPROM TXPOWER 802.11BG - */ -#define EEPROM_TXPOWER_BG1 0x0029 -#define EEPROM_TXPOWER_BG2 0x0030 -#define EEPROM_TXPOWER_BG_SIZE 7 -#define EEPROM_TXPOWER_BG_1 FIELD16(0x00ff) -#define EEPROM_TXPOWER_BG_2 FIELD16(0xff00) - -/* - * EEPROM TXPOWER 802.11A - */ -#define EEPROM_TXPOWER_A1 0x003c -#define EEPROM_TXPOWER_A2 0x0053 -#define EEPROM_TXPOWER_A_SIZE 6 -#define EEPROM_TXPOWER_A_1 FIELD16(0x00ff) -#define EEPROM_TXPOWER_A_2 FIELD16(0xff00) - -/* - * EEPROM TXpower byrate: 20MHZ power - */ -#define EEPROM_TXPOWER_BYRATE 0x006f - -/* - * EEPROM BBP. - */ -#define EEPROM_BBP_START 0x0078 -#define EEPROM_BBP_SIZE 16 -#define EEPROM_BBP_VALUE FIELD16(0x00ff) -#define EEPROM_BBP_REG_ID FIELD16(0xff00) - -/* - * MCU mailbox commands. - */ -#define MCU_SLEEP 0x30 -#define MCU_WAKEUP 0x31 -#define MCU_RADIO_OFF 0x35 -#define MCU_CURRENT 0x36 -#define MCU_LED 0x50 -#define MCU_LED_STRENGTH 0x51 -#define MCU_LED_1 0x52 -#define MCU_LED_2 0x53 -#define MCU_LED_3 0x54 -#define MCU_RADAR 0x60 -#define MCU_BOOT_SIGNAL 0x72 -#define MCU_BBP_SIGNAL 0x80 -#define MCU_POWER_SAVE 0x83 - -/* - * MCU mailbox tokens - */ -#define TOKEN_WAKUP 3 - -/* * DMA descriptor defines. */ -#define TXD_DESC_SIZE ( 4 * sizeof(__le32) ) #define TXINFO_DESC_SIZE ( 1 * sizeof(__le32) ) -#define TXWI_DESC_SIZE ( 4 * sizeof(__le32) ) -#define RXD_DESC_SIZE ( 1 * sizeof(__le32) ) -#define RXWI_DESC_SIZE ( 4 * sizeof(__le32) ) - -/* - * TX descriptor format for TX, PRIO and Beacon Ring. - */ - -/* - * Word0 - */ -#define TXD_W0_SD_PTR0 FIELD32(0xffffffff) - -/* - * Word1 - */ -#define TXD_W1_SD_LEN1 FIELD32(0x00003fff) -#define TXD_W1_LAST_SEC1 FIELD32(0x00004000) -#define TXD_W1_BURST FIELD32(0x00008000) -#define TXD_W1_SD_LEN0 FIELD32(0x3fff0000) -#define TXD_W1_LAST_SEC0 FIELD32(0x40000000) -#define TXD_W1_DMA_DONE FIELD32(0x80000000) - -/* - * Word2 - */ -#define TXD_W2_SD_PTR1 FIELD32(0xffffffff) - -/* - * Word3 - * WIV: Wireless Info Valid. 1: Driver filled WI, 0: DMA needs to copy WI - * QSEL: Select on-chip FIFO ID for 2nd-stage output scheduler. - * 0:MGMT, 1:HCCA 2:EDCA - */ -#define TXD_W3_WIV FIELD32(0x01000000) -#define TXD_W3_QSEL FIELD32(0x06000000) -#define TXD_W3_TCO FIELD32(0x20000000) -#define TXD_W3_UCO FIELD32(0x40000000) -#define TXD_W3_ICO FIELD32(0x80000000) +#define RXINFO_DESC_SIZE ( 1 * sizeof(__le32) ) /* * TX Info structure @@ -1807,52 +97,6 @@ struct mac_iveiv_entry { #define TXINFO_W0_USB_DMA_TX_BURST FIELD32(0x80000000) /* - * TX WI structure - */ - -/* - * Word0 - * FRAG: 1 To inform TKIP engine this is a fragment. - * MIMO_PS: The remote peer is in dynamic MIMO-PS mode - * TX_OP: 0:HT TXOP rule , 1:PIFS TX ,2:Backoff, 3:sifs - * BW: Channel bandwidth 20MHz or 40 MHz - * STBC: 1: STBC support MCS =0-7, 2,3 : RESERVED - */ -#define TXWI_W0_FRAG FIELD32(0x00000001) -#define TXWI_W0_MIMO_PS FIELD32(0x00000002) -#define TXWI_W0_CF_ACK FIELD32(0x00000004) -#define TXWI_W0_TS FIELD32(0x00000008) -#define TXWI_W0_AMPDU FIELD32(0x00000010) -#define TXWI_W0_MPDU_DENSITY FIELD32(0x000000e0) -#define TXWI_W0_TX_OP FIELD32(0x00000300) -#define TXWI_W0_MCS FIELD32(0x007f0000) -#define TXWI_W0_BW FIELD32(0x00800000) -#define TXWI_W0_SHORT_GI FIELD32(0x01000000) -#define TXWI_W0_STBC FIELD32(0x06000000) -#define TXWI_W0_IFS FIELD32(0x08000000) -#define TXWI_W0_PHYMODE FIELD32(0xc0000000) - -/* - * Word1 - */ -#define TXWI_W1_ACK FIELD32(0x00000001) -#define TXWI_W1_NSEQ FIELD32(0x00000002) -#define TXWI_W1_BW_WIN_SIZE FIELD32(0x000000fc) -#define TXWI_W1_WIRELESS_CLI_ID FIELD32(0x0000ff00) -#define TXWI_W1_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) -#define TXWI_W1_PACKETID FIELD32(0xf0000000) - -/* - * Word2 - */ -#define TXWI_W2_IV FIELD32(0xffffffff) - -/* - * Word3 - */ -#define TXWI_W3_EIV FIELD32(0xffffffff) - -/* * RX descriptor format for RX Ring. */ @@ -1888,64 +132,4 @@ struct mac_iveiv_entry { #define RXD_W0_LAST_AMSDU FIELD32(0x00080000) #define RXD_W0_PLCP_SIGNAL FIELD32(0xfff00000) -/* - * RX WI structure - */ - -/* - * Word0 - */ -#define RXWI_W0_WIRELESS_CLI_ID FIELD32(0x000000ff) -#define RXWI_W0_KEY_INDEX FIELD32(0x00000300) -#define RXWI_W0_BSSID FIELD32(0x00001c00) -#define RXWI_W0_UDF FIELD32(0x0000e000) -#define RXWI_W0_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) -#define RXWI_W0_TID FIELD32(0xf0000000) - -/* - * Word1 - */ -#define RXWI_W1_FRAG FIELD32(0x0000000f) -#define RXWI_W1_SEQUENCE FIELD32(0x0000fff0) -#define RXWI_W1_MCS FIELD32(0x007f0000) -#define RXWI_W1_BW FIELD32(0x00800000) -#define RXWI_W1_SHORT_GI FIELD32(0x01000000) -#define RXWI_W1_STBC FIELD32(0x06000000) -#define RXWI_W1_PHYMODE FIELD32(0xc0000000) - -/* - * Word2 - */ -#define RXWI_W2_RSSI0 FIELD32(0x000000ff) -#define RXWI_W2_RSSI1 FIELD32(0x0000ff00) -#define RXWI_W2_RSSI2 FIELD32(0x00ff0000) - -/* - * Word3 - */ -#define RXWI_W3_SNR0 FIELD32(0x000000ff) -#define RXWI_W3_SNR1 FIELD32(0x0000ff00) - -/* - * Macros for converting txpower from EEPROM to mac80211 value - * and from mac80211 value to register value. - */ -#define MIN_G_TXPOWER 0 -#define MIN_A_TXPOWER -7 -#define MAX_G_TXPOWER 31 -#define MAX_A_TXPOWER 15 -#define DEFAULT_TXPOWER 5 - -#define TXPOWER_G_FROM_DEV(__txpower) \ - ((__txpower) > MAX_G_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) - -#define TXPOWER_G_TO_DEV(__txpower) \ - clamp_t(char, __txpower, MIN_G_TXPOWER, MAX_G_TXPOWER) - -#define TXPOWER_A_FROM_DEV(__txpower) \ - ((__txpower) > MAX_A_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) - -#define TXPOWER_A_TO_DEV(__txpower) \ - clamp_t(char, __txpower, MIN_A_TXPOWER, MAX_A_TXPOWER) - #endif /* RT2800USB_H */ diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h index 196de8a..c83dbae 100644 --- a/drivers/net/wireless/rt2x00/rt2x00.h +++ b/drivers/net/wireless/rt2x00/rt2x00.h @@ -144,6 +144,11 @@ struct avg_val { int avg_weight; }; +enum rt2x00_chip_intf { + RT2X00_CHIP_INTF_PCI, + RT2X00_CHIP_INTF_USB, +}; + /* * Chipset identification * The chipset on the device is composed of a RT and RF chip. @@ -169,6 +174,8 @@ struct rt2x00_chip { u16 rf; u32 rev; + + enum rt2x00_chip_intf intf; }; /* @@ -842,9 +849,23 @@ struct rt2x00_dev { * Firmware image. */ const struct firmware *fw; + + /* + * Driver specific data. + */ + void *priv; }; /* + * Register defines. + * Some registers require multiple attempts before success, + * in those cases REGISTER_BUSY_COUNT attempts should be + * taken with a REGISTER_BUSY_DELAY interval. + */ +#define REGISTER_BUSY_COUNT 5 +#define REGISTER_BUSY_DELAY 100 + +/* * Generic RF access. * The RF is being accessed by word index. */ @@ -932,6 +953,28 @@ static inline bool rt2x00_check_rev(const struct rt2x00_chip *chipset, return ((chipset->rev & mask) == rev); } +static inline void rt2x00_set_chip_intf(struct rt2x00_dev *rt2x00dev, + enum rt2x00_chip_intf intf) +{ + rt2x00dev->chip.intf = intf; +} + +static inline bool rt2x00_intf(const struct rt2x00_chip *chipset, + enum rt2x00_chip_intf intf) +{ + return (chipset->intf == intf); +} + +static inline bool rt2x00_intf_is_pci(struct rt2x00_dev *rt2x00dev) +{ + return rt2x00_intf(&rt2x00dev->chip, RT2X00_CHIP_INTF_PCI); +} + +static inline bool rt2x00_intf_is_usb(struct rt2x00_dev *rt2x00dev) +{ + return rt2x00_intf(&rt2x00dev->chip, RT2X00_CHIP_INTF_USB); +} + /** * rt2x00queue_map_txskb - Map a skb into DMA for TX purposes. * @rt2x00dev: Pointer to &struct rt2x00_dev. diff --git a/drivers/net/wireless/rt2x00/rt2x00leds.h b/drivers/net/wireless/rt2x00/rt2x00leds.h index 1046977..8e03c04 100644 --- a/drivers/net/wireless/rt2x00/rt2x00leds.h +++ b/drivers/net/wireless/rt2x00/rt2x00leds.h @@ -33,8 +33,6 @@ enum led_type { LED_TYPE_QUALITY, }; -#ifdef CONFIG_RT2X00_LIB_LEDS - struct rt2x00_led { struct rt2x00_dev *rt2x00dev; struct led_classdev led_dev; @@ -45,6 +43,4 @@ struct rt2x00_led { #define LED_REGISTERED ( 1 << 1 ) }; -#endif /* CONFIG_RT2X00_LIB_LEDS */ - #endif /* RT2X00LEDS_H */ diff --git a/drivers/net/wireless/rt2x00/rt2x00pci.h b/drivers/net/wireless/rt2x00/rt2x00pci.h index 15a1248..ae33eeb 100644 --- a/drivers/net/wireless/rt2x00/rt2x00pci.h +++ b/drivers/net/wireless/rt2x00/rt2x00pci.h @@ -35,15 +35,6 @@ #define PCI_DEVICE_DATA(__ops) .driver_data = (kernel_ulong_t)(__ops) /* - * Register defines. - * Some registers require multiple attempts before success, - * in those cases REGISTER_BUSY_COUNT attempts should be - * taken with a REGISTER_BUSY_DELAY interval. - */ -#define REGISTER_BUSY_COUNT 5 -#define REGISTER_BUSY_DELAY 100 - -/* * Register access. */ static inline void rt2x00pci_register_read(struct rt2x00_dev *rt2x00dev, @@ -53,10 +44,9 @@ static inline void rt2x00pci_register_read(struct rt2x00_dev *rt2x00dev, *value = readl(rt2x00dev->csr.base + offset); } -static inline void -rt2x00pci_register_multiread(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - void *value, const u16 length) +static inline void rt2x00pci_register_multiread(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + void *value, const u32 length) { memcpy_fromio(value, rt2x00dev->csr.base + offset, length); } @@ -68,10 +58,10 @@ static inline void rt2x00pci_register_write(struct rt2x00_dev *rt2x00dev, writel(value, rt2x00dev->csr.base + offset); } -static inline void -rt2x00pci_register_multiwrite(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - const void *value, const u16 length) +static inline void rt2x00pci_register_multiwrite(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const void *value, + const u32 length) { memcpy_toio(rt2x00dev->csr.base + offset, value, length); } diff --git a/drivers/net/wireless/rt2x00/rt2x00usb.c b/drivers/net/wireless/rt2x00/rt2x00usb.c index f02b48a..c9cbdaa 100644 --- a/drivers/net/wireless/rt2x00/rt2x00usb.c +++ b/drivers/net/wireless/rt2x00/rt2x00usb.c @@ -160,7 +160,7 @@ EXPORT_SYMBOL_GPL(rt2x00usb_vendor_request_large_buff); int rt2x00usb_regbusy_read(struct rt2x00_dev *rt2x00dev, const unsigned int offset, - struct rt2x00_field32 field, + const struct rt2x00_field32 field, u32 *reg) { unsigned int i; diff --git a/drivers/net/wireless/rt2x00/rt2x00usb.h b/drivers/net/wireless/rt2x00/rt2x00usb.h index bd2d59c..9943e42 100644 --- a/drivers/net/wireless/rt2x00/rt2x00usb.h +++ b/drivers/net/wireless/rt2x00/rt2x00usb.h @@ -39,17 +39,11 @@ #define USB_DEVICE_DATA(__ops) .driver_info = (kernel_ulong_t)(__ops) /* - * Register defines. - * Some registers require multiple attempts before success, - * in those cases REGISTER_BUSY_COUNT attempts should be - * taken with a REGISTER_BUSY_DELAY interval. * For USB vendor requests we need to pass a timeout * time in ms, for this we use the REGISTER_TIMEOUT, * however when loading firmware a higher value is * required. In that case we use the REGISTER_TIMEOUT_FIRMWARE. */ -#define REGISTER_BUSY_COUNT 5 -#define REGISTER_BUSY_DELAY 100 #define REGISTER_TIMEOUT 500 #define REGISTER_TIMEOUT_FIRMWARE 1000 @@ -232,7 +226,7 @@ static inline int rt2x00usb_eeprom_read(struct rt2x00_dev *rt2x00dev, } /** - * rt2x00usb_regbusy_read - Read 32bit register word + * rt2x00usb_register_read - Read 32bit register word * @rt2x00dev: Device pointer, see &struct rt2x00_dev. * @offset: Register offset * @value: Pointer to where register contents should be stored @@ -340,12 +334,13 @@ static inline void rt2x00usb_register_write_lock(struct rt2x00_dev *rt2x00dev, * through rt2x00usb_vendor_request_buff(). */ static inline void rt2x00usb_register_multiwrite(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - void *value, const u32 length) + const unsigned int offset, + const void *value, + const u32 length) { rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE, USB_VENDOR_REQUEST_OUT, offset, - value, length, + (void *)value, length, REGISTER_TIMEOUT32(length)); } @@ -364,7 +359,7 @@ static inline void rt2x00usb_register_multiwrite(struct rt2x00_dev *rt2x00dev, */ int rt2x00usb_regbusy_read(struct rt2x00_dev *rt2x00dev, const unsigned int offset, - struct rt2x00_field32 field, + const struct rt2x00_field32 field, u32 *reg); /* diff --git a/drivers/net/wireless/rtl818x/rtl8187.h b/drivers/net/wireless/rtl818x/rtl8187.h index bf9175a..abb4907 100644 --- a/drivers/net/wireless/rtl818x/rtl8187.h +++ b/drivers/net/wireless/rtl818x/rtl8187.h @@ -119,7 +119,6 @@ struct rtl8187_priv { } hw_rev; struct sk_buff_head rx_queue; u8 signal; - u8 quality; u8 noise; u8 slot_time; u8 aifsn[4]; diff --git a/drivers/net/wireless/rtl818x/rtl8187_dev.c b/drivers/net/wireless/rtl818x/rtl8187_dev.c index 2017ccc..76973b8 100644 --- a/drivers/net/wireless/rtl818x/rtl8187_dev.c +++ b/drivers/net/wireless/rtl818x/rtl8187_dev.c @@ -320,7 +320,6 @@ static void rtl8187_rx_cb(struct urb *urb) struct ieee80211_rx_status rx_status = { 0 }; int rate, signal; u32 flags; - u32 quality; unsigned long f; spin_lock_irqsave(&priv->rx_queue.lock, f); @@ -338,10 +337,9 @@ static void rtl8187_rx_cb(struct urb *urb) (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr)); flags = le32_to_cpu(hdr->flags); /* As with the RTL8187B below, the AGC is used to calculate - * signal strength and quality. In this case, the scaling + * signal strength. In this case, the scaling * constants are derived from the output of p54usb. */ - quality = 130 - ((41 * hdr->agc) >> 6); signal = -4 - ((27 * hdr->agc) >> 6); rx_status.antenna = (hdr->signal >> 7) & 1; rx_status.mactime = le64_to_cpu(hdr->mac_time); @@ -354,23 +352,18 @@ static void rtl8187_rx_cb(struct urb *urb) * In testing, none of these quantities show qualitative * agreement with AP signal strength, except for the AGC, * which is inversely proportional to the strength of the - * signal. In the following, the quality and signal strength - * are derived from the AGC. The arbitrary scaling constants + * signal. In the following, the signal strength + * is derived from the AGC. The arbitrary scaling constants * are chosen to make the results close to the values obtained * for a BCM4312 using b43 as the driver. The noise is ignored * for now. */ flags = le32_to_cpu(hdr->flags); - quality = 170 - hdr->agc; signal = 14 - hdr->agc / 2; rx_status.antenna = (hdr->rssi >> 7) & 1; rx_status.mactime = le64_to_cpu(hdr->mac_time); } - if (quality > 100) - quality = 100; - rx_status.qual = quality; - priv->quality = quality; rx_status.signal = signal; priv->signal = signal; rate = (flags >> 20) & 0xF; diff --git a/drivers/net/wireless/strip.c b/drivers/net/wireless/strip.c deleted file mode 100644 index 698aade..0000000 --- a/drivers/net/wireless/strip.c +++ /dev/null @@ -1,2822 +0,0 @@ -/* - * Copyright 1996 The Board of Trustees of The Leland Stanford - * Junior University. All Rights Reserved. - * - * Permission to use, copy, modify, and distribute this - * software and its documentation for any purpose and without - * fee is hereby granted, provided that the above copyright - * notice appear in all copies. Stanford University - * makes no representations about the suitability of this - * software for any purpose. It is provided "as is" without - * express or implied warranty. - * - * strip.c This module implements Starmode Radio IP (STRIP) - * for kernel-based devices like TTY. It interfaces between a - * raw TTY, and the kernel's INET protocol layers (via DDI). - * - * Version: @(#)strip.c 1.3 July 1997 - * - * Author: Stuart Cheshire <cheshire@cs.stanford.edu> - * - * Fixes: v0.9 12th Feb 1996 (SC) - * New byte stuffing (2+6 run-length encoding) - * New watchdog timer task - * New Protocol key (SIP0) - * - * v0.9.1 3rd March 1996 (SC) - * Changed to dynamic device allocation -- no more compile - * time (or boot time) limit on the number of STRIP devices. - * - * v0.9.2 13th March 1996 (SC) - * Uses arp cache lookups (but doesn't send arp packets yet) - * - * v0.9.3 17th April 1996 (SC) - * Fixed bug where STR_ERROR flag was getting set unneccessarily - * (causing otherwise good packets to be unneccessarily dropped) - * - * v0.9.4 27th April 1996 (SC) - * First attempt at using "&COMMAND" Starmode AT commands - * - * v0.9.5 29th May 1996 (SC) - * First attempt at sending (unicast) ARP packets - * - * v0.9.6 5th June 1996 (Elliot) - * Put "message level" tags in every "printk" statement - * - * v0.9.7 13th June 1996 (laik) - * Added support for the /proc fs - * - * v0.9.8 July 1996 (Mema) - * Added packet logging - * - * v1.0 November 1996 (SC) - * Fixed (severe) memory leaks in the /proc fs code - * Fixed race conditions in the logging code - * - * v1.1 January 1997 (SC) - * Deleted packet logging (use tcpdump instead) - * Added support for Metricom Firmware v204 features - * (like message checksums) - * - * v1.2 January 1997 (SC) - * Put portables list back in - * - * v1.3 July 1997 (SC) - * Made STRIP driver set the radio's baud rate automatically. - * It is no longer necessarily to manually set the radio's - * rate permanently to 115200 -- the driver handles setting - * the rate automatically. - */ - -#ifdef MODULE -static const char StripVersion[] = "1.3A-STUART.CHESHIRE-MODULAR"; -#else -static const char StripVersion[] = "1.3A-STUART.CHESHIRE"; -#endif - -#define TICKLE_TIMERS 0 -#define EXT_COUNTERS 1 - - -/************************************************************************/ -/* Header files */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/bitops.h> -#include <asm/system.h> -#include <asm/uaccess.h> - -# include <linux/ctype.h> -#include <linux/string.h> -#include <linux/mm.h> -#include <linux/interrupt.h> -#include <linux/in.h> -#include <linux/tty.h> -#include <linux/errno.h> -#include <linux/netdevice.h> -#include <linux/inetdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/if_arp.h> -#include <linux/if_strip.h> -#include <linux/proc_fs.h> -#include <linux/seq_file.h> -#include <linux/serial.h> -#include <linux/serialP.h> -#include <linux/rcupdate.h> -#include <linux/compat.h> -#include <net/arp.h> -#include <net/net_namespace.h> - -#include <linux/ip.h> -#include <linux/tcp.h> -#include <linux/time.h> -#include <linux/jiffies.h> - -/************************************************************************/ -/* Useful structures and definitions */ - -/* - * A MetricomKey identifies the protocol being carried inside a Metricom - * Starmode packet. - */ - -typedef union { - __u8 c[4]; - __u32 l; -} MetricomKey; - -/* - * An IP address can be viewed as four bytes in memory (which is what it is) or as - * a single 32-bit long (which is convenient for assignment, equality testing etc.) - */ - -typedef union { - __u8 b[4]; - __u32 l; -} IPaddr; - -/* - * A MetricomAddressString is used to hold a printable representation of - * a Metricom address. - */ - -typedef struct { - __u8 c[24]; -} MetricomAddressString; - -/* Encapsulation can expand packet of size x to 65/64x + 1 - * Sent packet looks like "<CR>*<address>*<key><encaps payload><CR>" - * 1 1 1-18 1 4 ? 1 - * eg. <CR>*0000-1234*SIP0<encaps payload><CR> - * We allow 31 bytes for the stars, the key, the address and the <CR>s - */ -#define STRIP_ENCAP_SIZE(X) (32 + (X)*65L/64L) - -/* - * A STRIP_Header is never really sent over the radio, but making a dummy - * header for internal use within the kernel that looks like an Ethernet - * header makes certain other software happier. For example, tcpdump - * already understands Ethernet headers. - */ - -typedef struct { - MetricomAddress dst_addr; /* Destination address, e.g. "0000-1234" */ - MetricomAddress src_addr; /* Source address, e.g. "0000-5678" */ - unsigned short protocol; /* The protocol type, using Ethernet codes */ -} STRIP_Header; - -typedef struct { - char c[60]; -} MetricomNode; - -#define NODE_TABLE_SIZE 32 -typedef struct { - struct timeval timestamp; - int num_nodes; - MetricomNode node[NODE_TABLE_SIZE]; -} MetricomNodeTable; - -enum { FALSE = 0, TRUE = 1 }; - -/* - * Holds the radio's firmware version. - */ -typedef struct { - char c[50]; -} FirmwareVersion; - -/* - * Holds the radio's serial number. - */ -typedef struct { - char c[18]; -} SerialNumber; - -/* - * Holds the radio's battery voltage. - */ -typedef struct { - char c[11]; -} BatteryVoltage; - -typedef struct { - char c[8]; -} char8; - -enum { - NoStructure = 0, /* Really old firmware */ - StructuredMessages = 1, /* Parsable AT response msgs */ - ChecksummedMessages = 2 /* Parsable AT response msgs with checksums */ -}; - -struct strip { - int magic; - /* - * These are pointers to the malloc()ed frame buffers. - */ - - unsigned char *rx_buff; /* buffer for received IP packet */ - unsigned char *sx_buff; /* buffer for received serial data */ - int sx_count; /* received serial data counter */ - int sx_size; /* Serial buffer size */ - unsigned char *tx_buff; /* transmitter buffer */ - unsigned char *tx_head; /* pointer to next byte to XMIT */ - int tx_left; /* bytes left in XMIT queue */ - int tx_size; /* Serial buffer size */ - - /* - * STRIP interface statistics. - */ - - unsigned long rx_packets; /* inbound frames counter */ - unsigned long tx_packets; /* outbound frames counter */ - unsigned long rx_errors; /* Parity, etc. errors */ - unsigned long tx_errors; /* Planned stuff */ - unsigned long rx_dropped; /* No memory for skb */ - unsigned long tx_dropped; /* When MTU change */ - unsigned long rx_over_errors; /* Frame bigger than STRIP buf. */ - - unsigned long pps_timer; /* Timer to determine pps */ - unsigned long rx_pps_count; /* Counter to determine pps */ - unsigned long tx_pps_count; /* Counter to determine pps */ - unsigned long sx_pps_count; /* Counter to determine pps */ - unsigned long rx_average_pps; /* rx packets per second * 8 */ - unsigned long tx_average_pps; /* tx packets per second * 8 */ - unsigned long sx_average_pps; /* sent packets per second * 8 */ - -#ifdef EXT_COUNTERS - unsigned long rx_bytes; /* total received bytes */ - unsigned long tx_bytes; /* total received bytes */ - unsigned long rx_rbytes; /* bytes thru radio i/f */ - unsigned long tx_rbytes; /* bytes thru radio i/f */ - unsigned long rx_sbytes; /* tot bytes thru serial i/f */ - unsigned long tx_sbytes; /* tot bytes thru serial i/f */ - unsigned long rx_ebytes; /* tot stat/err bytes */ - unsigned long tx_ebytes; /* tot stat/err bytes */ -#endif - - /* - * Internal variables. - */ - - struct list_head list; /* Linked list of devices */ - - int discard; /* Set if serial error */ - int working; /* Is radio working correctly? */ - int firmware_level; /* Message structuring level */ - int next_command; /* Next periodic command */ - unsigned int user_baud; /* The user-selected baud rate */ - int mtu; /* Our mtu (to spot changes!) */ - long watchdog_doprobe; /* Next time to test the radio */ - long watchdog_doreset; /* Time to do next reset */ - long gratuitous_arp; /* Time to send next ARP refresh */ - long arp_interval; /* Next ARP interval */ - struct timer_list idle_timer; /* For periodic wakeup calls */ - MetricomAddress true_dev_addr; /* True address of radio */ - int manual_dev_addr; /* Hack: See note below */ - - FirmwareVersion firmware_version; /* The radio's firmware version */ - SerialNumber serial_number; /* The radio's serial number */ - BatteryVoltage battery_voltage; /* The radio's battery voltage */ - - /* - * Other useful structures. - */ - - struct tty_struct *tty; /* ptr to TTY structure */ - struct net_device *dev; /* Our device structure */ - - /* - * Neighbour radio records - */ - - MetricomNodeTable portables; - MetricomNodeTable poletops; -}; - -/* - * Note: manual_dev_addr hack - * - * It is not possible to change the hardware address of a Metricom radio, - * or to send packets with a user-specified hardware source address, thus - * trying to manually set a hardware source address is a questionable - * thing to do. However, if the user *does* manually set the hardware - * source address of a STRIP interface, then the kernel will believe it, - * and use it in certain places. For example, the hardware address listed - * by ifconfig will be the manual address, not the true one. - * (Both addresses are listed in /proc/net/strip.) - * Also, ARP packets will be sent out giving the user-specified address as - * the source address, not the real address. This is dangerous, because - * it means you won't receive any replies -- the ARP replies will go to - * the specified address, which will be some other radio. The case where - * this is useful is when that other radio is also connected to the same - * machine. This allows you to connect a pair of radios to one machine, - * and to use one exclusively for inbound traffic, and the other - * exclusively for outbound traffic. Pretty neat, huh? - * - * Here's the full procedure to set this up: - * - * 1. "slattach" two interfaces, e.g. st0 for outgoing packets, - * and st1 for incoming packets - * - * 2. "ifconfig" st0 (outbound radio) to have the hardware address - * which is the real hardware address of st1 (inbound radio). - * Now when it sends out packets, it will masquerade as st1, and - * replies will be sent to that radio, which is exactly what we want. - * - * 3. Set the route table entry ("route add default ..." or - * "route add -net ...", as appropriate) to send packets via the st0 - * interface (outbound radio). Do not add any route which sends packets - * out via the st1 interface -- that radio is for inbound traffic only. - * - * 4. "ifconfig" st1 (inbound radio) to have hardware address zero. - * This tells the STRIP driver to "shut down" that interface and not - * send any packets through it. In particular, it stops sending the - * periodic gratuitous ARP packets that a STRIP interface normally sends. - * Also, when packets arrive on that interface, it will search the - * interface list to see if there is another interface who's manual - * hardware address matches its own real address (i.e. st0 in this - * example) and if so it will transfer ownership of the skbuff to - * that interface, so that it looks to the kernel as if the packet - * arrived on that interface. This is necessary because when the - * kernel sends an ARP packet on st0, it expects to get a reply on - * st0, and if it sees the reply come from st1 then it will ignore - * it (to be accurate, it puts the entry in the ARP table, but - * labelled in such a way that st0 can't use it). - * - * Thanks to Petros Maniatis for coming up with the idea of splitting - * inbound and outbound traffic between two interfaces, which turned - * out to be really easy to implement, even if it is a bit of a hack. - * - * Having set a manual address on an interface, you can restore it - * to automatic operation (where the address is automatically kept - * consistent with the real address of the radio) by setting a manual - * address of all ones, e.g. "ifconfig st0 hw strip FFFFFFFFFFFF" - * This 'turns off' manual override mode for the device address. - * - * Note: The IEEE 802 headers reported in tcpdump will show the *real* - * radio addresses the packets were sent and received from, so that you - * can see what is really going on with packets, and which interfaces - * they are really going through. - */ - - -/************************************************************************/ -/* Constants */ - -/* - * CommandString1 works on all radios - * Other CommandStrings are only used with firmware that provides structured responses. - * - * ats319=1 Enables Info message for node additions and deletions - * ats319=2 Enables Info message for a new best node - * ats319=4 Enables checksums - * ats319=8 Enables ACK messages - */ - -static const int MaxCommandStringLength = 32; -static const int CompatibilityCommand = 1; - -static const char CommandString0[] = "*&COMMAND*ATS319=7"; /* Turn on checksums & info messages */ -static const char CommandString1[] = "*&COMMAND*ATS305?"; /* Query radio name */ -static const char CommandString2[] = "*&COMMAND*ATS325?"; /* Query battery voltage */ -static const char CommandString3[] = "*&COMMAND*ATS300?"; /* Query version information */ -static const char CommandString4[] = "*&COMMAND*ATS311?"; /* Query poletop list */ -static const char CommandString5[] = "*&COMMAND*AT~LA"; /* Query portables list */ -typedef struct { - const char *string; - long length; -} StringDescriptor; - -static const StringDescriptor CommandString[] = { - {CommandString0, sizeof(CommandString0) - 1}, - {CommandString1, sizeof(CommandString1) - 1}, - {CommandString2, sizeof(CommandString2) - 1}, - {CommandString3, sizeof(CommandString3) - 1}, - {CommandString4, sizeof(CommandString4) - 1}, - {CommandString5, sizeof(CommandString5) - 1} -}; - -#define GOT_ALL_RADIO_INFO(S) \ - ((S)->firmware_version.c[0] && \ - (S)->battery_voltage.c[0] && \ - memcmp(&(S)->true_dev_addr, zero_address.c, sizeof(zero_address))) - -static const char hextable[16] = "0123456789ABCDEF"; - -static const MetricomAddress zero_address; -static const MetricomAddress broadcast_address = - { {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF} }; - -static const MetricomKey SIP0Key = { "SIP0" }; -static const MetricomKey ARP0Key = { "ARP0" }; -static const MetricomKey ATR_Key = { "ATR " }; -static const MetricomKey ACK_Key = { "ACK_" }; -static const MetricomKey INF_Key = { "INF_" }; -static const MetricomKey ERR_Key = { "ERR_" }; - -static const long MaxARPInterval = 60 * HZ; /* One minute */ - -/* - * Maximum Starmode packet length is 1183 bytes. Allowing 4 bytes for - * protocol key, 4 bytes for checksum, one byte for CR, and 65/64 expansion - * for STRIP encoding, that translates to a maximum payload MTU of 1155. - * Note: A standard NFS 1K data packet is a total of 0x480 (1152) bytes - * long, including IP header, UDP header, and NFS header. Setting the STRIP - * MTU to 1152 allows us to send default sized NFS packets without fragmentation. - */ -static const unsigned short MAX_SEND_MTU = 1152; -static const unsigned short MAX_RECV_MTU = 1500; /* Hoping for Ethernet sized packets in the future! */ -static const unsigned short DEFAULT_STRIP_MTU = 1152; -static const int STRIP_MAGIC = 0x5303; -static const long LongTime = 0x7FFFFFFF; - -/************************************************************************/ -/* Global variables */ - -static LIST_HEAD(strip_list); -static DEFINE_SPINLOCK(strip_lock); - -/************************************************************************/ -/* Macros */ - -/* Returns TRUE if text T begins with prefix P */ -#define has_prefix(T,L,P) (((L) >= sizeof(P)-1) && !strncmp((T), (P), sizeof(P)-1)) - -/* Returns TRUE if text T of length L is equal to string S */ -#define text_equal(T,L,S) (((L) == sizeof(S)-1) && !strncmp((T), (S), sizeof(S)-1)) - -#define READHEX(X) ((X)>='0' && (X)<='9' ? (X)-'0' : \ - (X)>='a' && (X)<='f' ? (X)-'a'+10 : \ - (X)>='A' && (X)<='F' ? (X)-'A'+10 : 0 ) - -#define READHEX16(X) ((__u16)(READHEX(X))) - -#define READDEC(X) ((X)>='0' && (X)<='9' ? (X)-'0' : 0) - -#define ARRAY_END(X) (&((X)[ARRAY_SIZE(X)])) - -#define JIFFIE_TO_SEC(X) ((X) / HZ) - - -/************************************************************************/ -/* Utility routines */ - -static int arp_query(unsigned char *haddr, u32 paddr, - struct net_device *dev) -{ - struct neighbour *neighbor_entry; - int ret = 0; - - neighbor_entry = neigh_lookup(&arp_tbl, &paddr, dev); - - if (neighbor_entry != NULL) { - neighbor_entry->used = jiffies; - if (neighbor_entry->nud_state & NUD_VALID) { - memcpy(haddr, neighbor_entry->ha, dev->addr_len); - ret = 1; - } - neigh_release(neighbor_entry); - } - return ret; -} - -static void DumpData(char *msg, struct strip *strip_info, __u8 * ptr, - __u8 * end) -{ - static const int MAX_DumpData = 80; - __u8 pkt_text[MAX_DumpData], *p = pkt_text; - - *p++ = '\"'; - - while (ptr < end && p < &pkt_text[MAX_DumpData - 4]) { - if (*ptr == '\\') { - *p++ = '\\'; - *p++ = '\\'; - } else { - if (*ptr >= 32 && *ptr <= 126) { - *p++ = *ptr; - } else { - sprintf(p, "\\%02X", *ptr); - p += 3; - } - } - ptr++; - } - - if (ptr == end) - *p++ = '\"'; - *p++ = 0; - - printk(KERN_INFO "%s: %-13s%s\n", strip_info->dev->name, msg, pkt_text); -} - - -/************************************************************************/ -/* Byte stuffing/unstuffing routines */ - -/* Stuffing scheme: - * 00 Unused (reserved character) - * 01-3F Run of 2-64 different characters - * 40-7F Run of 1-64 different characters plus a single zero at the end - * 80-BF Run of 1-64 of the same character - * C0-FF Run of 1-64 zeroes (ASCII 0) - */ - -typedef enum { - Stuff_Diff = 0x00, - Stuff_DiffZero = 0x40, - Stuff_Same = 0x80, - Stuff_Zero = 0xC0, - Stuff_NoCode = 0xFF, /* Special code, meaning no code selected */ - - Stuff_CodeMask = 0xC0, - Stuff_CountMask = 0x3F, - Stuff_MaxCount = 0x3F, - Stuff_Magic = 0x0D /* The value we are eliminating */ -} StuffingCode; - -/* StuffData encodes the data starting at "src" for "length" bytes. - * It writes it to the buffer pointed to by "dst" (which must be at least - * as long as 1 + 65/64 of the input length). The output may be up to 1.6% - * larger than the input for pathological input, but will usually be smaller. - * StuffData returns the new value of the dst pointer as its result. - * "code_ptr_ptr" points to a "__u8 *" which is used to hold encoding state - * between calls, allowing an encoded packet to be incrementally built up - * from small parts. On the first call, the "__u8 *" pointed to should be - * initialized to NULL; between subsequent calls the calling routine should - * leave the value alone and simply pass it back unchanged so that the - * encoder can recover its current state. - */ - -#define StuffData_FinishBlock(X) \ -(*code_ptr = (X) ^ Stuff_Magic, code = Stuff_NoCode) - -static __u8 *StuffData(__u8 * src, __u32 length, __u8 * dst, - __u8 ** code_ptr_ptr) -{ - __u8 *end = src + length; - __u8 *code_ptr = *code_ptr_ptr; - __u8 code = Stuff_NoCode, count = 0; - - if (!length) - return (dst); - - if (code_ptr) { - /* - * Recover state from last call, if applicable - */ - code = (*code_ptr ^ Stuff_Magic) & Stuff_CodeMask; - count = (*code_ptr ^ Stuff_Magic) & Stuff_CountMask; - } - - while (src < end) { - switch (code) { - /* Stuff_NoCode: If no current code, select one */ - case Stuff_NoCode: - /* Record where we're going to put this code */ - code_ptr = dst++; - count = 0; /* Reset the count (zero means one instance) */ - /* Tentatively start a new block */ - if (*src == 0) { - code = Stuff_Zero; - src++; - } else { - code = Stuff_Same; - *dst++ = *src++ ^ Stuff_Magic; - } - /* Note: We optimistically assume run of same -- */ - /* which will be fixed later in Stuff_Same */ - /* if it turns out not to be true. */ - break; - - /* Stuff_Zero: We already have at least one zero encoded */ - case Stuff_Zero: - /* If another zero, count it, else finish this code block */ - if (*src == 0) { - count++; - src++; - } else { - StuffData_FinishBlock(Stuff_Zero + count); - } - break; - - /* Stuff_Same: We already have at least one byte encoded */ - case Stuff_Same: - /* If another one the same, count it */ - if ((*src ^ Stuff_Magic) == code_ptr[1]) { - count++; - src++; - break; - } - /* else, this byte does not match this block. */ - /* If we already have two or more bytes encoded, finish this code block */ - if (count) { - StuffData_FinishBlock(Stuff_Same + count); - break; - } - /* else, we only have one so far, so switch to Stuff_Diff code */ - code = Stuff_Diff; - /* and fall through to Stuff_Diff case below - * Note cunning cleverness here: case Stuff_Diff compares - * the current character with the previous two to see if it - * has a run of three the same. Won't this be an error if - * there aren't two previous characters stored to compare with? - * No. Because we know the current character is *not* the same - * as the previous one, the first test below will necessarily - * fail and the send half of the "if" won't be executed. - */ - - /* Stuff_Diff: We have at least two *different* bytes encoded */ - case Stuff_Diff: - /* If this is a zero, must encode a Stuff_DiffZero, and begin a new block */ - if (*src == 0) { - StuffData_FinishBlock(Stuff_DiffZero + - count); - } - /* else, if we have three in a row, it is worth starting a Stuff_Same block */ - else if ((*src ^ Stuff_Magic) == dst[-1] - && dst[-1] == dst[-2]) { - /* Back off the last two characters we encoded */ - code += count - 2; - /* Note: "Stuff_Diff + 0" is an illegal code */ - if (code == Stuff_Diff + 0) { - code = Stuff_Same + 0; - } - StuffData_FinishBlock(code); - code_ptr = dst - 2; - /* dst[-1] already holds the correct value */ - count = 2; /* 2 means three bytes encoded */ - code = Stuff_Same; - } - /* else, another different byte, so add it to the block */ - else { - *dst++ = *src ^ Stuff_Magic; - count++; - } - src++; /* Consume the byte */ - break; - } - if (count == Stuff_MaxCount) { - StuffData_FinishBlock(code + count); - } - } - if (code == Stuff_NoCode) { - *code_ptr_ptr = NULL; - } else { - *code_ptr_ptr = code_ptr; - StuffData_FinishBlock(code + count); - } - return (dst); -} - -/* - * UnStuffData decodes the data at "src", up to (but not including) "end". - * It writes the decoded data into the buffer pointed to by "dst", up to a - * maximum of "dst_length", and returns the new value of "src" so that a - * follow-on call can read more data, continuing from where the first left off. - * - * There are three types of results: - * 1. The source data runs out before extracting "dst_length" bytes: - * UnStuffData returns NULL to indicate failure. - * 2. The source data produces exactly "dst_length" bytes: - * UnStuffData returns new_src = end to indicate that all bytes were consumed. - * 3. "dst_length" bytes are extracted, with more remaining. - * UnStuffData returns new_src < end to indicate that there are more bytes - * to be read. - * - * Note: The decoding may be destructive, in that it may alter the source - * data in the process of decoding it (this is necessary to allow a follow-on - * call to resume correctly). - */ - -static __u8 *UnStuffData(__u8 * src, __u8 * end, __u8 * dst, - __u32 dst_length) -{ - __u8 *dst_end = dst + dst_length; - /* Sanity check */ - if (!src || !end || !dst || !dst_length) - return (NULL); - while (src < end && dst < dst_end) { - int count = (*src ^ Stuff_Magic) & Stuff_CountMask; - switch ((*src ^ Stuff_Magic) & Stuff_CodeMask) { - case Stuff_Diff: - if (src + 1 + count >= end) - return (NULL); - do { - *dst++ = *++src ^ Stuff_Magic; - } - while (--count >= 0 && dst < dst_end); - if (count < 0) - src += 1; - else { - if (count == 0) - *src = Stuff_Same ^ Stuff_Magic; - else - *src = - (Stuff_Diff + - count) ^ Stuff_Magic; - } - break; - case Stuff_DiffZero: - if (src + 1 + count >= end) - return (NULL); - do { - *dst++ = *++src ^ Stuff_Magic; - } - while (--count >= 0 && dst < dst_end); - if (count < 0) - *src = Stuff_Zero ^ Stuff_Magic; - else - *src = - (Stuff_DiffZero + count) ^ Stuff_Magic; - break; - case Stuff_Same: - if (src + 1 >= end) - return (NULL); - do { - *dst++ = src[1] ^ Stuff_Magic; - } - while (--count >= 0 && dst < dst_end); - if (count < 0) - src += 2; - else - *src = (Stuff_Same + count) ^ Stuff_Magic; - break; - case Stuff_Zero: - do { - *dst++ = 0; - } - while (--count >= 0 && dst < dst_end); - if (count < 0) - src += 1; - else - *src = (Stuff_Zero + count) ^ Stuff_Magic; - break; - } - } - if (dst < dst_end) - return (NULL); - else - return (src); -} - - -/************************************************************************/ -/* General routines for STRIP */ - -/* - * set_baud sets the baud rate to the rate defined by baudcode - */ -static void set_baud(struct tty_struct *tty, speed_t baudrate) -{ - struct ktermios old_termios; - - mutex_lock(&tty->termios_mutex); - old_termios =*(tty->termios); - tty_encode_baud_rate(tty, baudrate, baudrate); - tty->ops->set_termios(tty, &old_termios); - mutex_unlock(&tty->termios_mutex); -} - -/* - * Convert a string to a Metricom Address. - */ - -#define IS_RADIO_ADDRESS(p) ( \ - isdigit((p)[0]) && isdigit((p)[1]) && isdigit((p)[2]) && isdigit((p)[3]) && \ - (p)[4] == '-' && \ - isdigit((p)[5]) && isdigit((p)[6]) && isdigit((p)[7]) && isdigit((p)[8]) ) - -static int string_to_radio_address(MetricomAddress * addr, __u8 * p) -{ - if (!IS_RADIO_ADDRESS(p)) - return (1); - addr->c[0] = 0; - addr->c[1] = 0; - addr->c[2] = READHEX(p[0]) << 4 | READHEX(p[1]); - addr->c[3] = READHEX(p[2]) << 4 | READHEX(p[3]); - addr->c[4] = READHEX(p[5]) << 4 | READHEX(p[6]); - addr->c[5] = READHEX(p[7]) << 4 | READHEX(p[8]); - return (0); -} - -/* - * Convert a Metricom Address to a string. - */ - -static __u8 *radio_address_to_string(const MetricomAddress * addr, - MetricomAddressString * p) -{ - sprintf(p->c, "%02X%02X-%02X%02X", addr->c[2], addr->c[3], - addr->c[4], addr->c[5]); - return (p->c); -} - -/* - * Note: Must make sure sx_size is big enough to receive a stuffed - * MAX_RECV_MTU packet. Additionally, we also want to ensure that it's - * big enough to receive a large radio neighbour list (currently 4K). - */ - -static int allocate_buffers(struct strip *strip_info, int mtu) -{ - struct net_device *dev = strip_info->dev; - int sx_size = max_t(int, STRIP_ENCAP_SIZE(MAX_RECV_MTU), 4096); - int tx_size = STRIP_ENCAP_SIZE(mtu) + MaxCommandStringLength; - __u8 *r = kmalloc(MAX_RECV_MTU, GFP_ATOMIC); - __u8 *s = kmalloc(sx_size, GFP_ATOMIC); - __u8 *t = kmalloc(tx_size, GFP_ATOMIC); - if (r && s && t) { - strip_info->rx_buff = r; - strip_info->sx_buff = s; - strip_info->tx_buff = t; - strip_info->sx_size = sx_size; - strip_info->tx_size = tx_size; - strip_info->mtu = dev->mtu = mtu; - return (1); - } - kfree(r); - kfree(s); - kfree(t); - return (0); -} - -/* - * MTU has been changed by the IP layer. - * We could be in - * an upcall from the tty driver, or in an ip packet queue. - */ -static int strip_change_mtu(struct net_device *dev, int new_mtu) -{ - struct strip *strip_info = netdev_priv(dev); - int old_mtu = strip_info->mtu; - unsigned char *orbuff = strip_info->rx_buff; - unsigned char *osbuff = strip_info->sx_buff; - unsigned char *otbuff = strip_info->tx_buff; - - if (new_mtu > MAX_SEND_MTU) { - printk(KERN_ERR - "%s: MTU exceeds maximum allowable (%d), MTU change cancelled.\n", - strip_info->dev->name, MAX_SEND_MTU); - return -EINVAL; - } - - spin_lock_bh(&strip_lock); - if (!allocate_buffers(strip_info, new_mtu)) { - printk(KERN_ERR "%s: unable to grow strip buffers, MTU change cancelled.\n", - strip_info->dev->name); - spin_unlock_bh(&strip_lock); - return -ENOMEM; - } - - if (strip_info->sx_count) { - if (strip_info->sx_count <= strip_info->sx_size) - memcpy(strip_info->sx_buff, osbuff, - strip_info->sx_count); - else { - strip_info->discard = strip_info->sx_count; - strip_info->rx_over_errors++; - } - } - - if (strip_info->tx_left) { - if (strip_info->tx_left <= strip_info->tx_size) - memcpy(strip_info->tx_buff, strip_info->tx_head, - strip_info->tx_left); - else { - strip_info->tx_left = 0; - strip_info->tx_dropped++; - } - } - strip_info->tx_head = strip_info->tx_buff; - spin_unlock_bh(&strip_lock); - - printk(KERN_NOTICE "%s: strip MTU changed fom %d to %d.\n", - strip_info->dev->name, old_mtu, strip_info->mtu); - - kfree(orbuff); - kfree(osbuff); - kfree(otbuff); - return 0; -} - -static void strip_unlock(struct strip *strip_info) -{ - /* - * Set the timer to go off in one second. - */ - strip_info->idle_timer.expires = jiffies + 1 * HZ; - add_timer(&strip_info->idle_timer); - netif_wake_queue(strip_info->dev); -} - - - -/* - * If the time is in the near future, time_delta prints the number of - * seconds to go into the buffer and returns the address of the buffer. - * If the time is not in the near future, it returns the address of the - * string "Not scheduled" The buffer must be long enough to contain the - * ascii representation of the number plus 9 charactes for the " seconds" - * and the null character. - */ -#ifdef CONFIG_PROC_FS -static char *time_delta(char buffer[], long time) -{ - time -= jiffies; - if (time > LongTime / 2) - return ("Not scheduled"); - if (time < 0) - time = 0; /* Don't print negative times */ - sprintf(buffer, "%ld seconds", time / HZ); - return (buffer); -} - -/* get Nth element of the linked list */ -static struct strip *strip_get_idx(loff_t pos) -{ - struct strip *str; - int i = 0; - - list_for_each_entry_rcu(str, &strip_list, list) { - if (pos == i) - return str; - ++i; - } - return NULL; -} - -static void *strip_seq_start(struct seq_file *seq, loff_t *pos) - __acquires(RCU) -{ - rcu_read_lock(); - return *pos ? strip_get_idx(*pos - 1) : SEQ_START_TOKEN; -} - -static void *strip_seq_next(struct seq_file *seq, void *v, loff_t *pos) -{ - struct list_head *l; - struct strip *s; - - ++*pos; - if (v == SEQ_START_TOKEN) - return strip_get_idx(1); - - s = v; - l = &s->list; - list_for_each_continue_rcu(l, &strip_list) { - return list_entry(l, struct strip, list); - } - return NULL; -} - -static void strip_seq_stop(struct seq_file *seq, void *v) - __releases(RCU) -{ - rcu_read_unlock(); -} - -static void strip_seq_neighbours(struct seq_file *seq, - const MetricomNodeTable * table, - const char *title) -{ - /* We wrap this in a do/while loop, so if the table changes */ - /* while we're reading it, we just go around and try again. */ - struct timeval t; - - do { - int i; - t = table->timestamp; - if (table->num_nodes) - seq_printf(seq, "\n %s\n", title); - for (i = 0; i < table->num_nodes; i++) { - MetricomNode node; - - spin_lock_bh(&strip_lock); - node = table->node[i]; - spin_unlock_bh(&strip_lock); - seq_printf(seq, " %s\n", node.c); - } - } while (table->timestamp.tv_sec != t.tv_sec - || table->timestamp.tv_usec != t.tv_usec); -} - -/* - * This function prints radio status information via the seq_file - * interface. The interface takes care of buffer size and over - * run issues. - * - * The buffer in seq_file is PAGESIZE (4K) - * so this routine should never print more or it will get truncated. - * With the maximum of 32 portables and 32 poletops - * reported, the routine outputs 3107 bytes into the buffer. - */ -static void strip_seq_status_info(struct seq_file *seq, - const struct strip *strip_info) -{ - char temp[32]; - MetricomAddressString addr_string; - - /* First, we must copy all of our data to a safe place, */ - /* in case a serial interrupt comes in and changes it. */ - int tx_left = strip_info->tx_left; - unsigned long rx_average_pps = strip_info->rx_average_pps; - unsigned long tx_average_pps = strip_info->tx_average_pps; - unsigned long sx_average_pps = strip_info->sx_average_pps; - int working = strip_info->working; - int firmware_level = strip_info->firmware_level; - long watchdog_doprobe = strip_info->watchdog_doprobe; - long watchdog_doreset = strip_info->watchdog_doreset; - long gratuitous_arp = strip_info->gratuitous_arp; - long arp_interval = strip_info->arp_interval; - FirmwareVersion firmware_version = strip_info->firmware_version; - SerialNumber serial_number = strip_info->serial_number; - BatteryVoltage battery_voltage = strip_info->battery_voltage; - char *if_name = strip_info->dev->name; - MetricomAddress true_dev_addr = strip_info->true_dev_addr; - MetricomAddress dev_dev_addr = - *(MetricomAddress *) strip_info->dev->dev_addr; - int manual_dev_addr = strip_info->manual_dev_addr; -#ifdef EXT_COUNTERS - unsigned long rx_bytes = strip_info->rx_bytes; - unsigned long tx_bytes = strip_info->tx_bytes; - unsigned long rx_rbytes = strip_info->rx_rbytes; - unsigned long tx_rbytes = strip_info->tx_rbytes; - unsigned long rx_sbytes = strip_info->rx_sbytes; - unsigned long tx_sbytes = strip_info->tx_sbytes; - unsigned long rx_ebytes = strip_info->rx_ebytes; - unsigned long tx_ebytes = strip_info->tx_ebytes; -#endif - - seq_printf(seq, "\nInterface name\t\t%s\n", if_name); - seq_printf(seq, " Radio working:\t\t%s\n", working ? "Yes" : "No"); - radio_address_to_string(&true_dev_addr, &addr_string); - seq_printf(seq, " Radio address:\t\t%s\n", addr_string.c); - if (manual_dev_addr) { - radio_address_to_string(&dev_dev_addr, &addr_string); - seq_printf(seq, " Device address:\t%s\n", addr_string.c); - } - seq_printf(seq, " Firmware version:\t%s", !working ? "Unknown" : - !firmware_level ? "Should be upgraded" : - firmware_version.c); - if (firmware_level >= ChecksummedMessages) - seq_printf(seq, " (Checksums Enabled)"); - seq_printf(seq, "\n"); - seq_printf(seq, " Serial number:\t\t%s\n", serial_number.c); - seq_printf(seq, " Battery voltage:\t%s\n", battery_voltage.c); - seq_printf(seq, " Transmit queue (bytes):%d\n", tx_left); - seq_printf(seq, " Receive packet rate: %ld packets per second\n", - rx_average_pps / 8); - seq_printf(seq, " Transmit packet rate: %ld packets per second\n", - tx_average_pps / 8); - seq_printf(seq, " Sent packet rate: %ld packets per second\n", - sx_average_pps / 8); - seq_printf(seq, " Next watchdog probe:\t%s\n", - time_delta(temp, watchdog_doprobe)); - seq_printf(seq, " Next watchdog reset:\t%s\n", - time_delta(temp, watchdog_doreset)); - seq_printf(seq, " Next gratuitous ARP:\t"); - - if (!memcmp - (strip_info->dev->dev_addr, zero_address.c, - sizeof(zero_address))) - seq_printf(seq, "Disabled\n"); - else { - seq_printf(seq, "%s\n", time_delta(temp, gratuitous_arp)); - seq_printf(seq, " Next ARP interval:\t%ld seconds\n", - JIFFIE_TO_SEC(arp_interval)); - } - - if (working) { -#ifdef EXT_COUNTERS - seq_printf(seq, "\n"); - seq_printf(seq, - " Total bytes: \trx:\t%lu\ttx:\t%lu\n", - rx_bytes, tx_bytes); - seq_printf(seq, - " thru radio: \trx:\t%lu\ttx:\t%lu\n", - rx_rbytes, tx_rbytes); - seq_printf(seq, - " thru serial port: \trx:\t%lu\ttx:\t%lu\n", - rx_sbytes, tx_sbytes); - seq_printf(seq, - " Total stat/err bytes:\trx:\t%lu\ttx:\t%lu\n", - rx_ebytes, tx_ebytes); -#endif - strip_seq_neighbours(seq, &strip_info->poletops, - "Poletops:"); - strip_seq_neighbours(seq, &strip_info->portables, - "Portables:"); - } -} - -/* - * This function is exports status information from the STRIP driver through - * the /proc file system. - */ -static int strip_seq_show(struct seq_file *seq, void *v) -{ - if (v == SEQ_START_TOKEN) - seq_printf(seq, "strip_version: %s\n", StripVersion); - else - strip_seq_status_info(seq, (const struct strip *)v); - return 0; -} - - -static const struct seq_operations strip_seq_ops = { - .start = strip_seq_start, - .next = strip_seq_next, - .stop = strip_seq_stop, - .show = strip_seq_show, -}; - -static int strip_seq_open(struct inode *inode, struct file *file) -{ - return seq_open(file, &strip_seq_ops); -} - -static const struct file_operations strip_seq_fops = { - .owner = THIS_MODULE, - .open = strip_seq_open, - .read = seq_read, - .llseek = seq_lseek, - .release = seq_release, -}; -#endif - - - -/************************************************************************/ -/* Sending routines */ - -static void ResetRadio(struct strip *strip_info) -{ - struct tty_struct *tty = strip_info->tty; - static const char init[] = "ate0q1dt**starmode\r**"; - StringDescriptor s = { init, sizeof(init) - 1 }; - - /* - * If the radio isn't working anymore, - * we should clear the old status information. - */ - if (strip_info->working) { - printk(KERN_INFO "%s: No response: Resetting radio.\n", - strip_info->dev->name); - strip_info->firmware_version.c[0] = '\0'; - strip_info->serial_number.c[0] = '\0'; - strip_info->battery_voltage.c[0] = '\0'; - strip_info->portables.num_nodes = 0; - do_gettimeofday(&strip_info->portables.timestamp); - strip_info->poletops.num_nodes = 0; - do_gettimeofday(&strip_info->poletops.timestamp); - } - - strip_info->pps_timer = jiffies; - strip_info->rx_pps_count = 0; - strip_info->tx_pps_count = 0; - strip_info->sx_pps_count = 0; - strip_info->rx_average_pps = 0; - strip_info->tx_average_pps = 0; - strip_info->sx_average_pps = 0; - - /* Mark radio address as unknown */ - *(MetricomAddress *) & strip_info->true_dev_addr = zero_address; - if (!strip_info->manual_dev_addr) - *(MetricomAddress *) strip_info->dev->dev_addr = - zero_address; - strip_info->working = FALSE; - strip_info->firmware_level = NoStructure; - strip_info->next_command = CompatibilityCommand; - strip_info->watchdog_doprobe = jiffies + 10 * HZ; - strip_info->watchdog_doreset = jiffies + 1 * HZ; - - /* If the user has selected a baud rate above 38.4 see what magic we have to do */ - if (strip_info->user_baud > 38400) { - /* - * Subtle stuff: Pay attention :-) - * If the serial port is currently at the user's selected (>38.4) rate, - * then we temporarily switch to 19.2 and issue the ATS304 command - * to tell the radio to switch to the user's selected rate. - * If the serial port is not currently at that rate, that means we just - * issued the ATS304 command last time through, so this time we restore - * the user's selected rate and issue the normal starmode reset string. - */ - if (strip_info->user_baud == tty_get_baud_rate(tty)) { - static const char b0[] = "ate0q1s304=57600\r"; - static const char b1[] = "ate0q1s304=115200\r"; - static const StringDescriptor baudstring[2] = - { {b0, sizeof(b0) - 1} - , {b1, sizeof(b1) - 1} - }; - set_baud(tty, 19200); - if (strip_info->user_baud == 57600) - s = baudstring[0]; - else if (strip_info->user_baud == 115200) - s = baudstring[1]; - else - s = baudstring[1]; /* For now */ - } else - set_baud(tty, strip_info->user_baud); - } - - tty->ops->write(tty, s.string, s.length); -#ifdef EXT_COUNTERS - strip_info->tx_ebytes += s.length; -#endif -} - -/* - * Called by the driver when there's room for more data. If we have - * more packets to send, we send them here. - */ - -static void strip_write_some_more(struct tty_struct *tty) -{ - struct strip *strip_info = tty->disc_data; - - /* First make sure we're connected. */ - if (!strip_info || strip_info->magic != STRIP_MAGIC || - !netif_running(strip_info->dev)) - return; - - if (strip_info->tx_left > 0) { - int num_written = - tty->ops->write(tty, strip_info->tx_head, - strip_info->tx_left); - strip_info->tx_left -= num_written; - strip_info->tx_head += num_written; -#ifdef EXT_COUNTERS - strip_info->tx_sbytes += num_written; -#endif - } else { /* Else start transmission of another packet */ - - clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); - strip_unlock(strip_info); - } -} - -static __u8 *add_checksum(__u8 * buffer, __u8 * end) -{ - __u16 sum = 0; - __u8 *p = buffer; - while (p < end) - sum += *p++; - end[3] = hextable[sum & 0xF]; - sum >>= 4; - end[2] = hextable[sum & 0xF]; - sum >>= 4; - end[1] = hextable[sum & 0xF]; - sum >>= 4; - end[0] = hextable[sum & 0xF]; - return (end + 4); -} - -static unsigned char *strip_make_packet(unsigned char *buffer, - struct strip *strip_info, - struct sk_buff *skb) -{ - __u8 *ptr = buffer; - __u8 *stuffstate = NULL; - STRIP_Header *header = (STRIP_Header *) skb->data; - MetricomAddress haddr = header->dst_addr; - int len = skb->len - sizeof(STRIP_Header); - MetricomKey key; - - /*HexDump("strip_make_packet", strip_info, skb->data, skb->data + skb->len); */ - - if (header->protocol == htons(ETH_P_IP)) - key = SIP0Key; - else if (header->protocol == htons(ETH_P_ARP)) - key = ARP0Key; - else { - printk(KERN_ERR - "%s: strip_make_packet: Unknown packet type 0x%04X\n", - strip_info->dev->name, ntohs(header->protocol)); - return (NULL); - } - - if (len > strip_info->mtu) { - printk(KERN_ERR - "%s: Dropping oversized transmit packet: %d bytes\n", - strip_info->dev->name, len); - return (NULL); - } - - /* - * If we're sending to ourselves, discard the packet. - * (Metricom radios choke if they try to send a packet to their own address.) - */ - if (!memcmp(haddr.c, strip_info->true_dev_addr.c, sizeof(haddr))) { - printk(KERN_ERR "%s: Dropping packet addressed to self\n", - strip_info->dev->name); - return (NULL); - } - - /* - * If this is a broadcast packet, send it to our designated Metricom - * 'broadcast hub' radio (First byte of address being 0xFF means broadcast) - */ - if (haddr.c[0] == 0xFF) { - __be32 brd = 0; - struct in_device *in_dev; - - rcu_read_lock(); - in_dev = __in_dev_get_rcu(strip_info->dev); - if (in_dev == NULL) { - rcu_read_unlock(); - return NULL; - } - if (in_dev->ifa_list) - brd = in_dev->ifa_list->ifa_broadcast; - rcu_read_unlock(); - - /* arp_query returns 1 if it succeeds in looking up the address, 0 if it fails */ - if (!arp_query(haddr.c, brd, strip_info->dev)) { - printk(KERN_ERR - "%s: Unable to send packet (no broadcast hub configured)\n", - strip_info->dev->name); - return (NULL); - } - /* - * If we are the broadcast hub, don't bother sending to ourselves. - * (Metricom radios choke if they try to send a packet to their own address.) - */ - if (!memcmp - (haddr.c, strip_info->true_dev_addr.c, sizeof(haddr))) - return (NULL); - } - - *ptr++ = 0x0D; - *ptr++ = '*'; - *ptr++ = hextable[haddr.c[2] >> 4]; - *ptr++ = hextable[haddr.c[2] & 0xF]; - *ptr++ = hextable[haddr.c[3] >> 4]; - *ptr++ = hextable[haddr.c[3] & 0xF]; - *ptr++ = '-'; - *ptr++ = hextable[haddr.c[4] >> 4]; - *ptr++ = hextable[haddr.c[4] & 0xF]; - *ptr++ = hextable[haddr.c[5] >> 4]; - *ptr++ = hextable[haddr.c[5] & 0xF]; - *ptr++ = '*'; - *ptr++ = key.c[0]; - *ptr++ = key.c[1]; - *ptr++ = key.c[2]; - *ptr++ = key.c[3]; - - ptr = - StuffData(skb->data + sizeof(STRIP_Header), len, ptr, - &stuffstate); - - if (strip_info->firmware_level >= ChecksummedMessages) - ptr = add_checksum(buffer + 1, ptr); - - *ptr++ = 0x0D; - return (ptr); -} - -static void strip_send(struct strip *strip_info, struct sk_buff *skb) -{ - MetricomAddress haddr; - unsigned char *ptr = strip_info->tx_buff; - int doreset = (long) jiffies - strip_info->watchdog_doreset >= 0; - int doprobe = (long) jiffies - strip_info->watchdog_doprobe >= 0 - && !doreset; - __be32 addr, brd; - - /* - * 1. If we have a packet, encapsulate it and put it in the buffer - */ - if (skb) { - char *newptr = strip_make_packet(ptr, strip_info, skb); - strip_info->tx_pps_count++; - if (!newptr) - strip_info->tx_dropped++; - else { - ptr = newptr; - strip_info->sx_pps_count++; - strip_info->tx_packets++; /* Count another successful packet */ -#ifdef EXT_COUNTERS - strip_info->tx_bytes += skb->len; - strip_info->tx_rbytes += ptr - strip_info->tx_buff; -#endif - /*DumpData("Sending:", strip_info, strip_info->tx_buff, ptr); */ - /*HexDump("Sending", strip_info, strip_info->tx_buff, ptr); */ - } - } - - /* - * 2. If it is time for another tickle, tack it on, after the packet - */ - if (doprobe) { - StringDescriptor ts = CommandString[strip_info->next_command]; -#if TICKLE_TIMERS - { - struct timeval tv; - do_gettimeofday(&tv); - printk(KERN_INFO "**** Sending tickle string %d at %02d.%06d\n", - strip_info->next_command, tv.tv_sec % 100, - tv.tv_usec); - } -#endif - if (ptr == strip_info->tx_buff) - *ptr++ = 0x0D; - - *ptr++ = '*'; /* First send "**" to provoke an error message */ - *ptr++ = '*'; - - /* Then add the command */ - memcpy(ptr, ts.string, ts.length); - - /* Add a checksum ? */ - if (strip_info->firmware_level < ChecksummedMessages) - ptr += ts.length; - else - ptr = add_checksum(ptr, ptr + ts.length); - - *ptr++ = 0x0D; /* Terminate the command with a <CR> */ - - /* Cycle to next periodic command? */ - if (strip_info->firmware_level >= StructuredMessages) - if (++strip_info->next_command >= - ARRAY_SIZE(CommandString)) - strip_info->next_command = 0; -#ifdef EXT_COUNTERS - strip_info->tx_ebytes += ts.length; -#endif - strip_info->watchdog_doprobe = jiffies + 10 * HZ; - strip_info->watchdog_doreset = jiffies + 1 * HZ; - /*printk(KERN_INFO "%s: Routine radio test.\n", strip_info->dev->name); */ - } - - /* - * 3. Set up the strip_info ready to send the data (if any). - */ - strip_info->tx_head = strip_info->tx_buff; - strip_info->tx_left = ptr - strip_info->tx_buff; - set_bit(TTY_DO_WRITE_WAKEUP, &strip_info->tty->flags); - /* - * 4. Debugging check to make sure we're not overflowing the buffer. - */ - if (strip_info->tx_size - strip_info->tx_left < 20) - printk(KERN_ERR "%s: Sending%5d bytes;%5d bytes free.\n", - strip_info->dev->name, strip_info->tx_left, - strip_info->tx_size - strip_info->tx_left); - - /* - * 5. If watchdog has expired, reset the radio. Note: if there's data waiting in - * the buffer, strip_write_some_more will send it after the reset has finished - */ - if (doreset) { - ResetRadio(strip_info); - return; - } - - if (1) { - struct in_device *in_dev; - - brd = addr = 0; - rcu_read_lock(); - in_dev = __in_dev_get_rcu(strip_info->dev); - if (in_dev) { - if (in_dev->ifa_list) { - brd = in_dev->ifa_list->ifa_broadcast; - addr = in_dev->ifa_list->ifa_local; - } - } - rcu_read_unlock(); - } - - - /* - * 6. If it is time for a periodic ARP, queue one up to be sent. - * We only do this if: - * 1. The radio is working - * 2. It's time to send another periodic ARP - * 3. We really know what our address is (and it is not manually set to zero) - * 4. We have a designated broadcast address configured - * If we queue up an ARP packet when we don't have a designated broadcast - * address configured, then the packet will just have to be discarded in - * strip_make_packet. This is not fatal, but it causes misleading information - * to be displayed in tcpdump. tcpdump will report that periodic APRs are - * being sent, when in fact they are not, because they are all being dropped - * in the strip_make_packet routine. - */ - if (strip_info->working - && (long) jiffies - strip_info->gratuitous_arp >= 0 - && memcmp(strip_info->dev->dev_addr, zero_address.c, - sizeof(zero_address)) - && arp_query(haddr.c, brd, strip_info->dev)) { - /*printk(KERN_INFO "%s: Sending gratuitous ARP with interval %ld\n", - strip_info->dev->name, strip_info->arp_interval / HZ); */ - strip_info->gratuitous_arp = - jiffies + strip_info->arp_interval; - strip_info->arp_interval *= 2; - if (strip_info->arp_interval > MaxARPInterval) - strip_info->arp_interval = MaxARPInterval; - if (addr) - arp_send(ARPOP_REPLY, ETH_P_ARP, addr, /* Target address of ARP packet is our address */ - strip_info->dev, /* Device to send packet on */ - addr, /* Source IP address this ARP packet comes from */ - NULL, /* Destination HW address is NULL (broadcast it) */ - strip_info->dev->dev_addr, /* Source HW address is our HW address */ - strip_info->dev->dev_addr); /* Target HW address is our HW address (redundant) */ - } - - /* - * 7. All ready. Start the transmission - */ - strip_write_some_more(strip_info->tty); -} - -/* Encapsulate a datagram and kick it into a TTY queue. */ -static netdev_tx_t strip_xmit(struct sk_buff *skb, struct net_device *dev) -{ - struct strip *strip_info = netdev_priv(dev); - - if (!netif_running(dev)) { - printk(KERN_ERR "%s: xmit call when iface is down\n", - dev->name); - return NETDEV_TX_BUSY; - } - - netif_stop_queue(dev); - - del_timer(&strip_info->idle_timer); - - - if (time_after(jiffies, strip_info->pps_timer + HZ)) { - unsigned long t = jiffies - strip_info->pps_timer; - unsigned long rx_pps_count = - DIV_ROUND_CLOSEST(strip_info->rx_pps_count*HZ*8, t); - unsigned long tx_pps_count = - DIV_ROUND_CLOSEST(strip_info->tx_pps_count*HZ*8, t); - unsigned long sx_pps_count = - DIV_ROUND_CLOSEST(strip_info->sx_pps_count*HZ*8, t); - - strip_info->pps_timer = jiffies; - strip_info->rx_pps_count = 0; - strip_info->tx_pps_count = 0; - strip_info->sx_pps_count = 0; - - strip_info->rx_average_pps = (strip_info->rx_average_pps + rx_pps_count + 1) / 2; - strip_info->tx_average_pps = (strip_info->tx_average_pps + tx_pps_count + 1) / 2; - strip_info->sx_average_pps = (strip_info->sx_average_pps + sx_pps_count + 1) / 2; - - if (rx_pps_count / 8 >= 10) - printk(KERN_INFO "%s: WARNING: Receiving %ld packets per second.\n", - strip_info->dev->name, rx_pps_count / 8); - if (tx_pps_count / 8 >= 10) - printk(KERN_INFO "%s: WARNING: Tx %ld packets per second.\n", - strip_info->dev->name, tx_pps_count / 8); - if (sx_pps_count / 8 >= 10) - printk(KERN_INFO "%s: WARNING: Sending %ld packets per second.\n", - strip_info->dev->name, sx_pps_count / 8); - } - - spin_lock_bh(&strip_lock); - - strip_send(strip_info, skb); - - spin_unlock_bh(&strip_lock); - - if (skb) - dev_kfree_skb(skb); - return NETDEV_TX_OK; -} - -/* - * IdleTask periodically calls strip_xmit, so even when we have no IP packets - * to send for an extended period of time, the watchdog processing still gets - * done to ensure that the radio stays in Starmode - */ - -static void strip_IdleTask(unsigned long parameter) -{ - strip_xmit(NULL, (struct net_device *) parameter); -} - -/* - * Create the MAC header for an arbitrary protocol layer - * - * saddr!=NULL means use this specific address (n/a for Metricom) - * saddr==NULL means use default device source address - * daddr!=NULL means use this destination address - * daddr==NULL means leave destination address alone - * (e.g. unresolved arp -- kernel will call - * rebuild_header later to fill in the address) - */ - -static int strip_header(struct sk_buff *skb, struct net_device *dev, - unsigned short type, const void *daddr, - const void *saddr, unsigned len) -{ - struct strip *strip_info = netdev_priv(dev); - STRIP_Header *header = (STRIP_Header *) skb_push(skb, sizeof(STRIP_Header)); - - /*printk(KERN_INFO "%s: strip_header 0x%04X %s\n", dev->name, type, - type == ETH_P_IP ? "IP" : type == ETH_P_ARP ? "ARP" : ""); */ - - header->src_addr = strip_info->true_dev_addr; - header->protocol = htons(type); - - /*HexDump("strip_header", netdev_priv(dev), skb->data, skb->data + skb->len); */ - - if (!daddr) - return (-dev->hard_header_len); - - header->dst_addr = *(MetricomAddress *) daddr; - return (dev->hard_header_len); -} - -/* - * Rebuild the MAC header. This is called after an ARP - * (or in future other address resolution) has completed on this - * sk_buff. We now let ARP fill in the other fields. - * I think this should return zero if packet is ready to send, - * or non-zero if it needs more time to do an address lookup - */ - -static int strip_rebuild_header(struct sk_buff *skb) -{ -#ifdef CONFIG_INET - STRIP_Header *header = (STRIP_Header *) skb->data; - - /* Arp find returns zero if if knows the address, */ - /* or if it doesn't know the address it sends an ARP packet and returns non-zero */ - return arp_find(header->dst_addr.c, skb) ? 1 : 0; -#else - return 0; -#endif -} - - -/************************************************************************/ -/* Receiving routines */ - -/* - * This function parses the response to the ATS300? command, - * extracting the radio version and serial number. - */ -static void get_radio_version(struct strip *strip_info, __u8 * ptr, __u8 * end) -{ - __u8 *p, *value_begin, *value_end; - int len; - - /* Determine the beginning of the second line of the payload */ - p = ptr; - while (p < end && *p != 10) - p++; - if (p >= end) - return; - p++; - value_begin = p; - - /* Determine the end of line */ - while (p < end && *p != 10) - p++; - if (p >= end) - return; - value_end = p; - p++; - - len = value_end - value_begin; - len = min_t(int, len, sizeof(FirmwareVersion) - 1); - if (strip_info->firmware_version.c[0] == 0) - printk(KERN_INFO "%s: Radio Firmware: %.*s\n", - strip_info->dev->name, len, value_begin); - sprintf(strip_info->firmware_version.c, "%.*s", len, value_begin); - - /* Look for the first colon */ - while (p < end && *p != ':') - p++; - if (p >= end) - return; - /* Skip over the space */ - p += 2; - len = sizeof(SerialNumber) - 1; - if (p + len <= end) { - sprintf(strip_info->serial_number.c, "%.*s", len, p); - } else { - printk(KERN_DEBUG - "STRIP: radio serial number shorter (%zd) than expected (%d)\n", - end - p, len); - } -} - -/* - * This function parses the response to the ATS325? command, - * extracting the radio battery voltage. - */ -static void get_radio_voltage(struct strip *strip_info, __u8 * ptr, __u8 * end) -{ - int len; - - len = sizeof(BatteryVoltage) - 1; - if (ptr + len <= end) { - sprintf(strip_info->battery_voltage.c, "%.*s", len, ptr); - } else { - printk(KERN_DEBUG - "STRIP: radio voltage string shorter (%zd) than expected (%d)\n", - end - ptr, len); - } -} - -/* - * This function parses the responses to the AT~LA and ATS311 commands, - * which list the radio's neighbours. - */ -static void get_radio_neighbours(MetricomNodeTable * table, __u8 * ptr, __u8 * end) -{ - table->num_nodes = 0; - while (ptr < end && table->num_nodes < NODE_TABLE_SIZE) { - MetricomNode *node = &table->node[table->num_nodes++]; - char *dst = node->c, *limit = dst + sizeof(*node) - 1; - while (ptr < end && *ptr <= 32) - ptr++; - while (ptr < end && dst < limit && *ptr != 10) - *dst++ = *ptr++; - *dst++ = 0; - while (ptr < end && ptr[-1] != 10) - ptr++; - } - do_gettimeofday(&table->timestamp); -} - -static int get_radio_address(struct strip *strip_info, __u8 * p) -{ - MetricomAddress addr; - - if (string_to_radio_address(&addr, p)) - return (1); - - /* See if our radio address has changed */ - if (memcmp(strip_info->true_dev_addr.c, addr.c, sizeof(addr))) { - MetricomAddressString addr_string; - radio_address_to_string(&addr, &addr_string); - printk(KERN_INFO "%s: Radio address = %s\n", - strip_info->dev->name, addr_string.c); - strip_info->true_dev_addr = addr; - if (!strip_info->manual_dev_addr) - *(MetricomAddress *) strip_info->dev->dev_addr = - addr; - /* Give the radio a few seconds to get its head straight, then send an arp */ - strip_info->gratuitous_arp = jiffies + 15 * HZ; - strip_info->arp_interval = 1 * HZ; - } - return (0); -} - -static int verify_checksum(struct strip *strip_info) -{ - __u8 *p = strip_info->sx_buff; - __u8 *end = strip_info->sx_buff + strip_info->sx_count - 4; - u_short sum = - (READHEX16(end[0]) << 12) | (READHEX16(end[1]) << 8) | - (READHEX16(end[2]) << 4) | (READHEX16(end[3])); - while (p < end) - sum -= *p++; - if (sum == 0 && strip_info->firmware_level == StructuredMessages) { - strip_info->firmware_level = ChecksummedMessages; - printk(KERN_INFO "%s: Radio provides message checksums\n", - strip_info->dev->name); - } - return (sum == 0); -} - -static void RecvErr(char *msg, struct strip *strip_info) -{ - __u8 *ptr = strip_info->sx_buff; - __u8 *end = strip_info->sx_buff + strip_info->sx_count; - DumpData(msg, strip_info, ptr, end); - strip_info->rx_errors++; -} - -static void RecvErr_Message(struct strip *strip_info, __u8 * sendername, - const __u8 * msg, u_long len) -{ - if (has_prefix(msg, len, "001")) { /* Not in StarMode! */ - RecvErr("Error Msg:", strip_info); - printk(KERN_INFO "%s: Radio %s is not in StarMode\n", - strip_info->dev->name, sendername); - } - - else if (has_prefix(msg, len, "002")) { /* Remap handle */ - /* We ignore "Remap handle" messages for now */ - } - - else if (has_prefix(msg, len, "003")) { /* Can't resolve name */ - RecvErr("Error Msg:", strip_info); - printk(KERN_INFO "%s: Destination radio name is unknown\n", - strip_info->dev->name); - } - - else if (has_prefix(msg, len, "004")) { /* Name too small or missing */ - strip_info->watchdog_doreset = jiffies + LongTime; -#if TICKLE_TIMERS - { - struct timeval tv; - do_gettimeofday(&tv); - printk(KERN_INFO - "**** Got ERR_004 response at %02d.%06d\n", - tv.tv_sec % 100, tv.tv_usec); - } -#endif - if (!strip_info->working) { - strip_info->working = TRUE; - printk(KERN_INFO "%s: Radio now in starmode\n", - strip_info->dev->name); - /* - * If the radio has just entered a working state, we should do our first - * probe ASAP, so that we find out our radio address etc. without delay. - */ - strip_info->watchdog_doprobe = jiffies; - } - if (strip_info->firmware_level == NoStructure && sendername) { - strip_info->firmware_level = StructuredMessages; - strip_info->next_command = 0; /* Try to enable checksums ASAP */ - printk(KERN_INFO - "%s: Radio provides structured messages\n", - strip_info->dev->name); - } - if (strip_info->firmware_level >= StructuredMessages) { - /* - * If this message has a valid checksum on the end, then the call to verify_checksum - * will elevate the firmware_level to ChecksummedMessages for us. (The actual return - * code from verify_checksum is ignored here.) - */ - verify_checksum(strip_info); - /* - * If the radio has structured messages but we don't yet have all our information about it, - * we should do probes without delay, until we have gathered all the information - */ - if (!GOT_ALL_RADIO_INFO(strip_info)) - strip_info->watchdog_doprobe = jiffies; - } - } - - else if (has_prefix(msg, len, "005")) /* Bad count specification */ - RecvErr("Error Msg:", strip_info); - - else if (has_prefix(msg, len, "006")) /* Header too big */ - RecvErr("Error Msg:", strip_info); - - else if (has_prefix(msg, len, "007")) { /* Body too big */ - RecvErr("Error Msg:", strip_info); - printk(KERN_ERR - "%s: Error! Packet size too big for radio.\n", - strip_info->dev->name); - } - - else if (has_prefix(msg, len, "008")) { /* Bad character in name */ - RecvErr("Error Msg:", strip_info); - printk(KERN_ERR - "%s: Radio name contains illegal character\n", - strip_info->dev->name); - } - - else if (has_prefix(msg, len, "009")) /* No count or line terminator */ - RecvErr("Error Msg:", strip_info); - - else if (has_prefix(msg, len, "010")) /* Invalid checksum */ - RecvErr("Error Msg:", strip_info); - - else if (has_prefix(msg, len, "011")) /* Checksum didn't match */ - RecvErr("Error Msg:", strip_info); - - else if (has_prefix(msg, len, "012")) /* Failed to transmit packet */ - RecvErr("Error Msg:", strip_info); - - else - RecvErr("Error Msg:", strip_info); -} - -static void process_AT_response(struct strip *strip_info, __u8 * ptr, - __u8 * end) -{ - u_long len; - __u8 *p = ptr; - while (p < end && p[-1] != 10) - p++; /* Skip past first newline character */ - /* Now ptr points to the AT command, and p points to the text of the response. */ - len = p - ptr; - -#if TICKLE_TIMERS - { - struct timeval tv; - do_gettimeofday(&tv); - printk(KERN_INFO "**** Got AT response %.7s at %02d.%06d\n", - ptr, tv.tv_sec % 100, tv.tv_usec); - } -#endif - - if (has_prefix(ptr, len, "ATS300?")) - get_radio_version(strip_info, p, end); - else if (has_prefix(ptr, len, "ATS305?")) - get_radio_address(strip_info, p); - else if (has_prefix(ptr, len, "ATS311?")) - get_radio_neighbours(&strip_info->poletops, p, end); - else if (has_prefix(ptr, len, "ATS319=7")) - verify_checksum(strip_info); - else if (has_prefix(ptr, len, "ATS325?")) - get_radio_voltage(strip_info, p, end); - else if (has_prefix(ptr, len, "AT~LA")) - get_radio_neighbours(&strip_info->portables, p, end); - else - RecvErr("Unknown AT Response:", strip_info); -} - -static void process_ACK(struct strip *strip_info, __u8 * ptr, __u8 * end) -{ - /* Currently we don't do anything with ACKs from the radio */ -} - -static void process_Info(struct strip *strip_info, __u8 * ptr, __u8 * end) -{ - if (ptr + 16 > end) - RecvErr("Bad Info Msg:", strip_info); -} - -static struct net_device *get_strip_dev(struct strip *strip_info) -{ - /* If our hardware address is *manually set* to zero, and we know our */ - /* real radio hardware address, try to find another strip device that has been */ - /* manually set to that address that we can 'transfer ownership' of this packet to */ - if (strip_info->manual_dev_addr && - !memcmp(strip_info->dev->dev_addr, zero_address.c, - sizeof(zero_address)) - && memcmp(&strip_info->true_dev_addr, zero_address.c, - sizeof(zero_address))) { - struct net_device *dev; - read_lock_bh(&dev_base_lock); - for_each_netdev(&init_net, dev) { - if (dev->type == strip_info->dev->type && - !memcmp(dev->dev_addr, - &strip_info->true_dev_addr, - sizeof(MetricomAddress))) { - printk(KERN_INFO - "%s: Transferred packet ownership to %s.\n", - strip_info->dev->name, dev->name); - read_unlock_bh(&dev_base_lock); - return (dev); - } - } - read_unlock_bh(&dev_base_lock); - } - return (strip_info->dev); -} - -/* - * Send one completely decapsulated datagram to the next layer. - */ - -static void deliver_packet(struct strip *strip_info, STRIP_Header * header, - __u16 packetlen) -{ - struct sk_buff *skb = dev_alloc_skb(sizeof(STRIP_Header) + packetlen); - if (!skb) { - printk(KERN_ERR "%s: memory squeeze, dropping packet.\n", - strip_info->dev->name); - strip_info->rx_dropped++; - } else { - memcpy(skb_put(skb, sizeof(STRIP_Header)), header, - sizeof(STRIP_Header)); - memcpy(skb_put(skb, packetlen), strip_info->rx_buff, - packetlen); - skb->dev = get_strip_dev(strip_info); - skb->protocol = header->protocol; - skb_reset_mac_header(skb); - - /* Having put a fake header on the front of the sk_buff for the */ - /* benefit of tools like tcpdump, skb_pull now 'consumes' that */ - /* fake header before we hand the packet up to the next layer. */ - skb_pull(skb, sizeof(STRIP_Header)); - - /* Finally, hand the packet up to the next layer (e.g. IP or ARP, etc.) */ - strip_info->rx_packets++; - strip_info->rx_pps_count++; -#ifdef EXT_COUNTERS - strip_info->rx_bytes += packetlen; -#endif - netif_rx(skb); - } -} - -static void process_IP_packet(struct strip *strip_info, - STRIP_Header * header, __u8 * ptr, - __u8 * end) -{ - __u16 packetlen; - - /* Decode start of the IP packet header */ - ptr = UnStuffData(ptr, end, strip_info->rx_buff, 4); - if (!ptr) { - RecvErr("IP Packet too short", strip_info); - return; - } - - packetlen = ((__u16) strip_info->rx_buff[2] << 8) | strip_info->rx_buff[3]; - - if (packetlen > MAX_RECV_MTU) { - printk(KERN_INFO "%s: Dropping oversized received IP packet: %d bytes\n", - strip_info->dev->name, packetlen); - strip_info->rx_dropped++; - return; - } - - /*printk(KERN_INFO "%s: Got %d byte IP packet\n", strip_info->dev->name, packetlen); */ - - /* Decode remainder of the IP packet */ - ptr = - UnStuffData(ptr, end, strip_info->rx_buff + 4, packetlen - 4); - if (!ptr) { - RecvErr("IP Packet too short", strip_info); - return; - } - - if (ptr < end) { - RecvErr("IP Packet too long", strip_info); - return; - } - - header->protocol = htons(ETH_P_IP); - - deliver_packet(strip_info, header, packetlen); -} - -static void process_ARP_packet(struct strip *strip_info, - STRIP_Header * header, __u8 * ptr, - __u8 * end) -{ - __u16 packetlen; - struct arphdr *arphdr = (struct arphdr *) strip_info->rx_buff; - - /* Decode start of the ARP packet */ - ptr = UnStuffData(ptr, end, strip_info->rx_buff, 8); - if (!ptr) { - RecvErr("ARP Packet too short", strip_info); - return; - } - - packetlen = 8 + (arphdr->ar_hln + arphdr->ar_pln) * 2; - - if (packetlen > MAX_RECV_MTU) { - printk(KERN_INFO - "%s: Dropping oversized received ARP packet: %d bytes\n", - strip_info->dev->name, packetlen); - strip_info->rx_dropped++; - return; - } - - /*printk(KERN_INFO "%s: Got %d byte ARP %s\n", - strip_info->dev->name, packetlen, - ntohs(arphdr->ar_op) == ARPOP_REQUEST ? "request" : "reply"); */ - - /* Decode remainder of the ARP packet */ - ptr = - UnStuffData(ptr, end, strip_info->rx_buff + 8, packetlen - 8); - if (!ptr) { - RecvErr("ARP Packet too short", strip_info); - return; - } - - if (ptr < end) { - RecvErr("ARP Packet too long", strip_info); - return; - } - - header->protocol = htons(ETH_P_ARP); - - deliver_packet(strip_info, header, packetlen); -} - -/* - * process_text_message processes a <CR>-terminated block of data received - * from the radio that doesn't begin with a '*' character. All normal - * Starmode communication messages with the radio begin with a '*', - * so any text that does not indicates a serial port error, a radio that - * is in Hayes command mode instead of Starmode, or a radio with really - * old firmware that doesn't frame its Starmode responses properly. - */ -static void process_text_message(struct strip *strip_info) -{ - __u8 *msg = strip_info->sx_buff; - int len = strip_info->sx_count; - - /* Check for anything that looks like it might be our radio name */ - /* (This is here for backwards compatibility with old firmware) */ - if (len == 9 && get_radio_address(strip_info, msg) == 0) - return; - - if (text_equal(msg, len, "OK")) - return; /* Ignore 'OK' responses from prior commands */ - if (text_equal(msg, len, "ERROR")) - return; /* Ignore 'ERROR' messages */ - if (has_prefix(msg, len, "ate0q1")) - return; /* Ignore character echo back from the radio */ - - /* Catch other error messages */ - /* (This is here for backwards compatibility with old firmware) */ - if (has_prefix(msg, len, "ERR_")) { - RecvErr_Message(strip_info, NULL, &msg[4], len - 4); - return; - } - - RecvErr("No initial *", strip_info); -} - -/* - * process_message processes a <CR>-terminated block of data received - * from the radio. If the radio is not in Starmode or has old firmware, - * it may be a line of text in response to an AT command. Ideally, with - * a current radio that's properly in Starmode, all data received should - * be properly framed and checksummed radio message blocks, containing - * either a starmode packet, or a other communication from the radio - * firmware, like "INF_" Info messages and &COMMAND responses. - */ -static void process_message(struct strip *strip_info) -{ - STRIP_Header header = { zero_address, zero_address, 0 }; - __u8 *ptr = strip_info->sx_buff; - __u8 *end = strip_info->sx_buff + strip_info->sx_count; - __u8 sendername[32], *sptr = sendername; - MetricomKey key; - - /*HexDump("Receiving", strip_info, ptr, end); */ - - /* Check for start of address marker, and then skip over it */ - if (*ptr == '*') - ptr++; - else { - process_text_message(strip_info); - return; - } - - /* Copy out the return address */ - while (ptr < end && *ptr != '*' - && sptr < ARRAY_END(sendername) - 1) - *sptr++ = *ptr++; - *sptr = 0; /* Null terminate the sender name */ - - /* Check for end of address marker, and skip over it */ - if (ptr >= end || *ptr != '*') { - RecvErr("No second *", strip_info); - return; - } - ptr++; /* Skip the second '*' */ - - /* If the sender name is "&COMMAND", ignore this 'packet' */ - /* (This is here for backwards compatibility with old firmware) */ - if (!strcmp(sendername, "&COMMAND")) { - strip_info->firmware_level = NoStructure; - strip_info->next_command = CompatibilityCommand; - return; - } - - if (ptr + 4 > end) { - RecvErr("No proto key", strip_info); - return; - } - - /* Get the protocol key out of the buffer */ - key.c[0] = *ptr++; - key.c[1] = *ptr++; - key.c[2] = *ptr++; - key.c[3] = *ptr++; - - /* If we're using checksums, verify the checksum at the end of the packet */ - if (strip_info->firmware_level >= ChecksummedMessages) { - end -= 4; /* Chop the last four bytes off the packet (they're the checksum) */ - if (ptr > end) { - RecvErr("Missing Checksum", strip_info); - return; - } - if (!verify_checksum(strip_info)) { - RecvErr("Bad Checksum", strip_info); - return; - } - } - - /*printk(KERN_INFO "%s: Got packet from \"%s\".\n", strip_info->dev->name, sendername); */ - - /* - * Fill in (pseudo) source and destination addresses in the packet. - * We assume that the destination address was our address (the radio does not - * tell us this). If the radio supplies a source address, then we use it. - */ - header.dst_addr = strip_info->true_dev_addr; - string_to_radio_address(&header.src_addr, sendername); - -#ifdef EXT_COUNTERS - if (key.l == SIP0Key.l) { - strip_info->rx_rbytes += (end - ptr); - process_IP_packet(strip_info, &header, ptr, end); - } else if (key.l == ARP0Key.l) { - strip_info->rx_rbytes += (end - ptr); - process_ARP_packet(strip_info, &header, ptr, end); - } else if (key.l == ATR_Key.l) { - strip_info->rx_ebytes += (end - ptr); - process_AT_response(strip_info, ptr, end); - } else if (key.l == ACK_Key.l) { - strip_info->rx_ebytes += (end - ptr); - process_ACK(strip_info, ptr, end); - } else if (key.l == INF_Key.l) { - strip_info->rx_ebytes += (end - ptr); - process_Info(strip_info, ptr, end); - } else if (key.l == ERR_Key.l) { - strip_info->rx_ebytes += (end - ptr); - RecvErr_Message(strip_info, sendername, ptr, end - ptr); - } else - RecvErr("Unrecognized protocol key", strip_info); -#else - if (key.l == SIP0Key.l) - process_IP_packet(strip_info, &header, ptr, end); - else if (key.l == ARP0Key.l) - process_ARP_packet(strip_info, &header, ptr, end); - else if (key.l == ATR_Key.l) - process_AT_response(strip_info, ptr, end); - else if (key.l == ACK_Key.l) - process_ACK(strip_info, ptr, end); - else if (key.l == INF_Key.l) - process_Info(strip_info, ptr, end); - else if (key.l == ERR_Key.l) - RecvErr_Message(strip_info, sendername, ptr, end - ptr); - else - RecvErr("Unrecognized protocol key", strip_info); -#endif -} - -#define TTYERROR(X) ((X) == TTY_BREAK ? "Break" : \ - (X) == TTY_FRAME ? "Framing Error" : \ - (X) == TTY_PARITY ? "Parity Error" : \ - (X) == TTY_OVERRUN ? "Hardware Overrun" : "Unknown Error") - -/* - * Handle the 'receiver data ready' interrupt. - * This function is called by the 'tty_io' module in the kernel when - * a block of STRIP data has been received, which can now be decapsulated - * and sent on to some IP layer for further processing. - */ - -static void strip_receive_buf(struct tty_struct *tty, const unsigned char *cp, - char *fp, int count) -{ - struct strip *strip_info = tty->disc_data; - const unsigned char *end = cp + count; - - if (!strip_info || strip_info->magic != STRIP_MAGIC - || !netif_running(strip_info->dev)) - return; - - spin_lock_bh(&strip_lock); -#if 0 - { - struct timeval tv; - do_gettimeofday(&tv); - printk(KERN_INFO - "**** strip_receive_buf: %3d bytes at %02d.%06d\n", - count, tv.tv_sec % 100, tv.tv_usec); - } -#endif - -#ifdef EXT_COUNTERS - strip_info->rx_sbytes += count; -#endif - - /* Read the characters out of the buffer */ - while (cp < end) { - if (fp && *fp) - printk(KERN_INFO "%s: %s on serial port\n", - strip_info->dev->name, TTYERROR(*fp)); - if (fp && *fp++ && !strip_info->discard) { /* If there's a serial error, record it */ - /* If we have some characters in the buffer, discard them */ - strip_info->discard = strip_info->sx_count; - strip_info->rx_errors++; - } - - /* Leading control characters (CR, NL, Tab, etc.) are ignored */ - if (strip_info->sx_count > 0 || *cp >= ' ') { - if (*cp == 0x0D) { /* If end of packet, decide what to do with it */ - if (strip_info->sx_count > 3000) - printk(KERN_INFO - "%s: Cut a %d byte packet (%zd bytes remaining)%s\n", - strip_info->dev->name, - strip_info->sx_count, - end - cp - 1, - strip_info-> - discard ? " (discarded)" : - ""); - if (strip_info->sx_count > - strip_info->sx_size) { - strip_info->rx_over_errors++; - printk(KERN_INFO - "%s: sx_buff overflow (%d bytes total)\n", - strip_info->dev->name, - strip_info->sx_count); - } else if (strip_info->discard) - printk(KERN_INFO - "%s: Discarding bad packet (%d/%d)\n", - strip_info->dev->name, - strip_info->discard, - strip_info->sx_count); - else - process_message(strip_info); - strip_info->discard = 0; - strip_info->sx_count = 0; - } else { - /* Make sure we have space in the buffer */ - if (strip_info->sx_count < - strip_info->sx_size) - strip_info->sx_buff[strip_info-> - sx_count] = - *cp; - strip_info->sx_count++; - } - } - cp++; - } - spin_unlock_bh(&strip_lock); -} - - -/************************************************************************/ -/* General control routines */ - -static int set_mac_address(struct strip *strip_info, - MetricomAddress * addr) -{ - /* - * We're using a manually specified address if the address is set - * to anything other than all ones. Setting the address to all ones - * disables manual mode and goes back to automatic address determination - * (tracking the true address that the radio has). - */ - strip_info->manual_dev_addr = - memcmp(addr->c, broadcast_address.c, - sizeof(broadcast_address)); - if (strip_info->manual_dev_addr) - *(MetricomAddress *) strip_info->dev->dev_addr = *addr; - else - *(MetricomAddress *) strip_info->dev->dev_addr = - strip_info->true_dev_addr; - return 0; -} - -static int strip_set_mac_address(struct net_device *dev, void *addr) -{ - struct strip *strip_info = netdev_priv(dev); - struct sockaddr *sa = addr; - printk(KERN_INFO "%s: strip_set_dev_mac_address called\n", dev->name); - set_mac_address(strip_info, (MetricomAddress *) sa->sa_data); - return 0; -} - -static struct net_device_stats *strip_get_stats(struct net_device *dev) -{ - struct strip *strip_info = netdev_priv(dev); - static struct net_device_stats stats; - - memset(&stats, 0, sizeof(struct net_device_stats)); - - stats.rx_packets = strip_info->rx_packets; - stats.tx_packets = strip_info->tx_packets; - stats.rx_dropped = strip_info->rx_dropped; - stats.tx_dropped = strip_info->tx_dropped; - stats.tx_errors = strip_info->tx_errors; - stats.rx_errors = strip_info->rx_errors; - stats.rx_over_errors = strip_info->rx_over_errors; - return (&stats); -} - - -/************************************************************************/ -/* Opening and closing */ - -/* - * Here's the order things happen: - * When the user runs "slattach -p strip ..." - * 1. The TTY module calls strip_open;; - * 2. strip_open calls strip_alloc - * 3. strip_alloc calls register_netdev - * 4. register_netdev calls strip_dev_init - * 5. then strip_open finishes setting up the strip_info - * - * When the user runs "ifconfig st<x> up address netmask ..." - * 6. strip_open_low gets called - * - * When the user runs "ifconfig st<x> down" - * 7. strip_close_low gets called - * - * When the user kills the slattach process - * 8. strip_close gets called - * 9. strip_close calls dev_close - * 10. if the device is still up, then dev_close calls strip_close_low - * 11. strip_close calls strip_free - */ - -/* Open the low-level part of the STRIP channel. Easy! */ - -static int strip_open_low(struct net_device *dev) -{ - struct strip *strip_info = netdev_priv(dev); - - if (strip_info->tty == NULL) - return (-ENODEV); - - if (!allocate_buffers(strip_info, dev->mtu)) - return (-ENOMEM); - - strip_info->sx_count = 0; - strip_info->tx_left = 0; - - strip_info->discard = 0; - strip_info->working = FALSE; - strip_info->firmware_level = NoStructure; - strip_info->next_command = CompatibilityCommand; - strip_info->user_baud = tty_get_baud_rate(strip_info->tty); - - printk(KERN_INFO "%s: Initializing Radio.\n", - strip_info->dev->name); - ResetRadio(strip_info); - strip_info->idle_timer.expires = jiffies + 1 * HZ; - add_timer(&strip_info->idle_timer); - netif_wake_queue(dev); - return (0); -} - - -/* - * Close the low-level part of the STRIP channel. Easy! - */ - -static int strip_close_low(struct net_device *dev) -{ - struct strip *strip_info = netdev_priv(dev); - - if (strip_info->tty == NULL) - return -EBUSY; - clear_bit(TTY_DO_WRITE_WAKEUP, &strip_info->tty->flags); - netif_stop_queue(dev); - - /* - * Free all STRIP frame buffers. - */ - kfree(strip_info->rx_buff); - strip_info->rx_buff = NULL; - kfree(strip_info->sx_buff); - strip_info->sx_buff = NULL; - kfree(strip_info->tx_buff); - strip_info->tx_buff = NULL; - - del_timer(&strip_info->idle_timer); - return 0; -} - -static const struct header_ops strip_header_ops = { - .create = strip_header, - .rebuild = strip_rebuild_header, -}; - - -static const struct net_device_ops strip_netdev_ops = { - .ndo_open = strip_open_low, - .ndo_stop = strip_close_low, - .ndo_start_xmit = strip_xmit, - .ndo_set_mac_address = strip_set_mac_address, - .ndo_get_stats = strip_get_stats, - .ndo_change_mtu = strip_change_mtu, -}; - -/* - * This routine is called by DDI when the - * (dynamically assigned) device is registered - */ - -static void strip_dev_setup(struct net_device *dev) -{ - /* - * Finish setting up the DEVICE info. - */ - - dev->trans_start = 0; - dev->tx_queue_len = 30; /* Drop after 30 frames queued */ - - dev->flags = 0; - dev->mtu = DEFAULT_STRIP_MTU; - dev->type = ARPHRD_METRICOM; /* dtang */ - dev->hard_header_len = sizeof(STRIP_Header); - /* - * netdev_priv(dev) Already holds a pointer to our struct strip - */ - - *(MetricomAddress *)dev->broadcast = broadcast_address; - dev->dev_addr[0] = 0; - dev->addr_len = sizeof(MetricomAddress); - - dev->header_ops = &strip_header_ops, - dev->netdev_ops = &strip_netdev_ops; -} - -/* - * Free a STRIP channel. - */ - -static void strip_free(struct strip *strip_info) -{ - spin_lock_bh(&strip_lock); - list_del_rcu(&strip_info->list); - spin_unlock_bh(&strip_lock); - - strip_info->magic = 0; - - free_netdev(strip_info->dev); -} - - -/* - * Allocate a new free STRIP channel - */ -static struct strip *strip_alloc(void) -{ - struct list_head *n; - struct net_device *dev; - struct strip *strip_info; - - dev = alloc_netdev(sizeof(struct strip), "st%d", - strip_dev_setup); - - if (!dev) - return NULL; /* If no more memory, return */ - - - strip_info = netdev_priv(dev); - strip_info->dev = dev; - - strip_info->magic = STRIP_MAGIC; - strip_info->tty = NULL; - - strip_info->gratuitous_arp = jiffies + LongTime; - strip_info->arp_interval = 0; - init_timer(&strip_info->idle_timer); - strip_info->idle_timer.data = (long) dev; - strip_info->idle_timer.function = strip_IdleTask; - - - spin_lock_bh(&strip_lock); - rescan: - /* - * Search the list to find where to put our new entry - * (and in the process decide what channel number it is - * going to be) - */ - list_for_each(n, &strip_list) { - struct strip *s = hlist_entry(n, struct strip, list); - - if (s->dev->base_addr == dev->base_addr) { - ++dev->base_addr; - goto rescan; - } - } - - sprintf(dev->name, "st%ld", dev->base_addr); - - list_add_tail_rcu(&strip_info->list, &strip_list); - spin_unlock_bh(&strip_lock); - - return strip_info; -} - -/* - * Open the high-level part of the STRIP channel. - * This function is called by the TTY module when the - * STRIP line discipline is called for. Because we are - * sure the tty line exists, we only have to link it to - * a free STRIP channel... - */ - -static int strip_open(struct tty_struct *tty) -{ - struct strip *strip_info = tty->disc_data; - - /* - * First make sure we're not already connected. - */ - - if (strip_info && strip_info->magic == STRIP_MAGIC) - return -EEXIST; - - /* - * We need a write method. - */ - - if (tty->ops->write == NULL || tty->ops->set_termios == NULL) - return -EOPNOTSUPP; - - /* - * OK. Find a free STRIP channel to use. - */ - if ((strip_info = strip_alloc()) == NULL) - return -ENFILE; - - /* - * Register our newly created device so it can be ifconfig'd - * strip_dev_init() will be called as a side-effect - */ - - if (register_netdev(strip_info->dev) != 0) { - printk(KERN_ERR "strip: register_netdev() failed.\n"); - strip_free(strip_info); - return -ENFILE; - } - - strip_info->tty = tty; - tty->disc_data = strip_info; - tty->receive_room = 65536; - - tty_driver_flush_buffer(tty); - - /* - * Restore default settings - */ - - strip_info->dev->type = ARPHRD_METRICOM; /* dtang */ - - /* - * Set tty options - */ - - tty->termios->c_iflag |= IGNBRK | IGNPAR; /* Ignore breaks and parity errors. */ - tty->termios->c_cflag |= CLOCAL; /* Ignore modem control signals. */ - tty->termios->c_cflag &= ~HUPCL; /* Don't close on hup */ - - printk(KERN_INFO "STRIP: device \"%s\" activated\n", - strip_info->dev->name); - - /* - * Done. We have linked the TTY line to a channel. - */ - return (strip_info->dev->base_addr); -} - -/* - * Close down a STRIP channel. - * This means flushing out any pending queues, and then restoring the - * TTY line discipline to what it was before it got hooked to STRIP - * (which usually is TTY again). - */ - -static void strip_close(struct tty_struct *tty) -{ - struct strip *strip_info = tty->disc_data; - - /* - * First make sure we're connected. - */ - - if (!strip_info || strip_info->magic != STRIP_MAGIC) - return; - - unregister_netdev(strip_info->dev); - - tty->disc_data = NULL; - strip_info->tty = NULL; - printk(KERN_INFO "STRIP: device \"%s\" closed down\n", - strip_info->dev->name); - strip_free(strip_info); - tty->disc_data = NULL; -} - - -/************************************************************************/ -/* Perform I/O control calls on an active STRIP channel. */ - -static int strip_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - struct strip *strip_info = tty->disc_data; - - /* - * First make sure we're connected. - */ - - if (!strip_info || strip_info->magic != STRIP_MAGIC) - return -EINVAL; - - switch (cmd) { - case SIOCGIFNAME: - if(copy_to_user((void __user *) arg, strip_info->dev->name, strlen(strip_info->dev->name) + 1)) - return -EFAULT; - break; - case SIOCSIFHWADDR: - { - MetricomAddress addr; - //printk(KERN_INFO "%s: SIOCSIFHWADDR\n", strip_info->dev->name); - if(copy_from_user(&addr, (void __user *) arg, sizeof(MetricomAddress))) - return -EFAULT; - return set_mac_address(strip_info, &addr); - } - default: - return tty_mode_ioctl(tty, file, cmd, arg); - break; - } - return 0; -} - -#ifdef CONFIG_COMPAT -static long strip_compat_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - switch (cmd) { - case SIOCGIFNAME: - case SIOCSIFHWADDR: - return strip_ioctl(tty, file, cmd, - (unsigned long)compat_ptr(arg)); - } - return -ENOIOCTLCMD; -} -#endif - -/************************************************************************/ -/* Initialization */ - -static struct tty_ldisc_ops strip_ldisc = { - .magic = TTY_LDISC_MAGIC, - .name = "strip", - .owner = THIS_MODULE, - .open = strip_open, - .close = strip_close, - .ioctl = strip_ioctl, -#ifdef CONFIG_COMPAT - .compat_ioctl = strip_compat_ioctl, -#endif - .receive_buf = strip_receive_buf, - .write_wakeup = strip_write_some_more, -}; - -/* - * Initialize the STRIP driver. - * This routine is called at boot time, to bootstrap the multi-channel - * STRIP driver - */ - -static char signon[] __initdata = - KERN_INFO "STRIP: Version %s (unlimited channels)\n"; - -static int __init strip_init_driver(void) -{ - int status; - - printk(signon, StripVersion); - - - /* - * Fill in our line protocol discipline, and register it - */ - if ((status = tty_register_ldisc(N_STRIP, &strip_ldisc))) - printk(KERN_ERR "STRIP: can't register line discipline (err = %d)\n", - status); - - /* - * Register the status file with /proc - */ - proc_net_fops_create(&init_net, "strip", S_IFREG | S_IRUGO, &strip_seq_fops); - - return status; -} - -module_init(strip_init_driver); - -static const char signoff[] __exitdata = - KERN_INFO "STRIP: Module Unloaded\n"; - -static void __exit strip_exit_driver(void) -{ - int i; - struct list_head *p,*n; - - /* module ref count rules assure that all entries are unregistered */ - list_for_each_safe(p, n, &strip_list) { - struct strip *s = list_entry(p, struct strip, list); - strip_free(s); - } - - /* Unregister with the /proc/net file here. */ - proc_net_remove(&init_net, "strip"); - - if ((i = tty_unregister_ldisc(N_STRIP))) - printk(KERN_ERR "STRIP: can't unregister line discipline (err = %d)\n", i); - - printk(signoff); -} - -module_exit(strip_exit_driver); - -MODULE_AUTHOR("Stuart Cheshire <cheshire@cs.stanford.edu>"); -MODULE_DESCRIPTION("Starmode Radio IP (STRIP) Device Driver"); -MODULE_LICENSE("Dual BSD/GPL"); - -MODULE_SUPPORTED_DEVICE("Starmode Radio IP (STRIP) modem"); diff --git a/drivers/net/wireless/wavelan.c b/drivers/net/wireless/wavelan.c deleted file mode 100644 index d634b2d..0000000 --- a/drivers/net/wireless/wavelan.c +++ /dev/null @@ -1,4383 +0,0 @@ -/* - * WaveLAN ISA driver - * - * Jean II - HPLB '96 - * - * Reorganisation and extension of the driver. - * Original copyright follows (also see the end of this file). - * See wavelan.p.h for details. - * - * - * - * AT&T GIS (nee NCR) WaveLAN card: - * An Ethernet-like radio transceiver - * controlled by an Intel 82586 coprocessor. - */ - -#include "wavelan.p.h" /* Private header */ - -/************************* MISC SUBROUTINES **************************/ -/* - * Subroutines which won't fit in one of the following category - * (WaveLAN modem or i82586) - */ - -/*------------------------------------------------------------------*/ -/* - * Translate irq number to PSA irq parameter - */ -static u8 wv_irq_to_psa(int irq) -{ - if (irq < 0 || irq >= ARRAY_SIZE(irqvals)) - return 0; - - return irqvals[irq]; -} - -/*------------------------------------------------------------------*/ -/* - * Translate PSA irq parameter to irq number - */ -static int __init wv_psa_to_irq(u8 irqval) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(irqvals); i++) - if (irqvals[i] == irqval) - return i; - - return -1; -} - -/********************* HOST ADAPTER SUBROUTINES *********************/ -/* - * Useful subroutines to manage the WaveLAN ISA interface - * - * One major difference with the PCMCIA hardware (except the port mapping) - * is that we have to keep the state of the Host Control Register - * because of the interrupt enable & bus size flags. - */ - -/*------------------------------------------------------------------*/ -/* - * Read from card's Host Adaptor Status Register. - */ -static inline u16 hasr_read(unsigned long ioaddr) -{ - return (inw(HASR(ioaddr))); -} /* hasr_read */ - -/*------------------------------------------------------------------*/ -/* - * Write to card's Host Adapter Command Register. - */ -static inline void hacr_write(unsigned long ioaddr, u16 hacr) -{ - outw(hacr, HACR(ioaddr)); -} /* hacr_write */ - -/*------------------------------------------------------------------*/ -/* - * Write to card's Host Adapter Command Register. Include a delay for - * those times when it is needed. - */ -static void hacr_write_slow(unsigned long ioaddr, u16 hacr) -{ - hacr_write(ioaddr, hacr); - /* delay might only be needed sometimes */ - mdelay(1); -} /* hacr_write_slow */ - -/*------------------------------------------------------------------*/ -/* - * Set the channel attention bit. - */ -static inline void set_chan_attn(unsigned long ioaddr, u16 hacr) -{ - hacr_write(ioaddr, hacr | HACR_CA); -} /* set_chan_attn */ - -/*------------------------------------------------------------------*/ -/* - * Reset, and then set host adaptor into default mode. - */ -static inline void wv_hacr_reset(unsigned long ioaddr) -{ - hacr_write_slow(ioaddr, HACR_RESET); - hacr_write(ioaddr, HACR_DEFAULT); -} /* wv_hacr_reset */ - -/*------------------------------------------------------------------*/ -/* - * Set the I/O transfer over the ISA bus to 8-bit mode - */ -static inline void wv_16_off(unsigned long ioaddr, u16 hacr) -{ - hacr &= ~HACR_16BITS; - hacr_write(ioaddr, hacr); -} /* wv_16_off */ - -/*------------------------------------------------------------------*/ -/* - * Set the I/O transfer over the ISA bus to 8-bit mode - */ -static inline void wv_16_on(unsigned long ioaddr, u16 hacr) -{ - hacr |= HACR_16BITS; - hacr_write(ioaddr, hacr); -} /* wv_16_on */ - -/*------------------------------------------------------------------*/ -/* - * Disable interrupts on the WaveLAN hardware. - * (called by wv_82586_stop()) - */ -static inline void wv_ints_off(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - - lp->hacr &= ~HACR_INTRON; - hacr_write(ioaddr, lp->hacr); -} /* wv_ints_off */ - -/*------------------------------------------------------------------*/ -/* - * Enable interrupts on the WaveLAN hardware. - * (called by wv_hw_reset()) - */ -static inline void wv_ints_on(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - - lp->hacr |= HACR_INTRON; - hacr_write(ioaddr, lp->hacr); -} /* wv_ints_on */ - -/******************* MODEM MANAGEMENT SUBROUTINES *******************/ -/* - * Useful subroutines to manage the modem of the WaveLAN - */ - -/*------------------------------------------------------------------*/ -/* - * Read the Parameter Storage Area from the WaveLAN card's memory - */ -/* - * Read bytes from the PSA. - */ -static void psa_read(unsigned long ioaddr, u16 hacr, int o, /* offset in PSA */ - u8 * b, /* buffer to fill */ - int n) -{ /* size to read */ - wv_16_off(ioaddr, hacr); - - while (n-- > 0) { - outw(o, PIOR2(ioaddr)); - o++; - *b++ = inb(PIOP2(ioaddr)); - } - - wv_16_on(ioaddr, hacr); -} /* psa_read */ - -/*------------------------------------------------------------------*/ -/* - * Write the Parameter Storage Area to the WaveLAN card's memory. - */ -static void psa_write(unsigned long ioaddr, u16 hacr, int o, /* Offset in PSA */ - u8 * b, /* Buffer in memory */ - int n) -{ /* Length of buffer */ - int count = 0; - - wv_16_off(ioaddr, hacr); - - while (n-- > 0) { - outw(o, PIOR2(ioaddr)); - o++; - - outb(*b, PIOP2(ioaddr)); - b++; - - /* Wait for the memory to finish its write cycle */ - count = 0; - while ((count++ < 100) && - (hasr_read(ioaddr) & HASR_PSA_BUSY)) mdelay(1); - } - - wv_16_on(ioaddr, hacr); -} /* psa_write */ - -#ifdef SET_PSA_CRC -/*------------------------------------------------------------------*/ -/* - * Calculate the PSA CRC - * Thanks to Valster, Nico <NVALSTER@wcnd.nl.lucent.com> for the code - * NOTE: By specifying a length including the CRC position the - * returned value should be zero. (i.e. a correct checksum in the PSA) - * - * The Windows drivers don't use the CRC, but the AP and the PtP tool - * depend on it. - */ -static u16 psa_crc(u8 * psa, /* The PSA */ - int size) -{ /* Number of short for CRC */ - int byte_cnt; /* Loop on the PSA */ - u16 crc_bytes = 0; /* Data in the PSA */ - int bit_cnt; /* Loop on the bits of the short */ - - for (byte_cnt = 0; byte_cnt < size; byte_cnt++) { - crc_bytes ^= psa[byte_cnt]; /* Its an xor */ - - for (bit_cnt = 1; bit_cnt < 9; bit_cnt++) { - if (crc_bytes & 0x0001) - crc_bytes = (crc_bytes >> 1) ^ 0xA001; - else - crc_bytes >>= 1; - } - } - - return crc_bytes; -} /* psa_crc */ -#endif /* SET_PSA_CRC */ - -/*------------------------------------------------------------------*/ -/* - * update the checksum field in the Wavelan's PSA - */ -static void update_psa_checksum(struct net_device * dev, unsigned long ioaddr, u16 hacr) -{ -#ifdef SET_PSA_CRC - psa_t psa; - u16 crc; - - /* read the parameter storage area */ - psa_read(ioaddr, hacr, 0, (unsigned char *) &psa, sizeof(psa)); - - /* update the checksum */ - crc = psa_crc((unsigned char *) &psa, - sizeof(psa) - sizeof(psa.psa_crc[0]) - - sizeof(psa.psa_crc[1]) - - sizeof(psa.psa_crc_status)); - - psa.psa_crc[0] = crc & 0xFF; - psa.psa_crc[1] = (crc & 0xFF00) >> 8; - - /* Write it ! */ - psa_write(ioaddr, hacr, (char *) &psa.psa_crc - (char *) &psa, - (unsigned char *) &psa.psa_crc, 2); - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "%s: update_psa_checksum(): crc = 0x%02x%02x\n", - dev->name, psa.psa_crc[0], psa.psa_crc[1]); - - /* Check again (luxury !) */ - crc = psa_crc((unsigned char *) &psa, - sizeof(psa) - sizeof(psa.psa_crc_status)); - - if (crc != 0) - printk(KERN_WARNING - "%s: update_psa_checksum(): CRC does not agree with PSA data (even after recalculating)\n", - dev->name); -#endif /* DEBUG_IOCTL_INFO */ -#endif /* SET_PSA_CRC */ -} /* update_psa_checksum */ - -/*------------------------------------------------------------------*/ -/* - * Write 1 byte to the MMC. - */ -static void mmc_out(unsigned long ioaddr, u16 o, u8 d) -{ - int count = 0; - - /* Wait for MMC to go idle */ - while ((count++ < 100) && (inw(HASR(ioaddr)) & HASR_MMC_BUSY)) - udelay(10); - - outw((u16) (((u16) d << 8) | (o << 1) | 1), MMCR(ioaddr)); -} - -/*------------------------------------------------------------------*/ -/* - * Routine to write bytes to the Modem Management Controller. - * We start at the end because it is the way it should be! - */ -static void mmc_write(unsigned long ioaddr, u8 o, u8 * b, int n) -{ - o += n; - b += n; - - while (n-- > 0) - mmc_out(ioaddr, --o, *(--b)); -} /* mmc_write */ - -/*------------------------------------------------------------------*/ -/* - * Read a byte from the MMC. - * Optimised version for 1 byte, avoid using memory. - */ -static u8 mmc_in(unsigned long ioaddr, u16 o) -{ - int count = 0; - - while ((count++ < 100) && (inw(HASR(ioaddr)) & HASR_MMC_BUSY)) - udelay(10); - outw(o << 1, MMCR(ioaddr)); - - while ((count++ < 100) && (inw(HASR(ioaddr)) & HASR_MMC_BUSY)) - udelay(10); - return (u8) (inw(MMCR(ioaddr)) >> 8); -} - -/*------------------------------------------------------------------*/ -/* - * Routine to read bytes from the Modem Management Controller. - * The implementation is complicated by a lack of address lines, - * which prevents decoding of the low-order bit. - * (code has just been moved in the above function) - * We start at the end because it is the way it should be! - */ -static inline void mmc_read(unsigned long ioaddr, u8 o, u8 * b, int n) -{ - o += n; - b += n; - - while (n-- > 0) - *(--b) = mmc_in(ioaddr, --o); -} /* mmc_read */ - -/*------------------------------------------------------------------*/ -/* - * Get the type of encryption available. - */ -static inline int mmc_encr(unsigned long ioaddr) -{ /* I/O port of the card */ - int temp; - - temp = mmc_in(ioaddr, mmroff(0, mmr_des_avail)); - if ((temp != MMR_DES_AVAIL_DES) && (temp != MMR_DES_AVAIL_AES)) - return 0; - else - return temp; -} - -/*------------------------------------------------------------------*/ -/* - * Wait for the frequency EEPROM to complete a command. - * I hope this one will be optimally inlined. - */ -static inline void fee_wait(unsigned long ioaddr, /* I/O port of the card */ - int delay, /* Base delay to wait for */ - int number) -{ /* Number of time to wait */ - int count = 0; /* Wait only a limited time */ - - while ((count++ < number) && - (mmc_in(ioaddr, mmroff(0, mmr_fee_status)) & - MMR_FEE_STATUS_BUSY)) udelay(delay); -} - -/*------------------------------------------------------------------*/ -/* - * Read bytes from the Frequency EEPROM (frequency select cards). - */ -static void fee_read(unsigned long ioaddr, /* I/O port of the card */ - u16 o, /* destination offset */ - u16 * b, /* data buffer */ - int n) -{ /* number of registers */ - b += n; /* Position at the end of the area */ - - /* Write the address */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), o + n - 1); - - /* Loop on all buffer */ - while (n-- > 0) { - /* Write the read command */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), - MMW_FEE_CTRL_READ); - - /* Wait until EEPROM is ready (should be quick). */ - fee_wait(ioaddr, 10, 100); - - /* Read the value. */ - *--b = ((mmc_in(ioaddr, mmroff(0, mmr_fee_data_h)) << 8) | - mmc_in(ioaddr, mmroff(0, mmr_fee_data_l))); - } -} - - -/*------------------------------------------------------------------*/ -/* - * Write bytes from the Frequency EEPROM (frequency select cards). - * This is a bit complicated, because the frequency EEPROM has to - * be unprotected and the write enabled. - * Jean II - */ -static void fee_write(unsigned long ioaddr, /* I/O port of the card */ - u16 o, /* destination offset */ - u16 * b, /* data buffer */ - int n) -{ /* number of registers */ - b += n; /* Position at the end of the area. */ - -#ifdef EEPROM_IS_PROTECTED /* disabled */ -#ifdef DOESNT_SEEM_TO_WORK /* disabled */ - /* Ask to read the protected register */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRREAD); - - fee_wait(ioaddr, 10, 100); - - /* Read the protected register. */ - printk("Protected 2: %02X-%02X\n", - mmc_in(ioaddr, mmroff(0, mmr_fee_data_h)), - mmc_in(ioaddr, mmroff(0, mmr_fee_data_l))); -#endif /* DOESNT_SEEM_TO_WORK */ - - /* Enable protected register. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_EN); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PREN); - - fee_wait(ioaddr, 10, 100); - - /* Unprotect area. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), o + n); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRWRITE); -#ifdef DOESNT_SEEM_TO_WORK /* disabled */ - /* or use: */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRCLEAR); -#endif /* DOESNT_SEEM_TO_WORK */ - - fee_wait(ioaddr, 10, 100); -#endif /* EEPROM_IS_PROTECTED */ - - /* Write enable. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_EN); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WREN); - - fee_wait(ioaddr, 10, 100); - - /* Write the EEPROM address. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), o + n - 1); - - /* Loop on all buffer */ - while (n-- > 0) { - /* Write the value. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_data_h), (*--b) >> 8); - mmc_out(ioaddr, mmwoff(0, mmw_fee_data_l), *b & 0xFF); - - /* Write the write command. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), - MMW_FEE_CTRL_WRITE); - - /* WaveLAN documentation says to wait at least 10 ms for EEBUSY = 0 */ - mdelay(10); - fee_wait(ioaddr, 10, 100); - } - - /* Write disable. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_DS); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WDS); - - fee_wait(ioaddr, 10, 100); - -#ifdef EEPROM_IS_PROTECTED /* disabled */ - /* Reprotect EEPROM. */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), 0x00); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRWRITE); - - fee_wait(ioaddr, 10, 100); -#endif /* EEPROM_IS_PROTECTED */ -} - -/************************ I82586 SUBROUTINES *************************/ -/* - * Useful subroutines to manage the Ethernet controller - */ - -/*------------------------------------------------------------------*/ -/* - * Read bytes from the on-board RAM. - * Why does inlining this function make it fail? - */ -static /*inline */ void obram_read(unsigned long ioaddr, - u16 o, u8 * b, int n) -{ - outw(o, PIOR1(ioaddr)); - insw(PIOP1(ioaddr), (unsigned short *) b, (n + 1) >> 1); -} - -/*------------------------------------------------------------------*/ -/* - * Write bytes to the on-board RAM. - */ -static inline void obram_write(unsigned long ioaddr, u16 o, u8 * b, int n) -{ - outw(o, PIOR1(ioaddr)); - outsw(PIOP1(ioaddr), (unsigned short *) b, (n + 1) >> 1); -} - -/*------------------------------------------------------------------*/ -/* - * Acknowledge the reading of the status issued by the i82586. - */ -static void wv_ack(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - u16 scb_cs; - int i; - - obram_read(ioaddr, scboff(OFFSET_SCB, scb_status), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - scb_cs &= SCB_ST_INT; - - if (scb_cs == 0) - return; - - obram_write(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - - set_chan_attn(ioaddr, lp->hacr); - - for (i = 1000; i > 0; i--) { - obram_read(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - if (scb_cs == 0) - break; - - udelay(10); - } - udelay(100); - -#ifdef DEBUG_CONFIG_ERROR - if (i <= 0) - printk(KERN_INFO - "%s: wv_ack(): board not accepting command.\n", - dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * Set channel attention bit and busy wait until command has - * completed, then acknowledge completion of the command. - */ -static int wv_synchronous_cmd(struct net_device * dev, const char *str) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - u16 scb_cmd; - ach_t cb; - int i; - - scb_cmd = SCB_CMD_CUC & SCB_CMD_CUC_GO; - obram_write(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cmd, sizeof(scb_cmd)); - - set_chan_attn(ioaddr, lp->hacr); - - for (i = 1000; i > 0; i--) { - obram_read(ioaddr, OFFSET_CU, (unsigned char *) &cb, - sizeof(cb)); - if (cb.ac_status & AC_SFLD_C) - break; - - udelay(10); - } - udelay(100); - - if (i <= 0 || !(cb.ac_status & AC_SFLD_OK)) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO "%s: %s failed; status = 0x%x\n", - dev->name, str, cb.ac_status); -#endif -#ifdef DEBUG_I82586_SHOW - wv_scb_show(ioaddr); -#endif - return -1; - } - - /* Ack the status */ - wv_ack(dev); - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Configuration commands completion interrupt. - * Check if done, and if OK. - */ -static int -wv_config_complete(struct net_device * dev, unsigned long ioaddr, net_local * lp) -{ - unsigned short mcs_addr; - unsigned short status; - int ret; - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: ->wv_config_complete()\n", dev->name); -#endif - - mcs_addr = lp->tx_first_in_use + sizeof(ac_tx_t) + sizeof(ac_nop_t) - + sizeof(tbd_t) + sizeof(ac_cfg_t) + sizeof(ac_ias_t); - - /* Read the status of the last command (set mc list). */ - obram_read(ioaddr, acoff(mcs_addr, ac_status), - (unsigned char *) &status, sizeof(status)); - - /* If not completed -> exit */ - if ((status & AC_SFLD_C) == 0) - ret = 0; /* Not ready to be scrapped */ - else { -#ifdef DEBUG_CONFIG_ERROR - unsigned short cfg_addr; - unsigned short ias_addr; - - /* Check mc_config command */ - if ((status & AC_SFLD_OK) != AC_SFLD_OK) - printk(KERN_INFO - "%s: wv_config_complete(): set_multicast_address failed; status = 0x%x\n", - dev->name, status); - - /* check ia-config command */ - ias_addr = mcs_addr - sizeof(ac_ias_t); - obram_read(ioaddr, acoff(ias_addr, ac_status), - (unsigned char *) &status, sizeof(status)); - if ((status & AC_SFLD_OK) != AC_SFLD_OK) - printk(KERN_INFO - "%s: wv_config_complete(): set_MAC_address failed; status = 0x%x\n", - dev->name, status); - - /* Check config command. */ - cfg_addr = ias_addr - sizeof(ac_cfg_t); - obram_read(ioaddr, acoff(cfg_addr, ac_status), - (unsigned char *) &status, sizeof(status)); - if ((status & AC_SFLD_OK) != AC_SFLD_OK) - printk(KERN_INFO - "%s: wv_config_complete(): configure failed; status = 0x%x\n", - dev->name, status); -#endif /* DEBUG_CONFIG_ERROR */ - - ret = 1; /* Ready to be scrapped */ - } - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: <-wv_config_complete() - %d\n", dev->name, - ret); -#endif - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Command completion interrupt. - * Reclaim as many freed tx buffers as we can. - * (called in wavelan_interrupt()). - * Note : the spinlock is already grabbed for us. - */ -static int wv_complete(struct net_device * dev, unsigned long ioaddr, net_local * lp) -{ - int nreaped = 0; - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: ->wv_complete()\n", dev->name); -#endif - - /* Loop on all the transmit buffers */ - while (lp->tx_first_in_use != I82586NULL) { - unsigned short tx_status; - - /* Read the first transmit buffer */ - obram_read(ioaddr, acoff(lp->tx_first_in_use, ac_status), - (unsigned char *) &tx_status, - sizeof(tx_status)); - - /* If not completed -> exit */ - if ((tx_status & AC_SFLD_C) == 0) - break; - - /* Hack for reconfiguration */ - if (tx_status == 0xFFFF) - if (!wv_config_complete(dev, ioaddr, lp)) - break; /* Not completed */ - - /* We now remove this buffer */ - nreaped++; - --lp->tx_n_in_use; - -/* -if (lp->tx_n_in_use > 0) - printk("%c", "0123456789abcdefghijk"[lp->tx_n_in_use]); -*/ - - /* Was it the last one? */ - if (lp->tx_n_in_use <= 0) - lp->tx_first_in_use = I82586NULL; - else { - /* Next one in the chain */ - lp->tx_first_in_use += TXBLOCKZ; - if (lp->tx_first_in_use >= - OFFSET_CU + - NTXBLOCKS * TXBLOCKZ) lp->tx_first_in_use -= - NTXBLOCKS * TXBLOCKZ; - } - - /* Hack for reconfiguration */ - if (tx_status == 0xFFFF) - continue; - - /* Now, check status of the finished command */ - if (tx_status & AC_SFLD_OK) { - int ncollisions; - - dev->stats.tx_packets++; - ncollisions = tx_status & AC_SFLD_MAXCOL; - dev->stats.collisions += ncollisions; -#ifdef DEBUG_TX_INFO - if (ncollisions > 0) - printk(KERN_DEBUG - "%s: wv_complete(): tx completed after %d collisions.\n", - dev->name, ncollisions); -#endif - } else { - dev->stats.tx_errors++; - if (tx_status & AC_SFLD_S10) { - dev->stats.tx_carrier_errors++; -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG - "%s: wv_complete(): tx error: no CS.\n", - dev->name); -#endif - } - if (tx_status & AC_SFLD_S9) { - dev->stats.tx_carrier_errors++; -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG - "%s: wv_complete(): tx error: lost CTS.\n", - dev->name); -#endif - } - if (tx_status & AC_SFLD_S8) { - dev->stats.tx_fifo_errors++; -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG - "%s: wv_complete(): tx error: slow DMA.\n", - dev->name); -#endif - } - if (tx_status & AC_SFLD_S6) { - dev->stats.tx_heartbeat_errors++; -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG - "%s: wv_complete(): tx error: heart beat.\n", - dev->name); -#endif - } - if (tx_status & AC_SFLD_S5) { - dev->stats.tx_aborted_errors++; -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG - "%s: wv_complete(): tx error: too many collisions.\n", - dev->name); -#endif - } - } - -#ifdef DEBUG_TX_INFO - printk(KERN_DEBUG - "%s: wv_complete(): tx completed, tx_status 0x%04x\n", - dev->name, tx_status); -#endif - } - -#ifdef DEBUG_INTERRUPT_INFO - if (nreaped > 1) - printk(KERN_DEBUG "%s: wv_complete(): reaped %d\n", - dev->name, nreaped); -#endif - - /* - * Inform upper layers. - */ - if (lp->tx_n_in_use < NTXBLOCKS - 1) { - netif_wake_queue(dev); - } -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: <-wv_complete()\n", dev->name); -#endif - return nreaped; -} - -/*------------------------------------------------------------------*/ -/* - * Reconfigure the i82586, or at least ask for it. - * Because wv_82586_config uses a transmission buffer, we must do it - * when we are sure that there is one left, so we do it now - * or in wavelan_packet_xmit() (I can't find any better place, - * wavelan_interrupt is not an option), so you may experience - * delays sometimes. - */ -static void wv_82586_reconfig(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - - /* Arm the flag, will be cleard in wv_82586_config() */ - lp->reconfig_82586 = 1; - - /* Check if we can do it now ! */ - if((netif_running(dev)) && !(netif_queue_stopped(dev))) { - spin_lock_irqsave(&lp->spinlock, flags); - /* May fail */ - wv_82586_config(dev); - spin_unlock_irqrestore(&lp->spinlock, flags); - } - else { -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG - "%s: wv_82586_reconfig(): delayed (state = %lX)\n", - dev->name, dev->state); -#endif - } -} - -/********************* DEBUG & INFO SUBROUTINES *********************/ -/* - * This routine is used in the code to show information for debugging. - * Most of the time, it dumps the contents of hardware structures. - */ - -#ifdef DEBUG_PSA_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted contents of the Parameter Storage Area. - */ -static void wv_psa_show(psa_t * p) -{ - printk(KERN_DEBUG "##### WaveLAN PSA contents: #####\n"); - printk(KERN_DEBUG "psa_io_base_addr_1: 0x%02X %02X %02X %02X\n", - p->psa_io_base_addr_1, - p->psa_io_base_addr_2, - p->psa_io_base_addr_3, p->psa_io_base_addr_4); - printk(KERN_DEBUG "psa_rem_boot_addr_1: 0x%02X %02X %02X\n", - p->psa_rem_boot_addr_1, - p->psa_rem_boot_addr_2, p->psa_rem_boot_addr_3); - printk(KERN_DEBUG "psa_holi_params: 0x%02x, ", p->psa_holi_params); - printk("psa_int_req_no: %d\n", p->psa_int_req_no); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "psa_unused0[]: %pM\n", p->psa_unused0); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "psa_univ_mac_addr[]: %pM\n", p->psa_univ_mac_addr); - printk(KERN_DEBUG "psa_local_mac_addr[]: %pM\n", p->psa_local_mac_addr); - printk(KERN_DEBUG "psa_univ_local_sel: %d, ", - p->psa_univ_local_sel); - printk("psa_comp_number: %d, ", p->psa_comp_number); - printk("psa_thr_pre_set: 0x%02x\n", p->psa_thr_pre_set); - printk(KERN_DEBUG "psa_feature_select/decay_prm: 0x%02x, ", - p->psa_feature_select); - printk("psa_subband/decay_update_prm: %d\n", p->psa_subband); - printk(KERN_DEBUG "psa_quality_thr: 0x%02x, ", p->psa_quality_thr); - printk("psa_mod_delay: 0x%02x\n", p->psa_mod_delay); - printk(KERN_DEBUG "psa_nwid: 0x%02x%02x, ", p->psa_nwid[0], - p->psa_nwid[1]); - printk("psa_nwid_select: %d\n", p->psa_nwid_select); - printk(KERN_DEBUG "psa_encryption_select: %d, ", - p->psa_encryption_select); - printk - ("psa_encryption_key[]: %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n", - p->psa_encryption_key[0], p->psa_encryption_key[1], - p->psa_encryption_key[2], p->psa_encryption_key[3], - p->psa_encryption_key[4], p->psa_encryption_key[5], - p->psa_encryption_key[6], p->psa_encryption_key[7]); - printk(KERN_DEBUG "psa_databus_width: %d\n", p->psa_databus_width); - printk(KERN_DEBUG "psa_call_code/auto_squelch: 0x%02x, ", - p->psa_call_code[0]); - printk - ("psa_call_code[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n", - p->psa_call_code[0], p->psa_call_code[1], p->psa_call_code[2], - p->psa_call_code[3], p->psa_call_code[4], p->psa_call_code[5], - p->psa_call_code[6], p->psa_call_code[7]); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "psa_reserved[]: %02X:%02X\n", - p->psa_reserved[0], - p->psa_reserved[1]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "psa_conf_status: %d, ", p->psa_conf_status); - printk("psa_crc: 0x%02x%02x, ", p->psa_crc[0], p->psa_crc[1]); - printk("psa_crc_status: 0x%02x\n", p->psa_crc_status); -} /* wv_psa_show */ -#endif /* DEBUG_PSA_SHOW */ - -#ifdef DEBUG_MMC_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the Modem Management Controller. - * This function needs to be completed. - */ -static void wv_mmc_show(struct net_device * dev) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); - mmr_t m; - - /* Basic check */ - if (hasr_read(ioaddr) & HASR_NO_CLK) { - printk(KERN_WARNING - "%s: wv_mmc_show: modem not connected\n", - dev->name); - return; - } - - /* Read the mmc */ - mmc_out(ioaddr, mmwoff(0, mmw_freeze), 1); - mmc_read(ioaddr, 0, (u8 *) & m, sizeof(m)); - mmc_out(ioaddr, mmwoff(0, mmw_freeze), 0); - - /* Don't forget to update statistics */ - lp->wstats.discard.nwid += - (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l; - - printk(KERN_DEBUG "##### WaveLAN modem status registers: #####\n"); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG - "mmc_unused0[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n", - m.mmr_unused0[0], m.mmr_unused0[1], m.mmr_unused0[2], - m.mmr_unused0[3], m.mmr_unused0[4], m.mmr_unused0[5], - m.mmr_unused0[6], m.mmr_unused0[7]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "Encryption algorithm: %02X - Status: %02X\n", - m.mmr_des_avail, m.mmr_des_status); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "mmc_unused1[]: %02X:%02X:%02X:%02X:%02X\n", - m.mmr_unused1[0], - m.mmr_unused1[1], - m.mmr_unused1[2], m.mmr_unused1[3], m.mmr_unused1[4]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "dce_status: 0x%x [%s%s%s%s]\n", - m.mmr_dce_status, - (m. - mmr_dce_status & MMR_DCE_STATUS_RX_BUSY) ? - "energy detected," : "", - (m. - mmr_dce_status & MMR_DCE_STATUS_LOOPT_IND) ? - "loop test indicated," : "", - (m. - mmr_dce_status & MMR_DCE_STATUS_TX_BUSY) ? - "transmitter on," : "", - (m. - mmr_dce_status & MMR_DCE_STATUS_JBR_EXPIRED) ? - "jabber timer expired," : ""); - printk(KERN_DEBUG "Dsp ID: %02X\n", m.mmr_dsp_id); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "mmc_unused2[]: %02X:%02X\n", - m.mmr_unused2[0], m.mmr_unused2[1]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "# correct_nwid: %d, # wrong_nwid: %d\n", - (m.mmr_correct_nwid_h << 8) | m.mmr_correct_nwid_l, - (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l); - printk(KERN_DEBUG "thr_pre_set: 0x%x [current signal %s]\n", - m.mmr_thr_pre_set & MMR_THR_PRE_SET, - (m. - mmr_thr_pre_set & MMR_THR_PRE_SET_CUR) ? "above" : - "below"); - printk(KERN_DEBUG "signal_lvl: %d [%s], ", - m.mmr_signal_lvl & MMR_SIGNAL_LVL, - (m. - mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) ? "new msg" : - "no new msg"); - printk("silence_lvl: %d [%s], ", - m.mmr_silence_lvl & MMR_SILENCE_LVL, - (m. - mmr_silence_lvl & MMR_SILENCE_LVL_VALID) ? "update done" : - "no new update"); - printk("sgnl_qual: 0x%x [%s]\n", m.mmr_sgnl_qual & MMR_SGNL_QUAL, - (m. - mmr_sgnl_qual & MMR_SGNL_QUAL_ANT) ? "Antenna 1" : - "Antenna 0"); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "netw_id_l: %x\n", m.mmr_netw_id_l); -#endif /* DEBUG_SHOW_UNUSED */ -} /* wv_mmc_show */ -#endif /* DEBUG_MMC_SHOW */ - -#ifdef DEBUG_I82586_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the last block of the i82586 memory. - */ -static void wv_scb_show(unsigned long ioaddr) -{ - scb_t scb; - - obram_read(ioaddr, OFFSET_SCB, (unsigned char *) &scb, - sizeof(scb)); - - printk(KERN_DEBUG "##### WaveLAN system control block: #####\n"); - - printk(KERN_DEBUG "status: "); - printk("stat 0x%x[%s%s%s%s] ", - (scb. - scb_status & (SCB_ST_CX | SCB_ST_FR | SCB_ST_CNA | - SCB_ST_RNR)) >> 12, - (scb. - scb_status & SCB_ST_CX) ? "command completion interrupt," : - "", (scb.scb_status & SCB_ST_FR) ? "frame received," : "", - (scb. - scb_status & SCB_ST_CNA) ? "command unit not active," : "", - (scb. - scb_status & SCB_ST_RNR) ? "receiving unit not ready," : - ""); - printk("cus 0x%x[%s%s%s] ", (scb.scb_status & SCB_ST_CUS) >> 8, - ((scb.scb_status & SCB_ST_CUS) == - SCB_ST_CUS_IDLE) ? "idle" : "", - ((scb.scb_status & SCB_ST_CUS) == - SCB_ST_CUS_SUSP) ? "suspended" : "", - ((scb.scb_status & SCB_ST_CUS) == - SCB_ST_CUS_ACTV) ? "active" : ""); - printk("rus 0x%x[%s%s%s%s]\n", (scb.scb_status & SCB_ST_RUS) >> 4, - ((scb.scb_status & SCB_ST_RUS) == - SCB_ST_RUS_IDLE) ? "idle" : "", - ((scb.scb_status & SCB_ST_RUS) == - SCB_ST_RUS_SUSP) ? "suspended" : "", - ((scb.scb_status & SCB_ST_RUS) == - SCB_ST_RUS_NRES) ? "no resources" : "", - ((scb.scb_status & SCB_ST_RUS) == - SCB_ST_RUS_RDY) ? "ready" : ""); - - printk(KERN_DEBUG "command: "); - printk("ack 0x%x[%s%s%s%s] ", - (scb. - scb_command & (SCB_CMD_ACK_CX | SCB_CMD_ACK_FR | - SCB_CMD_ACK_CNA | SCB_CMD_ACK_RNR)) >> 12, - (scb. - scb_command & SCB_CMD_ACK_CX) ? "ack cmd completion," : "", - (scb. - scb_command & SCB_CMD_ACK_FR) ? "ack frame received," : "", - (scb. - scb_command & SCB_CMD_ACK_CNA) ? "ack CU not active," : "", - (scb. - scb_command & SCB_CMD_ACK_RNR) ? "ack RU not ready," : ""); - printk("cuc 0x%x[%s%s%s%s%s] ", - (scb.scb_command & SCB_CMD_CUC) >> 8, - ((scb.scb_command & SCB_CMD_CUC) == - SCB_CMD_CUC_NOP) ? "nop" : "", - ((scb.scb_command & SCB_CMD_CUC) == - SCB_CMD_CUC_GO) ? "start cbl_offset" : "", - ((scb.scb_command & SCB_CMD_CUC) == - SCB_CMD_CUC_RES) ? "resume execution" : "", - ((scb.scb_command & SCB_CMD_CUC) == - SCB_CMD_CUC_SUS) ? "suspend execution" : "", - ((scb.scb_command & SCB_CMD_CUC) == - SCB_CMD_CUC_ABT) ? "abort execution" : ""); - printk("ruc 0x%x[%s%s%s%s%s]\n", - (scb.scb_command & SCB_CMD_RUC) >> 4, - ((scb.scb_command & SCB_CMD_RUC) == - SCB_CMD_RUC_NOP) ? "nop" : "", - ((scb.scb_command & SCB_CMD_RUC) == - SCB_CMD_RUC_GO) ? "start rfa_offset" : "", - ((scb.scb_command & SCB_CMD_RUC) == - SCB_CMD_RUC_RES) ? "resume reception" : "", - ((scb.scb_command & SCB_CMD_RUC) == - SCB_CMD_RUC_SUS) ? "suspend reception" : "", - ((scb.scb_command & SCB_CMD_RUC) == - SCB_CMD_RUC_ABT) ? "abort reception" : ""); - - printk(KERN_DEBUG "cbl_offset 0x%x ", scb.scb_cbl_offset); - printk("rfa_offset 0x%x\n", scb.scb_rfa_offset); - - printk(KERN_DEBUG "crcerrs %d ", scb.scb_crcerrs); - printk("alnerrs %d ", scb.scb_alnerrs); - printk("rscerrs %d ", scb.scb_rscerrs); - printk("ovrnerrs %d\n", scb.scb_ovrnerrs); -} - -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the i82586's receive unit. - */ -static void wv_ru_show(struct net_device * dev) -{ - printk(KERN_DEBUG - "##### WaveLAN i82586 receiver unit status: #####\n"); - printk(KERN_DEBUG "ru:"); - /* - * Not implemented yet - */ - printk("\n"); -} /* wv_ru_show */ - -/*------------------------------------------------------------------*/ -/* - * Display info about one control block of the i82586 memory. - */ -static void wv_cu_show_one(struct net_device * dev, net_local * lp, int i, u16 p) -{ - unsigned long ioaddr; - ac_tx_t actx; - - ioaddr = dev->base_addr; - - printk("%d: 0x%x:", i, p); - - obram_read(ioaddr, p, (unsigned char *) &actx, sizeof(actx)); - printk(" status=0x%x,", actx.tx_h.ac_status); - printk(" command=0x%x,", actx.tx_h.ac_command); - - /* - { - tbd_t tbd; - - obram_read(ioaddr, actx.tx_tbd_offset, (unsigned char *)&tbd, sizeof(tbd)); - printk(" tbd_status=0x%x,", tbd.tbd_status); - } - */ - - printk("|"); -} - -/*------------------------------------------------------------------*/ -/* - * Print status of the command unit of the i82586. - */ -static void wv_cu_show(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned int i; - u16 p; - - printk(KERN_DEBUG - "##### WaveLAN i82586 command unit status: #####\n"); - - printk(KERN_DEBUG); - for (i = 0, p = lp->tx_first_in_use; i < NTXBLOCKS; i++) { - wv_cu_show_one(dev, lp, i, p); - - p += TXBLOCKZ; - if (p >= OFFSET_CU + NTXBLOCKS * TXBLOCKZ) - p -= NTXBLOCKS * TXBLOCKZ; - } - printk("\n"); -} -#endif /* DEBUG_I82586_SHOW */ - -#ifdef DEBUG_DEVICE_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the WaveLAN PCMCIA device driver. - */ -static void wv_dev_show(struct net_device * dev) -{ - printk(KERN_DEBUG "dev:"); - printk(" state=%lX,", dev->state); - printk(" trans_start=%ld,", dev->trans_start); - printk(" flags=0x%x,", dev->flags); - printk("\n"); -} /* wv_dev_show */ - -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the WaveLAN PCMCIA device driver's - * private information. - */ -static void wv_local_show(struct net_device * dev) -{ - net_local *lp; - - lp = netdev_priv(dev); - - printk(KERN_DEBUG "local:"); - printk(" tx_n_in_use=%d,", lp->tx_n_in_use); - printk(" hacr=0x%x,", lp->hacr); - printk(" rx_head=0x%x,", lp->rx_head); - printk(" rx_last=0x%x,", lp->rx_last); - printk(" tx_first_free=0x%x,", lp->tx_first_free); - printk(" tx_first_in_use=0x%x,", lp->tx_first_in_use); - printk("\n"); -} /* wv_local_show */ -#endif /* DEBUG_DEVICE_SHOW */ - -#if defined(DEBUG_RX_INFO) || defined(DEBUG_TX_INFO) -/*------------------------------------------------------------------*/ -/* - * Dump packet header (and content if necessary) on the screen - */ -static inline void wv_packet_info(u8 * p, /* Packet to dump */ - int length, /* Length of the packet */ - char *msg1, /* Name of the device */ - char *msg2) -{ /* Name of the function */ - int i; - int maxi; - - printk(KERN_DEBUG - "%s: %s(): dest %pM, length %d\n", - msg1, msg2, p, length); - printk(KERN_DEBUG - "%s: %s(): src %pM, type 0x%02X%02X\n", - msg1, msg2, &p[6], p[12], p[13]); - -#ifdef DEBUG_PACKET_DUMP - - printk(KERN_DEBUG "data=\""); - - if ((maxi = length) > DEBUG_PACKET_DUMP) - maxi = DEBUG_PACKET_DUMP; - for (i = 14; i < maxi; i++) - if (p[i] >= ' ' && p[i] <= '~') - printk(" %c", p[i]); - else - printk("%02X", p[i]); - if (maxi < length) - printk(".."); - printk("\"\n"); - printk(KERN_DEBUG "\n"); -#endif /* DEBUG_PACKET_DUMP */ -} -#endif /* defined(DEBUG_RX_INFO) || defined(DEBUG_TX_INFO) */ - -/*------------------------------------------------------------------*/ -/* - * This is the information which is displayed by the driver at startup. - * There are lots of flags for configuring it to your liking. - */ -static void wv_init_info(struct net_device * dev) -{ - short ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - - /* Read the parameter storage area */ - psa_read(ioaddr, lp->hacr, 0, (unsigned char *) &psa, sizeof(psa)); - -#ifdef DEBUG_PSA_SHOW - wv_psa_show(&psa); -#endif -#ifdef DEBUG_MMC_SHOW - wv_mmc_show(dev); -#endif -#ifdef DEBUG_I82586_SHOW - wv_cu_show(dev); -#endif - -#ifdef DEBUG_BASIC_SHOW - /* Now, let's go for the basic stuff. */ - printk(KERN_NOTICE "%s: WaveLAN at %#x, %pM, IRQ %d", - dev->name, ioaddr, dev->dev_addr, dev->irq); - - /* Print current network ID. */ - if (psa.psa_nwid_select) - printk(", nwid 0x%02X-%02X", psa.psa_nwid[0], - psa.psa_nwid[1]); - else - printk(", nwid off"); - - /* If 2.00 card */ - if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) { - unsigned short freq; - - /* Ask the EEPROM to read the frequency from the first area. */ - fee_read(ioaddr, 0x00, &freq, 1); - - /* Print frequency */ - printk(", 2.00, %ld", (freq >> 6) + 2400L); - - /* Hack! */ - if (freq & 0x20) - printk(".5"); - } else { - printk(", PC"); - switch (psa.psa_comp_number) { - case PSA_COMP_PC_AT_915: - case PSA_COMP_PC_AT_2400: - printk("-AT"); - break; - case PSA_COMP_PC_MC_915: - case PSA_COMP_PC_MC_2400: - printk("-MC"); - break; - case PSA_COMP_PCMCIA_915: - printk("MCIA"); - break; - default: - printk("?"); - } - printk(", "); - switch (psa.psa_subband) { - case PSA_SUBBAND_915: - printk("915"); - break; - case PSA_SUBBAND_2425: - printk("2425"); - break; - case PSA_SUBBAND_2460: - printk("2460"); - break; - case PSA_SUBBAND_2484: - printk("2484"); - break; - case PSA_SUBBAND_2430_5: - printk("2430.5"); - break; - default: - printk("?"); - } - } - - printk(" MHz\n"); -#endif /* DEBUG_BASIC_SHOW */ - -#ifdef DEBUG_VERSION_SHOW - /* Print version information */ - printk(KERN_NOTICE "%s", version); -#endif -} /* wv_init_info */ - -/********************* IOCTL, STATS & RECONFIG *********************/ -/* - * We found here routines that are called by Linux on different - * occasions after the configuration and not for transmitting data - * These may be called when the user use ifconfig, /proc/net/dev - * or wireless extensions - */ - - -/*------------------------------------------------------------------*/ -/* - * Set or clear the multicast filter for this adaptor. - * num_addrs == -1 Promiscuous mode, receive all packets - * num_addrs == 0 Normal mode, clear multicast list - * num_addrs > 0 Multicast mode, receive normal and MC packets, - * and do best-effort filtering. - */ -static void wavelan_set_multicast_list(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: ->wavelan_set_multicast_list()\n", - dev->name); -#endif - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG - "%s: wavelan_set_multicast_list(): setting Rx mode %02X to %d addresses.\n", - dev->name, dev->flags, dev->mc_count); -#endif - - /* Are we asking for promiscuous mode, - * or all multicast addresses (we don't have that!) - * or too many multicast addresses for the hardware filter? */ - if ((dev->flags & IFF_PROMISC) || - (dev->flags & IFF_ALLMULTI) || - (dev->mc_count > I82586_MAX_MULTICAST_ADDRESSES)) { - /* - * Enable promiscuous mode: receive all packets. - */ - if (!lp->promiscuous) { - lp->promiscuous = 1; - lp->mc_count = 0; - - wv_82586_reconfig(dev); - } - } else - /* Are there multicast addresses to send? */ - if (dev->mc_list != (struct dev_mc_list *) NULL) { - /* - * Disable promiscuous mode, but receive all packets - * in multicast list - */ -#ifdef MULTICAST_AVOID - if (lp->promiscuous || (dev->mc_count != lp->mc_count)) -#endif - { - lp->promiscuous = 0; - lp->mc_count = dev->mc_count; - - wv_82586_reconfig(dev); - } - } else { - /* - * Switch to normal mode: disable promiscuous mode and - * clear the multicast list. - */ - if (lp->promiscuous || lp->mc_count == 0) { - lp->promiscuous = 0; - lp->mc_count = 0; - - wv_82586_reconfig(dev); - } - } -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: <-wavelan_set_multicast_list()\n", - dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * This function doesn't exist. - * (Note : it was a nice way to test the reconfigure stuff...) - */ -#ifdef SET_MAC_ADDRESS -static int wavelan_set_mac_address(struct net_device * dev, void *addr) -{ - struct sockaddr *mac = addr; - - /* Copy the address. */ - memcpy(dev->dev_addr, mac->sa_data, WAVELAN_ADDR_SIZE); - - /* Reconfigure the beast. */ - wv_82586_reconfig(dev); - - return 0; -} -#endif /* SET_MAC_ADDRESS */ - - -/*------------------------------------------------------------------*/ -/* - * Frequency setting (for hardware capable of it) - * It's a bit complicated and you don't really want to look into it. - * (called in wavelan_ioctl) - */ -static int wv_set_frequency(unsigned long ioaddr, /* I/O port of the card */ - iw_freq * frequency) -{ - const int BAND_NUM = 10; /* Number of bands */ - long freq = 0L; /* offset to 2.4 GHz in .5 MHz */ -#ifdef DEBUG_IOCTL_INFO - int i; -#endif - - /* Setting by frequency */ - /* Theoretically, you may set any frequency between - * the two limits with a 0.5 MHz precision. In practice, - * I don't want you to have trouble with local regulations. - */ - if ((frequency->e == 1) && - (frequency->m >= (int) 2.412e8) - && (frequency->m <= (int) 2.487e8)) { - freq = ((frequency->m / 10000) - 24000L) / 5; - } - - /* Setting by channel (same as wfreqsel) */ - /* Warning: each channel is 22 MHz wide, so some of the channels - * will interfere. */ - if ((frequency->e == 0) && (frequency->m < BAND_NUM)) { - /* Get frequency offset. */ - freq = channel_bands[frequency->m] >> 1; - } - - /* Verify that the frequency is allowed. */ - if (freq != 0L) { - u16 table[10]; /* Authorized frequency table */ - - /* Read the frequency table. */ - fee_read(ioaddr, 0x71, table, 10); - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "Frequency table: "); - for (i = 0; i < 10; i++) { - printk(" %04X", table[i]); - } - printk("\n"); -#endif - - /* Look in the table to see whether the frequency is allowed. */ - if (!(table[9 - ((freq - 24) / 16)] & - (1 << ((freq - 24) % 16)))) return -EINVAL; /* not allowed */ - } else - return -EINVAL; - - /* if we get a usable frequency */ - if (freq != 0L) { - unsigned short area[16]; - unsigned short dac[2]; - unsigned short area_verify[16]; - unsigned short dac_verify[2]; - /* Corresponding gain (in the power adjust value table) - * See AT&T WaveLAN Data Manual, REF 407-024689/E, page 3-8 - * and WCIN062D.DOC, page 6.2.9. */ - unsigned short power_limit[] = { 40, 80, 120, 160, 0 }; - int power_band = 0; /* Selected band */ - unsigned short power_adjust; /* Correct value */ - - /* Search for the gain. */ - power_band = 0; - while ((freq > power_limit[power_band]) && - (power_limit[++power_band] != 0)); - - /* Read the first area. */ - fee_read(ioaddr, 0x00, area, 16); - - /* Read the DAC. */ - fee_read(ioaddr, 0x60, dac, 2); - - /* Read the new power adjust value. */ - fee_read(ioaddr, 0x6B - (power_band >> 1), &power_adjust, - 1); - if (power_band & 0x1) - power_adjust >>= 8; - else - power_adjust &= 0xFF; - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "WaveLAN EEPROM Area 1: "); - for (i = 0; i < 16; i++) { - printk(" %04X", area[i]); - } - printk("\n"); - - printk(KERN_DEBUG "WaveLAN EEPROM DAC: %04X %04X\n", - dac[0], dac[1]); -#endif - - /* Frequency offset (for info only) */ - area[0] = ((freq << 5) & 0xFFE0) | (area[0] & 0x1F); - - /* Receiver Principle main divider coefficient */ - area[3] = (freq >> 1) + 2400L - 352L; - area[2] = ((freq & 0x1) << 4) | (area[2] & 0xFFEF); - - /* Transmitter Main divider coefficient */ - area[13] = (freq >> 1) + 2400L; - area[12] = ((freq & 0x1) << 4) | (area[2] & 0xFFEF); - - /* Other parts of the area are flags, bit streams or unused. */ - - /* Set the value in the DAC. */ - dac[1] = ((power_adjust >> 1) & 0x7F) | (dac[1] & 0xFF80); - dac[0] = ((power_adjust & 0x1) << 4) | (dac[0] & 0xFFEF); - - /* Write the first area. */ - fee_write(ioaddr, 0x00, area, 16); - - /* Write the DAC. */ - fee_write(ioaddr, 0x60, dac, 2); - - /* We now should verify here that the writing of the EEPROM went OK. */ - - /* Reread the first area. */ - fee_read(ioaddr, 0x00, area_verify, 16); - - /* Reread the DAC. */ - fee_read(ioaddr, 0x60, dac_verify, 2); - - /* Compare. */ - if (memcmp(area, area_verify, 16 * 2) || - memcmp(dac, dac_verify, 2 * 2)) { -#ifdef DEBUG_IOCTL_ERROR - printk(KERN_INFO - "WaveLAN: wv_set_frequency: unable to write new frequency to EEPROM(?).\n"); -#endif - return -EOPNOTSUPP; - } - - /* We must download the frequency parameters to the - * synthesizers (from the EEPROM - area 1) - * Note: as the EEPROM is automatically decremented, we set the end - * if the area... */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), 0x0F); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), - MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD); - - /* Wait until the download is finished. */ - fee_wait(ioaddr, 100, 100); - - /* We must now download the power adjust value (gain) to - * the synthesizers (from the EEPROM - area 7 - DAC). */ - mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), 0x61); - mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), - MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD); - - /* Wait for the download to finish. */ - fee_wait(ioaddr, 100, 100); - -#ifdef DEBUG_IOCTL_INFO - /* Verification of what we have done */ - - printk(KERN_DEBUG "WaveLAN EEPROM Area 1: "); - for (i = 0; i < 16; i++) { - printk(" %04X", area_verify[i]); - } - printk("\n"); - - printk(KERN_DEBUG "WaveLAN EEPROM DAC: %04X %04X\n", - dac_verify[0], dac_verify[1]); -#endif - - return 0; - } else - return -EINVAL; /* Bah, never get there... */ -} - -/*------------------------------------------------------------------*/ -/* - * Give the list of available frequencies. - */ -static int wv_frequency_list(unsigned long ioaddr, /* I/O port of the card */ - iw_freq * list, /* List of frequencies to fill */ - int max) -{ /* Maximum number of frequencies */ - u16 table[10]; /* Authorized frequency table */ - long freq = 0L; /* offset to 2.4 GHz in .5 MHz + 12 MHz */ - int i; /* index in the table */ - int c = 0; /* Channel number */ - - /* Read the frequency table. */ - fee_read(ioaddr, 0x71 /* frequency table */ , table, 10); - - /* Check all frequencies. */ - i = 0; - for (freq = 0; freq < 150; freq++) - /* Look in the table if the frequency is allowed */ - if (table[9 - (freq / 16)] & (1 << (freq % 16))) { - /* Compute approximate channel number */ - while ((c < ARRAY_SIZE(channel_bands)) && - (((channel_bands[c] >> 1) - 24) < freq)) - c++; - list[i].i = c; /* Set the list index */ - - /* put in the list */ - list[i].m = (((freq + 24) * 5) + 24000L) * 10000; - list[i++].e = 1; - - /* Check number. */ - if (i >= max) - return (i); - } - - return (i); -} - -#ifdef IW_WIRELESS_SPY -/*------------------------------------------------------------------*/ -/* - * Gather wireless spy statistics: for each packet, compare the source - * address with our list, and if they match, get the statistics. - * Sorry, but this function really needs the wireless extensions. - */ -static inline void wl_spy_gather(struct net_device * dev, - u8 * mac, /* MAC address */ - u8 * stats) /* Statistics to gather */ -{ - struct iw_quality wstats; - - wstats.qual = stats[2] & MMR_SGNL_QUAL; - wstats.level = stats[0] & MMR_SIGNAL_LVL; - wstats.noise = stats[1] & MMR_SILENCE_LVL; - wstats.updated = 0x7; - - /* Update spy records */ - wireless_spy_update(dev, mac, &wstats); -} -#endif /* IW_WIRELESS_SPY */ - -#ifdef HISTOGRAM -/*------------------------------------------------------------------*/ -/* - * This function calculates a histogram of the signal level. - * As the noise is quite constant, it's like doing it on the SNR. - * We have defined a set of interval (lp->his_range), and each time - * the level goes in that interval, we increment the count (lp->his_sum). - * With this histogram you may detect if one WaveLAN is really weak, - * or you may also calculate the mean and standard deviation of the level. - */ -static inline void wl_his_gather(struct net_device * dev, u8 * stats) -{ /* Statistics to gather */ - net_local *lp = netdev_priv(dev); - u8 level = stats[0] & MMR_SIGNAL_LVL; - int i; - - /* Find the correct interval. */ - i = 0; - while ((i < (lp->his_number - 1)) - && (level >= lp->his_range[i++])); - - /* Increment interval counter. */ - (lp->his_sum[i])++; -} -#endif /* HISTOGRAM */ - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get protocol name - */ -static int wavelan_get_name(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - strcpy(wrqu->name, "WaveLAN"); - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set NWID - */ -static int wavelan_set_nwid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - mm_t m; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Set NWID in WaveLAN. */ - if (!wrqu->nwid.disabled) { - /* Set NWID in psa */ - psa.psa_nwid[0] = (wrqu->nwid.value & 0xFF00) >> 8; - psa.psa_nwid[1] = wrqu->nwid.value & 0xFF; - psa.psa_nwid_select = 0x01; - psa_write(ioaddr, lp->hacr, - (char *) psa.psa_nwid - (char *) &psa, - (unsigned char *) psa.psa_nwid, 3); - - /* Set NWID in mmc. */ - m.w.mmw_netw_id_l = psa.psa_nwid[1]; - m.w.mmw_netw_id_h = psa.psa_nwid[0]; - mmc_write(ioaddr, - (char *) &m.w.mmw_netw_id_l - - (char *) &m, - (unsigned char *) &m.w.mmw_netw_id_l, 2); - mmc_out(ioaddr, mmwoff(0, mmw_loopt_sel), 0x00); - } else { - /* Disable NWID in the psa. */ - psa.psa_nwid_select = 0x00; - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_nwid_select - - (char *) &psa, - (unsigned char *) &psa.psa_nwid_select, - 1); - - /* Disable NWID in the mmc (no filtering). */ - mmc_out(ioaddr, mmwoff(0, mmw_loopt_sel), - MMW_LOOPT_SEL_DIS_NWID); - } - /* update the Wavelan checksum */ - update_psa_checksum(dev, ioaddr, lp->hacr); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get NWID - */ -static int wavelan_get_nwid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Read the NWID. */ - psa_read(ioaddr, lp->hacr, - (char *) psa.psa_nwid - (char *) &psa, - (unsigned char *) psa.psa_nwid, 3); - wrqu->nwid.value = (psa.psa_nwid[0] << 8) + psa.psa_nwid[1]; - wrqu->nwid.disabled = !(psa.psa_nwid_select); - wrqu->nwid.fixed = 1; /* Superfluous */ - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set frequency - */ -static int wavelan_set_freq(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - unsigned long flags; - int ret; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). */ - if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) - ret = wv_set_frequency(ioaddr, &(wrqu->freq)); - else - ret = -EOPNOTSUPP; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get frequency - */ -static int wavelan_get_freq(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). - * Does it work for everybody, especially old cards? */ - if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) { - unsigned short freq; - - /* Ask the EEPROM to read the frequency from the first area. */ - fee_read(ioaddr, 0x00, &freq, 1); - wrqu->freq.m = ((freq >> 5) * 5 + 24000L) * 10000; - wrqu->freq.e = 1; - } else { - psa_read(ioaddr, lp->hacr, - (char *) &psa.psa_subband - (char *) &psa, - (unsigned char *) &psa.psa_subband, 1); - - if (psa.psa_subband <= 4) { - wrqu->freq.m = fixed_bands[psa.psa_subband]; - wrqu->freq.e = (psa.psa_subband != 0); - } else - ret = -EOPNOTSUPP; - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set level threshold - */ -static int wavelan_set_sens(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Set the level threshold. */ - /* We should complain loudly if wrqu->sens.fixed = 0, because we - * can't set auto mode... */ - psa.psa_thr_pre_set = wrqu->sens.value & 0x3F; - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_thr_pre_set - (char *) &psa, - (unsigned char *) &psa.psa_thr_pre_set, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev, ioaddr, lp->hacr); - mmc_out(ioaddr, mmwoff(0, mmw_thr_pre_set), - psa.psa_thr_pre_set); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get level threshold - */ -static int wavelan_get_sens(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Read the level threshold. */ - psa_read(ioaddr, lp->hacr, - (char *) &psa.psa_thr_pre_set - (char *) &psa, - (unsigned char *) &psa.psa_thr_pre_set, 1); - wrqu->sens.value = psa.psa_thr_pre_set & 0x3F; - wrqu->sens.fixed = 1; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set encryption key - */ -static int wavelan_set_encode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - unsigned long flags; - psa_t psa; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check if capable of encryption */ - if (!mmc_encr(ioaddr)) { - ret = -EOPNOTSUPP; - } - - /* Check the size of the key */ - if((wrqu->encoding.length != 8) && (wrqu->encoding.length != 0)) { - ret = -EINVAL; - } - - if(!ret) { - /* Basic checking... */ - if (wrqu->encoding.length == 8) { - /* Copy the key in the driver */ - memcpy(psa.psa_encryption_key, extra, - wrqu->encoding.length); - psa.psa_encryption_select = 1; - - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_encryption_select - - (char *) &psa, - (unsigned char *) &psa. - psa_encryption_select, 8 + 1); - - mmc_out(ioaddr, mmwoff(0, mmw_encr_enable), - MMW_ENCR_ENABLE_EN | MMW_ENCR_ENABLE_MODE); - mmc_write(ioaddr, mmwoff(0, mmw_encr_key), - (unsigned char *) &psa. - psa_encryption_key, 8); - } - - /* disable encryption */ - if (wrqu->encoding.flags & IW_ENCODE_DISABLED) { - psa.psa_encryption_select = 0; - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_encryption_select - - (char *) &psa, - (unsigned char *) &psa. - psa_encryption_select, 1); - - mmc_out(ioaddr, mmwoff(0, mmw_encr_enable), 0); - } - /* update the Wavelan checksum */ - update_psa_checksum(dev, ioaddr, lp->hacr); - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get encryption key - */ -static int wavelan_get_encode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check if encryption is available */ - if (!mmc_encr(ioaddr)) { - ret = -EOPNOTSUPP; - } else { - /* Read the encryption key */ - psa_read(ioaddr, lp->hacr, - (char *) &psa.psa_encryption_select - - (char *) &psa, - (unsigned char *) &psa. - psa_encryption_select, 1 + 8); - - /* encryption is enabled ? */ - if (psa.psa_encryption_select) - wrqu->encoding.flags = IW_ENCODE_ENABLED; - else - wrqu->encoding.flags = IW_ENCODE_DISABLED; - wrqu->encoding.flags |= mmc_encr(ioaddr); - - /* Copy the key to the user buffer */ - wrqu->encoding.length = 8; - memcpy(extra, psa.psa_encryption_key, wrqu->encoding.length); - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get range info - */ -static int wavelan_get_range(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - struct iw_range *range = (struct iw_range *) extra; - unsigned long flags; - int ret = 0; - - /* Set the length (very important for backward compatibility) */ - wrqu->data.length = sizeof(struct iw_range); - - /* Set all the info we don't care or don't know about to zero */ - memset(range, 0, sizeof(struct iw_range)); - - /* Set the Wireless Extension versions */ - range->we_version_compiled = WIRELESS_EXT; - range->we_version_source = 9; - - /* Set information in the range struct. */ - range->throughput = 1.6 * 1000 * 1000; /* don't argue on this ! */ - range->min_nwid = 0x0000; - range->max_nwid = 0xFFFF; - - range->sensitivity = 0x3F; - range->max_qual.qual = MMR_SGNL_QUAL; - range->max_qual.level = MMR_SIGNAL_LVL; - range->max_qual.noise = MMR_SILENCE_LVL; - range->avg_qual.qual = MMR_SGNL_QUAL; /* Always max */ - /* Need to get better values for those two */ - range->avg_qual.level = 30; - range->avg_qual.noise = 8; - - range->num_bitrates = 1; - range->bitrate[0] = 2000000; /* 2 Mb/s */ - - /* Event capability (kernel + driver) */ - range->event_capa[0] = (IW_EVENT_CAPA_MASK(0x8B02) | - IW_EVENT_CAPA_MASK(0x8B04)); - range->event_capa[1] = IW_EVENT_CAPA_K_1; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). */ - if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) { - range->num_channels = 10; - range->num_frequency = wv_frequency_list(ioaddr, range->freq, - IW_MAX_FREQUENCIES); - } else - range->num_channels = range->num_frequency = 0; - - /* Encryption supported ? */ - if (mmc_encr(ioaddr)) { - range->encoding_size[0] = 8; /* DES = 64 bits key */ - range->num_encoding_sizes = 1; - range->max_encoding_tokens = 1; /* Only one key possible */ - } else { - range->num_encoding_sizes = 0; - range->max_encoding_tokens = 0; - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : set quality threshold - */ -static int wavelan_set_qthr(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - psa.psa_quality_thr = *(extra) & 0x0F; - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_quality_thr - (char *) &psa, - (unsigned char *) &psa.psa_quality_thr, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev, ioaddr, lp->hacr); - mmc_out(ioaddr, mmwoff(0, mmw_quality_thr), - psa.psa_quality_thr); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : get quality threshold - */ -static int wavelan_get_qthr(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); /* lp is not unused */ - psa_t psa; - unsigned long flags; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - psa_read(ioaddr, lp->hacr, - (char *) &psa.psa_quality_thr - (char *) &psa, - (unsigned char *) &psa.psa_quality_thr, 1); - *(extra) = psa.psa_quality_thr & 0x0F; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return 0; -} - -#ifdef HISTOGRAM -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : set histogram - */ -static int wavelan_set_histo(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); /* lp is not unused */ - - /* Check the number of intervals. */ - if (wrqu->data.length > 16) { - return(-E2BIG); - } - - /* Disable histo while we copy the addresses. - * As we don't disable interrupts, we need to do this */ - lp->his_number = 0; - - /* Are there ranges to copy? */ - if (wrqu->data.length > 0) { - /* Copy interval ranges to the driver */ - memcpy(lp->his_range, extra, wrqu->data.length); - - { - int i; - printk(KERN_DEBUG "Histo :"); - for(i = 0; i < wrqu->data.length; i++) - printk(" %d", lp->his_range[i]); - printk("\n"); - } - - /* Reset result structure. */ - memset(lp->his_sum, 0x00, sizeof(long) * 16); - } - - /* Now we can set the number of ranges */ - lp->his_number = wrqu->data.length; - - return(0); -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : get histogram - */ -static int wavelan_get_histo(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); /* lp is not unused */ - - /* Set the number of intervals. */ - wrqu->data.length = lp->his_number; - - /* Give back the distribution statistics */ - if(lp->his_number > 0) - memcpy(extra, lp->his_sum, sizeof(long) * lp->his_number); - - return(0); -} -#endif /* HISTOGRAM */ - -/*------------------------------------------------------------------*/ -/* - * Structures to export the Wireless Handlers - */ - -static const iw_handler wavelan_handler[] = -{ - NULL, /* SIOCSIWNAME */ - wavelan_get_name, /* SIOCGIWNAME */ - wavelan_set_nwid, /* SIOCSIWNWID */ - wavelan_get_nwid, /* SIOCGIWNWID */ - wavelan_set_freq, /* SIOCSIWFREQ */ - wavelan_get_freq, /* SIOCGIWFREQ */ - NULL, /* SIOCSIWMODE */ - NULL, /* SIOCGIWMODE */ - wavelan_set_sens, /* SIOCSIWSENS */ - wavelan_get_sens, /* SIOCGIWSENS */ - NULL, /* SIOCSIWRANGE */ - wavelan_get_range, /* SIOCGIWRANGE */ - NULL, /* SIOCSIWPRIV */ - NULL, /* SIOCGIWPRIV */ - NULL, /* SIOCSIWSTATS */ - NULL, /* SIOCGIWSTATS */ - iw_handler_set_spy, /* SIOCSIWSPY */ - iw_handler_get_spy, /* SIOCGIWSPY */ - iw_handler_set_thrspy, /* SIOCSIWTHRSPY */ - iw_handler_get_thrspy, /* SIOCGIWTHRSPY */ - NULL, /* SIOCSIWAP */ - NULL, /* SIOCGIWAP */ - NULL, /* -- hole -- */ - NULL, /* SIOCGIWAPLIST */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWESSID */ - NULL, /* SIOCGIWESSID */ - NULL, /* SIOCSIWNICKN */ - NULL, /* SIOCGIWNICKN */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWRATE */ - NULL, /* SIOCGIWRATE */ - NULL, /* SIOCSIWRTS */ - NULL, /* SIOCGIWRTS */ - NULL, /* SIOCSIWFRAG */ - NULL, /* SIOCGIWFRAG */ - NULL, /* SIOCSIWTXPOW */ - NULL, /* SIOCGIWTXPOW */ - NULL, /* SIOCSIWRETRY */ - NULL, /* SIOCGIWRETRY */ - /* Bummer ! Why those are only at the end ??? */ - wavelan_set_encode, /* SIOCSIWENCODE */ - wavelan_get_encode, /* SIOCGIWENCODE */ -}; - -static const iw_handler wavelan_private_handler[] = -{ - wavelan_set_qthr, /* SIOCIWFIRSTPRIV */ - wavelan_get_qthr, /* SIOCIWFIRSTPRIV + 1 */ -#ifdef HISTOGRAM - wavelan_set_histo, /* SIOCIWFIRSTPRIV + 2 */ - wavelan_get_histo, /* SIOCIWFIRSTPRIV + 3 */ -#endif /* HISTOGRAM */ -}; - -static const struct iw_priv_args wavelan_private_args[] = { -/*{ cmd, set_args, get_args, name } */ - { SIOCSIPQTHR, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, 0, "setqualthr" }, - { SIOCGIPQTHR, 0, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, "getqualthr" }, - { SIOCSIPHISTO, IW_PRIV_TYPE_BYTE | 16, 0, "sethisto" }, - { SIOCGIPHISTO, 0, IW_PRIV_TYPE_INT | 16, "gethisto" }, -}; - -static const struct iw_handler_def wavelan_handler_def = -{ - .num_standard = ARRAY_SIZE(wavelan_handler), - .num_private = ARRAY_SIZE(wavelan_private_handler), - .num_private_args = ARRAY_SIZE(wavelan_private_args), - .standard = wavelan_handler, - .private = wavelan_private_handler, - .private_args = wavelan_private_args, - .get_wireless_stats = wavelan_get_wireless_stats, -}; - -/*------------------------------------------------------------------*/ -/* - * Get wireless statistics. - * Called by /proc/net/wireless - */ -static iw_stats *wavelan_get_wireless_stats(struct net_device * dev) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); - mmr_t m; - iw_stats *wstats; - unsigned long flags; - -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: ->wavelan_get_wireless_stats()\n", - dev->name); -#endif - - /* Check */ - if (lp == (net_local *) NULL) - return (iw_stats *) NULL; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - wstats = &lp->wstats; - - /* Get data from the mmc. */ - mmc_out(ioaddr, mmwoff(0, mmw_freeze), 1); - - mmc_read(ioaddr, mmroff(0, mmr_dce_status), &m.mmr_dce_status, 1); - mmc_read(ioaddr, mmroff(0, mmr_wrong_nwid_l), &m.mmr_wrong_nwid_l, - 2); - mmc_read(ioaddr, mmroff(0, mmr_thr_pre_set), &m.mmr_thr_pre_set, - 4); - - mmc_out(ioaddr, mmwoff(0, mmw_freeze), 0); - - /* Copy data to wireless stuff. */ - wstats->status = m.mmr_dce_status & MMR_DCE_STATUS; - wstats->qual.qual = m.mmr_sgnl_qual & MMR_SGNL_QUAL; - wstats->qual.level = m.mmr_signal_lvl & MMR_SIGNAL_LVL; - wstats->qual.noise = m.mmr_silence_lvl & MMR_SILENCE_LVL; - wstats->qual.updated = (((m. mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) >> 7) - | ((m.mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) >> 6) - | ((m.mmr_silence_lvl & MMR_SILENCE_LVL_VALID) >> 5)); - wstats->discard.nwid += (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l; - wstats->discard.code = 0L; - wstats->discard.misc = 0L; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: <-wavelan_get_wireless_stats()\n", - dev->name); -#endif - return &lp->wstats; -} - -/************************* PACKET RECEPTION *************************/ -/* - * This part deals with receiving the packets. - * The interrupt handler gets an interrupt when a packet has been - * successfully received and calls this part. - */ - -/*------------------------------------------------------------------*/ -/* - * This routine does the actual copying of data (including the Ethernet - * header structure) from the WaveLAN card to an sk_buff chain that - * will be passed up to the network interface layer. NOTE: we - * currently don't handle trailer protocols (neither does the rest of - * the network interface), so if that is needed, it will (at least in - * part) be added here. The contents of the receive ring buffer are - * copied to a message chain that is then passed to the kernel. - * - * Note: if any errors occur, the packet is "dropped on the floor". - * (called by wv_packet_rcv()) - */ -static void -wv_packet_read(struct net_device * dev, u16 buf_off, int sksize) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - struct sk_buff *skb; - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: ->wv_packet_read(0x%X, %d)\n", - dev->name, buf_off, sksize); -#endif - - /* Allocate buffer for the data */ - if ((skb = dev_alloc_skb(sksize)) == (struct sk_buff *) NULL) { -#ifdef DEBUG_RX_ERROR - printk(KERN_INFO - "%s: wv_packet_read(): could not alloc_skb(%d, GFP_ATOMIC).\n", - dev->name, sksize); -#endif - dev->stats.rx_dropped++; - return; - } - - /* Copy the packet to the buffer. */ - obram_read(ioaddr, buf_off, skb_put(skb, sksize), sksize); - skb->protocol = eth_type_trans(skb, dev); - -#ifdef DEBUG_RX_INFO - wv_packet_info(skb_mac_header(skb), sksize, dev->name, - "wv_packet_read"); -#endif /* DEBUG_RX_INFO */ - - /* Statistics-gathering and associated stuff. - * It seem a bit messy with all the define, but it's really - * simple... */ - if ( -#ifdef IW_WIRELESS_SPY /* defined in iw_handler.h */ - (lp->spy_data.spy_number > 0) || -#endif /* IW_WIRELESS_SPY */ -#ifdef HISTOGRAM - (lp->his_number > 0) || -#endif /* HISTOGRAM */ - 0) { - u8 stats[3]; /* signal level, noise level, signal quality */ - - /* Read signal level, silence level and signal quality bytes */ - /* Note: in the PCMCIA hardware, these are part of the frame. - * It seems that for the ISA hardware, it's nowhere to be - * found in the frame, so I'm obliged to do this (it has a - * side effect on /proc/net/wireless). - * Any ideas? - */ - mmc_out(ioaddr, mmwoff(0, mmw_freeze), 1); - mmc_read(ioaddr, mmroff(0, mmr_signal_lvl), stats, 3); - mmc_out(ioaddr, mmwoff(0, mmw_freeze), 0); - -#ifdef DEBUG_RX_INFO - printk(KERN_DEBUG - "%s: wv_packet_read(): Signal level %d/63, Silence level %d/63, signal quality %d/16\n", - dev->name, stats[0] & 0x3F, stats[1] & 0x3F, - stats[2] & 0x0F); -#endif - - /* Spying stuff */ -#ifdef IW_WIRELESS_SPY - wl_spy_gather(dev, skb_mac_header(skb) + WAVELAN_ADDR_SIZE, - stats); -#endif /* IW_WIRELESS_SPY */ -#ifdef HISTOGRAM - wl_his_gather(dev, stats); -#endif /* HISTOGRAM */ - } - - /* - * Hand the packet to the network module. - */ - netif_rx(skb); - - /* Keep statistics up to date */ - dev->stats.rx_packets++; - dev->stats.rx_bytes += sksize; - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: <-wv_packet_read()\n", dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * Transfer as many packets as we can - * from the device RAM. - * (called in wavelan_interrupt()). - * Note : the spinlock is already grabbed for us. - */ -static void wv_receive(struct net_device * dev) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); - fd_t fd; - rbd_t rbd; - int nreaped = 0; - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: ->wv_receive()\n", dev->name); -#endif - - /* Loop on each received packet. */ - for (;;) { - obram_read(ioaddr, lp->rx_head, (unsigned char *) &fd, - sizeof(fd)); - - /* Note about the status : - * It start up to be 0 (the value we set). Then, when the RU - * grab the buffer to prepare for reception, it sets the - * FD_STATUS_B flag. When the RU has finished receiving the - * frame, it clears FD_STATUS_B, set FD_STATUS_C to indicate - * completion and set the other flags to indicate the eventual - * errors. FD_STATUS_OK indicates that the reception was OK. - */ - - /* If the current frame is not complete, we have reached the end. */ - if ((fd.fd_status & FD_STATUS_C) != FD_STATUS_C) - break; /* This is how we exit the loop. */ - - nreaped++; - - /* Check whether frame was correctly received. */ - if ((fd.fd_status & FD_STATUS_OK) == FD_STATUS_OK) { - /* Does the frame contain a pointer to the data? Let's check. */ - if (fd.fd_rbd_offset != I82586NULL) { - /* Read the receive buffer descriptor */ - obram_read(ioaddr, fd.fd_rbd_offset, - (unsigned char *) &rbd, - sizeof(rbd)); - -#ifdef DEBUG_RX_ERROR - if ((rbd.rbd_status & RBD_STATUS_EOF) != - RBD_STATUS_EOF) printk(KERN_INFO - "%s: wv_receive(): missing EOF flag.\n", - dev->name); - - if ((rbd.rbd_status & RBD_STATUS_F) != - RBD_STATUS_F) printk(KERN_INFO - "%s: wv_receive(): missing F flag.\n", - dev->name); -#endif /* DEBUG_RX_ERROR */ - - /* Read the packet and transmit to Linux */ - wv_packet_read(dev, rbd.rbd_bufl, - rbd. - rbd_status & - RBD_STATUS_ACNT); - } -#ifdef DEBUG_RX_ERROR - else /* if frame has no data */ - printk(KERN_INFO - "%s: wv_receive(): frame has no data.\n", - dev->name); -#endif - } else { /* If reception was no successful */ - - dev->stats.rx_errors++; - -#ifdef DEBUG_RX_INFO - printk(KERN_DEBUG - "%s: wv_receive(): frame not received successfully (%X).\n", - dev->name, fd.fd_status); -#endif - -#ifdef DEBUG_RX_ERROR - if ((fd.fd_status & FD_STATUS_S6) != 0) - printk(KERN_INFO - "%s: wv_receive(): no EOF flag.\n", - dev->name); -#endif - - if ((fd.fd_status & FD_STATUS_S7) != 0) { - dev->stats.rx_length_errors++; -#ifdef DEBUG_RX_FAIL - printk(KERN_DEBUG - "%s: wv_receive(): frame too short.\n", - dev->name); -#endif - } - - if ((fd.fd_status & FD_STATUS_S8) != 0) { - dev->stats.rx_over_errors++; -#ifdef DEBUG_RX_FAIL - printk(KERN_DEBUG - "%s: wv_receive(): rx DMA overrun.\n", - dev->name); -#endif - } - - if ((fd.fd_status & FD_STATUS_S9) != 0) { - dev->stats.rx_fifo_errors++; -#ifdef DEBUG_RX_FAIL - printk(KERN_DEBUG - "%s: wv_receive(): ran out of resources.\n", - dev->name); -#endif - } - - if ((fd.fd_status & FD_STATUS_S10) != 0) { - dev->stats.rx_frame_errors++; -#ifdef DEBUG_RX_FAIL - printk(KERN_DEBUG - "%s: wv_receive(): alignment error.\n", - dev->name); -#endif - } - - if ((fd.fd_status & FD_STATUS_S11) != 0) { - dev->stats.rx_crc_errors++; -#ifdef DEBUG_RX_FAIL - printk(KERN_DEBUG - "%s: wv_receive(): CRC error.\n", - dev->name); -#endif - } - } - - fd.fd_status = 0; - obram_write(ioaddr, fdoff(lp->rx_head, fd_status), - (unsigned char *) &fd.fd_status, - sizeof(fd.fd_status)); - - fd.fd_command = FD_COMMAND_EL; - obram_write(ioaddr, fdoff(lp->rx_head, fd_command), - (unsigned char *) &fd.fd_command, - sizeof(fd.fd_command)); - - fd.fd_command = 0; - obram_write(ioaddr, fdoff(lp->rx_last, fd_command), - (unsigned char *) &fd.fd_command, - sizeof(fd.fd_command)); - - lp->rx_last = lp->rx_head; - lp->rx_head = fd.fd_link_offset; - } /* for(;;) -> loop on all frames */ - -#ifdef DEBUG_RX_INFO - if (nreaped > 1) - printk(KERN_DEBUG "%s: wv_receive(): reaped %d\n", - dev->name, nreaped); -#endif -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: <-wv_receive()\n", dev->name); -#endif -} - -/*********************** PACKET TRANSMISSION ***********************/ -/* - * This part deals with sending packets through the WaveLAN. - * - */ - -/*------------------------------------------------------------------*/ -/* - * This routine fills in the appropriate registers and memory - * locations on the WaveLAN card and starts the card off on - * the transmit. - * - * The principle: - * Each block contains a transmit command, a NOP command, - * a transmit block descriptor and a buffer. - * The CU read the transmit block which point to the tbd, - * read the tbd and the content of the buffer. - * When it has finish with it, it goes to the next command - * which in our case is the NOP. The NOP points on itself, - * so the CU stop here. - * When we add the next block, we modify the previous nop - * to make it point on the new tx command. - * Simple, isn't it ? - * - * (called in wavelan_packet_xmit()) - */ -static int wv_packet_write(struct net_device * dev, void *buf, short length) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - unsigned short txblock; - unsigned short txpred; - unsigned short tx_addr; - unsigned short nop_addr; - unsigned short tbd_addr; - unsigned short buf_addr; - ac_tx_t tx; - ac_nop_t nop; - tbd_t tbd; - int clen = length; - unsigned long flags; - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: ->wv_packet_write(%d)\n", dev->name, - length); -#endif - - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check nothing bad has happened */ - if (lp->tx_n_in_use == (NTXBLOCKS - 1)) { -#ifdef DEBUG_TX_ERROR - printk(KERN_INFO "%s: wv_packet_write(): Tx queue full.\n", - dev->name); -#endif - spin_unlock_irqrestore(&lp->spinlock, flags); - return 1; - } - - /* Calculate addresses of next block and previous block. */ - txblock = lp->tx_first_free; - txpred = txblock - TXBLOCKZ; - if (txpred < OFFSET_CU) - txpred += NTXBLOCKS * TXBLOCKZ; - lp->tx_first_free += TXBLOCKZ; - if (lp->tx_first_free >= OFFSET_CU + NTXBLOCKS * TXBLOCKZ) - lp->tx_first_free -= NTXBLOCKS * TXBLOCKZ; - - lp->tx_n_in_use++; - - /* Calculate addresses of the different parts of the block. */ - tx_addr = txblock; - nop_addr = tx_addr + sizeof(tx); - tbd_addr = nop_addr + sizeof(nop); - buf_addr = tbd_addr + sizeof(tbd); - - /* - * Transmit command - */ - tx.tx_h.ac_status = 0; - obram_write(ioaddr, toff(ac_tx_t, tx_addr, tx_h.ac_status), - (unsigned char *) &tx.tx_h.ac_status, - sizeof(tx.tx_h.ac_status)); - - /* - * NOP command - */ - nop.nop_h.ac_status = 0; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status), - (unsigned char *) &nop.nop_h.ac_status, - sizeof(nop.nop_h.ac_status)); - nop.nop_h.ac_link = nop_addr; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link), - (unsigned char *) &nop.nop_h.ac_link, - sizeof(nop.nop_h.ac_link)); - - /* - * Transmit buffer descriptor - */ - tbd.tbd_status = TBD_STATUS_EOF | (TBD_STATUS_ACNT & clen); - tbd.tbd_next_bd_offset = I82586NULL; - tbd.tbd_bufl = buf_addr; - tbd.tbd_bufh = 0; - obram_write(ioaddr, tbd_addr, (unsigned char *) &tbd, sizeof(tbd)); - - /* - * Data - */ - obram_write(ioaddr, buf_addr, buf, length); - - /* - * Overwrite the predecessor NOP link - * so that it points to this txblock. - */ - nop_addr = txpred + sizeof(tx); - nop.nop_h.ac_status = 0; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status), - (unsigned char *) &nop.nop_h.ac_status, - sizeof(nop.nop_h.ac_status)); - nop.nop_h.ac_link = txblock; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link), - (unsigned char *) &nop.nop_h.ac_link, - sizeof(nop.nop_h.ac_link)); - - /* Make sure the watchdog will keep quiet for a while */ - dev->trans_start = jiffies; - - /* Keep stats up to date. */ - dev->stats.tx_bytes += length; - - if (lp->tx_first_in_use == I82586NULL) - lp->tx_first_in_use = txblock; - - if (lp->tx_n_in_use < NTXBLOCKS - 1) - netif_wake_queue(dev); - - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_TX_INFO - wv_packet_info((u8 *) buf, length, dev->name, - "wv_packet_write"); -#endif /* DEBUG_TX_INFO */ - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: <-wv_packet_write()\n", dev->name); -#endif - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * This routine is called when we want to send a packet (NET3 callback) - * In this routine, we check if the harware is ready to accept - * the packet. We also prevent reentrance. Then we call the function - * to send the packet. - */ -static netdev_tx_t wavelan_packet_xmit(struct sk_buff *skb, - struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - char data[ETH_ZLEN]; - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: ->wavelan_packet_xmit(0x%X)\n", dev->name, - (unsigned) skb); -#endif - - /* - * Block a timer-based transmit from overlapping. - * In other words, prevent reentering this routine. - */ - netif_stop_queue(dev); - - /* If somebody has asked to reconfigure the controller, - * we can do it now. - */ - if (lp->reconfig_82586) { - spin_lock_irqsave(&lp->spinlock, flags); - wv_82586_config(dev); - spin_unlock_irqrestore(&lp->spinlock, flags); - /* Check that we can continue */ - if (lp->tx_n_in_use == (NTXBLOCKS - 1)) - return NETDEV_TX_BUSY; - } - - /* Do we need some padding? */ - /* Note : on wireless the propagation time is in the order of 1us, - * and we don't have the Ethernet specific requirement of beeing - * able to detect collisions, therefore in theory we don't really - * need to pad. Jean II */ - if (skb->len < ETH_ZLEN) { - memset(data, 0, ETH_ZLEN); - skb_copy_from_linear_data(skb, data, skb->len); - /* Write packet on the card */ - if(wv_packet_write(dev, data, ETH_ZLEN)) - return NETDEV_TX_BUSY; /* We failed */ - } - else if(wv_packet_write(dev, skb->data, skb->len)) - return NETDEV_TX_BUSY; /* We failed */ - - - dev_kfree_skb(skb); - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: <-wavelan_packet_xmit()\n", dev->name); -#endif - return NETDEV_TX_OK; -} - -/*********************** HARDWARE CONFIGURATION ***********************/ -/* - * This part does the real job of starting and configuring the hardware. - */ - -/*--------------------------------------------------------------------*/ -/* - * Routine to initialize the Modem Management Controller. - * (called by wv_hw_reset()) - */ -static int wv_mmc_init(struct net_device * dev) -{ - unsigned long ioaddr = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - mmw_t m; - int configured; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_mmc_init()\n", dev->name); -#endif - - /* Read the parameter storage area. */ - psa_read(ioaddr, lp->hacr, 0, (unsigned char *) &psa, sizeof(psa)); - -#ifdef USE_PSA_CONFIG - configured = psa.psa_conf_status & 1; -#else - configured = 0; -#endif - - /* Is the PSA is not configured */ - if (!configured) { - /* User will be able to configure NWID later (with iwconfig). */ - psa.psa_nwid[0] = 0; - psa.psa_nwid[1] = 0; - - /* no NWID checking since NWID is not set */ - psa.psa_nwid_select = 0; - - /* Disable encryption */ - psa.psa_encryption_select = 0; - - /* Set to standard values: - * 0x04 for AT, - * 0x01 for MCA, - * 0x04 for PCMCIA and 2.00 card (AT&T 407-024689/E document) - */ - if (psa.psa_comp_number & 1) - psa.psa_thr_pre_set = 0x01; - else - psa.psa_thr_pre_set = 0x04; - psa.psa_quality_thr = 0x03; - - /* It is configured */ - psa.psa_conf_status |= 1; - -#ifdef USE_PSA_CONFIG - /* Write the psa. */ - psa_write(ioaddr, lp->hacr, - (char *) psa.psa_nwid - (char *) &psa, - (unsigned char *) psa.psa_nwid, 4); - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_thr_pre_set - (char *) &psa, - (unsigned char *) &psa.psa_thr_pre_set, 1); - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_quality_thr - (char *) &psa, - (unsigned char *) &psa.psa_quality_thr, 1); - psa_write(ioaddr, lp->hacr, - (char *) &psa.psa_conf_status - (char *) &psa, - (unsigned char *) &psa.psa_conf_status, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev, ioaddr, lp->hacr); -#endif - } - - /* Zero the mmc structure. */ - memset(&m, 0x00, sizeof(m)); - - /* Copy PSA info to the mmc. */ - m.mmw_netw_id_l = psa.psa_nwid[1]; - m.mmw_netw_id_h = psa.psa_nwid[0]; - - if (psa.psa_nwid_select & 1) - m.mmw_loopt_sel = 0x00; - else - m.mmw_loopt_sel = MMW_LOOPT_SEL_DIS_NWID; - - memcpy(&m.mmw_encr_key, &psa.psa_encryption_key, - sizeof(m.mmw_encr_key)); - - if (psa.psa_encryption_select) - m.mmw_encr_enable = - MMW_ENCR_ENABLE_EN | MMW_ENCR_ENABLE_MODE; - else - m.mmw_encr_enable = 0; - - m.mmw_thr_pre_set = psa.psa_thr_pre_set & 0x3F; - m.mmw_quality_thr = psa.psa_quality_thr & 0x0F; - - /* - * Set default modem control parameters. - * See NCR document 407-0024326 Rev. A. - */ - m.mmw_jabber_enable = 0x01; - m.mmw_freeze = 0; - m.mmw_anten_sel = MMW_ANTEN_SEL_ALG_EN; - m.mmw_ifs = 0x20; - m.mmw_mod_delay = 0x04; - m.mmw_jam_time = 0x38; - - m.mmw_des_io_invert = 0; - m.mmw_decay_prm = 0; - m.mmw_decay_updat_prm = 0; - - /* Write all info to MMC. */ - mmc_write(ioaddr, 0, (u8 *) & m, sizeof(m)); - - /* The following code starts the modem of the 2.00 frequency - * selectable cards at power on. It's not strictly needed for the - * following boots. - * The original patch was by Joe Finney for the PCMCIA driver, but - * I've cleaned it up a bit and added documentation. - * Thanks to Loeke Brederveld from Lucent for the info. - */ - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable) - * Does it work for everybody, especially old cards? */ - /* Note: WFREQSEL verifies that it is able to read a sensible - * frequency from EEPROM (address 0x00) and that MMR_FEE_STATUS_ID - * is 0xA (Xilinx version) or 0xB (Ariadne version). - * My test is more crude but does work. */ - if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) { - /* We must download the frequency parameters to the - * synthesizers (from the EEPROM - area 1) - * Note: as the EEPROM is automatically decremented, we set the end - * if the area... */ - m.mmw_fee_addr = 0x0F; - m.mmw_fee_ctrl = MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD; - mmc_write(ioaddr, (char *) &m.mmw_fee_ctrl - (char *) &m, - (unsigned char *) &m.mmw_fee_ctrl, 2); - - /* Wait until the download is finished. */ - fee_wait(ioaddr, 100, 100); - -#ifdef DEBUG_CONFIG_INFO - /* The frequency was in the last word downloaded. */ - mmc_read(ioaddr, (char *) &m.mmw_fee_data_l - (char *) &m, - (unsigned char *) &m.mmw_fee_data_l, 2); - - /* Print some info for the user. */ - printk(KERN_DEBUG - "%s: WaveLAN 2.00 recognised (frequency select). Current frequency = %ld\n", - dev->name, - ((m. - mmw_fee_data_h << 4) | (m.mmw_fee_data_l >> 4)) * - 5 / 2 + 24000L); -#endif - - /* We must now download the power adjust value (gain) to - * the synthesizers (from the EEPROM - area 7 - DAC). */ - m.mmw_fee_addr = 0x61; - m.mmw_fee_ctrl = MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD; - mmc_write(ioaddr, (char *) &m.mmw_fee_ctrl - (char *) &m, - (unsigned char *) &m.mmw_fee_ctrl, 2); - - /* Wait until the download is finished. */ - } - /* if 2.00 card */ -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_mmc_init()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Construct the fd and rbd structures. - * Start the receive unit. - * (called by wv_hw_reset()) - */ -static int wv_ru_start(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - u16 scb_cs; - fd_t fd; - rbd_t rbd; - u16 rx; - u16 rx_next; - int i; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_ru_start()\n", dev->name); -#endif - - obram_read(ioaddr, scboff(OFFSET_SCB, scb_status), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - if ((scb_cs & SCB_ST_RUS) == SCB_ST_RUS_RDY) - return 0; - - lp->rx_head = OFFSET_RU; - - for (i = 0, rx = lp->rx_head; i < NRXBLOCKS; i++, rx = rx_next) { - rx_next = - (i == NRXBLOCKS - 1) ? lp->rx_head : rx + RXBLOCKZ; - - fd.fd_status = 0; - fd.fd_command = (i == NRXBLOCKS - 1) ? FD_COMMAND_EL : 0; - fd.fd_link_offset = rx_next; - fd.fd_rbd_offset = rx + sizeof(fd); - obram_write(ioaddr, rx, (unsigned char *) &fd, sizeof(fd)); - - rbd.rbd_status = 0; - rbd.rbd_next_rbd_offset = I82586NULL; - rbd.rbd_bufl = rx + sizeof(fd) + sizeof(rbd); - rbd.rbd_bufh = 0; - rbd.rbd_el_size = RBD_EL | (RBD_SIZE & MAXDATAZ); - obram_write(ioaddr, rx + sizeof(fd), - (unsigned char *) &rbd, sizeof(rbd)); - - lp->rx_last = rx; - } - - obram_write(ioaddr, scboff(OFFSET_SCB, scb_rfa_offset), - (unsigned char *) &lp->rx_head, sizeof(lp->rx_head)); - - scb_cs = SCB_CMD_RUC_GO; - obram_write(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - - set_chan_attn(ioaddr, lp->hacr); - - for (i = 1000; i > 0; i--) { - obram_read(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - if (scb_cs == 0) - break; - - udelay(10); - } - - if (i <= 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wavelan_ru_start(): board not accepting command.\n", - dev->name); -#endif - return -1; - } -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_ru_start()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Initialise the transmit blocks. - * Start the command unit executing the NOP - * self-loop of the first transmit block. - * - * Here we create the list of send buffers used to transmit packets - * between the PC and the command unit. For each buffer, we create a - * buffer descriptor (pointing on the buffer), a transmit command - * (pointing to the buffer descriptor) and a NOP command. - * The transmit command is linked to the NOP, and the NOP to itself. - * When we will have finished executing the transmit command, we will - * then loop on the NOP. By releasing the NOP link to a new command, - * we may send another buffer. - * - * (called by wv_hw_reset()) - */ -static int wv_cu_start(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - int i; - u16 txblock; - u16 first_nop; - u16 scb_cs; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_cu_start()\n", dev->name); -#endif - - lp->tx_first_free = OFFSET_CU; - lp->tx_first_in_use = I82586NULL; - - for (i = 0, txblock = OFFSET_CU; - i < NTXBLOCKS; i++, txblock += TXBLOCKZ) { - ac_tx_t tx; - ac_nop_t nop; - tbd_t tbd; - unsigned short tx_addr; - unsigned short nop_addr; - unsigned short tbd_addr; - unsigned short buf_addr; - - tx_addr = txblock; - nop_addr = tx_addr + sizeof(tx); - tbd_addr = nop_addr + sizeof(nop); - buf_addr = tbd_addr + sizeof(tbd); - - tx.tx_h.ac_status = 0; - tx.tx_h.ac_command = acmd_transmit | AC_CFLD_I; - tx.tx_h.ac_link = nop_addr; - tx.tx_tbd_offset = tbd_addr; - obram_write(ioaddr, tx_addr, (unsigned char *) &tx, - sizeof(tx)); - - nop.nop_h.ac_status = 0; - nop.nop_h.ac_command = acmd_nop; - nop.nop_h.ac_link = nop_addr; - obram_write(ioaddr, nop_addr, (unsigned char *) &nop, - sizeof(nop)); - - tbd.tbd_status = TBD_STATUS_EOF; - tbd.tbd_next_bd_offset = I82586NULL; - tbd.tbd_bufl = buf_addr; - tbd.tbd_bufh = 0; - obram_write(ioaddr, tbd_addr, (unsigned char *) &tbd, - sizeof(tbd)); - } - - first_nop = - OFFSET_CU + (NTXBLOCKS - 1) * TXBLOCKZ + sizeof(ac_tx_t); - obram_write(ioaddr, scboff(OFFSET_SCB, scb_cbl_offset), - (unsigned char *) &first_nop, sizeof(first_nop)); - - scb_cs = SCB_CMD_CUC_GO; - obram_write(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - - set_chan_attn(ioaddr, lp->hacr); - - for (i = 1000; i > 0; i--) { - obram_read(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cs, sizeof(scb_cs)); - if (scb_cs == 0) - break; - - udelay(10); - } - - if (i <= 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wavelan_cu_start(): board not accepting command.\n", - dev->name); -#endif - return -1; - } - - lp->tx_n_in_use = 0; - netif_start_queue(dev); -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_cu_start()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * This routine does a standard configuration of the WaveLAN - * controller (i82586). - * - * It initialises the scp, iscp and scb structure - * The first two are just pointers to the next. - * The last one is used for basic configuration and for basic - * communication (interrupt status). - * - * (called by wv_hw_reset()) - */ -static int wv_82586_start(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - scp_t scp; /* system configuration pointer */ - iscp_t iscp; /* intermediate scp */ - scb_t scb; /* system control block */ - ach_t cb; /* Action command header */ - u8 zeroes[512]; - int i; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_82586_start()\n", dev->name); -#endif - - /* - * Clear the onboard RAM. - */ - memset(&zeroes[0], 0x00, sizeof(zeroes)); - for (i = 0; i < I82586_MEMZ; i += sizeof(zeroes)) - obram_write(ioaddr, i, &zeroes[0], sizeof(zeroes)); - - /* - * Construct the command unit structures: - * scp, iscp, scb, cb. - */ - memset(&scp, 0x00, sizeof(scp)); - scp.scp_sysbus = SCP_SY_16BBUS; - scp.scp_iscpl = OFFSET_ISCP; - obram_write(ioaddr, OFFSET_SCP, (unsigned char *) &scp, - sizeof(scp)); - - memset(&iscp, 0x00, sizeof(iscp)); - iscp.iscp_busy = 1; - iscp.iscp_offset = OFFSET_SCB; - obram_write(ioaddr, OFFSET_ISCP, (unsigned char *) &iscp, - sizeof(iscp)); - - /* Our first command is to reset the i82586. */ - memset(&scb, 0x00, sizeof(scb)); - scb.scb_command = SCB_CMD_RESET; - scb.scb_cbl_offset = OFFSET_CU; - scb.scb_rfa_offset = OFFSET_RU; - obram_write(ioaddr, OFFSET_SCB, (unsigned char *) &scb, - sizeof(scb)); - - set_chan_attn(ioaddr, lp->hacr); - - /* Wait for command to finish. */ - for (i = 1000; i > 0; i--) { - obram_read(ioaddr, OFFSET_ISCP, (unsigned char *) &iscp, - sizeof(iscp)); - - if (iscp.iscp_busy == (unsigned short) 0) - break; - - udelay(10); - } - - if (i <= 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wv_82586_start(): iscp_busy timeout.\n", - dev->name); -#endif - return -1; - } - - /* Check command completion. */ - for (i = 15; i > 0; i--) { - obram_read(ioaddr, OFFSET_SCB, (unsigned char *) &scb, - sizeof(scb)); - - if (scb.scb_status == (SCB_ST_CX | SCB_ST_CNA)) - break; - - udelay(10); - } - - if (i <= 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wv_82586_start(): status: expected 0x%02x, got 0x%02x.\n", - dev->name, SCB_ST_CX | SCB_ST_CNA, scb.scb_status); -#endif - return -1; - } - - wv_ack(dev); - - /* Set the action command header. */ - memset(&cb, 0x00, sizeof(cb)); - cb.ac_command = AC_CFLD_EL | (AC_CFLD_CMD & acmd_diagnose); - cb.ac_link = OFFSET_CU; - obram_write(ioaddr, OFFSET_CU, (unsigned char *) &cb, sizeof(cb)); - - if (wv_synchronous_cmd(dev, "diag()") == -1) - return -1; - - obram_read(ioaddr, OFFSET_CU, (unsigned char *) &cb, sizeof(cb)); - if (cb.ac_status & AC_SFLD_FAIL) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wv_82586_start(): i82586 Self Test failed.\n", - dev->name); -#endif - return -1; - } -#ifdef DEBUG_I82586_SHOW - wv_scb_show(ioaddr); -#endif - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_82586_start()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * This routine does a standard configuration of the WaveLAN - * controller (i82586). - * - * This routine is a violent hack. We use the first free transmit block - * to make our configuration. In the buffer area, we create the three - * configuration commands (linked). We make the previous NOP point to - * the beginning of the buffer instead of the tx command. After, we go - * as usual to the NOP command. - * Note that only the last command (mc_set) will generate an interrupt. - * - * (called by wv_hw_reset(), wv_82586_reconfig(), wavelan_packet_xmit()) - */ -static void wv_82586_config(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - unsigned short txblock; - unsigned short txpred; - unsigned short tx_addr; - unsigned short nop_addr; - unsigned short tbd_addr; - unsigned short cfg_addr; - unsigned short ias_addr; - unsigned short mcs_addr; - ac_tx_t tx; - ac_nop_t nop; - ac_cfg_t cfg; /* Configure action */ - ac_ias_t ias; /* IA-setup action */ - ac_mcs_t mcs; /* Multicast setup */ - struct dev_mc_list *dmi; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_82586_config()\n", dev->name); -#endif - - /* Check nothing bad has happened */ - if (lp->tx_n_in_use == (NTXBLOCKS - 1)) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO "%s: wv_82586_config(): Tx queue full.\n", - dev->name); -#endif - return; - } - - /* Calculate addresses of next block and previous block. */ - txblock = lp->tx_first_free; - txpred = txblock - TXBLOCKZ; - if (txpred < OFFSET_CU) - txpred += NTXBLOCKS * TXBLOCKZ; - lp->tx_first_free += TXBLOCKZ; - if (lp->tx_first_free >= OFFSET_CU + NTXBLOCKS * TXBLOCKZ) - lp->tx_first_free -= NTXBLOCKS * TXBLOCKZ; - - lp->tx_n_in_use++; - - /* Calculate addresses of the different parts of the block. */ - tx_addr = txblock; - nop_addr = tx_addr + sizeof(tx); - tbd_addr = nop_addr + sizeof(nop); - cfg_addr = tbd_addr + sizeof(tbd_t); /* beginning of the buffer */ - ias_addr = cfg_addr + sizeof(cfg); - mcs_addr = ias_addr + sizeof(ias); - - /* - * Transmit command - */ - tx.tx_h.ac_status = 0xFFFF; /* Fake completion value */ - obram_write(ioaddr, toff(ac_tx_t, tx_addr, tx_h.ac_status), - (unsigned char *) &tx.tx_h.ac_status, - sizeof(tx.tx_h.ac_status)); - - /* - * NOP command - */ - nop.nop_h.ac_status = 0; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status), - (unsigned char *) &nop.nop_h.ac_status, - sizeof(nop.nop_h.ac_status)); - nop.nop_h.ac_link = nop_addr; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link), - (unsigned char *) &nop.nop_h.ac_link, - sizeof(nop.nop_h.ac_link)); - - /* Create a configure action. */ - memset(&cfg, 0x00, sizeof(cfg)); - - /* - * For Linux we invert AC_CFG_ALOC() so as to conform - * to the way that net packets reach us from above. - * (See also ac_tx_t.) - * - * Updated from Wavelan Manual WCIN085B - */ - cfg.cfg_byte_cnt = - AC_CFG_BYTE_CNT(sizeof(ac_cfg_t) - sizeof(ach_t)); - cfg.cfg_fifolim = AC_CFG_FIFOLIM(4); - cfg.cfg_byte8 = AC_CFG_SAV_BF(1) | AC_CFG_SRDY(0); - cfg.cfg_byte9 = AC_CFG_ELPBCK(0) | - AC_CFG_ILPBCK(0) | - AC_CFG_PRELEN(AC_CFG_PLEN_2) | - AC_CFG_ALOC(1) | AC_CFG_ADDRLEN(WAVELAN_ADDR_SIZE); - cfg.cfg_byte10 = AC_CFG_BOFMET(1) | - AC_CFG_ACR(6) | AC_CFG_LINPRIO(0); - cfg.cfg_ifs = 0x20; - cfg.cfg_slotl = 0x0C; - cfg.cfg_byte13 = AC_CFG_RETRYNUM(15) | AC_CFG_SLTTMHI(0); - cfg.cfg_byte14 = AC_CFG_FLGPAD(0) | - AC_CFG_BTSTF(0) | - AC_CFG_CRC16(0) | - AC_CFG_NCRC(0) | - AC_CFG_TNCRS(1) | - AC_CFG_MANCH(0) | - AC_CFG_BCDIS(0) | AC_CFG_PRM(lp->promiscuous); - cfg.cfg_byte15 = AC_CFG_ICDS(0) | - AC_CFG_CDTF(0) | AC_CFG_ICSS(0) | AC_CFG_CSTF(0); -/* - cfg.cfg_min_frm_len = AC_CFG_MNFRM(64); -*/ - cfg.cfg_min_frm_len = AC_CFG_MNFRM(8); - - cfg.cfg_h.ac_command = (AC_CFLD_CMD & acmd_configure); - cfg.cfg_h.ac_link = ias_addr; - obram_write(ioaddr, cfg_addr, (unsigned char *) &cfg, sizeof(cfg)); - - /* Set up the MAC address */ - memset(&ias, 0x00, sizeof(ias)); - ias.ias_h.ac_command = (AC_CFLD_CMD & acmd_ia_setup); - ias.ias_h.ac_link = mcs_addr; - memcpy(&ias.ias_addr[0], (unsigned char *) &dev->dev_addr[0], - sizeof(ias.ias_addr)); - obram_write(ioaddr, ias_addr, (unsigned char *) &ias, sizeof(ias)); - - /* Initialize adapter's Ethernet multicast addresses */ - memset(&mcs, 0x00, sizeof(mcs)); - mcs.mcs_h.ac_command = AC_CFLD_I | (AC_CFLD_CMD & acmd_mc_setup); - mcs.mcs_h.ac_link = nop_addr; - mcs.mcs_cnt = WAVELAN_ADDR_SIZE * lp->mc_count; - obram_write(ioaddr, mcs_addr, (unsigned char *) &mcs, sizeof(mcs)); - - /* Any address to set? */ - if (lp->mc_count) { - for (dmi = dev->mc_list; dmi; dmi = dmi->next) - outsw(PIOP1(ioaddr), (u16 *) dmi->dmi_addr, - WAVELAN_ADDR_SIZE >> 1); - -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG - "%s: wv_82586_config(): set %d multicast addresses:\n", - dev->name, lp->mc_count); - for (dmi = dev->mc_list; dmi; dmi = dmi->next) - printk(KERN_DEBUG " %pM\n", dmi->dmi_addr); -#endif - } - - /* - * Overwrite the predecessor NOP link - * so that it points to the configure action. - */ - nop_addr = txpred + sizeof(tx); - nop.nop_h.ac_status = 0; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status), - (unsigned char *) &nop.nop_h.ac_status, - sizeof(nop.nop_h.ac_status)); - nop.nop_h.ac_link = cfg_addr; - obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link), - (unsigned char *) &nop.nop_h.ac_link, - sizeof(nop.nop_h.ac_link)); - - /* Job done, clear the flag */ - lp->reconfig_82586 = 0; - - if (lp->tx_first_in_use == I82586NULL) - lp->tx_first_in_use = txblock; - - if (lp->tx_n_in_use == (NTXBLOCKS - 1)) - netif_stop_queue(dev); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_82586_config()\n", dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * This routine, called by wavelan_close(), gracefully stops the - * WaveLAN controller (i82586). - * (called by wavelan_close()) - */ -static void wv_82586_stop(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - u16 scb_cmd; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_82586_stop()\n", dev->name); -#endif - - /* Suspend both command unit and receive unit. */ - scb_cmd = - (SCB_CMD_CUC & SCB_CMD_CUC_SUS) | (SCB_CMD_RUC & - SCB_CMD_RUC_SUS); - obram_write(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &scb_cmd, sizeof(scb_cmd)); - set_chan_attn(ioaddr, lp->hacr); - - /* No more interrupts */ - wv_ints_off(dev); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_82586_stop()\n", dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * Totally reset the WaveLAN and restart it. - * Performs the following actions: - * 1. A power reset (reset DMA) - * 2. Initialize the radio modem (using wv_mmc_init) - * 3. Reset & Configure LAN controller (using wv_82586_start) - * 4. Start the LAN controller's command unit - * 5. Start the LAN controller's receive unit - * (called by wavelan_interrupt(), wavelan_watchdog() & wavelan_open()) - */ -static int wv_hw_reset(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_hw_reset(dev=0x%x)\n", dev->name, - (unsigned int) dev); -#endif - - /* Increase the number of resets done. */ - lp->nresets++; - - wv_hacr_reset(ioaddr); - lp->hacr = HACR_DEFAULT; - - if ((wv_mmc_init(dev) < 0) || (wv_82586_start(dev) < 0)) - return -1; - - /* Enable the card to send interrupts. */ - wv_ints_on(dev); - - /* Start card functions */ - if (wv_cu_start(dev) < 0) - return -1; - - /* Setup the controller and parameters */ - wv_82586_config(dev); - - /* Finish configuration with the receive unit */ - if (wv_ru_start(dev) < 0) - return -1; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_hw_reset()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Check if there is a WaveLAN at the specific base address. - * As a side effect, this reads the MAC address. - * (called in wavelan_probe() and init_module()) - */ -static int wv_check_ioaddr(unsigned long ioaddr, u8 * mac) -{ - int i; /* Loop counter */ - - /* Check if the base address if available. */ - if (!request_region(ioaddr, sizeof(ha_t), "wavelan probe")) - return -EBUSY; /* ioaddr already used */ - - /* Reset host interface */ - wv_hacr_reset(ioaddr); - - /* Read the MAC address from the parameter storage area. */ - psa_read(ioaddr, HACR_DEFAULT, psaoff(0, psa_univ_mac_addr), - mac, 6); - - release_region(ioaddr, sizeof(ha_t)); - - /* - * Check the first three octets of the address for the manufacturer's code. - * Note: if this can't find your WaveLAN card, you've got a - * non-NCR/AT&T/Lucent ISA card. See wavelan.p.h for detail on - * how to configure your card. - */ - for (i = 0; i < ARRAY_SIZE(MAC_ADDRESSES); i++) - if ((mac[0] == MAC_ADDRESSES[i][0]) && - (mac[1] == MAC_ADDRESSES[i][1]) && - (mac[2] == MAC_ADDRESSES[i][2])) - return 0; - -#ifdef DEBUG_CONFIG_INFO - printk(KERN_WARNING - "WaveLAN (0x%3X): your MAC address might be %02X:%02X:%02X.\n", - ioaddr, mac[0], mac[1], mac[2]); -#endif - return -ENODEV; -} - -/************************ INTERRUPT HANDLING ************************/ - -/* - * This function is the interrupt handler for the WaveLAN card. This - * routine will be called whenever: - */ -static irqreturn_t wavelan_interrupt(int irq, void *dev_id) -{ - struct net_device *dev; - unsigned long ioaddr; - net_local *lp; - u16 hasr; - u16 status; - u16 ack_cmd; - - dev = dev_id; - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: ->wavelan_interrupt()\n", dev->name); -#endif - - lp = netdev_priv(dev); - ioaddr = dev->base_addr; - -#ifdef DEBUG_INTERRUPT_INFO - /* Check state of our spinlock */ - if(spin_is_locked(&lp->spinlock)) - printk(KERN_DEBUG - "%s: wavelan_interrupt(): spinlock is already locked !!!\n", - dev->name); -#endif - - /* Prevent reentrancy. We need to do that because we may have - * multiple interrupt handler running concurrently. - * It is safe because interrupts are disabled before acquiring - * the spinlock. */ - spin_lock(&lp->spinlock); - - /* We always had spurious interrupts at startup, but lately I - * saw them comming *between* the request_irq() and the - * spin_lock_irqsave() in wavelan_open(), so the spinlock - * protection is no enough. - * So, we also check lp->hacr that will tell us is we enabled - * irqs or not (see wv_ints_on()). - * We can't use netif_running(dev) because we depend on the - * proper processing of the irq generated during the config. */ - - /* Which interrupt it is ? */ - hasr = hasr_read(ioaddr); - -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_INFO - "%s: wavelan_interrupt(): hasr 0x%04x; hacr 0x%04x.\n", - dev->name, hasr, lp->hacr); -#endif - - /* Check modem interrupt */ - if ((hasr & HASR_MMC_INTR) && (lp->hacr & HACR_MMC_INT_ENABLE)) { - u8 dce_status; - - /* - * Interrupt from the modem management controller. - * This will clear it -- ignored for now. - */ - mmc_read(ioaddr, mmroff(0, mmr_dce_status), &dce_status, - sizeof(dce_status)); - -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO - "%s: wavelan_interrupt(): unexpected mmc interrupt: status 0x%04x.\n", - dev->name, dce_status); -#endif - } - - /* Check if not controller interrupt */ - if (((hasr & HASR_82586_INTR) == 0) || - ((lp->hacr & HACR_82586_INT_ENABLE) == 0)) { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO - "%s: wavelan_interrupt(): interrupt not coming from i82586 - hasr 0x%04x.\n", - dev->name, hasr); -#endif - spin_unlock (&lp->spinlock); - return IRQ_NONE; - } - - /* Read interrupt data. */ - obram_read(ioaddr, scboff(OFFSET_SCB, scb_status), - (unsigned char *) &status, sizeof(status)); - - /* - * Acknowledge the interrupt(s). - */ - ack_cmd = status & SCB_ST_INT; - obram_write(ioaddr, scboff(OFFSET_SCB, scb_command), - (unsigned char *) &ack_cmd, sizeof(ack_cmd)); - set_chan_attn(ioaddr, lp->hacr); - -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG "%s: wavelan_interrupt(): status 0x%04x.\n", - dev->name, status); -#endif - - /* Command completed. */ - if ((status & SCB_ST_CX) == SCB_ST_CX) { -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG - "%s: wavelan_interrupt(): command completed.\n", - dev->name); -#endif - wv_complete(dev, ioaddr, lp); - } - - /* Frame received. */ - if ((status & SCB_ST_FR) == SCB_ST_FR) { -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG - "%s: wavelan_interrupt(): received packet.\n", - dev->name); -#endif - wv_receive(dev); - } - - /* Check the state of the command unit. */ - if (((status & SCB_ST_CNA) == SCB_ST_CNA) || - (((status & SCB_ST_CUS) != SCB_ST_CUS_ACTV) && - (netif_running(dev)))) { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO - "%s: wavelan_interrupt(): CU inactive -- restarting\n", - dev->name); -#endif - wv_hw_reset(dev); - } - - /* Check the state of the command unit. */ - if (((status & SCB_ST_RNR) == SCB_ST_RNR) || - (((status & SCB_ST_RUS) != SCB_ST_RUS_RDY) && - (netif_running(dev)))) { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO - "%s: wavelan_interrupt(): RU not ready -- restarting\n", - dev->name); -#endif - wv_hw_reset(dev); - } - - /* Release spinlock */ - spin_unlock (&lp->spinlock); - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: <-wavelan_interrupt()\n", dev->name); -#endif - return IRQ_HANDLED; -} - -/*------------------------------------------------------------------*/ -/* - * Watchdog: when we start a transmission, a timer is set for us in the - * kernel. If the transmission completes, this timer is disabled. If - * the timer expires, we are called and we try to unlock the hardware. - */ -static void wavelan_watchdog(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - u_long ioaddr = dev->base_addr; - unsigned long flags; - unsigned int nreaped; - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: ->wavelan_watchdog()\n", dev->name); -#endif - -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "%s: wavelan_watchdog: watchdog timer expired\n", - dev->name); -#endif - - /* Check that we came here for something */ - if (lp->tx_n_in_use <= 0) { - return; - } - - spin_lock_irqsave(&lp->spinlock, flags); - - /* Try to see if some buffers are not free (in case we missed - * an interrupt */ - nreaped = wv_complete(dev, ioaddr, lp); - -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG - "%s: wavelan_watchdog(): %d reaped, %d remain.\n", - dev->name, nreaped, lp->tx_n_in_use); -#endif - -#ifdef DEBUG_PSA_SHOW - { - psa_t psa; - psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa)); - wv_psa_show(&psa); - } -#endif -#ifdef DEBUG_MMC_SHOW - wv_mmc_show(dev); -#endif -#ifdef DEBUG_I82586_SHOW - wv_cu_show(dev); -#endif - - /* If no buffer has been freed */ - if (nreaped == 0) { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO - "%s: wavelan_watchdog(): cleanup failed, trying reset\n", - dev->name); -#endif - wv_hw_reset(dev); - } - - /* At this point, we should have some free Tx buffer ;-) */ - if (lp->tx_n_in_use < NTXBLOCKS - 1) - netif_wake_queue(dev); - - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: <-wavelan_watchdog()\n", dev->name); -#endif -} - -/********************* CONFIGURATION CALLBACKS *********************/ -/* - * Here are the functions called by the Linux networking code (NET3) - * for initialization, configuration and deinstallations of the - * WaveLAN ISA hardware. - */ - -/*------------------------------------------------------------------*/ -/* - * Configure and start up the WaveLAN PCMCIA adaptor. - * Called by NET3 when it "opens" the device. - */ -static int wavelan_open(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: ->wavelan_open(dev=0x%x)\n", dev->name, - (unsigned int) dev); -#endif - - /* Check irq */ - if (dev->irq == 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_WARNING "%s: wavelan_open(): no IRQ\n", - dev->name); -#endif - return -ENXIO; - } - - if (request_irq(dev->irq, &wavelan_interrupt, 0, "WaveLAN", dev) != 0) - { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_WARNING "%s: wavelan_open(): invalid IRQ\n", - dev->name); -#endif - return -EAGAIN; - } - - spin_lock_irqsave(&lp->spinlock, flags); - - if (wv_hw_reset(dev) != -1) { - netif_start_queue(dev); - } else { - free_irq(dev->irq, dev); -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wavelan_open(): impossible to start the card\n", - dev->name); -#endif - spin_unlock_irqrestore(&lp->spinlock, flags); - return -EAGAIN; - } - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: <-wavelan_open()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Shut down the WaveLAN ISA card. - * Called by NET3 when it "closes" the device. - */ -static int wavelan_close(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: ->wavelan_close(dev=0x%x)\n", dev->name, - (unsigned int) dev); -#endif - - netif_stop_queue(dev); - - /* - * Flush the Tx and disable Rx. - */ - spin_lock_irqsave(&lp->spinlock, flags); - wv_82586_stop(dev); - spin_unlock_irqrestore(&lp->spinlock, flags); - - free_irq(dev->irq, dev); - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: <-wavelan_close()\n", dev->name); -#endif - return 0; -} - -static const struct net_device_ops wavelan_netdev_ops = { - .ndo_open = wavelan_open, - .ndo_stop = wavelan_close, - .ndo_start_xmit = wavelan_packet_xmit, - .ndo_set_multicast_list = wavelan_set_multicast_list, - .ndo_tx_timeout = wavelan_watchdog, - .ndo_change_mtu = eth_change_mtu, - .ndo_validate_addr = eth_validate_addr, -#ifdef SET_MAC_ADDRESS - .ndo_set_mac_address = wavelan_set_mac_address -#else - .ndo_set_mac_address = eth_mac_addr, -#endif -}; - - -/*------------------------------------------------------------------*/ -/* - * Probe an I/O address, and if the WaveLAN is there configure the - * device structure - * (called by wavelan_probe() and via init_module()). - */ -static int __init wavelan_config(struct net_device *dev, unsigned short ioaddr) -{ - u8 irq_mask; - int irq; - net_local *lp; - mac_addr mac; - int err; - - if (!request_region(ioaddr, sizeof(ha_t), "wavelan")) - return -EADDRINUSE; - - err = wv_check_ioaddr(ioaddr, mac); - if (err) - goto out; - - memcpy(dev->dev_addr, mac, 6); - - dev->base_addr = ioaddr; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: ->wavelan_config(dev=0x%x, ioaddr=0x%lx)\n", - dev->name, (unsigned int) dev, ioaddr); -#endif - - /* Check IRQ argument on command line. */ - if (dev->irq != 0) { - irq_mask = wv_irq_to_psa(dev->irq); - - if (irq_mask == 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_WARNING - "%s: wavelan_config(): invalid IRQ %d ignored.\n", - dev->name, dev->irq); -#endif - dev->irq = 0; - } else { -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG - "%s: wavelan_config(): changing IRQ to %d\n", - dev->name, dev->irq); -#endif - psa_write(ioaddr, HACR_DEFAULT, - psaoff(0, psa_int_req_no), &irq_mask, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev, ioaddr, HACR_DEFAULT); - wv_hacr_reset(ioaddr); - } - } - - psa_read(ioaddr, HACR_DEFAULT, psaoff(0, psa_int_req_no), - &irq_mask, 1); - if ((irq = wv_psa_to_irq(irq_mask)) == -1) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_INFO - "%s: wavelan_config(): could not wavelan_map_irq(%d).\n", - dev->name, irq_mask); -#endif - err = -EAGAIN; - goto out; - } - - dev->irq = irq; - - dev->mem_start = 0x0000; - dev->mem_end = 0x0000; - dev->if_port = 0; - - /* Initialize device structures */ - memset(netdev_priv(dev), 0, sizeof(net_local)); - lp = netdev_priv(dev); - - /* Back link to the device structure. */ - lp->dev = dev; - /* Add the device at the beginning of the linked list. */ - lp->next = wavelan_list; - wavelan_list = lp; - - lp->hacr = HACR_DEFAULT; - - /* Multicast stuff */ - lp->promiscuous = 0; - lp->mc_count = 0; - - /* Init spinlock */ - spin_lock_init(&lp->spinlock); - - dev->netdev_ops = &wavelan_netdev_ops; - dev->watchdog_timeo = WATCHDOG_JIFFIES; - dev->wireless_handlers = &wavelan_handler_def; - lp->wireless_data.spy_data = &lp->spy_data; - dev->wireless_data = &lp->wireless_data; - - dev->mtu = WAVELAN_MTU; - - /* Display nice information. */ - wv_init_info(dev); - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: <-wavelan_config()\n", dev->name); -#endif - return 0; -out: - release_region(ioaddr, sizeof(ha_t)); - return err; -} - -/*------------------------------------------------------------------*/ -/* - * Check for a network adaptor of this type. Return '0' iff one - * exists. There seem to be different interpretations of - * the initial value of dev->base_addr. - * We follow the example in drivers/net/ne.c. - * (called in "Space.c") - */ -struct net_device * __init wavelan_probe(int unit) -{ - struct net_device *dev; - short base_addr; - int def_irq; - int i; - int r = 0; - - /* compile-time check the sizes of structures */ - BUILD_BUG_ON(sizeof(psa_t) != PSA_SIZE); - BUILD_BUG_ON(sizeof(mmw_t) != MMW_SIZE); - BUILD_BUG_ON(sizeof(mmr_t) != MMR_SIZE); - BUILD_BUG_ON(sizeof(ha_t) != HA_SIZE); - - dev = alloc_etherdev(sizeof(net_local)); - if (!dev) - return ERR_PTR(-ENOMEM); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - base_addr = dev->base_addr; - def_irq = dev->irq; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG - "%s: ->wavelan_probe(dev=%p (base_addr=0x%x))\n", - dev->name, dev, (unsigned int) dev->base_addr); -#endif - - /* Don't probe at all. */ - if (base_addr < 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_WARNING - "%s: wavelan_probe(): invalid base address\n", - dev->name); -#endif - r = -ENXIO; - } else if (base_addr > 0x100) { /* Check a single specified location. */ - r = wavelan_config(dev, base_addr); -#ifdef DEBUG_CONFIG_INFO - if (r != 0) - printk(KERN_DEBUG - "%s: wavelan_probe(): no device at specified base address (0x%X) or address already in use\n", - dev->name, base_addr); -#endif - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: <-wavelan_probe()\n", dev->name); -#endif - } else { /* Scan all possible addresses of the WaveLAN hardware. */ - for (i = 0; i < ARRAY_SIZE(iobase); i++) { - dev->irq = def_irq; - if (wavelan_config(dev, iobase[i]) == 0) { -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG - "%s: <-wavelan_probe()\n", - dev->name); -#endif - break; - } - } - if (i == ARRAY_SIZE(iobase)) - r = -ENODEV; - } - if (r) - goto out; - r = register_netdev(dev); - if (r) - goto out1; - return dev; -out1: - release_region(dev->base_addr, sizeof(ha_t)); - wavelan_list = wavelan_list->next; -out: - free_netdev(dev); - return ERR_PTR(r); -} - -/****************************** MODULE ******************************/ -/* - * Module entry point: insertion and removal - */ - -#ifdef MODULE -/*------------------------------------------------------------------*/ -/* - * Insertion of the module - * I'm now quite proud of the multi-device support. - */ -int __init init_module(void) -{ - int ret = -EIO; /* Return error if no cards found */ - int i; - -#ifdef DEBUG_MODULE_TRACE - printk(KERN_DEBUG "-> init_module()\n"); -#endif - - /* If probing is asked */ - if (io[0] == 0) { -#ifdef DEBUG_CONFIG_ERROR - printk(KERN_WARNING - "WaveLAN init_module(): doing device probing (bad !)\n"); - printk(KERN_WARNING - "Specify base addresses while loading module to correct the problem\n"); -#endif - - /* Copy the basic set of address to be probed. */ - for (i = 0; i < ARRAY_SIZE(iobase); i++) - io[i] = iobase[i]; - } - - - /* Loop on all possible base addresses. */ - for (i = 0; i < ARRAY_SIZE(io) && io[i] != 0; i++) { - struct net_device *dev = alloc_etherdev(sizeof(net_local)); - if (!dev) - break; - if (name[i]) - strcpy(dev->name, name[i]); /* Copy name */ - dev->base_addr = io[i]; - dev->irq = irq[i]; - - /* Check if there is something at this base address. */ - if (wavelan_config(dev, io[i]) == 0) { - if (register_netdev(dev) != 0) { - release_region(dev->base_addr, sizeof(ha_t)); - wavelan_list = wavelan_list->next; - } else { - ret = 0; - continue; - } - } - free_netdev(dev); - } - -#ifdef DEBUG_CONFIG_ERROR - if (!wavelan_list) - printk(KERN_WARNING - "WaveLAN init_module(): no device found\n"); -#endif - -#ifdef DEBUG_MODULE_TRACE - printk(KERN_DEBUG "<- init_module()\n"); -#endif - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Removal of the module - */ -void cleanup_module(void) -{ -#ifdef DEBUG_MODULE_TRACE - printk(KERN_DEBUG "-> cleanup_module()\n"); -#endif - - /* Loop on all devices and release them. */ - while (wavelan_list) { - struct net_device *dev = wavelan_list->dev; - -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG - "%s: cleanup_module(): removing device at 0x%x\n", - dev->name, (unsigned int) dev); -#endif - unregister_netdev(dev); - - release_region(dev->base_addr, sizeof(ha_t)); - wavelan_list = wavelan_list->next; - - free_netdev(dev); - } - -#ifdef DEBUG_MODULE_TRACE - printk(KERN_DEBUG "<- cleanup_module()\n"); -#endif -} -#endif /* MODULE */ -MODULE_LICENSE("GPL"); - -/* - * This software may only be used and distributed - * according to the terms of the GNU General Public License. - * - * This software was developed as a component of the - * Linux operating system. - * It is based on other device drivers and information - * either written or supplied by: - * Ajay Bakre (bakre@paul.rutgers.edu), - * Donald Becker (becker@scyld.com), - * Loeke Brederveld (Loeke.Brederveld@Utrecht.NCR.com), - * Anders Klemets (klemets@it.kth.se), - * Vladimir V. Kolpakov (w@stier.koenig.ru), - * Marc Meertens (Marc.Meertens@Utrecht.NCR.com), - * Pauline Middelink (middelin@polyware.iaf.nl), - * Robert Morris (rtm@das.harvard.edu), - * Jean Tourrilhes (jt@hplb.hpl.hp.com), - * Girish Welling (welling@paul.rutgers.edu), - * - * Thanks go also to: - * James Ashton (jaa101@syseng.anu.edu.au), - * Alan Cox (alan@lxorguk.ukuu.org.uk), - * Allan Creighton (allanc@cs.usyd.edu.au), - * Matthew Geier (matthew@cs.usyd.edu.au), - * Remo di Giovanni (remo@cs.usyd.edu.au), - * Eckhard Grah (grah@wrcs1.urz.uni-wuppertal.de), - * Vipul Gupta (vgupta@cs.binghamton.edu), - * Mark Hagan (mhagan@wtcpost.daytonoh.NCR.COM), - * Tim Nicholson (tim@cs.usyd.edu.au), - * Ian Parkin (ian@cs.usyd.edu.au), - * John Rosenberg (johnr@cs.usyd.edu.au), - * George Rossi (george@phm.gov.au), - * Arthur Scott (arthur@cs.usyd.edu.au), - * Peter Storey, - * for their assistance and advice. - * - * Please send bug reports, updates, comments to: - * - * Bruce Janson Email: bruce@cs.usyd.edu.au - * Basser Department of Computer Science Phone: +61-2-9351-3423 - * University of Sydney, N.S.W., 2006, AUSTRALIA Fax: +61-2-9351-3838 - */ diff --git a/drivers/net/wireless/wavelan.h b/drivers/net/wireless/wavelan.h deleted file mode 100644 index 9ab3605..0000000 --- a/drivers/net/wireless/wavelan.h +++ /dev/null @@ -1,370 +0,0 @@ -/* - * WaveLAN ISA driver - * - * Jean II - HPLB '96 - * - * Reorganisation and extension of the driver. - * Original copyright follows. See wavelan.p.h for details. - * - * This file contains the declarations for the WaveLAN hardware. Note that - * the WaveLAN ISA includes a i82586 controller (see definitions in - * file i82586.h). - * - * The main difference between the ISA hardware and the PCMCIA one is - * the Ethernet controller (i82586 instead of i82593). - * The i82586 allows multiple transmit buffers. The PSA needs to be accessed - * through the host interface. - */ - -#ifndef _WAVELAN_H -#define _WAVELAN_H - -/************************** MAGIC NUMBERS ***************************/ - -/* Detection of the WaveLAN card is done by reading the MAC - * address from the card and checking it. If you have a non-AT&T - * product (OEM, like DEC RoamAbout, Digital Ocean, or Epson), - * you might need to modify this part to accommodate your hardware. - */ -static const char MAC_ADDRESSES[][3] = -{ - { 0x08, 0x00, 0x0E }, /* AT&T WaveLAN (standard) & DEC RoamAbout */ - { 0x08, 0x00, 0x6A }, /* AT&T WaveLAN (alternate) */ - { 0x00, 0x00, 0xE1 }, /* Hitachi Wavelan */ - { 0x00, 0x60, 0x1D } /* Lucent Wavelan (another one) */ - /* Add your card here and send me the patch! */ -}; - -#define WAVELAN_ADDR_SIZE 6 /* Size of a MAC address */ - -#define WAVELAN_MTU 1500 /* Maximum size of WaveLAN packet */ - -#define MAXDATAZ (WAVELAN_ADDR_SIZE + WAVELAN_ADDR_SIZE + 2 + WAVELAN_MTU) - -/* - * Constants used to convert channels to frequencies - */ - -/* Frequency available in the 2.0 modem, in units of 250 kHz - * (as read in the offset register of the dac area). - * Used to map channel numbers used by `wfreqsel' to frequencies - */ -static const short channel_bands[] = { 0x30, 0x58, 0x64, 0x7A, 0x80, 0xA8, - 0xD0, 0xF0, 0xF8, 0x150 }; - -/* Frequencies of the 1.0 modem (fixed frequencies). - * Use to map the PSA `subband' to a frequency - * Note : all frequencies apart from the first one need to be multiplied by 10 - */ -static const int fixed_bands[] = { 915e6, 2.425e8, 2.46e8, 2.484e8, 2.4305e8 }; - - - -/*************************** PC INTERFACE ****************************/ - -/* - * Host Adaptor structure. - * (base is board port address). - */ -typedef union hacs_u hacs_u; -union hacs_u -{ - unsigned short hu_command; /* Command register */ -#define HACR_RESET 0x0001 /* Reset board */ -#define HACR_CA 0x0002 /* Set Channel Attention for 82586 */ -#define HACR_16BITS 0x0004 /* 16-bit operation (0 => 8bits) */ -#define HACR_OUT0 0x0008 /* General purpose output pin 0 */ - /* not used - must be 1 */ -#define HACR_OUT1 0x0010 /* General purpose output pin 1 */ - /* not used - must be 1 */ -#define HACR_82586_INT_ENABLE 0x0020 /* Enable 82586 interrupts */ -#define HACR_MMC_INT_ENABLE 0x0040 /* Enable MMC interrupts */ -#define HACR_INTR_CLR_ENABLE 0x0080 /* Enable interrupt status read/clear */ - unsigned short hu_status; /* Status Register */ -#define HASR_82586_INTR 0x0001 /* Interrupt request from 82586 */ -#define HASR_MMC_INTR 0x0002 /* Interrupt request from MMC */ -#define HASR_MMC_BUSY 0x0004 /* MMC busy indication */ -#define HASR_PSA_BUSY 0x0008 /* LAN parameter storage area busy */ -} __attribute__ ((packed)); - -typedef struct ha_t ha_t; -struct ha_t -{ - hacs_u ha_cs; /* Command and status registers */ -#define ha_command ha_cs.hu_command -#define ha_status ha_cs.hu_status - unsigned short ha_mmcr; /* Modem Management Ctrl Register */ - unsigned short ha_pior0; /* Program I/O Address Register Port 0 */ - unsigned short ha_piop0; /* Program I/O Port 0 */ - unsigned short ha_pior1; /* Program I/O Address Register Port 1 */ - unsigned short ha_piop1; /* Program I/O Port 1 */ - unsigned short ha_pior2; /* Program I/O Address Register Port 2 */ - unsigned short ha_piop2; /* Program I/O Port 2 */ -}; - -#define HA_SIZE 16 - -#define hoff(p,f) (unsigned short)((void *)(&((ha_t *)((void *)0 + (p)))->f) - (void *)0) -#define HACR(p) hoff(p, ha_command) -#define HASR(p) hoff(p, ha_status) -#define MMCR(p) hoff(p, ha_mmcr) -#define PIOR0(p) hoff(p, ha_pior0) -#define PIOP0(p) hoff(p, ha_piop0) -#define PIOR1(p) hoff(p, ha_pior1) -#define PIOP1(p) hoff(p, ha_piop1) -#define PIOR2(p) hoff(p, ha_pior2) -#define PIOP2(p) hoff(p, ha_piop2) - -/* - * Program I/O Mode Register values. - */ -#define STATIC_PIO 0 /* Mode 1: static mode */ - /* RAM access ??? */ -#define AUTOINCR_PIO 1 /* Mode 2: auto increment mode */ - /* RAM access ??? */ -#define AUTODECR_PIO 2 /* Mode 3: auto decrement mode */ - /* RAM access ??? */ -#define PARAM_ACCESS_PIO 3 /* Mode 4: LAN parameter access mode */ - /* Parameter access. */ -#define PIO_MASK 3 /* register mask */ -#define PIOM(cmd,piono) ((u_short)cmd << 10 << (piono * 2)) - -#define HACR_DEFAULT (HACR_OUT0 | HACR_OUT1 | HACR_16BITS | PIOM(STATIC_PIO, 0) | PIOM(AUTOINCR_PIO, 1) | PIOM(PARAM_ACCESS_PIO, 2)) -#define HACR_INTRON (HACR_82586_INT_ENABLE | HACR_MMC_INT_ENABLE | HACR_INTR_CLR_ENABLE) - -/************************** MEMORY LAYOUT **************************/ - -/* - * Onboard 64 k RAM layout. - * (Offsets from 0x0000.) - */ -#define OFFSET_RU 0x0000 /* 75% memory */ -#define OFFSET_CU 0xC000 /* 25% memory */ -#define OFFSET_SCB (OFFSET_ISCP - sizeof(scb_t)) -#define OFFSET_ISCP (OFFSET_SCP - sizeof(iscp_t)) -#define OFFSET_SCP I82586_SCP_ADDR - -#define RXBLOCKZ (sizeof(fd_t) + sizeof(rbd_t) + MAXDATAZ) -#define TXBLOCKZ (sizeof(ac_tx_t) + sizeof(ac_nop_t) + sizeof(tbd_t) + MAXDATAZ) - -#define NRXBLOCKS ((OFFSET_CU - OFFSET_RU) / RXBLOCKZ) -#define NTXBLOCKS ((OFFSET_SCB - OFFSET_CU) / TXBLOCKZ) - -/********************** PARAMETER STORAGE AREA **********************/ - -/* - * Parameter Storage Area (PSA). - */ -typedef struct psa_t psa_t; -struct psa_t -{ - unsigned char psa_io_base_addr_1; /* [0x00] Base address 1 ??? */ - unsigned char psa_io_base_addr_2; /* [0x01] Base address 2 */ - unsigned char psa_io_base_addr_3; /* [0x02] Base address 3 */ - unsigned char psa_io_base_addr_4; /* [0x03] Base address 4 */ - unsigned char psa_rem_boot_addr_1; /* [0x04] Remote Boot Address 1 */ - unsigned char psa_rem_boot_addr_2; /* [0x05] Remote Boot Address 2 */ - unsigned char psa_rem_boot_addr_3; /* [0x06] Remote Boot Address 3 */ - unsigned char psa_holi_params; /* [0x07] HOst Lan Interface (HOLI) Parameters */ - unsigned char psa_int_req_no; /* [0x08] Interrupt Request Line */ - unsigned char psa_unused0[7]; /* [0x09-0x0F] unused */ - - unsigned char psa_univ_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x10-0x15] Universal (factory) MAC Address */ - unsigned char psa_local_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x16-1B] Local MAC Address */ - unsigned char psa_univ_local_sel; /* [0x1C] Universal Local Selection */ -#define PSA_UNIVERSAL 0 /* Universal (factory) */ -#define PSA_LOCAL 1 /* Local */ - unsigned char psa_comp_number; /* [0x1D] Compatibility Number: */ -#define PSA_COMP_PC_AT_915 0 /* PC-AT 915 MHz */ -#define PSA_COMP_PC_MC_915 1 /* PC-MC 915 MHz */ -#define PSA_COMP_PC_AT_2400 2 /* PC-AT 2.4 GHz */ -#define PSA_COMP_PC_MC_2400 3 /* PC-MC 2.4 GHz */ -#define PSA_COMP_PCMCIA_915 4 /* PCMCIA 915 MHz or 2.0 */ - unsigned char psa_thr_pre_set; /* [0x1E] Modem Threshold Preset */ - unsigned char psa_feature_select; /* [0x1F] Call code required (1=on) */ -#define PSA_FEATURE_CALL_CODE 0x01 /* Call code required (Japan) */ - unsigned char psa_subband; /* [0x20] Subband */ -#define PSA_SUBBAND_915 0 /* 915 MHz or 2.0 */ -#define PSA_SUBBAND_2425 1 /* 2425 MHz */ -#define PSA_SUBBAND_2460 2 /* 2460 MHz */ -#define PSA_SUBBAND_2484 3 /* 2484 MHz */ -#define PSA_SUBBAND_2430_5 4 /* 2430.5 MHz */ - unsigned char psa_quality_thr; /* [0x21] Modem Quality Threshold */ - unsigned char psa_mod_delay; /* [0x22] Modem Delay (?) (reserved) */ - unsigned char psa_nwid[2]; /* [0x23-0x24] Network ID */ - unsigned char psa_nwid_select; /* [0x25] Network ID Select On/Off */ - unsigned char psa_encryption_select; /* [0x26] Encryption On/Off */ - unsigned char psa_encryption_key[8]; /* [0x27-0x2E] Encryption Key */ - unsigned char psa_databus_width; /* [0x2F] AT bus width select 8/16 */ - unsigned char psa_call_code[8]; /* [0x30-0x37] (Japan) Call Code */ - unsigned char psa_nwid_prefix[2]; /* [0x38-0x39] Roaming domain */ - unsigned char psa_reserved[2]; /* [0x3A-0x3B] Reserved - fixed 00 */ - unsigned char psa_conf_status; /* [0x3C] Conf Status, bit 0=1:config*/ - unsigned char psa_crc[2]; /* [0x3D] CRC-16 over PSA */ - unsigned char psa_crc_status; /* [0x3F] CRC Valid Flag */ -}; - -#define PSA_SIZE 64 - -/* Calculate offset of a field in the above structure. - * Warning: only even addresses are used. */ -#define psaoff(p,f) ((unsigned short) ((void *)(&((psa_t *) ((void *) NULL + (p)))->f) - (void *) NULL)) - -/******************** MODEM MANAGEMENT INTERFACE ********************/ - -/* - * Modem Management Controller (MMC) write structure. - */ -typedef struct mmw_t mmw_t; -struct mmw_t -{ - unsigned char mmw_encr_key[8]; /* encryption key */ - unsigned char mmw_encr_enable; /* Enable or disable encryption. */ -#define MMW_ENCR_ENABLE_MODE 0x02 /* mode of security option */ -#define MMW_ENCR_ENABLE_EN 0x01 /* Enable security option. */ - unsigned char mmw_unused0[1]; /* unused */ - unsigned char mmw_des_io_invert; /* encryption option */ -#define MMW_DES_IO_INVERT_RES 0x0F /* reserved */ -#define MMW_DES_IO_INVERT_CTRL 0xF0 /* control (?) (set to 0) */ - unsigned char mmw_unused1[5]; /* unused */ - unsigned char mmw_loopt_sel; /* looptest selection */ -#define MMW_LOOPT_SEL_DIS_NWID 0x40 /* Disable NWID filtering. */ -#define MMW_LOOPT_SEL_INT 0x20 /* Activate Attention Request. */ -#define MMW_LOOPT_SEL_LS 0x10 /* looptest, no collision avoidance */ -#define MMW_LOOPT_SEL_LT3A 0x08 /* looptest 3a */ -#define MMW_LOOPT_SEL_LT3B 0x04 /* looptest 3b */ -#define MMW_LOOPT_SEL_LT3C 0x02 /* looptest 3c */ -#define MMW_LOOPT_SEL_LT3D 0x01 /* looptest 3d */ - unsigned char mmw_jabber_enable; /* jabber timer enable */ - /* Abort transmissions > 200 ms */ - unsigned char mmw_freeze; /* freeze or unfreeze signal level */ - /* 0 : signal level & qual updated for every new message, 1 : frozen */ - unsigned char mmw_anten_sel; /* antenna selection */ -#define MMW_ANTEN_SEL_SEL 0x01 /* direct antenna selection */ -#define MMW_ANTEN_SEL_ALG_EN 0x02 /* antenna selection algo. enable */ - unsigned char mmw_ifs; /* inter frame spacing */ - /* min time between transmission in bit periods (.5 us) - bit 0 ignored */ - unsigned char mmw_mod_delay; /* modem delay (synchro) */ - unsigned char mmw_jam_time; /* jamming time (after collision) */ - unsigned char mmw_unused2[1]; /* unused */ - unsigned char mmw_thr_pre_set; /* level threshold preset */ - /* Discard all packet with signal < this value (4) */ - unsigned char mmw_decay_prm; /* decay parameters */ - unsigned char mmw_decay_updat_prm; /* decay update parameters */ - unsigned char mmw_quality_thr; /* quality (z-quotient) threshold */ - /* Discard all packet with quality < this value (3) */ - unsigned char mmw_netw_id_l; /* NWID low order byte */ - unsigned char mmw_netw_id_h; /* NWID high order byte */ - /* Network ID or Domain : create virtual net on the air */ - - /* 2.0 Hardware extension - frequency selection support */ - unsigned char mmw_mode_select; /* for analog tests (set to 0) */ - unsigned char mmw_unused3[1]; /* unused */ - unsigned char mmw_fee_ctrl; /* frequency EEPROM control */ -#define MMW_FEE_CTRL_PRE 0x10 /* Enable protected instructions. */ -#define MMW_FEE_CTRL_DWLD 0x08 /* Download EEPROM to mmc. */ -#define MMW_FEE_CTRL_CMD 0x07 /* EEPROM commands: */ -#define MMW_FEE_CTRL_READ 0x06 /* Read */ -#define MMW_FEE_CTRL_WREN 0x04 /* Write enable */ -#define MMW_FEE_CTRL_WRITE 0x05 /* Write data to address. */ -#define MMW_FEE_CTRL_WRALL 0x04 /* Write data to all addresses. */ -#define MMW_FEE_CTRL_WDS 0x04 /* Write disable */ -#define MMW_FEE_CTRL_PRREAD 0x16 /* Read addr from protect register */ -#define MMW_FEE_CTRL_PREN 0x14 /* Protect register enable */ -#define MMW_FEE_CTRL_PRCLEAR 0x17 /* Unprotect all registers. */ -#define MMW_FEE_CTRL_PRWRITE 0x15 /* Write address in protect register */ -#define MMW_FEE_CTRL_PRDS 0x14 /* Protect register disable */ - /* Never issue the PRDS command: it's irreversible! */ - - unsigned char mmw_fee_addr; /* EEPROM address */ -#define MMW_FEE_ADDR_CHANNEL 0xF0 /* Select the channel. */ -#define MMW_FEE_ADDR_OFFSET 0x0F /* Offset in channel data */ -#define MMW_FEE_ADDR_EN 0xC0 /* FEE_CTRL enable operations */ -#define MMW_FEE_ADDR_DS 0x00 /* FEE_CTRL disable operations */ -#define MMW_FEE_ADDR_ALL 0x40 /* FEE_CTRL all operations */ -#define MMW_FEE_ADDR_CLEAR 0xFF /* FEE_CTRL clear operations */ - - unsigned char mmw_fee_data_l; /* Write data to EEPROM. */ - unsigned char mmw_fee_data_h; /* high octet */ - unsigned char mmw_ext_ant; /* Setting for external antenna */ -#define MMW_EXT_ANT_EXTANT 0x01 /* Select external antenna */ -#define MMW_EXT_ANT_POL 0x02 /* Polarity of the antenna */ -#define MMW_EXT_ANT_INTERNAL 0x00 /* Internal antenna */ -#define MMW_EXT_ANT_EXTERNAL 0x03 /* External antenna */ -#define MMW_EXT_ANT_IQ_TEST 0x1C /* IQ test pattern (set to 0) */ -} __attribute__ ((packed)); - -#define MMW_SIZE 37 - -#define mmwoff(p,f) (unsigned short)((void *)(&((mmw_t *)((void *)0 + (p)))->f) - (void *)0) - -/* - * Modem Management Controller (MMC) read structure. - */ -typedef struct mmr_t mmr_t; -struct mmr_t -{ - unsigned char mmr_unused0[8]; /* unused */ - unsigned char mmr_des_status; /* encryption status */ - unsigned char mmr_des_avail; /* encryption available (0x55 read) */ -#define MMR_DES_AVAIL_DES 0x55 /* DES available */ -#define MMR_DES_AVAIL_AES 0x33 /* AES (AT&T) available */ - unsigned char mmr_des_io_invert; /* des I/O invert register */ - unsigned char mmr_unused1[5]; /* unused */ - unsigned char mmr_dce_status; /* DCE status */ -#define MMR_DCE_STATUS_RX_BUSY 0x01 /* receiver busy */ -#define MMR_DCE_STATUS_LOOPT_IND 0x02 /* loop test indicated */ -#define MMR_DCE_STATUS_TX_BUSY 0x04 /* transmitter on */ -#define MMR_DCE_STATUS_JBR_EXPIRED 0x08 /* jabber timer expired */ -#define MMR_DCE_STATUS 0x0F /* mask to get the bits */ - unsigned char mmr_dsp_id; /* DSP ID (AA = Daedalus rev A) */ - unsigned char mmr_unused2[2]; /* unused */ - unsigned char mmr_correct_nwid_l; /* # of correct NWIDs rxd (low) */ - unsigned char mmr_correct_nwid_h; /* # of correct NWIDs rxd (high) */ - /* Warning: read high-order octet first! */ - unsigned char mmr_wrong_nwid_l; /* # of wrong NWIDs rxd (low) */ - unsigned char mmr_wrong_nwid_h; /* # of wrong NWIDs rxd (high) */ - unsigned char mmr_thr_pre_set; /* level threshold preset */ -#define MMR_THR_PRE_SET 0x3F /* level threshold preset */ -#define MMR_THR_PRE_SET_CUR 0x80 /* Current signal above it */ - unsigned char mmr_signal_lvl; /* signal level */ -#define MMR_SIGNAL_LVL 0x3F /* signal level */ -#define MMR_SIGNAL_LVL_VALID 0x80 /* Updated since last read */ - unsigned char mmr_silence_lvl; /* silence level (noise) */ -#define MMR_SILENCE_LVL 0x3F /* silence level */ -#define MMR_SILENCE_LVL_VALID 0x80 /* Updated since last read */ - unsigned char mmr_sgnl_qual; /* signal quality */ -#define MMR_SGNL_QUAL 0x0F /* signal quality */ -#define MMR_SGNL_QUAL_ANT 0x80 /* current antenna used */ - unsigned char mmr_netw_id_l; /* NWID low order byte (?) */ - unsigned char mmr_unused3[3]; /* unused */ - - /* 2.0 Hardware extension - frequency selection support */ - unsigned char mmr_fee_status; /* Status of frequency EEPROM */ -#define MMR_FEE_STATUS_ID 0xF0 /* Modem revision ID */ -#define MMR_FEE_STATUS_DWLD 0x08 /* Download in progress */ -#define MMR_FEE_STATUS_BUSY 0x04 /* EEPROM busy */ - unsigned char mmr_unused4[1]; /* unused */ - unsigned char mmr_fee_data_l; /* Read data from EEPROM (low) */ - unsigned char mmr_fee_data_h; /* Read data from EEPROM (high) */ -} __attribute__ ((packed)); - -#define MMR_SIZE 36 - -#define mmroff(p,f) (unsigned short)((void *)(&((mmr_t *)((void *)0 + (p)))->f) - (void *)0) - -/* Make the two above structures one */ -typedef union mm_t -{ - struct mmw_t w; /* Write to the mmc */ - struct mmr_t r; /* Read from the mmc */ -} mm_t; - -#endif /* _WAVELAN_H */ - -/* - * This software may only be used and distributed - * according to the terms of the GNU General Public License. - * - * For more details, see wavelan.c. - */ diff --git a/drivers/net/wireless/wavelan.p.h b/drivers/net/wireless/wavelan.p.h deleted file mode 100644 index dbe8de6..0000000 --- a/drivers/net/wireless/wavelan.p.h +++ /dev/null @@ -1,696 +0,0 @@ -/* - * WaveLAN ISA driver - * - * Jean II - HPLB '96 - * - * Reorganisation and extension of the driver. - * - * This file contains all definitions and declarations necessary for the - * WaveLAN ISA driver. This file is a private header, so it should - * be included only in wavelan.c! - */ - -#ifndef WAVELAN_P_H -#define WAVELAN_P_H - -/************************** DOCUMENTATION ***************************/ -/* - * This driver provides a Linux interface to the WaveLAN ISA hardware. - * The WaveLAN is a product of Lucent (http://www.wavelan.com/). - * This division was formerly part of NCR and then AT&T. - * WaveLANs are also distributed by DEC (RoamAbout DS) and Digital Ocean. - * - * To learn how to use this driver, read the NET3 HOWTO. - * If you want to exploit the many other functionalities, read the comments - * in the code. - * - * This driver is the result of the effort of many people (see below). - */ - -/* ------------------------ SPECIFIC NOTES ------------------------ */ -/* - * Web page - * -------- - * I try to maintain a web page with the Wireless LAN Howto at : - * http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Wavelan.html - * - * SMP - * --- - * We now are SMP compliant (I eventually fixed the remaining bugs). - * The driver has been tested on a dual P6-150 and survived my usual - * set of torture tests. - * Anyway, I spent enough time chasing interrupt re-entrancy during - * errors or reconfigure, and I designed the locked/unlocked sections - * of the driver with great care, and with the recent addition of - * the spinlock (thanks to the new API), we should be quite close to - * the truth. - * The SMP/IRQ locking is quite coarse and conservative (i.e. not fast), - * but better safe than sorry (especially at 2 Mb/s ;-). - * - * I have also looked into disabling only our interrupt on the card - * (via HACR) instead of all interrupts in the processor (via cli), - * so that other driver are not impacted, and it look like it's - * possible, but it's very tricky to do right (full of races). As - * the gain would be mostly for SMP systems, it can wait... - * - * Debugging and options - * --------------------- - * You will find below a set of '#define" allowing a very fine control - * on the driver behaviour and the debug messages printed. - * The main options are : - * o SET_PSA_CRC, to have your card correctly recognised by - * an access point and the Point-to-Point diagnostic tool. - * o USE_PSA_CONFIG, to read configuration from the PSA (EEprom) - * (otherwise we always start afresh with some defaults) - * - * wavelan.o is too darned big - * --------------------------- - * That's true! There is a very simple way to reduce the driver - * object by 33%! Comment out the following line: - * #include <linux/wireless.h> - * Other compile options can also reduce the size of it... - * - * MAC address and hardware detection: - * ----------------------------------- - * The detection code for the WaveLAN checks that the first three - * octets of the MAC address fit the company code. This type of - * detection works well for AT&T cards (because the AT&T code is - * hardcoded in wavelan.h), but of course will fail for other - * manufacturers. - * - * If you are sure that your card is derived from the WaveLAN, - * here is the way to configure it: - * 1) Get your MAC address - * a) With your card utilities (wfreqsel, instconf, etc.) - * b) With the driver: - * o compile the kernel with DEBUG_CONFIG_INFO enabled - * o Boot and look the card messages - * 2) Set your MAC code (3 octets) in MAC_ADDRESSES[][3] (wavelan.h) - * 3) Compile and verify - * 4) Send me the MAC code. I will include it in the next version. - * - */ - -/* --------------------- WIRELESS EXTENSIONS --------------------- */ -/* - * This driver is the first to support "wireless extensions". - * This set of extensions provides a standard way to control the wireless - * characteristics of the hardware. Applications such as mobile IP may - * take advantage of it. - * - * It might be a good idea as well to fetch the wireless tools to - * configure the device and play a bit. - */ - -/* ---------------------------- FILES ---------------------------- */ -/* - * wavelan.c: actual code for the driver: C functions - * - * wavelan.p.h: private header: local types and variables for driver - * - * wavelan.h: description of the hardware interface and structs - * - * i82586.h: description of the Ethernet controller - */ - -/* --------------------------- HISTORY --------------------------- */ -/* - * This is based on information in the drivers' headers. It may not be - * accurate, and I guarantee only my best effort. - * - * The history of the WaveLAN drivers is as complicated as the history of - * the WaveLAN itself (NCR -> AT&T -> Lucent). - * - * It all started with Anders Klemets <klemets@paul.rutgers.edu> - * writing a WaveLAN ISA driver for the Mach microkernel. Girish - * Welling <welling@paul.rutgers.edu> had also worked on it. - * Keith Moore modified this for the PCMCIA hardware. - * - * Robert Morris <rtm@das.harvard.edu> ported these two drivers to BSDI - * and added specific PCMCIA support (there is currently no equivalent - * of the PCMCIA package under BSD). - * - * Jim Binkley <jrb@cs.pdx.edu> ported both BSDI drivers to FreeBSD. - * - * Bruce Janson <bruce@cs.usyd.edu.au> ported the BSDI ISA driver to Linux. - * - * Anthony D. Joseph <adj@lcs.mit.edu> started to modify Bruce's driver - * (with help of the BSDI PCMCIA driver) for PCMCIA. - * Yunzhou Li <yunzhou@strat.iol.unh.edu> finished this work. - * Joe Finney <joe@comp.lancs.ac.uk> patched the driver to start - * 2.00 cards correctly (2.4 GHz with frequency selection). - * David Hinds <dahinds@users.sourceforge.net> integrated the whole in his - * PCMCIA package (and bug corrections). - * - * I (Jean Tourrilhes - jt@hplb.hpl.hp.com) then started to make some - * patches to the PCMCIA driver. Later, I added code in the ISA driver - * for Wireless Extensions and full support of frequency selection - * cards. Then, I did the same to the PCMCIA driver, and did some - * reorganisation. Finally, I came back to the ISA driver to - * upgrade it at the same level as the PCMCIA one and reorganise - * the code. - * Loeke Brederveld <lbrederv@wavelan.com> from Lucent has given me - * much needed information on the WaveLAN hardware. - */ - -/* The original copyrights and literature mention others' names and - * credits. I don't know what their part in this development was. - */ - -/* By the way, for the copyright and legal stuff: - * almost everybody wrote code under the GNU or BSD license (or similar), - * and want their original copyright to remain somewhere in the - * code (for myself, I go with the GPL). - * Nobody wants to take responsibility for anything, except the fame. - */ - -/* --------------------------- CREDITS --------------------------- */ -/* - * This software was developed as a component of the - * Linux operating system. - * It is based on other device drivers and information - * either written or supplied by: - * Ajay Bakre <bakre@paul.rutgers.edu>, - * Donald Becker <becker@cesdis.gsfc.nasa.gov>, - * Loeke Brederveld <Loeke.Brederveld@Utrecht.NCR.com>, - * Brent Elphick <belphick@uwaterloo.ca>, - * Anders Klemets <klemets@it.kth.se>, - * Vladimir V. Kolpakov <w@stier.koenig.ru>, - * Marc Meertens <Marc.Meertens@Utrecht.NCR.com>, - * Pauline Middelink <middelin@polyware.iaf.nl>, - * Robert Morris <rtm@das.harvard.edu>, - * Jean Tourrilhes <jt@hpl.hp.com>, - * Girish Welling <welling@paul.rutgers.edu>, - * Clark Woodworth <clark@hiway1.exit109.com> - * Yongguang Zhang <ygz@isl.hrl.hac.com> - * - * Thanks go also to: - * James Ashton <jaa101@syseng.anu.edu.au>, - * Alan Cox <alan@lxorguk.ukuu.org.uk>, - * Allan Creighton <allanc@cs.usyd.edu.au>, - * Matthew Geier <matthew@cs.usyd.edu.au>, - * Remo di Giovanni <remo@cs.usyd.edu.au>, - * Eckhard Grah <grah@wrcs1.urz.uni-wuppertal.de>, - * Vipul Gupta <vgupta@cs.binghamton.edu>, - * Mark Hagan <mhagan@wtcpost.daytonoh.NCR.COM>, - * Tim Nicholson <tim@cs.usyd.edu.au>, - * Ian Parkin <ian@cs.usyd.edu.au>, - * John Rosenberg <johnr@cs.usyd.edu.au>, - * George Rossi <george@phm.gov.au>, - * Arthur Scott <arthur@cs.usyd.edu.au>, - * Stanislav Sinyagin <stas@isf.ru> - * and Peter Storey for their assistance and advice. - * - * Additional Credits: - * - * My development has been done initially under Debian 1.1 (Linux 2.0.x) - * and now under Debian 2.2, initially with an HP Vectra XP/60, and now - * an HP Vectra XP/90. - * - */ - -/* ------------------------- IMPROVEMENTS ------------------------- */ -/* - * I proudly present: - * - * Changes made in first pre-release: - * ---------------------------------- - * - reorganisation of the code, function name change - * - creation of private header (wavelan.p.h) - * - reorganised debug messages - * - more comments, history, etc. - * - mmc_init: configure the PSA if not done - * - mmc_init: correct default value of level threshold for PCMCIA - * - mmc_init: 2.00 detection better code for 2.00 initialization - * - better info at startup - * - IRQ setting (note: this setting is permanent) - * - watchdog: change strategy (and solve module removal problems) - * - add wireless extensions (ioctl and get_wireless_stats) - * get/set nwid/frequency on fly, info for /proc/net/wireless - * - more wireless extensions: SETSPY and GETSPY - * - make wireless extensions optional - * - private ioctl to set/get quality and level threshold, histogram - * - remove /proc/net/wavelan - * - suppress useless stuff from lp (net_local) - * - kernel 2.1 support (copy_to/from_user instead of memcpy_to/fromfs) - * - add message level (debug stuff in /var/adm/debug and errors not - * displayed at console and still in /var/adm/messages) - * - multi device support - * - start fixing the probe (init code) - * - more inlines - * - man page - * - many other minor details and cleanups - * - * Changes made in second pre-release: - * ----------------------------------- - * - clean up init code (probe and module init) - * - better multiple device support (module) - * - name assignment (module) - * - * Changes made in third pre-release: - * ---------------------------------- - * - be more conservative on timers - * - preliminary support for multicast (I still lack some details) - * - * Changes made in fourth pre-release: - * ----------------------------------- - * - multicast (revisited and finished) - * - avoid reset in set_multicast_list (a really big hack) - * if somebody could apply this code for other i82586 based drivers - * - share onboard memory 75% RU and 25% CU (instead of 50/50) - * - * Changes made for release in 2.1.15: - * ----------------------------------- - * - change the detection code for multi manufacturer code support - * - * Changes made for release in 2.1.17: - * ----------------------------------- - * - update to wireless extensions changes - * - silly bug in card initial configuration (psa_conf_status) - * - * Changes made for release in 2.1.27 & 2.0.30: - * -------------------------------------------- - * - small bug in debug code (probably not the last one...) - * - remove extern keyword for wavelan_probe() - * - level threshold is now a standard wireless extension (version 4 !) - * - modules parameters types (new module interface) - * - * Changes made for release in 2.1.36: - * ----------------------------------- - * - byte count stats (courtesy of David Hinds) - * - remove dev_tint stuff (courtesy of David Hinds) - * - encryption setting from Brent Elphick (thanks a lot!) - * - 'ioaddr' to 'u_long' for the Alpha (thanks to Stanislav Sinyagin) - * - * Other changes (not by me) : - * ------------------------- - * - Spelling and gramar "rectification". - * - * Changes made for release in 2.0.37 & 2.2.2 : - * ------------------------------------------ - * - Correct status in /proc/net/wireless - * - Set PSA CRC to make PtP diagnostic tool happy (Bob Gray) - * - Module init code don't fail if we found at least one card in - * the address list (Karlis Peisenieks) - * - Missing parenthesis (Christopher Peterson) - * - Correct i82586 configuration parameters - * - Encryption initialisation bug (Robert McCormack) - * - New mac addresses detected in the probe - * - Increase watchdog for busy environments - * - * Changes made for release in 2.0.38 & 2.2.7 : - * ------------------------------------------ - * - Correct the reception logic to better report errors and avoid - * sending bogus packet up the stack - * - Delay RU config to avoid corrupting first received packet - * - Change config completion code (to actually check something) - * - Avoid reading out of bound in skbuf to transmit - * - Rectify a lot of (useless) debugging code - * - Change the way to `#ifdef SET_PSA_CRC' - * - * Changes made for release in 2.2.11 & 2.3.13 : - * ------------------------------------------- - * - Change e-mail and web page addresses - * - Watchdog timer is now correctly expressed in HZ, not in jiffies - * - Add channel number to the list of frequencies in range - * - Add the (short) list of bit-rates in range - * - Developp a new sensitivity... (sens.value & sens.fixed) - * - * Changes made for release in 2.2.14 & 2.3.23 : - * ------------------------------------------- - * - Fix check for root permission (break instead of exit) - * - New nwid & encoding setting (Wireless Extension 9) - * - * Changes made for release in 2.3.49 : - * ---------------------------------- - * - Indentation reformating (Alan) - * - Update to new network API (softnet - 2.3.43) : - * o replace dev->tbusy (Alan) - * o replace dev->tstart (Alan) - * o remove dev->interrupt (Alan) - * o add SMP locking via spinlock in splxx (me) - * o add spinlock in interrupt handler (me) - * o use kernel watchdog instead of ours (me) - * o increase watchdog timeout (kernel is more sensitive) (me) - * o verify that all the changes make sense and work (me) - * - Fixup a potential gotcha when reconfiguring and thighten a bit - * the interactions with Tx queue. - * - * Changes made for release in 2.4.0 : - * --------------------------------- - * - Fix spinlock stupid bugs that I left in. The driver is now SMP - * compliant and doesn't lockup at startup. - * - * Changes made for release in 2.5.2 : - * --------------------------------- - * - Use new driver API for Wireless Extensions : - * o got rid of wavelan_ioctl() - * o use a bunch of iw_handler instead - * - * Changes made for release in 2.5.35 : - * ---------------------------------- - * - Set dev->trans_start to avoid filling the logs - * - Handle better spurious/bogus interrupt - * - Avoid deadlocks in mmc_out()/mmc_in() - * - * Wishes & dreams: - * ---------------- - * - roaming (see Pcmcia driver) - */ - -/***************************** INCLUDES *****************************/ - -#include <linux/module.h> - -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/types.h> -#include <linux/fcntl.h> -#include <linux/interrupt.h> -#include <linux/stat.h> -#include <linux/ptrace.h> -#include <linux/ioport.h> -#include <linux/in.h> -#include <linux/string.h> -#include <linux/delay.h> -#include <linux/bitops.h> -#include <asm/system.h> -#include <asm/io.h> -#include <asm/dma.h> -#include <asm/uaccess.h> -#include <linux/errno.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/slab.h> -#include <linux/timer.h> -#include <linux/init.h> - -#include <linux/wireless.h> /* Wireless extensions */ -#include <net/iw_handler.h> /* Wireless handlers */ - -/* WaveLAN declarations */ -#include "i82586.h" -#include "wavelan.h" - -/************************** DRIVER OPTIONS **************************/ -/* - * `#define' or `#undef' the following constant to change the behaviour - * of the driver... - */ -#undef SET_PSA_CRC /* Calculate and set the CRC on PSA (slower) */ -#define USE_PSA_CONFIG /* Use info from the PSA. */ -#undef EEPROM_IS_PROTECTED /* doesn't seem to be necessary */ -#define MULTICAST_AVOID /* Avoid extra multicast (I'm sceptical). */ -#undef SET_MAC_ADDRESS /* Experimental */ - -/* Warning: this stuff will slow down the driver. */ -#define WIRELESS_SPY /* Enable spying addresses. */ -#undef HISTOGRAM /* Enable histogram of signal level. */ - -/****************************** DEBUG ******************************/ - -#undef DEBUG_MODULE_TRACE /* module insertion/removal */ -#undef DEBUG_CALLBACK_TRACE /* calls made by Linux */ -#undef DEBUG_INTERRUPT_TRACE /* calls to handler */ -#undef DEBUG_INTERRUPT_INFO /* type of interrupt and so on */ -#define DEBUG_INTERRUPT_ERROR /* problems */ -#undef DEBUG_CONFIG_TRACE /* Trace the config functions. */ -#undef DEBUG_CONFIG_INFO /* what's going on */ -#define DEBUG_CONFIG_ERROR /* errors on configuration */ -#undef DEBUG_TX_TRACE /* transmission calls */ -#undef DEBUG_TX_INFO /* header of the transmitted packet */ -#undef DEBUG_TX_FAIL /* Normal failure conditions */ -#define DEBUG_TX_ERROR /* Unexpected conditions */ -#undef DEBUG_RX_TRACE /* transmission calls */ -#undef DEBUG_RX_INFO /* header of the received packet */ -#undef DEBUG_RX_FAIL /* Normal failure conditions */ -#define DEBUG_RX_ERROR /* Unexpected conditions */ - -#undef DEBUG_PACKET_DUMP /* Dump packet on the screen if defined to 32. */ -#undef DEBUG_IOCTL_TRACE /* misc. call by Linux */ -#undef DEBUG_IOCTL_INFO /* various debugging info */ -#define DEBUG_IOCTL_ERROR /* what's going wrong */ -#define DEBUG_BASIC_SHOW /* Show basic startup info. */ -#undef DEBUG_VERSION_SHOW /* Print version info. */ -#undef DEBUG_PSA_SHOW /* Dump PSA to screen. */ -#undef DEBUG_MMC_SHOW /* Dump mmc to screen. */ -#undef DEBUG_SHOW_UNUSED /* Show unused fields too. */ -#undef DEBUG_I82586_SHOW /* Show i82586 status. */ -#undef DEBUG_DEVICE_SHOW /* Show device parameters. */ - -/************************ CONSTANTS & MACROS ************************/ - -#ifdef DEBUG_VERSION_SHOW -static const char *version = "wavelan.c : v24 (SMP + wireless extensions) 11/12/01\n"; -#endif - -/* Watchdog temporisation */ -#define WATCHDOG_JIFFIES (512*HZ/100) - -/* ------------------------ PRIVATE IOCTL ------------------------ */ - -#define SIOCSIPQTHR SIOCIWFIRSTPRIV /* Set quality threshold */ -#define SIOCGIPQTHR SIOCIWFIRSTPRIV + 1 /* Get quality threshold */ - -#define SIOCSIPHISTO SIOCIWFIRSTPRIV + 2 /* Set histogram ranges */ -#define SIOCGIPHISTO SIOCIWFIRSTPRIV + 3 /* Get histogram values */ - -/****************************** TYPES ******************************/ - -/* Shortcuts */ -typedef struct iw_statistics iw_stats; -typedef struct iw_quality iw_qual; -typedef struct iw_freq iw_freq;typedef struct net_local net_local; -typedef struct timer_list timer_list; - -/* Basic types */ -typedef u_char mac_addr[WAVELAN_ADDR_SIZE]; /* Hardware address */ - -/* - * Static specific data for the interface. - * - * For each network interface, Linux keeps data in two structures: "device" - * keeps the generic data (same format for everybody) and "net_local" keeps - * additional specific data. - */ -struct net_local -{ - net_local * next; /* linked list of the devices */ - struct net_device * dev; /* reverse link */ - spinlock_t spinlock; /* Serialize access to the hardware (SMP) */ - int nresets; /* number of hardware resets */ - u_char reconfig_82586; /* We need to reconfigure the controller. */ - u_char promiscuous; /* promiscuous mode */ - int mc_count; /* number of multicast addresses */ - u_short hacr; /* current host interface state */ - - int tx_n_in_use; - u_short rx_head; - u_short rx_last; - u_short tx_first_free; - u_short tx_first_in_use; - - iw_stats wstats; /* Wireless-specific statistics */ - - struct iw_spy_data spy_data; - struct iw_public_data wireless_data; - -#ifdef HISTOGRAM - int his_number; /* number of intervals */ - u_char his_range[16]; /* boundaries of interval ]n-1; n] */ - u_long his_sum[16]; /* sum in interval */ -#endif /* HISTOGRAM */ -}; - -/**************************** PROTOTYPES ****************************/ - -/* ----------------------- MISC. SUBROUTINES ------------------------ */ -static u_char - wv_irq_to_psa(int); -static int - wv_psa_to_irq(u_char); -/* ------------------- HOST ADAPTER SUBROUTINES ------------------- */ -static inline u_short /* data */ - hasr_read(u_long); /* Read the host interface: base address */ -static inline void - hacr_write(u_long, /* Write to host interface: base address */ - u_short), /* data */ - hacr_write_slow(u_long, - u_short), - set_chan_attn(u_long, /* ioaddr */ - u_short), /* hacr */ - wv_hacr_reset(u_long), /* ioaddr */ - wv_16_off(u_long, /* ioaddr */ - u_short), /* hacr */ - wv_16_on(u_long, /* ioaddr */ - u_short), /* hacr */ - wv_ints_off(struct net_device *), - wv_ints_on(struct net_device *); -/* ----------------- MODEM MANAGEMENT SUBROUTINES ----------------- */ -static void - psa_read(u_long, /* Read the Parameter Storage Area. */ - u_short, /* hacr */ - int, /* offset in PSA */ - u_char *, /* buffer to fill */ - int), /* size to read */ - psa_write(u_long, /* Write to the PSA. */ - u_short, /* hacr */ - int, /* offset in PSA */ - u_char *, /* buffer in memory */ - int); /* length of buffer */ -static inline void - mmc_out(u_long, /* Write 1 byte to the Modem Manag Control. */ - u_short, - u_char), - mmc_write(u_long, /* Write n bytes to the MMC. */ - u_char, - u_char *, - int); -static inline u_char /* Read 1 byte from the MMC. */ - mmc_in(u_long, - u_short); -static inline void - mmc_read(u_long, /* Read n bytes from the MMC. */ - u_char, - u_char *, - int), - fee_wait(u_long, /* Wait for frequency EEPROM: base address */ - int, /* base delay to wait for */ - int); /* time to wait */ -static void - fee_read(u_long, /* Read the frequency EEPROM: base address */ - u_short, /* destination offset */ - u_short *, /* data buffer */ - int); /* number of registers */ -/* ---------------------- I82586 SUBROUTINES ----------------------- */ -static /*inline*/ void - obram_read(u_long, /* ioaddr */ - u_short, /* o */ - u_char *, /* b */ - int); /* n */ -static inline void - obram_write(u_long, /* ioaddr */ - u_short, /* o */ - u_char *, /* b */ - int); /* n */ -static void - wv_ack(struct net_device *); -static inline int - wv_synchronous_cmd(struct net_device *, - const char *), - wv_config_complete(struct net_device *, - u_long, - net_local *); -static int - wv_complete(struct net_device *, - u_long, - net_local *); -static inline void - wv_82586_reconfig(struct net_device *); -/* ------------------- DEBUG & INFO SUBROUTINES ------------------- */ -#ifdef DEBUG_I82586_SHOW -static void - wv_scb_show(unsigned short); -#endif -static inline void - wv_init_info(struct net_device *); /* display startup info */ -/* ------------------- IOCTL, STATS & RECONFIG ------------------- */ -static iw_stats * - wavelan_get_wireless_stats(struct net_device *); -static void - wavelan_set_multicast_list(struct net_device *); -/* ----------------------- PACKET RECEPTION ----------------------- */ -static inline void - wv_packet_read(struct net_device *, /* Read a packet from a frame. */ - u_short, - int), - wv_receive(struct net_device *); /* Read all packets waiting. */ -/* --------------------- PACKET TRANSMISSION --------------------- */ -static inline int - wv_packet_write(struct net_device *, /* Write a packet to the Tx buffer. */ - void *, - short); -static netdev_tx_t - wavelan_packet_xmit(struct sk_buff *, /* Send a packet. */ - struct net_device *); -/* -------------------- HARDWARE CONFIGURATION -------------------- */ -static inline int - wv_mmc_init(struct net_device *), /* Initialize the modem. */ - wv_ru_start(struct net_device *), /* Start the i82586 receiver unit. */ - wv_cu_start(struct net_device *), /* Start the i82586 command unit. */ - wv_82586_start(struct net_device *); /* Start the i82586. */ -static void - wv_82586_config(struct net_device *); /* Configure the i82586. */ -static inline void - wv_82586_stop(struct net_device *); -static int - wv_hw_reset(struct net_device *), /* Reset the WaveLAN hardware. */ - wv_check_ioaddr(u_long, /* ioaddr */ - u_char *); /* mac address (read) */ -/* ---------------------- INTERRUPT HANDLING ---------------------- */ -static irqreturn_t - wavelan_interrupt(int, /* interrupt handler */ - void *); -static void - wavelan_watchdog(struct net_device *); /* transmission watchdog */ -/* ------------------- CONFIGURATION CALLBACKS ------------------- */ -static int - wavelan_open(struct net_device *), /* Open the device. */ - wavelan_close(struct net_device *), /* Close the device. */ - wavelan_config(struct net_device *, unsigned short);/* Configure one device. */ -extern struct net_device *wavelan_probe(int unit); /* See Space.c. */ - -/**************************** VARIABLES ****************************/ - -/* - * This is the root of the linked list of WaveLAN drivers - * It is use to verify that we don't reuse the same base address - * for two different drivers and to clean up when removing the module. - */ -static net_local * wavelan_list = (net_local *) NULL; - -/* - * This table is used to translate the PSA value to IRQ number - * and vice versa. - */ -static u_char irqvals[] = -{ - 0, 0, 0, 0x01, - 0x02, 0x04, 0, 0x08, - 0, 0, 0x10, 0x20, - 0x40, 0, 0, 0x80, -}; - -/* - * Table of the available I/O addresses (base addresses) for WaveLAN - */ -static unsigned short iobase[] = -{ -#if 0 - /* Leave out 0x3C0 for now -- seems to clash with some video - * controllers. - * Leave out the others too -- we will always use 0x390 and leave - * 0x300 for the Ethernet device. - * Jean II: 0x3E0 is fine as well. - */ - 0x300, 0x390, 0x3E0, 0x3C0 -#endif /* 0 */ - 0x390, 0x3E0 -}; - -#ifdef MODULE -/* Parameters set by insmod */ -static int io[4]; -static int irq[4]; -static char *name[4]; -module_param_array(io, int, NULL, 0); -module_param_array(irq, int, NULL, 0); -module_param_array(name, charp, NULL, 0); - -MODULE_PARM_DESC(io, "WaveLAN I/O base address(es),required"); -MODULE_PARM_DESC(irq, "WaveLAN IRQ number(s)"); -MODULE_PARM_DESC(name, "WaveLAN interface neme(s)"); -#endif /* MODULE */ - -#endif /* WAVELAN_P_H */ diff --git a/drivers/net/wireless/wavelan_cs.c b/drivers/net/wireless/wavelan_cs.c deleted file mode 100644 index 431a20e..0000000 --- a/drivers/net/wireless/wavelan_cs.c +++ /dev/null @@ -1,4635 +0,0 @@ -/* - * Wavelan Pcmcia driver - * - * Jean II - HPLB '96 - * - * Reorganisation and extension of the driver. - * Original copyright follow. See wavelan_cs.p.h for details. - * - * This code is derived from Anthony D. Joseph's code and all the changes here - * are also under the original copyright below. - * - * This code supports version 2.00 of WaveLAN/PCMCIA cards (2.4GHz), and - * can work on Linux 2.0.36 with support of David Hinds' PCMCIA Card Services - * - * Joe Finney (joe@comp.lancs.ac.uk) at Lancaster University in UK added - * critical code in the routine to initialize the Modem Management Controller. - * - * Thanks to Alan Cox and Bruce Janson for their advice. - * - * -- Yunzhou Li (scip4166@nus.sg) - * -#ifdef WAVELAN_ROAMING - * Roaming support added 07/22/98 by Justin Seger (jseger@media.mit.edu) - * based on patch by Joe Finney from Lancaster University. -#endif - * - * Lucent (formerly AT&T GIS, formerly NCR) WaveLAN PCMCIA card: An - * Ethernet-like radio transceiver controlled by an Intel 82593 coprocessor. - * - * A non-shared memory PCMCIA ethernet driver for linux - * - * ISA version modified to support PCMCIA by Anthony Joseph (adj@lcs.mit.edu) - * - * - * Joseph O'Sullivan & John Langford (josullvn@cs.cmu.edu & jcl@cs.cmu.edu) - * - * Apr 2 '98 made changes to bring the i82593 control/int handling in line - * with offical specs... - * - **************************************************************************** - * Copyright 1995 - * Anthony D. Joseph - * Massachusetts Institute of Technology - * - * Permission to use, copy, modify, and distribute this program - * for any purpose and without fee is hereby granted, provided - * that this copyright and permission notice appear on all copies - * and supporting documentation, the name of M.I.T. not be used - * in advertising or publicity pertaining to distribution of the - * program without specific prior permission, and notice be given - * in supporting documentation that copying and distribution is - * by permission of M.I.T. M.I.T. makes no representations about - * the suitability of this software for any purpose. It is pro- - * vided "as is" without express or implied warranty. - **************************************************************************** - * - */ - -/* Do *NOT* add other headers here, you are guaranteed to be wrong - Jean II */ -#include "wavelan_cs.p.h" /* Private header */ - -#ifdef WAVELAN_ROAMING -static void wl_cell_expiry(unsigned long data); -static void wl_del_wavepoint(wavepoint_history *wavepoint, struct net_local *lp); -static void wv_nwid_filter(unsigned char mode, net_local *lp); -#endif /* WAVELAN_ROAMING */ - -/************************* MISC SUBROUTINES **************************/ -/* - * Subroutines which won't fit in one of the following category - * (wavelan modem or i82593) - */ - -/******************* MODEM MANAGEMENT SUBROUTINES *******************/ -/* - * Useful subroutines to manage the modem of the wavelan - */ - -/*------------------------------------------------------------------*/ -/* - * Read from card's Host Adaptor Status Register. - */ -static inline u_char -hasr_read(u_long base) -{ - return(inb(HASR(base))); -} /* hasr_read */ - -/*------------------------------------------------------------------*/ -/* - * Write to card's Host Adapter Command Register. - */ -static inline void -hacr_write(u_long base, - u_char hacr) -{ - outb(hacr, HACR(base)); -} /* hacr_write */ - -/*------------------------------------------------------------------*/ -/* - * Write to card's Host Adapter Command Register. Include a delay for - * those times when it is needed. - */ -static void -hacr_write_slow(u_long base, - u_char hacr) -{ - hacr_write(base, hacr); - /* delay might only be needed sometimes */ - mdelay(1); -} /* hacr_write_slow */ - -/*------------------------------------------------------------------*/ -/* - * Read the Parameter Storage Area from the WaveLAN card's memory - */ -static void -psa_read(struct net_device * dev, - int o, /* offset in PSA */ - u_char * b, /* buffer to fill */ - int n) /* size to read */ -{ - net_local *lp = netdev_priv(dev); - u_char __iomem *ptr = lp->mem + PSA_ADDR + (o << 1); - - while(n-- > 0) - { - *b++ = readb(ptr); - /* Due to a lack of address decode pins, the WaveLAN PCMCIA card - * only supports reading even memory addresses. That means the - * increment here MUST be two. - * Because of that, we can't use memcpy_fromio()... - */ - ptr += 2; - } -} /* psa_read */ - -/*------------------------------------------------------------------*/ -/* - * Write the Parameter Storage Area to the WaveLAN card's memory - */ -static void -psa_write(struct net_device * dev, - int o, /* Offset in psa */ - u_char * b, /* Buffer in memory */ - int n) /* Length of buffer */ -{ - net_local *lp = netdev_priv(dev); - u_char __iomem *ptr = lp->mem + PSA_ADDR + (o << 1); - int count = 0; - unsigned int base = dev->base_addr; - /* As there seem to have no flag PSA_BUSY as in the ISA model, we are - * oblige to verify this address to know when the PSA is ready... */ - volatile u_char __iomem *verify = lp->mem + PSA_ADDR + - (psaoff(0, psa_comp_number) << 1); - - /* Authorize writing to PSA */ - hacr_write(base, HACR_PWR_STAT | HACR_ROM_WEN); - - while(n-- > 0) - { - /* write to PSA */ - writeb(*b++, ptr); - ptr += 2; - - /* I don't have the spec, so I don't know what the correct - * sequence to write is. This hack seem to work for me... */ - count = 0; - while((readb(verify) != PSA_COMP_PCMCIA_915) && (count++ < 100)) - mdelay(1); - } - - /* Put the host interface back in standard state */ - hacr_write(base, HACR_DEFAULT); -} /* psa_write */ - -#ifdef SET_PSA_CRC -/*------------------------------------------------------------------*/ -/* - * Calculate the PSA CRC - * Thanks to Valster, Nico <NVALSTER@wcnd.nl.lucent.com> for the code - * NOTE: By specifying a length including the CRC position the - * returned value should be zero. (i.e. a correct checksum in the PSA) - * - * The Windows drivers don't use the CRC, but the AP and the PtP tool - * depend on it. - */ -static u_short -psa_crc(unsigned char * psa, /* The PSA */ - int size) /* Number of short for CRC */ -{ - int byte_cnt; /* Loop on the PSA */ - u_short crc_bytes = 0; /* Data in the PSA */ - int bit_cnt; /* Loop on the bits of the short */ - - for(byte_cnt = 0; byte_cnt < size; byte_cnt++ ) - { - crc_bytes ^= psa[byte_cnt]; /* Its an xor */ - - for(bit_cnt = 1; bit_cnt < 9; bit_cnt++ ) - { - if(crc_bytes & 0x0001) - crc_bytes = (crc_bytes >> 1) ^ 0xA001; - else - crc_bytes >>= 1 ; - } - } - - return crc_bytes; -} /* psa_crc */ -#endif /* SET_PSA_CRC */ - -/*------------------------------------------------------------------*/ -/* - * update the checksum field in the Wavelan's PSA - */ -static void -update_psa_checksum(struct net_device * dev) -{ -#ifdef SET_PSA_CRC - psa_t psa; - u_short crc; - - /* read the parameter storage area */ - psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa)); - - /* update the checksum */ - crc = psa_crc((unsigned char *) &psa, - sizeof(psa) - sizeof(psa.psa_crc[0]) - sizeof(psa.psa_crc[1]) - - sizeof(psa.psa_crc_status)); - - psa.psa_crc[0] = crc & 0xFF; - psa.psa_crc[1] = (crc & 0xFF00) >> 8; - - /* Write it ! */ - psa_write(dev, (char *)&psa.psa_crc - (char *)&psa, - (unsigned char *)&psa.psa_crc, 2); - -#ifdef DEBUG_IOCTL_INFO - printk (KERN_DEBUG "%s: update_psa_checksum(): crc = 0x%02x%02x\n", - dev->name, psa.psa_crc[0], psa.psa_crc[1]); - - /* Check again (luxury !) */ - crc = psa_crc((unsigned char *) &psa, - sizeof(psa) - sizeof(psa.psa_crc_status)); - - if(crc != 0) - printk(KERN_WARNING "%s: update_psa_checksum(): CRC does not agree with PSA data (even after recalculating)\n", dev->name); -#endif /* DEBUG_IOCTL_INFO */ -#endif /* SET_PSA_CRC */ -} /* update_psa_checksum */ - -/*------------------------------------------------------------------*/ -/* - * Write 1 byte to the MMC. - */ -static void -mmc_out(u_long base, - u_short o, - u_char d) -{ - int count = 0; - - /* Wait for MMC to go idle */ - while((count++ < 100) && (inb(HASR(base)) & HASR_MMI_BUSY)) - udelay(10); - - outb((u_char)((o << 1) | MMR_MMI_WR), MMR(base)); - outb(d, MMD(base)); -} - -/*------------------------------------------------------------------*/ -/* - * Routine to write bytes to the Modem Management Controller. - * We start by the end because it is the way it should be ! - */ -static void -mmc_write(u_long base, - u_char o, - u_char * b, - int n) -{ - o += n; - b += n; - - while(n-- > 0 ) - mmc_out(base, --o, *(--b)); -} /* mmc_write */ - -/*------------------------------------------------------------------*/ -/* - * Read 1 byte from the MMC. - * Optimised version for 1 byte, avoid using memory... - */ -static u_char -mmc_in(u_long base, - u_short o) -{ - int count = 0; - - while((count++ < 100) && (inb(HASR(base)) & HASR_MMI_BUSY)) - udelay(10); - outb(o << 1, MMR(base)); /* Set the read address */ - - outb(0, MMD(base)); /* Required dummy write */ - - while((count++ < 100) && (inb(HASR(base)) & HASR_MMI_BUSY)) - udelay(10); - return (u_char) (inb(MMD(base))); /* Now do the actual read */ -} - -/*------------------------------------------------------------------*/ -/* - * Routine to read bytes from the Modem Management Controller. - * The implementation is complicated by a lack of address lines, - * which prevents decoding of the low-order bit. - * (code has just been moved in the above function) - * We start by the end because it is the way it should be ! - */ -static void -mmc_read(u_long base, - u_char o, - u_char * b, - int n) -{ - o += n; - b += n; - - while(n-- > 0) - *(--b) = mmc_in(base, --o); -} /* mmc_read */ - -/*------------------------------------------------------------------*/ -/* - * Get the type of encryption available... - */ -static inline int -mmc_encr(u_long base) /* i/o port of the card */ -{ - int temp; - - temp = mmc_in(base, mmroff(0, mmr_des_avail)); - if((temp != MMR_DES_AVAIL_DES) && (temp != MMR_DES_AVAIL_AES)) - return 0; - else - return temp; -} - -/*------------------------------------------------------------------*/ -/* - * Wait for the frequency EEprom to complete a command... - */ -static void -fee_wait(u_long base, /* i/o port of the card */ - int delay, /* Base delay to wait for */ - int number) /* Number of time to wait */ -{ - int count = 0; /* Wait only a limited time */ - - while((count++ < number) && - (mmc_in(base, mmroff(0, mmr_fee_status)) & MMR_FEE_STATUS_BUSY)) - udelay(delay); -} - -/*------------------------------------------------------------------*/ -/* - * Read bytes from the Frequency EEprom (frequency select cards). - */ -static void -fee_read(u_long base, /* i/o port of the card */ - u_short o, /* destination offset */ - u_short * b, /* data buffer */ - int n) /* number of registers */ -{ - b += n; /* Position at the end of the area */ - - /* Write the address */ - mmc_out(base, mmwoff(0, mmw_fee_addr), o + n - 1); - - /* Loop on all buffer */ - while(n-- > 0) - { - /* Write the read command */ - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_READ); - - /* Wait until EEprom is ready (should be quick !) */ - fee_wait(base, 10, 100); - - /* Read the value */ - *--b = ((mmc_in(base, mmroff(0, mmr_fee_data_h)) << 8) | - mmc_in(base, mmroff(0, mmr_fee_data_l))); - } -} - - -/*------------------------------------------------------------------*/ -/* - * Write bytes from the Frequency EEprom (frequency select cards). - * This is a bit complicated, because the frequency eeprom has to - * be unprotected and the write enabled. - * Jean II - */ -static void -fee_write(u_long base, /* i/o port of the card */ - u_short o, /* destination offset */ - u_short * b, /* data buffer */ - int n) /* number of registers */ -{ - b += n; /* Position at the end of the area */ - -#ifdef EEPROM_IS_PROTECTED /* disabled */ -#ifdef DOESNT_SEEM_TO_WORK /* disabled */ - /* Ask to read the protected register */ - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRREAD); - - fee_wait(base, 10, 100); - - /* Read the protected register */ - printk("Protected 2 : %02X-%02X\n", - mmc_in(base, mmroff(0, mmr_fee_data_h)), - mmc_in(base, mmroff(0, mmr_fee_data_l))); -#endif /* DOESNT_SEEM_TO_WORK */ - - /* Enable protected register */ - mmc_out(base, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_EN); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PREN); - - fee_wait(base, 10, 100); - - /* Unprotect area */ - mmc_out(base, mmwoff(0, mmw_fee_addr), o + n); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRWRITE); -#ifdef DOESNT_SEEM_TO_WORK /* disabled */ - /* Or use : */ - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRCLEAR); -#endif /* DOESNT_SEEM_TO_WORK */ - - fee_wait(base, 10, 100); -#endif /* EEPROM_IS_PROTECTED */ - - /* Write enable */ - mmc_out(base, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_EN); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WREN); - - fee_wait(base, 10, 100); - - /* Write the EEprom address */ - mmc_out(base, mmwoff(0, mmw_fee_addr), o + n - 1); - - /* Loop on all buffer */ - while(n-- > 0) - { - /* Write the value */ - mmc_out(base, mmwoff(0, mmw_fee_data_h), (*--b) >> 8); - mmc_out(base, mmwoff(0, mmw_fee_data_l), *b & 0xFF); - - /* Write the write command */ - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WRITE); - - /* Wavelan doc says : wait at least 10 ms for EEBUSY = 0 */ - mdelay(10); - fee_wait(base, 10, 100); - } - - /* Write disable */ - mmc_out(base, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_DS); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WDS); - - fee_wait(base, 10, 100); - -#ifdef EEPROM_IS_PROTECTED /* disabled */ - /* Reprotect EEprom */ - mmc_out(base, mmwoff(0, mmw_fee_addr), 0x00); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRWRITE); - - fee_wait(base, 10, 100); -#endif /* EEPROM_IS_PROTECTED */ -} - -/******************* WaveLAN Roaming routines... ********************/ - -#ifdef WAVELAN_ROAMING /* Conditional compile, see wavelan_cs.h */ - -static unsigned char WAVELAN_BEACON_ADDRESS[] = {0x09,0x00,0x0e,0x20,0x03,0x00}; - -static void wv_roam_init(struct net_device *dev) -{ - net_local *lp= netdev_priv(dev); - - /* Do not remove this unless you have a good reason */ - printk(KERN_NOTICE "%s: Warning, you have enabled roaming on" - " device %s !\n", dev->name, dev->name); - printk(KERN_NOTICE "Roaming is currently an experimental unsupported feature" - " of the Wavelan driver.\n"); - printk(KERN_NOTICE "It may work, but may also make the driver behave in" - " erratic ways or crash.\n"); - - lp->wavepoint_table.head=NULL; /* Initialise WavePoint table */ - lp->wavepoint_table.num_wavepoints=0; - lp->wavepoint_table.locked=0; - lp->curr_point=NULL; /* No default WavePoint */ - lp->cell_search=0; - - lp->cell_timer.data=(long)lp; /* Start cell expiry timer */ - lp->cell_timer.function=wl_cell_expiry; - lp->cell_timer.expires=jiffies+CELL_TIMEOUT; - add_timer(&lp->cell_timer); - - wv_nwid_filter(NWID_PROMISC,lp) ; /* Enter NWID promiscuous mode */ - /* to build up a good WavePoint */ - /* table... */ - printk(KERN_DEBUG "WaveLAN: Roaming enabled on device %s\n",dev->name); -} - -static void wv_roam_cleanup(struct net_device *dev) -{ - wavepoint_history *ptr,*old_ptr; - net_local *lp= netdev_priv(dev); - - printk(KERN_DEBUG "WaveLAN: Roaming Disabled on device %s\n",dev->name); - - /* Fixme : maybe we should check that the timer exist before deleting it */ - del_timer(&lp->cell_timer); /* Remove cell expiry timer */ - ptr=lp->wavepoint_table.head; /* Clear device's WavePoint table */ - while(ptr!=NULL) - { - old_ptr=ptr; - ptr=ptr->next; - wl_del_wavepoint(old_ptr,lp); - } -} - -/* Enable/Disable NWID promiscuous mode on a given device */ -static void wv_nwid_filter(unsigned char mode, net_local *lp) -{ - mm_t m; - unsigned long flags; - -#ifdef WAVELAN_ROAMING_DEBUG - printk(KERN_DEBUG "WaveLAN: NWID promisc %s, device %s\n",(mode==NWID_PROMISC) ? "on" : "off", lp->dev->name); -#endif - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&lp->spinlock, flags); - - m.w.mmw_loopt_sel = (mode==NWID_PROMISC) ? MMW_LOOPT_SEL_DIS_NWID : 0x00; - mmc_write(lp->dev->base_addr, (char *)&m.w.mmw_loopt_sel - (char *)&m, (unsigned char *)&m.w.mmw_loopt_sel, 1); - - if(mode==NWID_PROMISC) - lp->cell_search=1; - else - lp->cell_search=0; - - /* ReEnable interrupts & restore flags */ - spin_unlock_irqrestore(&lp->spinlock, flags); -} - -/* Find a record in the WavePoint table matching a given NWID */ -static wavepoint_history *wl_roam_check(unsigned short nwid, net_local *lp) -{ - wavepoint_history *ptr=lp->wavepoint_table.head; - - while(ptr!=NULL){ - if(ptr->nwid==nwid) - return ptr; - ptr=ptr->next; - } - return NULL; -} - -/* Create a new wavepoint table entry */ -static wavepoint_history *wl_new_wavepoint(unsigned short nwid, unsigned char seq, net_local* lp) -{ - wavepoint_history *new_wavepoint; - -#ifdef WAVELAN_ROAMING_DEBUG - printk(KERN_DEBUG "WaveLAN: New Wavepoint, NWID:%.4X\n",nwid); -#endif - - if(lp->wavepoint_table.num_wavepoints==MAX_WAVEPOINTS) - return NULL; - - new_wavepoint = kmalloc(sizeof(wavepoint_history),GFP_ATOMIC); - if(new_wavepoint==NULL) - return NULL; - - new_wavepoint->nwid=nwid; /* New WavePoints NWID */ - new_wavepoint->average_fast=0; /* Running Averages..*/ - new_wavepoint->average_slow=0; - new_wavepoint->qualptr=0; /* Start of ringbuffer */ - new_wavepoint->last_seq=seq-1; /* Last sequence no.seen */ - memset(new_wavepoint->sigqual,0,WAVEPOINT_HISTORY);/* Empty ringbuffer */ - - new_wavepoint->next=lp->wavepoint_table.head;/* Add to wavepoint table */ - new_wavepoint->prev=NULL; - - if(lp->wavepoint_table.head!=NULL) - lp->wavepoint_table.head->prev=new_wavepoint; - - lp->wavepoint_table.head=new_wavepoint; - - lp->wavepoint_table.num_wavepoints++; /* no. of visible wavepoints */ - - return new_wavepoint; -} - -/* Remove a wavepoint entry from WavePoint table */ -static void wl_del_wavepoint(wavepoint_history *wavepoint, struct net_local *lp) -{ - if(wavepoint==NULL) - return; - - if(lp->curr_point==wavepoint) - lp->curr_point=NULL; - - if(wavepoint->prev!=NULL) - wavepoint->prev->next=wavepoint->next; - - if(wavepoint->next!=NULL) - wavepoint->next->prev=wavepoint->prev; - - if(lp->wavepoint_table.head==wavepoint) - lp->wavepoint_table.head=wavepoint->next; - - lp->wavepoint_table.num_wavepoints--; - kfree(wavepoint); -} - -/* Timer callback function - checks WavePoint table for stale entries */ -static void wl_cell_expiry(unsigned long data) -{ - net_local *lp=(net_local *)data; - wavepoint_history *wavepoint=lp->wavepoint_table.head,*old_point; - -#if WAVELAN_ROAMING_DEBUG > 1 - printk(KERN_DEBUG "WaveLAN: Wavepoint timeout, dev %s\n",lp->dev->name); -#endif - - if(lp->wavepoint_table.locked) - { -#if WAVELAN_ROAMING_DEBUG > 1 - printk(KERN_DEBUG "WaveLAN: Wavepoint table locked...\n"); -#endif - - lp->cell_timer.expires=jiffies+1; /* If table in use, come back later */ - add_timer(&lp->cell_timer); - return; - } - - while(wavepoint!=NULL) - { - if(time_after(jiffies, wavepoint->last_seen + CELL_TIMEOUT)) - { -#ifdef WAVELAN_ROAMING_DEBUG - printk(KERN_DEBUG "WaveLAN: Bye bye %.4X\n",wavepoint->nwid); -#endif - - old_point=wavepoint; - wavepoint=wavepoint->next; - wl_del_wavepoint(old_point,lp); - } - else - wavepoint=wavepoint->next; - } - lp->cell_timer.expires=jiffies+CELL_TIMEOUT; - add_timer(&lp->cell_timer); -} - -/* Update SNR history of a wavepoint */ -static void wl_update_history(wavepoint_history *wavepoint, unsigned char sigqual, unsigned char seq) -{ - int i=0,num_missed=0,ptr=0; - int average_fast=0,average_slow=0; - - num_missed=(seq-wavepoint->last_seq)%WAVEPOINT_HISTORY;/* Have we missed - any beacons? */ - if(num_missed) - for(i=0;i<num_missed;i++) - { - wavepoint->sigqual[wavepoint->qualptr++]=0; /* If so, enter them as 0's */ - wavepoint->qualptr %=WAVEPOINT_HISTORY; /* in the ringbuffer. */ - } - wavepoint->last_seen=jiffies; /* Add beacon to history */ - wavepoint->last_seq=seq; - wavepoint->sigqual[wavepoint->qualptr++]=sigqual; - wavepoint->qualptr %=WAVEPOINT_HISTORY; - ptr=(wavepoint->qualptr-WAVEPOINT_FAST_HISTORY+WAVEPOINT_HISTORY)%WAVEPOINT_HISTORY; - - for(i=0;i<WAVEPOINT_FAST_HISTORY;i++) /* Update running averages */ - { - average_fast+=wavepoint->sigqual[ptr++]; - ptr %=WAVEPOINT_HISTORY; - } - - average_slow=average_fast; - for(i=WAVEPOINT_FAST_HISTORY;i<WAVEPOINT_HISTORY;i++) - { - average_slow+=wavepoint->sigqual[ptr++]; - ptr %=WAVEPOINT_HISTORY; - } - - wavepoint->average_fast=average_fast/WAVEPOINT_FAST_HISTORY; - wavepoint->average_slow=average_slow/WAVEPOINT_HISTORY; -} - -/* Perform a handover to a new WavePoint */ -static void wv_roam_handover(wavepoint_history *wavepoint, net_local *lp) -{ - unsigned int base = lp->dev->base_addr; - mm_t m; - unsigned long flags; - - if(wavepoint==lp->curr_point) /* Sanity check... */ - { - wv_nwid_filter(!NWID_PROMISC,lp); - return; - } - -#ifdef WAVELAN_ROAMING_DEBUG - printk(KERN_DEBUG "WaveLAN: Doing handover to %.4X, dev %s\n",wavepoint->nwid,lp->dev->name); -#endif - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&lp->spinlock, flags); - - m.w.mmw_netw_id_l = wavepoint->nwid & 0xFF; - m.w.mmw_netw_id_h = (wavepoint->nwid & 0xFF00) >> 8; - - mmc_write(base, (char *)&m.w.mmw_netw_id_l - (char *)&m, (unsigned char *)&m.w.mmw_netw_id_l, 2); - - /* ReEnable interrupts & restore flags */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - wv_nwid_filter(!NWID_PROMISC,lp); - lp->curr_point=wavepoint; -} - -/* Called when a WavePoint beacon is received */ -static void wl_roam_gather(struct net_device * dev, - u_char * hdr, /* Beacon header */ - u_char * stats) /* SNR, Signal quality - of packet */ -{ - wavepoint_beacon *beacon= (wavepoint_beacon *)hdr; /* Rcvd. Beacon */ - unsigned short nwid=ntohs(beacon->nwid); - unsigned short sigqual=stats[2] & MMR_SGNL_QUAL; /* SNR of beacon */ - wavepoint_history *wavepoint=NULL; /* WavePoint table entry */ - net_local *lp = netdev_priv(dev); /* Device info */ - -#ifdef I_NEED_THIS_FEATURE - /* Some people don't need this, some other may need it */ - nwid=nwid^ntohs(beacon->domain_id); -#endif - -#if WAVELAN_ROAMING_DEBUG > 1 - printk(KERN_DEBUG "WaveLAN: beacon, dev %s:\n",dev->name); - printk(KERN_DEBUG "Domain: %.4X NWID: %.4X SigQual=%d\n",ntohs(beacon->domain_id),nwid,sigqual); -#endif - - lp->wavepoint_table.locked=1; /* <Mutex> */ - - wavepoint=wl_roam_check(nwid,lp); /* Find WavePoint table entry */ - if(wavepoint==NULL) /* If no entry, Create a new one... */ - { - wavepoint=wl_new_wavepoint(nwid,beacon->seq,lp); - if(wavepoint==NULL) - goto out; - } - if(lp->curr_point==NULL) /* If this is the only WavePoint, */ - wv_roam_handover(wavepoint, lp); /* Jump on it! */ - - wl_update_history(wavepoint, sigqual, beacon->seq); /* Update SNR history - stats. */ - - if(lp->curr_point->average_slow < SEARCH_THRESH_LOW) /* If our current */ - if(!lp->cell_search) /* WavePoint is getting faint, */ - wv_nwid_filter(NWID_PROMISC,lp); /* start looking for a new one */ - - if(wavepoint->average_slow > - lp->curr_point->average_slow + WAVELAN_ROAMING_DELTA) - wv_roam_handover(wavepoint, lp); /* Handover to a better WavePoint */ - - if(lp->curr_point->average_slow > SEARCH_THRESH_HIGH) /* If our SNR is */ - if(lp->cell_search) /* getting better, drop out of cell search mode */ - wv_nwid_filter(!NWID_PROMISC,lp); - -out: - lp->wavepoint_table.locked=0; /* </MUTEX> :-) */ -} - -/* Test this MAC frame a WavePoint beacon */ -static inline int WAVELAN_BEACON(unsigned char *data) -{ - wavepoint_beacon *beacon= (wavepoint_beacon *)data; - static const wavepoint_beacon beacon_template={0xaa,0xaa,0x03,0x08,0x00,0x0e,0x20,0x03,0x00}; - - if(memcmp(beacon,&beacon_template,9)==0) - return 1; - else - return 0; -} -#endif /* WAVELAN_ROAMING */ - -/************************ I82593 SUBROUTINES *************************/ -/* - * Useful subroutines to manage the Ethernet controller - */ - -/*------------------------------------------------------------------*/ -/* - * Routine to synchronously send a command to the i82593 chip. - * Should be called with interrupts disabled. - * (called by wv_packet_write(), wv_ru_stop(), wv_ru_start(), - * wv_82593_config() & wv_diag()) - */ -static int -wv_82593_cmd(struct net_device * dev, - char * str, - int cmd, - int result) -{ - unsigned int base = dev->base_addr; - int status; - int wait_completed; - long spin; - - /* Spin until the chip finishes executing its current command (if any) */ - spin = 1000; - do - { - /* Time calibration of the loop */ - udelay(10); - - /* Read the interrupt register */ - outb(OP0_NOP | CR0_STATUS_3, LCCR(base)); - status = inb(LCSR(base)); - } - while(((status & SR3_EXEC_STATE_MASK) != SR3_EXEC_IDLE) && (spin-- > 0)); - - /* If the interrupt hasn't been posted */ - if (spin < 0) { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "wv_82593_cmd: %s timeout (previous command), status 0x%02x\n", - str, status); -#endif - return(FALSE); - } - - /* Issue the command to the controller */ - outb(cmd, LCCR(base)); - - /* If we don't have to check the result of the command - * Note : this mean that the irq handler will deal with that */ - if(result == SR0_NO_RESULT) - return(TRUE); - - /* We are waiting for command completion */ - wait_completed = TRUE; - - /* Busy wait while the LAN controller executes the command. */ - spin = 1000; - do - { - /* Time calibration of the loop */ - udelay(10); - - /* Read the interrupt register */ - outb(CR0_STATUS_0 | OP0_NOP, LCCR(base)); - status = inb(LCSR(base)); - - /* Check if there was an interrupt posted */ - if((status & SR0_INTERRUPT)) - { - /* Acknowledge the interrupt */ - outb(CR0_INT_ACK | OP0_NOP, LCCR(base)); - - /* Check if interrupt is a command completion */ - if(((status & SR0_BOTH_RX_TX) != SR0_BOTH_RX_TX) && - ((status & SR0_BOTH_RX_TX) != 0x0) && - !(status & SR0_RECEPTION)) - { - /* Signal command completion */ - wait_completed = FALSE; - } - else - { - /* Note : Rx interrupts will be handled later, because we can - * handle multiple Rx packets at once */ -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_INFO "wv_82593_cmd: not our interrupt\n"); -#endif - } - } - } - while(wait_completed && (spin-- > 0)); - - /* If the interrupt hasn't be posted */ - if(wait_completed) - { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "wv_82593_cmd: %s timeout, status 0x%02x\n", - str, status); -#endif - return(FALSE); - } - - /* Check the return code returned by the card (see above) against - * the expected return code provided by the caller */ - if((status & SR0_EVENT_MASK) != result) - { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "wv_82593_cmd: %s failed, status = 0x%x\n", - str, status); -#endif - return(FALSE); - } - - return(TRUE); -} /* wv_82593_cmd */ - -/*------------------------------------------------------------------*/ -/* - * This routine does a 593 op-code number 7, and obtains the diagnose - * status for the WaveLAN. - */ -static inline int -wv_diag(struct net_device * dev) -{ - return(wv_82593_cmd(dev, "wv_diag(): diagnose", - OP0_DIAGNOSE, SR0_DIAGNOSE_PASSED)); -} /* wv_diag */ - -/*------------------------------------------------------------------*/ -/* - * Routine to read len bytes from the i82593's ring buffer, starting at - * chip address addr. The results read from the chip are stored in buf. - * The return value is the address to use for next the call. - */ -static int -read_ringbuf(struct net_device * dev, - int addr, - char * buf, - int len) -{ - unsigned int base = dev->base_addr; - int ring_ptr = addr; - int chunk_len; - char * buf_ptr = buf; - - /* Get all the buffer */ - while(len > 0) - { - /* Position the Program I/O Register at the ring buffer pointer */ - outb(ring_ptr & 0xff, PIORL(base)); - outb(((ring_ptr >> 8) & PIORH_MASK), PIORH(base)); - - /* First, determine how much we can read without wrapping around the - ring buffer */ - if((addr + len) < (RX_BASE + RX_SIZE)) - chunk_len = len; - else - chunk_len = RX_BASE + RX_SIZE - addr; - insb(PIOP(base), buf_ptr, chunk_len); - buf_ptr += chunk_len; - len -= chunk_len; - ring_ptr = (ring_ptr - RX_BASE + chunk_len) % RX_SIZE + RX_BASE; - } - return(ring_ptr); -} /* read_ringbuf */ - -/*------------------------------------------------------------------*/ -/* - * Reconfigure the i82593, or at least ask for it... - * Because wv_82593_config use the transmission buffer, we must do it - * when we are sure that there is no transmission, so we do it now - * or in wavelan_packet_xmit() (I can't find any better place, - * wavelan_interrupt is not an option...), so you may experience - * some delay sometime... - */ -static void -wv_82593_reconfig(struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - struct pcmcia_device * link = lp->link; - unsigned long flags; - - /* Arm the flag, will be cleard in wv_82593_config() */ - lp->reconfig_82593 = TRUE; - - /* Check if we can do it now ! */ - if((link->open) && (netif_running(dev)) && !(netif_queue_stopped(dev))) - { - spin_lock_irqsave(&lp->spinlock, flags); /* Disable interrupts */ - wv_82593_config(dev); - spin_unlock_irqrestore(&lp->spinlock, flags); /* Re-enable interrupts */ - } - else - { -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG - "%s: wv_82593_reconfig(): delayed (state = %lX, link = %d)\n", - dev->name, dev->state, link->open); -#endif - } -} - -/********************* DEBUG & INFO SUBROUTINES *********************/ -/* - * This routines are used in the code to show debug informations. - * Most of the time, it dump the content of hardware structures... - */ - -#ifdef DEBUG_PSA_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted contents of the Parameter Storage Area. - */ -static void -wv_psa_show(psa_t * p) -{ - printk(KERN_DEBUG "##### wavelan psa contents: #####\n"); - printk(KERN_DEBUG "psa_io_base_addr_1: 0x%02X %02X %02X %02X\n", - p->psa_io_base_addr_1, - p->psa_io_base_addr_2, - p->psa_io_base_addr_3, - p->psa_io_base_addr_4); - printk(KERN_DEBUG "psa_rem_boot_addr_1: 0x%02X %02X %02X\n", - p->psa_rem_boot_addr_1, - p->psa_rem_boot_addr_2, - p->psa_rem_boot_addr_3); - printk(KERN_DEBUG "psa_holi_params: 0x%02x, ", p->psa_holi_params); - printk("psa_int_req_no: %d\n", p->psa_int_req_no); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "psa_unused0[]: %pM\n", p->psa_unused0); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "psa_univ_mac_addr[]: %pM\n", p->psa_univ_mac_addr); - printk(KERN_DEBUG "psa_local_mac_addr[]: %pM\n", p->psa_local_mac_addr); - printk(KERN_DEBUG "psa_univ_local_sel: %d, ", p->psa_univ_local_sel); - printk("psa_comp_number: %d, ", p->psa_comp_number); - printk("psa_thr_pre_set: 0x%02x\n", p->psa_thr_pre_set); - printk(KERN_DEBUG "psa_feature_select/decay_prm: 0x%02x, ", - p->psa_feature_select); - printk("psa_subband/decay_update_prm: %d\n", p->psa_subband); - printk(KERN_DEBUG "psa_quality_thr: 0x%02x, ", p->psa_quality_thr); - printk("psa_mod_delay: 0x%02x\n", p->psa_mod_delay); - printk(KERN_DEBUG "psa_nwid: 0x%02x%02x, ", p->psa_nwid[0], p->psa_nwid[1]); - printk("psa_nwid_select: %d\n", p->psa_nwid_select); - printk(KERN_DEBUG "psa_encryption_select: %d, ", p->psa_encryption_select); - printk("psa_encryption_key[]: %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n", - p->psa_encryption_key[0], - p->psa_encryption_key[1], - p->psa_encryption_key[2], - p->psa_encryption_key[3], - p->psa_encryption_key[4], - p->psa_encryption_key[5], - p->psa_encryption_key[6], - p->psa_encryption_key[7]); - printk(KERN_DEBUG "psa_databus_width: %d\n", p->psa_databus_width); - printk(KERN_DEBUG "psa_call_code/auto_squelch: 0x%02x, ", - p->psa_call_code[0]); - printk("psa_call_code[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n", - p->psa_call_code[0], - p->psa_call_code[1], - p->psa_call_code[2], - p->psa_call_code[3], - p->psa_call_code[4], - p->psa_call_code[5], - p->psa_call_code[6], - p->psa_call_code[7]); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "psa_reserved[]: %02X:%02X\n", - p->psa_reserved[0], - p->psa_reserved[1]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "psa_conf_status: %d, ", p->psa_conf_status); - printk("psa_crc: 0x%02x%02x, ", p->psa_crc[0], p->psa_crc[1]); - printk("psa_crc_status: 0x%02x\n", p->psa_crc_status); -} /* wv_psa_show */ -#endif /* DEBUG_PSA_SHOW */ - -#ifdef DEBUG_MMC_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the Modem Management Controller. - * This function need to be completed... - */ -static void -wv_mmc_show(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - net_local * lp = netdev_priv(dev); - mmr_t m; - - /* Basic check */ - if(hasr_read(base) & HASR_NO_CLK) - { - printk(KERN_WARNING "%s: wv_mmc_show: modem not connected\n", - dev->name); - return; - } - - spin_lock_irqsave(&lp->spinlock, flags); - - /* Read the mmc */ - mmc_out(base, mmwoff(0, mmw_freeze), 1); - mmc_read(base, 0, (u_char *)&m, sizeof(m)); - mmc_out(base, mmwoff(0, mmw_freeze), 0); - - /* Don't forget to update statistics */ - lp->wstats.discard.nwid += (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l; - - spin_unlock_irqrestore(&lp->spinlock, flags); - - printk(KERN_DEBUG "##### wavelan modem status registers: #####\n"); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "mmc_unused0[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n", - m.mmr_unused0[0], - m.mmr_unused0[1], - m.mmr_unused0[2], - m.mmr_unused0[3], - m.mmr_unused0[4], - m.mmr_unused0[5], - m.mmr_unused0[6], - m.mmr_unused0[7]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "Encryption algorithm: %02X - Status: %02X\n", - m.mmr_des_avail, m.mmr_des_status); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "mmc_unused1[]: %02X:%02X:%02X:%02X:%02X\n", - m.mmr_unused1[0], - m.mmr_unused1[1], - m.mmr_unused1[2], - m.mmr_unused1[3], - m.mmr_unused1[4]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "dce_status: 0x%x [%s%s%s%s]\n", - m.mmr_dce_status, - (m.mmr_dce_status & MMR_DCE_STATUS_RX_BUSY) ? "energy detected,":"", - (m.mmr_dce_status & MMR_DCE_STATUS_LOOPT_IND) ? - "loop test indicated," : "", - (m.mmr_dce_status & MMR_DCE_STATUS_TX_BUSY) ? "transmitter on," : "", - (m.mmr_dce_status & MMR_DCE_STATUS_JBR_EXPIRED) ? - "jabber timer expired," : ""); - printk(KERN_DEBUG "Dsp ID: %02X\n", - m.mmr_dsp_id); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "mmc_unused2[]: %02X:%02X\n", - m.mmr_unused2[0], - m.mmr_unused2[1]); -#endif /* DEBUG_SHOW_UNUSED */ - printk(KERN_DEBUG "# correct_nwid: %d, # wrong_nwid: %d\n", - (m.mmr_correct_nwid_h << 8) | m.mmr_correct_nwid_l, - (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l); - printk(KERN_DEBUG "thr_pre_set: 0x%x [current signal %s]\n", - m.mmr_thr_pre_set & MMR_THR_PRE_SET, - (m.mmr_thr_pre_set & MMR_THR_PRE_SET_CUR) ? "above" : "below"); - printk(KERN_DEBUG "signal_lvl: %d [%s], ", - m.mmr_signal_lvl & MMR_SIGNAL_LVL, - (m.mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) ? "new msg" : "no new msg"); - printk("silence_lvl: %d [%s], ", m.mmr_silence_lvl & MMR_SILENCE_LVL, - (m.mmr_silence_lvl & MMR_SILENCE_LVL_VALID) ? "update done" : "no new update"); - printk("sgnl_qual: 0x%x [%s]\n", m.mmr_sgnl_qual & MMR_SGNL_QUAL, - (m.mmr_sgnl_qual & MMR_SGNL_QUAL_ANT) ? "Antenna 1" : "Antenna 0"); -#ifdef DEBUG_SHOW_UNUSED - printk(KERN_DEBUG "netw_id_l: %x\n", m.mmr_netw_id_l); -#endif /* DEBUG_SHOW_UNUSED */ -} /* wv_mmc_show */ -#endif /* DEBUG_MMC_SHOW */ - -#ifdef DEBUG_I82593_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the i82593's receive unit. - */ -static void -wv_ru_show(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - - printk(KERN_DEBUG "##### wavelan i82593 receiver status: #####\n"); - printk(KERN_DEBUG "ru: rfp %d stop %d", lp->rfp, lp->stop); - /* - * Not implemented yet... - */ - printk("\n"); -} /* wv_ru_show */ -#endif /* DEBUG_I82593_SHOW */ - -#ifdef DEBUG_DEVICE_SHOW -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the WaveLAN PCMCIA device driver. - */ -static void -wv_dev_show(struct net_device * dev) -{ - printk(KERN_DEBUG "dev:"); - printk(" state=%lX,", dev->state); - printk(" trans_start=%ld,", dev->trans_start); - printk(" flags=0x%x,", dev->flags); - printk("\n"); -} /* wv_dev_show */ - -/*------------------------------------------------------------------*/ -/* - * Print the formatted status of the WaveLAN PCMCIA device driver's - * private information. - */ -static void -wv_local_show(struct net_device * dev) -{ - net_local *lp = netdev_priv(dev); - - printk(KERN_DEBUG "local:"); - /* - * Not implemented yet... - */ - printk("\n"); -} /* wv_local_show */ -#endif /* DEBUG_DEVICE_SHOW */ - -#if defined(DEBUG_RX_INFO) || defined(DEBUG_TX_INFO) -/*------------------------------------------------------------------*/ -/* - * Dump packet header (and content if necessary) on the screen - */ -static void -wv_packet_info(u_char * p, /* Packet to dump */ - int length, /* Length of the packet */ - char * msg1, /* Name of the device */ - char * msg2) /* Name of the function */ -{ - int i; - int maxi; - - printk(KERN_DEBUG "%s: %s(): dest %pM, length %d\n", - msg1, msg2, p, length); - printk(KERN_DEBUG "%s: %s(): src %pM, type 0x%02X%02X\n", - msg1, msg2, &p[6], p[12], p[13]); - -#ifdef DEBUG_PACKET_DUMP - - printk(KERN_DEBUG "data=\""); - - if((maxi = length) > DEBUG_PACKET_DUMP) - maxi = DEBUG_PACKET_DUMP; - for(i = 14; i < maxi; i++) - if(p[i] >= ' ' && p[i] <= '~') - printk(" %c", p[i]); - else - printk("%02X", p[i]); - if(maxi < length) - printk(".."); - printk("\"\n"); - printk(KERN_DEBUG "\n"); -#endif /* DEBUG_PACKET_DUMP */ -} -#endif /* defined(DEBUG_RX_INFO) || defined(DEBUG_TX_INFO) */ - -/*------------------------------------------------------------------*/ -/* - * This is the information which is displayed by the driver at startup - * There is a lot of flag to configure it at your will... - */ -static void -wv_init_info(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - psa_t psa; - - /* Read the parameter storage area */ - psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa)); - -#ifdef DEBUG_PSA_SHOW - wv_psa_show(&psa); -#endif -#ifdef DEBUG_MMC_SHOW - wv_mmc_show(dev); -#endif -#ifdef DEBUG_I82593_SHOW - wv_ru_show(dev); -#endif - -#ifdef DEBUG_BASIC_SHOW - /* Now, let's go for the basic stuff */ - printk(KERN_NOTICE "%s: WaveLAN: port %#x, irq %d, hw_addr %pM", - dev->name, base, dev->irq, dev->dev_addr); - - /* Print current network id */ - if(psa.psa_nwid_select) - printk(", nwid 0x%02X-%02X", psa.psa_nwid[0], psa.psa_nwid[1]); - else - printk(", nwid off"); - - /* If 2.00 card */ - if(!(mmc_in(base, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) - { - unsigned short freq; - - /* Ask the EEprom to read the frequency from the first area */ - fee_read(base, 0x00 /* 1st area - frequency... */, - &freq, 1); - - /* Print frequency */ - printk(", 2.00, %ld", (freq >> 6) + 2400L); - - /* Hack !!! */ - if(freq & 0x20) - printk(".5"); - } - else - { - printk(", PCMCIA, "); - switch (psa.psa_subband) - { - case PSA_SUBBAND_915: - printk("915"); - break; - case PSA_SUBBAND_2425: - printk("2425"); - break; - case PSA_SUBBAND_2460: - printk("2460"); - break; - case PSA_SUBBAND_2484: - printk("2484"); - break; - case PSA_SUBBAND_2430_5: - printk("2430.5"); - break; - default: - printk("unknown"); - } - } - - printk(" MHz\n"); -#endif /* DEBUG_BASIC_SHOW */ - -#ifdef DEBUG_VERSION_SHOW - /* Print version information */ - printk(KERN_NOTICE "%s", version); -#endif -} /* wv_init_info */ - -/********************* IOCTL, STATS & RECONFIG *********************/ -/* - * We found here routines that are called by Linux on differents - * occasions after the configuration and not for transmitting data - * These may be called when the user use ifconfig, /proc/net/dev - * or wireless extensions - */ - - -/*------------------------------------------------------------------*/ -/* - * Set or clear the multicast filter for this adaptor. - * num_addrs == -1 Promiscuous mode, receive all packets - * num_addrs == 0 Normal mode, clear multicast list - * num_addrs > 0 Multicast mode, receive normal and MC packets, - * and do best-effort filtering. - */ - -static void -wavelan_set_multicast_list(struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: ->wavelan_set_multicast_list()\n", dev->name); -#endif - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "%s: wavelan_set_multicast_list(): setting Rx mode %02X to %d addresses.\n", - dev->name, dev->flags, dev->mc_count); -#endif - - if(dev->flags & IFF_PROMISC) - { - /* - * Enable promiscuous mode: receive all packets. - */ - if(!lp->promiscuous) - { - lp->promiscuous = 1; - lp->allmulticast = 0; - lp->mc_count = 0; - - wv_82593_reconfig(dev); - } - } - else - /* If all multicast addresses - * or too much multicast addresses for the hardware filter */ - if((dev->flags & IFF_ALLMULTI) || - (dev->mc_count > I82593_MAX_MULTICAST_ADDRESSES)) - { - /* - * Disable promiscuous mode, but active the all multicast mode - */ - if(!lp->allmulticast) - { - lp->promiscuous = 0; - lp->allmulticast = 1; - lp->mc_count = 0; - - wv_82593_reconfig(dev); - } - } - else - /* If there is some multicast addresses to send */ - if(dev->mc_list != (struct dev_mc_list *) NULL) - { - /* - * Disable promiscuous mode, but receive all packets - * in multicast list - */ -#ifdef MULTICAST_AVOID - if(lp->promiscuous || lp->allmulticast || - (dev->mc_count != lp->mc_count)) -#endif - { - lp->promiscuous = 0; - lp->allmulticast = 0; - lp->mc_count = dev->mc_count; - - wv_82593_reconfig(dev); - } - } - else - { - /* - * Switch to normal mode: disable promiscuous mode and - * clear the multicast list. - */ - if(lp->promiscuous || lp->mc_count == 0) - { - lp->promiscuous = 0; - lp->allmulticast = 0; - lp->mc_count = 0; - - wv_82593_reconfig(dev); - } - } -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: <-wavelan_set_multicast_list()\n", dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * This function doesn't exist... - * (Note : it was a nice way to test the reconfigure stuff...) - */ -#ifdef SET_MAC_ADDRESS -static int -wavelan_set_mac_address(struct net_device * dev, - void * addr) -{ - struct sockaddr * mac = addr; - - /* Copy the address */ - memcpy(dev->dev_addr, mac->sa_data, WAVELAN_ADDR_SIZE); - - /* Reconfig the beast */ - wv_82593_reconfig(dev); - - return 0; -} -#endif /* SET_MAC_ADDRESS */ - - -/*------------------------------------------------------------------*/ -/* - * Frequency setting (for hardware able of it) - * It's a bit complicated and you don't really want to look into it... - */ -static int -wv_set_frequency(u_long base, /* i/o port of the card */ - iw_freq * frequency) -{ - const int BAND_NUM = 10; /* Number of bands */ - long freq = 0L; /* offset to 2.4 GHz in .5 MHz */ -#ifdef DEBUG_IOCTL_INFO - int i; -#endif - - /* Setting by frequency */ - /* Theoritically, you may set any frequency between - * the two limits with a 0.5 MHz precision. In practice, - * I don't want you to have trouble with local - * regulations... */ - if((frequency->e == 1) && - (frequency->m >= (int) 2.412e8) && (frequency->m <= (int) 2.487e8)) - { - freq = ((frequency->m / 10000) - 24000L) / 5; - } - - /* Setting by channel (same as wfreqsel) */ - /* Warning : each channel is 22MHz wide, so some of the channels - * will interfere... */ - if((frequency->e == 0) && - (frequency->m >= 0) && (frequency->m < BAND_NUM)) - { - /* Get frequency offset. */ - freq = channel_bands[frequency->m] >> 1; - } - - /* Verify if the frequency is allowed */ - if(freq != 0L) - { - u_short table[10]; /* Authorized frequency table */ - - /* Read the frequency table */ - fee_read(base, 0x71 /* frequency table */, - table, 10); - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "Frequency table :"); - for(i = 0; i < 10; i++) - { - printk(" %04X", - table[i]); - } - printk("\n"); -#endif - - /* Look in the table if the frequency is allowed */ - if(!(table[9 - ((freq - 24) / 16)] & - (1 << ((freq - 24) % 16)))) - return -EINVAL; /* not allowed */ - } - else - return -EINVAL; - - /* If we get a usable frequency */ - if(freq != 0L) - { - unsigned short area[16]; - unsigned short dac[2]; - unsigned short area_verify[16]; - unsigned short dac_verify[2]; - /* Corresponding gain (in the power adjust value table) - * see AT&T Wavelan Data Manual, REF 407-024689/E, page 3-8 - * & WCIN062D.DOC, page 6.2.9 */ - unsigned short power_limit[] = { 40, 80, 120, 160, 0 }; - int power_band = 0; /* Selected band */ - unsigned short power_adjust; /* Correct value */ - - /* Search for the gain */ - power_band = 0; - while((freq > power_limit[power_band]) && - (power_limit[++power_band] != 0)) - ; - - /* Read the first area */ - fee_read(base, 0x00, - area, 16); - - /* Read the DAC */ - fee_read(base, 0x60, - dac, 2); - - /* Read the new power adjust value */ - fee_read(base, 0x6B - (power_band >> 1), - &power_adjust, 1); - if(power_band & 0x1) - power_adjust >>= 8; - else - power_adjust &= 0xFF; - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "Wavelan EEprom Area 1 :"); - for(i = 0; i < 16; i++) - { - printk(" %04X", - area[i]); - } - printk("\n"); - - printk(KERN_DEBUG "Wavelan EEprom DAC : %04X %04X\n", - dac[0], dac[1]); -#endif - - /* Frequency offset (for info only...) */ - area[0] = ((freq << 5) & 0xFFE0) | (area[0] & 0x1F); - - /* Receiver Principle main divider coefficient */ - area[3] = (freq >> 1) + 2400L - 352L; - area[2] = ((freq & 0x1) << 4) | (area[2] & 0xFFEF); - - /* Transmitter Main divider coefficient */ - area[13] = (freq >> 1) + 2400L; - area[12] = ((freq & 0x1) << 4) | (area[2] & 0xFFEF); - - /* Others part of the area are flags, bit streams or unused... */ - - /* Set the value in the DAC */ - dac[1] = ((power_adjust >> 1) & 0x7F) | (dac[1] & 0xFF80); - dac[0] = ((power_adjust & 0x1) << 4) | (dac[0] & 0xFFEF); - - /* Write the first area */ - fee_write(base, 0x00, - area, 16); - - /* Write the DAC */ - fee_write(base, 0x60, - dac, 2); - - /* We now should verify here that the EEprom writing was ok */ - - /* ReRead the first area */ - fee_read(base, 0x00, - area_verify, 16); - - /* ReRead the DAC */ - fee_read(base, 0x60, - dac_verify, 2); - - /* Compare */ - if(memcmp(area, area_verify, 16 * 2) || - memcmp(dac, dac_verify, 2 * 2)) - { -#ifdef DEBUG_IOCTL_ERROR - printk(KERN_INFO "Wavelan: wv_set_frequency : unable to write new frequency to EEprom (?)\n"); -#endif - return -EOPNOTSUPP; - } - - /* We must download the frequency parameters to the - * synthetisers (from the EEprom - area 1) - * Note : as the EEprom is auto decremented, we set the end - * if the area... */ - mmc_out(base, mmwoff(0, mmw_fee_addr), 0x0F); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), - MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD); - - /* Wait until the download is finished */ - fee_wait(base, 100, 100); - - /* We must now download the power adjust value (gain) to - * the synthetisers (from the EEprom - area 7 - DAC) */ - mmc_out(base, mmwoff(0, mmw_fee_addr), 0x61); - mmc_out(base, mmwoff(0, mmw_fee_ctrl), - MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD); - - /* Wait until the download is finished */ - fee_wait(base, 100, 100); - -#ifdef DEBUG_IOCTL_INFO - /* Verification of what we have done... */ - - printk(KERN_DEBUG "Wavelan EEprom Area 1 :"); - for(i = 0; i < 16; i++) - { - printk(" %04X", - area_verify[i]); - } - printk("\n"); - - printk(KERN_DEBUG "Wavelan EEprom DAC : %04X %04X\n", - dac_verify[0], dac_verify[1]); -#endif - - return 0; - } - else - return -EINVAL; /* Bah, never get there... */ -} - -/*------------------------------------------------------------------*/ -/* - * Give the list of available frequencies - */ -static int -wv_frequency_list(u_long base, /* i/o port of the card */ - iw_freq * list, /* List of frequency to fill */ - int max) /* Maximum number of frequencies */ -{ - u_short table[10]; /* Authorized frequency table */ - long freq = 0L; /* offset to 2.4 GHz in .5 MHz + 12 MHz */ - int i; /* index in the table */ - const int BAND_NUM = 10; /* Number of bands */ - int c = 0; /* Channel number */ - - /* Read the frequency table */ - fee_read(base, 0x71 /* frequency table */, - table, 10); - - /* Look all frequencies */ - i = 0; - for(freq = 0; freq < 150; freq++) - /* Look in the table if the frequency is allowed */ - if(table[9 - (freq / 16)] & (1 << (freq % 16))) - { - /* Compute approximate channel number */ - while((((channel_bands[c] >> 1) - 24) < freq) && - (c < BAND_NUM)) - c++; - list[i].i = c; /* Set the list index */ - - /* put in the list */ - list[i].m = (((freq + 24) * 5) + 24000L) * 10000; - list[i++].e = 1; - - /* Check number */ - if(i >= max) - return(i); - } - - return(i); -} - -#ifdef IW_WIRELESS_SPY -/*------------------------------------------------------------------*/ -/* - * Gather wireless spy statistics : for each packet, compare the source - * address with out list, and if match, get the stats... - * Sorry, but this function really need wireless extensions... - */ -static inline void -wl_spy_gather(struct net_device * dev, - u_char * mac, /* MAC address */ - u_char * stats) /* Statistics to gather */ -{ - struct iw_quality wstats; - - wstats.qual = stats[2] & MMR_SGNL_QUAL; - wstats.level = stats[0] & MMR_SIGNAL_LVL; - wstats.noise = stats[1] & MMR_SILENCE_LVL; - wstats.updated = 0x7; - - /* Update spy records */ - wireless_spy_update(dev, mac, &wstats); -} -#endif /* IW_WIRELESS_SPY */ - -#ifdef HISTOGRAM -/*------------------------------------------------------------------*/ -/* - * This function calculate an histogram on the signal level. - * As the noise is quite constant, it's like doing it on the SNR. - * We have defined a set of interval (lp->his_range), and each time - * the level goes in that interval, we increment the count (lp->his_sum). - * With this histogram you may detect if one wavelan is really weak, - * or you may also calculate the mean and standard deviation of the level... - */ -static inline void -wl_his_gather(struct net_device * dev, - u_char * stats) /* Statistics to gather */ -{ - net_local * lp = netdev_priv(dev); - u_char level = stats[0] & MMR_SIGNAL_LVL; - int i; - - /* Find the correct interval */ - i = 0; - while((i < (lp->his_number - 1)) && (level >= lp->his_range[i++])) - ; - - /* Increment interval counter */ - (lp->his_sum[i])++; -} -#endif /* HISTOGRAM */ - -static void wl_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) -{ - strncpy(info->driver, "wavelan_cs", sizeof(info->driver)-1); -} - -static const struct ethtool_ops ops = { - .get_drvinfo = wl_get_drvinfo -}; - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get protocol name - */ -static int wavelan_get_name(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - strcpy(wrqu->name, "WaveLAN"); - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set NWID - */ -static int wavelan_set_nwid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - mm_t m; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Set NWID in WaveLAN. */ - if (!wrqu->nwid.disabled) { - /* Set NWID in psa */ - psa.psa_nwid[0] = (wrqu->nwid.value & 0xFF00) >> 8; - psa.psa_nwid[1] = wrqu->nwid.value & 0xFF; - psa.psa_nwid_select = 0x01; - psa_write(dev, - (char *) psa.psa_nwid - (char *) &psa, - (unsigned char *) psa.psa_nwid, 3); - - /* Set NWID in mmc. */ - m.w.mmw_netw_id_l = psa.psa_nwid[1]; - m.w.mmw_netw_id_h = psa.psa_nwid[0]; - mmc_write(base, - (char *) &m.w.mmw_netw_id_l - - (char *) &m, - (unsigned char *) &m.w.mmw_netw_id_l, 2); - mmc_out(base, mmwoff(0, mmw_loopt_sel), 0x00); - } else { - /* Disable NWID in the psa. */ - psa.psa_nwid_select = 0x00; - psa_write(dev, - (char *) &psa.psa_nwid_select - - (char *) &psa, - (unsigned char *) &psa.psa_nwid_select, - 1); - - /* Disable NWID in the mmc (no filtering). */ - mmc_out(base, mmwoff(0, mmw_loopt_sel), - MMW_LOOPT_SEL_DIS_NWID); - } - /* update the Wavelan checksum */ - update_psa_checksum(dev); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get NWID - */ -static int wavelan_get_nwid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Read the NWID. */ - psa_read(dev, - (char *) psa.psa_nwid - (char *) &psa, - (unsigned char *) psa.psa_nwid, 3); - wrqu->nwid.value = (psa.psa_nwid[0] << 8) + psa.psa_nwid[1]; - wrqu->nwid.disabled = !(psa.psa_nwid_select); - wrqu->nwid.fixed = 1; /* Superfluous */ - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set frequency - */ -static int wavelan_set_freq(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - unsigned long flags; - int ret; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). */ - if (!(mmc_in(base, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) - ret = wv_set_frequency(base, &(wrqu->freq)); - else - ret = -EOPNOTSUPP; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get frequency - */ -static int wavelan_get_freq(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). - * Does it work for everybody, especially old cards? */ - if (!(mmc_in(base, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) { - unsigned short freq; - - /* Ask the EEPROM to read the frequency from the first area. */ - fee_read(base, 0x00, &freq, 1); - wrqu->freq.m = ((freq >> 5) * 5 + 24000L) * 10000; - wrqu->freq.e = 1; - } else { - psa_read(dev, - (char *) &psa.psa_subband - (char *) &psa, - (unsigned char *) &psa.psa_subband, 1); - - if (psa.psa_subband <= 4) { - wrqu->freq.m = fixed_bands[psa.psa_subband]; - wrqu->freq.e = (psa.psa_subband != 0); - } else - ret = -EOPNOTSUPP; - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set level threshold - */ -static int wavelan_set_sens(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Set the level threshold. */ - /* We should complain loudly if wrqu->sens.fixed = 0, because we - * can't set auto mode... */ - psa.psa_thr_pre_set = wrqu->sens.value & 0x3F; - psa_write(dev, - (char *) &psa.psa_thr_pre_set - (char *) &psa, - (unsigned char *) &psa.psa_thr_pre_set, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev); - mmc_out(base, mmwoff(0, mmw_thr_pre_set), - psa.psa_thr_pre_set); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get level threshold - */ -static int wavelan_get_sens(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Read the level threshold. */ - psa_read(dev, - (char *) &psa.psa_thr_pre_set - (char *) &psa, - (unsigned char *) &psa.psa_thr_pre_set, 1); - wrqu->sens.value = psa.psa_thr_pre_set & 0x3F; - wrqu->sens.fixed = 1; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set encryption key - */ -static int wavelan_set_encode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - unsigned long flags; - psa_t psa; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check if capable of encryption */ - if (!mmc_encr(base)) { - ret = -EOPNOTSUPP; - } - - /* Check the size of the key */ - if((wrqu->encoding.length != 8) && (wrqu->encoding.length != 0)) { - ret = -EINVAL; - } - - if(!ret) { - /* Basic checking... */ - if (wrqu->encoding.length == 8) { - /* Copy the key in the driver */ - memcpy(psa.psa_encryption_key, extra, - wrqu->encoding.length); - psa.psa_encryption_select = 1; - - psa_write(dev, - (char *) &psa.psa_encryption_select - - (char *) &psa, - (unsigned char *) &psa. - psa_encryption_select, 8 + 1); - - mmc_out(base, mmwoff(0, mmw_encr_enable), - MMW_ENCR_ENABLE_EN | MMW_ENCR_ENABLE_MODE); - mmc_write(base, mmwoff(0, mmw_encr_key), - (unsigned char *) &psa. - psa_encryption_key, 8); - } - - /* disable encryption */ - if (wrqu->encoding.flags & IW_ENCODE_DISABLED) { - psa.psa_encryption_select = 0; - psa_write(dev, - (char *) &psa.psa_encryption_select - - (char *) &psa, - (unsigned char *) &psa. - psa_encryption_select, 1); - - mmc_out(base, mmwoff(0, mmw_encr_enable), 0); - } - /* update the Wavelan checksum */ - update_psa_checksum(dev); - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get encryption key - */ -static int wavelan_get_encode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check if encryption is available */ - if (!mmc_encr(base)) { - ret = -EOPNOTSUPP; - } else { - /* Read the encryption key */ - psa_read(dev, - (char *) &psa.psa_encryption_select - - (char *) &psa, - (unsigned char *) &psa. - psa_encryption_select, 1 + 8); - - /* encryption is enabled ? */ - if (psa.psa_encryption_select) - wrqu->encoding.flags = IW_ENCODE_ENABLED; - else - wrqu->encoding.flags = IW_ENCODE_DISABLED; - wrqu->encoding.flags |= mmc_encr(base); - - /* Copy the key to the user buffer */ - wrqu->encoding.length = 8; - memcpy(extra, psa.psa_encryption_key, wrqu->encoding.length); - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -#ifdef WAVELAN_ROAMING_EXT -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set ESSID (domain) - */ -static int wavelan_set_essid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check if disable */ - if(wrqu->data.flags == 0) - lp->filter_domains = 0; - else { - char essid[IW_ESSID_MAX_SIZE + 1]; - char * endp; - - /* Terminate the string */ - memcpy(essid, extra, wrqu->data.length); - essid[IW_ESSID_MAX_SIZE] = '\0'; - -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "SetEssid : ``%s''\n", essid); -#endif /* DEBUG_IOCTL_INFO */ - - /* Convert to a number (note : Wavelan specific) */ - lp->domain_id = simple_strtoul(essid, &endp, 16); - /* Has it worked ? */ - if(endp > essid) - lp->filter_domains = 1; - else { - lp->filter_domains = 0; - ret = -EINVAL; - } - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get ESSID (domain) - */ -static int wavelan_get_essid(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - - /* Is the domain ID active ? */ - wrqu->data.flags = lp->filter_domains; - - /* Copy Domain ID into a string (Wavelan specific) */ - /* Sound crazy, be we can't have a snprintf in the kernel !!! */ - sprintf(extra, "%lX", lp->domain_id); - extra[IW_ESSID_MAX_SIZE] = '\0'; - - /* Set the length */ - wrqu->data.length = strlen(extra); - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set AP address - */ -static int wavelan_set_wap(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ -#ifdef DEBUG_IOCTL_INFO - printk(KERN_DEBUG "Set AP to : %pM\n", wrqu->ap_addr.sa_data); -#endif /* DEBUG_IOCTL_INFO */ - - return -EOPNOTSUPP; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get AP address - */ -static int wavelan_get_wap(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - /* Should get the real McCoy instead of own Ethernet address */ - memcpy(wrqu->ap_addr.sa_data, dev->dev_addr, WAVELAN_ADDR_SIZE); - wrqu->ap_addr.sa_family = ARPHRD_ETHER; - - return -EOPNOTSUPP; -} -#endif /* WAVELAN_ROAMING_EXT */ - -#ifdef WAVELAN_ROAMING -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : set mode - */ -static int wavelan_set_mode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - int ret = 0; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Check mode */ - switch(wrqu->mode) { - case IW_MODE_ADHOC: - if(do_roaming) { - wv_roam_cleanup(dev); - do_roaming = 0; - } - break; - case IW_MODE_INFRA: - if(!do_roaming) { - wv_roam_init(dev); - do_roaming = 1; - } - break; - default: - ret = -EINVAL; - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get mode - */ -static int wavelan_get_mode(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - if(do_roaming) - wrqu->mode = IW_MODE_INFRA; - else - wrqu->mode = IW_MODE_ADHOC; - - return 0; -} -#endif /* WAVELAN_ROAMING */ - -/*------------------------------------------------------------------*/ -/* - * Wireless Handler : get range info - */ -static int wavelan_get_range(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - struct iw_range *range = (struct iw_range *) extra; - unsigned long flags; - int ret = 0; - - /* Set the length (very important for backward compatibility) */ - wrqu->data.length = sizeof(struct iw_range); - - /* Set all the info we don't care or don't know about to zero */ - memset(range, 0, sizeof(struct iw_range)); - - /* Set the Wireless Extension versions */ - range->we_version_compiled = WIRELESS_EXT; - range->we_version_source = 9; - - /* Set information in the range struct. */ - range->throughput = 1.4 * 1000 * 1000; /* don't argue on this ! */ - range->min_nwid = 0x0000; - range->max_nwid = 0xFFFF; - - range->sensitivity = 0x3F; - range->max_qual.qual = MMR_SGNL_QUAL; - range->max_qual.level = MMR_SIGNAL_LVL; - range->max_qual.noise = MMR_SILENCE_LVL; - range->avg_qual.qual = MMR_SGNL_QUAL; /* Always max */ - /* Need to get better values for those two */ - range->avg_qual.level = 30; - range->avg_qual.noise = 8; - - range->num_bitrates = 1; - range->bitrate[0] = 2000000; /* 2 Mb/s */ - - /* Event capability (kernel + driver) */ - range->event_capa[0] = (IW_EVENT_CAPA_MASK(0x8B02) | - IW_EVENT_CAPA_MASK(0x8B04) | - IW_EVENT_CAPA_MASK(0x8B06)); - range->event_capa[1] = IW_EVENT_CAPA_K_1; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). */ - if (!(mmc_in(base, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) { - range->num_channels = 10; - range->num_frequency = wv_frequency_list(base, range->freq, - IW_MAX_FREQUENCIES); - } else - range->num_channels = range->num_frequency = 0; - - /* Encryption supported ? */ - if (mmc_encr(base)) { - range->encoding_size[0] = 8; /* DES = 64 bits key */ - range->num_encoding_sizes = 1; - range->max_encoding_tokens = 1; /* Only one key possible */ - } else { - range->num_encoding_sizes = 0; - range->max_encoding_tokens = 0; - } - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return ret; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : set quality threshold - */ -static int wavelan_set_qthr(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - unsigned int base = dev->base_addr; - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - psa.psa_quality_thr = *(extra) & 0x0F; - psa_write(dev, - (char *) &psa.psa_quality_thr - (char *) &psa, - (unsigned char *) &psa.psa_quality_thr, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev); - mmc_out(base, mmwoff(0, mmw_quality_thr), - psa.psa_quality_thr); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : get quality threshold - */ -static int wavelan_get_qthr(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - psa_t psa; - unsigned long flags; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - psa_read(dev, - (char *) &psa.psa_quality_thr - (char *) &psa, - (unsigned char *) &psa.psa_quality_thr, 1); - *(extra) = psa.psa_quality_thr & 0x0F; - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return 0; -} - -#ifdef WAVELAN_ROAMING -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : set roaming - */ -static int wavelan_set_roam(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - unsigned long flags; - - /* Disable interrupts and save flags. */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Note : should check if user == root */ - if(do_roaming && (*extra)==0) - wv_roam_cleanup(dev); - else if(do_roaming==0 && (*extra)!=0) - wv_roam_init(dev); - - do_roaming = (*extra); - - /* Enable interrupts and restore flags. */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : get quality threshold - */ -static int wavelan_get_roam(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - *(extra) = do_roaming; - - return 0; -} -#endif /* WAVELAN_ROAMING */ - -#ifdef HISTOGRAM -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : set histogram - */ -static int wavelan_set_histo(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - - /* Check the number of intervals. */ - if (wrqu->data.length > 16) { - return(-E2BIG); - } - - /* Disable histo while we copy the addresses. - * As we don't disable interrupts, we need to do this */ - lp->his_number = 0; - - /* Are there ranges to copy? */ - if (wrqu->data.length > 0) { - /* Copy interval ranges to the driver */ - memcpy(lp->his_range, extra, wrqu->data.length); - - { - int i; - printk(KERN_DEBUG "Histo :"); - for(i = 0; i < wrqu->data.length; i++) - printk(" %d", lp->his_range[i]); - printk("\n"); - } - - /* Reset result structure. */ - memset(lp->his_sum, 0x00, sizeof(long) * 16); - } - - /* Now we can set the number of ranges */ - lp->his_number = wrqu->data.length; - - return(0); -} - -/*------------------------------------------------------------------*/ -/* - * Wireless Private Handler : get histogram - */ -static int wavelan_get_histo(struct net_device *dev, - struct iw_request_info *info, - union iwreq_data *wrqu, - char *extra) -{ - net_local *lp = netdev_priv(dev); - - /* Set the number of intervals. */ - wrqu->data.length = lp->his_number; - - /* Give back the distribution statistics */ - if(lp->his_number > 0) - memcpy(extra, lp->his_sum, sizeof(long) * lp->his_number); - - return(0); -} -#endif /* HISTOGRAM */ - -/*------------------------------------------------------------------*/ -/* - * Structures to export the Wireless Handlers - */ - -static const struct iw_priv_args wavelan_private_args[] = { -/*{ cmd, set_args, get_args, name } */ - { SIOCSIPQTHR, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, 0, "setqualthr" }, - { SIOCGIPQTHR, 0, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, "getqualthr" }, - { SIOCSIPROAM, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, 0, "setroam" }, - { SIOCGIPROAM, 0, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, "getroam" }, - { SIOCSIPHISTO, IW_PRIV_TYPE_BYTE | 16, 0, "sethisto" }, - { SIOCGIPHISTO, 0, IW_PRIV_TYPE_INT | 16, "gethisto" }, -}; - -static const iw_handler wavelan_handler[] = -{ - NULL, /* SIOCSIWNAME */ - wavelan_get_name, /* SIOCGIWNAME */ - wavelan_set_nwid, /* SIOCSIWNWID */ - wavelan_get_nwid, /* SIOCGIWNWID */ - wavelan_set_freq, /* SIOCSIWFREQ */ - wavelan_get_freq, /* SIOCGIWFREQ */ -#ifdef WAVELAN_ROAMING - wavelan_set_mode, /* SIOCSIWMODE */ - wavelan_get_mode, /* SIOCGIWMODE */ -#else /* WAVELAN_ROAMING */ - NULL, /* SIOCSIWMODE */ - NULL, /* SIOCGIWMODE */ -#endif /* WAVELAN_ROAMING */ - wavelan_set_sens, /* SIOCSIWSENS */ - wavelan_get_sens, /* SIOCGIWSENS */ - NULL, /* SIOCSIWRANGE */ - wavelan_get_range, /* SIOCGIWRANGE */ - NULL, /* SIOCSIWPRIV */ - NULL, /* SIOCGIWPRIV */ - NULL, /* SIOCSIWSTATS */ - NULL, /* SIOCGIWSTATS */ - iw_handler_set_spy, /* SIOCSIWSPY */ - iw_handler_get_spy, /* SIOCGIWSPY */ - iw_handler_set_thrspy, /* SIOCSIWTHRSPY */ - iw_handler_get_thrspy, /* SIOCGIWTHRSPY */ -#ifdef WAVELAN_ROAMING_EXT - wavelan_set_wap, /* SIOCSIWAP */ - wavelan_get_wap, /* SIOCGIWAP */ - NULL, /* -- hole -- */ - NULL, /* SIOCGIWAPLIST */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - wavelan_set_essid, /* SIOCSIWESSID */ - wavelan_get_essid, /* SIOCGIWESSID */ -#else /* WAVELAN_ROAMING_EXT */ - NULL, /* SIOCSIWAP */ - NULL, /* SIOCGIWAP */ - NULL, /* -- hole -- */ - NULL, /* SIOCGIWAPLIST */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWESSID */ - NULL, /* SIOCGIWESSID */ -#endif /* WAVELAN_ROAMING_EXT */ - NULL, /* SIOCSIWNICKN */ - NULL, /* SIOCGIWNICKN */ - NULL, /* -- hole -- */ - NULL, /* -- hole -- */ - NULL, /* SIOCSIWRATE */ - NULL, /* SIOCGIWRATE */ - NULL, /* SIOCSIWRTS */ - NULL, /* SIOCGIWRTS */ - NULL, /* SIOCSIWFRAG */ - NULL, /* SIOCGIWFRAG */ - NULL, /* SIOCSIWTXPOW */ - NULL, /* SIOCGIWTXPOW */ - NULL, /* SIOCSIWRETRY */ - NULL, /* SIOCGIWRETRY */ - wavelan_set_encode, /* SIOCSIWENCODE */ - wavelan_get_encode, /* SIOCGIWENCODE */ -}; - -static const iw_handler wavelan_private_handler[] = -{ - wavelan_set_qthr, /* SIOCIWFIRSTPRIV */ - wavelan_get_qthr, /* SIOCIWFIRSTPRIV + 1 */ -#ifdef WAVELAN_ROAMING - wavelan_set_roam, /* SIOCIWFIRSTPRIV + 2 */ - wavelan_get_roam, /* SIOCIWFIRSTPRIV + 3 */ -#else /* WAVELAN_ROAMING */ - NULL, /* SIOCIWFIRSTPRIV + 2 */ - NULL, /* SIOCIWFIRSTPRIV + 3 */ -#endif /* WAVELAN_ROAMING */ -#ifdef HISTOGRAM - wavelan_set_histo, /* SIOCIWFIRSTPRIV + 4 */ - wavelan_get_histo, /* SIOCIWFIRSTPRIV + 5 */ -#endif /* HISTOGRAM */ -}; - -static const struct iw_handler_def wavelan_handler_def = -{ - .num_standard = ARRAY_SIZE(wavelan_handler), - .num_private = ARRAY_SIZE(wavelan_private_handler), - .num_private_args = ARRAY_SIZE(wavelan_private_args), - .standard = wavelan_handler, - .private = wavelan_private_handler, - .private_args = wavelan_private_args, - .get_wireless_stats = wavelan_get_wireless_stats, -}; - -/*------------------------------------------------------------------*/ -/* - * Get wireless statistics - * Called by /proc/net/wireless... - */ -static iw_stats * -wavelan_get_wireless_stats(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - net_local * lp = netdev_priv(dev); - mmr_t m; - iw_stats * wstats; - unsigned long flags; - -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: ->wavelan_get_wireless_stats()\n", dev->name); -#endif - - /* Disable interrupts & save flags */ - spin_lock_irqsave(&lp->spinlock, flags); - - wstats = &lp->wstats; - - /* Get data from the mmc */ - mmc_out(base, mmwoff(0, mmw_freeze), 1); - - mmc_read(base, mmroff(0, mmr_dce_status), &m.mmr_dce_status, 1); - mmc_read(base, mmroff(0, mmr_wrong_nwid_l), &m.mmr_wrong_nwid_l, 2); - mmc_read(base, mmroff(0, mmr_thr_pre_set), &m.mmr_thr_pre_set, 4); - - mmc_out(base, mmwoff(0, mmw_freeze), 0); - - /* Copy data to wireless stuff */ - wstats->status = m.mmr_dce_status & MMR_DCE_STATUS; - wstats->qual.qual = m.mmr_sgnl_qual & MMR_SGNL_QUAL; - wstats->qual.level = m.mmr_signal_lvl & MMR_SIGNAL_LVL; - wstats->qual.noise = m.mmr_silence_lvl & MMR_SILENCE_LVL; - wstats->qual.updated = (((m.mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) >> 7) | - ((m.mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) >> 6) | - ((m.mmr_silence_lvl & MMR_SILENCE_LVL_VALID) >> 5)); - wstats->discard.nwid += (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l; - wstats->discard.code = 0L; - wstats->discard.misc = 0L; - - /* ReEnable interrupts & restore flags */ - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_IOCTL_TRACE - printk(KERN_DEBUG "%s: <-wavelan_get_wireless_stats()\n", dev->name); -#endif - return &lp->wstats; -} - -/************************* PACKET RECEPTION *************************/ -/* - * This part deal with receiving the packets. - * The interrupt handler get an interrupt when a packet has been - * successfully received and called this part... - */ - -/*------------------------------------------------------------------*/ -/* - * Calculate the starting address of the frame pointed to by the receive - * frame pointer and verify that the frame seem correct - * (called by wv_packet_rcv()) - */ -static int -wv_start_of_frame(struct net_device * dev, - int rfp, /* end of frame */ - int wrap) /* start of buffer */ -{ - unsigned int base = dev->base_addr; - int rp; - int len; - - rp = (rfp - 5 + RX_SIZE) % RX_SIZE; - outb(rp & 0xff, PIORL(base)); - outb(((rp >> 8) & PIORH_MASK), PIORH(base)); - len = inb(PIOP(base)); - len |= inb(PIOP(base)) << 8; - - /* Sanity checks on size */ - /* Frame too big */ - if(len > MAXDATAZ + 100) - { -#ifdef DEBUG_RX_ERROR - printk(KERN_INFO "%s: wv_start_of_frame: Received frame too large, rfp %d len 0x%x\n", - dev->name, rfp, len); -#endif - return(-1); - } - - /* Frame too short */ - if(len < 7) - { -#ifdef DEBUG_RX_ERROR - printk(KERN_INFO "%s: wv_start_of_frame: Received null frame, rfp %d len 0x%x\n", - dev->name, rfp, len); -#endif - return(-1); - } - - /* Wrap around buffer */ - if(len > ((wrap - (rfp - len) + RX_SIZE) % RX_SIZE)) /* magic formula ! */ - { -#ifdef DEBUG_RX_ERROR - printk(KERN_INFO "%s: wv_start_of_frame: wrap around buffer, wrap %d rfp %d len 0x%x\n", - dev->name, wrap, rfp, len); -#endif - return(-1); - } - - return((rp - len + RX_SIZE) % RX_SIZE); -} /* wv_start_of_frame */ - -/*------------------------------------------------------------------*/ -/* - * This routine does the actual copy of data (including the ethernet - * header structure) from the WaveLAN card to an sk_buff chain that - * will be passed up to the network interface layer. NOTE: We - * currently don't handle trailer protocols (neither does the rest of - * the network interface), so if that is needed, it will (at least in - * part) be added here. The contents of the receive ring buffer are - * copied to a message chain that is then passed to the kernel. - * - * Note: if any errors occur, the packet is "dropped on the floor" - * (called by wv_packet_rcv()) - */ -static void -wv_packet_read(struct net_device * dev, - int fd_p, - int sksize) -{ - net_local * lp = netdev_priv(dev); - struct sk_buff * skb; - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: ->wv_packet_read(0x%X, %d)\n", - dev->name, fd_p, sksize); -#endif - - /* Allocate some buffer for the new packet */ - if((skb = dev_alloc_skb(sksize+2)) == (struct sk_buff *) NULL) - { -#ifdef DEBUG_RX_ERROR - printk(KERN_INFO "%s: wv_packet_read(): could not alloc_skb(%d, GFP_ATOMIC)\n", - dev->name, sksize); -#endif - dev->stats.rx_dropped++; - /* - * Not only do we want to return here, but we also need to drop the - * packet on the floor to clear the interrupt. - */ - return; - } - - skb_reserve(skb, 2); - fd_p = read_ringbuf(dev, fd_p, (char *) skb_put(skb, sksize), sksize); - skb->protocol = eth_type_trans(skb, dev); - -#ifdef DEBUG_RX_INFO - wv_packet_info(skb_mac_header(skb), sksize, dev->name, "wv_packet_read"); -#endif /* DEBUG_RX_INFO */ - - /* Statistics gathering & stuff associated. - * It seem a bit messy with all the define, but it's really simple... */ - if( -#ifdef IW_WIRELESS_SPY - (lp->spy_data.spy_number > 0) || -#endif /* IW_WIRELESS_SPY */ -#ifdef HISTOGRAM - (lp->his_number > 0) || -#endif /* HISTOGRAM */ -#ifdef WAVELAN_ROAMING - (do_roaming) || -#endif /* WAVELAN_ROAMING */ - 0) - { - u_char stats[3]; /* Signal level, Noise level, Signal quality */ - - /* read signal level, silence level and signal quality bytes */ - fd_p = read_ringbuf(dev, (fd_p + 4) % RX_SIZE + RX_BASE, - stats, 3); -#ifdef DEBUG_RX_INFO - printk(KERN_DEBUG "%s: wv_packet_read(): Signal level %d/63, Silence level %d/63, signal quality %d/16\n", - dev->name, stats[0] & 0x3F, stats[1] & 0x3F, stats[2] & 0x0F); -#endif - -#ifdef WAVELAN_ROAMING - if(do_roaming) - if(WAVELAN_BEACON(skb->data)) - wl_roam_gather(dev, skb->data, stats); -#endif /* WAVELAN_ROAMING */ - -#ifdef WIRELESS_SPY - wl_spy_gather(dev, skb_mac_header(skb) + WAVELAN_ADDR_SIZE, stats); -#endif /* WIRELESS_SPY */ -#ifdef HISTOGRAM - wl_his_gather(dev, stats); -#endif /* HISTOGRAM */ - } - - /* - * Hand the packet to the Network Module - */ - netif_rx(skb); - - /* Keep stats up to date */ - dev->stats.rx_packets++; - dev->stats.rx_bytes += sksize; - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: <-wv_packet_read()\n", dev->name); -#endif - return; -} - -/*------------------------------------------------------------------*/ -/* - * This routine is called by the interrupt handler to initiate a - * packet transfer from the card to the network interface layer above - * this driver. This routine checks if a buffer has been successfully - * received by the WaveLAN card. If so, the routine wv_packet_read is - * called to do the actual transfer of the card's data including the - * ethernet header into a packet consisting of an sk_buff chain. - * (called by wavelan_interrupt()) - * Note : the spinlock is already grabbed for us and irq are disabled. - */ -static void -wv_packet_rcv(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - net_local * lp = netdev_priv(dev); - int newrfp; - int rp; - int len; - int f_start; - int status; - int i593_rfp; - int stat_ptr; - u_char c[4]; - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: ->wv_packet_rcv()\n", dev->name); -#endif - - /* Get the new receive frame pointer from the i82593 chip */ - outb(CR0_STATUS_2 | OP0_NOP, LCCR(base)); - i593_rfp = inb(LCSR(base)); - i593_rfp |= inb(LCSR(base)) << 8; - i593_rfp %= RX_SIZE; - - /* Get the new receive frame pointer from the WaveLAN card. - * It is 3 bytes more than the increment of the i82593 receive - * frame pointer, for each packet. This is because it includes the - * 3 roaming bytes added by the mmc. - */ - newrfp = inb(RPLL(base)); - newrfp |= inb(RPLH(base)) << 8; - newrfp %= RX_SIZE; - -#ifdef DEBUG_RX_INFO - printk(KERN_DEBUG "%s: wv_packet_rcv(): i593_rfp %d stop %d newrfp %d lp->rfp %d\n", - dev->name, i593_rfp, lp->stop, newrfp, lp->rfp); -#endif - -#ifdef DEBUG_RX_ERROR - /* If no new frame pointer... */ - if(lp->overrunning || newrfp == lp->rfp) - printk(KERN_INFO "%s: wv_packet_rcv(): no new frame: i593_rfp %d stop %d newrfp %d lp->rfp %d\n", - dev->name, i593_rfp, lp->stop, newrfp, lp->rfp); -#endif - - /* Read all frames (packets) received */ - while(newrfp != lp->rfp) - { - /* A frame is composed of the packet, followed by a status word, - * the length of the frame (word) and the mmc info (SNR & qual). - * It's because the length is at the end that we can only scan - * frames backward. */ - - /* Find the first frame by skipping backwards over the frames */ - rp = newrfp; /* End of last frame */ - while(((f_start = wv_start_of_frame(dev, rp, newrfp)) != lp->rfp) && - (f_start != -1)) - rp = f_start; - - /* If we had a problem */ - if(f_start == -1) - { -#ifdef DEBUG_RX_ERROR - printk(KERN_INFO "wavelan_cs: cannot find start of frame "); - printk(" i593_rfp %d stop %d newrfp %d lp->rfp %d\n", - i593_rfp, lp->stop, newrfp, lp->rfp); -#endif - lp->rfp = rp; /* Get to the last usable frame */ - continue; - } - - /* f_start point to the beggining of the first frame received - * and rp to the beggining of the next one */ - - /* Read status & length of the frame */ - stat_ptr = (rp - 7 + RX_SIZE) % RX_SIZE; - stat_ptr = read_ringbuf(dev, stat_ptr, c, 4); - status = c[0] | (c[1] << 8); - len = c[2] | (c[3] << 8); - - /* Check status */ - if((status & RX_RCV_OK) != RX_RCV_OK) - { - dev->stats.rx_errors++; - if(status & RX_NO_SFD) - dev->stats.rx_frame_errors++; - if(status & RX_CRC_ERR) - dev->stats.rx_crc_errors++; - if(status & RX_OVRRUN) - dev->stats.rx_over_errors++; - -#ifdef DEBUG_RX_FAIL - printk(KERN_DEBUG "%s: wv_packet_rcv(): packet not received ok, status = 0x%x\n", - dev->name, status); -#endif - } - else - /* Read the packet and transmit to Linux */ - wv_packet_read(dev, f_start, len - 2); - - /* One frame has been processed, skip it */ - lp->rfp = rp; - } - - /* - * Update the frame stop register, but set it to less than - * the full 8K to allow space for 3 bytes of signal strength - * per packet. - */ - lp->stop = (i593_rfp + RX_SIZE - ((RX_SIZE / 64) * 3)) % RX_SIZE; - outb(OP0_SWIT_TO_PORT_1 | CR0_CHNL, LCCR(base)); - outb(CR1_STOP_REG_UPDATE | (lp->stop >> RX_SIZE_SHIFT), LCCR(base)); - outb(OP1_SWIT_TO_PORT_0, LCCR(base)); - -#ifdef DEBUG_RX_TRACE - printk(KERN_DEBUG "%s: <-wv_packet_rcv()\n", dev->name); -#endif -} - -/*********************** PACKET TRANSMISSION ***********************/ -/* - * This part deal with sending packet through the wavelan - * We copy the packet to the send buffer and then issue the send - * command to the i82593. The result of this operation will be - * checked in wavelan_interrupt() - */ - -/*------------------------------------------------------------------*/ -/* - * This routine fills in the appropriate registers and memory - * locations on the WaveLAN card and starts the card off on - * the transmit. - * (called in wavelan_packet_xmit()) - */ -static void -wv_packet_write(struct net_device * dev, - void * buf, - short length) -{ - net_local * lp = netdev_priv(dev); - unsigned int base = dev->base_addr; - unsigned long flags; - int clen = length; - register u_short xmtdata_base = TX_BASE; - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: ->wv_packet_write(%d)\n", dev->name, length); -#endif - - spin_lock_irqsave(&lp->spinlock, flags); - - /* Write the length of data buffer followed by the buffer */ - outb(xmtdata_base & 0xff, PIORL(base)); - outb(((xmtdata_base >> 8) & PIORH_MASK) | PIORH_SEL_TX, PIORH(base)); - outb(clen & 0xff, PIOP(base)); /* lsb */ - outb(clen >> 8, PIOP(base)); /* msb */ - - /* Send the data */ - outsb(PIOP(base), buf, clen); - - /* Indicate end of transmit chain */ - outb(OP0_NOP, PIOP(base)); - /* josullvn@cs.cmu.edu: need to send a second NOP for alignment... */ - outb(OP0_NOP, PIOP(base)); - - /* Reset the transmit DMA pointer */ - hacr_write_slow(base, HACR_PWR_STAT | HACR_TX_DMA_RESET); - hacr_write(base, HACR_DEFAULT); - /* Send the transmit command */ - wv_82593_cmd(dev, "wv_packet_write(): transmit", - OP0_TRANSMIT, SR0_NO_RESULT); - - /* Make sure the watchdog will keep quiet for a while */ - dev->trans_start = jiffies; - - /* Keep stats up to date */ - dev->stats.tx_bytes += length; - - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_TX_INFO - wv_packet_info((u_char *) buf, length, dev->name, "wv_packet_write"); -#endif /* DEBUG_TX_INFO */ - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: <-wv_packet_write()\n", dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * This routine is called when we want to send a packet (NET3 callback) - * In this routine, we check if the harware is ready to accept - * the packet. We also prevent reentrance. Then, we call the function - * to send the packet... - */ -static netdev_tx_t -wavelan_packet_xmit(struct sk_buff * skb, - struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - unsigned long flags; - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: ->wavelan_packet_xmit(0x%X)\n", dev->name, - (unsigned) skb); -#endif - - /* - * Block a timer-based transmit from overlapping a previous transmit. - * In other words, prevent reentering this routine. - */ - netif_stop_queue(dev); - - /* If somebody has asked to reconfigure the controller, - * we can do it now */ - if(lp->reconfig_82593) - { - spin_lock_irqsave(&lp->spinlock, flags); /* Disable interrupts */ - wv_82593_config(dev); - spin_unlock_irqrestore(&lp->spinlock, flags); /* Re-enable interrupts */ - /* Note : the configure procedure was totally synchronous, - * so the Tx buffer is now free */ - } - - /* Check if we need some padding */ - /* Note : on wireless the propagation time is in the order of 1us, - * and we don't have the Ethernet specific requirement of beeing - * able to detect collisions, therefore in theory we don't really - * need to pad. Jean II */ - if (skb_padto(skb, ETH_ZLEN)) - return NETDEV_TX_OK; - - wv_packet_write(dev, skb->data, skb->len); - - dev_kfree_skb(skb); - -#ifdef DEBUG_TX_TRACE - printk(KERN_DEBUG "%s: <-wavelan_packet_xmit()\n", dev->name); -#endif - return NETDEV_TX_OK; -} - -/********************** HARDWARE CONFIGURATION **********************/ -/* - * This part do the real job of starting and configuring the hardware. - */ - -/*------------------------------------------------------------------*/ -/* - * Routine to initialize the Modem Management Controller. - * (called by wv_hw_config()) - */ -static int -wv_mmc_init(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - psa_t psa; - mmw_t m; - int configured; - int i; /* Loop counter */ - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_mmc_init()\n", dev->name); -#endif - - /* Read the parameter storage area */ - psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa)); - - /* - * Check the first three octets of the MAC addr for the manufacturer's code. - * Note: If you get the error message below, you've got a - * non-NCR/AT&T/Lucent PCMCIA cards, see wavelan_cs.h for detail on - * how to configure your card... - */ - for (i = 0; i < ARRAY_SIZE(MAC_ADDRESSES); i++) - if ((psa.psa_univ_mac_addr[0] == MAC_ADDRESSES[i][0]) && - (psa.psa_univ_mac_addr[1] == MAC_ADDRESSES[i][1]) && - (psa.psa_univ_mac_addr[2] == MAC_ADDRESSES[i][2])) - break; - - /* If we have not found it... */ - if (i == ARRAY_SIZE(MAC_ADDRESSES)) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_WARNING "%s: wv_mmc_init(): Invalid MAC address: %02X:%02X:%02X:...\n", - dev->name, psa.psa_univ_mac_addr[0], - psa.psa_univ_mac_addr[1], psa.psa_univ_mac_addr[2]); -#endif - return FALSE; - } - - /* Get the MAC address */ - memcpy(&dev->dev_addr[0], &psa.psa_univ_mac_addr[0], WAVELAN_ADDR_SIZE); - -#ifdef USE_PSA_CONFIG - configured = psa.psa_conf_status & 1; -#else - configured = 0; -#endif - - /* Is the PSA is not configured */ - if(!configured) - { - /* User will be able to configure NWID after (with iwconfig) */ - psa.psa_nwid[0] = 0; - psa.psa_nwid[1] = 0; - - /* As NWID is not set : no NWID checking */ - psa.psa_nwid_select = 0; - - /* Disable encryption */ - psa.psa_encryption_select = 0; - - /* Set to standard values - * 0x04 for AT, - * 0x01 for MCA, - * 0x04 for PCMCIA and 2.00 card (AT&T 407-024689/E document) - */ - if (psa.psa_comp_number & 1) - psa.psa_thr_pre_set = 0x01; - else - psa.psa_thr_pre_set = 0x04; - psa.psa_quality_thr = 0x03; - - /* It is configured */ - psa.psa_conf_status |= 1; - -#ifdef USE_PSA_CONFIG - /* Write the psa */ - psa_write(dev, (char *)psa.psa_nwid - (char *)&psa, - (unsigned char *)psa.psa_nwid, 4); - psa_write(dev, (char *)&psa.psa_thr_pre_set - (char *)&psa, - (unsigned char *)&psa.psa_thr_pre_set, 1); - psa_write(dev, (char *)&psa.psa_quality_thr - (char *)&psa, - (unsigned char *)&psa.psa_quality_thr, 1); - psa_write(dev, (char *)&psa.psa_conf_status - (char *)&psa, - (unsigned char *)&psa.psa_conf_status, 1); - /* update the Wavelan checksum */ - update_psa_checksum(dev); -#endif /* USE_PSA_CONFIG */ - } - - /* Zero the mmc structure */ - memset(&m, 0x00, sizeof(m)); - - /* Copy PSA info to the mmc */ - m.mmw_netw_id_l = psa.psa_nwid[1]; - m.mmw_netw_id_h = psa.psa_nwid[0]; - - if(psa.psa_nwid_select & 1) - m.mmw_loopt_sel = 0x00; - else - m.mmw_loopt_sel = MMW_LOOPT_SEL_DIS_NWID; - - memcpy(&m.mmw_encr_key, &psa.psa_encryption_key, - sizeof(m.mmw_encr_key)); - - if(psa.psa_encryption_select) - m.mmw_encr_enable = MMW_ENCR_ENABLE_EN | MMW_ENCR_ENABLE_MODE; - else - m.mmw_encr_enable = 0; - - m.mmw_thr_pre_set = psa.psa_thr_pre_set & 0x3F; - m.mmw_quality_thr = psa.psa_quality_thr & 0x0F; - - /* - * Set default modem control parameters. - * See NCR document 407-0024326 Rev. A. - */ - m.mmw_jabber_enable = 0x01; - m.mmw_anten_sel = MMW_ANTEN_SEL_ALG_EN; - m.mmw_ifs = 0x20; - m.mmw_mod_delay = 0x04; - m.mmw_jam_time = 0x38; - - m.mmw_des_io_invert = 0; - m.mmw_freeze = 0; - m.mmw_decay_prm = 0; - m.mmw_decay_updat_prm = 0; - - /* Write all info to mmc */ - mmc_write(base, 0, (u_char *)&m, sizeof(m)); - - /* The following code start the modem of the 2.00 frequency - * selectable cards at power on. It's not strictly needed for the - * following boots... - * The original patch was by Joe Finney for the PCMCIA driver, but - * I've cleaned it a bit and add documentation. - * Thanks to Loeke Brederveld from Lucent for the info. - */ - - /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable) - * (does it work for everybody ? - especially old cards...) */ - /* Note : WFREQSEL verify that it is able to read from EEprom - * a sensible frequency (address 0x00) + that MMR_FEE_STATUS_ID - * is 0xA (Xilinx version) or 0xB (Ariadne version). - * My test is more crude but do work... */ - if(!(mmc_in(base, mmroff(0, mmr_fee_status)) & - (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) - { - /* We must download the frequency parameters to the - * synthetisers (from the EEprom - area 1) - * Note : as the EEprom is auto decremented, we set the end - * if the area... */ - m.mmw_fee_addr = 0x0F; - m.mmw_fee_ctrl = MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD; - mmc_write(base, (char *)&m.mmw_fee_ctrl - (char *)&m, - (unsigned char *)&m.mmw_fee_ctrl, 2); - - /* Wait until the download is finished */ - fee_wait(base, 100, 100); - -#ifdef DEBUG_CONFIG_INFO - /* The frequency was in the last word downloaded... */ - mmc_read(base, (char *)&m.mmw_fee_data_l - (char *)&m, - (unsigned char *)&m.mmw_fee_data_l, 2); - - /* Print some info for the user */ - printk(KERN_DEBUG "%s: Wavelan 2.00 recognised (frequency select) : Current frequency = %ld\n", - dev->name, - ((m.mmw_fee_data_h << 4) | - (m.mmw_fee_data_l >> 4)) * 5 / 2 + 24000L); -#endif - - /* We must now download the power adjust value (gain) to - * the synthetisers (from the EEprom - area 7 - DAC) */ - m.mmw_fee_addr = 0x61; - m.mmw_fee_ctrl = MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD; - mmc_write(base, (char *)&m.mmw_fee_ctrl - (char *)&m, - (unsigned char *)&m.mmw_fee_ctrl, 2); - - /* Wait until the download is finished */ - } /* if 2.00 card */ - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_mmc_init()\n", dev->name); -#endif - return TRUE; -} - -/*------------------------------------------------------------------*/ -/* - * Routine to gracefully turn off reception, and wait for any commands - * to complete. - * (called in wv_ru_start() and wavelan_close() and wavelan_event()) - */ -static int -wv_ru_stop(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - net_local * lp = netdev_priv(dev); - unsigned long flags; - int status; - int spin; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_ru_stop()\n", dev->name); -#endif - - spin_lock_irqsave(&lp->spinlock, flags); - - /* First, send the LAN controller a stop receive command */ - wv_82593_cmd(dev, "wv_graceful_shutdown(): stop-rcv", - OP0_STOP_RCV, SR0_NO_RESULT); - - /* Then, spin until the receive unit goes idle */ - spin = 300; - do - { - udelay(10); - outb(OP0_NOP | CR0_STATUS_3, LCCR(base)); - status = inb(LCSR(base)); - } - while(((status & SR3_RCV_STATE_MASK) != SR3_RCV_IDLE) && (spin-- > 0)); - - /* Now, spin until the chip finishes executing its current command */ - do - { - udelay(10); - outb(OP0_NOP | CR0_STATUS_3, LCCR(base)); - status = inb(LCSR(base)); - } - while(((status & SR3_EXEC_STATE_MASK) != SR3_EXEC_IDLE) && (spin-- > 0)); - - spin_unlock_irqrestore(&lp->spinlock, flags); - - /* If there was a problem */ - if(spin <= 0) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_INFO "%s: wv_ru_stop(): The chip doesn't want to stop...\n", - dev->name); -#endif - return FALSE; - } - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_ru_stop()\n", dev->name); -#endif - return TRUE; -} /* wv_ru_stop */ - -/*------------------------------------------------------------------*/ -/* - * This routine starts the receive unit running. First, it checks if - * the card is actually ready. Then the card is instructed to receive - * packets again. - * (called in wv_hw_reset() & wavelan_open()) - */ -static int -wv_ru_start(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - net_local * lp = netdev_priv(dev); - unsigned long flags; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_ru_start()\n", dev->name); -#endif - - /* - * We need to start from a quiescent state. To do so, we could check - * if the card is already running, but instead we just try to shut - * it down. First, we disable reception (in case it was already enabled). - */ - if(!wv_ru_stop(dev)) - return FALSE; - - spin_lock_irqsave(&lp->spinlock, flags); - - /* Now we know that no command is being executed. */ - - /* Set the receive frame pointer and stop pointer */ - lp->rfp = 0; - outb(OP0_SWIT_TO_PORT_1 | CR0_CHNL, LCCR(base)); - - /* Reset ring management. This sets the receive frame pointer to 1 */ - outb(OP1_RESET_RING_MNGMT, LCCR(base)); - -#if 0 - /* XXX the i82593 manual page 6-4 seems to indicate that the stop register - should be set as below */ - /* outb(CR1_STOP_REG_UPDATE|((RX_SIZE - 0x40)>> RX_SIZE_SHIFT),LCCR(base));*/ -#elif 0 - /* but I set it 0 instead */ - lp->stop = 0; -#else - /* but I set it to 3 bytes per packet less than 8K */ - lp->stop = (0 + RX_SIZE - ((RX_SIZE / 64) * 3)) % RX_SIZE; -#endif - outb(CR1_STOP_REG_UPDATE | (lp->stop >> RX_SIZE_SHIFT), LCCR(base)); - outb(OP1_INT_ENABLE, LCCR(base)); - outb(OP1_SWIT_TO_PORT_0, LCCR(base)); - - /* Reset receive DMA pointer */ - hacr_write_slow(base, HACR_PWR_STAT | HACR_TX_DMA_RESET); - hacr_write_slow(base, HACR_DEFAULT); - - /* Receive DMA on channel 1 */ - wv_82593_cmd(dev, "wv_ru_start(): rcv-enable", - CR0_CHNL | OP0_RCV_ENABLE, SR0_NO_RESULT); - -#ifdef DEBUG_I82593_SHOW - { - int status; - int opri; - int spin = 10000; - - /* spin until the chip starts receiving */ - do - { - outb(OP0_NOP | CR0_STATUS_3, LCCR(base)); - status = inb(LCSR(base)); - if(spin-- <= 0) - break; - } - while(((status & SR3_RCV_STATE_MASK) != SR3_RCV_ACTIVE) && - ((status & SR3_RCV_STATE_MASK) != SR3_RCV_READY)); - printk(KERN_DEBUG "rcv status is 0x%x [i:%d]\n", - (status & SR3_RCV_STATE_MASK), i); - } -#endif - - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_ru_start()\n", dev->name); -#endif - return TRUE; -} - -/*------------------------------------------------------------------*/ -/* - * This routine does a standard config of the WaveLAN controller (i82593). - * In the ISA driver, this is integrated in wavelan_hardware_reset() - * (called by wv_hw_config(), wv_82593_reconfig() & wavelan_packet_xmit()) - */ -static int -wv_82593_config(struct net_device * dev) -{ - unsigned int base = dev->base_addr; - net_local * lp = netdev_priv(dev); - struct i82593_conf_block cfblk; - int ret = TRUE; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_82593_config()\n", dev->name); -#endif - - /* Create & fill i82593 config block - * - * Now conform to Wavelan document WCIN085B - */ - memset(&cfblk, 0x00, sizeof(struct i82593_conf_block)); - cfblk.d6mod = FALSE; /* Run in i82593 advanced mode */ - cfblk.fifo_limit = 5; /* = 56 B rx and 40 B tx fifo thresholds */ - cfblk.forgnesi = FALSE; /* 0=82C501, 1=AMD7992B compatibility */ - cfblk.fifo_32 = 1; - cfblk.throttle_enb = FALSE; - cfblk.contin = TRUE; /* enable continuous mode */ - cfblk.cntrxint = FALSE; /* enable continuous mode receive interrupts */ - cfblk.addr_len = WAVELAN_ADDR_SIZE; - cfblk.acloc = TRUE; /* Disable source addr insertion by i82593 */ - cfblk.preamb_len = 0; /* 2 bytes preamble (SFD) */ - cfblk.loopback = FALSE; - cfblk.lin_prio = 0; /* conform to 802.3 backoff algorithm */ - cfblk.exp_prio = 5; /* conform to 802.3 backoff algorithm */ - cfblk.bof_met = 1; /* conform to 802.3 backoff algorithm */ - cfblk.ifrm_spc = 0x20 >> 4; /* 32 bit times interframe spacing */ - cfblk.slottim_low = 0x20 >> 5; /* 32 bit times slot time */ - cfblk.slottim_hi = 0x0; - cfblk.max_retr = 15; - cfblk.prmisc = ((lp->promiscuous) ? TRUE: FALSE); /* Promiscuous mode */ - cfblk.bc_dis = FALSE; /* Enable broadcast reception */ - cfblk.crs_1 = TRUE; /* Transmit without carrier sense */ - cfblk.nocrc_ins = FALSE; /* i82593 generates CRC */ - cfblk.crc_1632 = FALSE; /* 32-bit Autodin-II CRC */ - cfblk.crs_cdt = FALSE; /* CD not to be interpreted as CS */ - cfblk.cs_filter = 0; /* CS is recognized immediately */ - cfblk.crs_src = FALSE; /* External carrier sense */ - cfblk.cd_filter = 0; /* CD is recognized immediately */ - cfblk.min_fr_len = ETH_ZLEN >> 2; /* Minimum frame length 64 bytes */ - cfblk.lng_typ = FALSE; /* Length field > 1500 = type field */ - cfblk.lng_fld = TRUE; /* Disable 802.3 length field check */ - cfblk.rxcrc_xf = TRUE; /* Don't transfer CRC to memory */ - cfblk.artx = TRUE; /* Disable automatic retransmission */ - cfblk.sarec = TRUE; /* Disable source addr trig of CD */ - cfblk.tx_jabber = TRUE; /* Disable jabber jam sequence */ - cfblk.hash_1 = FALSE; /* Use bits 0-5 in mc address hash */ - cfblk.lbpkpol = TRUE; /* Loopback pin active high */ - cfblk.fdx = FALSE; /* Disable full duplex operation */ - cfblk.dummy_6 = 0x3f; /* all ones */ - cfblk.mult_ia = FALSE; /* No multiple individual addresses */ - cfblk.dis_bof = FALSE; /* Disable the backoff algorithm ?! */ - cfblk.dummy_1 = TRUE; /* set to 1 */ - cfblk.tx_ifs_retrig = 3; /* Hmm... Disabled */ -#ifdef MULTICAST_ALL - cfblk.mc_all = (lp->allmulticast ? TRUE: FALSE); /* Allow all multicasts */ -#else - cfblk.mc_all = FALSE; /* No multicast all mode */ -#endif - cfblk.rcv_mon = 0; /* Monitor mode disabled */ - cfblk.frag_acpt = TRUE; /* Do not accept fragments */ - cfblk.tstrttrs = FALSE; /* No start transmission threshold */ - cfblk.fretx = TRUE; /* FIFO automatic retransmission */ - cfblk.syncrqs = FALSE; /* Synchronous DRQ deassertion... */ - cfblk.sttlen = TRUE; /* 6 byte status registers */ - cfblk.rx_eop = TRUE; /* Signal EOP on packet reception */ - cfblk.tx_eop = TRUE; /* Signal EOP on packet transmission */ - cfblk.rbuf_size = RX_SIZE>>11; /* Set receive buffer size */ - cfblk.rcvstop = TRUE; /* Enable Receive Stop Register */ - -#ifdef DEBUG_I82593_SHOW - print_hex_dump(KERN_DEBUG, "wavelan_cs: config block: ", DUMP_PREFIX_NONE, - 16, 1, &cfblk, sizeof(struct i82593_conf_block), false); -#endif - - /* Copy the config block to the i82593 */ - outb(TX_BASE & 0xff, PIORL(base)); - outb(((TX_BASE >> 8) & PIORH_MASK) | PIORH_SEL_TX, PIORH(base)); - outb(sizeof(struct i82593_conf_block) & 0xff, PIOP(base)); /* lsb */ - outb(sizeof(struct i82593_conf_block) >> 8, PIOP(base)); /* msb */ - outsb(PIOP(base), (char *) &cfblk, sizeof(struct i82593_conf_block)); - - /* reset transmit DMA pointer */ - hacr_write_slow(base, HACR_PWR_STAT | HACR_TX_DMA_RESET); - hacr_write(base, HACR_DEFAULT); - if(!wv_82593_cmd(dev, "wv_82593_config(): configure", - OP0_CONFIGURE, SR0_CONFIGURE_DONE)) - ret = FALSE; - - /* Initialize adapter's ethernet MAC address */ - outb(TX_BASE & 0xff, PIORL(base)); - outb(((TX_BASE >> 8) & PIORH_MASK) | PIORH_SEL_TX, PIORH(base)); - outb(WAVELAN_ADDR_SIZE, PIOP(base)); /* byte count lsb */ - outb(0, PIOP(base)); /* byte count msb */ - outsb(PIOP(base), &dev->dev_addr[0], WAVELAN_ADDR_SIZE); - - /* reset transmit DMA pointer */ - hacr_write_slow(base, HACR_PWR_STAT | HACR_TX_DMA_RESET); - hacr_write(base, HACR_DEFAULT); - if(!wv_82593_cmd(dev, "wv_82593_config(): ia-setup", - OP0_IA_SETUP, SR0_IA_SETUP_DONE)) - ret = FALSE; - -#ifdef WAVELAN_ROAMING - /* If roaming is enabled, join the "Beacon Request" multicast group... */ - /* But only if it's not in there already! */ - if(do_roaming) - dev_mc_add(dev,WAVELAN_BEACON_ADDRESS, WAVELAN_ADDR_SIZE, 1); -#endif /* WAVELAN_ROAMING */ - - /* If any multicast address to set */ - if(lp->mc_count) - { - struct dev_mc_list * dmi; - int addrs_len = WAVELAN_ADDR_SIZE * lp->mc_count; - -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG "%s: wv_hw_config(): set %d multicast addresses:\n", - dev->name, lp->mc_count); - for(dmi=dev->mc_list; dmi; dmi=dmi->next) - printk(KERN_DEBUG " %pM\n", dmi->dmi_addr); -#endif - - /* Initialize adapter's ethernet multicast addresses */ - outb(TX_BASE & 0xff, PIORL(base)); - outb(((TX_BASE >> 8) & PIORH_MASK) | PIORH_SEL_TX, PIORH(base)); - outb(addrs_len & 0xff, PIOP(base)); /* byte count lsb */ - outb((addrs_len >> 8), PIOP(base)); /* byte count msb */ - for(dmi=dev->mc_list; dmi; dmi=dmi->next) - outsb(PIOP(base), dmi->dmi_addr, dmi->dmi_addrlen); - - /* reset transmit DMA pointer */ - hacr_write_slow(base, HACR_PWR_STAT | HACR_TX_DMA_RESET); - hacr_write(base, HACR_DEFAULT); - if(!wv_82593_cmd(dev, "wv_82593_config(): mc-setup", - OP0_MC_SETUP, SR0_MC_SETUP_DONE)) - ret = FALSE; - lp->mc_count = dev->mc_count; /* remember to avoid repeated reset */ - } - - /* Job done, clear the flag */ - lp->reconfig_82593 = FALSE; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_82593_config()\n", dev->name); -#endif - return(ret); -} - -/*------------------------------------------------------------------*/ -/* - * Read the Access Configuration Register, perform a software reset, - * and then re-enable the card's software. - * - * If I understand correctly : reset the pcmcia interface of the - * wavelan. - * (called by wv_config()) - */ -static int -wv_pcmcia_reset(struct net_device * dev) -{ - int i; - conf_reg_t reg = { 0, CS_READ, CISREG_COR, 0 }; - struct pcmcia_device * link = ((net_local *)netdev_priv(dev))->link; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_pcmcia_reset()\n", dev->name); -#endif - - i = pcmcia_access_configuration_register(link, ®); - if (i != 0) - { - cs_error(link, AccessConfigurationRegister, i); - return FALSE; - } - -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG "%s: wavelan_pcmcia_reset(): Config reg is 0x%x\n", - dev->name, (u_int) reg.Value); -#endif - - reg.Action = CS_WRITE; - reg.Value = reg.Value | COR_SW_RESET; - i = pcmcia_access_configuration_register(link, ®); - if (i != 0) - { - cs_error(link, AccessConfigurationRegister, i); - return FALSE; - } - - reg.Action = CS_WRITE; - reg.Value = COR_LEVEL_IRQ | COR_CONFIG; - i = pcmcia_access_configuration_register(link, ®); - if (i != 0) - { - cs_error(link, AccessConfigurationRegister, i); - return FALSE; - } - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_pcmcia_reset()\n", dev->name); -#endif - return TRUE; -} - -/*------------------------------------------------------------------*/ -/* - * wavelan_hw_config() is called after a CARD_INSERTION event is - * received, to configure the wavelan hardware. - * Note that the reception will be enabled in wavelan->open(), so the - * device is configured but idle... - * Performs the following actions: - * 1. A pcmcia software reset (using wv_pcmcia_reset()) - * 2. A power reset (reset DMA) - * 3. Reset the LAN controller - * 4. Initialize the radio modem (using wv_mmc_init) - * 5. Configure LAN controller (using wv_82593_config) - * 6. Perform a diagnostic on the LAN controller - * (called by wavelan_event() & wv_hw_reset()) - */ -static int -wv_hw_config(struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - unsigned int base = dev->base_addr; - unsigned long flags; - int ret = FALSE; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_hw_config()\n", dev->name); -#endif - - /* compile-time check the sizes of structures */ - BUILD_BUG_ON(sizeof(psa_t) != PSA_SIZE); - BUILD_BUG_ON(sizeof(mmw_t) != MMW_SIZE); - BUILD_BUG_ON(sizeof(mmr_t) != MMR_SIZE); - - /* Reset the pcmcia interface */ - if(wv_pcmcia_reset(dev) == FALSE) - return FALSE; - - /* Disable interrupts */ - spin_lock_irqsave(&lp->spinlock, flags); - - /* Disguised goto ;-) */ - do - { - /* Power UP the module + reset the modem + reset host adapter - * (in fact, reset DMA channels) */ - hacr_write_slow(base, HACR_RESET); - hacr_write(base, HACR_DEFAULT); - - /* Check if the module has been powered up... */ - if(hasr_read(base) & HASR_NO_CLK) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_WARNING "%s: wv_hw_config(): modem not connected or not a wavelan card\n", - dev->name); -#endif - break; - } - - /* initialize the modem */ - if(wv_mmc_init(dev) == FALSE) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_WARNING "%s: wv_hw_config(): Can't configure the modem\n", - dev->name); -#endif - break; - } - - /* reset the LAN controller (i82593) */ - outb(OP0_RESET, LCCR(base)); - mdelay(1); /* A bit crude ! */ - - /* Initialize the LAN controller */ - if(wv_82593_config(dev) == FALSE) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_INFO "%s: wv_hw_config(): i82593 init failed\n", - dev->name); -#endif - break; - } - - /* Diagnostic */ - if(wv_diag(dev) == FALSE) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_INFO "%s: wv_hw_config(): i82593 diagnostic failed\n", - dev->name); -#endif - break; - } - - /* - * insert code for loopback test here - */ - - /* The device is now configured */ - lp->configured = 1; - ret = TRUE; - } - while(0); - - /* Re-enable interrupts */ - spin_unlock_irqrestore(&lp->spinlock, flags); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_hw_config()\n", dev->name); -#endif - return(ret); -} - -/*------------------------------------------------------------------*/ -/* - * Totally reset the wavelan and restart it. - * Performs the following actions: - * 1. Call wv_hw_config() - * 2. Start the LAN controller's receive unit - * (called by wavelan_event(), wavelan_watchdog() and wavelan_open()) - */ -static void -wv_hw_reset(struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: ->wv_hw_reset()\n", dev->name); -#endif - - lp->nresets++; - lp->configured = 0; - - /* Call wv_hw_config() for most of the reset & init stuff */ - if(wv_hw_config(dev) == FALSE) - return; - - /* start receive unit */ - wv_ru_start(dev); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <-wv_hw_reset()\n", dev->name); -#endif -} - -/*------------------------------------------------------------------*/ -/* - * wv_pcmcia_config() is called after a CARD_INSERTION event is - * received, to configure the PCMCIA socket, and to make the ethernet - * device available to the system. - * (called by wavelan_event()) - */ -static int -wv_pcmcia_config(struct pcmcia_device * link) -{ - struct net_device * dev = (struct net_device *) link->priv; - int i; - win_req_t req; - memreq_t mem; - net_local * lp = netdev_priv(dev); - - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "->wv_pcmcia_config(0x%p)\n", link); -#endif - - do - { - i = pcmcia_request_io(link, &link->io); - if (i != 0) - { - cs_error(link, RequestIO, i); - break; - } - - /* - * Now allocate an interrupt line. Note that this does not - * actually assign a handler to the interrupt. - */ - i = pcmcia_request_irq(link, &link->irq); - if (i != 0) - { - cs_error(link, RequestIRQ, i); - break; - } - - /* - * This actually configures the PCMCIA socket -- setting up - * the I/O windows and the interrupt mapping. - */ - link->conf.ConfigIndex = 1; - i = pcmcia_request_configuration(link, &link->conf); - if (i != 0) - { - cs_error(link, RequestConfiguration, i); - break; - } - - /* - * Allocate a small memory window. Note that the struct pcmcia_device - * structure provides space for one window handle -- if your - * device needs several windows, you'll need to keep track of - * the handles in your private data structure, link->priv. - */ - req.Attributes = WIN_DATA_WIDTH_8|WIN_MEMORY_TYPE_AM|WIN_ENABLE; - req.Base = req.Size = 0; - req.AccessSpeed = mem_speed; - i = pcmcia_request_window(&link, &req, &link->win); - if (i != 0) - { - cs_error(link, RequestWindow, i); - break; - } - - lp->mem = ioremap(req.Base, req.Size); - dev->mem_start = (u_long)lp->mem; - dev->mem_end = dev->mem_start + req.Size; - - mem.CardOffset = 0; mem.Page = 0; - i = pcmcia_map_mem_page(link->win, &mem); - if (i != 0) - { - cs_error(link, MapMemPage, i); - break; - } - - /* Feed device with this info... */ - dev->irq = link->irq.AssignedIRQ; - dev->base_addr = link->io.BasePort1; - netif_start_queue(dev); - -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG "wv_pcmcia_config: MEMSTART %p IRQ %d IOPORT 0x%x\n", - lp->mem, dev->irq, (u_int) dev->base_addr); -#endif - - SET_NETDEV_DEV(dev, &handle_to_dev(link)); - i = register_netdev(dev); - if(i != 0) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_INFO "wv_pcmcia_config(): register_netdev() failed\n"); -#endif - break; - } - } - while(0); /* Humm... Disguised goto !!! */ - - /* If any step failed, release any partially configured state */ - if(i != 0) - { - wv_pcmcia_release(link); - return FALSE; - } - - strcpy(((net_local *) netdev_priv(dev))->node.dev_name, dev->name); - link->dev_node = &((net_local *) netdev_priv(dev))->node; - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "<-wv_pcmcia_config()\n"); -#endif - return TRUE; -} - -/*------------------------------------------------------------------*/ -/* - * After a card is removed, wv_pcmcia_release() will unregister the net - * device, and release the PCMCIA configuration. If the device is - * still open, this will be postponed until it is closed. - */ -static void -wv_pcmcia_release(struct pcmcia_device *link) -{ - struct net_device * dev = (struct net_device *) link->priv; - net_local * lp = netdev_priv(dev); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: -> wv_pcmcia_release(0x%p)\n", dev->name, link); -#endif - - iounmap(lp->mem); - pcmcia_disable_device(link); - -#ifdef DEBUG_CONFIG_TRACE - printk(KERN_DEBUG "%s: <- wv_pcmcia_release()\n", dev->name); -#endif -} - -/************************ INTERRUPT HANDLING ************************/ - -/* - * This function is the interrupt handler for the WaveLAN card. This - * routine will be called whenever: - * 1. A packet is received. - * 2. A packet has successfully been transferred and the unit is - * ready to transmit another packet. - * 3. A command has completed execution. - */ -static irqreturn_t -wavelan_interrupt(int irq, - void * dev_id) -{ - struct net_device * dev = dev_id; - net_local * lp; - unsigned int base; - int status0; - u_int tx_status; - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: ->wavelan_interrupt()\n", dev->name); -#endif - - lp = netdev_priv(dev); - base = dev->base_addr; - -#ifdef DEBUG_INTERRUPT_INFO - /* Check state of our spinlock (it should be cleared) */ - if(spin_is_locked(&lp->spinlock)) - printk(KERN_DEBUG - "%s: wavelan_interrupt(): spinlock is already locked !!!\n", - dev->name); -#endif - - /* Prevent reentrancy. We need to do that because we may have - * multiple interrupt handler running concurently. - * It is safe because interrupts are disabled before aquiring - * the spinlock. */ - spin_lock(&lp->spinlock); - - /* Treat all pending interrupts */ - while(1) - { - /* ---------------- INTERRUPT CHECKING ---------------- */ - /* - * Look for the interrupt and verify the validity - */ - outb(CR0_STATUS_0 | OP0_NOP, LCCR(base)); - status0 = inb(LCSR(base)); - -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG "status0 0x%x [%s => 0x%x]", status0, - (status0&SR0_INTERRUPT)?"int":"no int",status0&~SR0_INTERRUPT); - if(status0&SR0_INTERRUPT) - { - printk(" [%s => %d]\n", (status0 & SR0_CHNL) ? "chnl" : - ((status0 & SR0_EXECUTION) ? "cmd" : - ((status0 & SR0_RECEPTION) ? "recv" : "unknown")), - (status0 & SR0_EVENT_MASK)); - } - else - printk("\n"); -#endif - - /* Return if no actual interrupt from i82593 (normal exit) */ - if(!(status0 & SR0_INTERRUPT)) - break; - - /* If interrupt is both Rx and Tx or none... - * This code in fact is there to catch the spurious interrupt - * when you remove the wavelan pcmcia card from the socket */ - if(((status0 & SR0_BOTH_RX_TX) == SR0_BOTH_RX_TX) || - ((status0 & SR0_BOTH_RX_TX) == 0x0)) - { -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_INFO "%s: wv_interrupt(): bogus interrupt (or from dead card) : %X\n", - dev->name, status0); -#endif - /* Acknowledge the interrupt */ - outb(CR0_INT_ACK | OP0_NOP, LCCR(base)); - break; - } - - /* ----------------- RECEIVING PACKET ----------------- */ - /* - * When the wavelan signal the reception of a new packet, - * we call wv_packet_rcv() to copy if from the buffer and - * send it to NET3 - */ - if(status0 & SR0_RECEPTION) - { -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG "%s: wv_interrupt(): receive\n", dev->name); -#endif - - if((status0 & SR0_EVENT_MASK) == SR0_STOP_REG_HIT) - { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "%s: wv_interrupt(): receive buffer overflow\n", - dev->name); -#endif - dev->stats.rx_over_errors++; - lp->overrunning = 1; - } - - /* Get the packet */ - wv_packet_rcv(dev); - lp->overrunning = 0; - - /* Acknowledge the interrupt */ - outb(CR0_INT_ACK | OP0_NOP, LCCR(base)); - continue; - } - - /* ---------------- COMMAND COMPLETION ---------------- */ - /* - * Interrupts issued when the i82593 has completed a command. - * Most likely : transmission done - */ - - /* If a transmission has been done */ - if((status0 & SR0_EVENT_MASK) == SR0_TRANSMIT_DONE || - (status0 & SR0_EVENT_MASK) == SR0_RETRANSMIT_DONE || - (status0 & SR0_EVENT_MASK) == SR0_TRANSMIT_NO_CRC_DONE) - { -#ifdef DEBUG_TX_ERROR - if((status0 & SR0_EVENT_MASK) == SR0_TRANSMIT_NO_CRC_DONE) - printk(KERN_INFO "%s: wv_interrupt(): packet transmitted without CRC.\n", - dev->name); -#endif - - /* Get transmission status */ - tx_status = inb(LCSR(base)); - tx_status |= (inb(LCSR(base)) << 8); -#ifdef DEBUG_INTERRUPT_INFO - printk(KERN_DEBUG "%s: wv_interrupt(): transmission done\n", - dev->name); - { - u_int rcv_bytes; - u_char status3; - rcv_bytes = inb(LCSR(base)); - rcv_bytes |= (inb(LCSR(base)) << 8); - status3 = inb(LCSR(base)); - printk(KERN_DEBUG "tx_status 0x%02x rcv_bytes 0x%02x status3 0x%x\n", - tx_status, rcv_bytes, (u_int) status3); - } -#endif - /* Check for possible errors */ - if((tx_status & TX_OK) != TX_OK) - { - dev->stats.tx_errors++; - - if(tx_status & TX_FRTL) - { -#ifdef DEBUG_TX_ERROR - printk(KERN_INFO "%s: wv_interrupt(): frame too long\n", - dev->name); -#endif - } - if(tx_status & TX_UND_RUN) - { -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG "%s: wv_interrupt(): DMA underrun\n", - dev->name); -#endif - dev->stats.tx_aborted_errors++; - } - if(tx_status & TX_LOST_CTS) - { -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG "%s: wv_interrupt(): no CTS\n", dev->name); -#endif - dev->stats.tx_carrier_errors++; - } - if(tx_status & TX_LOST_CRS) - { -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG "%s: wv_interrupt(): no carrier\n", - dev->name); -#endif - dev->stats.tx_carrier_errors++; - } - if(tx_status & TX_HRT_BEAT) - { -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG "%s: wv_interrupt(): heart beat\n", dev->name); -#endif - dev->stats.tx_heartbeat_errors++; - } - if(tx_status & TX_DEFER) - { -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG "%s: wv_interrupt(): channel jammed\n", - dev->name); -#endif - } - /* Ignore late collisions since they're more likely to happen - * here (the WaveLAN design prevents the LAN controller from - * receiving while it is transmitting). We take action only when - * the maximum retransmit attempts is exceeded. - */ - if(tx_status & TX_COLL) - { - if(tx_status & TX_MAX_COL) - { -#ifdef DEBUG_TX_FAIL - printk(KERN_DEBUG "%s: wv_interrupt(): channel congestion\n", - dev->name); -#endif - if(!(tx_status & TX_NCOL_MASK)) - { - dev->stats.collisions += 0x10; - } - } - } - } /* if(!(tx_status & TX_OK)) */ - - dev->stats.collisions += (tx_status & TX_NCOL_MASK); - dev->stats.tx_packets++; - - netif_wake_queue(dev); - outb(CR0_INT_ACK | OP0_NOP, LCCR(base)); /* Acknowledge the interrupt */ - } - else /* if interrupt = transmit done or retransmit done */ - { -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "wavelan_cs: unknown interrupt, status0 = %02x\n", - status0); -#endif - outb(CR0_INT_ACK | OP0_NOP, LCCR(base)); /* Acknowledge the interrupt */ - } - } /* while(1) */ - - spin_unlock(&lp->spinlock); - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: <-wavelan_interrupt()\n", dev->name); -#endif - - /* We always return IRQ_HANDLED, because we will receive empty - * interrupts under normal operations. Anyway, it doesn't matter - * as we are dealing with an ISA interrupt that can't be shared. - * - * Explanation : under heavy receive, the following happens : - * ->wavelan_interrupt() - * (status0 & SR0_INTERRUPT) != 0 - * ->wv_packet_rcv() - * (status0 & SR0_INTERRUPT) != 0 - * ->wv_packet_rcv() - * (status0 & SR0_INTERRUPT) == 0 // i.e. no more event - * <-wavelan_interrupt() - * ->wavelan_interrupt() - * (status0 & SR0_INTERRUPT) == 0 // i.e. empty interrupt - * <-wavelan_interrupt() - * Jean II */ - return IRQ_HANDLED; -} /* wv_interrupt */ - -/*------------------------------------------------------------------*/ -/* - * Watchdog: when we start a transmission, a timer is set for us in the - * kernel. If the transmission completes, this timer is disabled. If - * the timer expires, we are called and we try to unlock the hardware. - * - * Note : This watchdog is move clever than the one in the ISA driver, - * because it try to abort the current command before reseting - * everything... - * On the other hand, it's a bit simpler, because we don't have to - * deal with the multiple Tx buffers... - */ -static void -wavelan_watchdog(struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - unsigned int base = dev->base_addr; - unsigned long flags; - int aborted = FALSE; - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: ->wavelan_watchdog()\n", dev->name); -#endif - -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "%s: wavelan_watchdog: watchdog timer expired\n", - dev->name); -#endif - - spin_lock_irqsave(&lp->spinlock, flags); - - /* Ask to abort the current command */ - outb(OP0_ABORT, LCCR(base)); - - /* Wait for the end of the command (a bit hackish) */ - if(wv_82593_cmd(dev, "wavelan_watchdog(): abort", - OP0_NOP | CR0_STATUS_3, SR0_EXECUTION_ABORTED)) - aborted = TRUE; - - /* Release spinlock here so that wv_hw_reset() can grab it */ - spin_unlock_irqrestore(&lp->spinlock, flags); - - /* Check if we were successful in aborting it */ - if(!aborted) - { - /* It seem that it wasn't enough */ -#ifdef DEBUG_INTERRUPT_ERROR - printk(KERN_INFO "%s: wavelan_watchdog: abort failed, trying reset\n", - dev->name); -#endif - wv_hw_reset(dev); - } - -#ifdef DEBUG_PSA_SHOW - { - psa_t psa; - psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa)); - wv_psa_show(&psa); - } -#endif -#ifdef DEBUG_MMC_SHOW - wv_mmc_show(dev); -#endif -#ifdef DEBUG_I82593_SHOW - wv_ru_show(dev); -#endif - - /* We are no more waiting for something... */ - netif_wake_queue(dev); - -#ifdef DEBUG_INTERRUPT_TRACE - printk(KERN_DEBUG "%s: <-wavelan_watchdog()\n", dev->name); -#endif -} - -/********************* CONFIGURATION CALLBACKS *********************/ -/* - * Here are the functions called by the pcmcia package (cardmgr) and - * linux networking (NET3) for initialization, configuration and - * deinstallations of the Wavelan Pcmcia Hardware. - */ - -/*------------------------------------------------------------------*/ -/* - * Configure and start up the WaveLAN PCMCIA adaptor. - * Called by NET3 when it "open" the device. - */ -static int -wavelan_open(struct net_device * dev) -{ - net_local * lp = netdev_priv(dev); - struct pcmcia_device * link = lp->link; - unsigned int base = dev->base_addr; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: ->wavelan_open(dev=0x%x)\n", dev->name, - (unsigned int) dev); -#endif - - /* Check if the modem is powered up (wavelan_close() power it down */ - if(hasr_read(base) & HASR_NO_CLK) - { - /* Power up (power up time is 250us) */ - hacr_write(base, HACR_DEFAULT); - - /* Check if the module has been powered up... */ - if(hasr_read(base) & HASR_NO_CLK) - { -#ifdef DEBUG_CONFIG_ERRORS - printk(KERN_WARNING "%s: wavelan_open(): modem not connected\n", - dev->name); -#endif - return FALSE; - } - } - - /* Start reception and declare the driver ready */ - if(!lp->configured) - return FALSE; - if(!wv_ru_start(dev)) - wv_hw_reset(dev); /* If problem : reset */ - netif_start_queue(dev); - - /* Mark the device as used */ - link->open++; - -#ifdef WAVELAN_ROAMING - if(do_roaming) - wv_roam_init(dev); -#endif /* WAVELAN_ROAMING */ - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: <-wavelan_open()\n", dev->name); -#endif - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * Shutdown the WaveLAN PCMCIA adaptor. - * Called by NET3 when it "close" the device. - */ -static int -wavelan_close(struct net_device * dev) -{ - struct pcmcia_device * link = ((net_local *)netdev_priv(dev))->link; - unsigned int base = dev->base_addr; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: ->wavelan_close(dev=0x%x)\n", dev->name, - (unsigned int) dev); -#endif - - /* If the device isn't open, then nothing to do */ - if(!link->open) - { -#ifdef DEBUG_CONFIG_INFO - printk(KERN_DEBUG "%s: wavelan_close(): device not open\n", dev->name); -#endif - return 0; - } - -#ifdef WAVELAN_ROAMING - /* Cleanup of roaming stuff... */ - if(do_roaming) - wv_roam_cleanup(dev); -#endif /* WAVELAN_ROAMING */ - - link->open--; - - /* If the card is still present */ - if(netif_running(dev)) - { - netif_stop_queue(dev); - - /* Stop receiving new messages and wait end of transmission */ - wv_ru_stop(dev); - - /* Power down the module */ - hacr_write(base, HACR_DEFAULT & (~HACR_PWR_STAT)); - } - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "%s: <-wavelan_close()\n", dev->name); -#endif - return 0; -} - -static const struct net_device_ops wavelan_netdev_ops = { - .ndo_open = wavelan_open, - .ndo_stop = wavelan_close, - .ndo_start_xmit = wavelan_packet_xmit, - .ndo_set_multicast_list = wavelan_set_multicast_list, -#ifdef SET_MAC_ADDRESS - .ndo_set_mac_address = wavelan_set_mac_address, -#endif - .ndo_tx_timeout = wavelan_watchdog, - .ndo_change_mtu = eth_change_mtu, - .ndo_validate_addr = eth_validate_addr, -}; - -/*------------------------------------------------------------------*/ -/* - * wavelan_attach() creates an "instance" of the driver, allocating - * local data structures for one device (one interface). The device - * is registered with Card Services. - * - * The dev_link structure is initialized, but we don't actually - * configure the card at this point -- we wait until we receive a - * card insertion event. - */ -static int -wavelan_probe(struct pcmcia_device *p_dev) -{ - struct net_device * dev; /* Interface generic data */ - net_local * lp; /* Interface specific data */ - int ret; - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "-> wavelan_attach()\n"); -#endif - - /* The io structure describes IO port mapping */ - p_dev->io.NumPorts1 = 8; - p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; - p_dev->io.IOAddrLines = 3; - - /* Interrupt setup */ - p_dev->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING | IRQ_HANDLE_PRESENT; - p_dev->irq.IRQInfo1 = IRQ_LEVEL_ID; - p_dev->irq.Handler = wavelan_interrupt; - - /* General socket configuration */ - p_dev->conf.Attributes = CONF_ENABLE_IRQ; - p_dev->conf.IntType = INT_MEMORY_AND_IO; - - /* Allocate the generic data structure */ - dev = alloc_etherdev(sizeof(net_local)); - if (!dev) - return -ENOMEM; - - p_dev->priv = p_dev->irq.Instance = dev; - - lp = netdev_priv(dev); - - /* Init specific data */ - lp->configured = 0; - lp->reconfig_82593 = FALSE; - lp->nresets = 0; - /* Multicast stuff */ - lp->promiscuous = 0; - lp->allmulticast = 0; - lp->mc_count = 0; - - /* Init spinlock */ - spin_lock_init(&lp->spinlock); - - /* back links */ - lp->dev = dev; - - /* wavelan NET3 callbacks */ - dev->netdev_ops = &wavelan_netdev_ops; - dev->watchdog_timeo = WATCHDOG_JIFFIES; - SET_ETHTOOL_OPS(dev, &ops); - - dev->wireless_handlers = &wavelan_handler_def; - lp->wireless_data.spy_data = &lp->spy_data; - dev->wireless_data = &lp->wireless_data; - - /* Other specific data */ - dev->mtu = WAVELAN_MTU; - - ret = wv_pcmcia_config(p_dev); - if (ret) - return ret; - - ret = wv_hw_config(dev); - if (ret) { - dev->irq = 0; - pcmcia_disable_device(p_dev); - return ret; - } - - wv_init_info(dev); - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "<- wavelan_attach()\n"); -#endif - - return 0; -} - -/*------------------------------------------------------------------*/ -/* - * This deletes a driver "instance". The device is de-registered with - * Card Services. If it has been released, all local data structures - * are freed. Otherwise, the structures will be freed when the device - * is released. - */ -static void -wavelan_detach(struct pcmcia_device *link) -{ -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "-> wavelan_detach(0x%p)\n", link); -#endif - - /* Some others haven't done their job : give them another chance */ - wv_pcmcia_release(link); - - /* Free pieces */ - if(link->priv) - { - struct net_device * dev = (struct net_device *) link->priv; - - /* Remove ourselves from the kernel list of ethernet devices */ - /* Warning : can't be called from interrupt, timer or wavelan_close() */ - if (link->dev_node) - unregister_netdev(dev); - link->dev_node = NULL; - ((net_local *)netdev_priv(dev))->link = NULL; - ((net_local *)netdev_priv(dev))->dev = NULL; - free_netdev(dev); - } - -#ifdef DEBUG_CALLBACK_TRACE - printk(KERN_DEBUG "<- wavelan_detach()\n"); -#endif -} - -static int wavelan_suspend(struct pcmcia_device *link) -{ - struct net_device * dev = (struct net_device *) link->priv; - - /* NB: wavelan_close will be called, but too late, so we are - * obliged to close nicely the wavelan here. David, could you - * close the device before suspending them ? And, by the way, - * could you, on resume, add a "route add -net ..." after the - * ifconfig up ? Thanks... */ - - /* Stop receiving new messages and wait end of transmission */ - wv_ru_stop(dev); - - if (link->open) - netif_device_detach(dev); - - /* Power down the module */ - hacr_write(dev->base_addr, HACR_DEFAULT & (~HACR_PWR_STAT)); - - return 0; -} - -static int wavelan_resume(struct pcmcia_device *link) -{ - struct net_device * dev = (struct net_device *) link->priv; - - if (link->open) { - wv_hw_reset(dev); - netif_device_attach(dev); - } - - return 0; -} - - -static struct pcmcia_device_id wavelan_ids[] = { - PCMCIA_DEVICE_PROD_ID12("AT&T","WaveLAN/PCMCIA", 0xe7c5affd, 0x1bc50975), - PCMCIA_DEVICE_PROD_ID12("Digital", "RoamAbout/DS", 0x9999ab35, 0x00d05e06), - PCMCIA_DEVICE_PROD_ID12("Lucent Technologies", "WaveLAN/PCMCIA", 0x23eb9949, 0x1bc50975), - PCMCIA_DEVICE_PROD_ID12("NCR", "WaveLAN/PCMCIA", 0x24358cd4, 0x1bc50975), - PCMCIA_DEVICE_NULL, -}; -MODULE_DEVICE_TABLE(pcmcia, wavelan_ids); - -static struct pcmcia_driver wavelan_driver = { - .owner = THIS_MODULE, - .drv = { - .name = "wavelan_cs", - }, - .probe = wavelan_probe, - .remove = wavelan_detach, - .id_table = wavelan_ids, - .suspend = wavelan_suspend, - .resume = wavelan_resume, -}; - -static int __init -init_wavelan_cs(void) -{ - return pcmcia_register_driver(&wavelan_driver); -} - -static void __exit -exit_wavelan_cs(void) -{ - pcmcia_unregister_driver(&wavelan_driver); -} - -module_init(init_wavelan_cs); -module_exit(exit_wavelan_cs); diff --git a/drivers/net/wireless/wavelan_cs.h b/drivers/net/wireless/wavelan_cs.h deleted file mode 100644 index 2e4bfe4..0000000 --- a/drivers/net/wireless/wavelan_cs.h +++ /dev/null @@ -1,386 +0,0 @@ -/* - * Wavelan Pcmcia driver - * - * Jean II - HPLB '96 - * - * Reorganization and extension of the driver. - * Original copyright follow. See wavelan_cs.h for details. - * - * This file contain the declarations of the Wavelan hardware. Note that - * the Pcmcia Wavelan include a i82593 controller (see definitions in - * file i82593.h). - * - * The main difference between the pcmcia hardware and the ISA one is - * the Ethernet Controller (i82593 instead of i82586). The i82593 allow - * only one send buffer. The PSA (Parameter Storage Area : EEprom for - * permanent storage of various info) is memory mapped, but not the - * MMI (Modem Management Interface). - */ - -/* - * Definitions for the AT&T GIS (formerly NCR) WaveLAN PCMCIA card: - * An Ethernet-like radio transceiver controlled by an Intel 82593 - * coprocessor. - * - * - **************************************************************************** - * Copyright 1995 - * Anthony D. Joseph - * Massachusetts Institute of Technology - * - * Permission to use, copy, modify, and distribute this program - * for any purpose and without fee is hereby granted, provided - * that this copyright and permission notice appear on all copies - * and supporting documentation, the name of M.I.T. not be used - * in advertising or publicity pertaining to distribution of the - * program without specific prior permission, and notice be given - * in supporting documentation that copying and distribution is - * by permission of M.I.T. M.I.T. makes no representations about - * the suitability of this software for any purpose. It is pro- - * vided "as is" without express or implied warranty. - **************************************************************************** - * - * - * Credits: - * Special thanks to Jan Hoogendoorn of AT&T GIS Utrecht for - * providing extremely useful information about WaveLAN PCMCIA hardware - * - * This driver is based upon several other drivers, in particular: - * David Hinds' Linux driver for the PCMCIA 3c589 ethernet adapter - * Bruce Janson's Linux driver for the AT-bus WaveLAN adapter - * Anders Klemets' PCMCIA WaveLAN adapter driver - * Robert Morris' BSDI driver for the PCMCIA WaveLAN adapter - */ - -#ifndef _WAVELAN_CS_H -#define _WAVELAN_CS_H - -/************************** MAGIC NUMBERS ***************************/ - -/* The detection of the wavelan card is made by reading the MAC address - * from the card and checking it. If you have a non AT&T product (OEM, - * like DEC RoamAbout, or Digital Ocean, Epson, ...), you must modify this - * part to accommodate your hardware... - */ -static const unsigned char MAC_ADDRESSES[][3] = -{ - { 0x08, 0x00, 0x0E }, /* AT&T Wavelan (standard) & DEC RoamAbout */ - { 0x08, 0x00, 0x6A }, /* AT&T Wavelan (alternate) */ - { 0x00, 0x00, 0xE1 }, /* Hitachi Wavelan */ - { 0x00, 0x60, 0x1D } /* Lucent Wavelan (another one) */ - /* Add your card here and send me the patch ! */ -}; - -/* - * Constants used to convert channels to frequencies - */ - -/* Frequency available in the 2.0 modem, in units of 250 kHz - * (as read in the offset register of the dac area). - * Used to map channel numbers used by `wfreqsel' to frequencies - */ -static const short channel_bands[] = { 0x30, 0x58, 0x64, 0x7A, 0x80, 0xA8, - 0xD0, 0xF0, 0xF8, 0x150 }; - -/* Frequencies of the 1.0 modem (fixed frequencies). - * Use to map the PSA `subband' to a frequency - * Note : all frequencies apart from the first one need to be multiplied by 10 - */ -static const int fixed_bands[] = { 915e6, 2.425e8, 2.46e8, 2.484e8, 2.4305e8 }; - - -/*************************** PC INTERFACE ****************************/ - -/* WaveLAN host interface definitions */ - -#define LCCR(base) (base) /* LAN Controller Command Register */ -#define LCSR(base) (base) /* LAN Controller Status Register */ -#define HACR(base) (base+0x1) /* Host Adapter Command Register */ -#define HASR(base) (base+0x1) /* Host Adapter Status Register */ -#define PIORL(base) (base+0x2) /* Program I/O Register Low */ -#define RPLL(base) (base+0x2) /* Receive Pointer Latched Low */ -#define PIORH(base) (base+0x3) /* Program I/O Register High */ -#define RPLH(base) (base+0x3) /* Receive Pointer Latched High */ -#define PIOP(base) (base+0x4) /* Program I/O Port */ -#define MMR(base) (base+0x6) /* MMI Address Register */ -#define MMD(base) (base+0x7) /* MMI Data Register */ - -/* Host Adaptor Command Register bit definitions */ - -#define HACR_LOF (1 << 3) /* Lock Out Flag, toggle every 250ms */ -#define HACR_PWR_STAT (1 << 4) /* Power State, 1=active, 0=sleep */ -#define HACR_TX_DMA_RESET (1 << 5) /* Reset transmit DMA ptr on high */ -#define HACR_RX_DMA_RESET (1 << 6) /* Reset receive DMA ptr on high */ -#define HACR_ROM_WEN (1 << 7) /* EEPROM write enabled when true */ - -#define HACR_RESET (HACR_TX_DMA_RESET | HACR_RX_DMA_RESET) -#define HACR_DEFAULT (HACR_PWR_STAT) - -/* Host Adapter Status Register bit definitions */ - -#define HASR_MMI_BUSY (1 << 2) /* MMI is busy when true */ -#define HASR_LOF (1 << 3) /* Lock out flag status */ -#define HASR_NO_CLK (1 << 4) /* active when modem not connected */ - -/* Miscellaneous bit definitions */ - -#define PIORH_SEL_TX (1 << 5) /* PIOR points to 0=rx/1=tx buffer */ -#define MMR_MMI_WR (1 << 0) /* Next MMI cycle is 0=read, 1=write */ -#define PIORH_MASK 0x1f /* only low 5 bits are significant */ -#define RPLH_MASK 0x1f /* only low 5 bits are significant */ -#define MMI_ADDR_MASK 0x7e /* Bits 1-6 of MMR are significant */ - -/* Attribute Memory map */ - -#define CIS_ADDR 0x0000 /* Card Information Status Register */ -#define PSA_ADDR 0x0e00 /* Parameter Storage Area address */ -#define EEPROM_ADDR 0x1000 /* EEPROM address (unused ?) */ -#define COR_ADDR 0x4000 /* Configuration Option Register */ - -/* Configuration Option Register bit definitions */ - -#define COR_CONFIG (1 << 0) /* Config Index, 0 when unconfigured */ -#define COR_SW_RESET (1 << 7) /* Software Reset on true */ -#define COR_LEVEL_IRQ (1 << 6) /* Level IRQ */ - -/* Local Memory map */ - -#define RX_BASE 0x0000 /* Receive memory, 8 kB */ -#define TX_BASE 0x2000 /* Transmit memory, 2 kB */ -#define UNUSED_BASE 0x2800 /* Unused, 22 kB */ -#define RX_SIZE (TX_BASE-RX_BASE) /* Size of receive area */ -#define RX_SIZE_SHIFT 6 /* Bits to shift in stop register */ - -#define TRUE 1 -#define FALSE 0 - -#define MOD_ENAL 1 -#define MOD_PROM 2 - -/* Size of a MAC address */ -#define WAVELAN_ADDR_SIZE 6 - -/* Maximum size of Wavelan packet */ -#define WAVELAN_MTU 1500 - -#define MAXDATAZ (6 + 6 + 2 + WAVELAN_MTU) - -/********************** PARAMETER STORAGE AREA **********************/ - -/* - * Parameter Storage Area (PSA). - */ -typedef struct psa_t psa_t; -struct psa_t -{ - /* For the PCMCIA Adapter, locations 0x00-0x0F are unused and fixed at 00 */ - unsigned char psa_io_base_addr_1; /* [0x00] Base address 1 ??? */ - unsigned char psa_io_base_addr_2; /* [0x01] Base address 2 */ - unsigned char psa_io_base_addr_3; /* [0x02] Base address 3 */ - unsigned char psa_io_base_addr_4; /* [0x03] Base address 4 */ - unsigned char psa_rem_boot_addr_1; /* [0x04] Remote Boot Address 1 */ - unsigned char psa_rem_boot_addr_2; /* [0x05] Remote Boot Address 2 */ - unsigned char psa_rem_boot_addr_3; /* [0x06] Remote Boot Address 3 */ - unsigned char psa_holi_params; /* [0x07] HOst Lan Interface (HOLI) Parameters */ - unsigned char psa_int_req_no; /* [0x08] Interrupt Request Line */ - unsigned char psa_unused0[7]; /* [0x09-0x0F] unused */ - - unsigned char psa_univ_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x10-0x15] Universal (factory) MAC Address */ - unsigned char psa_local_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x16-1B] Local MAC Address */ - unsigned char psa_univ_local_sel; /* [0x1C] Universal Local Selection */ -#define PSA_UNIVERSAL 0 /* Universal (factory) */ -#define PSA_LOCAL 1 /* Local */ - unsigned char psa_comp_number; /* [0x1D] Compatability Number: */ -#define PSA_COMP_PC_AT_915 0 /* PC-AT 915 MHz */ -#define PSA_COMP_PC_MC_915 1 /* PC-MC 915 MHz */ -#define PSA_COMP_PC_AT_2400 2 /* PC-AT 2.4 GHz */ -#define PSA_COMP_PC_MC_2400 3 /* PC-MC 2.4 GHz */ -#define PSA_COMP_PCMCIA_915 4 /* PCMCIA 915 MHz or 2.0 */ - unsigned char psa_thr_pre_set; /* [0x1E] Modem Threshold Preset */ - unsigned char psa_feature_select; /* [0x1F] Call code required (1=on) */ -#define PSA_FEATURE_CALL_CODE 0x01 /* Call code required (Japan) */ - unsigned char psa_subband; /* [0x20] Subband */ -#define PSA_SUBBAND_915 0 /* 915 MHz or 2.0 */ -#define PSA_SUBBAND_2425 1 /* 2425 MHz */ -#define PSA_SUBBAND_2460 2 /* 2460 MHz */ -#define PSA_SUBBAND_2484 3 /* 2484 MHz */ -#define PSA_SUBBAND_2430_5 4 /* 2430.5 MHz */ - unsigned char psa_quality_thr; /* [0x21] Modem Quality Threshold */ - unsigned char psa_mod_delay; /* [0x22] Modem Delay ??? (reserved) */ - unsigned char psa_nwid[2]; /* [0x23-0x24] Network ID */ - unsigned char psa_nwid_select; /* [0x25] Network ID Select On Off */ - unsigned char psa_encryption_select; /* [0x26] Encryption On Off */ - unsigned char psa_encryption_key[8]; /* [0x27-0x2E] Encryption Key */ - unsigned char psa_databus_width; /* [0x2F] AT bus width select 8/16 */ - unsigned char psa_call_code[8]; /* [0x30-0x37] (Japan) Call Code */ - unsigned char psa_nwid_prefix[2]; /* [0x38-0x39] Roaming domain */ - unsigned char psa_reserved[2]; /* [0x3A-0x3B] Reserved - fixed 00 */ - unsigned char psa_conf_status; /* [0x3C] Conf Status, bit 0=1:config*/ - unsigned char psa_crc[2]; /* [0x3D] CRC-16 over PSA */ - unsigned char psa_crc_status; /* [0x3F] CRC Valid Flag */ -}; - -/* Size for structure checking (if padding is correct) */ -#define PSA_SIZE 64 - -/* Calculate offset of a field in the above structure - * Warning : only even addresses are used */ -#define psaoff(p,f) ((unsigned short) ((void *)(&((psa_t *) ((void *) NULL + (p)))->f) - (void *) NULL)) - -/******************** MODEM MANAGEMENT INTERFACE ********************/ - -/* - * Modem Management Controller (MMC) write structure. - */ -typedef struct mmw_t mmw_t; -struct mmw_t -{ - unsigned char mmw_encr_key[8]; /* encryption key */ - unsigned char mmw_encr_enable; /* enable/disable encryption */ -#define MMW_ENCR_ENABLE_MODE 0x02 /* Mode of security option */ -#define MMW_ENCR_ENABLE_EN 0x01 /* Enable security option */ - unsigned char mmw_unused0[1]; /* unused */ - unsigned char mmw_des_io_invert; /* Encryption option */ -#define MMW_DES_IO_INVERT_RES 0x0F /* Reserved */ -#define MMW_DES_IO_INVERT_CTRL 0xF0 /* Control ??? (set to 0) */ - unsigned char mmw_unused1[5]; /* unused */ - unsigned char mmw_loopt_sel; /* looptest selection */ -#define MMW_LOOPT_SEL_DIS_NWID 0x40 /* disable NWID filtering */ -#define MMW_LOOPT_SEL_INT 0x20 /* activate Attention Request */ -#define MMW_LOOPT_SEL_LS 0x10 /* looptest w/o collision avoidance */ -#define MMW_LOOPT_SEL_LT3A 0x08 /* looptest 3a */ -#define MMW_LOOPT_SEL_LT3B 0x04 /* looptest 3b */ -#define MMW_LOOPT_SEL_LT3C 0x02 /* looptest 3c */ -#define MMW_LOOPT_SEL_LT3D 0x01 /* looptest 3d */ - unsigned char mmw_jabber_enable; /* jabber timer enable */ - /* Abort transmissions > 200 ms */ - unsigned char mmw_freeze; /* freeze / unfreeeze signal level */ - /* 0 : signal level & qual updated for every new message, 1 : frozen */ - unsigned char mmw_anten_sel; /* antenna selection */ -#define MMW_ANTEN_SEL_SEL 0x01 /* direct antenna selection */ -#define MMW_ANTEN_SEL_ALG_EN 0x02 /* antenna selection algo. enable */ - unsigned char mmw_ifs; /* inter frame spacing */ - /* min time between transmission in bit periods (.5 us) - bit 0 ignored */ - unsigned char mmw_mod_delay; /* modem delay (synchro) */ - unsigned char mmw_jam_time; /* jamming time (after collision) */ - unsigned char mmw_unused2[1]; /* unused */ - unsigned char mmw_thr_pre_set; /* level threshold preset */ - /* Discard all packet with signal < this value (4) */ - unsigned char mmw_decay_prm; /* decay parameters */ - unsigned char mmw_decay_updat_prm; /* decay update parameterz */ - unsigned char mmw_quality_thr; /* quality (z-quotient) threshold */ - /* Discard all packet with quality < this value (3) */ - unsigned char mmw_netw_id_l; /* NWID low order byte */ - unsigned char mmw_netw_id_h; /* NWID high order byte */ - /* Network ID or Domain : create virtual net on the air */ - - /* 2.0 Hardware extension - frequency selection support */ - unsigned char mmw_mode_select; /* for analog tests (set to 0) */ - unsigned char mmw_unused3[1]; /* unused */ - unsigned char mmw_fee_ctrl; /* frequency eeprom control */ -#define MMW_FEE_CTRL_PRE 0x10 /* Enable protected instructions */ -#define MMW_FEE_CTRL_DWLD 0x08 /* Download eeprom to mmc */ -#define MMW_FEE_CTRL_CMD 0x07 /* EEprom commands : */ -#define MMW_FEE_CTRL_READ 0x06 /* Read */ -#define MMW_FEE_CTRL_WREN 0x04 /* Write enable */ -#define MMW_FEE_CTRL_WRITE 0x05 /* Write data to address */ -#define MMW_FEE_CTRL_WRALL 0x04 /* Write data to all addresses */ -#define MMW_FEE_CTRL_WDS 0x04 /* Write disable */ -#define MMW_FEE_CTRL_PRREAD 0x16 /* Read addr from protect register */ -#define MMW_FEE_CTRL_PREN 0x14 /* Protect register enable */ -#define MMW_FEE_CTRL_PRCLEAR 0x17 /* Unprotect all registers */ -#define MMW_FEE_CTRL_PRWRITE 0x15 /* Write addr in protect register */ -#define MMW_FEE_CTRL_PRDS 0x14 /* Protect register disable */ - /* Never issue this command (PRDS) : it's irreversible !!! */ - - unsigned char mmw_fee_addr; /* EEprom address */ -#define MMW_FEE_ADDR_CHANNEL 0xF0 /* Select the channel */ -#define MMW_FEE_ADDR_OFFSET 0x0F /* Offset in channel data */ -#define MMW_FEE_ADDR_EN 0xC0 /* FEE_CTRL enable operations */ -#define MMW_FEE_ADDR_DS 0x00 /* FEE_CTRL disable operations */ -#define MMW_FEE_ADDR_ALL 0x40 /* FEE_CTRL all operations */ -#define MMW_FEE_ADDR_CLEAR 0xFF /* FEE_CTRL clear operations */ - - unsigned char mmw_fee_data_l; /* Write data to EEprom */ - unsigned char mmw_fee_data_h; /* high octet */ - unsigned char mmw_ext_ant; /* Setting for external antenna */ -#define MMW_EXT_ANT_EXTANT 0x01 /* Select external antenna */ -#define MMW_EXT_ANT_POL 0x02 /* Polarity of the antenna */ -#define MMW_EXT_ANT_INTERNAL 0x00 /* Internal antenna */ -#define MMW_EXT_ANT_EXTERNAL 0x03 /* External antenna */ -#define MMW_EXT_ANT_IQ_TEST 0x1C /* IQ test pattern (set to 0) */ -} __attribute__((packed)); - -/* Size for structure checking (if padding is correct) */ -#define MMW_SIZE 37 - -/* Calculate offset of a field in the above structure */ -#define mmwoff(p,f) (unsigned short)((void *)(&((mmw_t *)((void *)0 + (p)))->f) - (void *)0) - - -/* - * Modem Management Controller (MMC) read structure. - */ -typedef struct mmr_t mmr_t; -struct mmr_t -{ - unsigned char mmr_unused0[8]; /* unused */ - unsigned char mmr_des_status; /* encryption status */ - unsigned char mmr_des_avail; /* encryption available (0x55 read) */ -#define MMR_DES_AVAIL_DES 0x55 /* DES available */ -#define MMR_DES_AVAIL_AES 0x33 /* AES (AT&T) available */ - unsigned char mmr_des_io_invert; /* des I/O invert register */ - unsigned char mmr_unused1[5]; /* unused */ - unsigned char mmr_dce_status; /* DCE status */ -#define MMR_DCE_STATUS_RX_BUSY 0x01 /* receiver busy */ -#define MMR_DCE_STATUS_LOOPT_IND 0x02 /* loop test indicated */ -#define MMR_DCE_STATUS_TX_BUSY 0x04 /* transmitter on */ -#define MMR_DCE_STATUS_JBR_EXPIRED 0x08 /* jabber timer expired */ -#define MMR_DCE_STATUS 0x0F /* mask to get the bits */ - unsigned char mmr_dsp_id; /* DSP id (AA = Daedalus rev A) */ - unsigned char mmr_unused2[2]; /* unused */ - unsigned char mmr_correct_nwid_l; /* # of correct NWID's rxd (low) */ - unsigned char mmr_correct_nwid_h; /* # of correct NWID's rxd (high) */ - /* Warning : Read high order octet first !!! */ - unsigned char mmr_wrong_nwid_l; /* # of wrong NWID's rxd (low) */ - unsigned char mmr_wrong_nwid_h; /* # of wrong NWID's rxd (high) */ - unsigned char mmr_thr_pre_set; /* level threshold preset */ -#define MMR_THR_PRE_SET 0x3F /* level threshold preset */ -#define MMR_THR_PRE_SET_CUR 0x80 /* Current signal above it */ - unsigned char mmr_signal_lvl; /* signal level */ -#define MMR_SIGNAL_LVL 0x3F /* signal level */ -#define MMR_SIGNAL_LVL_VALID 0x80 /* Updated since last read */ - unsigned char mmr_silence_lvl; /* silence level (noise) */ -#define MMR_SILENCE_LVL 0x3F /* silence level */ -#define MMR_SILENCE_LVL_VALID 0x80 /* Updated since last read */ - unsigned char mmr_sgnl_qual; /* signal quality */ -#define MMR_SGNL_QUAL 0x0F /* signal quality */ -#define MMR_SGNL_QUAL_ANT 0x80 /* current antenna used */ - unsigned char mmr_netw_id_l; /* NWID low order byte ??? */ - unsigned char mmr_unused3[3]; /* unused */ - - /* 2.0 Hardware extension - frequency selection support */ - unsigned char mmr_fee_status; /* Status of frequency eeprom */ -#define MMR_FEE_STATUS_ID 0xF0 /* Modem revision id */ -#define MMR_FEE_STATUS_DWLD 0x08 /* Download in progress */ -#define MMR_FEE_STATUS_BUSY 0x04 /* EEprom busy */ - unsigned char mmr_unused4[1]; /* unused */ - unsigned char mmr_fee_data_l; /* Read data from eeprom (low) */ - unsigned char mmr_fee_data_h; /* Read data from eeprom (high) */ -}; - -/* Size for structure checking (if padding is correct) */ -#define MMR_SIZE 36 - -/* Calculate offset of a field in the above structure */ -#define mmroff(p,f) (unsigned short)((void *)(&((mmr_t *)((void *)0 + (p)))->f) - (void *)0) - - -/* Make the two above structures one */ -typedef union mm_t -{ - struct mmw_t w; /* Write to the mmc */ - struct mmr_t r; /* Read from the mmc */ -} mm_t; - -#endif /* _WAVELAN_CS_H */ diff --git a/drivers/net/wireless/wavelan_cs.p.h b/drivers/net/wireless/wavelan_cs.p.h deleted file mode 100644 index 81d9153..0000000 --- a/drivers/net/wireless/wavelan_cs.p.h +++ /dev/null @@ -1,766 +0,0 @@ -/* - * Wavelan Pcmcia driver - * - * Jean II - HPLB '96 - * - * Reorganisation and extension of the driver. - * - * This file contain all definition and declarations necessary for the - * wavelan pcmcia driver. This file is a private header, so it should - * be included only on wavelan_cs.c !!! - */ - -#ifndef WAVELAN_CS_P_H -#define WAVELAN_CS_P_H - -/************************** DOCUMENTATION **************************/ -/* - * This driver provide a Linux interface to the Wavelan Pcmcia hardware - * The Wavelan is a product of Lucent (http://www.wavelan.com/). - * This division was formerly part of NCR and then AT&T. - * Wavelan are also distributed by DEC (RoamAbout DS)... - * - * To know how to use this driver, read the PCMCIA HOWTO. - * If you want to exploit the many other fonctionalities, look comments - * in the code... - * - * This driver is the result of the effort of many peoples (see below). - */ - -/* ------------------------ SPECIFIC NOTES ------------------------ */ -/* - * Web page - * -------- - * I try to maintain a web page with the Wireless LAN Howto at : - * http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Wavelan.html - * - * SMP - * --- - * We now are SMP compliant (I eventually fixed the remaining bugs). - * The driver has been tested on a dual P6-150 and survived my usual - * set of torture tests. - * Anyway, I spent enough time chasing interrupt re-entrancy during - * errors or reconfigure, and I designed the locked/unlocked sections - * of the driver with great care, and with the recent addition of - * the spinlock (thanks to the new API), we should be quite close to - * the truth. - * The SMP/IRQ locking is quite coarse and conservative (i.e. not fast), - * but better safe than sorry (especially at 2 Mb/s ;-). - * - * I have also looked into disabling only our interrupt on the card - * (via HACR) instead of all interrupts in the processor (via cli), - * so that other driver are not impacted, and it look like it's - * possible, but it's very tricky to do right (full of races). As - * the gain would be mostly for SMP systems, it can wait... - * - * Debugging and options - * --------------------- - * You will find below a set of '#define" allowing a very fine control - * on the driver behaviour and the debug messages printed. - * The main options are : - * o WAVELAN_ROAMING, for the experimental roaming support. - * o SET_PSA_CRC, to have your card correctly recognised by - * an access point and the Point-to-Point diagnostic tool. - * o USE_PSA_CONFIG, to read configuration from the PSA (EEprom) - * (otherwise we always start afresh with some defaults) - * - * wavelan_cs.o is darn too big - * ------------------------- - * That's true ! There is a very simple way to reduce the driver - * object by 33% (yes !). Comment out the following line : - * #include <linux/wireless.h> - * Other compile options can also reduce the size of it... - * - * MAC address and hardware detection : - * ---------------------------------- - * The detection code of the wavelan chech that the first 3 - * octets of the MAC address fit the company code. This type of - * detection work well for AT&T cards (because the AT&T code is - * hardcoded in wavelan_cs.h), but of course will fail for other - * manufacturer. - * - * If you are sure that your card is derived from the wavelan, - * here is the way to configure it : - * 1) Get your MAC address - * a) With your card utilities (wfreqsel, instconf, ...) - * b) With the driver : - * o compile the kernel with DEBUG_CONFIG_INFO enabled - * o Boot and look the card messages - * 2) Set your MAC code (3 octets) in MAC_ADDRESSES[][3] (wavelan_cs.h) - * 3) Compile & verify - * 4) Send me the MAC code - I will include it in the next version... - * - */ - -/* --------------------- WIRELESS EXTENSIONS --------------------- */ -/* - * This driver is the first one to support "wireless extensions". - * This set of extensions provide you some way to control the wireless - * caracteristics of the hardware in a standard way and support for - * applications for taking advantage of it (like Mobile IP). - * - * It might be a good idea as well to fetch the wireless tools to - * configure the device and play a bit. - */ - -/* ---------------------------- FILES ---------------------------- */ -/* - * wavelan_cs.c : The actual code for the driver - C functions - * - * wavelan_cs.p.h : Private header : local types / vars for the driver - * - * wavelan_cs.h : Description of the hardware interface & structs - * - * i82593.h : Description if the Ethernet controller - */ - -/* --------------------------- HISTORY --------------------------- */ -/* - * The history of the Wavelan drivers is as complicated as history of - * the Wavelan itself (NCR -> AT&T -> Lucent). - * - * All started with Anders Klemets <klemets@paul.rutgers.edu>, - * writing a Wavelan ISA driver for the MACH microkernel. Girish - * Welling <welling@paul.rutgers.edu> had also worked on it. - * Keith Moore modify this for the Pcmcia hardware. - * - * Robert Morris <rtm@das.harvard.edu> port these two drivers to BSDI - * and add specific Pcmcia support (there is currently no equivalent - * of the PCMCIA package under BSD...). - * - * Jim Binkley <jrb@cs.pdx.edu> port both BSDI drivers to FreeBSD. - * - * Bruce Janson <bruce@cs.usyd.edu.au> port the BSDI ISA driver to Linux. - * - * Anthony D. Joseph <adj@lcs.mit.edu> started modify Bruce driver - * (with help of the BSDI PCMCIA driver) for PCMCIA. - * Yunzhou Li <yunzhou@strat.iol.unh.edu> finished is work. - * Joe Finney <joe@comp.lancs.ac.uk> patched the driver to start - * correctly 2.00 cards (2.4 GHz with frequency selection). - * David Hinds <dahinds@users.sourceforge.net> integrated the whole in his - * Pcmcia package (+ bug corrections). - * - * I (Jean Tourrilhes - jt@hplb.hpl.hp.com) then started to make some - * patchs to the Pcmcia driver. After, I added code in the ISA driver - * for Wireless Extensions and full support of frequency selection - * cards. Now, I'm doing the same to the Pcmcia driver + some - * reorganisation. - * Loeke Brederveld <lbrederv@wavelan.com> from Lucent has given me - * much needed informations on the Wavelan hardware. - */ - -/* By the way : for the copyright & legal stuff : - * Almost everybody wrote code under GNU or BSD license (or alike), - * and want that their original copyright remain somewhere in the - * code (for myself, I go with the GPL). - * Nobody want to take responsibility for anything, except the fame... - */ - -/* --------------------------- CREDITS --------------------------- */ -/* - * Credits: - * Special thanks to Jan Hoogendoorn of AT&T GIS Utrecht and - * Loeke Brederveld of Lucent for providing extremely useful - * information about WaveLAN PCMCIA hardware - * - * This driver is based upon several other drivers, in particular: - * David Hinds' Linux driver for the PCMCIA 3c589 ethernet adapter - * Bruce Janson's Linux driver for the AT-bus WaveLAN adapter - * Anders Klemets' PCMCIA WaveLAN adapter driver - * Robert Morris' BSDI driver for the PCMCIA WaveLAN adapter - * - * Additional Credits: - * - * This software was originally developed under Linux 1.2.3 - * (Slackware 2.0 distribution). - * And then under Linux 2.0.x (Debian 1.1 -> 2.2 - pcmcia 2.8.18+) - * with an HP OmniBook 4000 and then a 5500. - * - * It is based on other device drivers and information either written - * or supplied by: - * James Ashton (jaa101@syseng.anu.edu.au), - * Ajay Bakre (bakre@paul.rutgers.edu), - * Donald Becker (becker@super.org), - * Jim Binkley <jrb@cs.pdx.edu>, - * Loeke Brederveld <lbrederv@wavelan.com>, - * Allan Creighton (allanc@cs.su.oz.au), - * Brent Elphick <belphick@uwaterloo.ca>, - * Joe Finney <joe@comp.lancs.ac.uk>, - * Matthew Geier (matthew@cs.su.oz.au), - * Remo di Giovanni (remo@cs.su.oz.au), - * Mark Hagan (mhagan@wtcpost.daytonoh.NCR.COM), - * David Hinds <dahinds@users.sourceforge.net>, - * Jan Hoogendoorn (c/o marteijn@lucent.com), - * Bruce Janson <bruce@cs.usyd.edu.au>, - * Anthony D. Joseph <adj@lcs.mit.edu>, - * Anders Klemets (klemets@paul.rutgers.edu), - * Yunzhou Li <yunzhou@strat.iol.unh.edu>, - * Marc Meertens (mmeertens@lucent.com), - * Keith Moore, - * Robert Morris (rtm@das.harvard.edu), - * Ian Parkin (ian@cs.su.oz.au), - * John Rosenberg (johnr@cs.su.oz.au), - * George Rossi (george@phm.gov.au), - * Arthur Scott (arthur@cs.su.oz.au), - * Stanislav Sinyagin <stas@isf.ru> - * Peter Storey, - * Jean Tourrilhes <jt@hpl.hp.com>, - * Girish Welling (welling@paul.rutgers.edu) - * Clark Woodworth <clark@hiway1.exit109.com> - * Yongguang Zhang <ygz@isl.hrl.hac.com>... - */ - -/* ------------------------- IMPROVEMENTS ------------------------- */ -/* - * I proudly present : - * - * Changes made in 2.8.22 : - * ---------------------- - * - improved wv_set_multicast_list - * - catch spurious interrupt - * - correct release of the device - * - * Changes mades in release : - * ------------------------ - * - Reorganisation of the code, function name change - * - Creation of private header (wavelan_cs.h) - * - Reorganised debug messages - * - More comments, history, ... - * - Configure earlier (in "insert" instead of "open") - * and do things only once - * - mmc_init : configure the PSA if not done - * - mmc_init : 2.00 detection better code for 2.00 init - * - better info at startup - * - Correct a HUGE bug (volatile & uncalibrated busy loop) - * in wv_82593_cmd => config speedup - * - Stop receiving & power down on close (and power up on open) - * use "ifconfig down" & "ifconfig up ; route add -net ..." - * - Send packets : add watchdog instead of pooling - * - Receive : check frame wrap around & try to recover some frames - * - wavelan_set_multicast_list : avoid reset - * - add wireless extensions (ioctl & get_wireless_stats) - * get/set nwid/frequency on fly, info for /proc/net/wireless - * - Suppress useless stuff from lp (net_local), but add link - * - More inlines - * - Lot of others minor details & cleanups - * - * Changes made in second release : - * ------------------------------ - * - Optimise wv_85893_reconfig stuff, fix potential problems - * - Change error values for ioctl - * - Non blocking wv_ru_stop() + call wv_reset() in case of problems - * - Remove development printk from wavelan_watchdog() - * - Remove of the watchdog to wavelan_close instead of wavelan_release - * fix potential problems... - * - Start debugging suspend stuff (but it's still a bit weird) - * - Debug & optimize dump header/packet in Rx & Tx (debug) - * - Use "readb" and "writeb" to be kernel 2.1 compliant - * - Better handling of bogus interrupts - * - Wireless extension : SETSPY and GETSPY - * - Remove old stuff (stats - for those needing it, just ask me...) - * - Make wireless extensions optional - * - * Changes made in third release : - * ----------------------------- - * - cleanups & typos - * - modif wireless ext (spy -> only one pointer) - * - new private ioctl to set/get quality & level threshold - * - Init : correct default value of level threshold for pcmcia - * - kill watchdog in hw_reset - * - more 2.1 support (copy_to/from_user instead of memcpy_to/fromfs) - * - Add message level (debug stuff in /var/adm/debug & errors not - * displayed at console and still in /var/adm/messages) - * - * Changes made in fourth release : - * ------------------------------ - * - multicast support (yes !) thanks to Yongguang Zhang. - * - * Changes made in fifth release (2.9.0) : - * ------------------------------------- - * - Revisited multicast code (it was mostly wrong). - * - protect code in wv_82593_reconfig with dev->tbusy (oups !) - * - * Changes made in sixth release (2.9.1a) : - * -------------------------------------- - * - Change the detection code for multi manufacturer code support - * - Correct bug (hang kernel) in init when we were "rejecting" a card - * - * Changes made in seventh release (2.9.1b) : - * ---------------------------------------- - * - Update to wireless extensions changes - * - Silly bug in card initial configuration (psa_conf_status) - * - * Changes made in eigth release : - * ----------------------------- - * - Small bug in debug code (probably not the last one...) - * - 1.2.13 support (thanks to Clark Woodworth) - * - * Changes made for release in 2.9.2b : - * ---------------------------------- - * - Level threshold is now a standard wireless extension (version 4 !) - * - modules parameters types for kernel > 2.1.17 - * - updated man page - * - Others cleanup from David Hinds - * - * Changes made for release in 2.9.5 : - * --------------------------------- - * - byte count stats (courtesy of David Hinds) - * - Remove dev_tint stuff (courtesy of David Hinds) - * - Others cleanup from David Hinds - * - Encryption setting from Brent Elphick (thanks a lot !) - * - 'base' to 'u_long' for the Alpha (thanks to Stanislav Sinyagin) - * - * Changes made for release in 2.9.6 : - * --------------------------------- - * - fix bug : no longuer disable watchdog in case of bogus interrupt - * - increase timeout in config code for picky hardware - * - mask unused bits in status (Wireless Extensions) - * - * Changes integrated by Justin Seger <jseger@MIT.EDU> & David Hinds : - * ----------------------------------------------------------------- - * - Roaming "hack" from Joe Finney <joe@comp.lancs.ac.uk> - * - PSA CRC code from Bob Gray <rgray@bald.cs.dartmouth.edu> - * - Better initialisation of the i82593 controller - * from Joseph K. O'Sullivan <josullvn+@cs.cmu.edu> - * - * Changes made for release in 3.0.10 : - * ---------------------------------- - * - Fix eject "hang" of the driver under 2.2.X : - * o create wv_flush_stale_links() - * o Rename wavelan_release to wv_pcmcia_release & move up - * o move unregister_netdev to wavelan_detach() - * o wavelan_release() no longer call wavelan_detach() - * o Suppress "release" timer - * o Other cleanups & fixes - * - New MAC address in the probe - * - Reorg PSA_CRC code (endian neutral & cleaner) - * - Correct initialisation of the i82593 from Lucent manual - * - Put back the watchdog, with larger timeout - * - TRANSMIT_NO_CRC is a "normal" error, so recover from it - * from Derrick J Brashear <shadow@dementia.org> - * - Better handling of TX and RX normal failure conditions - * - #ifdef out all the roaming code - * - Add ESSID & "AP current address" ioctl stubs - * - General cleanup of the code - * - * Changes made for release in 3.0.13 : - * ---------------------------------- - * - Re-enable compilation of roaming code by default, but with - * do_roaming = 0 - * - Nuke `nwid=nwid^ntohs(beacon->domain_id)' in wl_roam_gather - * at the demand of John Carol Langford <jcl@gs176.sp.cs.cmu.edu> - * - Introduced WAVELAN_ROAMING_EXT for incomplete ESSID stuff. - * - * Changes made for release in 3.0.15 : - * ---------------------------------- - * - Change e-mail and web page addresses - * - Watchdog timer is now correctly expressed in HZ, not in jiffies - * - Add channel number to the list of frequencies in range - * - Add the (short) list of bit-rates in range - * - Developp a new sensitivity... (sens.value & sens.fixed) - * - * Changes made for release in 3.1.2 : - * --------------------------------- - * - Fix check for root permission (break instead of exit) - * - New nwid & encoding setting (Wireless Extension 9) - * - * Changes made for release in 3.1.12 : - * ---------------------------------- - * - reworked wv_82593_cmd to avoid using the IRQ handler and doing - * ugly things with interrupts. - * - Add IRQ protection in 82593_config/ru_start/ru_stop/watchdog - * - Update to new network API (softnet - 2.3.43) : - * o replace dev->tbusy (David + me) - * o replace dev->tstart (David + me) - * o remove dev->interrupt (David) - * o add SMP locking via spinlock in splxx (me) - * o add spinlock in interrupt handler (me) - * o use kernel watchdog instead of ours (me) - * o verify that all the changes make sense and work (me) - * - Re-sync kernel/pcmcia versions (not much actually) - * - A few other cleanups (David & me)... - * - * Changes made for release in 3.1.22 : - * ---------------------------------- - * - Check that SMP works, remove annoying log message - * - * Changes made for release in 3.1.24 : - * ---------------------------------- - * - Fix unfrequent card lockup when watchdog was reseting the hardware : - * o control first busy loop in wv_82593_cmd() - * o Extend spinlock protection in wv_hw_config() - * - * Changes made for release in 3.1.33 : - * ---------------------------------- - * - Optional use new driver API for Wireless Extensions : - * o got rid of wavelan_ioctl() - * o use a bunch of iw_handler instead - * - * Changes made for release in 3.2.1 : - * --------------------------------- - * - Set dev->trans_start to avoid filling the logs - * (and generating useless abort commands) - * - Avoid deadlocks in mmc_out()/mmc_in() - * - * Wishes & dreams: - * ---------------- - * - Cleanup and integrate the roaming code - * (std debug, set DomainID, decay avg and co...) - */ - -/***************************** INCLUDES *****************************/ - -/* Linux headers that we need */ -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/sched.h> -#include <linux/ptrace.h> -#include <linux/slab.h> -#include <linux/string.h> -#include <linux/timer.h> -#include <linux/interrupt.h> -#include <linux/spinlock.h> -#include <linux/in.h> -#include <linux/delay.h> -#include <linux/bitops.h> -#include <asm/uaccess.h> -#include <asm/io.h> -#include <asm/system.h> - -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/if_arp.h> -#include <linux/ioport.h> -#include <linux/fcntl.h> -#include <linux/ethtool.h> -#include <linux/wireless.h> /* Wireless extensions */ -#include <net/iw_handler.h> /* New driver API */ - -/* Pcmcia headers that we need */ -#include <pcmcia/cs_types.h> -#include <pcmcia/cs.h> -#include <pcmcia/cistpl.h> -#include <pcmcia/cisreg.h> -#include <pcmcia/ds.h> - -/* Wavelan declarations */ -#include "i82593.h" /* Definitions for the Intel chip */ - -#include "wavelan_cs.h" /* Others bits of the hardware */ - -/************************** DRIVER OPTIONS **************************/ -/* - * `#define' or `#undef' the following constant to change the behaviour - * of the driver... - */ -#define WAVELAN_ROAMING /* Include experimental roaming code */ -#undef WAVELAN_ROAMING_EXT /* Enable roaming wireless extensions */ -#undef SET_PSA_CRC /* Set the CRC in PSA (slower) */ -#define USE_PSA_CONFIG /* Use info from the PSA */ -#undef EEPROM_IS_PROTECTED /* Doesn't seem to be necessary */ -#define MULTICAST_AVOID /* Avoid extra multicast (I'm sceptical) */ -#undef SET_MAC_ADDRESS /* Experimental */ - -/* Warning : these stuff will slow down the driver... */ -#define WIRELESS_SPY /* Enable spying addresses */ -#undef HISTOGRAM /* Enable histogram of sig level... */ - -/****************************** DEBUG ******************************/ - -#undef DEBUG_MODULE_TRACE /* Module insertion/removal */ -#undef DEBUG_CALLBACK_TRACE /* Calls made by Linux */ -#undef DEBUG_INTERRUPT_TRACE /* Calls to handler */ -#undef DEBUG_INTERRUPT_INFO /* type of interrupt & so on */ -#define DEBUG_INTERRUPT_ERROR /* problems */ -#undef DEBUG_CONFIG_TRACE /* Trace the config functions */ -#undef DEBUG_CONFIG_INFO /* What's going on... */ -#define DEBUG_CONFIG_ERRORS /* Errors on configuration */ -#undef DEBUG_TX_TRACE /* Transmission calls */ -#undef DEBUG_TX_INFO /* Header of the transmitted packet */ -#undef DEBUG_TX_FAIL /* Normal failure conditions */ -#define DEBUG_TX_ERROR /* Unexpected conditions */ -#undef DEBUG_RX_TRACE /* Transmission calls */ -#undef DEBUG_RX_INFO /* Header of the transmitted packet */ -#undef DEBUG_RX_FAIL /* Normal failure conditions */ -#define DEBUG_RX_ERROR /* Unexpected conditions */ -#undef DEBUG_PACKET_DUMP /* Dump packet on the screen */ -#undef DEBUG_IOCTL_TRACE /* Misc call by Linux */ -#undef DEBUG_IOCTL_INFO /* Various debug info */ -#define DEBUG_IOCTL_ERROR /* What's going wrong */ -#define DEBUG_BASIC_SHOW /* Show basic startup info */ -#undef DEBUG_VERSION_SHOW /* Print version info */ -#undef DEBUG_PSA_SHOW /* Dump psa to screen */ -#undef DEBUG_MMC_SHOW /* Dump mmc to screen */ -#undef DEBUG_SHOW_UNUSED /* Show also unused fields */ -#undef DEBUG_I82593_SHOW /* Show i82593 status */ -#undef DEBUG_DEVICE_SHOW /* Show device parameters */ - -/************************ CONSTANTS & MACROS ************************/ - -#ifdef DEBUG_VERSION_SHOW -static const char *version = "wavelan_cs.c : v24 (SMP + wireless extensions) 11/1/02\n"; -#endif - -/* Watchdog temporisation */ -#define WATCHDOG_JIFFIES (256*HZ/100) - -/* Fix a bug in some old wireless extension definitions */ -#ifndef IW_ESSID_MAX_SIZE -#define IW_ESSID_MAX_SIZE 32 -#endif - -/* ------------------------ PRIVATE IOCTL ------------------------ */ - -#define SIOCSIPQTHR SIOCIWFIRSTPRIV /* Set quality threshold */ -#define SIOCGIPQTHR SIOCIWFIRSTPRIV + 1 /* Get quality threshold */ -#define SIOCSIPROAM SIOCIWFIRSTPRIV + 2 /* Set roaming state */ -#define SIOCGIPROAM SIOCIWFIRSTPRIV + 3 /* Get roaming state */ - -#define SIOCSIPHISTO SIOCIWFIRSTPRIV + 4 /* Set histogram ranges */ -#define SIOCGIPHISTO SIOCIWFIRSTPRIV + 5 /* Get histogram values */ - -/*************************** WaveLAN Roaming **************************/ -#ifdef WAVELAN_ROAMING /* Conditional compile, see above in options */ - -#define WAVELAN_ROAMING_DEBUG 0 /* 1 = Trace of handover decisions */ - /* 2 = Info on each beacon rcvd... */ -#define MAX_WAVEPOINTS 7 /* Max visible at one time */ -#define WAVEPOINT_HISTORY 5 /* SNR sample history slow search */ -#define WAVEPOINT_FAST_HISTORY 2 /* SNR sample history fast search */ -#define SEARCH_THRESH_LOW 10 /* SNR to enter cell search */ -#define SEARCH_THRESH_HIGH 13 /* SNR to leave cell search */ -#define WAVELAN_ROAMING_DELTA 1 /* Hysteresis value (+/- SNR) */ -#define CELL_TIMEOUT 2*HZ /* in jiffies */ - -#define FAST_CELL_SEARCH 1 /* Boolean values... */ -#define NWID_PROMISC 1 /* for code clarity. */ - -typedef struct wavepoint_beacon -{ - unsigned char dsap, /* Unused */ - ssap, /* Unused */ - ctrl, /* Unused */ - O,U,I, /* Unused */ - spec_id1, /* Unused */ - spec_id2, /* Unused */ - pdu_type, /* Unused */ - seq; /* WavePoint beacon sequence number */ - __be16 domain_id, /* WavePoint Domain ID */ - nwid; /* WavePoint NWID */ -} wavepoint_beacon; - -typedef struct wavepoint_history -{ - unsigned short nwid; /* WavePoint's NWID */ - int average_slow; /* SNR running average */ - int average_fast; /* SNR running average */ - unsigned char sigqual[WAVEPOINT_HISTORY]; /* Ringbuffer of recent SNR's */ - unsigned char qualptr; /* Index into ringbuffer */ - unsigned char last_seq; /* Last seq. no seen for WavePoint */ - struct wavepoint_history *next; /* Next WavePoint in table */ - struct wavepoint_history *prev; /* Previous WavePoint in table */ - unsigned long last_seen; /* Time of last beacon recvd, jiffies */ -} wavepoint_history; - -struct wavepoint_table -{ - wavepoint_history *head; /* Start of ringbuffer */ - int num_wavepoints; /* No. of WavePoints visible */ - unsigned char locked; /* Table lock */ -}; - -#endif /* WAVELAN_ROAMING */ - -/****************************** TYPES ******************************/ - -/* Shortcuts */ -typedef struct iw_statistics iw_stats; -typedef struct iw_quality iw_qual; -typedef struct iw_freq iw_freq; -typedef struct net_local net_local; -typedef struct timer_list timer_list; - -/* Basic types */ -typedef u_char mac_addr[WAVELAN_ADDR_SIZE]; /* Hardware address */ - -/* - * Static specific data for the interface. - * - * For each network interface, Linux keep data in two structure. "device" - * keep the generic data (same format for everybody) and "net_local" keep - * the additional specific data. - */ -struct net_local -{ - dev_node_t node; /* ???? What is this stuff ???? */ - struct net_device * dev; /* Reverse link... */ - spinlock_t spinlock; /* Serialize access to the hardware (SMP) */ - struct pcmcia_device * link; /* pcmcia structure */ - int nresets; /* Number of hw resets */ - u_char configured; /* If it is configured */ - u_char reconfig_82593; /* Need to reconfigure the controller */ - u_char promiscuous; /* Promiscuous mode */ - u_char allmulticast; /* All Multicast mode */ - int mc_count; /* Number of multicast addresses */ - - int stop; /* Current i82593 Stop Hit Register */ - int rfp; /* Last DMA machine receive pointer */ - int overrunning; /* Receiver overrun flag */ - - iw_stats wstats; /* Wireless specific stats */ - - struct iw_spy_data spy_data; - struct iw_public_data wireless_data; - -#ifdef HISTOGRAM - int his_number; /* Number of intervals */ - u_char his_range[16]; /* Boundaries of interval ]n-1; n] */ - u_long his_sum[16]; /* Sum in interval */ -#endif /* HISTOGRAM */ -#ifdef WAVELAN_ROAMING - u_long domain_id; /* Domain ID we lock on for roaming */ - int filter_domains; /* Check Domain ID of beacon found */ - struct wavepoint_table wavepoint_table; /* Table of visible WavePoints*/ - wavepoint_history * curr_point; /* Current wavepoint */ - int cell_search; /* Searching for new cell? */ - struct timer_list cell_timer; /* Garbage collection */ -#endif /* WAVELAN_ROAMING */ - void __iomem *mem; -}; - -/* ----------------- MODEM MANAGEMENT SUBROUTINES ----------------- */ -static inline u_char /* data */ - hasr_read(u_long); /* Read the host interface : base address */ -static void - hacr_write(u_long, /* Write to host interface : base address */ - u_char), /* data */ - hacr_write_slow(u_long, - u_char); -static void - psa_read(struct net_device *, /* Read the Parameter Storage Area */ - int, /* offset in PSA */ - u_char *, /* buffer to fill */ - int), /* size to read */ - psa_write(struct net_device *, /* Write to the PSA */ - int, /* Offset in psa */ - u_char *, /* Buffer in memory */ - int); /* Length of buffer */ -static void - mmc_out(u_long, /* Write 1 byte to the Modem Manag Control */ - u_short, - u_char), - mmc_write(u_long, /* Write n bytes to the MMC */ - u_char, - u_char *, - int); -static u_char /* Read 1 byte from the MMC */ - mmc_in(u_long, - u_short); -static void - mmc_read(u_long, /* Read n bytes from the MMC */ - u_char, - u_char *, - int), - fee_wait(u_long, /* Wait for frequency EEprom : base address */ - int, /* Base delay to wait for */ - int); /* Number of time to wait */ -static void - fee_read(u_long, /* Read the frequency EEprom : base address */ - u_short, /* destination offset */ - u_short *, /* data buffer */ - int); /* number of registers */ -/* ---------------------- I82593 SUBROUTINES ----------------------- */ -static int - wv_82593_cmd(struct net_device *, /* synchronously send a command to i82593 */ - char *, - int, - int); -static inline int - wv_diag(struct net_device *); /* Diagnostique the i82593 */ -static int - read_ringbuf(struct net_device *, /* Read a receive buffer */ - int, - char *, - int); -static void - wv_82593_reconfig(struct net_device *); /* Reconfigure the controller */ -/* ------------------- DEBUG & INFO SUBROUTINES ------------------- */ -static void - wv_init_info(struct net_device *); /* display startup info */ -/* ------------------- IOCTL, STATS & RECONFIG ------------------- */ -static iw_stats * - wavelan_get_wireless_stats(struct net_device *); -/* ----------------------- PACKET RECEPTION ----------------------- */ -static int - wv_start_of_frame(struct net_device *, /* Seek beggining of current frame */ - int, /* end of frame */ - int); /* start of buffer */ -static void - wv_packet_read(struct net_device *, /* Read a packet from a frame */ - int, - int), - wv_packet_rcv(struct net_device *); /* Read all packets waiting */ -/* --------------------- PACKET TRANSMISSION --------------------- */ -static void - wv_packet_write(struct net_device *, /* Write a packet to the Tx buffer */ - void *, - short); -static netdev_tx_t - wavelan_packet_xmit(struct sk_buff *, /* Send a packet */ - struct net_device *); -/* -------------------- HARDWARE CONFIGURATION -------------------- */ -static int - wv_mmc_init(struct net_device *); /* Initialize the modem */ -static int - wv_ru_stop(struct net_device *), /* Stop the i82593 receiver unit */ - wv_ru_start(struct net_device *); /* Start the i82593 receiver unit */ -static int - wv_82593_config(struct net_device *); /* Configure the i82593 */ -static int - wv_pcmcia_reset(struct net_device *); /* Reset the pcmcia interface */ -static int - wv_hw_config(struct net_device *); /* Reset & configure the whole hardware */ -static void - wv_hw_reset(struct net_device *); /* Same, + start receiver unit */ -static int - wv_pcmcia_config(struct pcmcia_device *); /* Configure the pcmcia interface */ -static void - wv_pcmcia_release(struct pcmcia_device *);/* Remove a device */ -/* ---------------------- INTERRUPT HANDLING ---------------------- */ -static irqreturn_t - wavelan_interrupt(int, /* Interrupt handler */ - void *); -static void - wavelan_watchdog(struct net_device *); /* Transmission watchdog */ -/* ------------------- CONFIGURATION CALLBACKS ------------------- */ -static int - wavelan_open(struct net_device *), /* Open the device */ - wavelan_close(struct net_device *); /* Close the device */ -static void - wavelan_detach(struct pcmcia_device *p_dev); /* Destroy a removed device */ - -/**************************** VARIABLES ****************************/ - -/* - * Parameters that can be set with 'insmod' - * The exact syntax is 'insmod wavelan_cs.o <var>=<value>' - */ - -/* Shared memory speed, in ns */ -static int mem_speed = 0; - -/* New module interface */ -module_param(mem_speed, int, 0); - -#ifdef WAVELAN_ROAMING /* Conditional compile, see above in options */ -/* Enable roaming mode ? No ! Please keep this to 0 */ -static int do_roaming = 0; -module_param(do_roaming, bool, 0); -#endif /* WAVELAN_ROAMING */ - -MODULE_LICENSE("GPL"); - -#endif /* WAVELAN_CS_P_H */ - diff --git a/drivers/net/wireless/wl12xx/Kconfig b/drivers/net/wireless/wl12xx/Kconfig index 88060e1..785e024 100644 --- a/drivers/net/wireless/wl12xx/Kconfig +++ b/drivers/net/wireless/wl12xx/Kconfig @@ -1,6 +1,6 @@ menuconfig WL12XX tristate "TI wl12xx driver support" - depends on MAC80211 && WLAN_80211 && EXPERIMENTAL + depends on MAC80211 && EXPERIMENTAL ---help--- This will enable TI wl12xx driver support. The drivers make use of the mac80211 stack. @@ -42,6 +42,7 @@ config WL1251_SDIO config WL1271 tristate "TI wl1271 support" depends on WL12XX && SPI_MASTER && GENERIC_HARDIRQS + depends on INET select FW_LOADER select CRC7 ---help--- diff --git a/drivers/net/wireless/wl12xx/wl1251_main.c b/drivers/net/wireless/wl12xx/wl1251_main.c index 48b0bfd..da3bf1c 100644 --- a/drivers/net/wireless/wl12xx/wl1251_main.c +++ b/drivers/net/wireless/wl12xx/wl1251_main.c @@ -1311,7 +1311,8 @@ int wl1251_init_ieee80211(struct wl1251 *wl) wl->hw->channel_change_time = 10000; wl->hw->flags = IEEE80211_HW_SIGNAL_DBM | - IEEE80211_HW_NOISE_DBM; + IEEE80211_HW_NOISE_DBM | + IEEE80211_HW_SUPPORTS_PS; wl->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION); wl->hw->wiphy->max_scan_ssids = 1; diff --git a/drivers/net/wireless/wl12xx/wl1271.h b/drivers/net/wireless/wl12xx/wl1271.h index 566f152..94359b1 100644 --- a/drivers/net/wireless/wl12xx/wl1271.h +++ b/drivers/net/wireless/wl12xx/wl1271.h @@ -417,6 +417,9 @@ struct wl1271 { /* PSM mode requested */ bool psm_requested; + /* retry counter for PSM entries */ + u8 psm_entry_retry; + /* in dBm */ int power_level; diff --git a/drivers/net/wireless/wl12xx/wl1271_acx.c b/drivers/net/wireless/wl12xx/wl1271_acx.c index bf5a868..5cc89bb 100644 --- a/drivers/net/wireless/wl12xx/wl1271_acx.c +++ b/drivers/net/wireless/wl12xx/wl1271_acx.c @@ -141,7 +141,7 @@ int wl1271_acx_tx_power(struct wl1271 *wl, int power) * calibration, to avoid distortions */ /* acx->current_tx_power = power * 10; */ - acx->current_tx_power = 70; + acx->current_tx_power = 120; ret = wl1271_cmd_configure(wl, DOT11_CUR_TX_PWR, acx, sizeof(*acx)); if (ret < 0) { diff --git a/drivers/net/wireless/wl12xx/wl1271_boot.c b/drivers/net/wireless/wl12xx/wl1271_boot.c index ba4a2b4..b7c9645 100644 --- a/drivers/net/wireless/wl12xx/wl1271_boot.c +++ b/drivers/net/wireless/wl12xx/wl1271_boot.c @@ -380,7 +380,7 @@ static int wl1271_boot_run_firmware(struct wl1271 *wl) } } - if (loop >= INIT_LOOP) { + if (loop > INIT_LOOP) { wl1271_error("timeout waiting for the hardware to " "complete initialization"); return -EIO; @@ -407,7 +407,8 @@ static int wl1271_boot_run_firmware(struct wl1271 *wl) /* unmask required mbox events */ wl->event_mask = BSS_LOSE_EVENT_ID | - SCAN_COMPLETE_EVENT_ID; + SCAN_COMPLETE_EVENT_ID | + PS_REPORT_EVENT_ID; ret = wl1271_event_unmask(wl); if (ret < 0) { diff --git a/drivers/net/wireless/wl12xx/wl1271_cmd.c b/drivers/net/wireless/wl12xx/wl1271_cmd.c index 0666328..990eb01 100644 --- a/drivers/net/wireless/wl12xx/wl1271_cmd.c +++ b/drivers/net/wireless/wl12xx/wl1271_cmd.c @@ -42,12 +42,14 @@ * @buf: buffer containing the command, must work with dma * @len: length of the buffer */ -int wl1271_cmd_send(struct wl1271 *wl, u16 id, void *buf, size_t len) +int wl1271_cmd_send(struct wl1271 *wl, u16 id, void *buf, size_t len, + size_t res_len) { struct wl1271_cmd_header *cmd; unsigned long timeout; u32 intr; int ret = 0; + u16 status; cmd = buf; cmd->id = cpu_to_le16(id); @@ -74,6 +76,17 @@ int wl1271_cmd_send(struct wl1271 *wl, u16 id, void *buf, size_t len) intr = wl1271_spi_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR); } + /* read back the status code of the command */ + if (res_len == 0) + res_len = sizeof(struct wl1271_cmd_header); + wl1271_spi_read(wl, wl->cmd_box_addr, cmd, res_len, false); + + status = le16_to_cpu(cmd->status); + if (status != CMD_STATUS_SUCCESS) { + wl1271_error("command execute failure %d", status); + ret = -EIO; + } + wl1271_spi_write32(wl, ACX_REG_INTERRUPT_ACK, WL1271_ACX_INTR_CMD_COMPLETE); @@ -262,7 +275,7 @@ int wl1271_cmd_join(struct wl1271 *wl) wl->tx_security_seq_16 = 0; wl->tx_security_seq_32 = 0; - ret = wl1271_cmd_send(wl, CMD_START_JOIN, join, sizeof(*join)); + ret = wl1271_cmd_send(wl, CMD_START_JOIN, join, sizeof(*join), 0); if (ret < 0) { wl1271_error("failed to initiate cmd join"); goto out_free; @@ -294,35 +307,21 @@ out: int wl1271_cmd_test(struct wl1271 *wl, void *buf, size_t buf_len, u8 answer) { int ret; + size_t res_len = 0; wl1271_debug(DEBUG_CMD, "cmd test"); - ret = wl1271_cmd_send(wl, CMD_TEST, buf, buf_len); + if (answer) + res_len = buf_len; + + ret = wl1271_cmd_send(wl, CMD_TEST, buf, buf_len, res_len); if (ret < 0) { wl1271_warning("TEST command failed"); return ret; } - if (answer) { - struct wl1271_command *cmd_answer; - u16 status; - - /* - * The test command got in, we can read the answer. - * The answer would be a wl1271_command, where the - * parameter array contains the actual answer. - */ - wl1271_spi_read(wl, wl->cmd_box_addr, buf, buf_len, false); - - cmd_answer = buf; - status = le16_to_cpu(cmd_answer->header.status); - - if (status != CMD_STATUS_SUCCESS) - wl1271_error("TEST command answer error: %d", status); - } - - return 0; + return ret; } /** @@ -345,21 +344,10 @@ int wl1271_cmd_interrogate(struct wl1271 *wl, u16 id, void *buf, size_t len) /* payload length, does not include any headers */ acx->len = cpu_to_le16(len - sizeof(*acx)); - ret = wl1271_cmd_send(wl, CMD_INTERROGATE, acx, sizeof(*acx)); - if (ret < 0) { + ret = wl1271_cmd_send(wl, CMD_INTERROGATE, acx, sizeof(*acx), len); + if (ret < 0) wl1271_error("INTERROGATE command failed"); - goto out; - } - /* the interrogate command got in, we can read the answer */ - wl1271_spi_read(wl, wl->cmd_box_addr, buf, len, false); - - acx = buf; - if (le16_to_cpu(acx->cmd.status) != CMD_STATUS_SUCCESS) - wl1271_error("INTERROGATE command error: %d", - le16_to_cpu(acx->cmd.status)); - -out: return ret; } @@ -383,7 +371,7 @@ int wl1271_cmd_configure(struct wl1271 *wl, u16 id, void *buf, size_t len) /* payload length, does not include any headers */ acx->len = cpu_to_le16(len - sizeof(*acx)); - ret = wl1271_cmd_send(wl, CMD_CONFIGURE, acx, len); + ret = wl1271_cmd_send(wl, CMD_CONFIGURE, acx, len, 0); if (ret < 0) { wl1271_warning("CONFIGURE command NOK"); return ret; @@ -416,7 +404,7 @@ int wl1271_cmd_data_path(struct wl1271 *wl, u8 channel, bool enable) cmd_tx = CMD_DISABLE_TX; } - ret = wl1271_cmd_send(wl, cmd_rx, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, cmd_rx, cmd, sizeof(*cmd), 0); if (ret < 0) { wl1271_error("rx %s cmd for channel %d failed", enable ? "start" : "stop", channel); @@ -426,7 +414,7 @@ int wl1271_cmd_data_path(struct wl1271 *wl, u8 channel, bool enable) wl1271_debug(DEBUG_BOOT, "rx %s cmd channel %d", enable ? "start" : "stop", channel); - ret = wl1271_cmd_send(wl, cmd_tx, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, cmd_tx, cmd, sizeof(*cmd), 0); if (ret < 0) { wl1271_error("tx %s cmd for channel %d failed", enable ? "start" : "stop", channel); @@ -468,7 +456,7 @@ int wl1271_cmd_ps_mode(struct wl1271 *wl, u8 ps_mode) ps_params->null_data_rate = cpu_to_le32(1); /* 1 Mbps */ ret = wl1271_cmd_send(wl, CMD_SET_PS_MODE, ps_params, - sizeof(*ps_params)); + sizeof(*ps_params), 0); if (ret < 0) { wl1271_error("cmd set_ps_mode failed"); goto out; @@ -499,19 +487,14 @@ int wl1271_cmd_read_memory(struct wl1271 *wl, u32 addr, void *answer, cmd->addr = cpu_to_le32(addr); cmd->size = cpu_to_le32(len); - ret = wl1271_cmd_send(wl, CMD_READ_MEMORY, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, CMD_READ_MEMORY, cmd, sizeof(*cmd), + sizeof(*cmd)); if (ret < 0) { wl1271_error("read memory command failed: %d", ret); goto out; } - /* the read command got in, we can now read the answer */ - wl1271_spi_read(wl, wl->cmd_box_addr, cmd, sizeof(*cmd), false); - - if (le16_to_cpu(cmd->header.status) != CMD_STATUS_SUCCESS) - wl1271_error("error in read command result: %d", - le16_to_cpu(cmd->header.status)); - + /* the read command got in */ memcpy(answer, cmd->value, len); out: @@ -613,7 +596,7 @@ int wl1271_cmd_scan(struct wl1271 *wl, u8 *ssid, size_t len, trigger->timeout = 0; ret = wl1271_cmd_send(wl, CMD_TRIGGER_SCAN_TO, trigger, - sizeof(*trigger)); + sizeof(*trigger), 0); if (ret < 0) { wl1271_error("trigger scan to failed for hw scan"); goto out; @@ -636,20 +619,10 @@ int wl1271_cmd_scan(struct wl1271 *wl, u8 *ssid, size_t len, } } - ret = wl1271_cmd_send(wl, CMD_SCAN, params, sizeof(*params)); + ret = wl1271_cmd_send(wl, CMD_SCAN, params, sizeof(*params), 0); if (ret < 0) { wl1271_error("SCAN failed"); - goto out; - } - - wl1271_spi_read(wl, wl->cmd_box_addr, params, sizeof(*params), - false); - - if (le16_to_cpu(params->header.status) != CMD_STATUS_SUCCESS) { - wl1271_error("Scan command error: %d", - le16_to_cpu(params->header.status)); wl->scanning = false; - ret = -EIO; goto out; } @@ -684,7 +657,7 @@ int wl1271_cmd_template_set(struct wl1271 *wl, u16 template_id, if (buf) memcpy(cmd->template_data, buf, buf_len); - ret = wl1271_cmd_send(wl, CMD_SET_TEMPLATE, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, CMD_SET_TEMPLATE, cmd, sizeof(*cmd), 0); if (ret < 0) { wl1271_warning("cmd set_template failed: %d", ret); goto out_free; @@ -863,7 +836,7 @@ int wl1271_cmd_set_default_wep_key(struct wl1271 *wl, u8 id) cmd->key_action = cpu_to_le16(KEY_SET_ID); cmd->key_type = KEY_WEP; - ret = wl1271_cmd_send(wl, CMD_SET_KEYS, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, CMD_SET_KEYS, cmd, sizeof(*cmd), 0); if (ret < 0) { wl1271_warning("cmd set_default_wep_key failed: %d", ret); goto out; @@ -920,7 +893,7 @@ int wl1271_cmd_set_key(struct wl1271 *wl, u16 action, u8 id, u8 key_type, wl1271_dump(DEBUG_CRYPT, "TARGET KEY: ", cmd, sizeof(*cmd)); - ret = wl1271_cmd_send(wl, CMD_SET_KEYS, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, CMD_SET_KEYS, cmd, sizeof(*cmd), 0); if (ret < 0) { wl1271_warning("could not set keys"); goto out; @@ -950,7 +923,7 @@ int wl1271_cmd_disconnect(struct wl1271 *wl) /* disconnect reason is not used in immediate disconnections */ cmd->type = DISCONNECT_IMMEDIATE; - ret = wl1271_cmd_send(wl, CMD_DISCONNECT, cmd, sizeof(*cmd)); + ret = wl1271_cmd_send(wl, CMD_DISCONNECT, cmd, sizeof(*cmd), 0); if (ret < 0) { wl1271_error("failed to send disconnect command"); goto out_free; diff --git a/drivers/net/wireless/wl12xx/wl1271_cmd.h b/drivers/net/wireless/wl12xx/wl1271_cmd.h index 174b820..9d7061b 100644 --- a/drivers/net/wireless/wl12xx/wl1271_cmd.h +++ b/drivers/net/wireless/wl12xx/wl1271_cmd.h @@ -29,7 +29,8 @@ struct acx_header; -int wl1271_cmd_send(struct wl1271 *wl, u16 type, void *buf, size_t buf_len); +int wl1271_cmd_send(struct wl1271 *wl, u16 id, void *buf, size_t len, + size_t res_len); int wl1271_cmd_join(struct wl1271 *wl); int wl1271_cmd_test(struct wl1271 *wl, void *buf, size_t buf_len, u8 answer); int wl1271_cmd_interrogate(struct wl1271 *wl, u16 id, void *buf, size_t len); diff --git a/drivers/net/wireless/wl12xx/wl1271_conf.h b/drivers/net/wireless/wl12xx/wl1271_conf.h index 061d475..565373e 100644 --- a/drivers/net/wireless/wl12xx/wl1271_conf.h +++ b/drivers/net/wireless/wl12xx/wl1271_conf.h @@ -712,6 +712,14 @@ struct conf_conn_settings { * Range 0 - 255 */ u8 bet_max_consecutive; + + /* + * Specifies the maximum number of times to try PSM entry if it fails + * (if sending the appropriate null-func message fails.) + * + * Range 0 - 255 + */ + u8 psm_entry_retries; }; #define CONF_SR_ERR_TBL_MAX_VALUES 14 diff --git a/drivers/net/wireless/wl12xx/wl1271_event.c b/drivers/net/wireless/wl12xx/wl1271_event.c index 31d396b..e135d89 100644 --- a/drivers/net/wireless/wl12xx/wl1271_event.c +++ b/drivers/net/wireless/wl12xx/wl1271_event.c @@ -68,6 +68,40 @@ static int wl1271_event_scan_complete(struct wl1271 *wl, return 0; } +static int wl1271_event_ps_report(struct wl1271 *wl, + struct event_mailbox *mbox, + bool *beacon_loss) +{ + int ret = 0; + + wl1271_debug(DEBUG_EVENT, "ps_status: 0x%x", mbox->ps_status); + + switch (mbox->ps_status) { + case EVENT_ENTER_POWER_SAVE_FAIL: + if (wl->psm_entry_retry < wl->conf.conn.psm_entry_retries) { + wl->psm_entry_retry++; + wl1271_error("PSM entry failed, retrying %d\n", + wl->psm_entry_retry); + ret = wl1271_ps_set_mode(wl, STATION_POWER_SAVE_MODE); + } else { + wl->psm_entry_retry = 0; + *beacon_loss = true; + } + break; + case EVENT_ENTER_POWER_SAVE_SUCCESS: + wl->psm_entry_retry = 0; + break; + case EVENT_EXIT_POWER_SAVE_FAIL: + wl1271_info("PSM exit failed"); + break; + case EVENT_EXIT_POWER_SAVE_SUCCESS: + default: + break; + } + + return ret; +} + static void wl1271_event_mbox_dump(struct event_mailbox *mbox) { wl1271_debug(DEBUG_EVENT, "MBOX DUMP:"); @@ -79,6 +113,7 @@ static int wl1271_event_process(struct wl1271 *wl, struct event_mailbox *mbox) { int ret; u32 vector; + bool beacon_loss = false; wl1271_event_mbox_dump(mbox); @@ -101,7 +136,25 @@ static int wl1271_event_process(struct wl1271 *wl, struct event_mailbox *mbox) wl1271_debug(DEBUG_EVENT, "BSS_LOSE_EVENT"); /* indicate to the stack, that beacons have been lost */ + beacon_loss = true; + } + + if (vector & PS_REPORT_EVENT_ID) { + wl1271_debug(DEBUG_EVENT, "PS_REPORT_EVENT"); + ret = wl1271_event_ps_report(wl, mbox, &beacon_loss); + if (ret < 0) + return ret; + } + + if (beacon_loss) { + /* Obviously, it's dangerous to release the mutex while + we are holding many of the variables in the wl struct. + That's why it's done last in the function, and care must + be taken that nothing more is done after this function + returns. */ + mutex_unlock(&wl->mutex); ieee80211_beacon_loss(wl->vif); + mutex_lock(&wl->mutex); } return 0; diff --git a/drivers/net/wireless/wl12xx/wl1271_event.h b/drivers/net/wireless/wl12xx/wl1271_event.h index 3ab53d3..4e3f55e 100644 --- a/drivers/net/wireless/wl12xx/wl1271_event.h +++ b/drivers/net/wireless/wl12xx/wl1271_event.h @@ -63,6 +63,13 @@ enum { EVENT_MBOX_ALL_EVENT_ID = 0x7fffffff, }; +enum { + EVENT_ENTER_POWER_SAVE_FAIL = 0, + EVENT_ENTER_POWER_SAVE_SUCCESS, + EVENT_EXIT_POWER_SAVE_FAIL, + EVENT_EXIT_POWER_SAVE_SUCCESS, +}; + struct event_debug_report { u8 debug_event_id; u8 num_params; diff --git a/drivers/net/wireless/wl12xx/wl1271_init.c b/drivers/net/wireless/wl12xx/wl1271_init.c index 417b415..7c2017f 100644 --- a/drivers/net/wireless/wl12xx/wl1271_init.c +++ b/drivers/net/wireless/wl12xx/wl1271_init.c @@ -303,12 +303,15 @@ int wl1271_hw_init(struct wl1271 *wl) { int ret; + /* FIXME: the following parameter setting functions return error + * codes - the reason is so far unknown. The -EIO is therefore + * ignored for the time being. */ ret = wl1271_init_general_parms(wl); - if (ret < 0) + if (ret < 0 && ret != -EIO) return ret; ret = wl1271_init_radio_parms(wl); - if (ret < 0) + if (ret < 0 && ret != -EIO) return ret; /* Template settings */ diff --git a/drivers/net/wireless/wl12xx/wl1271_main.c b/drivers/net/wireless/wl12xx/wl1271_main.c index 86132bb..d2149fc 100644 --- a/drivers/net/wireless/wl12xx/wl1271_main.c +++ b/drivers/net/wireless/wl12xx/wl1271_main.c @@ -222,7 +222,8 @@ static struct conf_drv_settings default_conf = { .snr_pkt_avg_weight = 10 }, .bet_enable = CONF_BET_MODE_ENABLE, - .bet_max_consecutive = 100 + .bet_max_consecutive = 100, + .psm_entry_retries = 3 }, .init = { .sr_err_tbl = { @@ -973,6 +974,7 @@ static void wl1271_op_stop(struct ieee80211_hw *hw) wl->rx_counter = 0; wl->elp = false; wl->psm = 0; + wl->psm_entry_retry = 0; wl->tx_queue_stopped = false; wl->power_level = WL1271_DEFAULT_POWER_LEVEL; wl->tx_blocks_available = 0; @@ -1067,11 +1069,11 @@ static int wl1271_op_config_interface(struct ieee80211_hw *hw, ret = wl1271_cmd_join(wl); if (ret < 0) goto out_sleep; - } - ret = wl1271_cmd_build_null_data(wl); - if (ret < 0) - goto out_sleep; + ret = wl1271_cmd_build_null_data(wl); + if (ret < 0) + goto out_sleep; + } wl->ssid_len = conf->ssid_len; if (wl->ssid_len) @@ -1137,10 +1139,6 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed) wl->channel = channel; } - ret = wl1271_cmd_build_null_data(wl); - if (ret < 0) - goto out_sleep; - if (conf->flags & IEEE80211_CONF_PS && !wl->psm_requested) { wl1271_info("psm enabled"); @@ -1165,7 +1163,7 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed) if (conf->power_level != wl->power_level) { ret = wl1271_acx_tx_power(wl, conf->power_level); if (ret < 0) - goto out; + goto out_sleep; wl->power_level = conf->power_level; } @@ -1826,6 +1824,7 @@ static int __devinit wl1271_probe(struct spi_device *spi) wl->elp = false; wl->psm = 0; wl->psm_requested = false; + wl->psm_entry_retry = 0; wl->tx_queue_stopped = false; wl->power_level = WL1271_DEFAULT_POWER_LEVEL; wl->basic_rate_set = WL1271_DEFAULT_BASIC_RATE_SET; diff --git a/drivers/net/wireless/wl12xx/wl1271_rx.c b/drivers/net/wireless/wl12xx/wl1271_rx.c index 37d81ab..ca645f3 100644 --- a/drivers/net/wireless/wl12xx/wl1271_rx.c +++ b/drivers/net/wireless/wl12xx/wl1271_rx.c @@ -159,7 +159,7 @@ static void wl1271_rx_handle_data(struct wl1271 *wl, u32 length) u8 *buf; u8 beacon = 0; - skb = dev_alloc_skb(length); + skb = __dev_alloc_skb(length, GFP_KERNEL); if (!skb) { wl1271_error("Couldn't allocate RX frame"); return; diff --git a/drivers/net/wireless/zd1211rw/Kconfig b/drivers/net/wireless/zd1211rw/Kconfig index 74b31ea..5f80969 100644 --- a/drivers/net/wireless/zd1211rw/Kconfig +++ b/drivers/net/wireless/zd1211rw/Kconfig @@ -1,6 +1,6 @@ config ZD1211RW tristate "ZyDAS ZD1211/ZD1211B USB-wireless support" - depends on USB && MAC80211 && WLAN_80211 && EXPERIMENTAL + depends on USB && MAC80211 && EXPERIMENTAL select FW_LOADER ---help--- This is an experimental driver for the ZyDAS ZD1211/ZD1211B wireless |