diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/8250_pci.c | 159 |
1 files changed, 159 insertions, 0 deletions
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c index 5e48587..fd76542 100644 --- a/drivers/serial/8250_pci.c +++ b/drivers/serial/8250_pci.c @@ -580,6 +580,138 @@ static int pci_netmos_init(struct pci_dev *dev) return num_serial; } +/* + * ITE support by Niels de Vos <niels.devos@wincor-nixdorf.com> + * + * These chips are available with optionally one parallel port and up to + * two serial ports. Unfortunately they all have the same product id. + * + * Basic configuration is done over a region of 32 I/O ports. The base + * ioport is called INTA or INTC, depending on docs/other drivers. + * + * The region of the 32 I/O ports is configured in POSIO0R... + */ + +/* registers */ +#define ITE_887x_MISCR 0x9c +#define ITE_887x_INTCBAR 0x78 +#define ITE_887x_UARTBAR 0x7c +#define ITE_887x_PS0BAR 0x10 +#define ITE_887x_POSIO0 0x60 + +/* I/O space size */ +#define ITE_887x_IOSIZE 32 +/* I/O space size (bits 26-24; 8 bytes = 011b) */ +#define ITE_887x_POSIO_IOSIZE_8 (3 << 24) +/* I/O space size (bits 26-24; 32 bytes = 101b) */ +#define ITE_887x_POSIO_IOSIZE_32 (5 << 24) +/* Decoding speed (1 = slow, 2 = medium, 3 = fast) */ +#define ITE_887x_POSIO_SPEED (3 << 29) +/* enable IO_Space bit */ +#define ITE_887x_POSIO_ENABLE (1 << 31) + +static int __devinit pci_ite887x_init(struct pci_dev *dev) +{ + /* inta_addr are the configuration addresses of the ITE */ + static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0, + 0x200, 0x280, 0 }; + int ret, i, type; + struct resource *iobase = NULL; + u32 miscr, uartbar, ioport; + + /* search for the base-ioport */ + i = 0; + while (inta_addr[i] && iobase == NULL) { + iobase = request_region(inta_addr[i], ITE_887x_IOSIZE, + "ite887x"); + if (iobase != NULL) { + /* write POSIO0R - speed | size | ioport */ + pci_write_config_dword(dev, ITE_887x_POSIO0, + ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED | + ITE_887x_POSIO_IOSIZE_32 | inta_addr[i]); + /* write INTCBAR - ioport */ + pci_write_config_dword(dev, ITE_887x_INTCBAR, inta_addr[i]); + ret = inb(inta_addr[i]); + if (ret != 0xff) { + /* ioport connected */ + break; + } + release_region(iobase->start, ITE_887x_IOSIZE); + iobase = NULL; + } + i++; + } + + if (!inta_addr[i]) { + printk(KERN_ERR "ite887x: could not find iobase\n"); + return -ENODEV; + } + + /* start of undocumented type checking (see parport_pc.c) */ + type = inb(iobase->start + 0x18) & 0x0f; + + switch (type) { + case 0x2: /* ITE8871 (1P) */ + case 0xa: /* ITE8875 (1P) */ + ret = 0; + break; + case 0xe: /* ITE8872 (2S1P) */ + ret = 2; + break; + case 0x6: /* ITE8873 (1S) */ + ret = 1; + break; + case 0x8: /* ITE8874 (2S) */ + ret = 2; + break; + default: + moan_device("Unknown ITE887x", dev); + ret = -ENODEV; + } + + /* configure all serial ports */ + for (i = 0; i < ret; i++) { + /* read the I/O port from the device */ + pci_read_config_dword(dev, ITE_887x_PS0BAR + (0x4 * (i + 1)), + &ioport); + ioport &= 0x0000FF00; /* the actual base address */ + pci_write_config_dword(dev, ITE_887x_POSIO0 + (0x4 * (i + 1)), + ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED | + ITE_887x_POSIO_IOSIZE_8 | ioport); + + /* write the ioport to the UARTBAR */ + pci_read_config_dword(dev, ITE_887x_UARTBAR, &uartbar); + uartbar &= ~(0xffff << (16 * i)); /* clear half the reg */ + uartbar |= (ioport << (16 * i)); /* set the ioport */ + pci_write_config_dword(dev, ITE_887x_UARTBAR, uartbar); + + /* get current config */ + pci_read_config_dword(dev, ITE_887x_MISCR, &miscr); + /* disable interrupts (UARTx_Routing[3:0]) */ + miscr &= ~(0xf << (12 - 4 * i)); + /* activate the UART (UARTx_En) */ + miscr |= 1 << (23 - i); + /* write new config with activated UART */ + pci_write_config_dword(dev, ITE_887x_MISCR, miscr); + } + + if (ret <= 0) { + /* the device has no UARTs if we get here */ + release_region(iobase->start, ITE_887x_IOSIZE); + } + + return ret; +} + +static void __devexit pci_ite887x_exit(struct pci_dev *dev) +{ + u32 ioport; + /* the ioport is bit 0-15 in POSIO0R */ + pci_read_config_dword(dev, ITE_887x_POSIO0, &ioport); + ioport &= 0xffff; + release_region(ioport, ITE_887x_IOSIZE); +} + static int pci_default_setup(struct serial_private *priv, struct pciserial_board *board, struct uart_port *port, int idx) @@ -653,6 +785,18 @@ static struct pci_serial_quirk pci_serial_quirks[] = { .setup = pci_default_setup, }, /* + * ITE + */ + { + .vendor = PCI_VENDOR_ID_ITE, + .device = PCI_DEVICE_ID_ITE_8872, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .init = pci_ite887x_init, + .setup = pci_default_setup, + .exit = __devexit_p(pci_ite887x_exit), + }, + /* * Panacom */ { @@ -933,6 +1077,7 @@ enum pci_board_num_t { pbn_b1_2_1250000, + pbn_b1_bt_1_115200, pbn_b1_bt_2_921600, pbn_b1_1_1382400, @@ -1211,6 +1356,13 @@ static struct pciserial_board pci_boards[] __devinitdata = { .uart_offset = 8, }, + [pbn_b1_bt_1_115200] = { + .flags = FL_BASE1|FL_BASE_BARS, + .num_ports = 1, + .base_baud = 115200, + .uart_offset = 8, + }, + [pbn_b1_bt_2_921600] = { .flags = FL_BASE1|FL_BASE_BARS, .num_ports = 2, @@ -2364,6 +2516,13 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_1_115200 }, + /* + * ITE + */ + { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, + pbn_b1_bt_1_115200 }, /* * IntaShield IS-200 |