diff options
Diffstat (limited to 'include/asm-arm/hardware/sa1111.h')
| -rw-r--r-- | include/asm-arm/hardware/sa1111.h | 581 |
1 files changed, 0 insertions, 581 deletions
diff --git a/include/asm-arm/hardware/sa1111.h b/include/asm-arm/hardware/sa1111.h deleted file mode 100644 index 61b1d05..0000000 --- a/include/asm-arm/hardware/sa1111.h +++ /dev/null @@ -1,581 +0,0 @@ -/* - * linux/include/asm-arm/hardware/sa1111.h - * - * Copyright (C) 2000 John G Dorsey <john+@cs.cmu.edu> - * - * This file contains definitions for the SA-1111 Companion Chip. - * (Structure and naming borrowed from SA-1101.h, by Peter Danielsson.) - * - * Macro that calculates real address for registers in the SA-1111 - */ - -#ifndef _ASM_ARCH_SA1111 -#define _ASM_ARCH_SA1111 - -#include <asm/arch/bitfield.h> - -/* - * The SA1111 is always located at virtual 0xf4000000, and is always - * "native" endian. - */ - -#define SA1111_VBASE 0xf4000000 - -/* Don't use these! */ -#define SA1111_p2v( x ) ((x) - SA1111_BASE + SA1111_VBASE) -#define SA1111_v2p( x ) ((x) - SA1111_VBASE + SA1111_BASE) - -#ifndef __ASSEMBLY__ -#define _SA1111(x) ((x) + sa1111->resource.start) -#endif - -#define sa1111_writel(val,addr) __raw_writel(val, addr) -#define sa1111_readl(addr) __raw_readl(addr) - -/* - * 26 bits of the SA-1110 address bus are available to the SA-1111. - * Use these when feeding target addresses to the DMA engines. - */ - -#define SA1111_ADDR_WIDTH (26) -#define SA1111_ADDR_MASK ((1<<SA1111_ADDR_WIDTH)-1) -#define SA1111_DMA_ADDR(x) ((x)&SA1111_ADDR_MASK) - -/* - * Don't ask the (SAC) DMA engines to move less than this amount. - */ - -#define SA1111_SAC_DMA_MIN_XFER (0x800) - -/* - * System Bus Interface (SBI) - * - * Registers - * SKCR Control Register - * SMCR Shared Memory Controller Register - * SKID ID Register - */ -#define SA1111_SKCR 0x0000 -#define SA1111_SMCR 0x0004 -#define SA1111_SKID 0x0008 - -#define SKCR_PLL_BYPASS (1<<0) -#define SKCR_RCLKEN (1<<1) -#define SKCR_SLEEP (1<<2) -#define SKCR_DOZE (1<<3) -#define SKCR_VCO_OFF (1<<4) -#define SKCR_SCANTSTEN (1<<5) -#define SKCR_CLKTSTEN (1<<6) -#define SKCR_RDYEN (1<<7) -#define SKCR_SELAC (1<<8) -#define SKCR_OPPC (1<<9) -#define SKCR_PLLTSTEN (1<<10) -#define SKCR_USBIOTSTEN (1<<11) -/* - * Don't believe the specs! Take them, throw them outside. Leave them - * there for a week. Spit on them. Walk on them. Stamp on them. - * Pour gasoline over them and finally burn them. Now think about coding. - * - The October 1999 errata (278260-007) says its bit 13, 1 to enable. - * - The Feb 2001 errata (278260-010) says that the previous errata - * (278260-009) is wrong, and its bit actually 12, fixed in spec - * 278242-003. - * - The SA1111 manual (278242) says bit 12, but 0 to enable. - * - Reality is bit 13, 1 to enable. - * -- rmk - */ -#define SKCR_OE_EN (1<<13) - -#define SMCR_DTIM (1<<0) -#define SMCR_MBGE (1<<1) -#define SMCR_DRAC_0 (1<<2) -#define SMCR_DRAC_1 (1<<3) -#define SMCR_DRAC_2 (1<<4) -#define SMCR_DRAC Fld(3, 2) -#define SMCR_CLAT (1<<5) - -#define SKID_SIREV_MASK (0x000000f0) -#define SKID_MTREV_MASK (0x0000000f) -#define SKID_ID_MASK (0xffffff00) -#define SKID_SA1111_ID (0x690cc200) - -/* - * System Controller - * - * Registers - * SKPCR Power Control Register - * SKCDR Clock Divider Register - * SKAUD Audio Clock Divider Register - * SKPMC PS/2 Mouse Clock Divider Register - * SKPTC PS/2 Track Pad Clock Divider Register - * SKPEN0 PWM0 Enable Register - * SKPWM0 PWM0 Clock Register - * SKPEN1 PWM1 Enable Register - * SKPWM1 PWM1 Clock Register - */ -#define SA1111_SKPCR 0x0200 -#define SA1111_SKCDR 0x0204 -#define SA1111_SKAUD 0x0208 -#define SA1111_SKPMC 0x020c -#define SA1111_SKPTC 0x0210 -#define SA1111_SKPEN0 0x0214 -#define SA1111_SKPWM0 0x0218 -#define SA1111_SKPEN1 0x021c -#define SA1111_SKPWM1 0x0220 - -#define SKPCR_UCLKEN (1<<0) -#define SKPCR_ACCLKEN (1<<1) -#define SKPCR_I2SCLKEN (1<<2) -#define SKPCR_L3CLKEN (1<<3) -#define SKPCR_SCLKEN (1<<4) -#define SKPCR_PMCLKEN (1<<5) -#define SKPCR_PTCLKEN (1<<6) -#define SKPCR_DCLKEN (1<<7) -#define SKPCR_PWMCLKEN (1<<8) - -/* - * USB Host controller - */ -#define SA1111_USB 0x0400 - -/* - * Offsets from SA1111_USB_BASE - */ -#define SA1111_USB_STATUS 0x0118 -#define SA1111_USB_RESET 0x011c -#define SA1111_USB_IRQTEST 0x0120 - -#define USB_RESET_FORCEIFRESET (1 << 0) -#define USB_RESET_FORCEHCRESET (1 << 1) -#define USB_RESET_CLKGENRESET (1 << 2) -#define USB_RESET_SIMSCALEDOWN (1 << 3) -#define USB_RESET_USBINTTEST (1 << 4) -#define USB_RESET_SLEEPSTBYEN (1 << 5) -#define USB_RESET_PWRSENSELOW (1 << 6) -#define USB_RESET_PWRCTRLLOW (1 << 7) - -#define USB_STATUS_IRQHCIRMTWKUP (1 << 7) -#define USB_STATUS_IRQHCIBUFFACC (1 << 8) -#define USB_STATUS_NIRQHCIM (1 << 9) -#define USB_STATUS_NHCIMFCLR (1 << 10) -#define USB_STATUS_USBPWRSENSE (1 << 11) - -/* - * Serial Audio Controller - * - * Registers - * SACR0 Serial Audio Common Control Register - * SACR1 Serial Audio Alternate Mode (I2C/MSB) Control Register - * SACR2 Serial Audio AC-link Control Register - * SASR0 Serial Audio I2S/MSB Interface & FIFO Status Register - * SASR1 Serial Audio AC-link Interface & FIFO Status Register - * SASCR Serial Audio Status Clear Register - * L3_CAR L3 Control Bus Address Register - * L3_CDR L3 Control Bus Data Register - * ACCAR AC-link Command Address Register - * ACCDR AC-link Command Data Register - * ACSAR AC-link Status Address Register - * ACSDR AC-link Status Data Register - * SADTCS Serial Audio DMA Transmit Control/Status Register - * SADTSA Serial Audio DMA Transmit Buffer Start Address A - * SADTCA Serial Audio DMA Transmit Buffer Count Register A - * SADTSB Serial Audio DMA Transmit Buffer Start Address B - * SADTCB Serial Audio DMA Transmit Buffer Count Register B - * SADRCS Serial Audio DMA Receive Control/Status Register - * SADRSA Serial Audio DMA Receive Buffer Start Address A - * SADRCA Serial Audio DMA Receive Buffer Count Register A - * SADRSB Serial Audio DMA Receive Buffer Start Address B - * SADRCB Serial Audio DMA Receive Buffer Count Register B - * SAITR Serial Audio Interrupt Test Register - * SADR Serial Audio Data Register (16 x 32-bit) - */ - -#define SA1111_SERAUDIO 0x0600 - -/* - * These are offsets from the above base. - */ -#define SA1111_SACR0 0x00 -#define SA1111_SACR1 0x04 -#define SA1111_SACR2 0x08 -#define SA1111_SASR0 0x0c -#define SA1111_SASR1 0x10 -#define SA1111_SASCR 0x18 -#define SA1111_L3_CAR 0x1c -#define SA1111_L3_CDR 0x20 -#define SA1111_ACCAR 0x24 -#define SA1111_ACCDR 0x28 -#define SA1111_ACSAR 0x2c -#define SA1111_ACSDR 0x30 -#define SA1111_SADTCS 0x34 -#define SA1111_SADTSA 0x38 -#define SA1111_SADTCA 0x3c -#define SA1111_SADTSB 0x40 -#define SA1111_SADTCB 0x44 -#define SA1111_SADRCS 0x48 -#define SA1111_SADRSA 0x4c -#define SA1111_SADRCA 0x50 -#define SA1111_SADRSB 0x54 -#define SA1111_SADRCB 0x58 -#define SA1111_SAITR 0x5c -#define SA1111_SADR 0x80 - -#ifndef CONFIG_ARCH_PXA - -#define SACR0_ENB (1<<0) -#define SACR0_BCKD (1<<2) -#define SACR0_RST (1<<3) - -#define SACR1_AMSL (1<<0) -#define SACR1_L3EN (1<<1) -#define SACR1_L3MB (1<<2) -#define SACR1_DREC (1<<3) -#define SACR1_DRPL (1<<4) -#define SACR1_ENLBF (1<<5) - -#define SACR2_TS3V (1<<0) -#define SACR2_TS4V (1<<1) -#define SACR2_WKUP (1<<2) -#define SACR2_DREC (1<<3) -#define SACR2_DRPL (1<<4) -#define SACR2_ENLBF (1<<5) -#define SACR2_RESET (1<<6) - -#define SASR0_TNF (1<<0) -#define SASR0_RNE (1<<1) -#define SASR0_BSY (1<<2) -#define SASR0_TFS (1<<3) -#define SASR0_RFS (1<<4) -#define SASR0_TUR (1<<5) -#define SASR0_ROR (1<<6) -#define SASR0_L3WD (1<<16) -#define SASR0_L3RD (1<<17) - -#define SASR1_TNF (1<<0) -#define SASR1_RNE (1<<1) -#define SASR1_BSY (1<<2) -#define SASR1_TFS (1<<3) -#define SASR1_RFS (1<<4) -#define SASR1_TUR (1<<5) -#define SASR1_ROR (1<<6) -#define SASR1_CADT (1<<16) -#define SASR1_SADR (1<<17) -#define SASR1_RSTO (1<<18) -#define SASR1_CLPM (1<<19) -#define SASR1_CRDY (1<<20) -#define SASR1_RS3V (1<<21) -#define SASR1_RS4V (1<<22) - -#define SASCR_TUR (1<<5) -#define SASCR_ROR (1<<6) -#define SASCR_DTS (1<<16) -#define SASCR_RDD (1<<17) -#define SASCR_STO (1<<18) - -#define SADTCS_TDEN (1<<0) -#define SADTCS_TDIE (1<<1) -#define SADTCS_TDBDA (1<<3) -#define SADTCS_TDSTA (1<<4) -#define SADTCS_TDBDB (1<<5) -#define SADTCS_TDSTB (1<<6) -#define SADTCS_TBIU (1<<7) - -#define SADRCS_RDEN (1<<0) -#define SADRCS_RDIE (1<<1) -#define SADRCS_RDBDA (1<<3) -#define SADRCS_RDSTA (1<<4) -#define SADRCS_RDBDB (1<<5) -#define SADRCS_RDSTB (1<<6) -#define SADRCS_RBIU (1<<7) - -#define SAD_CS_DEN (1<<0) -#define SAD_CS_DIE (1<<1) /* Not functional on metal 1 */ -#define SAD_CS_DBDA (1<<3) /* Not functional on metal 1 */ -#define SAD_CS_DSTA (1<<4) -#define SAD_CS_DBDB (1<<5) /* Not functional on metal 1 */ -#define SAD_CS_DSTB (1<<6) -#define SAD_CS_BIU (1<<7) /* Not functional on metal 1 */ - -#define SAITR_TFS (1<<0) -#define SAITR_RFS (1<<1) -#define SAITR_TUR (1<<2) -#define SAITR_ROR (1<<3) -#define SAITR_CADT (1<<4) -#define SAITR_SADR (1<<5) -#define SAITR_RSTO (1<<6) -#define SAITR_TDBDA (1<<8) -#define SAITR_TDBDB (1<<9) -#define SAITR_RDBDA (1<<10) -#define SAITR_RDBDB (1<<11) - -#endif /* !CONFIG_ARCH_PXA */ - -/* - * General-Purpose I/O Interface - * - * Registers - * PA_DDR GPIO Block A Data Direction - * PA_DRR/PA_DWR GPIO Block A Data Value Register (read/write) - * PA_SDR GPIO Block A Sleep Direction - * PA_SSR GPIO Block A Sleep State - * PB_DDR GPIO Block B Data Direction - * PB_DRR/PB_DWR GPIO Block B Data Value Register (read/write) - * PB_SDR GPIO Block B Sleep Direction - * PB_SSR GPIO Block B Sleep State - * PC_DDR GPIO Block C Data Direction - * PC_DRR/PC_DWR GPIO Block C Data Value Register (read/write) - * PC_SDR GPIO Block C Sleep Direction - * PC_SSR GPIO Block C Sleep State - */ - -#define _PA_DDR _SA1111( 0x1000 ) -#define _PA_DRR _SA1111( 0x1004 ) -#define _PA_DWR _SA1111( 0x1004 ) -#define _PA_SDR _SA1111( 0x1008 ) -#define _PA_SSR _SA1111( 0x100c ) -#define _PB_DDR _SA1111( 0x1010 ) -#define _PB_DRR _SA1111( 0x1014 ) -#define _PB_DWR _SA1111( 0x1014 ) -#define _PB_SDR _SA1111( 0x1018 ) -#define _PB_SSR _SA1111( 0x101c ) -#define _PC_DDR _SA1111( 0x1020 ) -#define _PC_DRR _SA1111( 0x1024 ) -#define _PC_DWR _SA1111( 0x1024 ) -#define _PC_SDR _SA1111( 0x1028 ) -#define _PC_SSR _SA1111( 0x102c ) - -#define SA1111_GPIO 0x1000 - -#define SA1111_GPIO_PADDR (0x000) -#define SA1111_GPIO_PADRR (0x004) -#define SA1111_GPIO_PADWR (0x004) -#define SA1111_GPIO_PASDR (0x008) -#define SA1111_GPIO_PASSR (0x00c) -#define SA1111_GPIO_PBDDR (0x010) -#define SA1111_GPIO_PBDRR (0x014) -#define SA1111_GPIO_PBDWR (0x014) -#define SA1111_GPIO_PBSDR (0x018) -#define SA1111_GPIO_PBSSR (0x01c) -#define SA1111_GPIO_PCDDR (0x020) -#define SA1111_GPIO_PCDRR (0x024) -#define SA1111_GPIO_PCDWR (0x024) -#define SA1111_GPIO_PCSDR (0x028) -#define SA1111_GPIO_PCSSR (0x02c) - -#define GPIO_A0 (1 << 0) -#define GPIO_A1 (1 << 1) -#define GPIO_A2 (1 << 2) -#define GPIO_A3 (1 << 3) - -#define GPIO_B0 (1 << 8) -#define GPIO_B1 (1 << 9) -#define GPIO_B2 (1 << 10) -#define GPIO_B3 (1 << 11) -#define GPIO_B4 (1 << 12) -#define GPIO_B5 (1 << 13) -#define GPIO_B6 (1 << 14) -#define GPIO_B7 (1 << 15) - -#define GPIO_C0 (1 << 16) -#define GPIO_C1 (1 << 17) -#define GPIO_C2 (1 << 18) -#define GPIO_C3 (1 << 19) -#define GPIO_C4 (1 << 20) -#define GPIO_C5 (1 << 21) -#define GPIO_C6 (1 << 22) -#define GPIO_C7 (1 << 23) - -/* - * Interrupt Controller - * - * Registers - * INTTEST0 Test register 0 - * INTTEST1 Test register 1 - * INTEN0 Interrupt Enable register 0 - * INTEN1 Interrupt Enable register 1 - * INTPOL0 Interrupt Polarity selection 0 - * INTPOL1 Interrupt Polarity selection 1 - * INTTSTSEL Interrupt source selection - * INTSTATCLR0 Interrupt Status/Clear 0 - * INTSTATCLR1 Interrupt Status/Clear 1 - * INTSET0 Interrupt source set 0 - * INTSET1 Interrupt source set 1 - * WAKE_EN0 Wake-up source enable 0 - * WAKE_EN1 Wake-up source enable 1 - * WAKE_POL0 Wake-up polarity selection 0 - * WAKE_POL1 Wake-up polarity selection 1 - */ -#define SA1111_INTC 0x1600 - -/* - * These are offsets from the above base. - */ -#define SA1111_INTTEST0 0x0000 -#define SA1111_INTTEST1 0x0004 -#define SA1111_INTEN0 0x0008 -#define SA1111_INTEN1 0x000c -#define SA1111_INTPOL0 0x0010 -#define SA1111_INTPOL1 0x0014 -#define SA1111_INTTSTSEL 0x0018 -#define SA1111_INTSTATCLR0 0x001c -#define SA1111_INTSTATCLR1 0x0020 -#define SA1111_INTSET0 0x0024 -#define SA1111_INTSET1 0x0028 -#define SA1111_WAKEEN0 0x002c -#define SA1111_WAKEEN1 0x0030 -#define SA1111_WAKEPOL0 0x0034 -#define SA1111_WAKEPOL1 0x0038 - -/* - * PS/2 Trackpad and Mouse Interfaces - * - * Registers - * PS2CR Control Register - * PS2STAT Status Register - * PS2DATA Transmit/Receive Data register - * PS2CLKDIV Clock Division Register - * PS2PRECNT Clock Precount Register - * PS2TEST1 Test register 1 - * PS2TEST2 Test register 2 - * PS2TEST3 Test register 3 - * PS2TEST4 Test register 4 - */ - -#define SA1111_KBD 0x0a00 -#define SA1111_MSE 0x0c00 - -/* - * These are offsets from the above bases. - */ -#define SA1111_PS2CR 0x0000 -#define SA1111_PS2STAT 0x0004 -#define SA1111_PS2DATA 0x0008 -#define SA1111_PS2CLKDIV 0x000c -#define SA1111_PS2PRECNT 0x0010 - -#define PS2CR_ENA 0x08 -#define PS2CR_FKD 0x02 -#define PS2CR_FKC 0x01 - -#define PS2STAT_STP 0x0100 -#define PS2STAT_TXE 0x0080 -#define PS2STAT_TXB 0x0040 -#define PS2STAT_RXF 0x0020 -#define PS2STAT_RXB 0x0010 -#define PS2STAT_ENA 0x0008 -#define PS2STAT_RXP 0x0004 -#define PS2STAT_KBD 0x0002 -#define PS2STAT_KBC 0x0001 - -/* - * PCMCIA Interface - * - * Registers - * PCSR Status Register - * PCCR Control Register - * PCSSR Sleep State Register - */ - -#define SA1111_PCMCIA 0x1600 - -/* - * These are offsets from the above base. - */ -#define SA1111_PCCR 0x0000 -#define SA1111_PCSSR 0x0004 -#define SA1111_PCSR 0x0008 - -#define PCSR_S0_READY (1<<0) -#define PCSR_S1_READY (1<<1) -#define PCSR_S0_DETECT (1<<2) -#define PCSR_S1_DETECT (1<<3) -#define PCSR_S0_VS1 (1<<4) -#define PCSR_S0_VS2 (1<<5) -#define PCSR_S1_VS1 (1<<6) -#define PCSR_S1_VS2 (1<<7) -#define PCSR_S0_WP (1<<8) -#define PCSR_S1_WP (1<<9) -#define PCSR_S0_BVD1 (1<<10) -#define PCSR_S0_BVD2 (1<<11) -#define PCSR_S1_BVD1 (1<<12) -#define PCSR_S1_BVD2 (1<<13) - -#define PCCR_S0_RST (1<<0) -#define PCCR_S1_RST (1<<1) -#define PCCR_S0_FLT (1<<2) -#define PCCR_S1_FLT (1<<3) -#define PCCR_S0_PWAITEN (1<<4) -#define PCCR_S1_PWAITEN (1<<5) -#define PCCR_S0_PSE (1<<6) -#define PCCR_S1_PSE (1<<7) - -#define PCSSR_S0_SLEEP (1<<0) -#define PCSSR_S1_SLEEP (1<<1) - - - - -extern struct bus_type sa1111_bus_type; - -#define SA1111_DEVID_SBI 0 -#define SA1111_DEVID_SK 1 -#define SA1111_DEVID_USB 2 -#define SA1111_DEVID_SAC 3 -#define SA1111_DEVID_SSP 4 -#define SA1111_DEVID_PS2 5 -#define SA1111_DEVID_GPIO 6 -#define SA1111_DEVID_INT 7 -#define SA1111_DEVID_PCMCIA 8 - -struct sa1111_dev { - struct device dev; - unsigned int devid; - struct resource res; - void __iomem *mapbase; - unsigned int skpcr_mask; - unsigned int irq[6]; - u64 dma_mask; -}; - -#define SA1111_DEV(_d) container_of((_d), struct sa1111_dev, dev) - -#define sa1111_get_drvdata(d) dev_get_drvdata(&(d)->dev) -#define sa1111_set_drvdata(d,p) dev_set_drvdata(&(d)->dev, p) - -struct sa1111_driver { - struct device_driver drv; - unsigned int devid; - int (*probe)(struct sa1111_dev *); - int (*remove)(struct sa1111_dev *); - int (*suspend)(struct sa1111_dev *, pm_message_t); - int (*resume)(struct sa1111_dev *); -}; - -#define SA1111_DRV(_d) container_of((_d), struct sa1111_driver, drv) - -#define SA1111_DRIVER_NAME(_sadev) ((_sadev)->dev.driver->name) - -/* - * These frob the SKPCR register. - */ -void sa1111_enable_device(struct sa1111_dev *); -void sa1111_disable_device(struct sa1111_dev *); - -unsigned int sa1111_pll_clock(struct sa1111_dev *); - -#define SA1111_AUDIO_ACLINK 0 -#define SA1111_AUDIO_I2S 1 - -void sa1111_select_audio_mode(struct sa1111_dev *sadev, int mode); -int sa1111_set_audio_rate(struct sa1111_dev *sadev, int rate); -int sa1111_get_audio_rate(struct sa1111_dev *sadev); - -int sa1111_check_dma_bug(dma_addr_t addr); - -int sa1111_driver_register(struct sa1111_driver *); -void sa1111_driver_unregister(struct sa1111_driver *); - -void sa1111_set_io_dir(struct sa1111_dev *sadev, unsigned int bits, unsigned int dir, unsigned int sleep_dir); -void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v); -void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v); - -#endif /* _ASM_ARCH_SA1111 */ |