diff options
Diffstat (limited to 'include/asm-m68knommu/m5249sim.h')
| -rw-r--r-- | include/asm-m68knommu/m5249sim.h | 209 |
1 files changed, 0 insertions, 209 deletions
diff --git a/include/asm-m68knommu/m5249sim.h b/include/asm-m68knommu/m5249sim.h deleted file mode 100644 index 366eb86..0000000 --- a/include/asm-m68knommu/m5249sim.h +++ /dev/null @@ -1,209 +0,0 @@ -/****************************************************************************/ - -/* - * m5249sim.h -- ColdFire 5249 System Integration Module support. - * - * (C) Copyright 2002, Greg Ungerer (gerg@snapgear.com) - */ - -/****************************************************************************/ -#ifndef m5249sim_h -#define m5249sim_h -/****************************************************************************/ - -/* - * Define the 5249 SIM register set addresses. - */ -#define MCFSIM_RSR 0x00 /* Reset Status reg (r/w) */ -#define MCFSIM_SYPCR 0x01 /* System Protection reg (r/w)*/ -#define MCFSIM_SWIVR 0x02 /* SW Watchdog intr reg (r/w) */ -#define MCFSIM_SWSR 0x03 /* SW Watchdog service (r/w) */ -#define MCFSIM_PAR 0x04 /* Pin Assignment reg (r/w) */ -#define MCFSIM_IRQPAR 0x06 /* Interrupt Assignment reg (r/w) */ -#define MCFSIM_MPARK 0x0C /* BUS Master Control Reg*/ -#define MCFSIM_IPR 0x40 /* Interrupt Pend reg (r/w) */ -#define MCFSIM_IMR 0x44 /* Interrupt Mask reg (r/w) */ -#define MCFSIM_AVR 0x4b /* Autovector Ctrl reg (r/w) */ -#define MCFSIM_ICR0 0x4c /* Intr Ctrl reg 0 (r/w) */ -#define MCFSIM_ICR1 0x4d /* Intr Ctrl reg 1 (r/w) */ -#define MCFSIM_ICR2 0x4e /* Intr Ctrl reg 2 (r/w) */ -#define MCFSIM_ICR3 0x4f /* Intr Ctrl reg 3 (r/w) */ -#define MCFSIM_ICR4 0x50 /* Intr Ctrl reg 4 (r/w) */ -#define MCFSIM_ICR5 0x51 /* Intr Ctrl reg 5 (r/w) */ -#define MCFSIM_ICR6 0x52 /* Intr Ctrl reg 6 (r/w) */ -#define MCFSIM_ICR7 0x53 /* Intr Ctrl reg 7 (r/w) */ -#define MCFSIM_ICR8 0x54 /* Intr Ctrl reg 8 (r/w) */ -#define MCFSIM_ICR9 0x55 /* Intr Ctrl reg 9 (r/w) */ -#define MCFSIM_ICR10 0x56 /* Intr Ctrl reg 10 (r/w) */ -#define MCFSIM_ICR11 0x57 /* Intr Ctrl reg 11 (r/w) */ - -#define MCFSIM_CSAR0 0x80 /* CS 0 Address 0 reg (r/w) */ -#define MCFSIM_CSMR0 0x84 /* CS 0 Mask 0 reg (r/w) */ -#define MCFSIM_CSCR0 0x8a /* CS 0 Control reg (r/w) */ -#define MCFSIM_CSAR1 0x8c /* CS 1 Address reg (r/w) */ -#define MCFSIM_CSMR1 0x90 /* CS 1 Mask reg (r/w) */ -#define MCFSIM_CSCR1 0x96 /* CS 1 Control reg (r/w) */ -#define MCFSIM_CSAR2 0x98 /* CS 2 Address reg (r/w) */ -#define MCFSIM_CSMR2 0x9c /* CS 2 Mask reg (r/w) */ -#define MCFSIM_CSCR2 0xa2 /* CS 2 Control reg (r/w) */ -#define MCFSIM_CSAR3 0xa4 /* CS 3 Address reg (r/w) */ -#define MCFSIM_CSMR3 0xa8 /* CS 3 Mask reg (r/w) */ -#define MCFSIM_CSCR3 0xae /* CS 3 Control reg (r/w) */ - -#define MCFSIM_DCR 0x100 /* DRAM Control reg (r/w) */ -#define MCFSIM_DACR0 0x108 /* DRAM 0 Addr and Ctrl (r/w) */ -#define MCFSIM_DMR0 0x10c /* DRAM 0 Mask reg (r/w) */ -#define MCFSIM_DACR1 0x110 /* DRAM 1 Addr and Ctrl (r/w) */ -#define MCFSIM_DMR1 0x114 /* DRAM 1 Mask reg (r/w) */ - - -/* - * Some symbol defines for the above... - */ -#define MCFSIM_SWDICR MCFSIM_ICR0 /* Watchdog timer ICR */ -#define MCFSIM_TIMER1ICR MCFSIM_ICR1 /* Timer 1 ICR */ -#define MCFSIM_TIMER2ICR MCFSIM_ICR2 /* Timer 2 ICR */ -#define MCFSIM_UART1ICR MCFSIM_ICR4 /* UART 1 ICR */ -#define MCFSIM_UART2ICR MCFSIM_ICR5 /* UART 2 ICR */ -#define MCFSIM_DMA0ICR MCFSIM_ICR6 /* DMA 0 ICR */ -#define MCFSIM_DMA1ICR MCFSIM_ICR7 /* DMA 1 ICR */ -#define MCFSIM_DMA2ICR MCFSIM_ICR8 /* DMA 2 ICR */ -#define MCFSIM_DMA3ICR MCFSIM_ICR9 /* DMA 3 ICR */ - -/* - * General purpose IO registers (in MBAR2). - */ -#define MCFSIM2_GPIOREAD 0x0 /* GPIO read values */ -#define MCFSIM2_GPIOWRITE 0x4 /* GPIO write values */ -#define MCFSIM2_GPIOENABLE 0x8 /* GPIO enabled */ -#define MCFSIM2_GPIOFUNC 0xc /* GPIO function */ -#define MCFSIM2_GPIO1READ 0xb0 /* GPIO1 read values */ -#define MCFSIM2_GPIO1WRITE 0xb4 /* GPIO1 write values */ -#define MCFSIM2_GPIO1ENABLE 0xb8 /* GPIO1 enabled */ -#define MCFSIM2_GPIO1FUNC 0xbc /* GPIO1 function */ - -#define MCFSIM2_GPIOINTSTAT 0xc0 /* GPIO interrupt status */ -#define MCFSIM2_GPIOINTCLEAR 0xc0 /* GPIO interrupt clear */ -#define MCFSIM2_GPIOINTENABLE 0xc4 /* GPIO interrupt enable */ - -#define MCFSIM2_INTLEVEL1 0x140 /* Interrupt level reg 1 */ -#define MCFSIM2_INTLEVEL2 0x144 /* Interrupt level reg 2 */ -#define MCFSIM2_INTLEVEL3 0x148 /* Interrupt level reg 3 */ -#define MCFSIM2_INTLEVEL4 0x14c /* Interrupt level reg 4 */ -#define MCFSIM2_INTLEVEL5 0x150 /* Interrupt level reg 5 */ -#define MCFSIM2_INTLEVEL6 0x154 /* Interrupt level reg 6 */ -#define MCFSIM2_INTLEVEL7 0x158 /* Interrupt level reg 7 */ -#define MCFSIM2_INTLEVEL8 0x15c /* Interrupt level reg 8 */ - -#define MCFSIM2_DMAROUTE 0x188 /* DMA routing */ - -#define MCFSIM2_IDECONFIG1 0x18c /* IDEconfig1 */ -#define MCFSIM2_IDECONFIG2 0x190 /* IDEconfig2 */ - - -/* - * Macro to set IMR register. It is 32 bits on the 5249. - */ -#define MCFSIM_IMR_MASKALL 0x7fffe /* All SIM intr sources */ - -#define mcf_getimr() \ - *((volatile unsigned long *) (MCF_MBAR + MCFSIM_IMR)) - -#define mcf_setimr(imr) \ - *((volatile unsigned long *) (MCF_MBAR + MCFSIM_IMR)) = (imr); - -#define mcf_getipr() \ - *((volatile unsigned long *) (MCF_MBAR + MCFSIM_IPR)) - -/****************************************************************************/ - -#ifdef __ASSEMBLER__ - -/* - * The M5249C3 board needs a little help getting all its SIM devices - * initialized at kernel start time. dBUG doesn't set much up, so - * we need to do it manually. - */ -.macro m5249c3_setup - /* - * Set MBAR1 and MBAR2, just incase they are not set. - */ - movel #0x10000001,%a0 - movec %a0,%MBAR /* map MBAR region */ - subql #1,%a0 /* get MBAR address in a0 */ - - movel #0x80000001,%a1 - movec %a1,#3086 /* map MBAR2 region */ - subql #1,%a1 /* get MBAR2 address in a1 */ - - /* - * Move secondary interrupts to base at 128. - */ - moveb #0x80,%d0 - moveb %d0,0x16b(%a1) /* interrupt base register */ - - /* - * Work around broken CSMR0/DRAM vector problem. - */ - movel #0x001F0021,%d0 /* disable C/I bit */ - movel %d0,0x84(%a0) /* set CSMR0 */ - - /* - * Disable the PLL firstly. (Who knows what state it is - * in here!). - */ - movel 0x180(%a1),%d0 /* get current PLL value */ - andl #0xfffffffe,%d0 /* PLL bypass first */ - movel %d0,0x180(%a1) /* set PLL register */ - nop - -#if CONFIG_CLOCK_FREQ == 140000000 - /* - * Set initial clock frequency. This assumes M5249C3 board - * is fitted with 11.2896MHz crystal. It will program the - * PLL for 140MHz. Lets go fast :-) - */ - movel #0x125a40f0,%d0 /* set for 140MHz */ - movel %d0,0x180(%a1) /* set PLL register */ - orl #0x1,%d0 - movel %d0,0x180(%a1) /* set PLL register */ -#endif - - /* - * Setup CS1 for ethernet controller. - * (Setup as per M5249C3 doco). - */ - movel #0xe0000000,%d0 /* CS1 mapped at 0xe0000000 */ - movel %d0,0x8c(%a0) - movel #0x001f0021,%d0 /* CS1 size of 1Mb */ - movel %d0,0x90(%a0) - movew #0x0080,%d0 /* CS1 = 16bit port, AA */ - movew %d0,0x96(%a0) - - /* - * Setup CS2 for IDE interface. - */ - movel #0x50000000,%d0 /* CS2 mapped at 0x50000000 */ - movel %d0,0x98(%a0) - movel #0x001f0001,%d0 /* CS2 size of 1MB */ - movel %d0,0x9c(%a0) - movew #0x0080,%d0 /* CS2 = 16bit, TA */ - movew %d0,0xa2(%a0) - - movel #0x00107000,%d0 /* IDEconfig1 */ - movel %d0,0x18c(%a1) - movel #0x000c0400,%d0 /* IDEconfig2 */ - movel %d0,0x190(%a1) - - movel #0x00080000,%d0 /* GPIO19, IDE reset bit */ - orl %d0,0xc(%a1) /* function GPIO19 */ - orl %d0,0x8(%a1) /* enable GPIO19 as output */ - orl %d0,0x4(%a1) /* de-assert IDE reset */ -.endm - -#define PLATFORM_SETUP m5249c3_setup - -#endif /* __ASSEMBLER__ */ - -/****************************************************************************/ -#endif /* m5249sim_h */ |