| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for the other three palette formats possible with
the PXA LCD controller. This is required on boards where an LCD is connected
with all its 18 bits. With this patch, it's possible to use an 8-bit mode
with 18-bit palette entries. This used to be possible in 2.4 kernels but
disappeared in 2.6. With current kernels, you can only get wrong colours
out of an LCD connected this way.
Users can choose the palette format by doing something like this
in their board definition:
static struct pxafb_mach_info my_fb_info = {
[...]
.lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_PDFOR_3,
.lccr4 = LCCR4_PAL_FOR_2,
[...]
};
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This contains the following changes:
* Overlay surface alpha is configured separately from the overlay. This
prevents display glitches (configure and fill the overlay first, set
alpha to a visible value next)
* Added an ioctl for configuring transparency of the Overlay and graphics
planes. Blend mode, colorkey mode and global alpha mode are supported.
* Added an ioctl for setting the plane order. The overlay plance can be placed
over or
under the graphics plane.
* Added an ioctl for setting and reading chip registers, with mask.
* Updated copyright for 2007
[adaplas]
* Coding style changes
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we setup the panel interface whilst configuring the
framebuffer, we should ensure the panel interface is not
in tristate, in case the bootloader or previous setup has
not enabled it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Call the fb_set_suspend() over suspend and resume.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The suspend and resume code is failing to restore the CRT control
register, thus causing the CRT data-path to get changed if the
SM501 experiences a reset over suspend.
Also move some of the debug messages to dev_dbg() level and ensure
that the suspend code does not try and restore anything it did not
manage to save.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds accelerated fillrect for 24-bit depth.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch:
- initializes correctly the Permedia2V chip if it is not initialized by BIOS
- puts back clock frequency for the ELSA WINNER board to 100kHz
- fixes returned error values from setcolreg() function
- uses more general classes for PCI ids
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch concentrates on source compacting, simplification and more
conformance to kernel coding standards.
The major changes:
- RD32() and WR() functions are merged into pm2_RD() and pm2_WR()
- conditional (with switch()) RDAC functions are separated in two
unconditional ones
- the conditional pm2fb_block_op() function is merged into pm2fb_fillrect()
and pm2fb_copyarea()
- WAIT_FIFO() values are corrected
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds accelerated imageblit function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds usage of MTRR registers and two new options: noaccel and
nomtrr.
[bunk@kernel.org: make pm3fb_init() static again]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch contains improvements:
- it adds ROP_XOR in pm3fb_fillrect()
- it conforms closer to coding style
- it removes redundant parentheses and setting bits with 0 value
- it checks if hardware acceleration is disabled in pm3fb_imageblit
- it adds module description
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch contains 3 small improvements:
- it corrects scan line width calculation in pm3fb_imageblit()
- it corrects mmio mapping for big endian machines
- it enables panning acceleration constants
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes the pm3_imageblit() restriction to blit only images with
width divisable by 32.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes constants named AAA_DISABLE with value 0. They are redudant
and misleading ( a |= AAA_DISABLE does nothing and usually should be
a &= ~AAA_ENABLE).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch corrects name of the field.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds accelerated copyarea and partially accelerated imageblit
functions. There is also fixed one register address in the pm3fb.h file.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Documentation for the uvesafb driver.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
uvesafb is an enhanced version of vesafb. It uses a userspace helper (v86d)
to execute calls to the x86 Video BIOS functions. The driver is not limited
to any specific arch and whether it works on a given arch or not depends on
that arch being supported by the userspace daemon. It has been tested on
x86_32 and x86_64.
A single BIOS call is represented by an instance of the uvesafb_ktask
structure. This structure contains a buffer, a completion struct and a
uvesafb_task substructure, containing the values of the x86 registers, a flags
field and a field indicating the length of the buffer. Whenever a BIOS call
is made in the driver, uvesafb_exec() builds a message using the uvesafb_task
substructure and the contents of the buffer. This message is then assigned a
random ack number and sent to the userspace daemon using the connector
interface.
The message's sequence number is used as an index for the uvfb_tasks array,
which provides a mapping from the messages coming from userspace to the
in-kernel uvesafb_ktask structs.
The userspace daemon performs the requested operation and sends a reply in the
form of a uvesafb_task struct and, optionally, a buffer. The seq and ack
numbers in the reply should be exactly the same as those in the request.
Each message from userspace is processed by uvesafb_cn_callback() and after
passing a few sanity checks leads to the completion of a BIOS call request.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add connector idx and val constants for v86d and uvesafb.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change the maximum message size to 16k to allow transfers of VBE
data blocks from userspace.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make fb_destroy_modelist an exported symbol for use in the uvesafb driver.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/char/rtc.c allowed RTC_PIE_ON ioctls for non-root users, as long as
the current interval (set via RTC_IRQP_SET) is <= max_user_freq. Allow
RTC_PIE_ON under the same conditions when /dev/rtc* is handled by the rtc
subsystem.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/char/rtc.c exposed a sysctl to change the maximum frequency at
which a non-root user could ask the RTC to generate interrupts (via the
RTC_IRQP_SET ioctl). This value is no longer available under the new RTC
subsystem, so add it to sysfs for each RTC device.
Works for me on x86_64 (both reads and writes), using rtc-cmos.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some cleanups for the rtc-cmos probe logic:
- Claim i/o ports with request_region() not request_resource(),
for better coexistence betwen platform and pnp bus glues.
- Claim those ports earlier, to help work around procfs bugs
(it allows duplicate names, like /proc/driver/rtc).
- Fix some glitches in cleanup code, notably a cut'n'paste-o
where the i/o port region might not get released during
cleanup after a probe fault.
And some comment clarifications, including noting that this code
must work with PNPBIOS not just PNPACPI..
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix readback of RTC alarms on platforms which return -1 in
non-hardware-supported RTC alarm fields.
To fill in the missing (-1) values, we grab an RTC timestamp along with the
RTC alarm value, and use the timestamp fields to populate the missing alarm
fields.
To counter field-wrap races (since the timestamp and alarm are not read
together atomically), we read the RTC timestamp both before and after
reading the RTC alarm value, and then check for wrapped fields --> if any
have wrapped, we know we have a possible inconsistency, so we loop and
reread the timestamp and alarm again.
Wrapped fields in the RTC timestamps are an issue because rtc-cmos.c, for
example, also gets/uses an RTC timestamp internally while fetching the RTC
alarm. If our timestamp here wasn't the same (minutes and higher) as what
was used internally there, then we might end up populating the -1 fields
with inconsistent values.
This fixes readbacks from /sys/class/rtc/rtc?/wakealarm, as well as other
code paths which call rtc_read_alarm().
Signed-off-by: Mark Lord <mlord@pobox.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds an RTC class driver for the Maxim/Dallas 1374 RTC chip,
based on drivers/i2c/chips/ds1374.c. It supports alarm functionality.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Not all i2c adapters support I2C-level messaging. Check that the adapter
does before probing for a PCF8583 chip, as the driver makes use of
i2c_transfer and i2c_master_send.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtc-ds1742 platform driver name doesn't match its module name,
which might prevents it from properly hotplugging. There is only two
in-tree user of its driver, which are fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtc-ds1553 platform driver name doesn't match its module name, which
might prevent it from properly hotplugging. This driver has no in-tree
users.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In rtc-dev.c, when a rtc device is opened, file->private_data is already
attached with the rtc device pointer, so there is no need to call
to_rtc_device() to convert file->private_data to a rtc device pointer.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Mark Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC periodic IRQs are only defined to work for 2^N Hz values. This patch
moves that validity check into the infrastructure, so drivers don't need to
check it; and adds kerneldoc for the two interface functions related to
periodic IRQs. (One of which was quite mysterious until its first use was
recently checked in!)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add kernel/kernel and kernel/user locking for the periodic irq feature of
the rtc class.
PIE ioctls are also supported.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The functions that eventually call down to ecryptfs_read_lower(),
ecryptfs_decrypt_page(), and ecryptfs_copy_up_encrypted_with_header()
should have the responsibility of managing the page Uptodate
status. This patch gets rid of some of the ugliness that resulted from
trying to push some of the page flag setting too far down the stack.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace some magic numbers with sizeof() equivalents.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The switch to read_write.c routines and the persistent file make a number of
functions unnecessary. This patch removes them.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Initialize persistent lower file on inode create.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update data types and add casts in order to avoid potential overflow
issues.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert readpage, prepare_write, and commit_write to use read_write.c
routines. Remove sync_page; I cannot think of a good reason for implementing
that in eCryptfs.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rather than open a new lower file for every eCryptfs file that is opened,
truncated, or setattr'd, instead use the existing lower persistent file for
the eCryptfs inode. Change truncate to use read_write.c functions. Change
ecryptfs_getxattr() to use the common ecryptfs_getxattr_lower() function.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the metadata read/write functions and grow_file() to use the
read_write.c routines. Do not open another lower file; use the persistent
lower file instead. Provide a separate function for
crypto.c::ecryptfs_read_xattr_region() to get to the lower xattr without
having to go through the eCryptfs getxattr.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch sets up and destroys the persistent lower file for each eCryptfs
inode.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace page encryption and decryption routines and inode size write routine
with versions that utilize the read_write.c functions.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a set of functions through which all I/O to lower files is consolidated.
This patch adds a new inode_info reference to a persistent lower file for each
eCryptfs inode; another patch later in this series will set that up. This
persistent lower file is what the read_write.c functions use to call
vfs_read() and vfs_write() on the lower filesystem, so even when reads and
writes come in through aops->readpage and aops->writepage, we can satisfy them
without resorting to direct access to the lower inode's address space.
Several function declarations are going to be changing with this patchset.
For now, in order to keep from breaking the build, I am putting dummy
parameters in for those functions.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The error paths and the module exit code need work. sysfs
unregistration is not the right place to tear down the crypto
subsystem, and the code to undo subsystem initializations on various
error paths is unnecessarily duplicated. This patch addresses those
issues.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove assignments in if-statements.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is no point to keeping a separate header_extent_size and an extent_size.
The total size of the header can always be represented as some multiple of
the regular data extent size.
[randy.dunlap@oracle.com: ecryptfs: fix printk format warning]
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
eCryptfs is currently just passing through splice reads to the lower
filesystem. This is obviously incorrect behavior; the decrypted data is
what needs to be read, not the lower encrypted data. I cannot think of any
good reason for eCryptfs to implement splice_read, so this patch points the
eCryptfs fops splice_read to use generic_file_splice_read.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Reviewed-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Andrew Morton wrote:
> Please check that all the newly-added global symbols do indeed need
> to be global.
Change symbols in keystore.c and crypto.o to static if they do not
need to be global.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Andrew Morton wrote:
> > struct mutex *tfm_mutex = NULL;
>
> This initialisation looks like it's here to kill bogus gcc warning
> (if it is, it should have been commented). Please investigate
> uninitialized_var() and __maybe_unused sometime.
Remove some unnecessary variable initializations. There may be a few
more such intializations remaining in the code base; a future patch
will take care of those.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Andrew Morton wrote:
From: mhalcrow@us.ibm.com <mhalcrow@halcrow.austin.ibm.com>
> > +/**
> > + * decrypt_passphrase_encrypted_session_key - Decrypt the session key
> > + * with the given auth_tok.
> > *
> > * Returns Zero on success; non-zero error otherwise.
> > */
>
> That comment purports to be a kerneldoc-style comment. But
>
> - kerneldoc doesn't support multiple lines on the introductory line
> which identifies the name of the function (alas). So you'll need to
> overflow 80 cols here.
>
> - the function args weren't documented
>
> But the return value is! People regularly forget to do that. And
> they frequently forget to document the locking prerequisites and the
> permissible calling contexts (process/might_sleep/hardirq, etc)
>
> (please check all ecryptfs kerneldoc for this stuff sometime)
This patch cleans up some of the existing comments and makes a couple
of line break tweaks. There is more work to do to bring eCryptfs into
full kerneldoc-compliance.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
