| Age | Commit message (Collapse) | Author |
|---|
|
According to the comments, we rely on the OTG timer because the core
does not expose some important OTG details. So far this is all I
know. After playing with OTG I stumbled over a problem:
musb is recognized as a B-device without a problem. Whenever a cable is
plugged, the VBUS rises, musb recognizes this as a starting session,
sets the MUSB_DEVCTL_SESSION bit by itself and a RESET interrupt occurs,
the session starts. Good.
After a disconnect, the timer is started and re-starts itself because
it remains in B_IDLE with the BDEVICE set. I didn't figure the the
reason or the need for it. Nothing changes here except for OTG state
from B to A device if the BDEVICE bit disappears. This doesn't make much
sense to me because nothing happens after this. _IF_ we receive an
interrupt before the state change then we may act on wrong condition.
Plugging a B-device (and letting MUSB act as host) doesn't work here.
The reason seems to be that the MUSB tries to start a session, it fails
and then it removes the bit. So we never start as a host.
This patch sets the MUSB_DEVCTL_SESSION bit in the IDLE state so musb
can try to establish a session as host. After the bit is set, musb tries
to start a session and if it fails it clears the bit. Therefore it will
try over and over again until a session either as host or as device is
established.
The readout of the MUSB_DEVCTL register after the removal the
MUSB_DEVCTL_SESSION (in A_WAIT_BCON) has been removed because it did not
contain the BDEVICE bit set (in the second read) leading to A_IDLE. After
plugging a host musb assumed that it is also a host and complained about
a missing reset. However a third read of the register has has the BDEVICE
bit set so it seems that it is not stable.
This mostly what da8xx.c is doing except that we set the timer also
after A_WAIT_BCON so the session bit can be triggered.
Whit this change I was able to keep am335x-evm in OTG mode and plug in
either a HOST or a DEVICE and in a random order and the device was
recognized.
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch moves dsps_musb_try_idle() before dsps_musb_enable() so the
declaration (of dsps_musb_try_idle() can be removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The timer is initialized right after musb is probed. There is actually
no need to have this timer running because _nothing_ will happen until
we have the gadget loaded. Also we need this timer only if we run in OTG
mode _and_ we need it also after the gadget has been replaced with
another one.
I've been looking at am35x.c, da8xx.c, omap2430.c, tusb6010.c. da8xx
seem to have the same problem as dsps and doing mostly the same thing.
tusb6010 seem to do something different and do some actual "idle / power
saving" work so I am not too comfortable to remove
musb_platform_try_idle() from musb_gadget_setup().
Therefore this patch does not start the timer if there is no gadget
active (which is at musb_gadget_setup() at time). In order to have the
timer active after the gadget is loaded it will be triggered from
dsps_musb_enable().
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In commit 001dd84 ("usb: musb: start musb on the udc side, too") it was
ensured that the state engine is started also in OTG mode after a
removal / insertion of the gadget.
Unfortunately this change also introduced a bug: If the device is
configured as OTG and it connected with a remote host _without_ loading
a gadget then we bug() later (because musb->otg->gadget is not
initialized).
Initially I assumed it might be nice to have the host part of musb in
OTG mode working without having a gadget loaded. This bug and fact that
it wasn't working like this before the host/gadget split made me realize
that this was a silly idea.
This patch now introduces back the old behavior where in OTG mode the
host mode is only working after the gadget has been loaded.
Cc: stable@vger.kernel.org # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Value of can_write variable in s3c_hsotg_write_fifo function should be limited
to 512 only for non-periodic endpoints. There was some discrepancy between
comment and code, becouse comment suggests correct behavior, but in the code
limit was applied to periodic endpoints too. So there is additional check
causing the limitation concerns only non-periodic endpoints.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In dedicated-fifo mode TxFIFOEmpty interrupt should be asserted when TxFIFO
for this endpoint is completly empty, so NPTxFEmpLvl and PTxFEmpLvl bits are
set in GAHBCFG register.
In DIEPMSK register INTknTXFEmpMsk is set, becouse it's needed to indicate
FIFO Empty state.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
All requests for endpoint are completed when it was halted and the halt was
cleared by CLEAR_FEATURE, but not when new state is same as previous.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Property "halted" of s3c_hsotg_ep structure is actually initialised when ep
enabled, and changed when halt is set/cleared.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In OEPInt/IEPInt interrupts handling added bitwise and of DAINT and
DAINTMSK, because we should handle masked interrupts only.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When s3c_hsotg_trytx is called for ep without enqueued request, interrupts
for this ep are disabled, to prevent interrupt flooding. Interrupts are
enabled when new request for this ep is starting.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
mode
In s3c_hsotg_write_fifo function PTxFEmp/NPTxFEmp interrupts are enabled
only in shared-fifo mode. In dedicated-fifo mode they should not be used
(when enabled then cause interrupt storm).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After normal handling of SetupDone interrupt, XferCompl interrupt occurs, and
then we enqueue new setup request. But when ep0 is stalled, there is no
XferCompl, so we have to enqueue setup request immediately after stalling ep.
Otherwise incoming control requests won't be processed correctly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If cdrom flag is set ro flag is implied. Try setting the ro first, and
only if it succeeds set the cdrom flag.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
strtobool is more flexible for the user and is more appropriate in the
context.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The callers are expecting an ERR_PTR value in case
of an error. Change he code to return with an encoded
-ENOMEM value in the case of a failed devres_alloc call.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Create a way for VERBOSE_DEBUG to be enabled during
drivers/usb/gadget/ build.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes unused label.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds Multi Count support. It adds few modifications:
- Fix s3c_hsotg_set_ep_maxpacket() function. Field wMaxPacketSize of endpoint
descriptor is now splitted into maximum packet size value and number of
additional transaction per microframe.
- Modify s3c_hsotg_write_fifo() function. It actually calculates transfer
size, taking into account Multi Count value, which indicates number of
transactions per microframe.
- Fix s3c_hsotg_start_req() function by setting number of packets to Multi
Count field in DIEPTSIZ register for isochronous endpoints.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds isochronous transfer support. It adds few modifications:
- Modify s3c_hsotg_epint() function. Some interrupts are ignored for
isochronous endpoints, (e.g. INTknTXFEmpMsk) becouse isochronous request is
always transfered in single transaction, which ends with XferCompl interrupt.
- Add Odd/Even microframe toggle to allow data transfering in each microframe
in s3c_hsotg_epint() function.
- Fix s3c_hsotg_ep_enable() function by supporting isochronous endpoint type.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We are going to disable runtime_pm and we're
removing the driver, we must disable the device
now.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This adds RCAR Gen2 USB phy support. The driver configures
USB channels 0/2 which are shared between PCI USB hosts and
USBHS/USBSS devices. It also controls internal USBHS phy.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
So I captured this:
|WARNING: CPU: 0 PID: 2078 at /home/bigeasy/work/new/TI/linux/lib/debugobjects.c:260 debug_print_object+0x94/0xc4()
|ODEBUG: free active (active state 0) object type: work_struct hint: musb_irq_work+0x0/0x38 [musb_hdrc]
|CPU: 0 PID: 2078 Comm: rmmod Not tainted 3.12.0-rc4+ #338
|[<c0014d38>] (unwind_backtrace+0x0/0xf4) from [<c001249c>] (show_stack+0x14/0x1c)
|[<c001249c>] (show_stack+0x14/0x1c) from [<c0037720>] (warn_slowpath_common+0x64/0x84)
|[<c0037720>] (warn_slowpath_common+0x64/0x84) from [<c00377d4>] (warn_slowpath_fmt+0x30/0x40)
|[<c00377d4>] (warn_slowpath_fmt+0x30/0x40) from [<c022ae90>] (debug_print_object+0x94/0xc4)
|[<c022ae90>] (debug_print_object+0x94/0xc4) from [<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228)
|[<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228) from [<c00f1f38>] (kfree+0xf8/0x228)
|[<c00f1f38>] (kfree+0xf8/0x228) from [<c02921c4>] (release_nodes+0x1a8/0x248)
|[<c02921c4>] (release_nodes+0x1a8/0x248) from [<c028f70c>] (__device_release_driver+0x98/0xf0)
|[<c028f70c>] (__device_release_driver+0x98/0xf0) from [<c028f840>] (device_release_driver+0x24/0x34)
|[<c028f840>] (device_release_driver+0x24/0x34) from [<c028ebe8>] (bus_remove_device+0x148/0x15c)
|[<c028ebe8>] (bus_remove_device+0x148/0x15c) from [<c028d120>] (device_del+0x104/0x1c0)
|[<c028d120>] (device_del+0x104/0x1c0) from [<c02911e4>] (platform_device_del+0x18/0xac)
|[<c02911e4>] (platform_device_del+0x18/0xac) from [<c029179c>] (platform_device_unregister+0xc/0x18)
|[<c029179c>] (platform_device_unregister+0xc/0x18) from [<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps])
|[<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps]) from [<c0290d7c>] (platform_drv_remove+0x1c/0x24)
|[<c0290d7c>] (platform_drv_remove+0x1c/0x24) from [<c028f704>] (__device_release_driver+0x90/0xf0)
|[<c028f704>] (__device_release_driver+0x90/0xf0) from [<c028f818>] (driver_detach+0xb4/0xb8)
|[<c028f818>] (driver_detach+0xb4/0xb8) from [<c028e6e8>] (bus_remove_driver+0x98/0xec)
|[<c028e6e8>] (bus_remove_driver+0x98/0xec) from [<c008fc70>] (SyS_delete_module+0x1e0/0x24c)
|[<c008fc70>] (SyS_delete_module+0x1e0/0x24c) from [<c000e680>] (ret_fast_syscall+0x0/0x48)
|---[ end trace d79045419a3e51ec ]---
The workqueue is only scheduled from the ep0 and never canceled in case
the musb is removed before the work has a chance to run.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
u_ms.ko is needed only together with usb_f_mass_storage.ko. Merge them.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There are no more old interface users left. Remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert the legacy multi gadget to the new interface of f_mass_storage,
so that later the compatibility layer in f_mass_storage can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert the legacy multi gadget to the new interface of f_rndis,
so that later the compatibility layer in f_rndis can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert the legacy multi gadget to the new interface of f_ecm,
so that later the compatibility layer in f_ecm can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert the legacy acm_ms gadget to use the new function interface
of f_mass_storage, so that later the compatibility layer in
f_mass_storage can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
From this commit on f_mass_storage is available through configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This will be required by configfs integration.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Show/store methods for sysfs attributes contain code which can be used
also by configfs. Make them abstract the source the lun and rw_semaphore
are taken from.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert old mass_storage gadget to use the new interface of f_mass_storage
so that later the compatibility layer in f_mass_storage can be removed.
struct fsg_common is not known to mass_storage.c, so a setter method
is added to f_mass_storage.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
compatibility
Converting mass storage to the new function interface requires converting
the USB mass storage's function code and its users.
This patch converts the f_mass_storage.c to the new function interface.
The file is now compiled into a separate usb_f_mass_storage.ko module.
The old function interface is provided by means of a preprocessor conditional
directives. After all users are converted, the old interface can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init
fsg_common_init is a lengthy function. Factor portions of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init
fsg_common_init is a lengthy function. Factor portions of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When configfs is in place, the luns will not be represented in sysfs,
so there will be no struct device associated with a lun.
In order to maintain compatibility and allow configfs adoption
sysfs is made optional in this patch.
As a consequence some debug macros need to be adjusted. Two new
fields are added to struct fsg_lun: name and name_pfx.
The "name" is for storing a string which is presented to the user
instead of the dev_name. The "name_pfx", if non-NULL, is prepended
to the "name" at printing time.
The name_pfx is for a future lun.0, which will be a default group in
mass_storage.<name>. By design at USB function configfs group's creation
time its name is not known (but instead set a bit later in
drivers/usb/gadget/configfs.c:function_make) and it is this name that
serves the purpose of the said name prefix. So instead of copying
a yet-unknown string a pointer to it is stored in struct fsg_lun.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When configfs is in place, gadgets will have to be able to free
fsg buffers. Add a helper function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixes max packet size check in s3c_hsotg_set_ep_maxpacket()
function. According USB specification, bits 10..0 of mps specifies maximum
packet size, so there is bitwise AND between mps and 0x7ff value. Also added
check if maxpacket isn't grater than 1024 which is maximum size od single USB
transaction.
In s3c_hsotg_ep_enable() function added s3c_hsotg_set_ep_maxpacket() call
instead of setting ep.maxpacket value directly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If USB_FUNCTIONFS is selected without USB_FUNCTIONFS_ETH and
USB_FUNCTIONFS_RNIS, u_ether.h won't be included and then
USB_ETHERNET_MODULE_PARAMAETERS macro won't be available causing the
following warning compilation:
drivers/usb/gadget/g_ffs.c:81:1: warning: data definition has no type or
storage class [enabled by default]
drivers/usb/gadget/g_ffs.c:81:1: warning: type defaults to ‘int’ in
declaration of ‘USB_ETHERNET_MODULE_PARAMETERS’ [-Wimplicit-int]
drivers/usb/gadget/g_ffs.c:81:1: warning: function declaration isn’t a
prototype [-Wstrict-prototypes]
This patch fixes the warning by making USB_ETHERNET_MODULE_PARAMETERS to
be used iff u_ether.h is included, otherwise it is not needed.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch changes ep maxpacket value from 512 to 1024, because it's needed
to handle interupt and isochronous endpoints in high-speed mode. This change
doesn't affect on driver functioning, because fifo size (3072) is still enough
for the maximum transaction payload (3*1024 for high-speed high-bandwidtch
endpoints).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Reorder variables in struct otg_fsm as they appear in OTG and EH
supplement to USB2.0.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Several input/output variables missed in current FSM implementation.
This patch adds and makes use of them as specified in OTG and EH
supplement to USB2.0.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In accordance with OTG and EH supplement, the correct name
of the FSM input is b_ssend_srp.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Mark informative variables with suffix '_inf' to distinguish
them from other non-informative variables with the same name.
If such non-informative varialbes were missed, they are created.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
