Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes on 20120224:
"This is a set of assorted bug fixes for power management, mpt2sas,
ipr, the rdac device handler and quite a big chunk for qla2xxx (plus a
use after free of scsi_host in scsi_scan.c). "
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_dh_rdac: Fix for unbalanced reference count
[SCSI] scsi_pm: Fix bug in the SCSI power management handler
[SCSI] scsi_scan: Fix 'Poison overwritten' warning caused by using freed 'shost'
[SCSI] qla2xxx: Update version number to 8.03.07.13-k.
[SCSI] qla2xxx: Proper detection of firmware abort error code for ISP82xx.
[SCSI] qla2xxx: Remove resetting memory during device initialization for ISP82xx.
[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.
[SCSI] qla2xxx: Remove check for null fcport from host reset handler.
[SCSI] qla2xxx: Correct out of bounds read of ISP2200 mailbox registers.
[SCSI] qla2xxx: Remove errant clearing of MBX_INTERRUPT flag during CT-IOCB processing.
[SCSI] qla2xxx: Clear options-flags while issuing stop-firmware mbx command.
[SCSI] qla2xxx: Add an "is reset active" helper.
[SCSI] qla2xxx: Add check for null fcport references in qla2xxx_queuecommand.
[SCSI] qla2xxx: Propagate up abort failures.
[SCSI] isci: Fix NULL ptr dereference when no firmware is being loaded
[SCSI] ipr: fix eeh recovery for 64-bit adapters
[SCSI] mpt2sas: Fix mismatch in mpt2sas_base_hard_reset_handler() mutex lock-unlock
|
|
This patch fixes a (mostly cosmetic) bug introduced by the patch
'ppp: Use SKB queue abstraction interfaces in fragment processing'
found here: http://www.spinics.net/lists/netdev/msg153312.html
The above patch rewrote and moved the code responsible for cleaning
up discarded fragments but the new code does not catch every case
where this is necessary. This results in some discarded fragments
remaining in the queue, and triggering a 'bad seq' error on the
subsequent call to ppp_mp_reconstruct. Fragments are discarded
whenever other fragments of the same frame have been lost.
This can generate a lot of unwanted and misleading log messages.
This patch also adds additional detail to the debug logging to
make it clearer which fragments were lost and which other fragments
were discarded as a result of losses. (Run pppd with 'kdebug 1'
option to enable debug logging.)
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sparse complaints the endian bug.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts a portion of d0bc1fb4 so that coccicheck will
work properly when C=1 or C=2.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
|
|
The original spelling and bad word choice makes these comments hard to read.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware generates an interrupt for every completed command in the
queue while the code assumed that it will only generate one interrupt
when the queue is empty. So, explicitly check if the queue is really
empty. This patch fixed problems which occurred due to high traffic on
the bus. While we are here, move the completion-initialization after the
parameter error checking.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
|
|
signalfd_cleanup() ensures that ->signalfd_wqh is not used, but
this is not enough. eppoll_entry->whead still points to the memory
we are going to free, ep_unregister_pollwait()->remove_wait_queue()
is obviously unsafe.
Change ep_poll_callback(POLLFREE) to set eppoll_entry->whead = NULL,
change ep_unregister_pollwait() to check pwq->whead != NULL under
rcu_read_lock() before remove_wait_queue(). We add the new helper,
ep_remove_wait_queue(), for this.
This works because sighand_cachep is SLAB_DESTROY_BY_RCU and because
->signalfd_wqh is initialized in sighand_ctor(), not in copy_sighand.
ep_unregister_pollwait()->remove_wait_queue() can play with already
freed and potentially reused ->sighand, but this is fine. This memory
must have the valid ->signalfd_wqh until rcu_read_unlock().
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Cc: <stable@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Cc: <stable@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before loading the lut (gamma), check the active state of intel_crtc,
otherwise at least on gen2 hang ensue.
This is reproducible in Xorg via:
xset dpms force off
then
xgamma -rgamma 2.0 # freeze.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44505
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
As noticed by Torsten Kaiser, the operator precedence can play tricks with
us here.
CC: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Quoth Chris:
"This is later than I wanted because I got backed up running through
btrfs bugs from the Oracle QA teams. But they are all bug fixes that
we've queued and tested since rc1.
Nothing in particular stands out, this just reflects bug fixing and QA
done in parallel by all the btrfs developers. The most user visible
of these is:
Btrfs: clear the extent uptodate bits during parent transid failures
Because that helps deal with out of date drives (say an iscsi disk
that has gone away and come back). The old code wasn't always
properly retrying the other mirror for this type of failure."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (24 commits)
Btrfs: fix compiler warnings on 32 bit systems
Btrfs: increase the global block reserve estimates
Btrfs: clear the extent uptodate bits during parent transid failures
Btrfs: add extra sanity checks on the path names in btrfs_mksubvol
Btrfs: make sure we update latest_bdev
Btrfs: improve error handling for btrfs_insert_dir_item callers
Btrfs: be less strict on finding next node in clear_extent_bit
Btrfs: fix a bug on overcommit stuff
Btrfs: kick out redundant stuff in convert_extent_bit
Btrfs: skip states when they does not contain bits to clear
Btrfs: check return value of lookup_extent_mapping() correctly
Btrfs: fix deadlock on page lock when doing auto-defragment
Btrfs: fix return value check of extent_io_ops
btrfs: honor umask when creating subvol root
btrfs: silence warning in raid array setup
btrfs: fix structs where bitfields and spinlock/atomic share 8B word
btrfs: delalloc for page dirtied out-of-band in fixup worker
Btrfs: fix memory leak in load_free_space_cache()
btrfs: don't check DUP chunks twice
Btrfs: fix trim 0 bytes after a device delete
...
|
|
This is the arch/c6x part of commit 7c43185138cf ("Kbuild: Use dtc's -d
(dependency) option") which was dropped because c6x had not yet been
merged at the time.
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
Kbuild: Use dtc's -d (dependency) option
|
|
This fixes a kernel oops with CONFIG_DEBUG_VM triggered by a
VM_BUG_ON(bad_range()): kernel BUG at mm/page_alloc.c:748.
With memory hotplug on System z, it is possible that the memory
online/offline state is preserved over a system restart, e.g. there
may be offline memory blocks in ZONE_DMA or ZONE_NORMAL. So far,
the offline memory range has always been added to ZONE_MOVABLE during
system start, so that it was possible to have ZONE_MOVABLE interleave
with ZONE_DMA or ZONE_NORMAL. This patch fixes that by checking for
zone overlap before adding memory.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
arch/s390/kernel/crash_dump.c included 'linux/crash_dump.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Enable the compat keyctl wrapper on s390x so that 32-bit s390 userspace can
call the keyctl() syscall.
There's an s390x assembly wrapper that truncates all the register values to
32-bits and this then calls compat_sys_keyctl() - but the latter only exists if
CONFIG_KEYS_COMPAT is enabled, and the s390 Kconfig doesn't enable it.
Without this patch, 32-bit calls to the keyctl() syscall are given an ENOSYS
error:
[root@devel4 ~]# keyctl show
Session Keyring
-3: key inaccessible (Function not implemented)
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: dan@danny.cz
Cc: Carsten Otte <cotte@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
I don't even live in the same country as any of my PA-RISC hardware
these days, so the odds of me touching the code are pretty low.
(Also re-order things to ensure jejb gets CC'd since he's been the
primary maintainer for the last few years.)
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't clear vm_mm in a deleted VMA as it's unnecessary and might
conceivably break the filesystem or driver VMA close routine.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Lock i_mmap_mutex for access to the VMA prio list to prevent concurrent
access. Currently, certain parts of the mmap handling are protected by
the region mutex, but not all.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SH/R-Mobile fixes for 3.3-rc5
* tag 'rmobile-for-linus' of git://github.com/pmundt/linux-sh:
arch/arm/mach-shmobile/board-ag5evm.c: included linux/dma-mapping.h twice
ARM: mach-shmobile: r8a7779 PFC IPSR4 fix
ARM: mach-shmobile: sh73a0 PSTR 32-bit access fix
ARM: mach-shmobile: add GPIO-to-IRQ translation to sh7372
ARM: mach-shmobile: clock-sh73a0: add DSIxPHY clock support
arm: fix compile failure in mach-shmobile/board-ag5evm.c
ARM: mach-shmobile: mackerel: add ak4642 amixer settings on comment
ARM: mach-shmobile: mackerel: use renesas_usbhs instead of r8a66597_hcd
ARM: mach-shmobile: simplify MMCIF DMA configuration
ARM: mach-shmobile: IRQ driven GPIO key support for Kota2
ARM: mach-shmobile: sh73a0 IRQ sparse alloc fix
ARM: mach-shmobile: sh73a0 PINT IRQ base fix
|
|
SuperH fixes for 3.3-rc5
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix sh2a build error for CONFIG_CACHE_WRITETHROUGH
sh: modify a resource of sh_eth_giga1_resources in board-sh7757lcr
arch/sh: remove references to cpu_*_map.
sh: Fix typo in pci-sh7780.c
sh: add platform_device for SPI1 in setup-sh7757
sh: modify resource for SPI0 in setup-sh7757
sh: se7724: fix compile breakage
sh: clkfwk: bugfix: use clk_reparent() for div6 clocks
sh: clock-sh7724: fixup sh_fsi clock settings
sh: sh7757lcr: update to the new MMCIF DMA configuration
sh: fix the sh_mmcif_plat_data in board-sh7757lcr
video: pvr2fb: Fix up spurious section mismatch warnings.
sh: Defer to asm-generic/device.h.
|
|
There is an issue when memcg unregisters events that were attached to
the same eventfd:
- On the first call mem_cgroup_usage_unregister_event() removes all
events attached to a given eventfd, and if there were no events left,
thresholds->primary would become NULL;
- Since there were several events registered, cgroups core will call
mem_cgroup_usage_unregister_event() again, but now kernel will oops,
as the function doesn't expect that threshold->primary may be NULL.
That's a good question whether mem_cgroup_usage_unregister_event()
should actually remove all events in one go, but nowadays it can't
do any better as cftype->unregister_event callback doesn't pass
any private event-associated cookie. So, let's fix the issue by
simply checking for threshold->primary.
FWIW, w/o the patch the following oops may be observed:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffff810be32c>] mem_cgroup_usage_unregister_event+0x9c/0x1f0
Pid: 574, comm: kworker/0:2 Not tainted 3.3.0-rc4+ #9 Bochs Bochs
RIP: 0010:[<ffffffff810be32c>] [<ffffffff810be32c>] mem_cgroup_usage_unregister_event+0x9c/0x1f0
RSP: 0018:ffff88001d0b9d60 EFLAGS: 00010246
Process kworker/0:2 (pid: 574, threadinfo ffff88001d0b8000, task ffff88001de91cc0)
Call Trace:
[<ffffffff8107092b>] cgroup_event_remove+0x2b/0x60
[<ffffffff8103db94>] process_one_work+0x174/0x450
[<ffffffff8103e413>] worker_thread+0x123/0x2d0
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Temperature history is reset by writing 0x8000 into the peak temperature
register, not 0xffff.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
The enospc tracing code added some interesting uses of
u64 pointer casts.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
Fix this:
root@omap4430-panda:~# cat /debug/iommu/ducati/mem
[ 62.725708] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000001c
[ 62.725708] pgd = e6240000
[ 62.737091] [0000001c] *pgd=a7168831, *pte=00000000, *ppte=00000000
[ 62.743682] Internal error: Oops: 17 [#1] SMP
[ 62.743682] Modules linked in: omap_iommu_debug omap_iovmm virtio_rpmsg_bus o
map_remoteproc remoteproc virtio_ring virtio mailbox_mach mailbox
[ 62.743682] CPU: 0 Not tainted (3.3.0-rc1-00265-g382f84e-dirty #682)
[ 62.743682] PC is at debug_read_mem+0x5c/0xac [omap_iommu_debug]
[ 62.743682] LR is at 0x1004
[ 62.777832] pc : [<bf033178>] lr : [<00001004>] psr: 60000013
[ 62.777832] sp : e72c7f40 ip : c0763c00 fp : 00000001
[ 62.777832] r10: 00000000 r9 : 00000000 r8 : e72c7f80
[ 62.777832] r7 : e6ffdc08 r6 : bed1ac78 r5 : 00001000 r4 : e7276000
[ 62.777832] r3 : e60f3460 r2 : 00000000 r1 : e60f38c0 r0 : 00000000
[ 62.777832] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 62.816375] Control: 10c53c7d Table: a624004a DAC: 00000015
[ 62.816375] Process cat (pid: 1176, stack limit = 0xe72c62f8)
[ 62.828369] Stack: (0xe72c7f40 to 0xe72c8000)
...
[ 62.884185] [<bf033178>] (debug_read_mem+0x5c/0xac [omap_iommu_debug]) from [<c010e354>] (vfs_read+0xac/0x130)
[ 62.884185] [<c010e354>] (vfs_read+0xac/0x130) from [<c010e4a8>] (sys_read+0x40/0x70)
[ 62.884185] [<c010e4a8>] (sys_read+0x40/0x70) from [<c0014a00>] (ret_fast_syscall+0x0/0x3c)
Fix also its 'echo bla > /debug/iommu/ducati/mem' Oops sibling, too.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Adapt omap-iommu-debug to the latest omap-iommu API changes, which
were introduced by commit fabdbca "iommu/omap: eliminate the public
omap_find_iommu_device() method".
In a nutshell, iommu users are not expected to provide the omap_iommu
handle anymore - instead, iommus are attached using their user's device
handle.
omap-iommu-debug is a hybrid beast though: it invokes both public and
private omap iommu API, so fix it as necessary (otherwise a crash
is imminent).
Note: omap-iommu-debug is a bit disturbing, as it fiddles with internal
omap iommu data and requires exposing API which is otherwise not needed.
It should better be more tightly coupled with omap-iommu, to prevent
further bit rot and avoid exposing redundant API. Naturally that's out
of scope for the -rc cycle, so for now just fix the obvious.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
It required to extend (and thus change) nf_conntrack_hash_insert
so that it makes sure conntrack and ctnetlink do not add the same entry
twice to the conntrack table.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This reverts commit af14cca162ddcdea017b648c21b9b091e4bf1fa4.
This patch contains a race condition between packets and ctnetlink
in the conntrack addition. A new patch to fix this issue follows up.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
|
|
From: Ben Hutchings <ben@decadent.org.uk>
Extended VBLKs (those larger than the preset VBLK size) are divided
into fragments, each with its own VBLK header. Our LDM implementation
generally assumes that each VBLK is contiguous in memory, so these
fragments must be assembled before further processing.
Currently the reassembly seems to be done quite wrongly - no VBLK
header is copied into the contiguous buffer, and the length of the
header is subtracted twice from each fragment. Also the total
length of the reassembled VBLK is calculated incorrectly.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
|
|
From: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
|
|
This patch fixes a regression that was introduced by
commit 0a5f38467765ee15478db90d81e40c269c8dda20
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch reverts commit 0a5f38467765ee15478db90d81e40c269c8dda20
and instead issues warnings only if cpdma_chan_submit returns -ENOMEM.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Hegde, Vinay <vinay.hegde@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arch/arm/mach-shmobile/board-ag5evm.c: included 'linux/dma-mapping.h'
twice, remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix the bit field width information for the IPSR4 register
in the r8a7779 pin function controller (PFC).
Without this fix the Marzen board fails to receive data
over the serial console due to misconfigured pin function
for the RX pin.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the sh73a0 SMP code to use 32-bit PSTR access.
This fixes wakeup from deep sleep for sh73a0 secondary CPUs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
rmobile-fixes-for-linus
|
|
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The latest sh_eth driver needs a resource of TSU in the channel 1,
if the controller has TSU registers. So, this patch adds the resource.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This has been obsolescent for a while; time for the final push.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Correct spelling "erorr" to "error" in
arch/sh/drivers/pci/pci-sh7780.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
|
|
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
|
|
fbdev-for-linus
|
|
With kernel 3.1, Christoph removed i_alloc_sem and replaced it with
calls (namely inode_dio_wait() and inode_dio_done()) which are
EXPORT_SYMBOL_GPL() thus they cannot be used by non-GPL file systems and
further inode_dio_wait() was pushed from notify_change() into the file
system ->setattr() method but no non-GPL file system can make this call.
That means non-GPL file systems cannot exist any more unless they do not
use any VFS functionality related to reading/writing as far as I can
tell or at least as long as they want to implement direct i/o.
Both Linus and Al (and others) have said on LKML that this breakage of
the VFS API should not have happened and that the change was simply
missed as it was not documented in the change logs of the patches that
did those changes.
This patch changes the two function exports in question to be
EXPORT_SYMBOL() thus restoring the VFS API as it used to be - accessible
for all modules.
Christoph, who introduced the two functions and exported them GPL-only
is CC-ed on this patch to give him the opportunity to object to the
symbols being changed in this manner if he did indeed intend them to be
GPL-only and does not want them to become available to all modules.
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
CC: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A fix from Jesper Juhl removes an assignment in an ASSERT when a compare
is intended. Two fixes from Mitsuo Hayasaka address off-by-ones in XFS
quota enforcement.
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: make inode quota check more general
xfs: change available ranges of softlimit and hardlimit in quota check
XFS: xfs_trans_add_item() - don't assign in ASSERT() when compare is intended
|
|
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|