| Age | Commit message (Collapse) | Author |
|---|
|
Currently there are two places that trigger a beacon update on PCI
devices. The bss_info_changed callback and the periodic update
triggered by the TBTT or PRETBTT interrupt.
Since the next TBTT or PRETBTT interrupt will periodically fetch an
updated beacon remove the update_beacon call in the bss_info_changed
callback for PCI devices.
In the worst case it will take one beacon interval longer to fetch
the new beacon then before. For devices that have a PRETBTT interrupt
there should be no change at all.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Introduce a beacon_update_locked function that does not acquire the
according beacon mutex to allow beacon updates from atomic context. The
caller has to take care of synchronization.
No functional changes. Just preparation for beacon updates from tasklet
context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch allows to dynamically remove beaconing interfaces without
shutting beaconing down on all interfaces.
The only place to start and stop beaconing are now the start- and
stop_queue callbacks. Hence, we can remove some register writes during
interface bring up (config_intf) and only write the correct sync mode
to the register there.
When multiple beaconing interfaces are present we should enable
beaconing as soon as mac80211 enables beaconing on at least one of
them. The beacon queue gets stopped when the last beaconing
interface was stopped by mac80211. Therefore, introduce another
interface counter to keep track ot the number of enabled beaconing
interfaces and start or stop the beacon queue accordingly.
To allow single interfaces to stop beaconing, add a new driver
callback clear_beacon to clear a single interface's beacon without
affecting the other interfaces. Don't overload the clear_entry callback
for clearing beacons as that would introduce additional overhead
(check for each TX queue) into the clear_entry callback which is used
on the drivers TX/RX hotpaths.
Furthermore, the write beacon callback doesn't need to enable beaconing
anymore but since beaconing should be disabled while a new beacon is
written or cleared we still disable beacon generation and enable it
afterwards again in the driver specific callbacks. However, beacon
related interrupts should not be disabled/enabled here, that's solely
done from the start- and stop queue callbacks. It would be nice to stop
the beacon queue just before the beacon update and enable it afterwards
in rt2x00queue itself instead of the current implementation that relies
on the driver doing the right thing. However, since start- and
stop_queue are mutex protected we cannot use them for atomic beacon
updates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Only use IWL_RATE_COUNT_3945 in 3945 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/ath/ath9k/init.c
|
|
"ath9k: fix tx queue index confusion in debugfs code" changed the debug
function but not the stub.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We use priv->cfg->bt_params && priv->cfg->bt_params->bt_statistics
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We use priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Similar change as we already do for agn, need to avoid
"Error setting Tx power (-5)" message when loading module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mac80211 can request for tx power and channel change in one ->config
call. If that happens, *_send_tx_power functions will try to setup tx
power for old channel, what can be not correct because we already change
the band. I.e error "Failed to get channel info for channel 140 [0]",
can be printed frequently when operating in software scanning mode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
genlmsg_cancel subtracts some constants from its second argument before
calling nlmsg_cancel. nlmsg_cancel then calls nlmsg_trim on the same
arguments. nlmsg_trim tests for NULL before doing any computation, but a
NULL second argument to genlmsg_cancel is no longer NULL due to the initial
subtraction. Nothing else happens in this execution, so the call to
genlmsg_cancel is simply unnecessary in this case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression data;
@@
if (data == NULL) { ...
* genlmsg_cancel(..., data);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The register definition for retry configuration on AR5212 was wrong, and simply
copied over from AR5210. Update the register definitions from the documentation.
Let the short and long retries be configured from mac80211 and use the standard
values of 7 and 4 by default. Also we need to make sure we don't export more
retries than we are configured for to mac80211 (and the rate module) in
hw->max_rate_tries.
Also clean up the code by removing unused defines and variables and drop the
different values for "station retries" - if these need to be different it can
be handled tru ah_retry_long/short.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds the MCS information we currently get
from the drivers into radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Change from the systems team to update PMU setting for AR9485
version of chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Spin_lock has been tried to be acquired twice from ath9k_tasklet
to ath_reset which resulted in a machine freeze.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Updates from the analog team for AR9485 chipsets to set
DDR_PLL2 and DDR_PLL3. Also program the BB_PLL ki
and kd value.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When this PLL hang issue is seen, both Rx and Tx fail to work.
The sqsum_dvc needs to be below 2000 for a good chip. During
this issue the sqsum_dvc value is beyond 80000 and only a
full reset can solve this problem.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The HW has separate filter masks for compressed/uncompressed
BlockAcks and BlockAckRequests. Add them.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c"
changed the behavior of INI overriding which is needed only
for PCI cards. Revert to the original check.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.
Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some vendor specific cipher suites require non-zero key indexes for pairwise
keys, but as of currently, the cfg80211 does not allow it.
As validating they cipher parameters for vendor specific cipher suites is the
job of the driver or hardware/firmware, change the cfg80211 to allow also
non-zero pairwise key indexes for vendor specific ciphers.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now that rx and tx dumps go through the tracing infrastructure,
we no longer need to keep these routines around.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds a few tracepoints to ath5k driver transmit and
receive callbacks in order to record packet traffic.
We record the entire packet in the trace buffer so that
the data can be extracted with trace-cmd and external
plugins.
Compared to the previous debugging calls, this approach
removes an out-of-line function call from the tx and rx
paths in the compiled-in-but-disabled case, while
improving the ability to process the logged data.
A new option, CONFIG_ATH5K_TRACER, is added so that one
may disable the tracepoints completely.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
IEEE80211_WEP_NKID is not used in ath9k any more since the key handling code
has been moved to ath/.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This enables 4.9GHz frequencies in ath5k if they are allowed as indicated by
the regulatory domain code. Currently this is MKK9_MKKC (0xfe).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds a helper function to ath/regd.c which can be asked if 4.9GHz channels
are allowed for a given regulatory domain code. This keeps the knowledge of
regdomains and defines like MKK9_MKKC in one place. I'm passing the regdomain
code instead of the ath_regulatory structure because this needs to be called
quite early in the driver inititalization where ath_regulatory is not available
yet in ath5k.
I'm using MKK9_MKKC only because this is the regdomain in the 802.11j enabled
sample cards we got from our vendor. I found some hints in HAL code that this
is used by Atheros to indicate 4.9GHz channels support and that there might be
other domain codes as well, but as I don't have any documentation I'm just
putting in what I need right now. It can be extended later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Shorten some lines and make code more readable.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.
ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.
One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.
Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.
By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx
|
|
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Update maintainer's email address, webpage and align with renaming of
files.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.
Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"mac80211 will properly assign sequence numbers to QoS-data
frames but cannot do so correctly for non-QoS-data and
management frames because beacons need them from that counter
as well and mac80211 cannot guarantee proper sequencing."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
