| Age | Commit message (Collapse) | Author |
|---|
|
Spotted after a code review.
Introduced by c12b395a46646bab69089ce7016ac78177f6001f (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.
For example:
~# ifconfig eth0 down
~# echo disk > /sys/power/state
<trigger a restore from hibernation>
~# ifconfig eth0 up
SIOCSIFFLAGS: No such device
This happens because the restore function bails out early upon
finding devices that were not up at hibernation. In doing so,
it never gets to the netif_device_attach call at the end of
the restore function. Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when something goes wrong, a flood of these messages can be
generated by usbnet (thousands per second). This doesn't
generally *help* the condition so this patch ratelimits the
rate of their generation.
There's an underlying problem in usbnet's kevent deferral
mechanism which needs fixing, specifically that events *can*
get dropped and not handled. This patch doesn't address this,
but just mitigates fallout caused by the current implemention.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As documented in RFC4861 (Neighbor Discovery for IP version 6) 7.2.6.,
unsolicited neighbour advertisements should be sent to the all-nodes
multicast address.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes (again) from Dave Airlie:
"dropped the ball on a vmware patch, so two more fixes for vmwgfx are
here, one for hibernate issue, one for a BUG trigger."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix a case where the code would BUG when trying to pin GMR memory
drm/vmwgfx: Fix hibernation device reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Power management:
- PCI/PM: Fix proc config reg access for D3cold and bridge
suspending
- PCI/PM: Resume device before shutdown
- PCI/PM: Fix deadlock when unbinding device if parent in D3cold
Hotplug:
- PCI/portdrv: Don't create hotplug slots unless port supports
hotplug"
* tag '3.7-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/portdrv: Don't create hotplug slots unless port supports hotplug
PCI/PM: Fix proc config reg access for D3cold and bridge suspending
PCI/PM: Resume device before shutdown
PCI/PM: Fix deadlock when unbinding device if parent in D3cold
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- sdhci: fix a NULL dereference at resume-time, seen on OLPC XO-4
- sdhci: fix against 3.7-rc1 for UHS modes without a vqmmc regulator
- sdhci-of-esdhc: disable CMD23 on boards where it's broken
- sdhci-s3c: fix against 3.7-rc1 for card detection with runtime PM
- dw_mmc, omap_hsmmc: fix potential NULL derefs, compiler warnings
* tag 'mmc-fixes-for-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: sdhci-s3c: fix the card detection in runtime-pm
mmc: sdhci-s3c: use clk_prepare_enable and clk_disable_unprepare
mmc: dw_mmc: constify dw_mci_idmac_ops in exynos back-end
mmc: dw_mmc: fix modular build for exynos back-end
mmc: sdhci: fix NULL dereference in sdhci_request() tuning
mmc: sdhci: fix IS_ERR() checking of regulator_get()
mmc: fix sdhci-dove probe/removal
mmc: sh_mmcif: fix use after free
mmc: sdhci-pci: fix 'Invalid iomem size' error message condition
mmc: mxcmmc: Fix MODULE_ALIAS
mmc: omap_hsmmc: fix NULL pointer dereference for dt boot
mmc: omap_hsmmc: fix host reference after mmc_free_host
mmc: dw_mmc: fix multiple drv_data NULL dereferences
mmc: dw_mmc: enable controller interrupt before calling mmc_start_host
mmc: sdhci-of-esdhc: disable CMD23 for some Freescale SoCs
mmc: dw_mmc: remove _dev_info compile warning
mmc: dw_mmc: convert the variable type of irq
|
|
Pull crypto fix from Herbert Xu:
"This push fixes a potential panic in cryptd which may occur with
crypto drivers such as aesni-intel."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cryptd - disable softirqs in cryptd_queue_worker to prevent data corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of commits are for stable and regression fixes. Except for one
fix for a regression in 3.7-rc4, there are all driver local changes,
so nothing too much to worry."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Fix card refcount unbalance
ALSA: hda - Add new codec ALC668 and ALC900 (default name ALC1150)
ALSA: hda - Improve HP depop when system enter to S3
ALSA: usb-audio: Fix crash at re-preparing the PCM stream
ALSA: hdspm - Fix sync check reporting on RME RayDAT
ALSA: hda - Add pin fixups for ASUS G75
ALSA: hda - Fix invalid connections in VT1802 codec
ALSA: hda - Fix empty DAC filling in patch_via.c
ALSA: hda - Force to reset IEC958 status bits for AD codecs
ALSA: es1968: Add ESS vendor ID to pm_whitelist
ALSA: HDA: Mark CS260x immutable structures const
ALSA: HDA: Fix digital microphone on CS420x
ALSA: hda: Cirrus: Fix coefficient index for beep configuration
ALSA: hda - support Teradici 2200 host card audio
ALSA: Fix typo in drivers sound
|
|
The commit 911dec0db4de6ccc544178a8ddaf9cec0a11d533
"xen/arm: Fix compile errors when drivers are compiled as modules." exports
the neccessary functions. But to guard ourselves against out-of-tree modules
and future drivers hitting this, lets export all of the relevant
hypercalls.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable@vger.kernel.org
Cc: linux-graphics-maintainer@vmware.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The device would not reset properly when resuming from hibernation.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable@vger.kernel.org
Cc: linux-graphics-maintainer@vmware.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- A set of SPEAr pinctrl fixes that recently arrived
- A fixup for the Samsung/Exynos Kconfig deps
* tag 'pinctrl-for-v3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung and exynos need to depend on OF && GPIOLIB
pinctrl: SPEAr1340: Add clcd sleep mode pin configuration
pinctrl: SPEAr1340: Make DDR reset & clock pads as gpio
pinctrl: SPEAr1310: add register entries for enabling pad direction
pinctrl: SPEAr1310: Separate out pci pins from pcie_sata pin group
pinctrl: SPEAr1310: Fix value of PERIP_CFG reigster and MCIF_SEL_SHIFT
pinctrl: SPEAr1310: fix clcd high resolution pin group name
pinctrl: SPEAr320: Correct pad mux entries for rmii/smii
pinctrl: SPEAr3xx: correct register space to configure pwm
pinctrl: SPEAr: Don't update all non muxreg bits on pinctrl_disable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes. I keep the fingers crossed that we now got
transparent huge pages ready for prime time."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: fix length calculation in idset.c
s390/sclp: fix addressing mode clobber
s390: Move css limits from drivers/s390/cio/ to include/asm/.
s390/thp: respect page protection in pmd_none() and pmd_present()
s390/mm: use pmd_large() instead of pmd_huge()
s390/cio: suppress 2nd path verification during resume
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"This reverts a patch that causes regression in binding between HID
devices and drivers during device unplug/replug cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hidraw: put old deallocation mechanism in place
|
|
Merge misc fixes from Andrew Morton:
"Five fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (5 patches)
h8300: add missing L1_CACHE_SHIFT
mm: bugfix: set current->reclaim_state to NULL while returning from kswapd()
fanotify: fix missing break
revert "epoll: support for disabling items, and a self-test app"
checkpatch: improve network block comment style checking
|
|
Pull drm fixes from Dave Airlie:
"Just radeon and nouveau, mostly regressions fixers, and a couple of
radeon register checker fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix acpi edid retrieval
drm/nvc0/disp: fix regression in vblank semaphore release
drm/nv40/mpeg: fix context handling
drm/nv40/graph: fix typo in type names
drm/nv41/vm: fix typo in type name
drm/radeon/si: add some missing regs to the VM reg checker
drm/radeon/cayman: add some missing regs to the VM reg checker
drm/radeon/dce3: switch back to old pll allocation order for discrete
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio and module fixes from Rusty Russell:
"YA module signing build tweak, and two cc'd to stable."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio: Don't access index after unregister.
modules: don't break modules_install on external modules with no key.
module: fix out-by-one error in kallsyms
|
|
Pull xfs bugfixes from Ben Myers:
- fix for large transactions spanning multiple iclog buffers
- zero the allocation_args structure on the stack before using it to
determine whether to use a worker for allocation
- move allocation stack switch to xfs_bmapi_allocate in order to
prevent deadlock on AGF buffers
- growfs no longer reads in garbage for new secondary superblocks
- silence a build warning
- ensure that invalid buffers never get written to disk while on free
list
- don't vmap inode cluster buffers during free
- fix buffer shutdown reference count mismatch
- fix reading of wrapped log data
* tag 'for-linus-v3.7-rc5' of git://oss.sgi.com/xfs/xfs:
xfs: fix reading of wrapped log data
xfs: fix buffer shudown reference count mismatch
xfs: don't vmap inode cluster buffers during free
xfs: invalidate allocbt blocks moved to the free list
xfs: silence uninitialised f.file warning.
xfs: growfs: don't read garbage for new secondary superblocks
xfs: move allocation stack switch up to xfs_bmapi_allocate
xfs: introduce XFS_BMAPI_STACK_SWITCH
xfs: zero allocation_args on the kernel stack
xfs: only update the last_sync_lsn when a transaction completes
|
|
Fix the build error
lib/atomic64.c: In function 'lock_addr':
lib/atomic64.c:40:11: error: 'L1_CACHE_SHIFT' undeclared (first use in this function)
lib/atomic64.c:40:11: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In kswapd(), set current->reclaim_state to NULL before returning, as
current->reclaim_state holds reference to variable on kswapd()'s stack.
In rare cases, while returning from kswapd() during memory offlining,
__free_slab() and freepages() can access the dangling pointer of
current->reclaim_state.
Signed-off-by: Takamori Yamaguchi <takamori.yamaguchi@jp.sony.com>
Signed-off-by: Aaditya Kumar <aaditya.kumar@ap.sony.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Anders Blomdell noted in 2010 that Fanotify lost events and provided a
test case. Eric Paris confirmed it was a bug and posted a fix to the
list
https://groups.google.com/forum/?fromgroups=#!topic/linux.kernel/RrJfTfyW2BE
but never applied it. Repeated attempts over time to actually get him
to apply it have never had a reply from anyone who has raised it
So apply it anyway
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: Eric Paris <eparis@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert commit 03a7beb55b9f ("epoll: support for disabling items, and a
self-test app") pending resolution of the issues identified by Michael
Kerrisk, copied below.
We'll revisit this for 3.8.
: I've taken a look at this patch as it currently stands in 3.7-rc1, and
: done a bit of testing. (By the way, the test program
: tools/testing/selftests/epoll/test_epoll.c does not compile...)
:
: There are one or two places where the behavior seems a little strange,
: so I have a question or two at the end of this mail. But other than
: that, I want to check my understanding so that the interface can be
: correctly documented.
:
: Just to go though my understanding, the problem is the following
: scenario in a multithreaded application:
:
: 1. Multiple threads are performing epoll_wait() operations,
: and maintaining a user-space cache that contains information
: corresponding to each file descriptor being monitored by
: epoll_wait().
:
: 2. At some point, a thread wants to delete (EPOLL_CTL_DEL)
: a file descriptor from the epoll interest list, and
: delete the corresponding record from the user-space cache.
:
: 3. The problem with (2) is that some other thread may have
: previously done an epoll_wait() that retrieved information
: about the fd in question, and may be in the middle of using
: information in the cache that relates to that fd. Thus,
: there is a potential race.
:
: 4. The race can't solved purely in user space, because doing
: so would require applying a mutex across the epoll_wait()
: call, which would of course blow thread concurrency.
:
: Right?
:
: Your solution is the EPOLL_CTL_DISABLE operation. I want to
: confirm my understanding about how to use this flag, since
: the description that has accompanied the patches so far
: has been a bit sparse
:
: 0. In the scenario you're concerned about, deleting a file
: descriptor means (safely) doing the following:
: (a) Deleting the file descriptor from the epoll interest list
: using EPOLL_CTL_DEL
: (b) Deleting the corresponding record in the user-space cache
:
: 1. It's only meaningful to use this EPOLL_CTL_DISABLE in
: conjunction with EPOLLONESHOT.
:
: 2. Using EPOLL_CTL_DISABLE without using EPOLLONESHOT in
: conjunction is a logical error.
:
: 3. The correct way to code multithreaded applications using
: EPOLL_CTL_DISABLE and EPOLLONESHOT is as follows:
:
: a. All EPOLL_CTL_ADD and EPOLL_CTL_MOD operations should
: should EPOLLONESHOT.
:
: b. When a thread wants to delete a file descriptor, it
: should do the following:
:
: [1] Call epoll_ctl(EPOLL_CTL_DISABLE)
: [2] If the return status from epoll_ctl(EPOLL_CTL_DISABLE)
: was zero, then the file descriptor can be safely
: deleted by the thread that made this call.
: [3] If the epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY,
: then the descriptor is in use. In this case, the calling
: thread should set a flag in the user-space cache to
: indicate that the thread that is using the descriptor
: should perform the deletion operation.
:
: Is all of the above correct?
:
: The implementation depends on checking on whether
: (events & ~EP_PRIVATE_BITS) == 0
: This replies on the fact that EPOLL_CTL_AD and EPOLL_CTL_MOD always
: set EPOLLHUP and EPOLLERR in the 'events' mask, and EPOLLONESHOT
: causes those flags (as well as all others in ~EP_PRIVATE_BITS) to be
: cleared.
:
: A corollary to the previous paragraph is that using EPOLL_CTL_DISABLE
: is only useful in conjunction with EPOLLONESHOT. However, as things
: stand, one can use EPOLL_CTL_DISABLE on a file descriptor that does
: not have EPOLLONESHOT set in 'events' This results in the following
: (slightly surprising) behavior:
:
: (a) The first call to epoll_ctl(EPOLL_CTL_DISABLE) returns 0
: (the indicator that the file descriptor can be safely deleted).
: (b) The next call to epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY.
:
: This doesn't seem particularly useful, and in fact is probably an
: indication that the user made a logic error: they should only be using
: epoll_ctl(EPOLL_CTL_DISABLE) on a file descriptor for which
: EPOLLONESHOT was set in 'events'. If that is correct, then would it
: not make sense to return an error to user space for this case?
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paton J. Lewis" <palewis@adobe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some comment styles in net and drivers/net are flagged inappropriately.
Avoid proclaiming inline comments like:
int a = b; /* some comment */
and block comments like:
/*********************
* some comment
********************/
are defective.
Tested with
$ cat drivers/net/t.c
/* foo */
/*
* foo
*/
/* foo
*/
/* foo
* bar */
/****************************
* some long block comment
***************************/
struct foo {
int bar; /* another test */
};
$
Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
just some misc regression fixes and typo fixes.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: fix acpi edid retrieval
drm/nvc0/disp: fix regression in vblank semaphore release
drm/nv40/mpeg: fix context handling
drm/nv40/graph: fix typo in type names
drm/nv41/vm: fix typo in type name
|
|
Virtio wants to release used indices after the corresponding
virtio device has been unregistered. However, virtio does not
hold an extra reference, giving up its last reference with
device_unregister(), making accessing dev->index afterwards
invalid.
I actually saw problems when testing my (not-yet-merged)
virtio-ccw code:
- device_add virtio-net,id=xxx
-> creates device virtio<n> with n>0
- device_del xxx
-> deletes virtio<n>, but calls ida_simple_remove with an
index of 0
- device_add virtio-net,id=xxx
-> tries to add virtio0, which is still in use...
So let's save the index we want to release before calling
device_unregister().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Commit c0077061e7ea accidentally inverted the logic for nouveau_acpi_edid,
causing it to only show a connector as connected when the edid could not
be retrieved with acpi.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Kelly Doran <kel.p.doran@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
It slipped in thanks to typeless API.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
nv04_graph_priv / nv04_graph_chan are not defined in this context...
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
It's a miracle it compiles at all - nv04_vm_priv does not exist
anywhere in the tree.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
into drm-fixes
Just some minor fixes for VM reg check and a regression fix for dce3 plls
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/si: add some missing regs to the VM reg checker
drm/radeon/cayman: add some missing regs to the VM reg checker
drm/radeon/dce3: switch back to old pll allocation order for discrete
|
|
Commit 4439647 ("xfs: reset buffer pointers before freeing them") in
3.0-rc1 introduced a regression when recovering log buffers that
wrapped around the end of log. The second part of the log buffer at
the start of the physical log was being read into the header buffer
rather than the data buffer, and hence recovery was seeing garbage
in the data buffer when it got to the region of the log buffer that
was incorrectly read.
Cc: <stable@vger.kernel.org> # 3.0.x, 3.2.x, 3.4.x 3.6.x
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
When we shut down the filesystem, we have to unpin and free all the
buffers currently active in the CIL. To do this we unpin and remove
them in one operation as a result of a failed iclogbuf write. For
buffers, we do this removal via a simultated IO completion of after
marking the buffer stale.
At the time we do this, we have two references to the buffer - the
active LRU reference and the buf log item. The LRU reference is
removed by marking the buffer stale, and the active CIL reference is
by the xfs_buf_iodone() callback that is run by
xfs_buf_do_callbacks() during ioend processing (via the bp->b_iodone
callback).
However, ioend processing requires one more reference - that of the
IO that it is completing. We don't have this reference, so we free
the buffer prematurely and use it after it is freed. For buffers
marked with XBF_ASYNC, this leads to assert failures in
xfs_buf_rele() on debug kernels because the b_hold count is zero.
Fix this by making sure we take the necessary IO reference before
starting IO completion processing on the stale buffer, and set the
XBF_ASYNC flag to ensure that IO completion processing removes all
the active references from the buffer to ensure it is fully torn
down.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Inode buffers do not need to be mapped as inodes are read or written
directly from/to the pages underlying the buffer. This fixes a
regression introduced by commit 611c994 ("xfs: make XBF_MAPPED the
default behaviour").
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
When we free a block from the alloc btree tree, we move it to the
freelist held in the AGFL and mark it busy in the busy extent tree.
This typically happens when we merge btree blocks.
Once the transaction is committed and checkpointed, the block can
remain on the free list for an indefinite amount of time. Now, this
isn't the end of the world at this point - if the free list is
shortened, the buffer is invalidated in the transaction that moves
it back to free space. If the buffer is allocated as metadata from
the free list, then all the modifications getted logged, and we have
no issues, either. And if it gets allocated as userdata direct from
the freelist, it gets invalidated and so will never get written.
However, during the time it sits on the free list, pressure on the
log can cause the AIL to be pushed and the buffer that covers the
block gets pushed for write. IOWs, we end up writing a freed
metadata block to disk. Again, this isn't the end of the world
because we know from the above we are only writing to free space.
The problem, however, is for validation callbacks. If the block was
on old btree root block, then the level of the block is going to be
higher than the current tree root, and so will fail validation.
There may be other inconsistencies in the block as well, and
currently we don't care because the block is in free space. Shutting
down the filesystem because a freed block doesn't pass write
validation, OTOH, is rather unfriendly.
So, make sure we always invalidate buffers as they move from the
free space trees to the free list so that we guarantee they never
get written to disk while on the free list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Phil White <pwhite@sgi.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Uninitialised variable build warning introduced by 2903ff0 ("switch
simple cases of fget_light to fdget"), gcc is not smart enough to
work out that the variable is not used uninitialised, and the commit
removed the initialisation at declaration that the old variable had.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
When updating new secondary superblocks in a growfs operation, the
superblock buffer is read from the newly grown region of the
underlying device. This is not guaranteed to be zero, so violates
the underlying assumption that the unused parts of superblocks are
zero filled. Get a new buffer for these secondary superblocks to
ensure that the unused regions are zero filled correctly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Switching stacks are xfs_alloc_vextent can cause deadlocks when we
run out of worker threads on the allocation workqueue. This can
occur because xfs_bmap_btalloc can make multiple calls to
xfs_alloc_vextent() and even if xfs_alloc_vextent() fails it can
return with the AGF locked in the current allocation transaction.
If we then need to make another allocation, and all the allocation
worker contexts are exhausted because the are blocked waiting for
the AGF lock, holder of the AGF cannot get it's xfs-alloc_vextent
work completed to release the AGF. Hence allocation effectively
deadlocks.
To avoid this, move the stack switch one layer up to
xfs_bmapi_allocate() so that all of the allocation attempts in a
single switched stack transaction occur in a single worker context.
This avoids the problem of an allocation being blocked waiting for
a worker thread whilst holding the AGF.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Certain allocation paths through xfs_bmapi_write() are in situations
where we have limited stack available. These are almost always in
the buffered IO writeback path when convertion delayed allocation
extents to real extents.
The current stack switch occurs for userdata allocations, which
means we also do stack switches for preallocation, direct IO and
unwritten extent conversion, even those these call chains have never
been implicated in a stack overrun.
Hence, let's target just the single stack overun offended for stack
switches. To do that, introduce a XFS_BMAPI_STACK_SWITCH flag that
the caller can pass xfs_bmapi_write() to indicate it should switch
stacks if it needs to do allocation.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Zero the kernel stack space that makes up the xfs_alloc_arg structures.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
The log write code stamps each iclog with the current tail LSN in
the iclog header so that recovery knows where to find the tail of
thelog once it has found the head. Normally this is taken from the
first item on the AIL - the log item that corresponds to the oldest
active item in the log.
The problem is that when the AIL is empty, the tail lsn is dervied
from the the l_last_sync_lsn, which is the LSN of the last iclog to
be written to the log. In most cases this doesn't happen, because
the AIL is rarely empty on an active filesystem. However, when it
does, it opens up an interesting case when the transaction being
committed to the iclog spans multiple iclogs.
That is, the first iclog is stamped with the l_last_sync_lsn, and IO
is issued. Then the next iclog is setup, the changes copied into the
iclog (takes some time), and then the l_last_sync_lsn is stamped
into the header and IO is issued. This is still the same
transaction, so the tail lsn of both iclogs must be the same for log
recovery to find the entire transaction to be able to replay it.
The problem arises in that the iclog buffer IO completion updates
the l_last_sync_lsn with it's own LSN. Therefore, If the first iclog
completes it's IO before the second iclog is filled and has the tail
lsn stamped in it, it will stamp the LSN of the first iclog into
it's tail lsn field. If the system fails at this point, log recovery
will not see a complete transaction, so the transaction will no be
replayed.
The fix is simple - the l_last_sync_lsn is updated when a iclog
buffer IO completes, and this is incorrect. The l_last_sync_lsn
shoul dbe updated when a transaction is completed by a iclog buffer
IO. That is, only iclog buffers that have transaction commit
callbacks attached to them should update the l_last_sync_lsn. This
means that the last_sync_lsn will only move forward when a commit
record it written, not in the middle of a large transaction that is
rolling through multiple iclog buffers.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Booting on a system with all of its memory above the 4GB boundary breaks
for two reasons:
(1) We still try to create a non-empty DMA32 zone
(2) no-bootmem limits allocations to 0xffffffff
This patch fixes these issues for ARM64.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit 149c24151e85 ("ARM: SMP: use a timing out completion for cpu
hotplug") modified arm's CPU up path to use completions. It seems that
we only got half of this patch for arm64, so add the missing call to
complete.
Reported-by: Jon Brawn <jon.brawn@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit c1d7e01d7877 ("ipc: use Kconfig options for
__ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION") replaced the
__ARCH_WANT_COMPAT_IPC_PARSE_VERSION token with a corresponding Kconfig
option instead.
This patch updates arm64 to use the latter, rather than #define an
unused token.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
struct user_fp does not exist for arm64, so use struct user_fpsimd_state
instead for the ELF core dumping definitions. Furthermore, since we use
regset-based core dumping, we do not need definitions for dump_task_regs
and dump_fpu.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We currently use a fake event encoding (0xFF) to indicate CPU cycles so
that we don't waste an event counter and can target the hardware cycle
counter instead.
The problem with this approach is that the event space defined by the
architecture permits an implementation to allocate 0xFF for some other
event.
This patch uses the architected cycle counter encoding (0x11) so that
we avoid potentially clashing with event encodings on future CPU
implementations.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This register is needed for streamout to work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
|
|
These regs were being wronly rejected leading to rendering
issues.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=56876
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
|
|
There are uncovered cases whether the card refcount introduced by the
commit a0830dbd isn't properly increased or decreased:
- OSS PCM and mixer success paths
- When lookup function gets NULL
This patch fixes these places.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50251
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
