| Age | Commit message (Collapse) | Author |
|---|
|
into drm-next
Alex writes:
Radeon fixes pull. Not much to it.
- fix some splatter if the interrupt handler isn't registered
- Add a quirk for an old R200 board to fix washed out colors on the DAC
- Don't try and soft reset the MC when we reset the GPU. It usually doesn't
need it and doesn't always work reliably.
- A CS checker fix from Marek
* 'drm-fixes-3.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
|
|
Pull ARM fixes from Russell King:
"Mainly a group of fixes, the only exception is the wiring up of the
kcmp syscall now that those patches went in during the last merge
window."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7668/1: fix memset-related crashes caused by recent GCC (4.7.2) optimizations
ARM: 7667/1: perf: Fix section mismatch on armpmu_init()
ARM: 7666/1: decompressor: add -mno-single-pic-base for building the decompressor
ARM: 7665/1: Wire up kcmp syscall
ARM: 7664/1: perf: remove erroneous semicolon from event initialisation
ARM: 7663/1: perf: fix ARMv7 EVTYPE_MASK to include NSH bit
ARM: 7662/1: hw_breakpoint: reset debug logic on secondary CPUs in s2ram resume
ARM: 7661/1: mm: perform explicit branch predictor maintenance when required
ARM: 7660/1: tlb: add branch predictor maintenance operations
ARM: 7659/1: mm: make mm->context.id an atomic64_t variable
ARM: 7658/1: mm: fix race updating mm->context.id on ASID rollover
ARM: 7657/1: head: fix swapper and idmap population with LPAE and big-endian
ARM: 7655/1: smp_twd: make twd_local_timer_of_register() no-op for nosmp
ARM: 7652/1: mm: fix missing use of 'asid' to get asid value from mm->context.id
ARM: 7642/1: netx: bump IRQ offset to 64
|
|
EFI changes for v3.9-rc2,
* Make the EFI variable code more paranoid about running out of
space in NVRAM, since this is the root cause of the recent issue
where machines refuse to boot - from Matthew Garrett.
* Some efivarfs patches that fix regressions introduced in v3.9-rc1.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
kernel_map_sync_memtype() is called from a variety of contexts. The
pat.c code that calls it seems to ensure that it is not called for
non-ram areas by checking via pat_pagerange_is_ram(). It is important
that it only be called on the actual identity map because there *IS*
no map to sync for highmem pages, or for memory holes.
The ioremap.c uses are not as careful as those from pat.c, and call
kernel_map_sync_memtype() on PCI space which is in the middle of the
kernel identity map _range_, but is not actually mapped.
This patch adds a check to kernel_map_sync_memtype() which probably
duplicates some of the checks already in pat.c. But, it is necessary
for the ioremap.c uses and shouldn't hurt other callers.
I have reproduced this bug and this patch fixes it for me and the
original bug reporter:
https://lkml.org/lkml/2013/2/5/396
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130307163151.D9B58C4E@kernel.stglabs.ibm.com
Signed-off-by: Dave Hansen <dave@sr71.net>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small things here and there, nothing major here really. The
conversion of twl4030ldo_ops to get_voltage_sel is a fix, as covered
in the commit log it fixes inconsistency in handling of the IS_UNSUP()
feature in the driver."
* tag 'regulator-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fixed regulator_bulk_enable unwinding code
regulator: twl: Convert twl4030ldo_ops to get_voltage_sel
regulator: palmas: fix number of SMPS voltages
regulator: core: fix documentation error in regulator_allow_bypass
regulator: core: update kernel documentation for regulator_desc
regulator: db8500-prcmu - remove incorrect __exit markup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap PM fix from Mark Brown:
"A simple fix to stop us leaking a runtime PM reference in the case
where we fail to enable a device."
* tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: call pm_runtime_put in pm_runtime_get_sync failed case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Minor code cleanups and new Kconfig option to disable /dev/ecryptfs
The code cleanups fix up W=1 compiler warnings and some unnecessary
checks. The new Kconfig option, defaulting to N, allows the rarely
used eCryptfs kernel to userspace communication channel to be compiled
out. This may be the first step in it being eventually removed."
Hmm. I'm not sure whether these should be called "fixes", and it
probably should have gone in the merge window. But I'll let it slide.
* tag 'ecryptfs-3.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: allow userspace messaging to be disabled
eCryptfs: Fix redundant error check on ecryptfs_find_daemon_by_euid()
ecryptfs: ecryptfs_msg_ctx_alloc_to_free(): remove kfree() redundant null check
eCryptfs: decrypt_pki_encrypted_session_key(): remove kfree() redundant null check
eCryptfs: remove unneeded checks in virt_to_scatterlist()
eCryptfs: Fix -Wmissing-prototypes warnings
eCryptfs: Fix -Wunused-but-set-variable warnings
eCryptfs: initialize payload_len in keystore.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon patches from Guenter Roeck:
"Bug fixes for sht15 and ltc2978 driver plus some documentation
updates"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (sht15) Check return value of regulator_enable()
hwmon: (adt7410) Document ADT7420 support
hwmon: (pmbus/ltc2978) Use detected chip ID to select supported functionality
hwmon: (pmbus/ltc2978) Fix peak attribute handling
hwmon: (pmbus/ltc2978) Update datasheet links
hwmon: Update my e-mail address in driver documentation
|
|
The MIP_ADDRESS state has 2 meanings. If the texture has one sample
per pixel, it's a pointer to the mipmap chain. If the texture has
multiple samples per pixel, it's a pointer to FMASK, a metadata buffer
needed for reading compressed MSAA textures. The mipmap
alignment rules do not apply to FMASK.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The MC is mostly likely busy (e.g., display requests), not hung
so no need to reset it. Doing an MC reset is tricky and not
particularly reliable. Fixes hangs in certain cases.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
vbios values are wrong leading to colors that are
too bright. Use the default values instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Avoids splatter if the interrupt handler is not registered due
to acceleration being disabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
|
|
optimizations
Recent GCC versions (e.g. GCC-4.7.2) perform optimizations based on
assumptions about the implementation of memset and similar functions.
The current ARM optimized memset code does not return the value of
its first argument, as is usually expected from standard implementations.
For instance in the following function:
void debug_mutex_lock_common(struct mutex *lock, struct mutex_waiter *waiter)
{
memset(waiter, MUTEX_DEBUG_INIT, sizeof(*waiter));
waiter->magic = waiter;
INIT_LIST_HEAD(&waiter->list);
}
compiled as:
800554d0 <debug_mutex_lock_common>:
800554d0: e92d4008 push {r3, lr}
800554d4: e1a00001 mov r0, r1
800554d8: e3a02010 mov r2, #16 ; 0x10
800554dc: e3a01011 mov r1, #17 ; 0x11
800554e0: eb04426e bl 80165ea0 <memset>
800554e4: e1a03000 mov r3, r0
800554e8: e583000c str r0, [r3, #12]
800554ec: e5830000 str r0, [r3]
800554f0: e5830004 str r0, [r3, #4]
800554f4: e8bd8008 pop {r3, pc}
GCC assumes memset returns the value of pointer 'waiter' in register r0; causing
register/memory corruptions.
This patch fixes the return value of the assembly version of memset.
It adds a 'mov' instruction and merges an additional load+store into
existing load/store instructions.
For ease of review, here is a breakdown of the patch into 4 simple steps:
Step 1
======
Perform the following substitutions:
ip -> r8, then
r0 -> ip,
and insert 'mov ip, r0' as the first statement of the function.
At this point, we have a memset() implementation returning the proper result,
but corrupting r8 on some paths (the ones that were using ip).
Step 2
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 1:
save r8:
- str lr, [sp, #-4]!
+ stmfd sp!, {r8, lr}
and restore r8 on both exit paths:
- ldmeqfd sp!, {pc} @ Now <64 bytes to go.
+ ldmeqfd sp!, {r8, pc} @ Now <64 bytes to go.
(...)
tst r2, #16
stmneia ip!, {r1, r3, r8, lr}
- ldr lr, [sp], #4
+ ldmfd sp!, {r8, lr}
Step 3
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 0:
save r8:
- stmfd sp!, {r4-r7, lr}
+ stmfd sp!, {r4-r8, lr}
and restore r8 on both exit paths:
bgt 3b
- ldmeqfd sp!, {r4-r7, pc}
+ ldmeqfd sp!, {r4-r8, pc}
(...)
tst r2, #16
stmneia ip!, {r4-r7}
- ldmfd sp!, {r4-r7, lr}
+ ldmfd sp!, {r4-r8, lr}
Step 4
======
Rewrite register list "r4-r7, r8" as "r4-r8".
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
hid_output_raw_report() makes a direct call to usb_control_msg(). However,
some USB3 boards have shown that the usb device is not ready during the
.probe(). This blocks the entire usb device, and the paired mice, keyboards
are not functional. The dmesg output is the following:
[ 11.912287] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 11.912537] logitech-djreceiver 0003:046D:C52B.0003: logi_dj_probe:logi_dj_recv_query_paired_devices error:-32
[ 11.912636] logitech-djreceiver: probe of 0003:046D:C52B.0003 failed with error -32
Relying on the scheduled call to usbhid_submit_report() fixes the problem.
related bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1072082
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1039143
https://bugzilla.redhat.com/show_bug.cgi?id=840391
https://bugzilla.kernel.org/show_bug.cgi?id=49781
Reported-and-tested-by: Bob Bowles <bobjohnbowles@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Set card->private_data in snd_ice1712_create for fixing NULL
dereference in snd_ice1712_remove().
Signed-off-by: Sean Connor <sconnor004@allyinics.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The delayed inode code batches up changes to the btree in hopes of doing
them in bulk. As the changes build up, processes kick off worker
threads and wait for them to make progress.
The current code kicks off an async work queue item for each delayed
node, which creates a lot of churn. It also uses a fixed 1 HZ waiting
period for the throttle, which allows us to build a lot of pending
work and can slow down the commit.
This changes us to watch a sequence counter as it is bumped during the
operations. We kick off fewer work items and have each work item do
more work.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Add missing MODULE_ALIAS_FS("ocfs2") how did I miss that?
Remove unnecessary MODULE_ALIAS_FS("devpts") devpts can not be modular.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
It's compatible with ALC282.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the zero check `hda_frame_size_words == 0' before the modulus
`buffer_size_words % hda_frame_size_words'.
Also remove the redundant null check `buffer_addx == NULL'.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the new control cannot be created, this function will return to avoid
snd_hda_ctl_add dereferencing a NULL control pointer.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the SPDIF control array cannot be reallocated, the function
will return to avoid dereferencing a NULL pointer.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.9
A few driver fixes, none of them terribly dramatic.
|
|
|
|
|
|
|
|
|
|
If the sentinel triggers, we do not want the boot loader authors to
just poke it and make the error go away, we want them to actually fix
the problem.
This should help avoid making the incorrect change in non-compliant
bootloaders.
[ hpa: dropped the Documentation/x86/boot.txt hunk pending
clarifications ]
Signed-off-by: Peter Jones <pjones@redhat.com>
Link: http://lkml.kernel.org/r/1362592823-28967-1-git-send-email-pjones@redhat.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
When boot_params->sentinel is set, all we really know is that some
undefined set of fields in struct boot_params contain garbage. In the
particular case of efi_info, however, there is a private magic for
that substructure, so it is generally safe to leave it even if the
bootloader is broken.
kexec (for which we did the initial analysis) did not initialize this
field, but of course all the EFI bootloaders do, and most EFI
bootloaders are broken in this respect (and should be fixed.)
Reported-by: Robin Holt <holt@sgi.com>
Link: http://lkml.kernel.org/r/CA%2B5PVA51-FT14p4CRYKbicykugVb=PiaEycdQ57CK2km_OQuRQ@mail.gmail.com
Tested-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Henrik reported that his MacAir 3.1 would not boot with
| commit 8d57470d8f859635deffe3919d7d4867b488b85a
| Date: Fri Nov 16 19:38:58 2012 -0800
|
| x86, mm: setup page table in top-down
It turns out that we do not calculate the real_end properly:
We try to get 2M size with 4K alignment, and later will round down
to 2M, so we will get less then 2M for first mapping, in extreme
case could be only 4K only. In Henrik's system it has (1M-32K) as
last usable rage is [mem 0x7f9db000-0x7fef8fff].
The problem is exposed when EFI booting have several holes and it
will force mapping to use PTE instead as we only map usable areas.
To fix it, just make it be 2M aligned, so we can be guaranteed to be
able to use large pages to map it.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Bisected-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQX4nQ7_1kg5RL_vh56rmcSHXUi1ExrZX7CwED4NGMnHfg@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
The commit 27be457000211a6903968dfce06d5f73f051a217
('x86 idle: remove 32-bit-only "no-hlt" parameter, hlt_works_ok
flag') removed the hlt_works_ok flag from struct cpuinfo_x86, but
boot_cpu_data and new_cpu_data initializers were not changed
causing setting f00f_bug flag, instead of fdiv_bug.
If CONFIG_X86_F00F_BUG is not set the f00f_bug flag is never
cleared.
To avoid such problems in future C99-style initialization is now
used.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: len.brown@intel.com
Link: http://lkml.kernel.org/r/1362266082-2227-1-git-send-email-krzysiek@podlesie.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Raid56 merge (merge commit e942f88) had mistakenly removed a call to
__cancel_balance(), which resulted in balance not cleaning up after itself
after a successful finish. (Cleanup includes switching the state, removing
the balance item and releasing mut_ex_op testnset lock.) Bring it back.
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-next
A bunch of fixes, nothing truely horrible:
- Fix PCH irq handling race which resulted in missed gmbus/dp aux irqs
and subsequent fallout (Paulo)
- Fixup off-by-one in our hsw id table (Kenneth)
- Fixup ilk rc6 support (disabled by default), regression introduced in
3.8
- g4x plane w/a from Egbert Eich
- gen2/3/4 dpms suspend/standy fixes for VGA outputs from Patrik Jakobsson
- Workaround dying ivb machines with less aggressive rc6 values (Stéphane
Marchesin)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/i915: Fix Haswell/CRW PCI IDs.
drm/i915: Don't clobber crtc->fb when queue_flip fails
drm/i915: wait_event_timeout's timeout is in jiffies
drm/i915: Fix missing variable initilization
|
|
We had a recent fix to fix the release of pagecache pages when
cifs_writev_requeue writes fail. Unfortunately, it releases the page
before trying to unlock it. At that point, the page might be gone by the
time the unlock comes in.
Unlock the page first before checking the value of "rc", and only then
end writeback and release the pages. The page lock isn't required for
any of those operations so this should be safe.
Reported-by: Anton Altaparmakov <aia21@cam.ac.uk>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
...as promised for 3.9.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next into for-linus-3.9
|
|
cifs_rename_pending_delete() attempts to silly rename file using
CIFSSMBRenameOpenFile(). This uses the SET_FILE_INFORMATION TRANS2
command with information level set to the passthru info-level
SMB_SET_FILE_RENAME_INFORMATION.
We need to check to make sure that the server support passthru
info-levels before attempting the silly rename or else we will fail to
rename the file.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Fix check for error condition after setting attributes with
CIFSSMBSetFileInfo().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
WARNING: vmlinux.o(.text+0xfb80): Section mismatch in reference
from the function armpmu_register() to the function
.init.text:armpmu_init()
The function armpmu_register() references
the function __init armpmu_init().
This is often because armpmu_register lacks a __init
annotation or the annotation of armpmu_init is wrong.
Just drop the __init marking on armpmu_init() because
armpmu_register() no longer has an __init marking.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
decompressor
Before jumping to (position independent) C-code from the decompressor's
assembler world we set-up the C environment. This setup currently does not
set r9, which for arm-none-uclinux-uclibceabi toolchains is by default
expected to be the PIC offset base register (IE should point to the
beginning of the GOT).
Currently, therefore, in order to build working kernels that use the
decompressor it is necessary to use an arm-linux-gnueabi toolchain, or
similar. uClinux toolchains cause a prefetch abort to occur at the beginning
of the decompress_kernel function.
This patch allows uClinux toolchains to build bootable zImages by forcing
the -mno-single-pic-base option, which ensures that the location of the GOT
is re-derived each time it is required, and r9 becomes free for use as a
general purpose register.
This has a small (4% in instruction terms) advantage over the alternative of
setting r9 to point to the GOT before calling into the C-world.
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* pm-fixes:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
|
|
* acpi-fixes:
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
|
|
It seems some VMs support the P state MSRs but return zeros. Fail
gracefully if we are running in this environment.
References: https://bugzilla.redhat.com/show_bug.cgi?id=916833
Reported-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If cpufreq_register_driver() fails just free memory that has been
allocated and return. intel_pstate_exit() function is removed since we
are built-in only now there is no reason for a module exit procedure.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
According to PRM we need to disable hsync and vsync even though ADPA is
disabled. The previous code did infact do the opposite so we fix it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56359
Tested-by: max <manikulin@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Joseph was hitting a failure case when mounting efivarfs which
resulted in an incorrect error message,
$ sudo mount -v /sys/firmware/efi/efivars mount: Cannot allocate memory
triggered when efivarfs_valid_name() returned -EINVAL.
Make sure we pass accurate return values up the stack if
efivarfs_fill_super() fails to build inodes for EFI variables.
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Stricter validation was introduced with commit da27a24383b2b
("efivarfs: guid part of filenames are case-insensitive") and commit
47f531e8ba3b ("efivarfs: Validate filenames much more aggressively"),
which is necessary for the guid portion of efivarfs filenames, but we
don't need to be so strict with the first part, the variable name. The
UEFI specification doesn't impose any constraints on variable names
other than they be a NULL-terminated string.
The above commits caused a regression that resulted in users seeing
the following message,
$ sudo mount -v /sys/firmware/efi/efivars mount: Cannot allocate memory
whenever pstore EFI variables were present in the variable store,
since their variable names failed to pass the following check,
/* GUID should be right after the first '-' */
if (s - 1 != strchr(str, '-'))
as a typical pstore filename is of the form, dump-type0-10-1-<guid>.
The fix is trivial since the guid portion of the filename is GUID_LEN
bytes, we can use (len - GUID_LEN) to ensure the '-' character is
where we expect it to be.
(The bogus ENOMEM error value will be fixed in a separate patch.)
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
UEFI variables are typically stored in flash. For various reasons, avaiable
space is typically not reclaimed immediately upon the deletion of a
variable - instead, the system will garbage collect during initialisation
after a reboot.
Some systems appear to handle this garbage collection extremely poorly,
failing if more than 50% of the system flash is in use. This can result in
the machine refusing to boot. The safest thing to do for the moment is to
forbid writes if they'd end up using more than half of the storage space.
We can make this more finegrained later if we come up with a method for
identifying the broken machines.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Disable bits for ADPA HSYNC and VSYNC where mixed up resulting in suspend
becoming standby and vice versa. Fixed by swapping their bit position.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The number of DMA fault reasons in intel's document are from 1
to 0xD, but in dmar.c fault reason 0xD is not printed out.
In this document:
"Intel Virtualization Technology for Directed I/O Architecture Specification"
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
Chapter 4. Support For Device-IOTLBs
Table 6. Unsuccessful Translated Requests
There is fault reason for 0xD not listed in kernel:
Present context-entry used to process translation request
specifies blocking of Translation Requests (Translation Type (T)
field value not equal to 01b).
This patch adds reason 0xD as well.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Donald Dutile <ddutile@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Hannes Reinecke <hare@suse.de>
Link: http://lkml.kernel.org/r/1362537797-6034-1-git-send-email-zhen-hual@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
