| Age | Commit message (Collapse) | Author |
|---|
|
Current FC HBA queue_depth ramp up code depends on last queue
full time. The sdev already has last_queue_full_time field to
track last queue full time but stored value is truncated by
last four bits.
So this patch updates last_queue_full_time without truncating
last 4 bits to store full value and then updates its only
current usages in scsi_track_queue_full to ignore last four bits
to keep current usages same while also use this field
in added ramp up code.
Adds scsi_handle_queue_ramp_up to ramp up queue_depth on
successful completion of IO. The scsi_handle_queue_ramp_up will
do ramp up on all luns of a target, just same as ramp down done
on all luns on a target.
The ramp up is skipped in case the change_queue_depth is not
supported by LLD or already reached to added max_queue_depth.
Updates added max_queue_depth on every new update to default
queue_depth value.
The ramp up is also skipped if lapsed time since either last
queue ramp up or down is less than LLD specified
queue_ramp_up_period.
Adds queue_ramp_up_period to sysfs but only if change_queue_depth
is supported since ramp up and queue_ramp_up_period is needed only
in case change_queue_depth is supported first.
Initializes queue_ramp_up_period to 120HZ jiffies as initial
default value, it is same as used in existing lpfc and qla2xxx.
-v2
Combined all ramp code into this single patch.
-v3
Moves max_queue_depth initialization after slave_configure is
called from after slave_alloc calling done. Also adjusted
max_queue_depth check to skip ramp up if current queue_depth
is >= max_queue_depth.
-v4
Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f
to store or show its value.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Tested-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The cmd_per_lun value is used by scsi-ml as fall back lowest
queue_depth value but in case of libfc cmd_per_lun is set to
same value as max queue_depth = 32.
So this patch reduces cmd_per_lun value to 3 and configures
each lun with default max queue_depth 32 in fc_slave_alloc.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This converts the libfc using scsi_track_queue_full to
track the queue full from the change_queue_depth callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This has scsi-ml call the change_queue_depth functions when
we get a QUEUE_FULL. It will only change the queue depth if
change_queue_depth is set because the LLD may have to
modify some internal resources, so I thought this would
be the safest route.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
-v2
Limits change_queue_depth to only all luns of target by adding
channel check while iterating for all luns of Scsi_Host. This is
same as currently qla2xxx FC HBA does on QUEUE_FULL event.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch adds support for ring based wrbs
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch enables msix for be2iscsi. It also enables use
of mcc_rings for fw commands. Since the mcc eq creation is
dependent on msix I am sending as one patch
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Timer crashes were caused by freeing a struct fc_rport_priv
with a timer pending, causing the timer facility list to be
corrupted. This was during FC uplink flap tests with a lot
of targets.
After discovery, we were doing an PLOGI on an rdata that was
in DELETE state but not yet removed from the lookup list.
This moved the rdata from DELETE state to PLOGI state.
If the PLOGI exchange allocation failed and needed to be
retried, the timer scheduling could race with the free
being done by fc_rport_work().
When fc_rport_login() is called on a rport in DELETE state,
move it to a new state RESTART. In fc_rport_work, when
handling a LOGO, STOPPED or FAILED event, look for restart
state. In the RESTART case, don't take the rdata off the
list and after the transport remote port is deleted and
exchanges are reset, re-login to the remote port.
Note that the new RESTART state also corrects a problem we
had when re-discovering a port that had moved to DELETE state.
In that case, a new rdata was created, but the old rdata
would do an exchange manager reset affecting the FC_ID
for both the new rdata and old rdata. With the new state,
the new port isn't logged into until after any old exchanges
are reset.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Driver was processing a fixed max number of cq descriptors per ISR. For
instance, for the SCSI IO queue, number of IOs processed per ISR were 8.
If hardware writes 9 cq descriptors to the cq and generates an interrupt,
driver would process only 8 descriptors and decrement the outstanding
credit count by 8. Unless another interrupt event happens, the hw does
not generate any additional interrupt. This results in the cq descriptor
sitting in the queue without being procesed and can cause IO timeouts
and aborts.
Modify all ISR functions to process all queued cq descriptors in one shot.
Since bulk of ELS frame processing is done in thread context and bulk
of SCSI IO processing is done in soft ISR deferred context, the cycles
spent in the ISR per cq descriptor is small.
Signed-off-by: Herman Lee <hermlee@cisco.com>
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
handling
I was running into several different panics under stress, which I traced down
to a few different possible slab corruption issues in error handling paths.
I have not yet looked into why these exchange sends fail, but with these
fixes my test system is much more stable under stress than before.
fc_elsct_send() could fail and either leave the passed in frame intact
(failure in fc_ct/els_fill) or the frame could have been freed if the
failure was is fc_exch_seq_send(). The caller had no way of knowing, and
there was a potential double free in the error handling in fc_fcp_rec().
Make fc_elsct_send() always free the frame before returning, and remove the
fc_frame_free() call in fc_fcp_rec().
While fc_exch_seq_send() did always consume the frame, there were double free
bugs in the error handling of fc_fcp_cmd_send() and fc_fcp_srr() as well.
Numerous calls to error handling routines (fc_disc_error(),
fc_lport_error(), fc_rport_error_retry() ) were passing in a frame pointer that
had already been freed in the case of an error. I have changed the call
sites to pass in a NULL pointer, but there may be more appropriate error
codes to use.
Question: Why do these error routines take a frame pointer anyway? I
understand passing in a pointer encoded error to the response handlers, but
the error routines take no action on a valid pointer and should never be
called that way.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Calls ndo_fcoe_enabled() of the associated netdev upon creating the FCoE
instance to make sure LLD has all necessary resources allocated and setup
properly before passing FCoE traffic. Similarly, calls ndo_fcoe_disable()
upon destroying the FCoE instance on the associated netdev to allow the LLD
to release all allocated resources for FCoE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
In case of sequence offload, in fc_fcp_send_data(), the skb_fill_page_info()
called may end up adding more frags to the skb_shinfo(fp_skb(fp))->frags[],
exceeding SKB_MAX_FRAGS, this eventually corrupts the memory. I am adding the
FR_FRAME_SG_LEN back, but as SKB_MAX_FRAGS -1, leaving 1 for our fcoe_eof_crc
page. And send will be broken into multiple large sends if the frame already
contains more frags than skb handle.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add a define of FCOE_MTU as 2158 bytes and use FCOE_MTU when the LLD is found
to support NETIF_F_FCOE_MTU. The lport->mfs is then calculated out of the
2158 FCOE_MTU. Otherwise, we stick with the netdev->mtu, i.e., LAN MTU. Also,
change the notification on NETDEV_CHANGEMTU event to bypass changing mfs when
LAN MTU is changed if NETIF_F_FCOE_MTU is supported.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When doing echo ethX > /sys..../destroy I am getting
errors when the tear down succeeds. It looks like the
reason for this is because the rc var is not getting set
when the destruction works. This just sets it to zero.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Reported-by: Alex Lyakas <alexl@mellanox.co.il>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Adds missing exch release when RRQ is accepted by calling
fc_seq_ls_acc. Adds common exch release for fc_exch_els_rrq
by use of out label.
Reported-by: Alex Lyakas <alexl@mellanox.co.il>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Initializing these libfc globals per lport could mess up exch
allocation/free for existing lport.
So this patch moves their initialization to fc_setup_exch_mgr
so that these globals gets initialized only once for libfc.
Reported-by: Alex Lyakas <alexl@mellanox.co.il>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
It's possible and harmless to get FLOGI timeouts
while in RESET state. Don't do a WARN_ON in that case.
Also, split out the other WARN_ONs in fc_lport_timeout, so
we can tell which one is hit by its line number.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix minor errors.
A debug message said an RLIR was received instead of ECHO.
"Expected" was misspelled in several places.
Fix a type cast from u32 to __be32.
Rob, Some of these may have been also taken care of in your
other doc cleanup patch. Feel free to fold them in.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This bug is exposed when there is a link flap in LLD. Particularly, when it
happens right after a SCSI write command is sent out, no FCP_DATA is sent,
causing fsp->status_code to be set as FC_DATA_UNDRUN in fc_fcp_complete_locked
even no SCSI status is received. Consequently, fc_io_compl treats this as DID_OK.
This results in SCSI returning successful to the initial I/O request even
there is no DATA actually sent. Particularly, if you run an I/O tool w/ data
verification on, the read back for verification is gonna fail.
This is fixed here by checking when FC_DATA_UNDRUN happens, SCSI status is
received w/ FC_SRB_RCV_STATUS set in fsp->state.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This argument isn't used, let's not pass it into the routine.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
These are a few functions that were not used by other
modules. They did not need to be exported so this patch
removes the EXPORT_SYMBOLS call for each.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove the redundant checking of netdev->netdev_ops as it will never be NULL.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
xid 0 was used as an indication of invalid xid before but now xid 0
can be used as a valid exchange i. This patch fixes the ddp completion
in fcp layer, i.e., in fc_fcp.c:fc_fcp_ddp_done() function, to make sure it
does not use xid 0 for indication of an invalid xid, instead, it now
uses use FC_XID_UNKNOWN for such indication.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
A received Fibre Channel ELS PRLI request contains a bit that
indicates whether the remote port supports certain retry processing
sequences. The test for this bit was somehow coded to use multiply
instead of AND!
This case would apply only for target mode operation, and it is
unlikely to be noticed as an initiator.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Bump driver version to 1.0.7.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Adds support for FC passthru via BSG.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When issuing a Cancel to the virtual fibre channel adapter,
the interface specifies a flags field for the client to indicate
what kind of error recovery is being performed. Fix up these
flags for terminate_rport_io to indicate an abort task set
rather than a target reset.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove a parameter to ibmvfc_init_host which is always set to
zero by all callers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Need to grab the host lock around the call to ibmvfc_link_down.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When processing the response to either a LUN reset,
target reset, or an abort task set, the ibmvfc driver needs to
treat as success receiving a response with a non-zero
status in the response IU along with a general transport
error with the FCP response code being zero. The VIOS
currently guarantees this cannot happen, but a future version
of VIOS may allow this to be returned, so ensure we handle
this response combination correctly for TMFs, as we already
do for SCSI commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This version fixes 64-bit modulo on 32-bit as well as inadvertent map
updates when TP was disabled.
Implement support for thin provisioning in scsi_debug. No actual memory
de-allocation is taking place. The intent is to emulate a thinly
provisioned storage device, not to be one.
There are four new module options:
- unmap_granularity specifies the granularity at which to track mapped
blocks (specified in number of logical blocks). 2048 (1 MB) is a
realistic value for disk arrays although some may have a finer
granularity.
- unmap_alignment specifies the first LBA which is naturally aligned on
an unmap_granularity boundary.
- unmap_max_desc specifies the maximum number of ranges that can be
unmapped using one UNMAP command. If this is 0, only WRITE SAME is
supported and UNMAP will cause a check condition.
- unmap_max_blocks specifies the maximum number of blocks that can be
unmapped using a single UNMAP command. Default is 0xffffffff.
These parameters are reported in the new and extended block limits VPD.
If unmap_granularity is specified the device is tagged as thin
provisioning capable in READ CAPACITY(16). A bitmap is allocated to
track whether blocks are mapped or not. A WRITE request will cause a
block to be mapped. So will WRITE SAME unless the UNMAP bit is set.
Blocks can be unmapped using either WRITE SAME or UNMAP. No accounting
is done to track partial blocks. This means that only whole blocks will
be marked free. This is how the array people tell me their firmwares
work.
GET LBA STATUS is also supported. This command reports whether a block
is mapped or not, and how long the adjoining mapped/unmapped extent is.
The block allocation bitmap can also be viewed from user space via:
/sys/bus/pseudo/drivers/scsi_debug/map
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add definitions for UNMAP, WRITE SAME{16,32} and GET LBA STATUS
commands.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Correct issues where the lower scsi-status would be improperly
cleared, instead, allow the midlayer to process the status after
the proper residual-count checks are performed. Finally,
validate firmware status flags prior to assigning values from the
FCP_RSP frame.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Michael Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
link disruptions.
Original code would not register FC4 nor FDMI information after a
logical tear-down of an VFC link. Code now triggers registration
date during processing of a 'Report ID Acquisition IOCB', which
is submitted after a FLOGI or FDISC completes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Original code discarded response-info field information and
assumed the command completed successfully without verifying the
target's status within the FCP_RSP packet.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
parameters to 4K.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
In some case, the MPI and PHY versions when retrieved after the
Execute-FW mailbox-command are incorrect (255.255.255.255).
Instead, query the information after the check for firmware ready
is done in the abort ISP path.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The mailbox register values may assist in debugging efforts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch fixes checkpatch errors/warnings in bfad files.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
I was doing some large lun count testing with 2.6.31 and hit
a BUG_ON() in fc_timeout_deleted_rport(), and it seems like it
should have been just a matter of time before someone did.
It seems invalid to set port_state under lock, then expect it to
remain set after releasing the lock. Another thread called
fc_remote_port_add() when the lock was released, changing the
port_state.
This patch removes the BUG_ON and moves the test of the
port_state to inside the host_lock. It's been running for
several weeks now with no ill effect.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When the Integrity check is done in scsi_io_completion it will
set error to -EILSEQ. However, at this point error is no longer
used, and blk_end_request_err has -EIO hardcoded.
It looks like there was just porting mistake with this patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=3e695f89c5debb735e4ff051e9e58d8fb4e95110
and we meant to send error upwards, so this patch changes the hard
coded EIO to the error variable.
I have only boot tested this patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Update version to 4.6.0000.4.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support for reset request from firmware for controllers
of st_shasta and st_yel type. Code adjustments necessary
for this change are also included.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
