| Age | Commit message (Collapse) | Author |
|---|
|
It's a bug, but it happens to work, as BTRFS_COMPRESS_LZO == 2, which
has only one bit set.
Signed-off-by: Li Zefan <lizefan@huawei.com>
|
|
If a file has 3 small extents:
| ext1 | ext2 | ext3 |
Running "btrfs fi defrag" will only defrag the last two extents, if those
extent mappings hasn't been read into memory from disk.
This bug was introduced by commit 17ce6ef8d731af5edac8c39e806db4c7e1f6956f
("Btrfs: add a check to decide if we should defrag the range")
The cause is, that commit looked into previous and next extents using
lookup_extent_mapping() only.
While at it, remove the code that checks the previous extent, since
it's sufficient to check the next extent.
Signed-off-by: Li Zefan <lizefan@huawei.com>
|
|
I removed this in an earlier commit and I was wrong. Because compression
can return from filemap_fdatawrite() without having actually set any of it's
pages as writeback() it can make filemap_fdatawait() do essentially nothing,
and then we won't find any ordered extents because they may not have been
created yet. So not only does this make fsync() completely useless, but it
will also screw up if you truncate on a non-page aligned offset since we
zero out the end and then wait on ordered extents and then call drop caches.
We can drop the cache before the io completes and then we try to unpin the
extent we just wrote we won't find it and everything goes sideways. So fix
this by putting it back and put a giant comment there to keep me from trying
to remove it in the future. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
A user reported lots of problems using compression on the new code and it
turns out part of the problem was that igrab() was failing when we added a
new ordered extent. This is because when writing out an inode under
compression we immediately return without actually doing anything to the
pages, and then in another thread at some point down the line actually do
the ordered dance. The problem is between the point that we start writeback
and we actually add the ordered extent we could be trying to reclaim the
inode, which makes igrab() return NULL. So we need to do an igrab() when we
create the async extent and then drop it when we are done with it. This
makes sure we stay pinned in memory until the ordered extent can get a
reference on it and we are good to go. With this patch we no longer panic
in btrfs_finish_ordered_io(). Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
Because btrfs can remove the device that was mounted we need to have a
->show_devname so that in this case we can print out some other device in
the file system to /proc/mount. So if there are multiple devices in a btrfs
file system we will just print the device with the lowest devid that we can
find. This will make everything consistent and deal with device removal
properly. The drawback is if you mount with a device that is higher than
the lowest devicd it won't show up as the mounted device in /proc/mounts,
but this is a small price to pay. This was inspired by Miao Xie's patch.
Thanks,
Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
Al pointed out that we can just toss out the old name on a device and add a
new one arbitrarily, so anybody who uses device->name in printk could
possibly use free'd memory. Instead of adding locking around all of this he
suggested doing it with RCU, so I've introduced a struct rcu_string that
does just that and have gone through and protected all accesses to
device->name that aren't under the uuid_mutex with rcu_read_lock(). This
protects us and I will use it for dealing with removing the device that we
used to mount the file system in a later patch. Thanks,
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
I was getting hung on umount when a transaction was aborted because a range
of one of the free space inodes was still locked. This is because the nocow
stuff doesn't unlock anything on error. This fixed the problem and I
verified that is what was happening. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
So we're forcing the eb's to have their ref count set to 1 so invalidatepage
works but this breaks lots of things, for example root nodes, and is just
plain wrong, we don't need to just evict all of this stuff. Also drop the
invalidatepage altogether and add a page_cache_release(). With this patch
we no longer hang when trying to access the root nodes after an aborted
transaction and we no longer leak memory. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
If a transaction commit fails we don't abort it so we don't set an error on
the file system. This patch fixes that by actually calling the abort stuff
and then adding a check for a fs error in the transaction start stuff to
make sure it is caught properly. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
I was getting lots of hung tasks and a NULL pointer dereference because we
are not cleaning up the transaction properly when it aborts. First we need
to reset the running_transaction to NULL so we don't get a bad dereference
for any start_transaction callers after this. Also we cannot rely on
waitqueue_active() since it's just a list_empty(), so just call wake_up()
directly since that will do the barrier for us and such. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
The transaction abort stuff was throwing warnings from the list debugging
code because we do a list_del_init outside of the delayed_refs spin lock.
The delayed refs locking makes baby Jesus cry so it's not hard to get wrong,
but we need to take the ref head mutex to make sure it's not being processed
currently, and so if it is we need to drop the spin lock and then take and
drop the mutex and do the search again. If we can take the mutex then we
can safely remove the head from the list and carry on. Now when the
transaction aborts I don't get the list debugging warnings. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
While doing my enospc work I got a transaction abortion that resulted in a
panic when we tried to unlock_page() an already unlocked page. This is
because we aren't calling extent_clear_unlock_delalloc with the locked page
so it was unlocking all the pages in the range. This is wrong since
__extent_writepage expects to have the page locked still unless we return
*page_started as 1. This should keep us from panicing. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
TEAC's UD-H01 (and probably other devices) have a gap in the interface
number allocation of their descriptors:
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 220
bNumInterfaces 3
[...]
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
[...]
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 2
bInterfaceCount 2
bFunctionClass 1 Audio
bFunctionSubClass 0
bFunctionProtocol 32
iFunction 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
[...]
Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.
The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.
In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.
Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: bEN <ml_all@circa.be>
Reported-by: Ivan Perrone <ivanperrone@hotmail.com>
Tested-by: ivan perrone <ivanperrone@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the platform_data is not set, pdata will be uninitialized value.
Since the driver has the following code, if the condition is true when
the pdata is uninitialized value, the driver may jump to the illegal
phy_init().
if (pdata && pdata->phy_init)
pdata->phy_init();
This patch also fixes the following warning:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-sh.c: In function ‘ehci_hcd_sh_probe’:
drivers/usb/host/ehci-sh.c:104: warning: ‘pdata’ may be used uninitialized in this function
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently CDC-ACM devices stay throttled when their TTY is closed while
throttled, stalling further communication attempts after the next open.
Unthrottling during open/activate got lost starting with kernel
3.0.0 and this patch reintroduces it.
Signed-off-by: Otto Meta <otto.patches@sister-shadow.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the frontend and the backend reside on the same domain, even if we
add pages to the m2p_override, these pages will never be returned by
mfn_to_pfn because the check "get_phys_to_machine(pfn) != mfn" will
always fail, so the pfn of the frontend will be returned instead
(resulting in a deadlock because the frontend pages are already locked).
INFO: task qemu-system-i38:1085 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
qemu-system-i38 D ffff8800cfc137c0 0 1085 1 0x00000000
ffff8800c47ed898 0000000000000282 ffff8800be4596b0 00000000000137c0
ffff8800c47edfd8 ffff8800c47ec010 00000000000137c0 00000000000137c0
ffff8800c47edfd8 00000000000137c0 ffffffff82213020 ffff8800be4596b0
Call Trace:
[<ffffffff81101ee0>] ? __lock_page+0x70/0x70
[<ffffffff81a0fdd9>] schedule+0x29/0x70
[<ffffffff81a0fe80>] io_schedule+0x60/0x80
[<ffffffff81101eee>] sleep_on_page+0xe/0x20
[<ffffffff81a0e1ca>] __wait_on_bit_lock+0x5a/0xc0
[<ffffffff81101ed7>] __lock_page+0x67/0x70
[<ffffffff8106f750>] ? autoremove_wake_function+0x40/0x40
[<ffffffff811867e6>] ? bio_add_page+0x36/0x40
[<ffffffff8110b692>] set_page_dirty_lock+0x52/0x60
[<ffffffff81186021>] bio_set_pages_dirty+0x51/0x70
[<ffffffff8118c6b4>] do_blockdev_direct_IO+0xb24/0xeb0
[<ffffffff811e71a0>] ? ext3_get_blocks_handle+0xe00/0xe00
[<ffffffff8118ca95>] __blockdev_direct_IO+0x55/0x60
[<ffffffff811e71a0>] ? ext3_get_blocks_handle+0xe00/0xe00
[<ffffffff811e91c8>] ext3_direct_IO+0xf8/0x390
[<ffffffff811e71a0>] ? ext3_get_blocks_handle+0xe00/0xe00
[<ffffffff81004b60>] ? xen_mc_flush+0xb0/0x1b0
[<ffffffff81104027>] generic_file_aio_read+0x737/0x780
[<ffffffff813bedeb>] ? gnttab_map_refs+0x15b/0x1e0
[<ffffffff811038f0>] ? find_get_pages+0x150/0x150
[<ffffffff8119736c>] aio_rw_vect_retry+0x7c/0x1d0
[<ffffffff811972f0>] ? lookup_ioctx+0x90/0x90
[<ffffffff81198856>] aio_run_iocb+0x66/0x1a0
[<ffffffff811998b8>] do_io_submit+0x708/0xb90
[<ffffffff81199d50>] sys_io_submit+0x10/0x20
[<ffffffff81a18d69>] system_call_fastpath+0x16/0x1b
The explanation is in the comment within the code:
We need to do this because the pages shared by the frontend
(xen-blkfront) can be already locked (lock_page, called by
do_read_cache_page); when the userspace backend tries to use them
with direct_IO, mfn_to_pfn returns the pfn of the frontend, so
do_blockdev_direct_IO is going to try to lock the same pages
again resulting in a deadlock.
A simplified call graph looks like this:
pygrub QEMU
-----------------------------------------------
do_read_cache_page io_submit
| |
lock_page ext3_direct_IO
|
bio_add_page
|
lock_page
Internally the xen-blkback uses m2p_add_override to swizzle (temporarily)
a 'struct page' to have a different MFN (so that it can point to another
guest). It also can easily find out whether another pfn corresponding
to the mfn exists in the m2p, and can set the FOREIGN bit
in the p2m, making sure that mfn_to_pfn returns the pfn of the backend.
This allows the backend to perform direct_IO on these pages, but as a
side effect prevents the frontend from using get_user_pages_fast on
them while they are being shared with the backend.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Most frequent symptom was a BUG triggering in expire_client, with the
server locking up shortly thereafter.
Introduced by 508dc6e110c6dbdc0bbe84298ccfe22de7538486 "nfsd41:
free_session/free_client must be called under the client_lock".
Cc: stable@kernel.org
Cc: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
In case of destroying mount namespace on child reaper exit, nsproxy is zeroed
to the point already. So, dereferencing of it is invalid.
This patch hard-code "init_net" for all network namespace references for NFS
callback services. This will be fixed with proper NFS callback
containerization.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
When adding to the tree modification log, we grab two locks at different
stages. We must not drop the outer lock until we're done with section
protected by the inner lock. This moves the unlock call for the outer lock
to the appropriate position.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
To make sense of the tree mod log, the backref walker not only needs
btrfs_search_old_slot, but it also called btrfs_next_leaf, which in turn was
calling btrfs_search_slot. This obviously didn't give the correct result.
This commit adds btrfs_next_old_leaf, a drop-in replacement for
btrfs_next_leaf with a time_seq parameter. If it is zero, it behaves exactly
like btrfs_next_leaf. If it is non-zero, it will use btrfs_search_old_slot
with this time_seq parameter.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
In __tree_mod_log_oldest_root() we must return the found operation even if
it's not a ROOT_REPLACE operation. Otherwise, the caller assumes that there
are no operations to be rewinded and returns immediately.
The code in the caller is modified to improve readability.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
get_old_root could race with root node updates because we weren't locking
the node early enough. Use btrfs_read_lock_root_node to grab the root locked
in the very beginning and release the lock as soon as possible (just like
btrfs_search_slot does).
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
When resolving indirect refs, we used to call btrfs_next_leaf in case we
didn't find an exact match. While we should find exact matches most of the
time, in case we don't, we must continue searching. Treating those matches
differently depending on the level we're searching doesn't make sense.
Even worse, we might end up searching for a key larger than the largest, in
which case there is no next_leaf and subsequent jobs would fail. This commit
drops the bogous lines.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
Pull kvm fix from Marcelo Tosatti:
"Fix a spurious warning on CPU offline path"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: kvmclock: remove check_and_clear_guest_paused warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
* tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister
pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails
pinctrl: pinctrl-imx: fix incorrect debug message of maps
pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node
pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
pinctrl: nomadik: fix up typo
pinctrl: nomadik: add clk_prepare() call
pinctrl: fix a minor harmless typo
pinctrl: sirf: mark of_device_id match table as __devinitconst
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
|
|
Pull networking fixes from David S. Miller:
This has the fix for the wireless issues I ran into the other week as
well as:
1) Fix CAN c_can driver transmit handling resulting in BUG check
triggers, from AnilKumar Ch.
2) Fix packet drop monitor sleeping in atomic context, from Eric
Dumazet.
3) Fix mv643xx_eth driver build regression, from Andrew Lunn.
4) Inetpeer freeing needs an RCU grace period in order to avoid races
during tree invalidation. From Eric Dumazet.
5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
Schillstrom.
6) Add proper module refcounting to l2tp_eth to avoid crash on module
unload, from Eric Dumazet.
7) Fix truncation of neighbour entry dumps due to logic errors in
neigh_dump_info() and friends, from Eric Dumazet.
8) The conversion of fib6_age() to dst_neigh_lookup() accidently
reversed the logic of a flags test, fix from Thomas Graf.
9) Fix checksum configuration in newer sky2 chips, from Stephen
Hemminger.
10) Revert BQL support in NIU driver, doesn't work.
11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
From Eric Dumazet.
12) be2net driver references an SKB after it's potentially been freed,
also from Eric Dumazet.
13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet.
14) lpc_eth has several bugs in it's transmit engine leading to packet
leaks and improper queue wakes, from Eric Dumazet.
15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.
16) Add tilegx network driver.
17) Bonding queue mapping for a packet can get corrupted, fix from Eric
Dumazet.
18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
in the payload in certain situations. From Eric Dumazet.
19) bnx2x driver interprets chip RX checksum offload incorrectly in
encapsulation situations. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
bnx2x: fix checksum validation
netpoll: fix netpoll_send_udp() bugs
bonding: Fix corrupted queue_mapping
bonding:record primary when modify it via sysfs
tilegx network driver: initial support
tg3: Apply short DMA frag workaround to 5906
net: stmmac: Fix clock en-/disable calls
lpc_eth: fix tx completion
lpc_eth: add missing ndo_change_mtu()
dummy: fix rcu_sched self-detected stalls
net: Reorder initialization in ip_route_output to fix gcc warning
virtio-net: fix a race on 32bit arches
r8169: avoid NAPI scheduling delay.
net: Make linux/tcp.h C++ friendly (trivial)
netdev: fix drivers/net/phy/ kernel-doc warnings
net/core: fix kernel-doc warnings
be2net: fix a race in be_xmit()
l2tp: fix a race in l2tp_ip_sendmsg()
mac80211: add back channel change flag
NFC: Fix possible NULL ptr deref when getting the name of a socket
...
|
|
Commit 0a2b9a6ea93 ("X86: integrate CMA with DMA-mapping subsystem")
broke memory allocation with dma_mask. This patch fixes possible kernel
ops caused by lack of resetting page variable when jumping to 'again' label.
Reported-by: Konrad Rzeszutek Wilk <konrad@darnok.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
|
|
A bunch of bugzillas have complained how noisy the nmi_watchdog
is during boot-up especially with its expected failure cases
(like virt and bios resource contention).
This is my attempt to quiet them down and keep it less confusing
for the end user. What I did is print the message for cpu0 and
save it for future comparisons. If future cpus have an
identical message as cpu0, then don't print the redundant info.
However, if a future cpu has a different message, happily print
that loudly.
Before the change, you would see something like:
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1
NMI watchdog enabled, takes one hw-pmu counter.
#2
NMI watchdog enabled, takes one hw-pmu counter.
#3 Ok.
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 4 CPUs
Total of 4 processors activated (22607.24 BogoMIPS).
After the change, it is simplified to:
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
Booting Node 0, Processors #1 #2 #3 Ok.
Brought up 4 CPUs
V2: little changes based on Joe Perches' feedback
V3: printk cleanup based on Ingo's feedback; checkpatch fix
V4: keep printk as one long line
V5: Ingo fix ups
Reported-and-tested-by: Nathan Zimmer <nzimmer@sgi.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: nzimmer@sgi.com
Cc: joe@perches.com
Link: http://lkml.kernel.org/r/1339594548-17227-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Its observed with some PHY, the 60Mhz clock gets
cut too soon for OMAP EHCI, leaving OMAP-EHCI in a bad state.
So on starting port suspend, make sure the 60Mhz clock to EHCI
is kept alive using an internal clock, so that EHCi can cleanly
transition its hw state machine on a port suspend.
Its not proven if this is the issue hit on USB3333,
but the symptoms look very similar.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Volodymyr Mieshkov <x0182794@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ohci_finish_controller_resume() is intended to be used in platform specific
drivers ohci-*.c, included from ohci-hcd.c. Some of them don't actually use
ohci_finish_controller_resume(), so mark it as __maybe_unused.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The use of kfree(serial) in error cases of usb_serial_probe
was invalid - usb_serial structure allocated in create_serial()
gets reference of usb_device that needs to be put, so we need
to use usb_serial_put() instead of simple kfree().
Signed-off-by: Jan Safrata <jan.nikitenko@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes the following warning:
In file included from drivers/usb/host/ehci-hcd.c:1246:0:
drivers/usb/host/ehci-xilinx-of.c:293:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/usb/host/ehci-xilinx-of.c:293:2: warning: (near initialization for 'ehci_hcd_xilinx_of_driver.shutdown') [enabled by default]
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit aaa0ef289afe9186f81e2340114ea413eef0492a "PS3 EHCI QH
read work-around", Terratec Grabby (em28xx) stopped working with AMD
Geode LX 800 (USB controller AMD CS5536). Since this is a PS3 only
fix, the following patch adds a conditional block around it.
Signed-off-by: Ricardo Martins <rasm@fe.up.pt>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xhci: Bug fixes for 3.5
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
|
|
When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.
xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.
Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.
This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation"
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org
|
|
This patch fixes a few issues introduced in the recent fix
[f8a9e72d: USB: fix resource leak in xhci power loss path]
- The endpoints listed in bw table are just links and each entry is an
array member of dev->eps[]. But the commit above adds a kfree() call
to these instances, and thus it results in memory corruption.
- It clears only the first entry of rh_bw[], but there can be multiple
ports.
- It'd be safer to clear the list_head of ep as well, not only
removing from the list, as it's checked in
xhci_discover_or_reset_device().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
|
|
xhci_free_tt_info() may access the invalid memory when it removes the
last entry but the list is not empty. Then tt_next reaches to the
list head but it still tries to check the tt_info of that entry.
This patch fixes the bug and cleans up the messy code by rewriting
with a simple list_for_each_entry_safe().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
|
|
This patch fixes an issue discovered by Dan Carpenter:
The patch 3b3db026414b: "xhci: Add infrastructure for host-specific
LPM policies." from May 9, 2012, leads to the following warning:
drivers/usb/host/xhci.c:3909 xhci_get_timeout_no_hub_lpm()
warn: signedness bug returning '-22'
3906 default:
3907 dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
3908 __func__);
3909 return -EINVAL;
^^^^^^^^^^^^^^
This should be a u16 like USB3_LPM_DISABLED or something.
3910 }
3911
3912 if (sel <= max_sel_pel && pel <= max_sel_pel)
3913 return USB3_LPM_DEVICE_INITIATED;
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
|
|
We check "u1_params" instead of checking "u2_params".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
This device gives a bogus answer to get_capacity(16):
[ 8628.278614] scsi 8:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[ 8628.279452] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 8628.280338] sd 8:0:0:0: [sdd] 35747322042253313 512-byte logical blocks: (18.3 EB/15.8 EiB)
So set the quirk flag to avoid using get_capacity(16) with it:
[11731.386014] usb-storage 2-1.6:1.0: Quirks match for vid 090c pid 1000: 80000
[11731.386075] scsi9 : usb-storage 2-1.6:1.0
[11731.386172] usbcore: registered new interface driver usb-storage
[11731.386175] USB Mass Storage support registered.
[11732.387394] scsi 9:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[11732.388462] sd 9:0:0:0: Attached scsi generic sg3 type 0
[11732.389432] sd 9:0:0:0: [sdc] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB)
Which makes the capacity look a lot more sane :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Simon Raffeiner <sturmflut@lieberbiber.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.
Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.
Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.
Patch based on findings and analysis from Robert Evans
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bogdan Hamciuc diagnosed and fixed following bug in netpoll_send_udp() :
"skb->len += len;" instead of "skb_put(skb, len);"
Meaning that _if_ a network driver needs to call skb_realloc_headroom(),
only packet headers would be copied, leaving garbage in the payload.
However the skb_realloc_headroom() must be avoided as much as possible
since it requires memory and netpoll tries hard to work even if memory
is exhausted (using a pool of preallocated skbs)
It appears netpoll_send_udp() reserved 16 bytes for the ethernet header,
which happens to work for typicall drivers but not all.
Right thing is to use LL_RESERVED_SPACE(dev)
(And also add dev->needed_tailroom of tailroom)
This patch combines both fixes.
Many thanks to Bogdan for raising this issue.
Reported-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The usb-serial-generic driver uses different device IDs for its USB
matching and its serial matching. This can lead to problems: The
driver can end up getting bound to a USB interface without being
allowed to bind to the corresponding serial port.
This patch (as1557) fixes the problem by using the same device ID
table (the one that can be altered by the "vendor=" and "product="
module parameters) for both purposes. The unused table is removed.
Now the driver will bind only to the intended devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need to make sure that the USB serial driver we find
matches the USB driver whose probe we are currently
executing. Otherwise we will end up with USB serial
devices bound to the correct serial driver but wrong
USB driver.
An example of such cross-probing, where the usbserial_generic
USB driver has found the sierra serial driver:
May 29 18:26:15 nemi kernel: [ 4442.559246] usbserial_generic 4-4:1.0: Sierra USB modem converter detected
May 29 18:26:20 nemi kernel: [ 4447.556747] usbserial_generic 4-4:1.2: Sierra USB modem converter detected
May 29 18:26:25 nemi kernel: [ 4452.557288] usbserial_generic 4-4:1.3: Sierra USB modem converter detected
sysfs view of the same problem:
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/sierra
-rw-r--r-- 1 root root 4096 May 29 18:23 new_id
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0/ttyUSB0
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB1 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2/ttyUSB1
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3/ttyUSB2
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/usbserial_generic/
total 0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.3 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/generic/
total 0
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
-rw-r--r-- 1 root root 4096 May 29 18:33 new_id
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
So we end up with a mismatch between the USB driver and the
USB serial driver. The reason for the above is simple: The
USB driver probe will succeed if *any* registered serial
driver matches, and will use that serial driver for all
serial driver functions.
This makes ref counting go wrong. We count the USB driver
as used, but not the USB serial driver. This may result
in Oops'es as demonstrated by Johan Hovold <jhovold@gmail.com>:
[11811.646396] drivers/usb/serial/usb-serial.c: get_free_serial 1
[11811.646443] drivers/usb/serial/usb-serial.c: get_free_serial - minor base = 0
[11811.646460] drivers/usb/serial/usb-serial.c: usb_serial_probe - registering ttyUSB0
[11811.646766] usb 6-1: pl2303 converter now attached to ttyUSB0
[11812.264197] USB Serial deregistering driver FTDI USB Serial Device
[11812.264865] usbcore: deregistering interface driver ftdi_sio
[11812.282180] USB Serial deregistering driver pl2303
[11812.283141] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[11812.283272] usbcore: deregistering interface driver pl2303
[11812.301056] USB Serial deregistering driver generic
[11812.301186] usbcore: deregistering interface driver usbserial_generic
[11812.301259] drivers/usb/serial/usb-serial.c: usb_serial_disconnect
[11812.301823] BUG: unable to handle kernel paging request at f8e7438c
[11812.301845] IP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.301871] *pde = 357ef067 *pte = 00000000
[11812.301957] Oops: 0000 [#1] PREEMPT SMP
[11812.301983] Modules linked in: usbserial(-) [last unloaded: pl2303]
[11812.302008]
[11812.302019] Pid: 1323, comm: modprobe Tainted: G W 3.4.0-rc7+ #101 Dell Inc. Vostro 1520/0T816J
[11812.302115] EIP: 0060:[<f8e38445>] EFLAGS: 00010246 CPU: 1
[11812.302130] EIP is at usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.302141] EAX: f508a180 EBX: f508a180 ECX: 00000000 EDX: f8e74300
[11812.302151] ESI: f5050800 EDI: 00000001 EBP: f5141e78 ESP: f5141e58
[11812.302160] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[11812.302170] CR0: 8005003b CR2: f8e7438c CR3: 34848000 CR4: 000007d0
[11812.302180] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[11812.302189] DR6: ffff0ff0 DR7: 00000400
[11812.302199] Process modprobe (pid: 1323, ti=f5140000 task=f61e2bc0 task.ti=f5140000)
[11812.302209] Stack:
[11812.302216] f8e3be0f f8e3b29c f8e3ae00 00000000 f513641c f5136400 f513641c f507a540
[11812.302325] f5141e98 c133d2c1 00000000 00000000 f509c400 f513641c f507a590 f5136450
[11812.302372] f5141ea8 c12f0344 f513641c f507a590 f5141ebc c12f0c67 00000000 f507a590
[11812.302419] Call Trace:
[11812.302439] [<c133d2c1>] usb_unbind_interface+0x51/0x190
[11812.302456] [<c12f0344>] __device_release_driver+0x64/0xb0
[11812.302469] [<c12f0c67>] driver_detach+0x97/0xa0
[11812.302483] [<c12f001c>] bus_remove_driver+0x6c/0xe0
[11812.302500] [<c145938d>] ? __mutex_unlock_slowpath+0xcd/0x140
[11812.302514] [<c12f0ff9>] driver_unregister+0x49/0x80
[11812.302528] [<c1457df6>] ? printk+0x1d/0x1f
[11812.302540] [<c133c50d>] usb_deregister+0x5d/0xb0
[11812.302557] [<f8e37c55>] ? usb_serial_deregister+0x45/0x50 [usbserial]
[11812.302575] [<f8e37c8d>] usb_serial_deregister_drivers+0x2d/0x40 [usbserial]
[11812.302593] [<f8e3a6e2>] usb_serial_generic_deregister+0x12/0x20 [usbserial]
[11812.302611] [<f8e3acf0>] usb_serial_exit+0x8/0x32 [usbserial]
[11812.302716] [<c1080b48>] sys_delete_module+0x158/0x260
[11812.302730] [<c110594e>] ? mntput+0x1e/0x30
[11812.302746] [<c145c3c3>] ? sysenter_exit+0xf/0x18
[11812.302746] [<c107777c>] ? trace_hardirqs_on_caller+0xec/0x170
[11812.302746] [<c145c390>] sysenter_do_call+0x12/0x36
[11812.302746] Code: 24 02 00 00 e8 dd f3 20 c8 f6 86 74 02 00 00 02 74 b4 8d 86 4c 02 00 00 47 e8 78 55 4b c8 0f b6 43 0e 39 f8 7f a9 8b 53 04 89 d8 <ff> 92 8c 00 00 00 89 d8 e8 0e ff ff ff 8b 45 f0 c7 44 24 04 2f
[11812.302746] EIP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial] SS:ESP 0068:f5141e58
[11812.302746] CR2: 00000000f8e7438c
Fix by only evaluating serial drivers pointing back to the
USB driver we are currently probing. This still allows two
or more drivers to match the same device, running their
serial driver probes to sort out which one to use.
Cc: stable@vger.kernel.org # 3.0, 3.2, 3.3, 3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Kill off additional asm-generic wrappers.
sh: Setup CROSS_COMPILE at the top
sh: Fix up link time defsym warnings.
sh: use the new generic strnlen_user() function
sh: switch to generic strncpy_from_user().
sh: Kill off last dead UBC header
serial: sh-sci: Make probe fail for ports that exceed the maximum count
serial: sh-sci: Fix probe error paths
clocksource: sh_tmu: Use clockevents_config_and_register().
clocksource: sh_tmu: Convert timer lock to raw spinlock.
clocksource: sh_mtu2: Convert timer lock to raw spinlock.
clocksource: sh_cmt: Convert timer lock to raw spinlock.
bug.h: need linux/kernel.h for TAINT_WARN.
sh: convert to kbuild asm-generic support.
sh64: Fix up fallout from generic init_task conversion.
sh: arch/sh/kernel/process.c needs asm/fpu.h for unlazy_fpu().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull led fixes from Bryan Wu.
* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
leds: fixed a coding style issue.
leds: don't disable blinking when writing the same value to delay_on or delay_off
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
This makes m68k use the generic library functions for the user-space
strn[cpy|len] functions.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Use generic strncpy_from_user(), strlen_user(), and strnlen_user()
|
|
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Divider value can be zero and it makes division by zero
from debug message in s3c_fb_calc_pixclk; therefore, it
should be fixed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
