summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-02-16MIPS: Netlogic: No hazards needed for XLR/XLSJayachandran C
TLB and COP0 hazards are handled in hardware for Netlogic XLR/XLS SoCs. Update hazards.h to pick more optimal set of definitions when compiling for XLR/XLS. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4788/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: PCI: Prevent hang on XLP reg readJayachandran C
Reading PCI extended register at 0x255 on a bridge will hang if there is no device connected on the link. Make PCI read routine skip this register. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4789/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: Netlogic: Use PIC timer as a clocksourceJayachandran C
The XLR/XLS/XLP PIC has a 8 countdown timers which run at the PIC frequencey. One of these can be used as a clocksource to provide timestamps that is common across cores. This can be used in place of the count/compare clocksource which is per-CPU. On XLR/XLS PIC registers are 32-bit, so we just use the lower 32-bits of the PIC counter. On XLP, the whole 64-bit can be used. Provide common macros and functions for PIC timer registers on XLR/XLS and XLP, and use them to register a PIC clocksource. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4786/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: Netlogic: Split XLP L1 i-cache among threadsJayachandran C
Since we now use r4k cache code for Netlogic XLP, it is better to split L1 icache among the active threads, so that threads won't step on each other while flushing icache. The L1 dcache is already split among the threads in the core. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4787/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: PCI: Byteswap not needed in little-endian modeJayachandran C
Rename function xlp_enable_pci_bswap() to xlp_config_pci_bswap(), which is a better description for its functionality. When compiled in big-endian mode, xlp_config_pci_bswap() will configure the PCIe links to byteswap. In little-endian mode, no swap configuration is needed for the PCIe controller, and the function is empty. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4802/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: Netlogic: Optimize EIMR/EIRR accesses in 32-bitJayachandran C
Provide functions ack_c0_eirr(), set_c0_eimr(), clear_c0_eimr() and read_c0_eirr_and_eimr() that do the EIMR and EIRR operations and update the interrupt handling code to use these functions. Also, use the EIMR register functions to mask interrupts in the irq code. The 64-bit interrupt request and mask registers (EIRR and EIMR) are accessed when the interrupts are off, and the common operations are to set or clear a bit in these registers. Using the 64-bit c0 access functions for these operations is not optimal in 32-bit, because it will disable/restore interrupts and split/join the 64-bit value during each register access. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4790/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: Netlogic: add XLS6xx to FMN configJayachandran C
Add support for XLS6xx CPUs to the Fast Message Network (FMN) configuration. Signed-off-by: Jayachandran C <jchandra@broadcom.com> Patchwork: http://patchwork.linux-mips.org/patch/4785/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-16MIPS: lantiq: rework external irq codeJohn Crispin
This code makes the irqs used by the EIU loadable from the DT. Additionally we add a helper that allows the pinctrl layer to map external irqs to real irq numbers. Signed-off-by: John Crispin <blogic@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/4818/
2013-02-16MIPS: lantiq: improve pci reset gpio handlingJohn Crispin
We need to make sure that the reset gpio is available and also set a sane default state. Signed-off-by: John Crispin <blogic@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/4817/
2013-02-16MIPS: lantiq: add GPHY clock gate bitsJohn Crispin
Explicitly enable the clock gate of the internal GPHYs found on xrx200. Signed-off-by: John Crispin <blogic@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/4816/
2013-02-16MIPS: lantiq: adds static clock for PP32John Crispin
The Lantiq DSL SoCs have an internal networking processor. Add code to read the static clock rate. Signed-off-by: John Crispin <blogic@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/4815/
2013-02-16MIPS: lantiq: trivial typo fixJohn Crispin
"nodes" is written with a single "s" Signed-off-by: John Crispin <blogic@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/4814/
2013-02-16MIPS: show correct cpu name for 24KEcJohn Crispin
Make sure 24KEc is properly identified inside /proc/cpuinfo Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: use fallback sprom var for board_{rev,type}Hauke Mehrtens
An SoC normally do not define path variables for board_rev and board_type and the Broadcom SDK also uses the nvram values without a prefix in such cases. Do the same to fill these sprom attributes from nvram and do not leave them empty, because brcmsmac do not like this. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4679/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: select NO_EXCEPT_FILLHauke Mehrtens
The kernel is loaded to 0x80001000 so there is some space left for the exception handlers and the kernel do not have to reserve some extra space for them. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4747/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: select BOOT_RAWHauke Mehrtens
All the boot loaders I have seen are booting the kernel in raw mode by default. CFE seems to support elf kernel images too, but the default case is raw for the devices I know of. Select this option to make the kernel boot on most of the devices with the default options. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4746/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: trim the nvram values for parsingHauke Mehrtens
Some nvram values on some devices have a newline character at the end of the value, that caused read errors. Trim the string before reading the number. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4745/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: add bcm47xx prefix in front of nvram function namesHauke Mehrtens
The nvram functions are exported and used by some normal drivers. To prevent name clashes with ofter parts of the kernel code add a bcm47xx_ prefix in front of the function names and the header file name. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4744/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: handle different nvram sizesHauke Mehrtens
The old code just worked for nvram with a size of 0x8000 bytes. This patch adds support for reading nvram from partitions of 0xF000 and 0x10000 bytes. There is just 32KB space for the nvram, but most devices do not use the full size and this code reads the first 32KB in that case and prints a warning. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4743/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: rename early_nvram_init to nvram_initHauke Mehrtens
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4742/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: nvram add nand flash supportHauke Mehrtens
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4741/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: return error when init of nvram failedHauke Mehrtens
This makes it possible to handle the case of not being able to read the nvram ram. This could happen when the code searching for the specific flash chip have not run jet. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4740/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: BCM47XX: use common error codes in nvram readsHauke Mehrtens
Instead of using our own error codes use some common codes. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4739/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-15MIPS: bcm47xx: separate functions finding flash window addrRafał Miłecki
Also check if parallel flash is present at all before accessing it and add support for serial flash on BCMA bus. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Patchwork: http://patchwork.linux-mips.org/patch/4738/ Signed-off-by: John Crispin <blogic@openwrt.org>
2013-02-08Linux 3.8-rc7Linus Torvalds
2013-02-08Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "I was going to hold these off until v3.8 was out, and send them with a stable tag, but as everyone else is pushing much bigger fixes which Linus is accepting, let's save people from the hastle of having to patch v3.8 back into working or use a stable kernel. Looking at the diffstat, this really is high value for its size; this is miniscule compared to how the -rc6 to tip diffstat currently looks. So, four patches in this set: - Punit Agrawal reports that the kernel no longer boots on MPCore due to a new assumption made in the GIC code which isn't true of earlier GIC designs. This is the biggest change in this set. - Punit's boot log also revealed a bunch of WARN_ON() dumps caused by the DT-ification of the GIC support without fixing up non-DT Realview - which now sees a greater number of interrupts than it did before. - A fix for the DMA coherent code from Marek which uses the wrong check for atomic allocations; this can result in spinlock lockups or other nasty effects. - A fix from Will, which will affect all Android based platforms if not applied (which use the 2G:2G VM split) - this causes particularly 'make' to misbehave unless this bug is fixed." * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is aligned ARM: DMA mapping: fix bad atomic test ARM: realview: ensure that we have sufficient IRQs available ARM: GIC: fix GIC cpumask initialization
2013-02-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Revert iwlwifi reclaimed packet tracking, it causes problems for a bunch of folks. From Emmanuel Grumbach. 2) Work limiting code in brcmsmac wifi driver can clear tx status without processing the event. From Arend van Spriel. 3) rtlwifi USB driver processes wrong SKB, fix from Larry Finger. 4) l2tp tunnel delete can race with close, fix from Tom Parkin. 5) pktgen_add_device() failures are not checked at all, fix from Cong Wang. 6) Fix unintentional removal of carrier off from tun_detach(), otherwise we confuse userspace, from Michael S. Tsirkin. 7) Don't leak socket reference counts and ubufs in vhost-net driver, from Jason Wang. 8) vmxnet3 driver gets it's initial carrier state wrong, fix from Neil Horman. 9) Protect against USB networking devices which spam the host with 0 length frames, from Bjørn Mork. 10) Prevent neighbour overflows in ipv6 for locally destined routes, from Marcelo Ricardo. This is the best short-term fix for this, a longer term fix has been implemented in net-next. 11) L2TP uses ipv4 datagram routines in it's ipv6 code, whoops. This mistake is largely because the ipv6 functions don't even have some kind of prefix in their names to suggest they are ipv6 specific. From Tom Parkin. 12) Check SYN packet drops properly in tcp_rcv_fastopen_synack(), from Yuchung Cheng. 13) Fix races and TX skb freeing bugs in via-rhine's NAPI support, from Francois Romieu and your's truly. 14) Fix infinite loops and divides by zero in TCP congestion window handling, from Eric Dumazet, Neal Cardwell, and Ilpo Järvinen. 15) AF_PACKET tx ring handling can leak kernel memory to userspace, fix from Phil Sutter. 16) Fix error handling in ipv6 GRE tunnel transmit, from Tommi Rantala. 17) Protect XEN netback driver against hostile frontend putting garbage into the rings, don't leak pages in TX GOP checking, and add proper resource releasing in error path of xen_netbk_get_requests(). From Ian Campbell. 18) SCTP authentication keys should be cleared out and released with kzfree(), from Daniel Borkmann. 19) L2TP is a bit too clever trying to maintain skb->truesize, and ends up corrupting socket memory accounting to the point where packet sending is halted indefinitely. Just remove the adjustments entirely, they aren't really needed. From Eric Dumazet. 20) ATM Iphase driver uses a data type with the same name as the S390 headers, rename to fix the build. From Heiko Carstens. 21) Fix a typo in copying the inner network header offset from one SKB to another, from Pravin B Shelar. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits) net: sctp: sctp_endpoint_free: zero out secret key data net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree atm/iphase: rename fregt_t -> ffreg_t net: usb: fix regression from FLAG_NOARP code l2tp: dont play with skb->truesize net: sctp: sctp_auth_key_put: use kzfree instead of kfree netback: correct netbk_tx_err to handle wrap around. xen/netback: free already allocated memory on failure in xen_netbk_get_requests xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop. xen/netback: shutdown the ring if it contains garbage. net: qmi_wwan: add more Huawei devices, including E320 net: cdc_ncm: add another Huawei vendor specific device ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit() tcp: fix for zero packets_in_flight was too broad brcmsmac: rework of mac80211 .flush() callback operation ssb: unregister gpios before unloading ssb bcma: unregister gpios before unloading bcma rtlwifi: Fix scheduling while atomic bug net: usbnet: fix tx_dropped statistics tcp: ipv6: Update MIB counters for drops ...
2013-02-08Merge branch 'sctp_keys'David S. Miller
Daniel Borkmann says: ==================== Cryptographically used keys should be zeroed out when our session ends resp. memory is freed, thus do not leave them somewhere in the memory. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08net: sctp: sctp_endpoint_free: zero out secret key dataDaniel Borkmann
On sctp_endpoint_destroy, previously used sensitive keying material should be zeroed out before the memory is returned, as we already do with e.g. auth keys when released. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfreeDaniel Borkmann
In sctp_setsockopt_auth_key, we create a temporary copy of the user passed shared auth key for the endpoint or association and after internal setup, we free it right away. Since it's sensitive data, we should zero out the key before returning the memory back to the allocator. Thus, use kzfree instead of kfree, just as we do in sctp_auth_key_put(). Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08atm/iphase: rename fregt_t -> ffreg_tHeiko Carstens
We have conflicting type qualifiers for "freg_t" in s390's ptrace.h and the iphase atm device driver, which causes the compile error below. Unfortunately the s390 typedef can't be renamed, since it's a user visible api, nor can I change the include order in s390 code to avoid the conflict. So simply rename the iphase typedef to a new name. Fixes this compile error: In file included from drivers/atm/iphase.c:66:0: drivers/atm/iphase.h:639:25: error: conflicting type qualifiers for 'freg_t' In file included from next/arch/s390/include/asm/ptrace.h:9:0, from next/arch/s390/include/asm/lowcore.h:12, from next/arch/s390/include/asm/thread_info.h:30, from include/linux/thread_info.h:54, from include/linux/preempt.h:9, from include/linux/spinlock.h:50, from include/linux/seqlock.h:29, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/atm/iphase.c:43: next/arch/s390/include/uapi/asm/ptrace.h:197:3: note: previous declaration of 'freg_t' was here Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: chas williams - CONTRACTOR <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is alignedWill Deacon
We have received multiple reports of mmap failures when running with a 2:2 vm split. These manifest as either -EINVAL with a non page-aligned address (ending 0xaaa) or a SEGV, depending on the application. The issue is commonly observed in children of make, which appears to use bottom-up mmap (assumedly because it changes the stack rlimit). Further investigation reveals that this regression was triggered by 394ef6403abc ("mm: use vm_unmapped_area() on arm architecture"), whereby TASK_UNMAPPED_BASE is no longer page-aligned for bottom-up mmap, causing get_unmapped_area to choke on misaligned addressed. This patch fixes the problem by defining TASK_UNMAPPED_BASE in terms of TASK_SIZE and explicitly aligns the result to 16M, matching the other end of the heap. Acked-by: Nicolas Pitre <nico@linaro.org> Reported-by: Steve Capper <steve.capper@arm.com> Reported-by: Jean-Francois Moine <moinejf@free.fr> Reported-by: Christoffer Dall <cdall@cs.columbia.edu> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08ARM: DMA mapping: fix bad atomic testRussell King
Realview fails to boot with this warning: BUG: spinlock lockup suspected on CPU#0, init/1 lock: 0xcf8bde10, .magic: dead4ead, .owner: init/1, .owner_cpu: 0 Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:cf8bde10 r5:cf83d1c0 r4:cf8bde10 r3:cf83d1c0 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c018926c>] (spin_dump+0x84/0x98) [<c01891e8>] (spin_dump+0x0/0x98) from [<c0189460>] (do_raw_spin_lock+0x100/0x198) [<c0189360>] (do_raw_spin_lock+0x0/0x198) from [<c032cbac>] (_raw_spin_lock+0x3c/0x44) [<c032cb70>] (_raw_spin_lock+0x0/0x44) from [<c01c9224>] (pl011_console_write+0xe8/0x11c) [<c01c913c>] (pl011_console_write+0x0/0x11c) from [<c002aea8>] (call_console_drivers.clone.7+0xdc/0x104) [<c002adcc>] (call_console_drivers.clone.7+0x0/0x104) from [<c002b320>] (console_unlock+0x2e8/0x454) [<c002b038>] (console_unlock+0x0/0x454) from [<c002b8b4>] (vprintk_emit+0x2d8/0x594) [<c002b5dc>] (vprintk_emit+0x0/0x594) from [<c0329718>] (printk+0x3c/0x44) [<c03296dc>] (printk+0x0/0x44) from [<c002929c>] (warn_slowpath_common+0x28/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c) [<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0070ab0>] (lockdep_trace_alloc+0xd8/0xf0) [<c00709d8>] (lockdep_trace_alloc+0x0/0xf0) from [<c00c0850>] (kmem_cache_alloc+0x24/0x11c) [<c00c082c>] (kmem_cache_alloc+0x0/0x11c) from [<c00bb044>] (__get_vm_area_node.clone.24+0x7c/0x16c) [<c00bafc8>] (__get_vm_area_node.clone.24+0x0/0x16c) from [<c00bb7b8>] (get_vm_area_caller+0x48/0x54) [<c00bb770>] (get_vm_area_caller+0x0/0x54) from [<c0020064>] (__alloc_remap_buffer.clone.15+0x38/0xb8) [<c002002c>] (__alloc_remap_buffer.clone.15+0x0/0xb8) from [<c0020244>] (__dma_alloc+0x160/0x2c8) [<c00200e4>] (__dma_alloc+0x0/0x2c8) from [<c00204d8>] (arm_dma_alloc+0x88/0xa0)[<c0020450>] (arm_dma_alloc+0x0/0xa0) from [<c00beb00>] (dma_pool_alloc+0xcc/0x1a8) [<c00bea34>] (dma_pool_alloc+0x0/0x1a8) from [<c01a9d14>] (pl08x_fill_llis_for_desc+0x28/0x568) [<c01a9cec>] (pl08x_fill_llis_for_desc+0x0/0x568) from [<c01aab8c>] (pl08x_prep_slave_sg+0x258/0x3b0) [<c01aa934>] (pl08x_prep_slave_sg+0x0/0x3b0) from [<c01c9f74>] (pl011_dma_tx_refill+0x140/0x288) [<c01c9e34>] (pl011_dma_tx_refill+0x0/0x288) from [<c01ca748>] (pl011_start_tx+0xe4/0x120) [<c01ca664>] (pl011_start_tx+0x0/0x120) from [<c01c54a4>] (__uart_start+0x48/0x4c) [<c01c545c>] (__uart_start+0x0/0x4c) from [<c01c632c>] (uart_start+0x2c/0x3c) [<c01c6300>] (uart_start+0x0/0x3c) from [<c01c795c>] (uart_write+0xcc/0xf4) [<c01c7890>] (uart_write+0x0/0xf4) from [<c01b0384>] (n_tty_write+0x1c0/0x3e4) [<c01b01c4>] (n_tty_write+0x0/0x3e4) from [<c01acfe8>] (tty_write+0x144/0x240) [<c01acea4>] (tty_write+0x0/0x240) from [<c01ad17c>] (redirected_tty_write+0x98/0xac) [<c01ad0e4>] (redirected_tty_write+0x0/0xac) from [<c00c371c>] (vfs_write+0xbc/0x150) [<c00c3660>] (vfs_write+0x0/0x150) from [<c00c39c0>] (sys_write+0x4c/0x78) [<c00c3974>] (sys_write+0x0/0x78) from [<c0014460>] (ret_fast_syscall+0x0/0x3c) This happens because the DMA allocation code is not respecting atomic allocations correctly. GFP flags should not be tested for GFP_ATOMIC to determine if an atomic allocation is being requested. GFP_ATOMIC is not a flag but a value. The GFP bitmask flags are all prefixed with __GFP_. The rest of the kernel tests for __GFP_WAIT not being set to indicate an atomic allocation. We need to do the same. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08ARM: realview: ensure that we have sufficient IRQs availableRussell King
Realview EB with a rev B MPcore tile results in lots of warnings at boot because it can't allocate enough IRQs. Fix this by increasing the number of available IRQs. WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:757 gic_init_bases+0x12c/0x2ec() Cannot allocate irq_descs @ IRQ96, assuming pre-allocated Modules linked in: Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002f5 r5:c042c62c r4:c044ff40 r3:c045f240 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029384>] (warn_slowpath_fmt+0x38/0x40) [<c002934c>] (warn_slowpath_fmt+0x0/0x40) from [<c042c62c>] (gic_init_bases+0x12c/0x2ec) [<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8) [<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24) [<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300) [<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070) ---[ end trace 1b75b31a2719ed1c ]--- ------------[ cut here ]------------ WARNING: at /home/rmk/git/linux-rmk/kernel/irq/irqdomain.c:234 irq_domain_add_legacy+0x80/0x140() Modules linked in: Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000000ea r5:c0081a38 r4:00000000 r3:c045f240 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c) [<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0081a38>] (irq_domain_add_legacy+0x80/0x140) [<c00819b8>] (irq_domain_add_legacy+0x0/0x140) from [<c042c64c>] (gic_init_bases+0x14c/0x2ec) [<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8) [<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24) [<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300) [<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070) ---[ end trace 1b75b31a2719ed1d ]--- ------------[ cut here ]------------ WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:762 gic_init_bases+0x170/0x2ec() Modules linked in: Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002fa r5:c042c670 r4:00000000 r3:c045f240 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c) [<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c042c670>] (gic_init_bases+0x170/0x2ec) [<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8) [<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24) [<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300) [<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070) ---[ end trace 1b75b31a2719ed1e ]--- Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08ARM: GIC: fix GIC cpumask initializationRussell King
Punit Agrawal reports: > I was trying to boot 3.8-rc5 on Realview EB 11MPCore using > realview-smp_defconfig as a starting point but the kernel failed to > progress past the log below (config attached). > > Pawel suggested I try reverting 384a290283f - "ARM: gic: use a private > mapping for CPU target interfaces" that you've authored. With this > commit reverted the kernel boots. > > I am not quite sure why the commit breaks 11MPCore but Pawel (cc'd) > might be able to shed light on that. Some early GIC implementations return zero for the first distributor CPU routing register. This means we can't rely on that telling us which CPU interface we're connected to. We know that these platforms implement PPIs for IRQs 29-31 - but we shouldn't assume that these will always be populated. So, instead, scan for a non-zero CPU routing register in the first 32 IRQs and use that as our CPU mask. Reported-by: Punit Agrawal <punit.agrawal@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull drm regression fix from Dave Airlie: "This one fixes a sleep while locked regression that was introduced earlier in 3.8." * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try
2013-02-08net: usb: fix regression from FLAG_NOARP codeLucas Stach
In commit 6509141f9c2ba74df6cc72ec35cd1865276ae3a4 ("usbnet: add new flag FLAG_NOARP for usb net devices"), the newly added flag NOARP was using an already defined value, which broke drivers using flag MULTI_PACKET. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08l2tp: dont play with skb->truesizeEric Dumazet
Andrew Savchenko reported a DNS failure and we diagnosed that some UDP sockets were unable to send more packets because their sk_wmem_alloc was corrupted after a while (tx_queue column in following trace) $ cat /proc/net/udp sl local_address rem_address st tx_queue rx_queue tr tm->when retrnsmt uid timeout inode ref pointer drops ... 459: 00000000:0270 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4507 2 ffff88003d612380 0 466: 00000000:0277 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4802 2 ffff88003d613180 0 470: 076A070A:007B 00000000:0000 07 FFFF4600:00000000 00:00000000 00000000 123 0 5552 2 ffff880039974380 0 470: 010213AC:007B 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4986 2 ffff88003dbd3180 0 470: 010013AC:007B 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4985 2 ffff88003dbd2e00 0 470: 00FCA8C0:007B 00000000:0000 07 FFFFFB00:00000000 00:00000000 00000000 0 0 4984 2 ffff88003dbd2a80 0 ... Playing with skb->truesize is tricky, especially when skb is attached to a socket, as we can fool memory charging. Just remove this code, its not worth trying to be ultra precise in xmit path. Reported-by: Andrew Savchenko <bircoph@gmail.com> Tested-by: Andrew Savchenko <bircoph@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08net: sctp: sctp_auth_key_put: use kzfree instead of kfreeDaniel Borkmann
For sensitive data like keying material, it is common practice to zero out keys before returning the memory back to the allocator. Thus, use kzfree instead of kfree. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08Merge branch 'fixes' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch into openvswitch Jesse Gross says: ==================== One bug fix for net/3.8 for a long standing problem that was reported a few times recently. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08Merge branch 'netback'David S. Miller
Ian Campbell says: ==================== The Xen netback implementation contains a couple of flaws which can allow a guest to cause a DoS in the backend domain, potentially affecting other domains in the system. CVE-2013-0216 is a failure to sanity check the ring producer/consumer pointers which can allow a guest to cause netback to loop for an extended period preventing other work from occurring. CVE-2013-0217 is a memory leak on an error path which is guest triggerable. The following series contains the fixes for these issues, as previously included in Xen Security Advisory 39: http://lists.xen.org/archives/html/xen-announce/2013-02/msg00001.html Changes in v2: - Typo and block comment format fixes - Added stable Cc ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08netback: correct netbk_tx_err to handle wrap around.Ian Campbell
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08xen/netback: free already allocated memory on failure in xen_netbk_get_requestsIan Campbell
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.Matthew Daley
Signed-off-by: Matthew Daley <mattjd@gmail.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08xen/netback: shutdown the ring if it contains garbage.Ian Campbell
A buggy or malicious frontend should not be able to confuse netback. If we spot anything which is not as it should be then shutdown the device and don't try to continue with the ring in a potentially hostile state. Well behaved and non-hostile frontends will not be penalised. As well as making the existing checks for such errors fatal also add a new check that ensures that there isn't an insane number of requests on the ring (i.e. more than would fit in the ring). If the ring contains garbage then previously is was possible to loop over this insane number, getting an error each time and therefore not generating any more pending requests and therefore not exiting the loop in xen_netbk_tx_build_gops for an externded period. Also turn various netdev_dbg calls which no precipitate a fatal error into netdev_err, they are rate limited because the device is shutdown afterwards. This fixes at least one known DoS/softlockup of the backend domain. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux Pull virtio fix from Rusty Russell: "Obviously I forgot to push this before linux.conf.au..." * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: virtio_console: Don't access uninitialized data.
2013-02-08Merge tag 'rdma-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband Pull IB regression fixes from Roland Dreier: - Fix mlx4 VFs not working on old guests because of 64B CQE changes - Fix ill-considered sparse fix for qib - Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1 * tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/qib: Fix for broken sparse warning fix mlx4_core: Fix advertisement of wrong PF context behaviour IPoIB: Fix crash due to skb double destruct
2013-02-08Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs Pull btrfs fixes from Chris Mason: "We've got corner cases for updating i_size that ceph was hitting, error handling for quotas when we run out of space, a very subtle snapshot deletion race, a crash while removing devices, and one deadlock between subvolume creation and the sb_internal code (thanks lockdep)." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: move d_instantiate outside the transaction during mksubvol Btrfs: fix EDQUOT handling in btrfs_delalloc_reserve_metadata Btrfs: fix possible stale data exposure Btrfs: fix missing i_size update Btrfs: fix race between snapshot deletion and getting inode Btrfs: fix missing release of the space/qgroup reservation in start_transaction() Btrfs: fix wrong sync_writers decrement in btrfs_file_aio_write() Btrfs: do not merge logged extents if we've removed them from the tree btrfs: don't try to notify udev about missing devices
2013-02-08Merge tag 'pinctrl-for-v3.8-late' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull late pinctrl fixes from Linus Walleij: "Two patches appeared as of late, one was completely news to me, the other one was rotated in -next for the next merge window but turned out to be a showstopper. - Exynos Kconfig fixup - SIRF DT translation bug" * tag 'pinctrl-for-v3.8-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: sirf: replace of_gpio_simple_xlate by sirf specific of_xlate pinctrl: exynos: change PINCTRL_EXYNOS option
2013-02-08Merge tag 'stable/for-linus-3.8-rc6-tag' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull Xen fixes from Konrad Rzeszutek Wilk: "This has two fixes. One is a security fix wherein we would spam the kernel printk buffer if one of the guests was misbehaving. The other is much tamer and it was us only checking for one type of error from the IRQ subsystem (when allocating new IRQs) instead of for all of them. - Fix an IRQ allocation where we only check for a specific error (-1). - CVE-2013-0231 / XSA-43. Make xen-pciback rate limit error messages from xen_pcibk_enable_msi{,x}()" * tag 'stable/for-linus-3.8-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen: fix error handling path if xen_allocate_irq_dynamic fails xen-pciback: rate limit error messages from xen_pcibk_enable_msi{,x}()
generated by cgit v0.10.2 at 2024-11-07 21:13:45 (GMT)