| Age | Commit message (Collapse) | Author |
|---|
|
adapter could remain uninitialized if probe fails for some reason.
A null pointer access could cause a crash if be_shutdown
is called after that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch contains a fix for gracefully handling firmware heartbeat
failure instead of forcing panic.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes spin_locks at CAN socket creation time by using RCU.
Inspired by the discussion with Kurt van Dijck and Eric Dumazet the RCU code
was partly derived from af_phonet.c
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next-2.6
|
|
When an interrupt occurs, the INT pin is driven low by the
MCP251x controller (falling edge) but in some cases the INT
pin can be connected to the MPU through a transistor or level
translator which inverts this signal. In this case interrupt
should be configured in rising edge.
This patch adds support to pass the IRQ flags via
mcp251x_platform_data.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When SMSC911X_SAVE_MAC_ADDRESS flag is enabled the driver calls
smsc911x_mac_read and smsc911x_mac_read function without acquiring mac_lock
spinlock
This patch fixes following warning
smsc911x: Driver version 2008-10-21.
------------[ cut here ]------------
WARNING: at drivers/net/smsc911x.c:261 smsc911x_mac_read+0x24/0x220()
Modules linked in:
[<c0060858>] (unwind_backtrace+0x0/0xe0) from [<c009322c>] (warn_slowpath_common+0x4c/0x64)
[<c009322c>] (warn_slowpath_common+0x4c/0x64) from [<c009325c>] (warn_slowpath_null+0x18/0x1c)
[<c009325c>] (warn_slowpath_null+0x18/0x1c) from [<c0324bec>] (smsc911x_mac_read+0x24/0x220)
[<c0324bec>] (smsc911x_mac_read+0x24/0x220) from [<c0434788>] (smsc911x_read_mac_address+0x18/0x6c)
[<c0434788>] (smsc911x_read_mac_address+0x18/0x6c) from [<c0434c74>] (smsc911x_drv_probe+0x498/0x1788)
[<c0434c74>] (smsc911x_drv_probe+0x498/0x1788) from [<c02d3e54>] (platform_drv_probe+0x14/0x18)
[<c02d3e54>] (platform_drv_probe+0x14/0x18) from [<c02d2d60>] (driver_probe_device+0xc8/0x184)
[<c02d2d60>] (driver_probe_device+0xc8/0x184) from [<c02d2e84>] (__driver_attach+0x68/0x8c)
[<c02d2e84>] (__driver_attach+0x68/0x8c) from [<c02d1fc8>] (bus_for_each_dev+0x48/0x74)
[<c02d1fc8>] (bus_for_each_dev+0x48/0x74) from [<c02d2660>] (bus_add_driver+0x9c/0x228)
[<c02d2660>] (bus_add_driver+0x9c/0x228) from [<c02d3598>] (driver_register+0xa0/0x124)
[<c02d3598>] (driver_register+0xa0/0x124) from [<c0050668>] (do_one_initcall+0x94/0x168)
[<c0050668>] (do_one_initcall+0x94/0x168) from [<c0008984>] (kernel_init+0xa0/0x154)
[<c0008984>] (kernel_init+0xa0/0x154) from [<c005afac>] (kernel_thread_exit+0x0/0x8)
---[ end trace 2c931a35b7885770 ]---
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a 5717 or 5719 NVRAM part is manually strapped and is 2mb in size,
the driver needs to look at the NVRAM size field rather than infer it
from the strapping itself.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 5720 device ID to the PCI table, thus enabling 5720
support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 5720 PHY ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the new Host to BMC feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5720 implements its own NVRAM pin strapping scheme. This patch adds
the required support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the 5720 ASIC rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reintroduces the TG3_FLG3_5717_PLUS to identify 5717 and
later devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 57765 arrived before the 5717 and has a subset of the features
supported by the 5717. This patch renames the 5717_PLUS flag so that it
can be reintroduced to designate only 5717 and later devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardcoded values are used in multiple places to describe the maximum rx
ring sizes. This patch replaces those values with preprocessor
constants. This patch also introduces a new TG3_FLG3_LRG_PROD_RING_CAP
to determine if the device is capable of supporting larger ring sizes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The ethtool ETHTOOL_PHYS_ID command runs for an arbitrarily long
period of time, holding the RTNL lock. This blocks routing updates,
device enumeration, and various important operations that one might
want to keep running while hunting for the flashing LED.
We need to drop the RTNL lock during this operation, but currently the
core implementation is a thin wrapper around a driver operation and
drivers may well depend upon holding the lock.
Define a new driver operation 'set_phys_id' with an argument that sets
the ID indicator on/off/inactive/active (the last optional, for any
driver or firmware that prefers to handle blinking asynchronously).
When this is defined, the ethtool core drops the lock while waiting
and only acquires it around calls to this operation.
Deprecate the 'phys_id' operation in favour of this. It can be
removed once all in-tree drivers are converted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Briefly document all operations (except get_rx_ntuple), including
whether they may return an error code and whether they are deprecated.
Also mention some things that should be handled by the ethtool core
rather than by drivers.
Briefly document general requirements for callers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The TSO code already supports IPv6 on VLAN, so enable it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This patch uses __copy_from_user_nocache on transmit to bypass data
cache for a performance improvement. skb_add_data_nocache and
skb_copy_to_page_nocache can be called by sendmsg functions to use
this feature, initial support is in tcp_sendmsg. This functionality is
configurable per device using ethtool.
Presumably, this feature would only be useful when the driver does
not touch the data. The feature is turned on by default if a device
indicates that it does some form of checksum offload; it is off by
default for devices that do no checksum offload or indicate no checksum
is necessary. For the former case copy-checksum is probably done
anyway, in the latter case the device is likely loopback in which case
the no cache copy is probably not beneficial.
This patch was tested using 200 instances of netperf TCP_RR with
1400 byte request and one byte reply. Platform is 16 core AMD x86.
No-cache copy disabled:
672703 tps, 97.13% utilization
50/90/99% latency:244.31 484.205 1028.41
No-cache copy enabled:
702113 tps, 96.16% utilization,
50/90/99% latency 238.56 467.56 956.955
Using 14000 byte request and response sizes demonstrate the
effects more dramatically:
No-cache copy disabled:
79571 tps, 34.34 %utlization
50/90/95% latency 1584.46 2319.59 5001.76
No-cache copy enabled:
83856 tps, 34.81% utilization
50/90/95% latency 2508.42 2622.62 2735.88
Note especially the effect on latency tail (95th percentile).
This seems to provide a nice performance improvement and is
consistent in the tests I ran. Presumably, this would provide
the greatest benfits in the presence of an application workload
stressing the cache and a lot of transmit data happening.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apply restrictions on STP parameters based 802.1D 1998 standard.
* Fixes missing locking in set path cost ioctl
* Uses common code for both ioctl and sysfs
This is based on an earlier patch Sasikanth V but with overhaul.
Note:
1. It does NOT enforce the restriction on the relationship max_age and
forward delay or hello time because in existing implementation these are
set as independant operations.
2. If STP is disabled, there is no restriction on forward delay
3. No restriction on holding time because users use Linux code to act
as hub or be sticky.
4. Although standard allow 0-255, Linux only allows 0-63 for port priority
because more bits are reserved for port number.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink device ops to allow creating bridge device via netlink.
This works in a manner similar to vlan, macvlan and bonding.
Example:
# ip link add link dev br0 type bridge
# ip link del dev br0
The change required rearranging initializtion code to deal with
being called by create link. Most of the initialization happens
in br_dev_setup, but allocation of stats is done in ndo_init callback
to deal with allocation failure. Sysfs setup has to wait until
after the network device kobject is registered.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use RTM_NEWNEIGH and RTM_DELNEIGH to allow updating of entries
in bridge forwarding table. This allows manipulating static entries
which is not possible with existing tools.
Example (using bridge extensions to iproute2)
# br fdb add 00:02:03:04:05:06 dev eth0
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows applications to query and monitor bridge forwarding
table in the same method used for neighbor table. The forward table
entries are returned in same structure format as used by the ioctl.
If more information is desired in future, the netlink method is
extensible.
Example (using bridge extensions to iproute2)
# br monitor
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, look up of forward database entry is done with RCU;
and for others no RCU is needed because of locking. Split the two
cases into two differnt loops (and take off inline).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds tracking the last used time in forwarding table.
Rename ageing_timer to updated to better describe it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Later patch provides ability to create non-local static entry.
To make this easier move the updating of the flag values to
after the code that creates entry.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure dst_release() is not called with error pointer. This is
similar to commit 4910ac6c526d2868adcb5893e0c428473de862b5 ("ipv4:
Don't ip_rt_put() an error pointer in RAW sockets.").
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of these devices have appeared "in the wild", and apparently
the Windows driver is perfectly happy to support this EEPROM version.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
{rx,tx}done_work's are only initialized for usb devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some compiler/architecture combinations generate some warnings that are
not seen on my main system. Two of the "warnings" about unitialized variables
are really bugs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cc: <stable@kernel.org>
Reported-by: Mark Davis [via p54/devices wiki]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We were allocating the size of the NVS file struct and not checking
whether the length of the buffer passed was correct before copying it
into the allocated memory. This is a security hole because buffer
overflows can occur if the userspace passes a bigger file than what is
expected.
With this patch, we check if the size of the data passed from
userspace matches the size required.
This bug was introduced in 2.6.36.
Cc: stable@kernel.org
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when
reseting rx idle timer in urb completion handler.
Move timer reseting to tasklet.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch removes the bogus flag introduced by upstream commit
eefdbec1ea8b7093d2c09d1825f68438701723cf. Old code had buffer length check
that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging
enabled bogus flag caused usb_submit_urb fail.
Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion
handler.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092
Reported-by: Jonathan Callen <abcd@gentoo.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cleaning the ieee80211_rx_data.flags field here is wrong, instead the
flags should be valid accross processing the frame on different
interfaces. Fix this by removing the incorrect flags=0 assignment.
Introduced in commit 554891e63a29af35cc6bb403ef34e319518114d0
(mac80211: move packet flags into packet).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The description for buf_size was misleading and
just said you couldn't TX larger aggregates, but
of course you can't TX aggregates in a way that
would exceed the window either, which is possible
even if the aggregates are shorter than that.
Expand the description, thanks to Emmanuel for
explaining this to me.
Cc: Emmanuel Grumbach <egrumbach@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The MODULE_AUTHOR() macro in the main module (wl12xx) has been updated
to reflect one of the author's new email address, but the wl12xx_spi
and wl12xx_sdio modules haven't been updated. This patches updates
them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Otherwise, skb_put inside of dma_rx can fail...
https://bugzilla.kernel.org/show_bug.cgi?id=32042
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
|
|
This is an implementation of the Quick Fair Queue scheduler developed
by Fabio Checconi. The same algorithm is already implemented in ipfw
in FreeBSD. Fabio had an earlier version developed on Linux, I just
cleaned it up. Thanks to Eric Dumazet for testing this under load.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
setup
We need to assume that all features will be available when registering the
netdev otherwise they are ommitted from the initial set of
dev->wanted_features. When we connect to the backed we reduce the set as
necessary due to the call to netdev_update_features() in xennet_connect().
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
--ctdir ORIGINAL matches REPLY packets, and vv:
userspace sets "invert_flags &= ~XT_CONNTRACK_DIRECTION" in ORIGINAL
case.
Thus: (CTINFO2DIR(ctinfo) == IP_CT_DIR_ORIGINAL) ^
!!(info->invert_flags & XT_CONNTRACK_DIRECTION))
yields "1 ^ 0", which is true -> returns false.
Reproducer:
iptables -I OUTPUT 1 -p tcp --syn -m conntrack --ctdir ORIGINAL
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
This avoids pulling in the ipv6 module when using (ipv4-only) iptables
-m addrtype.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
ipv6 fib lookup can set RT6_LOOKUP_F_IFACE flag to restrict search
to an interface, but this flag cannot be set via struct flowi.
Also, it cannot be set via ip6_route_output: this function uses the
passed sock struct to determine if this flag is required
(by testing for nonzero sk_bound_dev_if).
Work around this by passing in an artificial struct sk in case
'strict' argument is true.
This is required to replace the rt6_lookup call in xt_addrtype.c with
nf_afinfo->route().
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
This is required to eventually replace the rt6_lookup call in
xt_addrtype.c with nf_afinfo->route().
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
