summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-10-09net: Distributed Switch Architecture protocol supportLennert Buytenhek
Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-098139too: move wmb before TX DMA startAndreas Oberritter
The write barrier should be used before starting a DMA transfer. This fixes a problem, where almost all packets received on another machine had garbled content. Tested with an RTL8100C on a MIPS machine. Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09netdev: uniquify the tx_timeout nameArjan van de Ven
there's several drivers that have use "tx_timeout" for the .. tx timeout function. All fine with that, they're static, however for doing stats on how often which driver hits the timeout it's a tad unfortunate. The patch below gives the ones I found in the kerneloops.org database unique names. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09drivers/net/usb/Makefile - shrink logspamDavid Brownell
When building with CONFIG_USB_DEBUG, don't create logspam from the USB networking drivers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09r8169: WoL fixes, part 2.Bruno Prémont
Since recent kernel (2.6.26 or 2.6.27) the PCI wakeup functions are influenced by generic device ability and configuration when enabling PCI-device triggered wake-up. This patch causes WoL setting to enable/disable device's wish to be permitted to wake-up the host when changing WoL options and also during device probing. Without this patch one has write 'enabled' to /sys/bus/pci/devices/0000:02:08.0/power/wakeup Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09r8169: WoL fixes, part 1.Bruno Prémont
When probing the chip and handling it's power management settings also remember wether WoL feature is enabled. Without this patch one has to call ethtool to change WoL settings for this flag to be set and any WoL being enabled on suspend to RAM. Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09gianfar: Create net device with carrier downTrent Piepho
The device's carrier status is controlled via the functions netif_carrier_on() and netif_carrier_off(). These set or clear a bit indicating the carrier (aka lower level link) is down, and if the state changed, they fire off a routing netlink event. Add a call to netif_carrier_off() before register_netdev() so that the newly created device will be set to carrier down. Then when the carrier comes up for the first time, a netlink event will be generated, as the carrier changed from down to up. Otherwise the initial carrier up will appear to be changing the status from up to up, and so no event is generated since that's not a change. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09mv643xx_eth: include linux/ip.h to fix buildLennert Buytenhek
mv643xx_eth uses ip_hdr() (defined in linux/ip.h), but relied on another header file to include the needed header file indirectly. In latest net-next this indirect include chain is gone, so the driver fails to build. Include linux/ip.h explicitly to fix this. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08lib8390: Fix locking in ei_poll (poll controller)Jarek Poplawski
This lockdep warning: ================================= [ INFO: inconsistent lock state ] 2.6.27-rc7 #3 --------------------------------- inconsistent {in-softirq-W} -> {softirq-on-W} usage. syslogd/2474 [HC0[0]:SC0[0]:HE1:SE1] takes: (_xmit_ETHER#2){-+..}, at: [<c0265562>] netpoll_send_skb+0x132/0x190 ... is caused by unconditional local_irq_disable()/local_irq_enable() in disable_irq_lockdep()/enable_irq_lockdep() used by __ei_poll(). Since netconsole/netpoll always calls dev->poll_controller() with local irqs disabled, disable_irq()/enable_irq() instead is safe and enough (like e.g. in 3c509 or 8139xx drivers). Reported-and-tested-by: Bernard Pidoux F6BVP <f6bvp@free.fr> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08ixgb: fix bug when freeing resourcesBrandeburg, Jesse
It was pointed out by Breno Leitao <leitao@linux.vnet.ibm.com> that ixgb would crash on PPC when an IOMMU was in use, if change_mtu was called. It appears to be a pretty simple issue in the driver that wasn't discovered because most systems don't run with an IOMMU. The driver needs to only unmap buffers that are mapped (duh). CC: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08e1000e: release hw semaphore after successfully writing EEPROMArthur Jones
Since e1000e has been existance in linux-2.6, we've never released the hardware semaphore after a successful write to the SPI EEPROM. I guess we don't write to SPI EEPROM much -- but those few of us that do appreciate it when we can later read from the EEPROM without having to reboot. Found-by: Nick Van Fossen <Nick.VanFossen@riverbed.com> Signed-off-by: Arthur Jones <ajones@riverbed.com> Reviewed-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driverSteve Glendinning
Attached is a driver for SMSC's LAN9500 USB2.0 10/100 ethernet adapter. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08phylib: add mdiobus_{read,write}Lennert Buytenhek
Add mdiobus_{read,write} routines to allow direct reading/writing of registers on an mii bus without having to go through the PHY abstraction, and make phy_{read,write} use these primitives. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08phylib: give mdio buses a device tree presenceLennert Buytenhek
Introduce the mdio_bus class, and give each 'struct mii_bus' its own 'struct device', so that mii_bus objects are represented in the device tree and can be found by querying the device tree. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08phylib: move to dynamic allocation of struct mii_busLennert Buytenhek
This patch introduces mdiobus_alloc() and mdiobus_free(), and makes all mdio bus drivers use these functions to allocate their struct mii_bus'es dynamically. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Andy Fleming <afleming@freescale.com>
2008-10-08phylib: rename mii_bus::dev to mii_bus::parentLennert Buytenhek
In preparation of giving mii_bus objects a device tree presence of their own, rename struct mii_bus's ->dev argument to ->parent, since having a 'struct device *dev' that points to our parent device conflicts with introducing a 'struct device dev' representing our own device. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Andy Fleming <afleming@freescale.com>
2008-10-08myri10ge: add multiqueue TXBrice Goglin
Add multiqueue TX support to myri10ge. [ Removed reference to deprecated CONFIG_NETDEVICES_MULTIQUEUE and NETIF_F_MULTI_QUEUE ] Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08atl1: update introductory commentsJay Cliburn
Update the driver's introductory comments. Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08atl1: remove EXPERIMENTAL labelJay Cliburn
Remove the EXPERIMENTAL label from the atl1 driver and change the vendor name to include Attansic's successor, Atheros. We'll leave Attansic in the name since Attansic's PCI ID (1969) is encoded in the PCI config and is what users encounter on their systems. Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08atl1: remove LLTXJay Cliburn
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver and remove the NETIF_F_LLTX feature flag. Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08atl1: fix transmit timeout bugJay Cliburn
See http://marc.info/?l=linux-netdev&m=121931988219314&w=2 Stop the queue and turn off carrier to prevent transmit timeouts when the cable is unplugged/replugged. Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08skge: Fix skge_set_ring_param() losing error returnWang Chen
The error return is useful to caller, driver shouldn't miss it. Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08[10/21] driver/net/skge.c: restart the interface when it's options orXiaoming.Zhang
pauseparam is set On Wednesday 24 September 2008 07:47, Stephen Hemminger wrote: > On Mon, 22 Sep 2008 14:52:17 -0700 > > akpm@linux-foundation.org wrote: > > From: "Xiaoming.Zhang" <Xiaoming.Zhang@resilience.com> > > > > We have an issue of the skge driver: The card won't work when it's > > options are changed. Here's the hardware info: > > > > # lspci -v > > 05:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 > > Gigabit Ethernet Controller (rev 13) Subsystem: Marvell Technology Group > > Ltd. Marvell RDK-8001 Flags: bus master, 66MHz, medium devsel, latency > > 32, IRQ 16 Memory at d042c000 (32-bit, non-prefetchable) [size=16K] I/O > > ports at d000 [size=256] > > [virtual] Expansion ROM at 20400000 [disabled] [size=128K] > > Capabilities: [48] Power Management version 2 > > Capabilities: [50] Vital Product Data > > > > The happens in both Linux-2.6.26(skge version 1.23) and RHEL5.2(skge > > version 1.6). > > > > For example, at first it is set to "speed 1000 duplex full auto-neg on" > > and it works, then run > > > > ethtool -s <ethx> autoneg off > > or ethtool -s <ethx> speed 100 duplex full autoneg off > > > > Then it will stop working. After that if we restart the interface: > > > > ifconifg <ethx> down > > ifconfig <ethx> up > > > > It will work again. And `ethtool -A' has the same issue. > > > > So we think after setting the options, the interface should be restarted. > > > > Signed-off-by: Zhang Xiaoming <xiaoming.zhang@resilience.com> > > Cc: Stephen Hemminger <shemminger@vyatta.com> > > Cc: Jeff Garzik <jeff@garzik.org> > > Signed-off-by: Andrew Morton <akpm@linux-foundation.org> > > --- > > > > drivers/net/skge.c | 12 ++++++++---- > > 1 file changed, 8 insertions(+), 4 deletions(-) > > > > diff -puN > > drivers/net/skge.c~driver-net-skgec-restart-the-interface-when-its-option > >s-or-pauseparam-is-set drivers/net/skge.c --- > > a/drivers/net/skge.c~driver-net-skgec-restart-the-interface-when-its-opti > >ons-or-pauseparam-is-set +++ a/drivers/net/skge.c > > @@ -353,8 +353,10 @@ static int skge_set_settings(struct net_ > > skge->autoneg = ecmd->autoneg; > > skge->advertising = ecmd->advertising; > > > > - if (netif_running(dev)) > > - skge_phy_reset(skge); > > + if (netif_running(dev)) { > > + skge_down(dev); > > + skge_up(dev); > > + } > > > > return (0); > > } > > @@ -595,8 +597,10 @@ static int skge_set_pauseparam(struct ne > > skge->flow_control = FLOW_MODE_NONE; > > } > > > > - if (netif_running(dev)) > > - skge_phy_reset(skge); > > + if (netif_running(dev)) { > > + skge_down(dev); > > + skge_up(dev); > > + } > > > > return 0; > > } > > Since skge_up can fail because of out of memory, this code needs to > check the return value. And then if it fails the "limbo state" needs > to be handled in skge_down. How about like this? It is tested. Thank you. Signed-off-by: Zhang Xiaoming <xiaoming.zhang@resilience.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08[2.6.28,1/1] cxgb3 - fix race in EEHDivy Le Ray
A SGE queue set timer might access registers while in EEH recovery, triggering an EEH error loop. Stop all timers early in EEH process. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08via-velocity: Fix warnings on sparc64.Francois Romieu
As reported by Meelis Roos. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08net: remove LLTX in atl2 driverKevin Hao
When NETIF_F_LLTX is set, the atlx driver will use a private lock. But in recent kernels this implementation seems redundant and can cause problems where AF_PACKET sees things twice. Since NETIF_F_LLTX is marked as deprecated and shouldn't be used in new driver, this patch removes NETIF_F_LLTX and adds a mmiowb before sending packet. I have tested this driver on a Eee PC. It works well. Signed-off-by: Kevin Hao <kexin.hao@windriver.com> Acked-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08phylib: Wake PHY state machine on interruptTrent Piepho
This way the phy layer will respond to a change in phy state immediately, instead of up to one second later when the state machine timer runs. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08PHY: Avoid unnecessary aneg restartsTrent Piepho
The PHY's aneg is configured and restarted whenever the link is brought up, e.g. when DHCP is started after the kernel has booted. This can take the link down for several seconds while auto-negotiation is redone. If the advertised features haven't changed, then it shouldn't be necessary to bring down the link and start auto-negotiation over again. genphy_config_advert() is enhanced to return 0 when the advertised features haven't been changed and >0 when they have been. genphy_config_aneg() then uses this information to not call genphy_restart_aneg() if there has been no change. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08r8169: read MAC address from EEPROM on initIvan Vecera
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08net: add net poll support for atl2 driverKevin Hao
Add netconsole support for Atheros L2 10/100 network device. Signed-off-by: Kevin Hao <kexin.hao@windriver.com> Acked-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08ibm_newemac: Fix EMAC soft reset on 460EX/GTVictor Gallardo
This patch fixes EMAC soft reset on 460EX/GT when no external clock is available. Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08phylib: phy_mii_ioctl() fixesLennert Buytenhek
Make the SIOCGMIIPHY case fall through properly (it is supposed to not only return the ID of the default PHY but also to read from that PHY), and make phy_mii_ioctl() return the same error code as generic_mii_ioctl() in case of an unsupported operation. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000e/ich8lan.c drivers/net/e1000e/netdev.c
2008-10-08ipvs: Remove stray file left over from ipvs moveSven Wegener
Commit cb7f6a7b716e801097b564dec3ccb58d330aef56 ("IPVS: Move IPVS to net/netfilter/ipvs") has left a stray file in the old location of ipvs. Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08tcpv6: fix option space offsets with md5Ilpo Järvinen
More breakage :-), part of timestamps just were previously overwritten. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08Merge branch 'lvs-next-2.6' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/horms/lvs-2.6 Conflicts: net/netfilter/Kconfig
2008-10-08sctp: shrink sctp_tsnmap some more by removing gabs arrayVlad Yasevich
The gabs array in the sctp_tsnmap structure is only used in one place, sctp_make_sack(). As such, carrying the array around in the sctp_tsnmap and thus directly in the sctp_association is rather pointless since most of the time it's just taking up space. Now, let sctp_make_sack create and populate it and then throw it away when it's done. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08sctp: Rework the tsn map to use generic bitmap.Vlad Yasevich
The tsn map currently use is 4K large and is stuck inside the sctp_association structure making memory references REALLY expensive. What we really need is at most 4K worth of bits so the biggest map we would have is 512 bytes. Also, the map is only really usefull when we have gaps to store and report. As such, starting with minimal map of say 32 TSNs (bits) should be enough for normal low-loss operations. We can grow the map by some multiple of 32 along with some extra room any time we receive the TSN which would put us outside of the map boundry. As we close gaps, we can shift the map to rebase it on the latest TSN we've seen. This saves 4088 bytes per association just in the map alone along savings from the now unnecessary structure members. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08inet: cleanup of local_port_rangeEric Dumazet
I noticed sysctl_local_port_range[] and its associated seqlock sysctl_local_port_range_lock were on separate cache lines. Moreover, sysctl_local_port_range[] was close to unrelated variables, highly modified, leading to cache misses. Moving these two variables in a structure can help data locality and moving this structure to read_mostly section helps sharing of this data among cpus. Cleanup of extern declarations (moved in include file where they belong), and use of inet_get_local_port_range() accessor instead of direct access to ports values. Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08udp: Improve port randomizationEric Dumazet
Current UDP port allocation is suboptimal. We select the shortest chain to chose a port (out of 512) that will hash in this shortest chain. First, it can lead to give not so ramdom ports and ease give attackers more opportunities to break the system. Second, it can consume a lot of CPU to scan all table in order to find the shortest chain. Third, in some pathological cases we can fail to find a free port even if they are plenty of them. This patch zap the search for a short chain and only use one random seed. Problem of getting long chains should be addressed in another way, since we can obtain long chains with non random ports. Based on a report and patch from Vitaly Mayatskikh Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Sibyte: Register PIO PATA device only for Swarm and Litte Sur
2008-10-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd. net: Fix netdev_run_todo dead-lock tcp: Fix possible double-ack w/ user dma net: only invoke dev->change_rx_flags when device is UP netrom: Fix sock_orphan() use in nr_release ax25: Quick fix for making sure unaccepted sockets get destroyed. Revert "ax25: Fix std timer socket destroy handling." [Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle [Bluetooth] Add reset quirk for new Targus and Belkin dongles [Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
2008-10-08pkt_sched: Update qdisc requeue stats in dev_requeue_skb()Jarek Poplawski
After the last change of requeuing there is no info about such incidents in tc stats. This patch updates the counter, but we should consider this should differ from previous stats because of additional checks preventing to repeat this. On the other hand, previous stats didn't include requeuing of gso_segmented skbs. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08tcp: fix length used for checksum in a resetIlpo Järvinen
While looking for some common code I came across difference in checksum calculation between tcp_v6_send_(reset|ack) I couldn't explain. I checked both v4 and v6 and found out that both seem to have the same "feature". I couldn't find anything in rfc nor anywhere else which would state that md5 option should be ignored like it was in case of reset so I came to a conclusion that this is probably a genuine bug. I suspect that addition of md5 just was fooled by the excessive copy-paste code in those functions and the reset part was never tested well enough to find out the problem. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08[MIPS] Sibyte: Register PIO PATA device only for Swarm and Litte SurRalf Baechle
Symbol name spaghetti which is too complicated to cleanup on this stage of the release cycle breaks the build on BCM1480 platforms. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-08ipv6: remove unused not init_ipv6_mibs/cleanup_ipv6_mibsDenis V. Lunev
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08ipv6: making ip and icmp statistics per/namespaceDenis V. Lunev
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08ipv6: added net argument to _DEVINC/_DEVADDDenis V. Lunev
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08ipv6: added net argument to ICMP6MSGIN_INC_STATS_BHDenis V. Lunev
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08ipv6: ICMP6MSGIN_INC_STATS is not usedDenis V. Lunev
Removed. Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>