| Age | Commit message (Collapse) | Author |
|---|
|
Commit 8fb54284ba6a {ARM: mm: Add strongly ordered descriptor support}
added XN flag at section level but missed it at PTE level.
Fix it by adding the L_PTE_XN to MT_MEMORY_SO PTE descriptor.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Subhash Jadavani reported this partial backtrace:
Now consider this call stack from MMC block driver (this is on the ARMv7
based board):
[<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c)
[<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c)
[<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114)
This is caused by incrementing the struct page pointer, and running off
the end of the sparsemem page array. Fix this by incrementing by pfn
instead, and convert the pfn to a struct page.
Cc: <stable@vger.kernel.org>
Suggested-by: James Bottomley <JBottomley@Parallels.com>
Tested-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We currently use a temporary 1MB section aligned to a 1MB boundary for
mapping the provided device tree until the final page table is created.
However, if the device tree happens to cross that 1MB boundary, the end
of it remains unmapped and the kernel crashes when it attempts to access
it. Given no restriction on the location of that DTB, it could end up
with only a few bytes mapped at the end of a section.
Solve this issue by mapping two consecutive sections.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patrik Kluba reports that the preempt count becomes invalid due
to the preempt_enable() call being unbalanced with a
preempt_disable() call in the vfp assembly routines. This happens
because preempt_enable() and preempt_disable() update preempt
counts under PREEMPT_COUNT=y but the vfp assembly routines do so
under PREEMPT=y. In a configuration where PREEMPT=n and
DEBUG_ATOMIC_SLEEP=y, PREEMPT_COUNT=y and so the preempt_enable()
call in VFP_bounce() keeps subtracting from the preempt count
until it goes negative.
Fix this by always using PREEMPT_COUNT to decided when to update
preempt counts in the ARM assembly code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Patrik Kluba <pkluba@dension.com>
Tested-by: Patrik Kluba <pkluba@dension.com>
Cc: <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The use of writel instead of writel_relaxed lead to deadlock in some
situation (SMP on Armada 370 for instance). The use of writel_relaxed
as it was done in the rest of this driver fixes this bug.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
enable
This patch fixes a bug for Aurora L2 cache controller when the
write-through mode is enable. For the clean operation even if we don't
have to flush the lines we still need to invalidate them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If CONFIG_ARCH_MULTIPLATFORM & CONFIG_ARCH_MVEBU are both enabled,
__v7_pj4b_setup is added between __v7_ca9mp_setup and __v7_setup.
But there's no jump instruction added. If the chip is Cortex A5/A9,
it goes through __v7_pj4b_setup also. It results in system hang.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Since commit 62e4d357a (ARM: 7609/1: disable errata work-arounds which access
secure registers) ARM_ERRATA_743622/751472 depends on !ARCH_MULTIPLATFORM.
Since imx has been converted to multiplatform, the following warning happens:
$ make imx_v6_v7_defconfig
warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects
ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 &&
!ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622
which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622
which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects
ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 &&
!ARCH_MULTIPLATFORM)
Recommended approach is to remove ARM_ERRATA_743622/751472 from being selected
by SOC_IMX6Q and apply such workarounds into the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The VIC irqdomain code added in commit
07c9249f1fa90cc8189bed44c0bcece664596a72
"ARM: 7554/1: VIC: use irq_domain_add_simple()"
Had two bugs:
1) It didn't call irq_create_mapping() once on each
valid irq source in the slowpath when registering
the controller.
2) It passed a -1 as IRQ offset for the DT case, whereas
0 should be passed as invalid IRQ instead.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Versatile starts to register Linux IRQ numbers from offset 0
which is illegal, since this is NO_IRQ. Bump all hard-coded IRQs
by 32 to get rid of the problem.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In order to support secure and non-secure platforms in multi-platform
kernels, errata work-arounds that access secure only registers need to
be disabled. Make all the errata options that fit in this category
depend on !CONFIG_ARCH_MULTIPLATFORM.
This will effectively remove the errata options as platforms are
converted over to multi-platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
PL310 errata work-arounds using .set_debug function are only needed on
r3p0 and earlier, so check the rev and only set .set_debug on older revs.
Avoiding debug register accesses fixes aborts on non-secure platforms
like highbank. It is assumed that non-secure platforms needing these
work-arounds have already implemented .set_debug with secure monitor
calls.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull DRM update from Dave Airlie:
"This is a bit larger due to me not bothering to do anything since
before Xmas, and other people working too hard after I had clearly
given up.
It's got the 3 main x86 driver fixes pulls, and a bunch of tegra
fixes, doesn't fix the Ironlake bug yet, but that does seem to be
getting closer.
- radeon: gpu reset fixes and userspace packet support
- i915: watermark fixes, workarounds, i830/845 fix,
- nouveau: nvd9/kepler microcode fixes, accel is now enabled and
working, gk106 support
- tegra: misc fixes."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (34 commits)
Revert "drm: tegra: protect DC register access with mutex"
drm: tegra: program only one window during modeset
drm: tegra: clean out old gem prototypes
drm: tegra: remove redundant tegra2_tmds_config entry
drm: tegra: protect DC register access with mutex
drm: tegra: don't leave clients host1x member uninitialized
drm: tegra: fix front_porch <-> back_porch mixup
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
drm/radeon: add support for MEM_WRITE packet
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
|
|
Pull ARM SoC fixes from Olof Johansson:
"It's been quiet over the holidays, but we have had a couple of trivial
fixes coming in for the newly introduced sunxi platform; one to add it
to the multiplatform defconfig for build coverage, and one fixup for
device tree strings."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
|
|
This reverts commit 83c0bcb694be31dcd6c04bdd935b96a95a0af548.
Lucas pointed out this was a mistake, and I missed the discussion,
so just revert it out to save a rebase.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The intention is to program exactly WIN_A, not WIN_A and possibly
others.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
There is no gem.c anymore, those functions are implemented by the
drm_cma_helpers now.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The 720p and 1080p entries are completely redundant, as we are matching
the table entries against <=pclk.
Also generalize the comment, as we are using those table entries even
when driving other modes than the standard TV ones.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Window properties are programmed through a shared aperture and have to
happen atomically. Also we do the read-update-write dance on some of the
shared regs.
To make sure that different functions don't stumble over each other
protect the register access with a mutex.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
No real problem for now, as nothing is using this, but leaving it
unitialized is asking for trouble later on.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes wrong picture offset observed when using HDMI output with a
Technisat HD TV.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-next
Some fixes for 3.8:
- Watermark fixups from Chris Wilson (4 pieces).
- 2 snb workarounds, seem to be recently added to our internal DB.
- workaround for the infamous i830/i845 hang, seems now finally solid!
Based on Chris' fix for SNA, now also for UXA/mesa&old SNA.
- Some more fixlets for shrinker-pulls-the-rug issues (Chris&me).
- Fix dma-buf flags when exporting (you).
- Disable the VGA plane if it's enabled on lid open - similar fix in
spirit to the one I've sent you last weeek, BIOS' really like to mess
with the display when closing the lid (awesome debug work from Krzysztof
Mazur).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
i915: ensure that VGA plane is disabled
drm/i915: Preallocate the drm_mm_node prior to manipulating the GTT drm_mm manager
drm: Export routines for inserting preallocated nodes into the mm manager
drm/i915: don't disable disconnected outputs
drm/i915: Implement workaround for broken CS tlb on i830/845
drm/i915: Implement WaSetupGtModeTdRowDispatch
drm/i915: Implement WaDisableHiZPlanesWhenMSAAEnabled
drm/i915: Prefer CRTC 'active' rather than 'enabled' during WM computations
drm/i915: Clear self-refresh watermarks when disabled
drm/i915: Double the cursor self-refresh latency on Valleyview
drm/i915: Fixup cursor latency used for IVB lp3 watermarks
|
|
into drm-next
Misc fixes for reset and new packets for userspace usage.
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/radeon: add support for MEM_WRITE packet
drm/radeon: restore modeset late in GPU reset path
drm/radeon: avoid deadlock in pm path when waiting for fence
drm/radeon: don't leave fence blocked process on failed GPU reset
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
Fixes the accel support for nvd9 + kepler chipsets, also fixes GK106 support.
* 'drm-nouveau-fixes-3.8' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
|
|
An unintended consequence of commit 4ae0a48b5efc ("mm: modify
pgdat_balanced() so that it also handles order-0") is that
wait_iff_congested() can now be called with NULL 'struct zone *'
producing kernel oops like this:
BUG: unable to handle kernel NULL pointer dereference
IP: [<ffffffff811542d9>] wait_iff_congested+0x59/0x140
This trivial patch fixes it.
Reported-by: Zhouping Liu <zliu@redhat.com>
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
From Maxime Ripard:
Fixes for the sunxi core to be merged in 3.8-rc2
* tag 'sunxi-fixes-for-3.8-rc2' of git://github.com/mripard/linux:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Report i2c errors to userspace in lm73 driver
- Fix problem with DIV_ROUND_CLOSEST and unsigned divisors in emc6w201
driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (emc6w201) Fix DIV_ROUND_CLOSEST problem with unsigned divisors
hwmon: (lm73} Detect and report i2c bus errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"This tree includes two bug fixes for problems Oleg spotted on his
review of the recent pid namespace work. A small fix to not enable
bottom halves with irqs disabled, and a trivial build fix for f2fs
with user namespaces enabled."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
f2fs: Don't assign e_id in f2fs_acl_from_disk
proc: Allow proc_free_inum to be called from any context
pidns: Stop pid allocation when init dies
pidns: Outlaw thread creation after unshare(CLONE_NEWPID)
|
|
Pull networking fixes from David Miller:
1) GRE tunnel drivers don't set the transport header properly, they also
blindly deref the inner protocol ipv4 and needs some checks. Fixes
from Isaku Yamahata.
2) Fix sleeps while atomic in netdevice rename code, from Eric Dumazet.
3) Fix double-spinlock in solos-pci driver, from Dan Carpenter.
4) More ARP bug fixes. Fix lockdep splat in arp_solicit() and then the
bug accidentally added by that fix. From Eric Dumazet and Cong Wang.
5) Remove some __dev* annotations that slipped back in, as well as all
HOTPLUG references. From Greg KH
6) RDS protocol uses wrong interfaces to access scatter-gather elements,
causing a regression. From Mike Marciniszyn.
7) Fix build error in cpts driver, from Richard Cochran.
8) Fix arithmetic in packet scheduler, from Stefan Hasko.
9) Similarly, fix association during calculation of random backoff in
batman-adv. From Akinobu Mita.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
ipv6/ip6_gre: set transport header correctly
ipv4/ip_gre: set transport header correctly to gre header
IB/rds: suppress incompatible protocol when version is known
IB/rds: Correct ib_api use with gs_dma_address/sg_dma_len
net/vxlan: Use the underlying device index when joining/leaving multicast groups
tcp: should drop incoming frames without ACK flag set
netprio_cgroup: define sk_cgrp_prioidx only if NETPRIO_CGROUP is enabled
cpts: fix a run time warn_on.
cpts: fix build error by removing useless code.
batman-adv: fix random jitter calculation
arp: fix a regression in arp_solicit()
net: sched: integer overflow fix
CONFIG_HOTPLUG removal from networking core
Drivers: network: more __dev* removal
bridge: call br_netpoll_disable in br_add_if
ipv4: arp: fix a lockdep splat in arp_solicit()
tuntap: dont use a private kmem_cache
net: devnet_rename_seq should be a seqcount
ip_gre: fix possible use after free
ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally
...
|
|
ip6gre_xmit2() incorrectly sets transport header to inner payload
instead of GRE header. It seems copy-and-pasted from ipip.c.
Set transport header to gre header.
(In ipip case the transport header is the inner ip header, so that's
correct.)
Found by inspection. In practice the incorrect transport header
doesn't matter because the skb usually is sent to another net_device
or socket, so the transport header isn't referenced.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipgre_tunnel_xmit() incorrectly sets transport header to inner payload
instead of GRE header. It seems copy-and-pasted from ipip.c.
So set transport header to gre header.
(In ipip case the transport header is the inner ip header, so that's
correct.)
Found by inspection. In practice the incorrect transport header
doesn't matter because the skb usually is sent to another net_device
or socket, so the transport header isn't referenced.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an else to only print the incompatible protocol message
when version hasn't been established.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
0b088e00 ("RDS: Use page_remainder_alloc() for recv bufs")
added uses of sg_dma_len() and sg_dma_address(). This makes
RDS DOA with the qib driver.
IB ulps should use ib_sg_dma_len() and ib_sg_dma_address
respectively since some HCAs overload ib_sg_dma* operations.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The socket calls from vxlan to join/leave multicast group aren't
using the index of the underlying device, as a result the stack uses
the first interface that is up. This results in vxlan being non functional
over a device which isn't the 1st to be up.
Fix this by providing the iflink field to the vxlan instance
to the multicast calls.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 96e0bf4b5193d (tcp: Discard segments that ack data not yet
sent) John Dykstra enforced a check against ack sequences.
In commit 354e4aa391ed5 (tcp: RFC 5961 5.2 Blind Data Injection Attack
Mitigation) I added more safety tests.
But we missed fact that these tests are not performed if ACK bit is
not set.
RFC 793 3.9 mandates TCP should drop a frame without ACK flag set.
" fifth check the ACK field,
if the ACK bit is off drop the segment and return"
Not doing so permits an attacker to only guess an acceptable sequence
number, evading stronger checks.
Many thanks to Zhiyun Qian for bringing this issue to our attention.
See :
http://web.eecs.umich.edu/~zhiyunq/pub/ccs12_TCP_sequence_number_inference.pdf
Reported-by: Zhiyun Qian <zhiyunq@umich.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unfortunately with !CONFIG_PAGEFLAGS_EXTENDED, (!PageHead) is false, and
(PageHead) is true, for tail pages. If this is indeed the intended
behavior, which I doubt because it breaks cache cleaning on some ARM
systems, then the nomenclature is highly problematic.
This patch makes sure PageHead is only true for head pages and PageTail
is only true for tail pages, and neither is true for non-compound pages.
[ This buglet seems ancient - seems to have been introduced back in Apr
2008 in commit 6a1e7f777f61: "pageflags: convert to the use of new
macros". And the reason nobody noticed is because the PageHead()
tests are almost all about just sanity-checking, and only used on
pages that are actual page heads. The fact that the old code returned
true for tail pages too was thus not really noticeable. - Linus ]
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Will Deacon <Will.Deacon@arm.com>
Cc: Steve Capper <Steve.Capper@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: stable@kernel.org # 2.6.26+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sock->sk_cgrp_prioidx won't be used at all if CONFIG_NETPRIO_CGROUP=n.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a warning in clk_enable by calling clk_prepare_enable
instead.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpts driver tries to obtain the input clock frequency by calling the
clock's internal 'recalc' method. Since <plat/clock.h> has been removed,
this code can no longer compile.
However, the driver never makes use of the frequency value, so this patch
fixes the issue by removing the offending code altogether.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
batadv_iv_ogm_emit_send_time() attempts to calculates a random integer
in the range of 'orig_interval +- BATADV_JITTER' by the below lines.
msecs = atomic_read(&bat_priv->orig_interval) - BATADV_JITTER;
msecs += (random32() % 2 * BATADV_JITTER);
But it actually gets 'orig_interval' or 'orig_interval - BATADV_JITTER'
because '%' and '*' have same precedence and associativity is
left-to-right.
This adds the parentheses at the appropriate position so that it matches
original intension.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: Antonio Quartulli <ordex@autistici.org>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With user namespaces enabled building f2fs fails with:
CC fs/f2fs/acl.o
fs/f2fs/acl.c: In function ‘f2fs_acl_from_disk’:
fs/f2fs/acl.c:85:21: error: ‘struct posix_acl_entry’ has no member named ‘e_id’
make[2]: *** [fs/f2fs/acl.o] Error 1
make[2]: Target `__build' not remade because of errors.
e_id is a backwards compatibility field only used for file systems
that haven't been converted to use kuids and kgids. When the posix
acl tag field is neither ACL_USER nor ACL_GROUP assigning e_id is
unnecessary. Remove the assignment so f2fs will build with user
namespaces enabled.
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
While testing the pid namespace code I hit this nasty warning.
[ 176.262617] ------------[ cut here ]------------
[ 176.263388] WARNING: at /home/eric/projects/linux/linux-userns-devel/kernel/softirq.c:160 local_bh_enable_ip+0x7a/0xa0()
[ 176.265145] Hardware name: Bochs
[ 176.265677] Modules linked in:
[ 176.266341] Pid: 742, comm: bash Not tainted 3.7.0userns+ #18
[ 176.266564] Call Trace:
[ 176.266564] [<ffffffff810a539f>] warn_slowpath_common+0x7f/0xc0
[ 176.266564] [<ffffffff810a53fa>] warn_slowpath_null+0x1a/0x20
[ 176.266564] [<ffffffff810ad9ea>] local_bh_enable_ip+0x7a/0xa0
[ 176.266564] [<ffffffff819308c9>] _raw_spin_unlock_bh+0x19/0x20
[ 176.266564] [<ffffffff8123dbda>] proc_free_inum+0x3a/0x50
[ 176.266564] [<ffffffff8111d0dc>] free_pid_ns+0x1c/0x80
[ 176.266564] [<ffffffff8111d195>] put_pid_ns+0x35/0x50
[ 176.266564] [<ffffffff810c608a>] put_pid+0x4a/0x60
[ 176.266564] [<ffffffff8146b177>] tty_ioctl+0x717/0xc10
[ 176.266564] [<ffffffff810aa4d5>] ? wait_consider_task+0x855/0xb90
[ 176.266564] [<ffffffff81086bf9>] ? default_spin_lock_flags+0x9/0x10
[ 176.266564] [<ffffffff810cab0a>] ? remove_wait_queue+0x5a/0x70
[ 176.266564] [<ffffffff811e37e8>] do_vfs_ioctl+0x98/0x550
[ 176.266564] [<ffffffff810b8a0f>] ? recalc_sigpending+0x1f/0x60
[ 176.266564] [<ffffffff810b9127>] ? __set_task_blocked+0x37/0x80
[ 176.266564] [<ffffffff810ab95b>] ? sys_wait4+0xab/0xf0
[ 176.266564] [<ffffffff811e3d31>] sys_ioctl+0x91/0xb0
[ 176.266564] [<ffffffff810a95f0>] ? task_stopped_code+0x50/0x50
[ 176.266564] [<ffffffff81939199>] system_call_fastpath+0x16/0x1b
[ 176.266564] ---[ end trace 387af88219ad6143 ]---
It turns out that spin_unlock_bh(proc_inum_lock) is not safe when
put_pid is called with another spinlock held and irqs disabled.
For now take the easy path and use spin_lock_irqsave(proc_inum_lock)
in proc_free_inum and spin_loc_irq in proc_alloc_inum(proc_inum_lock).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Oleg pointed out that in a pid namespace the sequence.
- pid 1 becomes a zombie
- setns(thepidns), fork,...
- reaping pid 1.
- The injected processes exiting.
Can lead to processes attempting access their child reaper and
instead following a stale pointer.
That waitpid for init can return before all of the processes in
the pid namespace have exited is also unfortunate.
Avoid these problems by disabling the allocation of new pids in a pid
namespace when init dies, instead of when the last process in a pid
namespace is reaped.
Pointed-out-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
The sequence:
unshare(CLONE_NEWPID)
clone(CLONE_THREAD|CLONE_SIGHAND|CLONE_VM)
Creates a new process in the new pid namespace without setting
pid_ns->child_reaper. After forking this results in a NULL
pointer dereference.
Avoid this and other nonsense scenarios that can show up after
creating a new pid namespace with unshare by adding a new
check in copy_prodcess.
Pointed-out-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Sedat reported the following commit caused a regression:
commit 9650388b5c56578fdccc79c57a8c82fb92b8e7f1
Author: Eric Dumazet <edumazet@google.com>
Date: Fri Dec 21 07:32:10 2012 +0000
ipv4: arp: fix a lockdep splat in arp_solicit
This is due to the 6th parameter of arp_send() needs to be NULL
for the broadcast case, the above commit changed it to an all-zero
array by mistake.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull i2c __dev* attribute removal from Wolfram Sang:
"The squashed patches from Bill to get rid of the __dev* annotations in
the i2c subsystem. I couldn't include it in my previous pull request
due to some dependency with the mfd subsystem. I had this patch in
linux-next for two days before rc1 and nothing popped up."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux:
i2c: remove __dev* attributes from subsystem
|
|
Teach pgdat_balanced() about order-0 allocations so that we can simplify
code in a few places in vmstat.c.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
controls API failures"
Commit f0ed2ce840b3 ("[media] uvcvideo: Set error_idx properly for
extended controls API failures") causes user space to behave incorrectly
on one of my test machines (there is no sound under KDE 4.9.4 using
pulseaudio and there is a knotify4 process occupying one of the CPU
cores 100% of the time). Reverting that commit entirely fixes the
problem for me.
However, commit f0ed2ce840b3 appears to do more than it follows from its
changelog, because the changelog only says about the changes related to
ctrls->error_idx, while the commit additionally changes error codes
returned by various functions in uvc_ctrl.c and uvc_v4l2.c. It turns
out that the changes of the returned error codes confuse the user spce,
so it is sufficient to revert the part of commit f0ed2ce840b3 not
mentioned in its changelog to fix the problem.
[ 'ENOENT' is not a valid error return from an ioctl to begin with, and
I don't understand how anybody ever even thought it would be. - Linus ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 68136b10 ("ARM: sunxi: Change device tree naming scheme for
sunxi") changed the naming scheme and the compatible strings used in the
device trees related to the sunXi platform, but forgot to change the
compatible string in the DT machine definition.
This prevents the kernel from booting on these boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
