| Age | Commit message (Collapse) | Author |
|---|
|
Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Permanent MAC is wrongly supplied in create iface command. Call the
command with no MAC address and then MAC address should be later queried
and applied.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
instead of raw assignment to current->state
Signed-off-by: Hong Zhiguo <honkiko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the bnx2x's ethtool interface to enable
control in the eee feature, as well as report statistic information
about it.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds energy efficient energy support (802.3az) to bnx2x
boards with 84833 phys (and sufficiently new BC and external FW).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the kernel's ethtool interface by adding support
for 2 new EEE commands - get_eee and set_eee.
Thanks goes to Giuseppe Cavallaro for his original patch adding this support.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__alloc_skb() now extends tailroom to allow the use of padding added
by the heap allocator.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case
of inband vlan. Because of incorrect protcol type driver
was setting incorrect opcode. This resulted in adapter calculating
checksum incorrectly.
o Updated driver version to 5.0.29
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add debug messages for FW CDRP command failure.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We added another error condition here, but if we were to hit it then
we need to unregister_netdev() before doing the free_netdev().
Otherwise we would hit the BUG_ON() in free_netdev():
BUG_ON(dev->reg_state != NETREG_UNREGISTERED);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for an external 26 MHz crystal source.
[Changed wl->ref_clock to priv->ref_clock -- Luca.]
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.
[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]
[Make the pre_pkt_send operation optional -- Luca]
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).
[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
Signed-off-by: Orit Brayer <orit@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
PG2 requires 4 new parameters that to be passed to the PHY.
Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.
[Make sure PG1 still gets the original struct - Arik]
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
PG2 has a unique chip id. It supports similar HW quirks.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
was hardcoded 252, now uses the parameters struct size.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
|
|
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The mask option allows you put all address belonging that mask into
the same recent slot. This can be useful in case that recent is used
to detect attacks from the same network segment.
Tested for backward compatibility.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
because reply packets need to go to the same nfqueue, src/dst ip
address were xor'd prior to jhash().
However, this causes bad distribution for some workloads, e.g.
flows a.b.1.{1,n} -> a.b.2.{1,n} all share the same hash value.
Avoid this by hashing both. To get same hash for replies,
first argument is the smaller address.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for cttimeout.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since the sysctl data for l[3|4]proto now resides in pernet nf_proto_net.
We can now remove this unused fields from struct nf_contrack_l[3,4]proto.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch modifies the GRE protocol tracker, which partially
supported namespace before this patch, to use the new namespace
infrastructure for nf_conntrack.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch modifies the DCCP protocol tracker to use the new
namespace infrastructure for nf_conntrack.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for UDPlite protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for SCTP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for IPv6 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for IPv4 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for ICMPv6 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for ICMP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for UDP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for TCP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds namespace support for the generic layer 4 protocol
tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch prepares the namespace support for layer 3 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_l3proto_[un]register_sysctl.
* nf_conntrack_l3proto_[un]register.
We add a new nf_ct_l3proto_net is used to get the pernet data of l3proto.
This adds rhe new struct nf_ip_net that is used to store the sysctl header
and l3proto_ipv4,l4proto_tcp(6),l4proto_udp(6),l4proto_icmp(v6) because the
protos such tcp and tcp6 use the same data,so making nf_ip_net as a field
of netns_ct is the easiest way to manager it.
This patch also adds init_net to struct nf_conntrack_l3proto to initial
the layer 3 protocol pernet data.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch prepares the namespace support for layer 4 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_[un]register_sysctl
* nf_conntrack_l4proto_[un]register
to include the namespace parameter. We still use init_net in this patch
to prepare the ground for follow-up patches for each layer 4 protocol
tracker.
We add a new net_id field to struct nf_conntrack_l4proto that is used
to store the pernet_operations id for each layer 4 protocol tracker.
Note that AF_INET6's protocols do not need to do sysctl compat. Thus,
we only register compat sysctl when l4proto.l3proto != AF_INET6.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Implement a new "fail-open" mode where packets are not dropped
upon queue-full condition. This mode can be enabled/disabled per
queue using netlink NFQA_CFG_FLAGS & NFQA_CFG_MASK attributes.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Vivek Kashyap <vivk@us.ibm.com>
Signed-off-by: Sridhar Samudrala <samudrala@us.ibm.com>
|
|
It was scheduled to be removed.
Cc: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It was scheduled to be removed.
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds the support for D_CAN controller driver to the existing
C_CAN driver.
Bosch D_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be
obtained from: http://www.semiconductors.bosch.de/media/en/pdf/
ipmodules_1/can/d_can_users_manual_111.pdf
A new array is added for accessing the d_can registers, according to d_can
controller register space.
Current D_CAN implementation has following limitations, this is done
to avoid large changes to the C_CAN driver.
1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP
supports upto 32 message objects but in case of D_CAN we can configure
upto 128 message objects.
2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers.
3. These patches have been tested on little endian machine, there might
be some hidden endian-related issues due to the nature of the accesses
(32-bit registers accessed as 2 16-bit registers). However, I do not
have a big-endian D_CAN implementation to confirm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
c_can uses overlay structure for accessing c_can module registers.
With this kind of implementation it is difficult to add one more ip
which is similar to c_can in functionality but different register
offsets.
This patch changes the overlay structure implementation to an array
with register offset as index. This way we can overcome the above
limitation.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John Linville says:
====================
Amitkumar Karwar gives us a cfg80211 fix that changes some state
tracking in order to avoid a WARNING.
Arik Nemtsov provide a mac80211 fix for an RCU-related race.
Avinash Patil shares a pair of mwifiex fixes, one which invalidates
some stale configuration data before a channel change and another to
restrict hidden SSID support to zero-length SSIDs only.
Chun-Yeow Yeoh brings a mac80211 fix for a mesh problem triggered
when combining multiple mesh networks into one.
Felix Fietkau provides a mac80211 lockdep fix.
Joe Perches fixes a couple of thinkos related to bitwise operations.
Johannes Berg comes through with a flurry of fixes. The iwlwifi ones
address a problem Linus recently reported, and some of the fallout
discovered while fixing it. The mac80211 fix properly cleans-up
remain-on-channel work on an interface that is stopped. The others
are clean-ups for regressions caused by stricter checking of possible
virtual interfaces supported by wireless drivers.
Meenakshi Venkataraman provides a mac80211 fix for an off-by-one error.
Seth Forshee provides a fix to make the wireless adapters used in
some Mac boxes work after being in S3 power saving state.
Stanislaw Gruszka offers a copule of fixes, a fix for a mac80211
scanning regression and an rt2x00 fix to avoid some lockdep spew.
Last but not least, Vinicius Costa Gomes provides a bluetooth fix
for a typo that "was preventing important features of Bluetooth
from working".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The preferred URL is http://wireless.kernel.org/
rather than http://linuxwireless.org/, update all
URLs to point there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
