summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-08-05ath9k: Fix antenna control init for AR9485Sujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Remove ath_ant_comb_update()Sujith Manoharan
During a HW reset, the diversity config is programmed in the set_board_values() eeprom callback, there is no need to do it again by calling ath_ant_comb_update(). Fixed antenna support is not fully handled for 1-stream cards, it can be done later. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05hostap: do not return positive number on failure path in prism2_open()Alexey Khoroshilov
prism2_open() as an .ndo_open handler should not return positive numbers in case of failure, but it does return 1 in a couple of places. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Support ANT diversity for WB225Sujith Manoharan
WB225 based cards like CUS198 and CUS230 support both fast antenna diversity and LNA combining. Add support for this and also program the SWCOM register with the correct "ant_ctrl_comm2g_switch_enable" value. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Set SWCOM value for CUS198Sujith Manoharan
CUS198/CUS230 cards require a custom value to be programmed into the SWCOM register. Assign this during init time. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Remove "shared_chain_lnadiv"Sujith Manoharan
This variable is redundant since we can use common->bt_ant_diversity to determine if diversity has to be enabled/disabled. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Program HW for WB195 diversitySujith Manoharan
The MC_GAIN_CTL/CCK_DETECT registers have to be programmed with the correct configuration values if WLAN/BT RX diversity is enabled. Add this and also take care of the BTCOEX mode when fast diversity is enabled/disabled. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Enable WLAN/BT Ant Diversity for WB225/WB195Sujith Manoharan
A custom solution for Asus is WB195 based and supports WLAN/BT Rx diversity. Identify this card and set the capability. CUS198/CUS230, which are based on WB225 also support WLAN/BT Rx diversity. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Rename ath9k_hw_antctrl_shared_chain_lnadivSujith Manoharan
Use "ath9k_hw_set_bt_ant_diversity" instead. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Add a HW capability for WLAN/BT RX diversitySujith Manoharan
Make use of this capability to restrict the usage of the debugfs file and modparam using which this feature can be enabled. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Cleanup WLAN/BT RX diversitySujith Manoharan
For single-chain WLAN+BT cards, the BT antenna can be used for WLAN RX when the BT interface is disabled. Rename the modparam "antenna_diversity" to "bt_ant_diversity" to clarify this. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Fix antenna diversity for CUS198Sujith Manoharan
CUS198/CUS230 need a few tweaks in the antenna diversity algorithm to accomodate RSSI variation. Add a couple of knobs to control low RSSI threshold and fast antenna diversity bias values. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Print LNA combining mode during initSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Add information about antenna diversitySujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-02Merge tag 'for-linville-20130730' of git://github.com/kvalo/ath6klJohn W. Linville
2013-08-02Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
2013-08-01ath9k: Add statistics for antenna diversitySujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Use a subroutine to calculate ALT ratioSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Simplify checks in quick_scanSujith Manoharan
There is a function to do a ratio comparison for ALT, so make use of it. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Use a helper function for checking LNA optionsSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Use a subroutine to try LNA switchSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Add ALT check for cards with GROUP-3 configSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Use a subroutine to check for short scanSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Do a quick scan only when scan_not_start is trueSujith Manoharan
Right now, it is being done for all cases. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ath9k: Add a debugfs file for antenna diversitySujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01iwl4965: better skb management in rx pathStanislaw Gruszka
4965 version of Eric patch "iwl3945: better skb management in rx path". It fixes several problems : 1) skb->truesize is underestimated. We really consume PAGE_SIZE bytes for a fragment, not the frame length. 2) 128 bytes of initial headroom is a bit low and forces reallocations. 3) We can avoid consuming a full page for small enough frames. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01ssb: drop BROKEN from SSB_SFLASHRafał Miłecki
With recent patches ssb can fetch info about serial flash and register it as a platform device. No more reasons to mark it BROKEN. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01rtlwifi: rtl8192cu: fix function declaration headerMark Schulte
Move rtl92cu_update_hal_rate_tbl declaration to hw.h to correspond with function definition in hw.c. Fixes sparse warning in hw.c warning: symbol 'rtl92cu_update_hal_rate_tbl' was not declared. Signed-off-by: Mark Schulte <schultetwin@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01mwifiex: populate rates in probe request using cfg80211_scan_requestAvinash Patil
Whenever available, use cfg80211_scan_request to populates rates in outgoing probe request. This will help to advertise band specific rates and fix an issue where 11b rates were advertised in probe request going out on 11a band. This will also ensure that we do not advertise 11b rates while P2P scan is going on. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01mwifiex: fix adapter pointer dereference issueAmitkumar Karwar
It has introduced by recent commit 6b41f941d7cd: "mwifiex: handle driver initialization error paths" which adds error path handling for mwifiex_fw_dpc(). release_firmware(adapter->*) is called for success as well as failure paths. In failure paths, adapter is already freed at this point. The issue is fixed by moving mwifiex_free_adapter() call. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-01Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-07-31iwlwifi: mvm: advertise support for DYNAMIC / STATIC SMPSEmmanuel Grumbach
This feature is fully supported by iwlwmvm, so advertise it. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: add high temperature SKU thermal throttling parametersEytan Lifshitz
When the NIC is expected to operate in high temperature, it is advisable to put more aggresive thermal throttling parameters, in order to prevent CT-kill. Signed-off-by: eytan lifshitz <eytan.lifshitz@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: list Emmanuel in maintainers fileJohannes Berg
Wey-Yi has moved on a while ago, but we forgot to update the maintainers file. Since Emmanuel is de facto maintaining the driver along with myself now, list him instead. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Change beacon abort escape time valueAlexander Bondar
Set beacon abort escape timer values - 6 beacons in D0 state, 9 beacons in D3 and D0i3. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: remove duplicate rate scale init codeEyal Shapira
The rate scale windows are cleared twice as part of the init. Cleanup this duplication in both mvm and dvm. Signed-off-by: Eyal Shapira <eyal@wizery.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: remove obsolete flag in TX command APIEmmanuel Grumbach
This API isn't valid any more. It wasn't used anyway. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: report per-chain signal to mac80211Johannes Berg
Instead of reporting the maximum signal strength and the antenna bitmap in the antenna field (which is really just for radiotap and defined differently), report the signal strength values per chain and set the chain bitmap. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: fix debugfs restart if fw_restart is disabledEran Harary
If fw_restart is disabled, using the fw_restart debugfs file will enable fw_restart and then send the failing command, but this still frequently fails restart because it resets fw_restart afterwards and is thus racy. Fix this by tracking fw_restart separately and allowing "always restart", "never restart" and "restart N times". Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Change beacon filtering commandHila Gonen
Change beacon filtering command due to a change in the API. In case the FW supports the old API, we do not send the BF HCMD and assume that since the corresponding struct in the FW is zeroed by default then we don't need to disable it in the FW actively. Signed-off-by: Hila Gonen <hila.gonen@intel.com> Signed-off-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: register vif debugfs for AP mode tooEmmanuel Grumbach
The current registered the per-vif debugfs handler for STA mode only. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2013-07-31iwlwifi: mvm: split constants into separate fileJohannes Berg
To make maintaining some constant default values in the driver easier, declare them in a separate file. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: assign quota per virtual interfaceJohannes Berg
Instead of assigning quota per used binding (channel) assign the same amount of quota for each virtual interface so that when there are more than two interfaces using more than one channel, we'll stay on the channels proportionally to the number of virtual interfaces using the channels. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Return on inconsistency in add interfaceIlan Peer
Return in case that HW restart is in progress but the added interface is not found during the iteration over all the interfaces. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Change AM->PSM timeout for EAPOL framesAlexander Bondar
Currently after sending EAPOL frame FW transition to power saving mode within 10 or 100 msec (as specified by power table command). According to new requirement this timeout for a specific EAPOL frame must be controlled by the driver by setting tx_pm_timeout field of TX_CMD to 2 (PM_FRAME_ENUM_MGMT). This value corresponds to 32 msec timeout. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: support six IPv6 addresses in D3Johannes Berg
Newer firmware supports offloading more IPv6 addresses for NDP, adjust the code to send the correct command depending on the firmware capability. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Enable user set TX powerMatti Gottlieb
Support Tx power limitations. These limitations can come from mac80211 for various reasons. Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: reprobe device on firmware error during restartJohannes Berg
If we get a firmware error during restart, we currently abandon any hope and simply fail, getting stuck until the driver is reloaded. Unfortunately, there isn't really much else we can do since restart will likely continue to fail, and asking mac80211 for disconnection just causes more error. To allow the user to at least set up the device again completely from scratch, reprobe the device and in doing so completely destroy any mac80211/driver state. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: remove the default calibration values for 7000Emmanuel Grumbach
The fw is now able to run TX_IQ_SKEW and RX_IQ_SKEW by itself. No need for default values any more. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Dor Shaish <dor.shaish@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: new api to get signal strengthAvri Altman
A new API that replaces the rx signal strength calculation via agc & rssi. The energy is now calculated outside the driver and transferred by the fw. Signed-off-by: Avri Altman <avri.altman@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v0.10.2 at 2024-08-22 05:30:38 (GMT)