| Age | Commit message (Collapse) | Author |
|---|
|
The recently introduced pci_prepare_to_sleep() needs the following fix,
because there are systems which are not power manageable by ACPI (ie.
ACPI doesn't provide methods to put the device into low power states and
back), but require ACPI hooks to be executed for wake-up to work.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
John Keller reports that PCI config space access is broken on machines
with more than one domain. conf1 accesses only work for domain 0, so make sure
we check the domain number in the raw routines before trying conf1.
Reported-by: John Keller <jpk@sgi.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
So that one of the several config option permutations will build again.
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
If the offset of PCI device's PM capability in its configuration space,
the mask of states that the device supports PME# from and the D1 and D2
support bits are cached in the corresponding struct pci_dev, the PCI
device PM code can be simplified quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Introduce functions pci_prepare_to_sleep() and pci_back_from_sleep(),
to be used by the PCI drivers that want to place their devices into
the lowest power state appropiate for them (PCI_D3hot, if the device
is not supposed to wake up the system, or the deepest state from
which the wake-up is possible, otherwise) while the system is being
prepared to go into a sleeping state and to put them back into D0
during the subsequent transition to the working state.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Introduce additional flag 'prepared' in struct acpi_device_wakeup_flags
and use it to prevent devices from being enable/disabled do wake up the
system multiple times in a row (this does not happen currently, but will
be possible after some of the following patches).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The currect ACPI code attempts to execute _PSW at three different
places and in one of them only it tries to execute _DSW before _PSW,
which is inconsistent with the other two cases.
Move the execution of _DSW and _PSW into a separate function called
acpi_device_sleep_wake() and call it wherever appropriate instead of
executing _DSW and/or _PSW directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Rework pci_set_power_state() so that the platform callback is
invoked before the native mechanism, if necessary. Also, make
the function check if the device is power manageable by the
platform before invoking the platform callback.
This may matter if the device dependent on additional power
resources controlled by the platform is being put into D0, in which
case those power resources must be turned on before we attempt to
handle the device itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Introduce function pointer platform_pci_power_manageable to be used
by the platform-related code to point to a function allowing us to
check if given device is power manageable by the platform.
Introduce acpi_pci_power_manageable() playing that role for ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Introduce function acpi_bus_power_manageable() allowing other
(dependent) subsystems to check if ACPI is able to power manage given
device. This may be useful, for example, for PCI device power
management.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Also fixes up the sparc code that was assuming this is not a constant.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This changes pci_setup_device to handle pci_name() now returning a
constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
When CONFIG_PCI=n, there is no stub for pci_set_consistent_dma_mask(),
so add one like other similar stubs. Otherwise there can be build errors,
as here:
linux-next-20080630/drivers/ssb/main.c:1175: error: implicit declaration of
function 'pci_set_consistent_dma_mask'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Russell King did the following back in 2003:
<-- snip -->
[PCI] pci-9: Kill per-architecture pcibios_update_resource()
Kill pcibios_update_resource(), replacing it with pci_update_resource().
pci_update_resource() uses pcibios_resource_to_bus() to convert a
resource to a device BAR - the transformation should be exactly the
same as the transformation used for the PCI bridges.
pci_update_resource "knows" about 64-bit BARs, but doesn't attempt to
set the high 32-bits to anything non-zero - currently no architecture
attempts to do something different. If anyone cares, please fix; I'm
going to reflect current behaviour for the time being.
Ivan pointed out the following architectures need to examine their
pcibios_update_resource() implementation - they should make sure that
this new implementation does the right thing. #warning's have been
added where appropriate.
ia64
mips
mips64
This cset also includes a fix for the problem reported by AKPM where
64-bit arch compilers complain about the resource mask being placed
in a u32.
<-- snip -->
This patch removes the unused pcibios_update_resource() functions the
kernel gained since, from FRV, m68k, mips & sh architectures.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Make pci_setup_device() write the bus ID directly into the allotted storage,
rather than using pci_name() as the address as that now returns a const
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
struct pci_driver has no field of driver_data.
It's in pci_device_id.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp driver saves its private data pointer into pci_dev
structure using pci_set_drvdata()/pci_get_drvdata(). But because
pciehp is not a pci device driver but a PCI Express service driver, it
should save its private data pointer into pcie_device structure using
set_service_data()/get_service_data().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Currently, pciehp driver enables command completed interrupt as follows.
(1) Don't enable at initialization.
(2) Enable command completed interrupt whenever pciehp issues a
command, if the command doesn't attempt to disable the interrupt.
(3) Disable command completed interrupt at driver unloading.
Once we enable command completed interrupt, we don't need to re-enable
it for every command. So we can simplify above steps as follows:
(1) Enable command completed interrupt at initialization.
(2) No special sequence for command completed interrupt.
(3) Disable command completed interrupt at driver unloading.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp driver's intialization sequence is as follows:
(1) initialize controller data structure
(2) install interrupt handler
(3) enable software notification
(4) initialize controller specific slot data structure
(5) initialize generic slot data structure and register it to pci hotplug core
The interrupt handler of pciehp assumes that controller specific slot
data structure is already initialized. However, it is installed at (2)
before initializing controller specific slot data structure at
(4). Because of this, pciehp driver cannot handle the following cases
properly.
- If devices that shares IRQ with pciehp raise interrupts between (2) and (4).
- If hotplug events (e.g. MRL open) happen between (3) and (4).
We already have a workaround for this problem ("pciehp: fix NULL
dereference in interrupt handler: dbd79aed1aea2bece0bf43cc2ff3b2f9baf48a08).
But we still need fundamental fix.
This patch fix the problem by changing the initilization sequence as follows:
(1) initialize controller data structure
(2) initialize controller specific slot data structure
(3) install interrupt handler
(4) enable software notification
(5) initialize generic slot data structure and register it to pci hotplug core
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
If pci_request_region fails, make the warning include the resource number,
not the resource number + 1.
|
|
Convert printks to use dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Convert printks to use dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Convert printks to use dev_printk().
I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled
only when DEBUG is defined.
I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.
I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.
I tried to make the resource assignment formats more consistent, e.g.,
"BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The pcie_poll_cmd() and pcie_wait_cmd() are too large to be
inlined.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change command polling frequency to 100Hz from 10Hz in order to reduce
the delay in the common case of a command completing quickly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup pcie_poll_cmd(): check the slot status once before entering our
completion test loop and convert the loop to a simpler while() block.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the typo in hpc_release_ctlr().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
A few warnings snuck in as parameters were added or renamed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
On x86, we do early PCI probing to apply some quirks for chipset bugs.
However, in a recent cleanup (7bcbc78dea92fdf0947fa48e248da3c993a5690f) a
thinko was introduced that causes us to probe all subfunctions of even single
function devices (a function was factored out of an inner loop and a "break"
became a "return"). Fix that up by making check_dev_quirk() return a value so
we can keep the factored code intact.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
ACPI PM: Add possibility to change suspend sequence
There are some systems out there that don't work correctly with
our current suspend/hibernation code ordering. Provide a workaround
for these systems allowing them to pass 'acpi_sleep=old_ordering' in
the kernel command line so that it will use the pre-ACPI 2.0 ("old")
suspend code ordering.
Unfortunately, this requires us to add a platform hook to the
resuming of devices for recovering the platform in case one of the
device drivers' .suspend() routines returns error code. Namely,
ACPI 1.0 specifies that _PTS should be called before suspending
devices, but _WAK still should be called before resuming them in
order to undo the changes made by _PTS. However, if there is an
error during suspending devices, they are automatically resumed
without returning control to the PM core, so the _WAK has to be
called from within device_resume() in that cases.
The patch also reorders and refactors the ACPI suspend/hibernation
code to avoid duplication as far as reasonably possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 into linux-next
|
|
Remove the obsolete workaround for a Toshiba Satellite 4030cdt
S1 problem from drivers/acpi/sleep/main.c .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Detect all physical PCI slots as described by ACPI, and create entries in
/sys/bus/pci/slots/.
Not all physical slots are hotpluggable, and the acpiphp module does not
detect them. Now we know the physical PCI geography of our system, without
caring about hotplug.
[kaneshige.kenji@jp.fujitsu.com: export-kobject_rename-for-pci_hotplug_core]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Greg KH <greg@kroah.com>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix build with CONFIG_DMI=n]
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Currently, /sys/bus/pci/slots/ only exposes hotplug attributes when a
hotplug driver is loaded, but PCI slots have attributes such as address,
speed, width, etc. that are not related to hotplug at all.
Introduce pci_slot as the primary data structure and kobject model.
Hotplug attributes described in hotplug_slot become a secondary
structure associated with the pci_slot.
This patch only creates the infrastructure that allows the separation of
PCI slot attributes and hotplug attributes. In this patch, the PCI
hotplug core remains the only user of this infrastructure, and thus,
/sys/bus/pci/slots/ will still only become populated when a hotplug
driver is loaded.
A later patch in this series will add a second user of this new
infrastructure and demonstrate splitting the task of exposing pci_slot
attributes from hotplug_slot attributes.
- Make pci_slot the primary sysfs entity. hotplug_slot becomes a
subsidiary structure.
o pci_create_slot() creates and registers a slot with the PCI core
o pci_slot_add_hotplug() gives it hotplug capability
- Change the prototype of pci_hp_register() to take the bus and
slot number (on parent bus) as parameters.
- Remove all the ->get_address methods since this functionality is
now handled by pci_slot directly.
[achiang@hp.com: rpaphp-correctly-pci_hp_register-for-empty-pci-slots]
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: make headers_check happy]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: fix typo in #include]
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Register one slot per slot, rather than one slot per function. Change the
name of the slot to fake%d instead of the pci address.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Just concentrate PCI traffic at linux-pci@vger rather than splitting it between
vger and a sf.net moderated (!) mailing list.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Scott Murray <scottm@somanetworks.com>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
fix BLK_DEV_HD_ONLY on ARM dependencies
ide: export ide_doubler
palm_bk3710: add warm-plug support
delkin_cb: add missing __init/__exit tags
delkin_cb: add warm-plug support
delkin_cb: use struct ide_port_info
delkin_cb: set proper hwif->gendev.parent value
ide: fix host drivers missing hwif->chipset initialization
ide-generic: add missing hwif->chipset setup
sis5513: add missing pci_enable_device() call
MAINTAINERS: remove SIS 5513 IDE entry
ide: remove the ide_etrax100 chipset type
|
|
This patch unhides the SMBus on Compaq Deskpro EN
SFF P667 with the Intel 815E chipset. Unhiding it reveals
a THMC51 hardware monitoring chip.
Jean Delvare has checked that this machine has no ACPI
magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
The patch was tested on Fedora Core 9 with 2.6.25.4 kernel.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rafał Haładuda <rh1985@wp.pl>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch limits BLK_DEV_HD_ONLY to the ARM platforms offering
IRQ_HARDDISK, fixing the following compile error on others:
<-- snip -->
...
CC drivers/ide/legacy/hd.o
...
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'hd_times_out':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: 'IRQ_HARDDISK' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'do_hd_request':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:661: error: 'IRQ_HARDDISK' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'hd_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:765: error: 'IRQ_HARDDISK' undeclared (first use in this function)
make[3]: *** [drivers/ide/legacy/hd.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This patch fixes the following build error:
<-- snip -->
...
Building modules, stage 2.
MODPOST 1204 modules
ERROR: "ide_doubler" [drivers/ide/ide-core.ko] undefined!
...
make[2]: *** [__modpost] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Don't fail the probe if there are no devices attached to the controller.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Don't fail the probe if there are no devices attached to the controller.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Convert the driver to use struct ide_port_info - as a nice side-effect
this fixes racy setup of ->io_32bit/unmask settings (after ide_device_add()
call device can be already in use).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
hwif->dev was set too late (after ide_device_add() call)
so hwif->gendev.parent was not initialized properly.
Fix it by setting hw.dev and letting ide_init_port_hw()
do the rest.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
ide_find_port() now depends on ->chipset being set for occupied ide_hwifs[]
slots so all host drivers have to initialize hwif->chipset properly.
This patch fixes a regression on hosts with > 1 port or with a single port
but no devices attached to it for an affected host drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
